6062 - Multi-purpose Timer

Overview:
Model 6062 programmable timer is suitable for many functions that require a timed operation e.g. Access Control Applications,
Siren/Bell Cut Off Module, Dialer Delay, Guard Tour Supervisory Timer, etc. Some optional functions include: One Shot, Delayed
Release, Delayed Operate, Delayed Pulse and Pulser/Flasher. A new feature has been added which provides a momentary relay acti-
vation at the end of a desired timing cycle. This feature eliminates the need for having to use two (2) timers to achieve this function.

Specifications:
• 12VDC or 24VDC operation is selectable. • One (1) second momentary relay activation at the end of
• Quick and extremely accurate time range adjustment from the timing cycle (eliminates the need to use two (2) timers
1 sec. to 60 min. for this function).
• LED indicates relay is energized. • Built-in reset feature which cancels timing cycle.
• Form “C” relay contacts are 8 amp at 120VAC/28VDC. • Repeat (pulser/flasher) mode.
• Current Draw: Stand-by 3mA, Relay Energized 40mA. • Snap Track compatible (order Altronix model #ST3)
• Triggers via positive DC (+) voltage, dry contact closure, • DIN Rail Mount version available
or removal of contact closure. (order Altronix model #DTMR1).
• Selectable relay activation at the start or end of the Board dimensions: 3”L x 2.5”W x .75”H (approximate)
timing cycle.
Installation Instructions:
1. Mount 6062 in desired location/enclosure.
2. Set proper DC Input Voltage Dip Switch 3: 12VDC ON, 24VDC OFF.
3. Refer to Dip Switch Selection and Jumper Selection Tables for desired functions (e.g.: Timing, Trigger, Pulse)
4. Measure DC input voltage before powering device to ensure proper operation.
5. Refer to Terminal Identification Table and Typical Applications fig. 1 thru fig. 8. for desired wiring connections.
Note: When triggering via a N.O. (normally open), momentary or maintained trigger, connect the dry contact trigger to Pos (+)
and TRG terminals. When triggering via a N.C. (normally closed), momentary or maintained trigger, connect the trigger to Neg. (-)
and TRG terminals and install a resistor [for 12VDC - 2K (2,000 ohm) or for 24VDC - 4.7K (4,700 ohm)]
between the Pos (+) and TRG terminals (Fig. 8).
6. Enable the reset features:
- Cut J3 when power is removed the timer will reset and not re-trigger when power is restored unless a new trigger is applied.
Note: The closed trigger and delayed pulse options will not operate if the reset feature is desired.

Dip Switch Selection Table:

Dip # Off On
1 Relay energizes at the start of timing cycle.* Relay energizes at the end of timing cycle.*
2 1-60 Minutes timing range (trimpot adjustable). 1-60 Seconds timing range (trimpot adjustable).
3 24VDC operating voltage. 12VDC operating voltage.
4 Timing begins immediately upon trigger input. Timing starts after removal of trigger input.
* When relay energizes (LED is on) [N.O. & C] switch from open to close and [N.C. & C] switch from close to open.

Jumper Selection Table:

Number Function/Description
Cutting J1 selects the pulser/flasher mode. Relay will flip ON and OFF
J1
continuously in equally set timed intervals when timer is powered up.
Cutting J2 puts timer in delayed output mode. Relay will pulse for 1 second at
J2
the end of a preset timing cycle. *Dip Switch 1 must be ON for this function.
6062 will go through an initial timing cycle when first powered up unless J3 is cut.
J3
If J3 is cut, timing can only be initiated via TRG terminal.

Terminal Identification:
Terminal
Function/Description
Legend
Applying a positive voltage will activate timing cycle.
TRG
Trigger voltage range: 7-12VDC at 12 volt setting, 15-24VDC at 24 volt setting.
--- , + Connect 12 or 24VDC filtered and regulated voltage. Refer to Dip Switch Selection Table for voltage setting.
N.O., C, N.C. Dry form “C” relay contacts are rated 8 amp at 120VAC/28VDC.
 6062 Typical Applications:
Fig. 1 - Timed Door Annunciator: Fig. 5 - Timed Door Strike:

NC

NC
OFF

OFF
4 3 2 1 4 3 2 1

+ +
CHIME Pos (+) and Neg (--)

C
ON ON
ON

ON
--- terminals constant
4
3
2
1

4
3
2
1
+ --- 12VDC or 24VDC
RELAY CONTROL

RELAY CONTROL
NO

NO
TRIG CONTROL

TRIG CONTROL
---
SEC. / MIN.

SEC. / MIN.
CUT J3 FOR RESET

CUT J3 FOR RESET

12V / 24V

12V / 24V
J2

J2
J3

J3
ON POWER-UP

ON POWER-UP
Door Strike
CUT J2 FOR DELAY PULSE

CUT J2 FOR DELAY PULSE

J1

J1
+
Pos (+) and Neg (--)

+
CUT J1 FOR REPEAT

CUT J1 FOR REPEAT

terminals constant
12VDC or 24VDC
60

60
---
1

1
--

--
TRG

TRG
15

15
45

45
Normally Open Normally Open
Door Contacts Door Contacts

For this application Switch #1 and Switch #4 For this application Switch #1 should be in the OFF
should be in the OFF position. position and Switch #4 should be in the ON position.

Fig. 2 - Guard Tour Supervisory Timer: Fig. 6 - Timed Shunt for a Door: Use to bypass alarm contacts.
NC

NC
OFF

OFF
DIALER OR
4 3 2 1 4 3 2 1

TRANSMITTER
C

C
ON ON
Door Contacts
ON

ON
Protective
4
3
2
1

4
3
2
1
Circuit
RELAY CONTROL

RELAY CONTROL
NO

NO
TRIG CONTROL

TRIG CONTROL
SEC. / MIN.

SEC. / MIN.
CUT J3 FOR RESET

CUT J3 FOR RESET

12V / 24V

12V / 24V
J2

J2
J3

J3
ON POWER-UP

ON POWER-UP
CUT J2 FOR DELAY PULSE

CUT J2 FOR DELAY PULSE

J1

J1
+ +
Pos (+) and Neg (--) Pos (+) and Neg (--)
+

+
CUT J1 FOR REPEAT

CUT J1 FOR REPEAT

terminals constant terminals constant
12VDC or 24VDC 12VDC or 24VDC
60

60
--- ---
1

1
--

--
TRG

TRG
15

15
45

45
Normally Open Normally Open
Switch Contacts Switch Contacts

For this application Switch #1 and Switch #4 For this application Switch #1 should be in the OFF
should be in the OFF position. position and Switch #4 should be in the ON position.

Fig. 3 - Swinger Eliminator: Fig. 7 - Bell Cut Off Timer:

+
NC

NC
Closed Bell
OFF

OFF

4 3 2 1
Circuit
4 3 2 1

or
Siren
Zone on
C

C
ON ON
---
ON

Control Panel
ON
4
3
2
1

4
3
2
1
RELAY CONTROL

RELAY CONTROL
NO

NO
TRIG CONTROL

TRIG CONTROL
SEC. / MIN.

SEC. / MIN.
CUT J3 FOR RESET
12V / 24V

CUT J3 FOR RESET

12V / 24V
J2

J2
J3

J3
ON POWER-UP

ON POWER-UP
CUT J2 FOR DELAY PULSE

CUT J2 FOR DELAY PULSE

J1

J1

+
Pos (+) and Neg (--)
+

+
CUT J1 FOR REPEAT

CUT J1 FOR REPEAT

terminals constant
Bell
12VDC or 24VDC
60

60

--- Output
1

--

--

Protective Control Panel

TRG

TRG

Circuit 12VDC or 24VDC

15

15
45

45

For this application Switch #1 should be in the OFF position For this application Switch #1 should be in the ON position and
and Switch #4 should be in the ON position. Switch #4 is not used in this application.

Fig. 4 - Delay Timer: Use for Door Ajar Alarm, Delayed Fig. 8 - Closed Circuit Trigger Option:
Activation of Digital Dialer, Defrost Cycle Timer, etc...
+ Power
NC
OFF

--- Supply
4 3 2 1
+

Use appropriate contacts

to reporting devices Pull up
C

Resistor
ON
ON

Normally Open
4
3
2
1

Triggering Device
RELAY CONTROL

NO
TRIG CONTROL

SEC. / MIN.

CUT J3 FOR RESET

12V / 24V
J2

J3

--
ON POWER-UP
CUT J2 FOR DELAY PULSE
J1

+
Pos (+) and Neg (--) Closed
+
CUT J1 FOR REPEAT

terminals constant
Circuit
TRG

12VDC or 24VDC
60

---
Contact
1

--
TRG
15
45

For this application Switch #1 should be in the ON position For this application a resistor [for 12VDC - 2K (2,000 ohm)
and Switch #4 is not used in this application. or for 24VDC - 4.7K (4,700 ohm)] must be installed as shown
(resistor not supplied).

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
web site: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A.
II6062 - Rev. 032211 C22K MEMBER