WOT Box Installation Instructions – VW / Audi
Connector Pinout
Pin Color AWG Name Description
1 Yellow 18 RPM Connect to Fuel Injector Drive Signal or Ignition Control Signal (varies by car model)
2 Black 18 Ground Connect to chassis ground
3 Black 16 Power Out Connect to ignition coil power wire going towards the ignition coils.
4 Blue 18 APP Connect to Accelerator Position Sensor or TPS (varies by car model)
5 Green 18 Clutch Connect to Clutch Pedal Position Switch
6 Red 16 Power In Connect to ignition coil power wire going away from the ignition coils.
Installation Instructions
NOTE: If you have a CDI (capacitive discharge ignition system) please contact us at support@n2mb.com for
additional instructions. Damage to your WOT Box can occur if the installation is not completed correctly!
Please visit our website at http://www.n2mb.com to view more pictures of this installation and to get the
latest version of the WOT Box software.
If you need help with the installation, please email support@n2mb.com.
• Disconnect the battery negative terminal.
• Pick out a location to mount the WOT Box. We recommend inside the fuse compartment on the driver's
side of the dash. The WOT Box must be installed inside the passenger compartment since it is not
waterproof. Additionally, you will want to make the WOT Box accessible to the driver, due to the fact that
setting the 2‐step RPM will require holding down the clutch pedal while holding the button on the WOT
Box.
• Locate the rubber grommet on the firewall above the accelerator pedal. Carefully poke a new hole in the
grommet using a sharp object, such as a screwdriver. Be careful not to damage other wires already in the
grommet.
• Bundle the WOT Box 18 AWG YELLOW and 16 AWG RED / BLACK paired wires using electrical tape. Using
a coat hanger or other sharp object, pull the bundle through the grommet in the firewall.
• Route the connector end of the wiring harness to the desired mounting point. Be careful to avoid sharp
metal objects and pinch points. Leave enough of the harness in the passenger compartment to make the
WOT Box easy to get to, but not an excessive amount.
• Locate the ignition coil wiring harness on the driver's side of the cylinder head, near the cam shafts as
shown below. Remove some of the split loom tubing and tape to expose the wires.
• Locate the 4 ignition coil power wires. Refer to the table below to identify the wire colors for your vehicle.
Cut the 4 wires before they join together into two wires and strip both ends of the wires about 5/8".
Car Model / Year Wire Color Pin # at Coil
99–06 Audi TT BLUE / RED
94‐97 Audi B5 A4 BLACK / BLUE
00‐01 Audi B5 A4 RED / GREEN
01‐05 Audi B6 A4 RED / GREEN
Audi C5 A6 (2.7T) RED / GREEN
Audi B5 S4 (2.7T) RED / GREEN
VW Mk4 BLACK / VIOLET
96–99 VW Mk3 2.0L BLACK 3 (smaller gauge black wire)
VW Mk3 VR6 BLACK
98‐05 VW Jetta 1.8T BLACK / VIOLET
98‐05 VW Jetta VR6 BLACK / VIOLET
VW Jetta III VR6 BLACK
96‐00 VW Passat Mk5 BLACK / BLUE
07‐08 SEAT Ibiza 1.8T BLACK/ VIOLET
• Split apart about 6" of the 16 AWG RED / BLACK wire from the WOT Box. Strip the ends of the wires and
slide two pieces of provided heat shrink tubing over the wires. Connect the 16 AWG RED wire from the
WOT Box to the 4 wires previously stripped that are going away from the ignition coils. Connect the 16
AWG BLACK wire to the 4 wires previously stripped that are going towards the ignition coils. Solder the
connection and use the provided heat shrink tubing to cover the connection. Tape up the harness with
electrical tape. Recover the harness with the split loom tubing.
• Locate the negative wire of fuel injector #4, or any other fuel injector that is more convenient. You may tap
into this wire at the fuel injector itself or at the ECU, whichever option is more convenient for you. Refer to
the table below to identify the wire colors for your vehicle. Carefully strip back some of the insulation on
this wire. Be sure to not break the wire. Connect the 18 AWG YELLOW wire from the WOT Box to the
negative wire of fuel injector #4. Solder the connection and cover with electrical tape.
Car Model / Year Recommended Wire Color Pin Number Wire Color Pin
Fuel Injector # @ Fuel Injector @ Fuel @ ECU Number
Injector @ ECU
99–06 Audi TT Injector #4 VIOLET / BLUE 2 VIOLET / BLUE 88
94‐97 Audi B5 A4 Injector #4 BLACK / VIOLET 2 BLACK / VIOLET 65
00‐01 Audi B5 A4 Injector #4 GRAY / VIOLET 2 GRAY / VIOLET 88
01‐05 Audi B6 A4 Injector #4 GRAY / VIOLET 2 GRAY / VIOLET 88
Audi C5 A6 (2.7T) Injector #6 WHITE / YELLOW 2 WHITE / YELLOW 89
Audi B5 S4 (2.7T) Injector #6 WHITE / YELLOW 2 WHITE / YELLOW 89
VW Mk4 1.8T Injector #4 VIOLET / BLUE 2 VIOLET / BLUE 88
96–99 VW Mk3 2.0L Injector #1 BLACK / BLUE 2
VW Mk3 VR6 Injector #6 GRAY / YELLOW 2 GRAY / YELLOW 4
98‐05 VW Jetta 1.8T Injector #4 VIOLET / BLUE 2 VIOLET / BLUE 88
98‐02.5 VW Jetta VR6 Injector #6 GREEN / YELLOW 2 VIOLET / GREEN 89
02.5‐05 VW Jetta VR6 Ignition Coil #1 VIOLET / GREEN 1 VIOLET / GREEN 102
VW Jetta III VR6 Injector #6 GRAY / YELLOW 2 GRAY / YELLOW 2
96‐00 VW Passat Mk5 Injector #4 BLACK / VIOLET 2 BLACK / VIOLET 65
07‐08 SEAT Ibiza 1.8T Injector #4 VIOLET/BLUE 2 VIOLET/BLUE 88
• Secure all of the WOT Box wires using the provided zip ties. Be sure to route the wires away from heat
sources and sharp objects that may damage them. This completes the under‐hood portion of the
installation.
• Back in the passenger compartment, locate the Accelerator Pedal Position Sensor. It is at the gas pedal.
Disconnect the connector.
• Locate the Accelerator Pedal Position Sensor #1 signal wire. Or if your car is not drive by wire, you will tap
into the Throttle Position Sensor. You may tap into this wire at the accelerator pedal or throttle position
sensor itself or at the ECU, whichever option is more convenient for you. Refer to the table below to
identify the wire colors for your vehicle. Carefully strip back some of the insulation on this wire. Be sure to
not break the wire. Connect the 18 AWG BLUE wire from the WOT Box to the Accelerator Pedal Position
(APP) wire. Solder the connection and cover with electrical tape. Reconnect the APP connector.
Car Model / Year Sensor Wire Color Pin Wire Color Pin Number
Type @ Sensor Number @ ECU @ ECU
@ Sensor
99–06 Audi TT Accelerator GRAY / BLUE 4 WHITE / BLUE 35
94‐97 Audi B5 A4 TPS WHITE / YELLOW 5 WHITE / YELLOW 75
00‐01 Audi B5 A4 Accelerator YELLOW / BLUE 4 YELLOW / BLUE 35
01‐05 Audi B6 A4 Accelerator YELLOW / BLUE 4 YELLOW / BLUE 35
Audi C5 A6 (2.7T) Accelerator YELLOW / BLUE 4 YELLOW / BLUE 35
Audi B5 S4 (2.7T) Accelerator YELLOW / BLUE 4 YELLOW / BLUE 35
VW Mk4 Accelerator WHITE / BLUE 4 WHITE / BLUE 35
96–99 VW Mk3 2.0L TPS RED / BLUE 5
VW Mk3 VR6 TPS GREEN / WHITE 5 GREEN / WHITE 40
98‐05 VW Jetta 1.8T Accelerator WHITE / BLUE 4 WHITE / BLUE 35
98‐05 VW Jetta VR6 Accelerator WHITE / BLUE 4 WHITE / BLUE 35
VW Jetta III VR6 TPS GREEN / WHITE 2 GREEN / WHITE 40
96‐00 VW Passat Mk5 TPS WHITE / YELLOW 5 WHITE / YELLOW 75
07‐08 SEAT Ibiza 1.8T Accelerator WHITE/ BLUE 4 WHITE/ BLUE 35
• Locate the Clutch Pedal Position Switch. Disconnect the connector to make the harness easier to access.
• Locate the Clutch Pedal Position Switch signal wire. You may tap into this wire at the Clutch Pedal Position
switch itself or at the ECU, whichever option is more convenient for you. Refer to the table below to
identify the wire colors for your vehicle. Carefully strip back some of the insulation on this wire. Be sure to
not break the wire. Connect the 18 AWG GREEN wire from the WOT Box to the Clutch Pedal Position
Switch (CPP) wire. Solder the connection and cover with electrical tape. Reconnect the CPP connector.
Car Model / Year Wire Color Pin Number Wire Color Pin Number
@ CPP @ CPP @ ECU @ ECU
99–06 Audi TT WHITE / RED 2 WHITE / RED 39
94‐97 Audi B5 A4 RED / GREEN 1 N/A N/A
00‐01 Audi B5 A4 RED / GREEN 1 RED / GREEN 39
01‐05 Audi B6 A4 GREEN / GRAY 2 RED / GREEN 39
Audi C5 A6 (2.7T) RED / GREEN 1 RED / GREEN 39
Audi B5 S4 (2.7T) RED / GREEN 1 RED / GREEN 39
VW Mk4 WHITE / RED 2 WHITE / RED 39
96–99 VW Mk3 2.0L BLACK 2
VW Mk3 VR6 BLACK 2 N/A N/A
98‐05 VW Jetta 1.8T WHITE / RED 2 WHITE / RED 39
98‐05 VW Jetta VR6 WHITE / RED 2 WHITE / RED 39
VW Jetta III VR6 BLACK 2
96‐00 VW Passat Mk5 RED / YELLOW 1 N/A N/A
07‐08 SEAT Ibiza 1.8t BLUE/ORANGE
• Locate a good chassis ground point near where you plan on installing the WOT Box. Try to keep the wire
run as short as possible. It should be under 2’ away, if possible. Next, cut the 18 AWG BLACK wire from the
WOT Box to length. Strip the wire and solidly crimp on the provided ground lug connection. Solder the
ground wire to the ground lug. Connect this ground lug to the chassis. Make sure the metal where you
attach the ground lug is clean, unpainted and free of rust. Use sand paper to prepare the surface, if
needed.
• As an example, we will show it connected at the fuse block. To do this, remove the top attaching screw
from the fuse block. Slide the ground terminal under the fuse block and re‐attach as shown.
• Connect the WOT Box to the harness and tuck the WOT Box into the fuse panel. Re‐install the battery and
all the plastic trim that was removed during the installation. The installation is complete. Proceed to the
testing section below.
•
Troubleshooting ‐ Testing the WOT Box
1. Key on the car but do not start the engine. Press the gas pedal to the floor. You should see the LED on the
WOT Box start to rapidly blink. If it does not, check your APP sensor signal connection (WOT Box BLUE
wire).
2. Next, with the gas pedal still depressed, press the clutch pedal to the floor. You should see the LED on the
WOT Box briefly go out, and then come back on solid for one second and then finally resume blinking
rapidly. If you do not see this, check your Clutch Pedal Position Switch signal connection (WOT Box
GREEN wire).
3. Next, start the engine. Quickly press the gas pedal to the floor and immediately step on the clutch. You
should hear the engine start to rev up, stumble for a short period while the ignition is cut, then return back
on and continue revving. Remove your foot from the gas before you hit the rev limiter. The 2‐step will not
engage if the gas is depressed before the clutch. This is normal. If the engine does not stumble or pause
when the LED turns out, then check the RED/BLACK paired wire. Verify that the RED and BLACK 16 AWG
wires are wired facing the proper way. If they are reversed, the ignition cut will not work.
4. Lastly, test the 2‐Step. Press the clutch pedal down and then quickly press the gas pedal all the way down.
The gas pedal must be floored for the 2‐step to engage. The engine should rev up to the desired RPM and
hold. If it does not, be sure to remove your foot from the gas before you hit the rev limiter. If the 2‐step
does not work, check the Fuel Injector #4 Trigger Signal wire (WOT Box YELLOW wire).
Usage
To use the WOT Shift feature, keep your foot fully on the gas and shift quickly using the clutch. Keep the gas
fully depressed through the shift. The WOT Box will detect the clutch switch signal and briefly cut the ignition
to enable an effortless shift.
To use the 2‐Step feature, fully depress the clutch. Next, fully depress the gas pedal to the floor. The engine
will rev up and hold the RPM that you have set. Quickly release the clutch while leaving the gas fully depressed
to launch the car.
Programming
The WOT Box comes preset for an automatic WOT Shift kill time. This means that the WOT Box will
automatically adjust the kill time to your shift time, up to a maximum of 350 ms. If you would like manual
control over the WOT Shift kill time, start the car and hold down the button on the module and wait for the
LED to begin to blink. Using the chart below, find the number of blinks that corresponds to the kill time that
you want to set. Setting 0 blinks will disable the WOT Shift feature and setting 1 blink will set the automatic kill
time mode. When you have reached the number of blinks that match your desired setting, simply let go of the
button. To confirm, the WOT Box will blink back out the setting you entered.
The WOT Box comes preset for a 2‐step RPM of 4000. To set the 2‐Step RPM, repeat the same procedure
described above, but keep the clutch down during the entire operation. This will signify to the WOT Box that
you want to set the 2‐step RPM and not the WOT Shift kill time. Use the second chart provided below to
match up the desired RPM with the number of blinks. Setting 0 blinks will disable the 2‐Step feature.
Ignition Cut Time Chart ‐ Set with the clutch UP
Blinks Ignition Cut (ms) Blinks Ignition Cut (ms) Blinks Ignition Cut (ms) Blinks Ignition Cut (ms)
0 Disabled 6 125 12 275 18 425
1 Auto (default) 7 150 13 300 19 450
2 25 8 175 14 325 20 475
3 50 9 200 15 350 21 500
4 75 10 225 16 375 22 525
5 100 11 250 17 400 23 550
2‐Step RPM Chart ‐ Set with the clutch DOWN
Blinks RPM Blinks RPM Blinks RPM Blinks RPM
0 Disabled 6 3000 12 4200 18 5400
1 2000 7 3200 13 4400 19 5600
2 2200 8 3400 14 4600 20 5800
3 2400 9 3600 15 4800 21 6000
4 2600 10 3800 16 5000 22 6200
5 2800 11 4000 (default) 17 5200 23 6400
