JSA Gathering Tent
BASIC JOB STEP POTENTIAL CONTROLS Ac
HAZARDS Part
1.0 Transportation of 1.1 Narrow road/ Ensure valid vehicle driving license Superv
material to site collision or topple Observe proper traffic control and speed limit
Equipment or material should be properly
secure
Warning signs shall be erected as means of
warning where applicable. Superv
1.2 Insecure
Properly secure the equipment and material
instrument on
vehicle Ensure right position of the equipment and
material is properly set on the vehicle
No person allowed to sit/present on the back of
truck lorry.
2.0 Loading and unloading 2.1 Improper manual Toolbox briefing Superv
of handling method Proper manual handling method.
Permit Re
Close supervision by Work Supervisor.
material
Maintain good housekeeping
Work related PPE to be worn.
Toolbox briefing – drop object and lifting
use tagline during lifting
2.2 Falling load
provide signalman Superv
Provide signages Permit Re
Only competent operator is allowed to
operate
the crane
Superv
Crane functional test to be done before
commencing the work
2.3 Pinch Point / Will isolate the working area to ensure public
sharp edges safety
Using Proper PPE
(hand glove/ long sleeve jacket) Proper
handling method
3.1 Pinch Point / Toolbox briefing – Pinch point.
3.0 Preparing the foundation sharp edges Superv
Using Proper PPE (hand glove/ long sleeve
and material at respective jacket)
installation point
Ensure proper handling on tools before Superv
3.2 Manual performing the job
Handling.
Trained the workers correct way to lift material
Ensure all workers follow the correct procedure
Clearance of loose material
Post Signages as a way to increase awareness
4.1 Pinch Point / Toolbox briefing – Pinch point.
sharp edges Using Proper PPE (hand glove/ long sleeve Superv
jacket)
Will install edge protector
JSA Gathering Tent
4.2 Sharp object Proper PPE to be
worn
Supervisor
Put warning signages
Barricade all protrusion hazard
4.0 Assembly of material
5.0 Installation of gathering Toolbox briefing – drop object and lifting
Tent 5.1 Falling load use tagline during lifting
Superv
provide signalman
Provide signages
Only competent operator is allowed to operate
the crane Crane functional test to be done before
commencing the work
all lifting gear will be inspected before use
5.2 Pinch Point / Will isolate the working area to ensure public
sharp edges safety
Work related PPE to be worn.
Posting Warning Signage
Toolbox briefing – Pinch point.
Using Proper PPE (hand glove/ long sleeve Superv
jacket)
5.3 Manual
Handling.
Toolbox briefing
Proper manual handling method.
Close supervision by Work Supervisor.
Maintain good housekeeping
Work related PPE to be worn. Superv
5.4 Working at
height wear full body harness
Close supervision by supervisor
Provide suitable working platform
6.0 Bolt tightening and 6.1 Working at Toolbox briefing – Working at height
height (Bad weather) Inspect safety harness before use
alignment work Superv
Ensure workers are using correct tools
Tight supervision from supervisor
Use skylift to tighten the bolt
Provide safe working platform
Stop the work
6.2 Pinch Point / Outrigger fully extends Superv
sharp edges Training of personnel
Posting Warning Signage
Toolbox briefing – Pinch point.
Using Proper PPE (hand glove/ long sleeve
JSA Gathering Tent
jacket)
Toolbox briefing
6.3 Manual
Handling. Proper manual handling method.
Close supervision by Work Supervisor. Superv
Maintain good housekeeping
Work related PPE to be worn.
7.1 Manual handling Toolbox briefing
7.0 Housekeeping Superv
Proper manual handling method.
Close supervision by Work Supervisor.
Maintain good housekeeping
Work related PPE to be worn.
Posting Warning Signage Superv
7.2 Pinch Point /
sharp edges Toolbox briefing – Pinch point.
Using Proper PPE (hand glove/ long sleeve
jacket)
7.3 Slippery Superv
Toolbox briefing
surfaces
Wear appropriate PPE
GENERAL NOTES
Basic PPE (Safety Helmet @ Hard Hat, Safety Shoes, Safety Glass and Long Sleeve Jacket) shall be worn at all the time.
Set up barricades around work area and display warning signs.
All equipment / machinery to be inspected by CTCI before any work commences.
All PTW and supporting permits must be valid before any works begins.
On hearing of emergency siren, stop all works, machinery & source of ignition and walk on foot to the nearest muster p
Vehicle to exit immediately to designated parking area after delivery of material.
JSA Gathering Tent
No eating and resting on site. Use designated eating and resting area.
All pressure gauges used must be calibrated and tagged with valid calibration sticker.
All scaffolding must have a green "safe to use" tag before put into service.
Maintain good housekeeping daily at all the work places.
Tool box talk specific on work instruction and briefing on hazards and control measures to be conducted before start o
