RESIDENTIAL PRODUCTS

SINGLE STAGE SNOW

ENGINE SERVICE MANUAL
LC168F / LC168FD (163cc)
About this Manual
This service manual was written expressly for Toro service technicians. The Toro Company
has made every effort to make the information in this manual complete and correct. Basic shop
safety knowledge and mechanical/electrical skills are assumed. The Table of Contents lists the
systems and the related topics covered in this manual. An electronic version of this service
manual is available on the Toro Dealer Portal. We are hopeful that you will find this manual a
valuable addition to your service shop. If you have any questions or comments regarding this
manual, please contact us at the following address:

The Toro Company

Residential and Landscape Contractor Service Training Department
8111 Lyndale Avenue South
Bloomington, MN 55420
Chapter 1 – General Service Information 1
Chapter 2 - Engine Service / Maintenance 2
Chapter 3 - Engine Disassembly and Service 3
Chapter 4 - Electrical 4
NOTES:

0
Chapter 1 – General Service Information 1

Safety 2
Service Rules 3
Engine Model / Serial Number Location 3
Engine Fastener Torque Specification 4
General Specifications 5
Engine Specifications 5
Troubleshooting 6

1
Safety

Safety Information

This symbol means WARNING or PERSONAL SAFETY INSTRUCTION – read the instruction because it has
to do with your safety. Failure to comply with the instruction may result in personal injury or even death.
This manual is intended as a service and repair manual only. The safety instructions provided herein are for
troubleshooting, service, and repair of the Toro engine. The Toro operator’s manual contains safety
information and operating tips for safe operating practices.

Avoid Unexpected Engine Start - Turn off engine and disconnect the spark plug before servicing engine.

Avoid Lacerations and Amputations - Stay clear of all moving parts while the engine is running.

Avoid Burns - Do not touch the engine, muffler, or other components which may increase in temperature
during operation, while the unit is running or shortly after it has been running.

Avoid Fires and Explosions - Avoid spilling fuel and never smoke while working with any type of fuel or
lubricant. Wipe up any spilled fuel or oil immediately. Never remove the fuel cap or add fuel when the engine
is running. Always use approved, labeled containers for storing or transporting fuel and lubricants.

Avoid Asphyxiation - Never operate an engine in a confined area without proper ventilation.

Avoid Injury From Batteries - Battery acid is poisonous and can cause burns. Avoid contact with skin, eyes,
and clothing. Battery gases can explode. Keep cigarettes, sparks, and flames away from the battery.

Avoid Injury Due To Inferior Parts - Use only original equipment parts to ensure that important safety
criteria are met.

Avoid Injury To Bystanders - Always clear the area of bystanders before starting or testing power
equipment.

Avoid Injury Due To Projectiles - Always clear the area of sticks, rocks, or any other debris that could be
picked up and thrown by the power equipment.

Avoid Modifications - Never alter or modify any part unless it is a factory approved procedure.

2
Service Rules 1
1. Only use genuine Toro parts and lubrication products.

2. Always install new gaskets, O-rings and seals when assembling engine.

3. Always torque fasteners to specification and in sequence.

4. Always lubricate friction components with clean engine oil or engine assembly lube
when assembling engine.

Engine Model / Serial Number Location

2010-2011 - The engine model and serial number are stamped into the crankcase near the electric starter
mounting position on the side of the engine towards the front of machine (shown below).
2012 - The engine model and serial number are stamped into the crankcase near the rear of the machine.

Engine Model and

Serial Numbers

XXX-XXXX XXXXXXXXXXX
Engine Model Serial Number

3
Engine Fastener Torque Specifications

Torque
Item
Specification

Oil Drain Plug 17 ft-lbs (23 Nm)

Connecting Rod Bolts 8.5 ft-lbs (12 Nm)

Crankcase & Cover Bolts 17.5 ft-lbs (24 Nm)

Valve Lash Lock Nut 11 ft-lbs (15 Nm)

Rocker Arm Studs 22 ft-lbs (30 Nm)

Spark Plug 22 ft-lbs (30 Nm)

Valve Cover Bolts 7 ft-lbs (10 Nm)

Starter Bolts 7 ft-lbs (10 Nm)

Recoil Mounting Bolts 7 ft-lbs (10 Nm)

Cylinder Head Bolt 25 ft-lbs (34 Nm)

Heater Box Nuts 7 ft-lbs (10 Nm)

Flywheel Nut 62.5 ft-lbs (85 Nm)

Ignition Coil Bolts 7 ft-lbs (10 Nm)

Throttle Control Bolts 7 ft-lbs (10 Nm)

Governor Arm Nut 7 ft-lbs (10 Nm)

Muffler / Exhaust to Cylinder Nuts 22 ft-lbs (30 Nm)

Muffler Mounting Plate Bolts 7 ft-lbs (10 Nm)

Standard Torque Values

M5 Bolt / Nut 4.5 ft-lbs (6 Nm)

M6 Bolt / Nut 7.5 ft-lbs (10 Nm)

M8 Bolt / Nut 19 ft-lbs (26 Nm)

M10 Bolt / Nut 28 ft-lbs (38 Nm)

M12 Bolt / Nut 41 ft-lbs (55 Nm)

4
General Specifications 1

MODEL LC168F-1 (Recoil Start) LC168FD-1 (Electric Start)

Engine Type OHV Single Cylinder, Four Stroke, Forced Air Cooling
Displacement (cc) 163
Bore x Stroke (mm) 68 x 45
Compression Ratio 8.5:1
Engine Operating RPM 3550 - 3850 RPM
Oil Capacity 20 oz. (0.6 l)
Fuel Type Unleaded Gasoline, 87 Octane
Ignition System T.C.I Transistorized Magneto
Lubrication System Splash
Cylinder Aluminum with Cast Iron Bore

Engine Specifications

Spark Plug Gap 0.0275 - 0.0314” (0.7-0.8 mm)

Valve Intake Cold 0.0059” (0.15 mm)
Clearance Exhaust Cold 0.0078” (0.20 mm)
Resistance (primary) 1-1.6Ω
Ignition Coil Resistance (secondary) 15.5K Ω ±15%
Gap to Flywheel 0.011- 0.019” (.3-.5 mm)

NOTE: The only internal parts available for this engine are gaskets and seals.

5
Troubleshooting
Hard Starting / Poor Running
- Incorrect Fuel (Level, Age, Octane, Ethanol Content)
- Fuel System Contamination and / or debris in Carburetor
- Incorrect Oil Level
- Spark Plug (Incorrect Gap, Fouled, Loose or Faulty)
- Air Intake System Leaks
- Ignition Coil to Flywheel Gap Incorrect
- Weak / No Spark
- Choke / Linkage
- Operating RPM Incorrect
- Governor Adjustment Incorrect
- Engine Valve Clearance out of Specification
- Low Compression or Excessive Leakdown

Overheating
- Incorrect Oil Level
- Cylinder Head Gasket Leak
- Debris Build-Up Restricting Air Flow

6
Chapter 2 - Engine Service / Maintenance 2

Engine Oil Change Procedure 8

Spark Plug Service 9
Valve Clearance Inspection and Adjustment 10
Engine Governor – Zero Point Setting 11
Engine RPM Adjustment 11
Fuel Filter Replacement 12

7
Engine Oil Change Procedure

1. Run engine to warm engine oil.

2. Remove the ignition key.
NOTE: Ensure fuel system contains no fuel to prevent leakage when engine is tipped.
3. Position oil drain pan under oil drain plug.
4. Remove the oil fill / check cap.
5. Remove the oil drain plug. If necessary, replace drain plug gasket.
6. Tip engine slightly backwards (if necessary) to completely drain the engine oil.
7. Install the oil drain plug - torque to 17 ft-lbs (23 Nm).
8. Add oil through the oil check / fill hole. Wipe the dipstick clean and insert it into the dipstick hole.
NOTE: DO NOT fully install / screw in the dipstick to check the oil.
9. Remove the dipstick and check the oil level – Add oil if needed until the proper oil level is reached.
NOTE: DO NOT overfill the engine oil
10. Fully install and tighten the dipstick.
11. Properly dispose of the used engine oil.

Engine Oil Capacity:

20 oz. (0.6 l)

Engine Oil Type:

API classification of SF,SG, SH, SJ, SL, or higher.

8
Spark Plug Service 2

NOTE: Spark plugs of the wrong size or incorrect heat range can cause severe engine damage.
NOTE: The shrouding, discharge chute and handle may need to be removed to access the spark plug.

High Voltage Ignition Systems can be Dangerous - Use Caution when Servicing Ignition Systems

1. Disconnect the spark plug boot and thoroughly clean the spark plug area.
2. Remove the spark plug from the engine.
3. Inspect the spark plug for excessively worn electrodes, chips or cracks in the insulator, or excessive
deposits.
4. Measure the electrode gap and adjust if necessary. Spark Plug Gap: 0.0275 - 0.0314” (0.7-0.8 mm)
5. Install spark plug and torque to specification - 22 ft-lbs (30 Nm).
6. Fully install the spark plug boot on the plug.

NOTE: Be sure breather tube is routed above the spark plug wire.

Spark Plug

0.0275 - 0.0314”
(0.7-0.8 mm)

Image for reference only

9
Valve Clearance Inspection and Adjustment
NOTE: Valve clearance inspection and adjustment must be done with the engine cold .

1. Rotate engine to TDC (top-dead-center) of the compression stroke.

2. Remove the valve cover. Be sure both valves are completely closed and the decompression arm is not
holding the valve open.

3. Measure the clearance between the rotator and the valve stem with a feeler gauge.

NOTE: Be sure feeler gauge blade is not opening the valve while measuring valve clearance

Intake: 0.0059” (0.15 mm)

Exhaust: 0.0078” (0.20 mm)

4. To adjust valve clearance:

- Hold the rocker arm pivot and loosen the pivot lock nut.
- Turn the rocker arm pivot to obtain the specified clearance.
- Hold the rocker arm pivot and tighten the pivot lock nut to specification - 11 ft-lbs (15 Nm).

5. Recheck the clearance and readjust if necessary.

6. Inspect the valve cover gasket and replace if necessary. Install the cylinder head cover and torque
fasteners to specification - 7.5 ft-lbs (10 Nm).

Rocker Arm

Feeler Gauge
Pivot Lock Nut

Rocker Arm Pivot

10
Engine Governor – Zero Point Setting 2
1. Loosen but do not remove the governor pinch bolt nut (A).
2. Move the governor arm (B) towards the carburetor to fully open the throttle valve. Firmly hold the
governor arm in this position.
3. Rotate the governor arm shaft (C) fully clockwise and secure it in this position with a pair of pliers.
4. Tighten the governor arm pinch bolt (A) and nut to specification - 7.5 ft-lbs (10 Nm).
5. Verify that the governor arm and throttle valve move freely.
6. Start and warm engine.
7. Verify the engine operating RPM is set between 3550 - 3850 RPM.

Engine RPM Adjustment

1. Properly set the governor zero point as shown in this
manual.
D
2. Start and warm engine.
3. Attached an appropriate tachometer to the engine.
4. Adjust engine RPM by turning the High Speed Setting
Screw (D) located above the carburetor asm.

Engine Operating RPM - 3550 - 3850 RPM

11
Fuel Filter and Hose Replacement

- Fuel is Extremely Flammable - Use Extreme Caution When Servicing Fuel System

1. Drain the fuel tank into an approved container.

NOTE: Ensure fuel system contains no fuel to prevent leakage when the fuel filter is replaced.

2. Release the fuel filter / fuel hose clamps (A) and slide them away from the fittings.

3. Remove the fuel filter / hose asm. from the engine.

4. Properly install new fuel filter / hose asm. and hose

clamps (A).

5. Re-fill tank with fresh fuel.

A

6. Verify hose routing and check for leaks.

7. Properly dispose of any unused fuel.

12
Chapter 3 - Engine Disassembly and Service 3

Engine Service – Upper End 14-23

Muffler / Heat Shield Exploded View 14

Heater Box Exploded View 15
Carburetor Mounting 16
Carburetor Exploded View 17
Recoil Asm. Exploded View 18
Starter / Flywheel / Coil Exploded View 19
Cylinder Head Exploded View and Service Information 20
Cylinder Head / Valves Exploded View and Service Information 21
Cylinder Head Specifications 22
Valve Seat Reconditioning 23

Engine Service – Lower End 24-27

Crankcase Exploded View and Information 24

Governor Exploded View 25
Piston / Connecting Rod Exploded View and Information 26
Valve Timing 27

NOTE: The only internal parts available for this engine are gaskets and seals.

13
Engine Service – Upper End
Muffler / Heat Shield Exploded View

Muffler / Exhaust Pipe

22 ft-lbs (30Nm)
7 ft-lbs (10Nm)

Gasket

Muffler Mount Bracket

14
Heater Box Exploded View 3

Wing Nut

Cover

Spacer and Washer Base

Heater Box

7 ft-lbs (10Nm)

Gasket
Note Orientation for Assembly

Up

15
Carburetor Mounting

Cylinder Head

Gasket

Primer Hose

Spacer

Gasket Fuel Hose

Note Orientation for Assembly

7 ft-lbs (10Nm)

16
Carburetor Exploded View 3
.

O-ring

Throttle Shaft Jet

Stop Screw

Choke Lever

Choke Plate

Nozzle

Main Jet
Needle and Asm.
Pin

Gasket

Float
Float Bowl
Exchange
Gasket

Drain Screw
7 ft-lbs (10 Nm)

17
Recoil Asm. Exploded View

Shroud and Recoil Asm.

7 ft-lbs (10 Nm)

Set Screw Spring Clip Spring

Recoil Housing

Guide

Ratchet

Wheel

18
Starter / Flywheel / Coil Exploded View 3

Starter Asm. Blower Shroud

(Optional) Electric Start
Blower Shroud
Recoil Start

7 ft-lbs (10 Nm)

Flywheel

Cup

Ignition Coil Asm.

Side Plate
7 ft-lbs (10 Nm)
Fan

Flywheel Nut
Image for Reference Only 62.5 ft-lbs (85 Nm)

Starter Removal

1. Remove recoil and shroud asm.

2. Remove flywheel with an appropriate puller.
3. Remove the fasteners securing the starter motor to the engine and remove starter asm.

19
Cylinder Head Exploded View and Service Information

Cylinder Head Bolt Torque Sequence:

1. Initially Torque the (4) Cylinder Head Bolts in a Crisscross Pattern to 10 ft-lbs (14 Nm).

2. Evenly Torque the (4) Cylinder Head Bolts in a Crisscross Pattern to 25 ft-lbs (34 Nm).

Spark Plug
Cylinder Head Bolts
25 ft-lbs (34 Nm)

7 ft-lbs (10 Nm)

Dowl

Gasket

Shroud
Valve Cover

Gasket

Cylinder Head

7 ft-lbs (10 Nm)

NOTE: The only internal parts available for this engine are gaskets and seals.

20
 Cylinder Head / Valves Exploded View and Service Information 3

Exhaust Valve

Valve Spring
Retainer

Rotator

Intake Valve

Rocker
Arm
Push Rod
Pivot
Stud
Valve Lash Lock Nut
22 ft-lbs (30 Nm)
11 ft-lbs (15 Nm)

NOTE: The only internal parts available for this engine are gaskets and seals.

21
Valve Seat Width Inspection
Remove carbon deposits from the combustion chamber. Inspect the valve seats for pitting or other damage.

Standard Service limit

0.03149” (0.8mm) 0.07874” (2.0mm)

Cylinder Head Warp Inspection

- Remove carbon deposits from the combustion
chamber. STRAIGHT EDGE

- Clean off any gasket material from the cylinder head surface.

- Check the spark plug hole and valve areas for cracks.

- Check the cylinder head for warpage with a straight FEELER GAUGE
edge and a feeler gauge as shown.

Service Limit 0.00393” (0.10 mm)

NOTE: If this measurement is out of specification, complete engine replacement is required.

The only internal parts available for this engine are gaskets and seals.

22
Valve Seat Reconditioning 3
1. Thoroughly clean the combustion chamber and valve seats to remove carbon deposits.

2. Apply a light coat of Prussian Blue or erasable felt-tipped marker ink to the valve faces.

3. Properly install valves, springs and keepers. Manually open the valves, then and snap them closed
against their seats several times. Be sure the valves do not rotate on the seat. Remove the valve
assemblies. The transferred marking compound will show any area of the seat that is not concentric.

4. Use a 45°cutter to remove enough material to produce a smooth and concentric seat. Follow the valve
seat cutter manufacture’s instructions. Turn the cutter clockwise, never counterclockwise. Continue to
turn the cutter as you lift it from the valve seat.

5. Use a 30°~32° and 60° cutter to narrow and adjust the valve seat so that it contacts the middle of the
valve face. The 30°~32° cutter removes material from the top edge. The 60° cutter removes material from
the bottom edge. Be sure that the width of the finished valve seat is within specification.

6. Lap valves in accordance with valve lapping kit instructions.

7. Clean valve and seat of all lapping compound.

Valve Seat Width

Standard Service Limit
0.03149” (0.8mm) 0.07874” (2.0mm)

CONTACT TOO HIGH

CONTACT TOO LOW

23
 Engine Service – Lower End
Crankcase Exploded View and Service Information

17.5 ft-lbs (24 Nm)

Seal

Bearing
Gasket

Crankshaft

Key
Governor

Bearing

Crankcase Cover Governor

Shaft

Camshaft
8.5 ft-lbs
(12 Nm)

Piston Asm.

Seal

Triangular Mark to Face Down

NOTE: The only internal parts available for this engine are gaskets and seals.

24
Governor Exploded View 3

Clip

Weight

Slider

Governor Gear

Washer

Washer
Pin
Governor
Shaft Clip

Shaft

NOTE: The only internal parts available for this engine are gaskets and seals.

25
 Piston / Connecting Rod Exploded View and Service Information
Second Ring / Gap
Piston Rotation Arrow

Install Piston Ring

Markings “UP”

Top Ring / Gap Oil Rings

Stagger Scraper Rings 8.5 ft-lbs
150°～ 210° from the Oil Ring (12 Nm)

Connecting Rod

Piston Pin

Piston Pin Clip Oil Splash Spoon

Point Down to
Match Piston Arrow

Triangular Mark to Face “DOWN”

Towards Push Rods

Clip Gap
Piston Cut-out

26
Valve Timing 3

Crankshaft
Timing Marks

Camshaft

27
NOTES:

28
Chapter 4 – Electrical System Information 4

Ignition Coil Gap Adjustment 31

Ignition Coil Resistance Inspection 32
Spark Testing 32

29
Ignition Coil Gap Adjustment

High Voltage Ignition Systems can be Dangerous - Use Caution when Servicing Ignition Systems

1. Install the ignition coil and lightly tighten the ignition coil mounting bolts.
2. Rotate engine so ignition coil is aligned with the magnet portion of the flywheel.
3. Insert the feeler gauge between the flywheel and coil.
4. Adjust the ignition coil gap at both side of the coil.
5. Torque the ignition coil mounting fasteners to specification - 7 ft-lbs (10 Nm)

0.011- 0.019”
Ignition Coil Gap
(.3-.5 mm)

Ignition Coil

0.011 – 0.019
(.3-.5mm)
Flywheel

30
Ignition Coil Resistance Inspection 4

Primary Coil
Place Ohm meter leads between the harness connection
lead and the exposed metal coil leg. A
A - Primary Coil Resistance 1.0-1.6 Ω

Secondary Coil
Place Ohm meter leads between exposed metal coil leg
and the spark plug terminal connection. B
B - Secondary Coil Resistance 15.5 KΩ +/- 15%

Image for Reference Only

Spark Testing

- Fuel is Extremely Flammable - Use Extreme Caution When Servicing the Fuel System
- High Voltage Ignition Systems can be Dangerous - Use Caution when Servicing Ignition Systems

1. Remove spark plug boot from the spark plug.

2. Remove the spark plug from the engine.
3. Connect the negative (-) electrode of the spark plug (threaded area) to ground (cylinder head cover).
4. Crank the engine and view the electrode gap. Spark should be present when engine is turning over.
5. Reinstall the spark plug and torque to specification - 22 ft-lbs (30 Nm).
6. Properly install the spark plug boot.

31
 RESIDENTIAL PRODUCTS

Form Number: 492-9230

32