Performance Parts

Service Tool Catalog

for

Truck/Trailer, Container, Transport A/C, Marine

62-03213 Rev L
Service Tool Catalog
Introduction
This service tool catalog identifies service tools used to perform service on transport
refrigeration equipment manufactured by Carrier Transicold. Service tools included in this
catalog are recommended tools that are considered necessary for proper service.
This catalog is broken down into major tool categories listed on page i. Also, this catalog
includes both a pictorial and descriptive reference to most tools listed. This is intended to make
it as simple as possible to find the service tools required.

Ordering Instructions

All orders and inquiries for parts must include:

- Part number
- Description of part as shown
- Quantity required
Address all correspondence for parts to the following address:
Carrier Transicold Division
Performance Parts Group, TR-20
P.O. Box 4805
Syracuse, NY 13221

Fax: (315) 432-3778

email: ppg.customerservice@carrier.utc.com
How to use this manual
Please take a few minutes to read this page. It explains the content and structure of this manual,
which will make it easier to find the tools you need.

Section 1: Compressor and Clutch

This section contains tools used on compressors and clutches, including spanner wrenches,
clutch removal tools, unloader ring pliers, valve pade blank-off kits, sight glass wrenches,
sleeve pullers, bearing pullers, and more.
Section 2: Electrical
This section contains electrical tools, including meters, testers, diagnostic tools, grounding
grounding straps, extractors, crimpers, removal tools, terminals, splice kits, cables, battery
packs, software, software cards, and more.
Section 3: Engine
This section contains tools used on engines, including testers, hose replacements, charts,
adapters, install tools, puller sets, wrenches, meters, lifting tool, allignment rod, and more.

Section 4: Fittings
This section contains fittings, including elbows, caps, quick connectors, Schrader valve cores,
adapters, and more.

Section 5: General Tools

This section contains general tools, including gauges, hoses, strobe lights, testers, heat gun,
thermometers, meters, probes, sensors, sockets, air gap guage tools, seal drivers, driver
tools, wrenches, rivnut install kits, lifting tools, and more.
Section 6: Refrigeration Tools
This section contains refrigeration tools, including manifold gauge sets and accessories,
hoses, gaskets, couplers, o-rings, oil pump, vacuum pump, vacuum gauge, refrigeration
wrenches, refrigerant analyzer, acid test kits, leak detectors, refractomers, and more.
Section 7: Shop Supply, Cleaners and Chemicals
This section contains general shop supplies, including compressor oil, grease, paint, coil
cleaners and sanitizers, sprayers, insulation, leak detectors, flushes, towels, oil test kits, and
more.
Index
Alphabetical and Numerical Index.

i
Section 1 - Compressor and Compressor Clutch

Clutch Tools

Wrench, Spanner for Clutch Armature

Spanner wrench for holding the armature plate on 07‐00240‐01
clutches. The holding pins are adjustable for use on
most industry automotive clutches.

Bearing Driver for Housing (HUB) Mounted Clutch

Rotor installation tool for housing‐mounted clutches. 07‐00241‐00
Used to tap the inner race onto the compressor hub.

Socket, Spanner Nut Large with Grease Fitting

Socket for spanner nut on housing‐mounted clutches.
Used on the following spanner nuts: 34‐01304-00 twin
port compressor, 34‐06083‐00, and 34‐01161‐00. 07‐00242‐01
NOTE: Outside diameter is 3.5”, inside diameter is 2.75”
- where teeth grab on nut is approximately 3” diameter.

Socket, Spanner Nut Small without Grease Fitting

Socket for spanner nut on housing‐mounted clutches.
Used on the 34‐01162‐00 spanner nut. 07‐00242‐02
NOTE: Outside diameter is 2.75” - where the teeth grab
the spanner nut is approx. 2.5” diameter.

Trailer Unit Standby Clutch Adjustment Tool

07-00455-00
Used to adjust the standby clutch shoes on trailer units.

Trailer Unit Standby Clutch Bearing Press Tool

Used to press in the bearing on trailer unit standby 07-00456-00

clutches.

1-1
Section 1 - Compressor and Compressor Clutch
Bolt, Clutch Removal, 7/8‐14X4”
07‐00381‐00
Used to remove the clutch on 05G compressors

Pliers, Unloader Ring

07‐00223‐00
Used to install the unloader valves on hot gas bypass
compressors. Pliers compress piston ring.
Wrench (Special) Compressor Oil Pan
Used to tighten compressors base plate mounting bolts 07‐00267‐01
with compressors installed.

05G Shaft Seal Tool

Used to install new bellows‐style shaft seal on the shaft 07‐00460‐00
of an 05G compressor.

Install Tool, TK Shaft Seal

Used to install the 20‐22‐778 one inch shaft seal on TK 07‐00388‐00
compressors.

05G Lip Seal Install Tool

07‐00471‐00
Used to drive new 05G lip seal into the seal cover plate.

Filter, Felt Sock for Clean-Up, 05G Compressors

Filter (suction sock) for cleaning up systems with solid 58‐00869‐00
contaminants. Package of 5.

Filter, Felt Sock for Clean-Up 05K Compressors

Filter (suction sock) for cleaning up systems with solid
contaminants. Package of 5.
58‐04165‐00
NOTE: PPG no longer offers the adapter for the York
style compressor “sock adapter” (14-60043-00) per
Truck Engineering Rouen.

1-2
Section 1 - Compressor and Compressor Clutch

Vise Grip Holder

Used for holding motor leads when replacing a terminal 07‐00264‐00
block on 06D compressors.

Pliers, Crimping, 06D Terminals

Used to crimp the motor leads into the terminal block on 07‐00263‐00
06D compressors.

Kit, Valve Pad Blank-Off, Unloader Head Suction

Cut-Off
17‐13004‐00
Cap off plate for two‐bolt, 1‐3/4” center line service
valves.

Kit, Valve Pad Blank-Off, 4-Bolt, 2-1/2” Centerline

Cap‐off plate for four‐bolt, 2‐1/2” centerline service 17‐13006‐00
valves.

Kit, Valve Pad Blank-Off, 2-Bolt, 1-5/8” Centerline

Cap‐off plate for two‐bolt, 1‐5/8” center line service 17‐13008‐00
valves.

Kit, Valve Pad Blank-Off, Unloader Head Suction

Cut-Off
17‐21056‐00
Cap-off plate for the piston on suction cut‐off unloading
cylinder heads.

Kit, Valve Pad Blank-Off, Unloader Head HGBP

Cap-off plate for the unloader valve on hot gas bypass 17‐55013‐00
or suction cut-off unloading cylinder heads.

Compressor Oil Refractometer

Used to measure the amount of residual mineral oil in a 07-00316-00
system being changed to POE oil.

1-3
Section 1 - Compressor and Compressor Clutch

Wrench – Sight Glass

This improved tool (redesigned and hardened) is used
07‐00450‐00
to install and remove the oil sight glass on 05G, 05K,
06D, 5D, 05D, 5F, AND 5H compressors.

Wrench – Sight Glass

Sight glass installation tool used on Thermo King 20‐204‐244
compressors.

APU - Quick Start Compressor

Used to test-start small 115VAC hermetic compressors
up to 5HP. This kit was set up for use with APU 07‐00494‐00
compressors, but will also work with other hermetic
compressors if appropriate amperage fuse is used.

APU - Fuse, Resettable, 20 Amp

Used in the 07‐00494‐00 Quick Start kit for Comfort Pro
APU compressors.
07‐00494‐10
NOTE: This fuse was only sized for use on APU
compressors. For all others, check the LRA and follow
instructions.

5F, 5H Main Bearing Puller

Used to pull the main bearings from a 5F/5H
07-00346-00
compressor. Has a new alignment hub for assured
alignment and new acme threads for pull strength.

1-4
Section 1 - Compressor and Compressor Clutch

Marine - Sleeve Puller (5F Compressors)

07‐00394‐00
Used to pull the sleeves out of 5F compressor cylinders

Marine - Sleeve Puller (5H Compressors)

07‐00395‐00
Used to pull the sleeves out of 5H compressor cylinders

Container - Terminal Box Tool – Container Scroll

Compressor
07‐00436‐00
Used to remove and replace container unit scroll
compressor terminal box

Container - Air Compressor Tool Kit

Tools for rebuilding Container CA unit air compressor 18‐00099‐40
18‐00099.

1-5
 Section 2 - Electrical

Tools and Meters

Meter, Megohmeter 07-00502-00

Also known as a “Megger ,” this meter is used to

test motor winding insulation integrity on the
Vector generator and all larger winding motors.

Case, Universal Megohmeter

Overall Width 9.5 inches, Overall Height 7.0

inches, Overall Depth 2.0 inches 07-00502-10

Multimeter, Digital – Pen Type

This is a small probe‐style multimeter, designed
to be used with one hand. This feature is helpful
when measuring in small, hard‐to‐get‐to areas.
Resistance to 34 MΩ
Continuity beeper
3400-count digital display plus analog
bar graph
Auto power off
UL 3111-1 listed
Includes alligator clip, ground test lead,
spare probe tip and installed batteries
3 3.4-digit LCD Display

Functional Specifications
DC Voltage 07‐00262‐02
- Ranges: 340 mV, 3.4, 34, 340 V, 600 V
- Accuracy: ± (0.5 % rdg + 2 dgt)
- Resolution: 0.1 mV in 3.4 V range
- Input Impedance: 340 mV range: >100
- MΩ Other ranges: 10 MΩ

AC Voltage (50-500 Hz)

- Ranges: 3.4 V, 34, 340, 600 V
- Accuracy: ± (1.5 % rdg + 8 dgt)
- Resolution: 0.1 mV in 3.4 V range
- Input Impedance: 10 MΩ

2-1
Section 2 - Electrical

Multimeter, Digital
This meter allows the technician to analyze
electrical components ranging from basic
devices to highly sophisticated solid state
controllers. It features an analog and digital
display to test changing or stable signals along
with audible continuity. A continuous tone
signals continuity; a beep signals a forward
biased diode or transistor. Test leads and
07‐00243‐10
protective holster included.

Voltage DC: Range: 6.000V - 1000V

Voltage AC: Range: 600.0 mV-1000V
Amps AC: Range: 60.00 mA Ð 10A
Amps DC: Range: 60.00 mA Ð 10A
Resistance: Range: 600.0 Ω - 50 MΩ
Capacitance: Range: 1nF- 9,999 µF
Frequency: Range: 99.99Hz- 99.99kHz

Test Leads (Right Angle)

For use with 07‐00243‐10 meter
07‐00243‐01

Multimeter, Digital - Wavetek

A digital multi-meter with heavy‐duty features
for rugged protection from mishaps and
adverse environments. One single selector
switch makes it easier to use and saves time by
enabling you to go directly to the function and
range you seek. Ranges in AC/DC voltage and
current along with Ohm readings meet all your
needs. Case included. 07‐00228‐00

Voltage DC: 200mV up to 1500VDC

Voltage AC 200mV up to 1000VAC
AC/DC Current: 200uA up to 2A
Resistance: 200ohm up to 2M-ohm
Diode Test: Range 0 to 2V
Current 20mA$20%
Temperature -

2-2
 Section 2 - Electrical

Kit, Test Leads

For use with 07‐00228‐00 meter. Can also be 07‐00230‐00
used with the 07-00243-10.

AC Current Clamp
This accessory extends the AC current
measurement capability of the P/N 07‐00228 or
CTD P/N 07‐00243 multimeter to 150 amperes
without breaking the circuit under test. The 07‐00229‐00
1000:1 current transformation allows direct
reading in amperes when used with the 200 mA
AC current range of the multimeter.

50A Single Bank AGM Battery Charger

Used to fully charge the AGM battery using a 07-00498-00

three step charging profile.

Battery Tester, Heavy Duty Handheld

Used to rapidly, precisely diagnose bad
batteries individually or in a pack. The unit also 07-00499-00
analyzes vehicle starting and charging
systems.

Temperature Tester - 4‐Lead

07‐00504‐00

Accessories Included:
4 K type probes with lead wraps
2 AAA batteries

2-3
Section 2 - Electrical

Temperature Tester – Spare Lead

4-foot K-type probes with lead wraps for use 07-00504-01

with the 07-00504-00 tester.

Temperature Tester – Soft Case

A soft case for use with 07-00504-00 07-00504-02

temperature tester and probes.

Tachometer, Laser, RPM

Used to read RPMs on rotating devices. 07‐00488‐01

Strobe Light
Used to set and check engine and compressor
speed. Can be used to freeze motion of pulleys, 07‐00486‐00
fan blades, etc. This strobe is a replacement for
part number 07‐00206‐00.

Tester, ML2I/ML3

Used to determine the integrity of the ML2i and 07‐00428‐00SV

ML3 microprocessors.

Tester, Micro
Used in place of the standard Trailer
microprocessor to test the circuits and 07‐00290‐01
components the microprocessor control.
(Instruction Sheet 62‐90258‐00).

DataReader (Container)

Includes DataReader, battery, and cable 12‐50377‐01/2.5

Cable part number – 22-01743-00

Diagnostic Tool, Cab Command Cable

Used to diagnose the cab command cable on 07‐00440‐00

30/40/50S and 30/40/50X truck units.

2-4
 Section 2 - Electrical

APX Micro Service Harness

Used to check voltage leaving micro. Can also
07-00515-00
be used in conjunction with 07-00375-00SV to
drive the valves on Trailer refrigeration units.

Tester, Stepper Motor Drive

Used to check and/or operate the stepper
motor on container units and XTC trailer units. 07‐00375‐00SV
This tool is also used to drive the EVXV open
and closed for service diagnosis during
troubleshooting.

Individual Harness for CSMV (Suction

Modulating Valve SMV)
07‐00375‐10
Used on the 07‐00375‐00SV tester.

Individual Harness for EVXV (Electronic

Expansion Valve EXV) 07‐00375‐11
Used on the 07‐00375‐00SV tester.

Stepper Jumper Assembly

Container jumper cable for microprocessor and 07‐00408‐00

stepper motor driver 07-00375-00SV.

Kit, Static Dissipate

A work surface designed to prevent
electrostatic discharge from damaging 07‐00277‐00
solid‐state electronic devices and components
during service.

Strap, Grounding
A wrist strap grounding to prevent electrostatic 07‐00304‐00
discharge from damaging solid‐state electronic
devices and components during service.

2-5
Section 2 - Electrical

Extractor (EPROM)
07‐00297‐00
Extractor for EPROM on microprocessors.

Inserter (EPROM)
07‐00298‐00
Inserter for EPROM on microprocessors.

Extractor, EPROM, I‐30S

Designed to extract male and female mini‐fit sr. 07‐60048‐00

terminals from their appropriate
connectors/housings.

40S/50S and 40X/50X Micro Connector Pin

07‐60090‐00
Tool

Extractor Pin
Pin extractor for Packard terminals (connector
07‐00400‐00
models Metri‐pack 280, Metri‐pack 480,
Metri‐pack 630, and Metri‐pack 800).

Extractor Pin (AMP Connector)

For removal of terminal connector pins from
07‐00254‐00
connectors used with auto‐start and
microprocessor harnesses.
Terminal Tool (Removing Packard
Terminals in Thermistor Part #12‐00452‐00)
- Advanced Micro
07‐00387‐00
Used to remove the terminals from the
12‐00452‐00 thermistor connector. Also used
with Weatherpack terminals (male and female).
Extractor, ML‐2, ML‐2i and ML‐3 Connector
Metri‐Pack 150, 280, GT150, GT280, 280
tangless, 280 buss bar, 630 pull to seat, lamp 07‐00329‐00
socket B1 and W3, and Metri‐Pack 800
electrical connectors.

2-
 Section 2 - Electrical

Crimper, Micro Pin

07‐00268‐00
Crimper for micro pin on Container unit.

Crimper, Metripack ML‐2, ML‐2i and ML‐3

Connectors
Unsealed 150 Metripack, 150.1 and 150.2 Pull 07‐00330‐00
to seat Core and insulation

Crimper, Weatherpack
Used with Weatherpack connectors and
terminal pins 14 to 20 gauge. 07‐00370‐00

Crimper, AMP Unsealed

All‐purpose crimper for AMP terminals. for wire 07‐00401‐00

size 20‐14 AWG (core and insulation), 10-12
core only

Crimper, Unsealed
Used on Vector generator power leads.
07‐00496‐00

Crimper, Weatherpack
This crimper is used on the Metri pack sealed
150 and 280 series core and insulation. 07-00519-00
22-14awg

Wire Crimper, MAC Tools

MAC Tools Part
Crimper can be used on various size Packard Number: TCT1028
and Amp connectors.

2-
Section 2 - Electrical

Terminal Removal Tool Kit

Kit used to remove terminals and reinstall new 07‐00397‐00
crimped terminals Includes all the 07‐00397
dash numbers. (‐01 through ‐12)

Universal Hand Crimp Tool

Hand crimp tool, Deutsch connectors, and 07‐00397‐02
ML‐2, Ml‐2i and ML‐3 connectors.

Terminal Removal Tool

07‐00397‐01
Removal tool, Deutsch connectors

Removal Tool, Blue

Wire size 16‐18 gauge, Deutsch connectors. 07‐00397‐03
Primarily used on Multi‐Temp units.

Removal Tool, Yellow

Wire size 12 gauge Deutsch connectors. 07‐00397‐04
Primarily used on Multi‐Temp units.

Removal Tool, Green

Wire size 14‐18 gauge Deutsch connectors. 07‐00397‐05
Primarily used on Multi‐Temp units.

Join Terminal 14-16 Gauge

Deutsch connectors. Used on 1st generation 07‐00397‐06
Multi-Temps (10‐pin plug) Deutch HD10

Socket Terminal,14-16 Gauge 07-00397-07

Deutsch connectors.

2-
 Section 2 - Electrical

Join Terminal 14-18 Gauge

22-01613-14
Deutsch connectors

Socket Terminal 14-18 Gauge

Deutsch connectors - Superseded by 22-01613-15
22‐01613‐15

Pin Terminal, 12-Gauge

07‐00397‐10
Deutsch connectors

Socket Terminal 12‐14 Gauge

07‐00397‐11
Deutsch connectors

Cavity Plug - 12‐16 Gauge

07‐00397‐12
Deutsch connectors

2-9
Section 2 - Electrical

Light Bulbs
For use with previously offered Temperature
16‐03004‐00
Controller/Diode Board Test Module
07‐00208‐00. Package of 5.

Socket Terminal, Connector EC - (A-K),

(L-Y)
22‐01777‐03
Female terminal for 22‐01777‐00SV and
22‐01777‐01SV microprocessor connectors.

Fast Splice Kit, Cable Repair

For 10 AWG and 11 gauge. Uses lug instead of
22-50396-00PK5
butt connectors. Shore power cables. Best with
cable diameters of approximately 3/4 inch.

Fast Splice Kit, Cable Repair

For 10 AWG and 11 gauge. Uses lug instead of
22-50396-00PK25
butt connectors. Shore power cables. Best with
cable diameters of approximately ¾ inch.

Splice Kit, Power Cable Repair

(Without Filler)
For 10 AWG and 11 gauge. Butt Splices. 22-50397-00
Shore power cables. Best with cable diameters
of approximately ¾ inch.

2-10
 Section 2 - Electrical

Splice Kit, Power Cable Repair

(With Filler)
For 10 AWG and 11 gauge. Butt Splices. 22-50398-00
Shore-power cables. Best with cable diameters
of approximately 3/4 inch.

Card Drive, PC (Parallel Port)

07‐00438‐00
Used to reprogram software cards

Card Drive, PC USB Port

07‐00439‐00
Used to reprogram software cards

Jumper, Config (Advance Micro)

Config Mode Jumper - White Wire. Used to put 22‐50180‐00
Advance micro into Configuration

Jumper, PC Mode (Advance Micro)

PC Mode Jumper - Green Wire. Allows 22‐50180‐01
Advance micro to power up without turning on
the SROS switch.

Cable, Monitor Program

Used to connect a PC 9‐pin serial (COM1) port 22‐01690‐00

to the 3‐pin Packard serial port on a Summit
micro (Supra, Ultra, Ultima, Extra, Solara, etc.).

Download Cable, 6-Foot

Download data from Container units and Trailer

DataLink with Advance micro to a PC. Used 22-01737-00
with 12‐00543 and 12-50150-10 printers and
other applications.

2-11
Section 2 - Electrical

Download Cable, 20-Foot

Download data from Container units and Trailer 22‐01737‐04

DataLink with Advance micro to a PC. Used
with 12‐00543 printers and other applications.

Download Cable, W Maersk Veam

Connector

Used to download data from the unit 22-01737-01

DataCorder Veam to Deutsch. Use with
22-01737-00.

Download Cable Palm Top

Used to download data from the unit 22-01737-02

DataCorder to a palm top.

Download Cable, PC, Container

Used to connect to the MA connector on 22-01737-06

Container controller to download to PC,
DataReader, etc.

Download Cable

Used between a PC and the APX micro.

22-04253-00 (6’)
Available in 6 and 20-foot lengths.
22-04253-20 (20’)

High Speed USB to Serial Adapter RS232

Interface - Used with Tru-Tech/Tru-View

 USA-19HS high-speed USB to serial 07-00503-00

adapter
 3-foot USB device cable
 CD with driver software and user guide

2-12
 Section 2 - Electrical
Splitter Harness, Satellite Power

This harness is a SAT-PWR (aka OC2 on older

Vectors and European units) splitter. It plugs
into the SAT-PWR connector on the reefer 22-50420-00
harness and allows 2 SAT-PWR connections.
Total amperage for two additional items added
to this harness should not exceed 3.75 A.
PTS12-060

40S/50S and 40X/50X Software Upload Kit 76‐61011‐00

12-00543-10SV

Printers NO LONGER OFFERED.

Only Replacement Parts and Accessories

available.

12-50150-10SV

Replacement Paper Roll, Pack of 5

12‐50150‐01
Paper for the 12‐50150‐10SV printer

Paper Rolls, Pack of 5

Replacement paper for portable printers 12‐00543‐01

(12‐00543‐00 and 12‐00543‐10)

2-13
Section 2 - Electrical

Battery Pack, Rechargeable

NI-Cad rechargeable battery pack used on the 12‐00543‐02

portable printer (12‐00543‐00 and ‐10).

Adapter, 120 VAC

Used to power the portable printer 12‐00543‐03

(12‐00543‐00 and ‐10) from a 120VAC power
source.

Adapter, 12 VDC Vehicle

Used to power the portable printer 12‐00543‐04

(12‐00543‐00) from a vehicle.

Software and PC Cards

Protective Case
58-50109-00
Used to protect PCMCIA cards.

Card, Download, 7-Unit Capacity, NAO

Used to quickly download data from Advance 12‐00503‐50

microprocessors.

Card, Option, DataTrak, NAO, 5-Click

Five‐click DataTrak option card. Used to

activate the DataTrak (remote communications 12‐00505‐53
for satellite) option in the Advance
microprocessor.

2-14
 Section 2 - Electrical

Card, Option, DataTrak, NAO, 10-Click

10‐click DataTrak option card. Used to activate 12‐00505‐52

the DataTrak (remote communications for
satellite) option in the Advance microprocessor.

Card, Option, DataTrak, NAO, 100-Click

100‐click DataTrak option card. Used to

activate the DataTrak (remote communications 12‐00505‐55
for satellite) option in the Advance
microprocessor.

Card, Configuration, Advance

Microprocessor, NAO

Used to install either a single configuration OR

IntelliSet settings on to an Advance
microprocessor. The card can be used multiple
times with no limitation on the number. 12‐00506‐50
Customer configuration files or IntelliSet files
that are available on the Carrier Transicold
Information Center can be written to the card
using the ReeferManager program.

Card, Option, IntelliSet, NAO, 5-Click

Five‐click IntelliSet Option Card. Used to 12‐00505‐71

activate the IntelliSet Option in the Advance
Microprocessor.

Card, IntelliSet Option, NAO, 10-Click

10‐Click IntelliSet option card. Used to activate 12‐00505‐70

the IntelliSet option in the Advance
microprocessor.

2-15
Section 2 - Electrical

Card, Program, Advance Microprocessor,

NAO

Used to quickly install new software into 12‐00504‐50

Advance microprocessor. Can be updated to
latest software version using Reefer Manager
(latest version will be supplied).

CARD, Program, ML3 Controller Software

and Configuration

Used to quickly install new software into 12‐00594

Container ML3 microprocessors (latest version
will be supplied).

Card, DataBank Download

Used to download Container ML3 12‐00615

microprocessors (latest version will be
supplied).

APX USB Universal - This USB flash drive 12-00734-00

interfaces with Tru-Tech to perform the
following functions:

 Software upgrades
 Data recorder downloads
 Configuration, IntelliSet, and
Maintenance set file uploads
DataTrak 5 click (license) USB flash drive
12-00734-01
DataTrak 10 click (license) USB flash drive
(Both the -01 and -02 enable the DataTrak 12-00734-02
telematics option) - See Bulletin PTS13-047

Tru-Tech / Tru-View Program – Advance

Micros Next generation of service software
after Reefer Manager. Must download from NA N/A
Truck Trailer Information center – Questions
contact Service Engineering.

2-16
 Section 2 - Electrical
Software, DataLINE

The DataLine for Windows kit includes: 07‐00421‐00

- Software installation CD (1)
- Installation floppy disks (approximately 15)
- D User's Guide - CTD publications P/N T‐303
License, DataLINE
Additional DataLINE license. 07‐00426‐00

Software, Reefer Manager and Reports

For use with Windows 95/98/ME /2000/XP.
Used to set up and download Advance and
Summit microprocessor and DataLink data
12‐00616
recorders. For more information refer to service
bulletin SER04‐40.
NOTE: This program replaces Monitor Program
12‐00351‐06SV and does everything the
Monitor Program does and more.

DataCold 500R
Used on truck units 79‐60598‐20

DataCold 500T
Used on trailer units 79‐60598‐00

Red Insulating Varnish

Red glyptol varnish used on alternator studs. 07-00479‐00

This varnish is usually painted on with a brush.
Sold in a 2-ounce bottle.

2-
 Section 3 - Engine

Tester, Inject Nozzle

07-00140-00
Used to check and adjust the fuel Injectors in diesel
engines.

Adapter Injector Line (Accessory for 07-00140-00)

07-00036-00
Adapter line for tester inject nozzle. Accessory for tester
inject nozzle. (P/N 07-00140-00)

Tester Inject Nozzle Replacement Bowl (Accessory

07-00140-10
for 07-00140-00)

Compression Test (Diesel Engines 150-850PSI)

Kit comes with compression tester, handle, high-pressure
tester hose assembly, fitting to go from the injector
adapter to the high pressure tester hose, replacement 07-00179-01
cards, and an instruction CD.
NOTE: The following accessories/adapters (07-50005-02
and 07-00179-02 through -10) are used with this item.

Hose Replacement, Hose Assembly (Accessory for

07-00179-08
07-00179-01 compression tester)

3-1
 Section 3 - Engine

Adapter, Injector to Tester (Accessory for

07-00179-09
07-00179-01 compression tester)

Chart Holder – Orange Plastic (Accessory for

07-00179-01 compression tester)
07-50005-00
Used to hold the compression charts on the compression
tester 07-00179-01.

Charts, 10-40 Bar (Accessory for 07-00179-01

07-00179-04
compression tester)

Charts, 150-850PSI (Accessory for 07-00179-01

07-00179-07
compression tester)

Compression Test Adapter Tier 4 engines

07-00484-00
Used with (07-00179-01) to check compression through
the injector hole.

Adapter, Mercedes 0M636 (Accessory for

07-00179-03
07-00179-01 compression tester)

Adapter, Kubota 10mm Glow Plug (Accessory for

07-00179-01 compression tester) 07-00179-05

3-2
 Section 3 - Engine

Adapter, Compression Tester 8mm Glow Plug

(Accessory for 07-00179-01 compression tester) 07-00179-10

Adapter, Kubota CT4-114 Engine (Accessory for

07-00179-06
07-00179-01 compression tester)

Sleeve, Installer, Perkins Front Crankshaft Pulley

Used to correctly install wear sleeve on Perkins front
crankshaft pulley. 07-00227-00

Front Seal Install Tool, Used on 4-Cylinder Kubota

engines,

NOTE: Kubota does not offer a Rear Seal Install Tool. 07-00239-00

Used to install front seal (GEARCASE) on Kubota

4-cylinder engines.

Rear Main Wear Sleeve Install Tool

07-00521-00
Used to install the 25-37385-02 wear sleeves on rear of
crankshaft. 4 Cylinder Kubota.

Socket, Injector
07-00224-00
Socket for injector removal for Kubota IDI engines.

Injector Puller Set

Used on Kubota DI engines. Comes with two adapters so
it can be used on the old “DI” pencil-style injectors and the
DI low emissions engines. Old part numbers were: 07-00517-00
07-00249-00, 07-00458-00.

3-3
 Section 3 - Engine

Carbon Ring Installation Tool, Kubota DI

07-00250-00
Used to aid in the installation of the carbon ring seal in
pencil type DI injectors.

Socket, Water Temperature Sender (Advance Micro

Units)

Used to remove the Water Temperature Sender on Purchase

Advance Units. 3/4” slotted, deep well socket. Must from Snap-On
purchase locally or from Snap-On dealer (Snap-On part
number: S6155).

Crowfoot Wrench, New Water Temperature Sensor

07-00520-00
Tier 4 units, 14mm

Wrench, Davco Filter

07-00423-00
Used to remove and install the Davco fuel filter.

Meter, Coolant Refractometer

Used for testing integrity of glycol and features an 07-00435-00

illuminated refractometer. (USES: EG = ethylene glycol,
PG = propylene glycol).

Coolant Hose Lubricant

02-50010-00
Used with Interference-fit coolant hoses on trailer units.

3-4
 Section 3 - Engine

Coolant Bottle Test Adapter

Used to pressure test new pressurized coolant bottles on 07-00468-00

trailer units. It is to be used with a standard radiator
pressure tester.

Coolant Bottle Test Adapter

Used with a radiator pressure tester (stant or equivalent) 07-00469-00

to test the coolant bottle cap. Used on newer units with
pressurized coolant bottle.

Main Bearing Install Tool

Used to install the main bearing on the newer, low 07-00472-00

emission engines (starting with serial number 3S00001).

Main Bearing Extract Tool

Used to extract the main bearing of the new four-cylinder, 07-00473-00

low emission Kubota engine (starting with serial number
3S00001).

Main Bearing Install Tool

Used to install main bearing on the older four-cylinder 07-00474-00

Kubota engines (prior to serial number 3S00001).

Main Bearing Extract Tool

Used to extract the main bearing on the older 07-00475-00

four-cylinder Kubota engines (prior to serial number
3S00001).

3-5
 Section 3 - Engine

Crank Pulley Impact Socket

Used on Kubota crankshaft pulley nut. 1-13/16” (46mm)

deep well impact socket. SIM-583

NOTE: Must purchase locally from Snap-On or another

impact socket supplier.

Removal Bracket, Vector Generator

Used to rest the generator on during generator removal SKM-5670
on Vector trailer units.

Engine Platform Tool

Used to rest engine on during swing to remove Vector 86-04751-00
generator.

Oil Drain Tool, Vector Units

Used to drain the oil from the engine on Vector Units. 68-15763-00
Often used with bracket part number 68-15706-00.

Oil Drain Tool X2, X4 Belt Drive Units

Used to drain the oil from the engine on (X2/X4) trailer

units. Often used with bracket number 68-15706-00.

68-15763-01

3-6
 Section 3 - Engine

Tachometer, Laser, RPM

Used to read RPMs on rotating devices. 07-00488-01

Strobe Light
Used to set and check engine and compressor speed.
Can be used to freeze motion of pulleys, fan blades, etc. 07-00486-00
This strobe is a replacement for part number
07-00206-00.

Flywheel Locking Tool

Used on Vector trailer units to prevent the engine from
turning while working on the generator. 07-60083-00

Alignment Rods, Vector Generator, 3 pack

07-60121-00
Used on Vector trailer units to remove/install the
generator on the engine.

Lifting Tool, Vector, Generator

Used on Vector trailer units as a generator service tool. 07-60085-02
Compatible with all Vector Generators.
Locking Ear and Nut
Used on 07-60085-02. It is designed to be offered as a
replacement part, but also as an option to upgrade the
07-60085-50
older -00 and or/-01 tools to make them the latest
mandatory -02 tool.

Shim, Vector Generator Service

Used to protect generator windings during 54-00630-25

service/shipping.

3-7
 Section 4 - Fittings

Fitting, Male 1/4” NPT X Male 1/4” Flare Access

06DA-403-844
Port with Schrader

7/16-20 Male Straight Thread O-Ring x ¼” Male

Access Schrader 0TB0889
Access fitting

Fitting, Male 1/8” NPT X Male 1/4” Flare Access

Port with Schrader 17-13010-00

Cap, 1/4” Service Valve Gauge Port (Should not be

used on Schrader Type Ports)
40-00086-04
Acorn style gauge port cap. NOT FOR USE ON
SCHRADER TYPE PORTS.

Cap, 1/4” Flare (For use on Schrader Type Ports)

For use on SCHRADER type gage ports (includes DD19CA061
rubber O-Ring/gasket)

Cap, 1/4” Flare, Plastic

This is a 1/4” plastic cap used to cap off the Shrader 58-60232-00
access fitting after service. It comes with an o-ring
which is not sold separately.

Cap, 3/8” Flare

40-00086-06
Used on trailer unit king valves.

Core, Schrader Valve

Schrader valve core used in the standard 1/4” Schrader 14-00351-00
fittings. Typically used on the older CFC/HCFC access
fittings such as 40-01124-00. Package of 10.

4-1
 Section 4 - Fittings
Schrader Core, 3/8”,134A
Standard Schrader core for 134A access fittings. 40-60087-01
Primarily used for Manuli in-line fittings, but can also be
used with other access valves.

Adapter, R134A (LO)

This is a 134A adapter that mounts on a 1/4” flare, low
side. 40-01184-00
NOTE: Replacement o-ring is part number
40-01184-50.

Adapter, 1/4” NPT X 1/2” Acme 07-00301-00

Male 1/4” NPT X Female 7/16” Straight Thread

07-00319-00
O-Ring

Plug, 7/16”-20 Straight Thread, O-Ring 17-44037-00

Plug, 9/16”-18 Straight Thread, O-Ring 17-44706-00

90 Elbow Swivel Female 7/16-20 Straight Thread

40-00519-00
O-Ring X M13

90 Elbow Swivel Female 7/16-20 Straight Thread

40-00519-01
O-Ring X M15

Quick Connector Nipple (R134A Low Side) X M13

40-00520-00
(with Cap)

4-2
 Section 4 - Fittings

Quick Connector Nipple (R134A Low Side) X M15

40-00520-01
(with Cap)

Cap, Low Side R134A Quick Connect Fitting

40-00520-02

Cap, High Side R134A Quick Connect Fitting

40-00520-03

90 Elbow Swivel R134A Male M13 Straight Thread x

40-00523-00
Female M13

90 Elbow Swivel R134A Male M15 Straight Thread x

40-00523-01
Female M15

90 Elbow Male ¼” NPT x Female M13 R134A Low

40-00524-00
Side

90 Elbow Male 1/8” NPT x Female M15 R134A High

Side 40-00524-01

Male 9/16-18 Straight Thread O-Ring x Female ¼”

40-00528-00
NPT

Male 7/16”-20 Straight Thread O-Ring x Female ¼”

40-00528-02
NPT

4-3
 Section 4 - Fittings

Coupling, R134A
40-00529-00
7/16” X 20 coupling size by M8 quick connect

Tee, Female, ¼” Flare Swivel x Male ¼: Flare x LS

40-00545-00
Quick Connect

Schrader Fitting Body, ¼” Male Flare, Braze-in

This Schrader can be brazed into most refrigerant lines
40-01124-00
and used as an access fitting for service. it is 1/4” flare
by 1/4” ID or 3/8” OD sweat.

90 Elbow Male 9/16 – 18 Straight Thread O-Ring x

40-01166-00
Female ¼” NPT

90 Elbow Male 7/16 – 18 Straight Thread O-Ring x

Female ¼” NPT 40-01166-01
NOTE: O-ring not sold separately.

Tee, Snubber, 1/8” NPT x 1/8” NPTF

79-00965-00
Pressure switch mounting tee (Trailer products)

Adapter, Female, ¼” x Quick Connect (High Side)

AC302-438

Adapter, Female, ¼” x Quick Connect (Low Side)

AC302-439
with Cap

Adapter, 90 Degree Female ¼” Flare x Quick

AC302-440
Connect (High Side)

4-4
 Section 4 - Fittings

Adapter, 90 Degree Female ¼” Flare x Quick

AC302-441
Connect (Low Side)

Retrofit Kit, Service Ports for 134A Fittings

AC302-458
(Automotive)

4-5
 Section 5 - General

Gauge, Magnehelic
Used to accurately set the defrost air switch, which 07-00177-00
initiates defrost cycle. Includes carrying case, fittings
and aspirator.

Hose, Replacement, 9-Foot

07-00177-05
Replacement hose for the 07-00177-00.

Aspirator
Replacement aspirator for Magnehelic gauge (part 07-00177-01
number 07-00177-00).

Strobe Light
Used to set and check engine and compressor speed.
Can be used to freeze motion of pulleys, fan blades, 07-00486-00
etc. This strobe is a replacement for part number
07-00206-00.

Flashtube, Xenon (for 07-00206-00 Strobe Light)

Replacement bulb for strobe light (part number 07-00206-01
07-00206).

Belt Alignment Tool - Laser

Laser alignment tool quickly identifies the two most

common types of pulley misalignment - parallel offset 07-00463-00
and angular - that reduce belt and pulley service life
and produce unwanted noise.

Gauge, Belt Tension

Used to adjust belt tension of all non-cogged V-belts. 07-00203-00
Proper belt tension increases both bearing and belt life.

Tester, Belt Tension

07-00253-00
Used to test belt tension.

5-1
 Section 5 - General

Rubber Band
Replacement part for belt tension tester (part number 07-00253-01
07-00253-00).
Heat Gun, 120V-50/60hz - 570-1000 degrees
Fahrenheit
This heat gun replaces part number 07-00256-00,
which is no longer available from the supplier. It is used 07-00487-00
to heat shrink-tubing on wiring connectors and splices.
It can also be used to defrost coils, although caution
should be used as the high temperature setting will
actually melt the aluminum fins.

Thermometer, Pocket
Bi-metal thermometer for measuring temperature from 07-00261-00
-40 to +160 degrees Fahrenheit.

Thermometer, Digital, Pocket (Degrees Fahrenheit)

This is a straight digital (thermistor type) pocket 07-00485-00
thermometer with a 3-foot probe. Reads in degrees
Fahrenheit only.

Thermometer, Digital, Pocket (Degrees

Centigrade)
This is a straight digital (thermistor type) pocket 07-60111-00
thermometer with a 3-foot probe. Reads in degrees
Centigrade only.

5-2
 Section 5 - General

Thermometer, Non-Contact
Used for checking temperatures at a safe distance.
Aim the thermometer and pull the trigger for a
temperature reading of 0 to 750° F (-18 to 400° C)
without the danger of moving parts or getting burned.
07-00324-00
Power 9V battery with low power indicator.
Features: ±2% Accuracy and LCD backlight.
This meter is more advanced than the 07-00323-00
with Max -min - average temperature and high or low
audio/visual alarm.

Thermometer, Infrared, Non-Contact

This infrared non-contact thermometer replaces
07-00323.
 Infrared Thermometer
 Certificate of Calibration:Yes
 Temperature Measuring Range:-32° C to 600°
07-00478-00
C
 Temperature Accuracy +/-:2 F
 Response Time:500mS
 Accuracy:+/-1%
Battery Size Code:9V RoHS Compliant: NA

Multi-meter, Digital
This meter allows the technician to analyze electrical
components ranging from basic devices to highly
sophisticated solid state controllers. It features an
analog and digital display to test changing or stable
07‐00243‐10
signals along with audible continuity. A continuous
tone signals continuity; a beep signals a forward
biased diode or transistor. Test leads and protective
holster included.

Temperature Probe (-40° F to 1,500° F)

This adapter allows the 07-00243-10 Fluke multimeter

to read temperature. It can read in degrees F or C. This
adapter comes with one bead probe and can convert
any digital multimeter with a 10mohm input into a
thermometer. Accepts type “K” thermocouple probes 07-00425-00
and sensors. Accuracy: 0.5%

5-3
 Section 5 - General

Temperature Probe (-40° F to 1,500° F)

To be used with adapter part number 07-00425-00.

This temperature probe is used in conjunction with the
Fluke Multi-meter 07-00243-10. It is a universal probe
that can measure air temperatures from -40° F to 07-00424-00
1500° F, including high exhaust temperatures. This
temp probe uses the type “K” thermocouple which is
the most accurate and quickest responding in the in the
industry today.

Sensor, Thermometer
Sensor used with the old 12-50039-00 and
12-50040-00 light bar thermometers. 12-00569-51
Sensor, Thermometer – 10-Foot 12-00569-52
Sensor, Thermometer – 18-Foot

Leads, 50-Foot
For use with previously offered Simpson Temperature 07-00013-02
Tester, 07-00013-00.

Case, Meter, For use with 07-00013-00

For use with previously offered Simpson Temperature 07-00015-00
Tester, 07-00013-00.

Rod for Servicing Self-Adjusting Idlers on

FrigiKing Truck Units
07-00276-00
Rod for servicing self-adjusting idlers on FrigiKing truck
units.

Barrier, Flame
07-00302-00
Used to isolate heat when working in tight quarters.

5-4
 Section 5 - General

Socket, Spanner for Ultra Gearbox Fan clutch

07-00303-03
Spanner socket for Ultra gearbox clutch spanner nut.
Clutch mounted on gearbox.

Socket, Spanner for Extra XT Fan clutch

Spanner socket used to remove the Fan clutch 07-00303-02

spanner nut. Clutch mounted on fan shaft.

Air Gap Gauge Tool (ULTRA Clutch)

Used to measure the air gap on the 90 degree gear box 07-00360-01
clutch.

Air Gap Gauge Tool, Clutch

Used on the following trailer unit models: Ultima, Extra 07-00432-00
XT, Ultra XT, Ultra XTC, and Ultima XTC. Similar in
design to part number 07-00360-01.

Seal Pilot, Small Ultra Gearbox

07-00308-00
Pilot for small seal on Ultra gearbox.

5-5
 Section 5 - General

Seal Pilot, Large Ultra Gearbox

07-00309-00
Pilot for large seal on Ultra gearbox.

Sleeve Tool, Seal

Used to guide the fan shaft cap end seal during 07-00339-00
installation.
Sleeve Tool, Seal
Used to guide the fan shaft flange end seal during 07-00341-00
installation

Seal Driver, Small Ultra Gearbox

07-00310-00
Driver for small seal on the output shaft (clutch side) of
the Ultra gearbox.

Seal Driver, Large Ultra Gearbox

07-00311-00
Driver for large seal on the input shaft (drive end) of the
Ultra gearbox.

Driver Tool, Seal

Used to drive the fan shaft cap end seal during 07-00340-00
installation.

Driver Tool, Seal

Used to drive the fan shaft flange end seal during 07-00342-00
installation.

5-6
 Section 5 - General

Driver, Bearing Plate

07-00343-00
Aids in the installation of the fan shaft bearing cone

Driver, Bearing
07-00344-00
Aids in the installation of the fan shaft bearing cup.

Guide Tool, Installation

07-00357-00
Aids in the installation of the fan shaft excluders.

Gauge, Sheave (34 Degree)

07-00364-00
Used to determine wear of sheaves

Wrench, Spanner, Fan, Clutch

Used to hold the armature during fan clutch removal. 07-00396-01
Used on Ultima and Extra XT units

Wrench, Spanner, Solenoid Evap

Used to remove the stem on the remote evaporator 07-00476-00
liquid solenoid valve. Due to space restrictions, this
tool attaches to a 1/2 inch drive socket ratchet.

Condenser Fan Removal Tool

Used to remove part number 38-00503-00 condenser 07-00399-00

fan on 69NT40-511 units.

5-7
 Section 5 - General

Crowfoot Wrench - 1 1/8”

3/8” drive open end crowfoot wrench, used on NT scroll 07-00409-00

economizer valve.

Crowfoot Wrench - 1 3/8”

3/8” drive open end crowfoot wrench; used on NT scroll 07-00410-00

suction and discharge valves.

Crowfoot Wrench - 2 1/8”

3/8” drive open end crowfoot wrench; used on NT 07-00411-00

Scroll - Suction Modulation Valve.

Bit, Torx Driver

Container battery unlock tool, used to remove the 07-00418-00

TORX screws on the display to access the lithium
back-up battery.

Mirror, Inspection

Replacement for discontinued part number

07-00437-00. This mirror is the same design except 07-00477-00
that it now telescopes from 10 to 14 inches in length
instead of 15 inches. It has a diameter of 2.25 inches.

5-8
 Section 5 - General
*

Rivnut Tool, Frame Rework

This tool is for use on unit frame rework kits

07-00449-00
(76-00768-00 and -01). It is used in conjunction with
the 07-00448-00 drill bit.

Rivnut Install Kit Imperial

Includes rugged thread setter tool and an assortment
of fractional Klik Poly-Nuts:
 12 each 8-32, 10-24, 10-32
07-00447-00
 8 each 1/4"-20, and six 5/16"-18 threads.
 Equipped with the required nosepieces and
mandrels for setting the above sizes.
Set is packaged in a storage case.
Rivnut Install Kit Metric
Metric version of the HP650 with metric poly-nuts,
including:
 25 each 4 and 5mm
 15 each 6mm 07-00451-00
 10 each 8mm threads.
 Thread setter tool, required nosepieces, and
mandrels.
Set is packaged in a storage case.
Tap, Thread, Left-Handed

This thread tap tool is used to clean out the threads in

the end of the fan shaft (50-00232-##) during service
on XT units.
NOTE: The fan shaft (50-00232-##) also has external 07-00453-00
threads that hold the clutch on with a spanner nut.
These threads can be cleaned and chased using a
thread die, 1-9/16-18NS-3, left handed purchased
locally.

Lifting Device, 20/30S and “X” Units

This is a 3-way hoist used to lift 20S, X and 30S, X 07-60049-00

units during installation.

5-9
 Section 5 - General

Lifting Device, 40S/50S and X Units

07-60091-00
This is a hoist used to lift 40S, X/50S, X units during
installation.

Lifting Tool, Vector, Generator 07-60085-02

Used on Vector trailer units as a generator service tool.
Locking Ear and Nut
Used on 07-60085-02. It is designed to be offered as a
07-60085-50
replacement part, but also as an option to upgrade the
older -00 and or/-01 tools to make them the latest
mandatory -02 tool.

Removal Bracket, Vector Generator

Used to rest the generator on during generator removal SKM-5670
for Vector trailer units.

Engine Platform Tool

Used to rest engine on during swing to remove Vector 86-04751-00
generator.

Threaded Rod, Vector Generator Removal

Used on Vector trailer units to remove/install the
07-60121-00
generator on the engine.

Flywheel Locking Tool

Used on Vector trailer units to prevent the engine from
turning while working on the generator. 07-60083-00

5-10
 Section 5 - General

Shim, Vector Generator Service

Used to protect generator windings during 54-00630-25
service/shipping.

Rain Cap – Flip Top

30-00210-00
This universal flip top rain cap is used to keep debris
and moisture from entering the exhaust pipe.

Anti-Siphon Tank Insert

SNOW
FLAKE
SIDE HOLES
FOR ADDED
These 1.875 inch ID tank inserts are designed to foil
DESIGN FLOW even the most determined thief. Made from the finest
quality materials, they offer the following key benefits:
LOCKING
TAB
 Easy snap-in installation 65-50001-00
 Self-locking when snapped in
 60 gallon-per-minute flow rate
 No hassling with keys and locking fuel caps
 Low cost

Epoxy Repair Kit for Evaporator Pods

This can be used on fiberglass or to repair the

composite/plastic pods. Two-part resin epoxy, one roll
76-50063-00
fiberglass cloth 3” wide by 3’.

5-11
Section 6 - Refrigeration

Manifold Gauge Set

Used on R134a systems. Gauges read in PSI.
Hoses are barrier type hoses with quick connect
07-00294-00
couplers on the high and low side hoses and 1/2
acme fitting on the center hose.

Manifold Gauge Set

Used on R134A systems. Gauges read in bar.
Hoses are barrier type hoses with quick connect
couplers on the high and low side hoses and 1/2 07-00294-05
Acme fitting on the center hose. Includes: Hose
Set 07-00307-00, Coupler 07-00307-04 and
coupler 07-00307-05.

Manifold Gauge Set, Kit CFC

Used on R-12, R-22, R-500 and R-502 systems.
Hoses are 60 inch barrier type hoses with anti-
07-00314-00
blowback valves on the service ends. Includes:
Handwheels 07-00237-04, Gauge 07-00237-05,
Gauge 07-00237-06, Hose Set 58-04030-00

Handwheel Package
Hand wheel set for most older gauges.
07-00237-04
Replacement wheels for the 07-00294-05 and
older Robinair sets.

Low Side Compound Gauge for CTD P/N

07-00294-00
07-00294-01
Low side compound gauge for P/N 07-00294-
00. Gauge reads in PSI.

High Side Pressure Gauge for CTD P/N

07-00294-00
07-00294-00
High side gauge for P/N 07-00294-00. Gauge
reads in PSI.

6-1
Section 6 - Refrigeration

Compound Gauge for CTD P/N

07-00314-00 CFC
07-00237-05
Low side compound gauge for P/N
07-00314-00.

Compound Gauge for CTD P/N

07-00314-00 CFC
07-00237-06
High side compound gauge for P/N
07-00314-00.

Hose Set
Replacement hose set for manifold gauge set 58-04030-00
(P/N 07-00314-00).

Hose Set (Consists of 07-00307-01, -02, -03)

Replacement hose set for manifold gauge sets
(P/N 07-00294-00 and 07-00294-05). Includes 07-00307-00
Hoses, 07-00307-01, 07-00307-02 and 07-
00307-03.

Hose, Yellow
72 inches long, barrier type. Replacement hose
07-00307-01
for use on center connection of manifold gauge
sets (P/N 07-00294-00 and 07-00294-05).

6-2
Section 6 - Refrigeration

Hose, Red
72 inches long, barrier type. Replacement hose
for use on high side connection of manifold 07-00307-02
gauge sets (P/N 07-00294-00 and 07-00294-
05).

Hose, Blue
72 inches long, barrier type. Replacement hose
for use on low side connection of manifold
gauge sets (P/N 07-00294-00 and 07-00294- 07-00307-03
05).

Gasket
Replacements for manifold gauge hoses 1/4 07-00237-12
inch. Package of 6.

Gasket
Replacements for manifold gauge hoses 3/8 07-00237-13
inch. Package of 6.

Coupler, Quick-Connect, Gauge Hose Low

Side R134A
Quick connect couplers for low side hose on
07-00307-04
gauge set (P/N 07-00294-00 and 07-00294-05).
Uses gasket 07-00331-00 and O-ring
42-50017-00.

6-3
Section 6 - Refrigeration

Coupler, Quick-Connect, Gauge Hose High

Side R134A
Quick connect couplers for high side hose on
gauge set (P/N 07-00294-00 and 07-00294-05). 07-00307-05
Uses Gasket 07-00331-00 and O-ring 42-50018-
00

Gasket
These are replacement O-rings for the hose side
07-00331-00
of couplers 07-00307-04 or 07-00307-05.
Package of 6.

O-Rings (Low Side, smaller than high side)

These are replacement O-rings for the
42-50017-00
connection side of quick-connect coupler 07-
00307-04. Package of 10.

O-Rings, (High Side, bigger than low side)

These are replacement O-rings for the
42-50018-00
connection side of quick-connect coupler
07-00307-05. Package of 10.

Vacuum Gauge, Digital (Microns) 07-00414-00

Used to measure deep vacuums in microns,
down to 10 microns, for accurate dehydration
vacuums.
Features:
 2.5 X 3 inch size
 Fitted with 6-foot lead
07-00414-01
Sensor, Replacement
Used on the 07-00414-00 digital vacuum gauge.

Vacuum Gauge, Electronic (Microns)

Good to 1 micron and has an input/output fitting

for the vacuum hoses. Fittings on meter are 07-60132-00
input - 1/4 inch male flare. Output fitting is also
1/4 inch male.

6-4
Section 6 - Refrigeration

Vacuum Pump, Dual Voltage / Dual

Frequency, 110-115/220-240 VAC 50/60 HZ
 6 CFM (free air)
 2 stage rotary vane type
 1/2 horsepower
 Intake fitting 1/4 MFL and 1/2 Acme 07-00176-11
 Plug not provided
 Pre-wired for 220/240 VAC (change wire
terminations in accordance with motor
nameplate for 110-115 volt applications)

Heavy Duty Plus II Charging/Vacuum Hose

3/8 inch ID heavy duty hose x 1/4 inch female
07-00237-10
flare. Permeation resistant (Plus II) barrier,
working pressure 750psi; 3000psi burst.

Oil Pump - 1 to 5 Gallons

07-00516-00
Used to manually add refrigeration oil to
refrigeration systems

Refrigeration Wrench
Refrigeration wrench for service valve stems 07-00238-00
3/16, ¼, 5/16, and 3/8.

Refrigeration Wrench, Offset

Refrigeration wrench, offset for service valve 07-00238-01
stems 3/16, 1/4, 5/16, and 3/8.

Acid Test Kit, Mineral and Synthetic Oil

Acid test kit for mineral and alkyl benzene 07-00260-00
compressor oils.

6-5
Section 6 - Refrigeration

Acid Test Kit, Polyolester POE Oil

07-00337-00
Acid test kit for POE compressor oils.

Total Test Acid Test Kits (6) Kits

Comes with six kits under the part number. Each
kit includes the case, a tool and a pack of five 07-00265-01
blue tubes for testing CFC (R-12, 22, 500, 502)
refrigerants.

(6) Packages of Replacement Blue Tubes

Replacement tubes for the TotalTest kit
(P/N 07-00265-01). Each pack includes five blue 07-00266-00
tubes, two test tube caps, and a replacement o-
ring for the instrument.

Refrigerant Analyzer

An R40 capable refrigerant analyzer used to

07-00518-00
analyze 134A systems and helps to keep
dangerous counterfeit refrigerants out of the
refrigerant supply chain.

Leak Detector
Leak detector for R-12, R-22, R-500, R-502, 07-00295-00
R134A, R404A refrigerants.

6-6
Section 6 - Refrigeration

Element
07-00296-00
Replacement kit for leak detector 07-00295-00.

Head Assembly, Halide Leak Detector 07-00259-00

Used to find chlorine-based refrigerant leaks

Copper Reactor for Halide Torch 07-00259-20

Copper Reactor Plate use with 07-00259-00

Leak Detector
Bubble leak detector used to locate refrigerant 07-50017-00
leaks.

Programmable Charging/Recovery Meter

Three display modes -- Lbs/oz; Decimal Lbs.;
Kilograms
 Allows automatic Charging or Recovery
operations.
 Color-coded keypad controls
 Very High Resolution -- 0.2 oz./0.010
Lbs./4 grams.
 Can be used with all refrigerants.
 Advanced Charge and Recovery. Modes
– uses tare weight and max. capacity of 07-00315-00
cylinder to calculate maximum
Charge/Recovery available
 User Programmable memory for up to 99
different stored values.
 “Repeat” charge features removable
platform and control box with prop
stand/hanging hook.
 Compact Design -- completely portable,
battery powered with low battery
indicator.

6-7
Section 6 - Refrigeration

Temperature Tester - 4‐Lead

07‐00504‐00

Accessories Included:
4 K type probes w lead wraps
2 AAA batteries

Temperature Tester – Spare Lead

4-foot K-type probes with lead wraps for use 07-00504-01

with the 07-00504-00 tester.

Temperature Tester – Soft Case

A soft case for use with 07-00504-00 07-00504-02

temperature tester and probes

Temperature Probe – 15-Foot Sealed

15-foot sealed temperature probe for use with 07-00462-01
the old 07-00462 meter.

6-8
Section 6 - Refrigeration

Temperature Probe, Air, 15-Foot Sealed

15-foot air temperature probe for use with the 07-00462-03
old 07-00462 meter.

Meter, Refractometer for Compressor Oil

Used to measure the amount of residual mineral 07-00316-00
oil in a system being changed to POE oil.

Suction Filter Kit

Designed for use with the 05G compressor and
contains all parts needed to cycle the suction
gas though a replaceable element suction line
07-00379-00
filter. Kit includes two elements - a pleated filter
used for solid particulate removal only and a
solid core acid removal element designed for
particulate, water, and acid removal.

Filter, Solid Core - Acid

Replacement filter used in the 14-50056-00
suction filter shell supplied with the Suction Filter 14-50054-00
Kit part number 07-00379-00. It is the activated
core for acid removal within the system.

Filter, Regular Core

Replacement filter used in the 14-50056-00
suction filter shell supplied with the Suction Filter 14-50055-00
Kit part number 07-00379-00. It is the regular
core for non-acidic filtering.

6-9
Section 6 - Refrigeration

Suction Filter Shell

This is the filter shell that comes in the 14-50056-00
07-00379-00 Suction Filter Kit.

Filter Housing – Internal

This is the internal filter housing used inside the
filter shell to hold the filter cores in the
14-50056-00. 14-50056-01

Oil Filter Kit, 05G Compressor

The Compressor Oil Filter kit, designed for use
with 05G, 05K and 06D compressors with gear
oil pumps, comes with an extremely fine micron
filter and a bracket to mount the filter below the
compressor. The filter is used as a bypass from
the compressor oil pump and will not affect
compressor lubrication, even if it becomes
plugged. 07-00380-00

The compressor circulates oil through the filter

at a rate of approximately one gallon per minute,
making oil clean up time very fast and efficient.
Experience has shown that even very
contaminated systems will clean up within one
to two hours of unit operation with the kit(s)
installed.

Kit, Hose Cutter, Crimper, Expander and

Plastic Case
07-60117-00
Used to cut, expand, and install fittings on black
Carrier refrigerant hose.

Pliers, Crimping
(Part of kit number 07-60117-00)
07-60117-10
Used to connect the fitting clamps on the black
Carrier refrigerant hose.

6-10
Section 6 - Refrigeration

Pliers, Fitting Assembly, EZ Clip

Used to connect the fitting to hose on Aeroquip 07-00467-00
fittings.

Tool, Fitting Insertion (for black Carrier hose)

Specially developed for after-sales service, this
tool can only be used to insert fittings in hoses.
The tool is shipped with a set of jaws, an
adaptor set, a spring set, and the technical
procedure. The components can also be
purchased separately: 07-60133-00

 07-60133-10 – Set of jaws

 07-60133-20 – Set of adaptors
 07-60133-30 – Set of springs

Note: Not designed for or applied to APU.

Tool, Pinch Off (CU Tube)

Pinch off tool for process tubes. Primarily setup
for the Matson hermetic container unit however 07-00385-00
will work on all process tubes and pinching
requirements so tubing can be brazed.

Valve, Piercing
Used to gain access to the refrigerant circuit for
07-00386-00
gauge reading, charging, evacuation, recovery,
etc.

Dispensing Gun, Static Mixing

(used with Kit 76-50084-200SV)
Application gun needed to apply Durabond 07-00391-00
epoxy used for repair of inserts on container
composite control boxes.

6-11
Section 6 - Refrigeration
Refrigerant System Quick Check Kit
Used with procedures outlined in instruction
sheet 98-50554-00 (R-22/R404A Quick Check
Refrigeration System Troubleshooting
Procedure), It is designed to test the major
07-50006-00
components used in the Carrier Transicold
trailer refrigeration units (Phoenix Advantage,
Phoenix Ultra, and Optima) that use refrigerants
R-22 or R404A. Kit contains the 22-50190-00
wire harness and instruction sheet 98-50554-00.

Hex Head Security Stepper Valve

This is a specially designed hex bit (Allen
07-00434-00
wrench) which fits the adjustment screw on the
stepper valve (14-00263-00) piston.

Magnet, Check Valve Tool – Discharge

Designed to open the seat on the X series trailer
14-00331-10
unit discharge check valve during inert brazing
and unit evacuation.

Magnet, Container EXV PrimeLINE

Designed to manually open the electronic
14-00393-52
expansion valve during service or
troubleshooting.

Magnet, Container EXV NaturaLINE

Designed to manually open the electronic
14-00396-20
expansion valve during service or
troubleshooting.

Magnet, Operating Solenoid

This magnet tool is used to open solenoid
valves manually when no power is available, or
07-00512-00
during service. Inside diameter is 18mm or 0.75
inch

6-12
Section 6 - Refrigeration

Wrench, Spanner Unloader System

Designed to fit securely onto the 17-40417-00
unloader valve. Tool was developed as a 07-00459-00
stronger alternative to the powdered metal tool
supplied with the 17-40418 unloader kit.

Refrigerant Recovery Unit – 115 VAC. DIABLO-115V

3/4HP Compressor capable of direct liquid.

Refrigerant Recovery Unit – 230/240VAC DIABLO-240V

3/4HP Compressor capable of direct liquid

Schrader Core, 3/8 inch, 134A

Standard Schrader core for 134A access fittings.
Primarily used for Manuli in-line fittings, but can
40-60087-01
also be used with other access valves. See
fittings (Section 4) for other Schrader and
special fittings.

6-13
Section 7 - Shop Supply, Cleaners, and Chemicals

Oil, Compressor - Synthetic (150)

Synthetic 150 for R-12, R-22, R-500 and R-502
Typical Use Trailer Units. 07-00274-00

Package Size: Six one-gallon containers

Oil, Compressor - Mineral (150)

Mineral Oil 150 for R-12, R-22, and R-500
Typical Use Trailer Units. 07-00275-00

Package Size: Six one-gallon containers

Oil, Compressor (S-100)

Synthetic 100 for R-12, R-22, R-500 and R-502
Typical Use Truck Units. 07-00270-00

Package Size: 12 one-quart bottles

Oil, Compressor - (SW20)

POE 22 for R134A
Typical Use Container 07-00292-00

Package Size: 12 34-ounce cans

Oil, Compressor - (SW20)

POE 22 for R134A
Typical Use Container 07-00292-01

Package Size: Six one-gallon cans

7-1
Section 7 - Shop Supply, Cleaners, and Chemicals

07-00317-00
1 gallon
Oil, Compressor, (PEOE 68)

POE 68 for 134A and 404A. Typical uses are for

05G and 05K compressors. Available in 1 gallon
07-00317-
or pack of 6.
00PK6
6 gallons

Oil, Compressor – 50 PAG, R1A, 1 Quart can

Used in R134A refrigerant bus AC circuits with
Seltec/Valeo/Zexel/Ice/Tama TM series
compressors. Sold in a one quart, screw top 46-50006-00
metal can.

Package Size: One-quart can

Oil Compressor (S-68)

POE 22 for R-134A and R-404A Typical use is

07-00318-00
on truck refrigeration units.

Package Size: 12 ounce cans

Oil, Compressor S-68

Synthetic 68 for R-12, R-22 and R-500, R-502.

07-00320-00
Typical use, truck units.

Package Size: Pack of (6) 1 quart bottles.

Oil, 32ST
Mobile Arctic 32 ST polyolester (POE) oil for
R-134. Commonly used for container units with
scroll compressors (69NT40-531 for example) 07-00427-00

Package Size: One quart can

7-2
Section 7 - Shop Supply, Cleaners, and Chemicals

Oil, Castrol E-68

POE Oil Typical use: 5F, 5H, 05K, 06D and 06E
compressors for Marine units. P903-1701

NOTE: Used to be part number 07-00405-00.

Oil, Refrigerant (Soltex VG 68) Gallon

For ALKYLBENZENE applications
07-00430-00
Package Size: One gallon container

Oil, Compressor (5GS)

Mineral Oil 500 for R502. Typical Use Truck

07-00325-00
Units Rotary Compressors.

Package Size: 12 one-quart bottles

Oil, Vacuum Pump

07-00328-00
Package Size: 12 one-quart bottles

Oil, Compressor – POE 35 TK Trailer units

with 404A, 1 gallon
07-00349-00
POE 35 for R134A and R404A
Thermo King trailer units

Oil, Compressor – POE 32 TK Container

Units. Case of 4 gallons
07-00354-00
POE 32 for R134A and R404A
Thermo King container units
Package Size: Case of (4) 1 gallon bottles

7-3
Section 7 - Shop Supply, Cleaners, and Chemicals

Oil, Synthetic Gear Box 75W-90 (Ultra gear

case)
07-00359-00
Synthetic gear oil 75W-- 90 for the 90 degree
trailer unit gear box.
Package Size: (12), 12 oz bottles

Oil, Fan shaft , Trailer

Used in the lubrication of fan shafts. 07-00373-00

Package Size: Package of (12), 8oz bottles.

Oil, Compressor 300 Mineral

Mineral Oil 300 for R-12, R-22, and R-500
07-00377-00
Typical Use Large Bus

Grease, Heat Conductive Sealer

02-00010-00
Used to improve conduction of heat at TXV bulb
location.

Grease, N-2

For use on TK clutches. 46-50002-00

Package Size: 14 ounce tube

7-4
Section 7 - Shop Supply, Cleaners, and Chemicals

Grease, Lithium Base

Grease, lithium base for use on linear solenoids.

This grease is not affected by moisture, heat, or 07-00245-00
cold.

Package Size: 5.3 ounce tube

Sikaflex Caulk Sealant

A high-quality multi-purpose non-sag 1-c

polyurethane sealant that cures on exposure to
02-00067-01
atmospheric humidity to form a durable
elastomer.

Package Size: 10.3 ounce tube

Loctite 609
02-00130-01
Primary usage is on clutch hub threads in
Truck/Trailer.

Sealant, Pipe Fittings on 134A Units

Sealant for pipe fittings on units using HFC

Refrigerants. (R134A and R404A). 50ml tube. 07-00345-00

Package Size: 50 ml tube

Red Insulating Varnish

Red glyptal varnish used to seal alternator studs

and other electrical generating and power studs. 07-00479-00
Prevents corrosion. Brush not included

Package Size: 2-ounce bottle

7-5
Section 7 - Shop Supply, Cleaners, and Chemicals

HumiSeal

Used to seal the back of printed circuit boards

from moisture. 07-50001-00

Package Size: 12-ounce can

Gas, Calibration

Used as a standard to calibrate the sensors on

controlled atmosphere units. 07-00322-00

Package Size: 14-ounce bottle

Adapter Fitting for Calibration Gas

07-00322-02
Used with 07-00322-00 calibration gas.

Smoke Bomb
Used to test seal integrity and airflow of 16-00037-00
refrigeration unit ductwork and air systems.

Paint, Sea Spray Green

Unit Touch-Up paint for miscellaneous 38 series
units. Also used on: 38GR, CC, CB 48, 50, 58
PH23GL012
units.

Package Size: 16-ounce can

Paint, Touch-Up, Seahorse Blue

This spray paint is used to touch up Seahorse
units and other CTD marine blue units. 07-00480-00

Package Size: 16-ounce can

7-6
Section 7 - Shop Supply, Cleaners, and Chemicals

Paint, Touch-Up, (05G and Kubota)

This spray paint is used to touch up scratches
on 05G compressors and Kubota engines. 07-00420-00

Package Size: 16-ounce can

Paint, Touch-Up, Horizon Green

This spray paint is used to touch up scratches
on 19D and 19C units. PH23GH017

Package Size: 16-ounce can

Paint, Blue, Compressor

Hull blue compressor paint used on

CTD container units. There are two cans of 76-00397-01
primer and two cans of the epoxy paint.

Package Size: One pint can

Paint, Horizon Green

Unit touch-up paint for 19 series units PH23GH012

Package Size: 16-ounce can

Coil Cleaner – Evap Foam No Rinse

High performance, heavy-duty detergent.

Foaming, no rinse, aerosol evaporator coil NU4171-75
cleaner, foams out dirt! Six 18-ounce cans.

Package Size: Six 18-ounce cans

Coil Cleaner, Citrus

Citrus type coil cleaner will help clean coils, but

07-00313-00
not corrode the coil and is easy on unit paint.

Package Size: Four one-gallon bottles

7-7
Section 7 - Shop Supply, Cleaners, and Chemicals

Coil Cleaner, Cal-Brite

Low pH or acid-based product developed for

cleaning evaporator and condenser coils, safe NU4133-08
yet aggressive!

Package Size: Four one-gallon bottles.

Coil Cleaner, Cal-Shield with Teflon

Contains Teflon to shield and protect finned

NU4148-08
cooling and heating coils from dirt and corrosion.

Package Size: Four one-gallon jugs

Coil Cleaner, Cal-Shield with Teflon

Contains Teflon to shield and protect finned

NU4148-32
cooling and heating coils from dirt and corrosion.

Package Size: Six one-quart bottles

Coil Cleaner, Tri-Pow’r

Alkaline detergent/degreaser for cleaning air

NU4371-88
cooled condensers, evaporator coils, permanent
filters, fan blades, motors, etc.

Package Size: Four one-gallon jugs

Coil Cleaner – Nu-Brite

Revolutionary strong, foaming condenser coil

NU4291-08
cleaner, Alkaline. The Acid alternative!

Package Size: Four one-gallon jugs

Coil Cleaner – Nu-Brite

2.5 Gallon
Revolutionary strong, foaming condenser coil
NU4291-05
cleaner, Alkaline. The Acid alternative!
55 Gallon
NU4291-01
Package Size: 2.5 gallon pail or 55 gallon

7-8
Section 7 - Shop Supply, Cleaners, and Chemicals

Coil Sanitizer – Bio-Fresh CD

A concentrated, ready to use bacteriostat-

NU4126-34
fungistat-deodorizer formulated for
use in HVACR systems.

Package Size: 12 one-quart bottles

Coil Sanitizer – Bio-Fresh CD

A concentrated, ready to use bacteriostat-

NU4126-38
fungistat-deodorizer formulated for use in
HVACR systems.

Package Size: Four one-gallon jugs

Coil Sanitizer – PanPads ACP

Condensate drain pads prevent bacteria and
NU4295-34
slime in pans. Combats a broad spectrum of
harmful bacteria.

Sprayer, No. 50P Poly

Pump sprayer for coil cleaners, half-gallon
capacity.
NU4770-00
Package Size: One sprayer

Sprayer, No. 220CP

Pump sprayer for coil cleaners, 2 gallon
capacity. NU4771-30

Package Size: One sprayer

7-9
Section 7 - Shop Supply, Cleaners, and Chemicals

Sprayer, No. 300CP

Pump sprayer for coil cleaners, 2 gallon
capacity. NU4772-00

Package Size: One sprayer

Sprayer, Coil Gun

Hose end sprayer with mixing valve to dilute coil
cleaners. NU4774-00

Package Size: One gun

Insulation – Insulation Slugs

Thumbing grade slugs for plugging holes.
NU4216-92
Package Size: 24 two-pound boxes

Insulation – Cork Insulation Tape

Insulation tape for wrapping refrigerant lines.
NU4217-W3
Package Size: 12 – 2” x 30’ Rolls

Insulation – Foam Insulation Tape

Insulation tape for wrapping refrigerant lines.
NU4218-W3
Package Size: 12 – 2” x 30’ Rolls

Insulation – Nu-Foam Insulation Foam

A triple expanding foam that insulates as well as
9 oz
seals cracks, crevices and other openings.
NU4293-04
Created for refrigeration, air conditioning and
20 oz
heating pipes and tubing.
NU4293-75
Package Size: 9 oz or 20 oz cans

7-10
Section 7 - Shop Supply, Cleaners, and Chemicals

Gas leak Detectors – Cal-Blue

Gas leak detector.
NU4182-08
Package Size: Four one-gallon jugs

Gas leak Detectors – Cal-Blue

Gas leak detector with trigger spray.
NU4182-24
Package Size: 12 one-quart bottles

Gas leak Detectors – Cal-Blue

Gas leak detector with dauber in cap.
NU4182-53
Package Size: 24 6-ounce bottles

Flush - Rx11 Flush, 2-in1 Display

Rx11 flushing solvent for burnouts and oil
removal. Two cylinder pack with valve. NU4300-10

Package Size: One two-cylinder pack.

Flush - Rx11 Flush

Rx11 flushing solvent for burnouts and oil
removal. Single cylinder.
NU4300-11
Package Size: Four single cylinders

7-11
Section 7 - Shop Supply, Cleaners, and Chemicals

Flush – Rx11 Flush

Rx11 flushing solvent for burnouts and oil
removal. 50 ton capacity. NU4300-15

Package Size: 15 pound cylinder

Flush – Rx11 Flush Fitting Assembly

Access valve for single Rx11 cylinders.
NU4300-99
Package Size: One valve

Flush – Rx Acid Scavenger

Acid neutralizer for refrigeration oil. 2oz treats
up to one gallon of contaminated oil. NU4301-02

Package Size: Six two-ounce bottles

Hand Towels – Kleen-N-Toss

Scrubbing hand cleaning towels with special
cleanser.
NU4230-72
Package Size: Six 72-towel buckets

Oil Test Kit – Phase III

Refrigeration oil acid test kit.
NU4320-W8
Package Size: 24 kits

7-12
 Alphabetical Index
40S/50S amd 40X/50X Micro Connector Pin Tool 2-6 APX USB Universal 2-16
40S/50S amd 40X/50X Software Upload Kit 2-13 Aspirator 5-1
50A Single Bank AGM Batter Charger 2-3 Barrier, Flame 5-4
5F, 5H Main Bearing Puller 1-4 Battery Pack, Rechargeable 2-14
(6) Packages of Replacement Blue Tubes 6-6 Battery Tester, Heavy Duty Handheld 2-3
7/16-20 Male Straight Thread O-Ring x ¼” Male
Access Schrader 4-1 Bearing Driver for HUB Mounted Clutches 1-1
90 Elbow Male ¼” NPT x Female M13 R134A Low
Side 4-3 Belt Alignment Tool - Laser 5-1
90 Elbow Male 1/8” NPT x Female M15 R134A High
Side 4-3 Bit, Torx Driver 5-8
90 Elbow Male 7/16 – 18 Straight Thread O-Ring 4-4 Bolt, Clultch Removal, 7/8 x 14 x 4 1-2
90 Elbow Male 9/16 – 18 Straight Thread O-Ring 4-4 Cable, DataReader 2-4
90 Elbow Swivel Female 7/16-20 Straight Thread 4-2 Cable, Monitor Program 2-11
90 Elbow Swivel Female 7/16-20 Straight Thread 4-2 Cap, 1/4” Flare 4-1
90 Elbow Swivel R134A Male M13 Straight Thread x
Female M13 4-3 Cap, 1/4” Flare, Plastic 4-1
90 Elbow Swivel R134A Male M15 Straight Thread x
Female M15 4-3 Cap, 1/4” Service Valve Gauge Port 4-1
AC Current Clamp 2-3 Cap, 3/8” Flare 4-1
AC302-438 4-4 Cap, High Side R134A Quick Connect Fitting 4-3
AC302-439 4-4 Cap, Low Side R134A Quick Connect Fitting 4-3
AC302-440 4-4 Carbon Ring Installation Tool, Kubota DI 3-4
AC302-441 4-5 Card Confifuration, Advance Microprocessor, NAO 2-15
AC302-458 4-5 Card Drive, PC (Parallel Port) 2-11
Acid Test Kit, Mineral and Synthetic Oil 6-5 Card Drive, PC (USB Port) 2-11
Acid Test Kit, Polyolester POE Oil 6-6 Card, DataBank Download 2-16
Adapter Fitting for Calibration Gas 7-6 Card, Download, 7-Unit Capacity, NAO 2-14
Adapter Injector Line (Accessory for 07-00140-00) 3-1 Card, Option, DataTrak, NAO 100-Click 2-15
Adapter, 1/4” NPT X 1/2” Acme 4-2 Card, Option, DataTrak, NAO 10-Click 2-15
Adapter, 12 VDC Vehicle 2-14 Card, Option, DataTrak, NAO 5-Click 2-14
Adapter, 120 VAC 2-14 Card, Option, IntelliSet, NAO, 10-Click 2-15
Adapter, 90 Degree Female ¼” Flare x Quick 4-5 Card, Option, IntelliSet, NAO, 5-Click 2-15

Adapter, 90 Degree Female ¼” Flare x Quick Connect 4-4 Card, Program, Advance Microprocessor, NAO 2-16
Card, Program, ML3 Controller Software and
Adapter, Compression Tester 8mm Glow Plug 3-3 Configuration 2-16
Adapter, Female, ¼” x Quick Connect (High Side) with
Cap 4-4 Case, Meter, For use with 07-00013-00 5-4
Adapter, Female, ¼” x Quick Connect (Low Side) with
Cap 4-4 Case, Universal Megohmeter 2-1
Adapter, Injector to Tester 3-2 Cavity Plug, 12-16 Gauge 2-9
Adapter, Kubota 10mm Glow Plug 3-2 Chart Holder – Orange Plastic 3-2
Adapter, Kubota CT4-114 Engine 3-3 Charts, 10-40 Bar 3-2
Adapter, Mercedes 0M636 3-2 Charts, 150-850PSI 3-2
Adapter, R134A (LO) 4-2 Coil Cleaner – Evap Foam No Rinse 7-7
Air Gap Gauge Tool (ULTRA Clutch) 5-5 Coil Cleaner – Nu-Brite 7-8
Air Gap Gauge Tool, Clutch 5-5 Coil Cleaner – Nu-Brite 7-8
Alignment Rods, Vector Generator, 3 pack 3-7 Coil Cleaner, Cal-Brite 7-8
Anti-Siphon Tank Insert 5-11 Coil Cleaner, Cal-Shield with Teflon 7-8
APU, Fuse, Resettable, 20 Amp 1-4 Coil Cleaner, Cal-Shield with Teflon 7-8
APU, Quick Start Compressor 1-4 Coil Cleaner, Citrus 7-7
APX Micro Service Harness 2-5 Coil Cleaner, Tri-Pow’r 7-8
 Alphabetical Index
Coil Sanitizer – Bio-Fresh CD 7-9 Driver, Bearing 5-7
Coil Sanitizer – Bio-Fresh CD 7-9 Driver, Bearing Plate 5-7
Coil Sanitizer – PanPads ACP 7-9 Element 6-7
Compound Gauge 6-2 Engine Platform Tool 3-6
Compound Gauge 6-2 Engine Platform Tool 5-10
Compression Test (Diesel Engines 150-850PSI) 3-1 Epoxy Repair Kit for Evaporator Pods 5-11
Compression Test Adapter Tier 4 engines 3-2 Extractor (EPROM) 2-6
Compressor Oil Refractometer 1-3 Extractor (EPROM), I-30S 2-6
Condenser Fan Removal Tool 5-7 Extractor Pin 2-6
Container, Air Compressor Tool Kit 1-5 Extractor Pin (AMP Connector) 2-6
Container, Terminal Box Tool, Contrainer Scroll
Compressor 1-5 Extractor, ML-2, ML-2i, and ML-3 Connector 2-6
Coolant Bottle Test Adapter 3-5 Fast Splice Kit, Cable Repair 2-10
Coolant Bottle Test Adapter 3-5 Fast Splice Kit, Cable Repair 2-10
Coolant Hose Lubricant 3-4 Filter Housing – Internal 6-10
Copper Reactor for Halide Torch 6-7 Filter, Felt Sock for Clean-Up, 05G Compressors 1-2
Core, Schrader Valve 4-1 Filter, Felt Sock for Clean-Up, 05K Compressors 1-2
Coupler, Quick-Connect, Gauge Hose High Side
R134A 6-4 Filter, Regular Core 6-9

Coupler, Quick-Connect, Gauge Hose Low Side R134A 6-3 Filter, Solid Core - Acid 6-9
Fitting, Male 1/4” NPT X Male 1/4” Flare Access Port
Coupling, R134A 4-4 with Schrader 4-1
Fitting, Male 1/8” NPT X Male 1/4” Flare Access Port
Crank Pulley Impact Socket 3-6 with Schrader 4-1
Crimper, AMP Unsealed 2-7 Flashtube, Xenon (for 07-00206-00 Strobe Light) 5-1
Crimper, Metripack ML-2, ML-2i, ML-3 Connectors 2-7 Flush – Rx Acid Scavenger 7-12
Crimper, Micro Pin 2-7 Flush – Rx11 Flush 7-11
Crimper, Unsealed 2-7 Flush - Rx11 Flush 7-11
Crimper, Weatherpack 2-7 Flush – Rx11 Flush Fitting Assembly 7-12
Crimper, Weatherpack 2-7 Flush - Rx11 Flush, 2-in1 Display 7-11
Crowfoot Wrench - 1 1/8” 5-8 Flywheel Locking Tool 5-10
Crowfoot Wrench - 1 3/8” 5-8 Flywheel Locking Tool 3-7
Crowfoot Wrench - 2 1/8” 5-8 Front Seal Install Tool 3-3
Crowfoot Wrench, New Water Temperature Sensor 3-4 Gas leak Detectors – Cal-Blue 7-11
DataCold 500R 2-17 Gas leak Detectors – Cal-Blue 7-11
DataCold 500T 2-17 Gas leak Detectors – Cal-Blue 7-11
DataReader (Container) 2-4 gas, Calibration 7-6
DataTrak 10 click (license) USB flash drive 2-16 Gasket 6-3
DataTrak 5 click (license) USB flash drive 2-16 Gasket 6-3
DD19CA061 4-1 Gasket 6-4
DIABLO-115V 6-13 Gauge, Belt Tension 5-1
DIABLO-240V 6-13 Gauge, Magnehelic 5-1
Diagnostic Tool, Cab Command Cable 2-4 Gauge, Sheave (34 Degree) 5-7
Dispensing Gun, Static Mixing 6-11 Grease, Heat Conductive Sealer 7-5
Download Cable Palm Top 2-12 Grease, Lithium Base 7-5
Download Cable, 20' 2-12 Grease, N-2 7-5
Download Cable, 20-Foot 2-12 Guide Tool, Installation 5-7
Download Cable, 6' 2-12 Hand Towels – Kleen-N-Toss 7-12
Download Cable, 6-Foot 2-11 Handwheel Package 6-1
Download Cable, PC, Container 2-12 Harness, CSMV 2-5
Download Cable, W Maersk Veam Connector 2-12 Harness, EVXV 2-5
Driver Tool, Seal 5-6 Head Assembly, Halide Leak Detector 6-7
 Alphabetical Index
Heat Gun, 120V-50/60hz - 570-1000 degrees F 5-2 Main Bearing Extract Tool 3-5
Heavy Duty Plus II Charging / Vacuum Hose 6-5 Main Bearing Install Tool 3-5
Hex Head Security Stepper Valve 6-12 Main Bearing Install Tool 3-5
High Side Pressure Gauge 6-1 Male 1/4” NPT X Female 7/16” Straight Thread 4-2

High Speed USB to Serial Adapter RS232 Interface 2-12 Male 7/16”-20 Straight Thread O-Ring x Female ¼” NPT 4-3

Hose Replacement, Hose Assembly 3-1 Male 9/16-18 Straight Thread O-Ring x Female ¼” NPT 4-3
Hose Set 6-2 Manifold Gauge Set 6-1
Hose Set (Consists of 07-00307-01, -02, -03) 6-2 Manifold Gauge Set 6-1
Hose, Blue 6-3 Manifold Gauge Set, Kit CFC 6-1
Hose, Red 6-3 Marine - Sleeve Puller (5F Compressors) 1.5
Hose, Replacement, 9-Foot 5-1 Marine - Sleeve Puller (5H Compressors) 1.5
Hose, Yellow 6-2 Meter, Coolant Refractometer 3-4
HumiSeal 7-6 Meter, Megohmeter 2-1
Injector Puller Set 3-3 Meter, Refractometer for Compressor Oil 6-9
Inserter (EPROM) 2-6 Mirror, Inspection 5-8
Install Tool, TK Shaft Seal 1-2 Multimeter, Digital 2-2
Insulation – Cork Insulation Tape 7-10 Multi-meter, Digital 5-3
Insulation – Foam Insulation Tape 7-10 Multimeter, Digital, Pen Type 2-1
Insulation – Insulation Slugs 7-10 Multimeter, Digital, Wavetek 2-2
Insulation – Nu-Foam Insulation Foam 7-10 Oil 32ST 7-3
Join Termial 14-16 Gauge 2-8 Oil Compressor (S-68) 7-2
Join Terminal 14-18 Gauge 2-9 Oil Drain Tool X2, X4 Belt Drive Units 3-7
Jumper, Config (Advance Micro) 2-11 Oil Drain Tool, Vector Units 3-6
Jumper, PC Mode (Advance Micro) 2-11 Oil Filter Kit, 05G Compressor 6-10
Kit, Hose Cutter, Crimper, Expander and Plastic Case 6-11 Oil Filter Kit, Bus 6-12
Kit, Static Dissipate 2-5 Oil Pump, 1 to 5 Gallons 6-5
Kit, Test Leads 2-3 Oil Test Kit – Phase III 7-12
Kit, Valve Pad Blank-Off, 4-bolt, 2-1/2" Centerline 1-3 Oil, Castrol, E-68 7-3
Kit, Valve Pad Blank-Off, Unloader Head HGBP 1-3 Oil, Compressor - (SW20) 7-1
Kit, Valve Pad Blank-Off, Unloader Head Suction Cut-
Off 1-3 Oil, Compressor - (SW20) 7-2
Kit, Valve Pad Blank-Off, Unloader Head Suction Cut-
off 1-3 Oil, Compressor - Mineral (150) 7-1
Kit, Valve Pad, Blank-Off, 2-Botl, 1-5/8" Centerline 1-3 Oil, Compressor - Synthetic (150) 7-1
Leads, 50-Foot 5-4 Oil, Compressor – 50 PAG, R1A, 1 Quart can 7-2
Oil, Compressor – POE 35 TK Trailer units with 404A, 1
Leak Detector 6-6 gallon 7-4
Leak Detector 6-7 Oil, Compressor (S-100) 7-1
License, DataLINE 2-16 Oil, Compressor S-68 7-2
Lifting Device, 20/30S and “X” Units 5-9 Oil, Compressor, (PEOE 68) 7-2
Lifting Device, 40S/50S and “X” Units 5-10 Oil, Compressor, 300 Mineral 7-4
Lifting Tool, Vector, Generator 3-7 Oil, Compressor, 5GS 7-3
Lifting Tool, Vector, Generator 5-10 Oil, Compressor, POE 32, TK Container Units 7-4
Light Bulbs 2-10 Oil, Fan shaft, Trailer 7-4
Locking Ear and Nut 3-7 Oil, Refrigerant (Soltex VG68) Gallon 7-3
Locking Ear and Nut 5-10 Oil, Synthetic Gear Box 75W-90 7-4
Loctite 609 7-5 Oile, Vacuum pump 7-3
Low Side Compound Gauge 6-1 O-Rings (Low Side, smaller than high side) 6-4
Magnet, Check Valve Tool – Discharge 6-12 O-Rings, (High Side, bigger than low side) 6-4
Magnet, Container EXV NaturaLINE 6-12 P303-1701 7-3
Magnet, Container EXV PrimeLINE 6-12 Paint, Blue, Compressor 7-7
 Alphabetical Index
Paint, Horizon Green 7-7 Shim, Vector Generator Service 3-8
Paint, Sea Spray Green 7-6 Shim, Vector Generator Service 5-11
Paint, Touch-Up, (05G and Kubota) 7-7 Sikaflex Caulk Sealant 7-5
Paint, Touch-Up, Horizon Green 7-7 Sleeve Tool, Seal 5-6
Paint, Touch-Up, Seahorse Blue 7-6 Sleeve Tool, Seal 5-6
Paper Rolls, Pack of 5 2-13 Sleeve, Installer, Perkins Front Crankshaft Pulley 3-3
Pin Terminal, 12 Gauge 2-9 Smoke Bomb 7-6
Pliers, Crimping 6-11 Socket Terminal 12-14 Gauge 2-9
Pliers, Crimping, 06D Terminals 1-3 Socket Terminal 14-16 Gauge 2-8
Pliers, Fitting Assembly, EZ Clip 6-11 Socket Terminal 14-18 Gauge 2-9
Pliers, Unloader Ring 1-2 Socket Terminal, Connector EC - (A-K) (l-Y) 2-10
Plug, 7/16”-20 Straight Thread, O-Ring 4-2 Socket, Injector 3-3
Plug, 9/16”-18 Straight Thread, O-Ring 4-2 Socket, Spanner for Extra XT Fan clutch 5-5
Programmable Charging/Recovery Meter 6-7 Socket, Spanner for Ultra Gearbox Fan clutch 5-5
Protective Case 2-14 Socket, Spanner Nut, Large w/Grease Fitting 1-1
Quick Connector Nipple (R134A Low Side) X M13
(with cap) 4-2 Socket, Spanner Nut, Small without Grease Fitting 1-1
Quick Connector Nipple (R134A Low Side) X M15 4-3 Socket, Water Temperature Sender 3-4
Rain Cap – Flip Top 5-11 Software, DataLINE 2-16
Rear Main Wear Sleeve Install Tool 3-3 Software, Reefer Manager and Reports 2-17
Red Insulating Varnish 2-17 Splice Kit, Power Cable Repair (With Filler) 2-11
Red Insulating Varnish 7-5 Splice Kit, Power Cable Repair (Without Filler) 2-10
Refrigerant Analyzer 6-6 Splitter Harness, Satellite Power 2-13
Refrigerant Recovery Unit – 115 VAC 6-13 Sprayer, Coil Gun 7-10
Refrigerant Recovery Unit – 230/240VAC 6-13 Sprayer, No. 220CP 7-9
Refrigerant System Quick Check Kit 6-11 Sprayer, No. 300CP 7-10
Refrigeration Wrench 6-5 Sprayer, No. 50P Poly 7-9
Refrigeration Wrench, Offset 6-5 Stepper Jumper Assembly 2-5
Removal Bracket, Vector Generator 3-6 Strap, Grounding 2-5
Removal Bracket, Vector Generator 5-10 Strobe Light 2-4
Removal Tool, Blue 2-8 Strobe Light 3-7
Removal Tool, Green 2-8 Strobe Light 5-1
Removal Tool, Yellow 2-8 Suction Filter Kit 6-9
Replacement Paper, Pack of 5 2-13 Suction Filter Shell 6-10
Retrofit Kit, Service Ports for 134A Fittings 4-5 Tachometer, Laser, RPM 2-4
Rivnut Install Kit Imperial 5-9 Tap, Thread, Left-Handed 5-9
Tee, Female, ¼” Flare Swivel x Male ¼: Flare x LS Quick
Rivnut Install Kit Metric 5-9 Connect 4-4
Rivnut Tool, Frame Rework 5-9 Tee, Snubber, 1/8” NPT x 1/8” NPTF 4-4
Rod for Servicing Self-Adjusting Idlers on FrigiKing
Truck Units 5-4 Temperature Probe – 15-Foot Sealed 6-8
Rubber Band 5-2 Temperature Probe (-40° F to 1,500° F) 5-3
Schrader Core, 3/8 inch, 134A 6-13 Temperature Probe (-40° F to 1,500° F) 5-4
Schrader Core, 3/8”,134A 4-2 Temperature Probe, Air, 15-Foot Sealed 6-9
Schrader Fitting Body, ¼” Male Flare, Braze-in 4-4 Temperature Tester - 4-Lead 2-3
Seal Driver, Large Ultra Gearbox 5-6 Temperature Tester - 4-Lead 6-8
Seal Driver, Small Ultra Gearbox 5-6 Temperature Tester - Soft Case 2-4
Seal Pilot, Large Ultra Gearbox 5-6 Temperature Tester – Soft Case 6-8
Seal Pilot, Small Ultra Gearbox 5-5 Temperature Tester - Spare Lead 2-4
Sealant, Pipe Fittings on 134A Units 7-5 Temperature Tester – Spare Lead 6-8
Sensor, Replacement 6-4 Terminal Removal Tool 2-8
Sensor, Thermometer – 10-Foot 5-4 Terminal Removal Tool Kit 2-8
Sensor, Thermometer – 18-Foot 5-4 Terminal Tool 2-6
 Alphabetical Index
Test Leads (Right Angle) 2-2
Tester Inject Nozzle Replacement Bowl 3-1
Tester, Belt Tension 5-1
Tester, Inject Nozzle 3-1
Tester, Micro 2-4
Tester, ML2/ML3 2-4
Tester, Stepper Motor Drive 2-5
Thermometer, Digital, Pocket (Degrees Centigrade) 5-2
Thermometer, Digital, Pocket (Degrees Fahrenheit) 5-2
Thermometer, Infrared, Non-Contact 5-3
Thermometer, Non-Contact 5-3
Thermometer, Pocket 5-2
Threaded Rod, Vector Generator Removal 5-10
Tool, Pinch Off (CU Tube) 6-11
Total Test Acid Test Kits (6) Kits 6-6
Trailer Unit Standby Clutch Adj. Tool 1-1
Trailer Unit Standby Clutch Bearing Press Tool 1-1
Tru-Tech / Tru-View Program – Advance 2-16
Universal Hand Crimp Tool 2-8
Vacuum Gauge, Digital (Microns) 6-4
Vacuum Gauge, Electronic (Microns) 6-4
Vacuum Pump, Dual Voltage 6-5
Valve, Piercing 6-11
Vise Grip Holder 1-3
Wire Crimper, MAC Tools 2-7
Wrench (Special) Compressor Oil Pan 1-2
Wrench , Sight Glass 1-4
Wrench, Davco Filter 3-4
Wrench, Panner for Clutch Armature 1-1
Wrench, Sight Glass 1-4
Wrench, Spanner Unloader System 6-12
Wrench, Spanner, Fan, Clutch 5-7
Wrench, Spanner, Solenoid Evap 5-7
 Numerical Index

02-00010-00 7-5 07-00259-20 6-7 07-00322-00 7-6 07-00400-00 2-6

02-00067-01 7-5 07-00260-00 6-5 07-00322-02 7-6 07-00401-00 2-7
02-00130-01 7-5 07-00261-00 5-2 07-00324-00 5-3 07-00408-00 2-5
02-50010-00 3-4 07-00262-02 2-1 07-00325-00 7-3 07-00409-00 5-8
06DA-403-844 4-1 07-00263-00 1-3 07-00328-00 7-3 07-00410-00 5-8
07-00013-02 5-4 07-00264-00 1-3 07-00329-00 2-6 07-00411-00 5-8
07-00015-00 5-4 07-00265-01 6-6 07-00330-00 2-7 07-00414-00 6-4
07-00036-00 3-1 07-00266-00 6-6 07-00331-00 6-4 07-00414-01 6-4
07-00140-00 3-1 07-00267-01 1-2 07-00337-00 6-6 07-00418-00 5-8
07-00176-11 6-5 07-00268-00 2-7 07-00338-00 1-2 07-00420-00 7-7
07-00177-00 5-1 07-00270-00 7-1 07-00339-00 5-6 07-00421-00 2-16
07-00177-01 5-1 07-00274-00 7-1 07-00340-00 5-6 07-00423-00 3-4
07-00177-05 5-1 07-00275-00 7-1 07-00341-00 5-6 07-00424-00 5-4
07-00179-01 3-1 07-00276-00 5-4 07-00342-00 5-6 07-00425-00 5-3
07-00179-03 3-2 07-00277-00 2-5 07-00343-00 5-7 07-00426-00 2-16
07-00179-04 3-2 07-00290-01 2-4 07-00344-00 5-7 07-00427-00 7-3
07-00179-05 3-2 07-00292-00 7-1 07-00345-00 7-5 07-00428-00SV 2-4
07-00179-06 3-3 07-00292-01 7-2 07-00346-00 1-4 07-00429-00 6-12
07-00179-07 3-2 07-00294-00 6-1 07-00349-00 7-4 07-00430-00 7-3
07-00179-08 3-1 07-00294-00 6-1 07-00354-00 7-4 07-00432-00 5-5
07-00179-09 3-2 07-00294-01 6-1 07-00357-00 5-7 07-00434-00 6-12
07-00179-10 3-3 07-00294-05 6-1 07-00359-00 7-4 07-00435-00 3-4
07-00203-00 5-1 07-00295-00 6-6 07-00360-01 5-5 07-00436-00 1.5
07-00206-01 5-1 07-00296-00 6-7 07-00364-00 5-7 07-00438-00 2-11
07-00223-00 1-2 07-00297-00 2-6 07-00370-00 2-7 07-00439-00 2-11
07-00224-00 3-3 07-00298-00 2-6 07-00373-00 7-4 07-00440-00 2-4
07-00227-00 3-3 07-00301-00 4-2 07-00375-00SV 2-5 07-00447-00 5-9
07-00228-00 2-2 07-00302-00 5-4 07-00375-10 2-5 07-00449-00 5-9
07-00229-00 2-3 07-00303-02 5-5 07-00375-11 2-5 07-00450-00 1-4
07-00230-00 2-3 07-00303-03 5-5 07-00377-00 7-4 07-00451-00 5-9
07-00237-04 6-1 07-00304-00 2-5 07-00379-00 6-9 07-00453-00 5-9
07-00237-05 6-2 07-00307-00 6-2 07-00380-00 6-10 07-00455-00 1-1
07-00237-06 6-2 07-00307-01 6-2 07-00381-00 1-2 07-00456-00 1-1
07-00237-10 6-5 07-00307-02 6-3 07-00385-00 6-11 07-00459-00 6-12
07-00237-12 6-3 07-00307-03 6-3 07-00386-00 6-11 07-00460-00 1-2
07-00237-13 6-3 07-00307-04 6-3 07-00387-00 2-6 07-00462-01 6-8
07-00238-00 6-5 07-00307-05 6-4 07-00391-00 6-11 07-00462-03 6-9
07-00238-01 6-5 07-00308-00 5-5 07-00394-00 1.5 07-00463-00 5-1
07-00239-00 3-3 07-00309-00 5-6 07-00395-00 1.5 07-00467-00 6-11
07-00240-01 1-1 07-00310-00 5-6 07-00396-01 5-7 07-00468-00 3-5
07-00241-00 1-1 07-00311-00 5-6 07-00397-00 2-8 07-00469-00 3-5
07-00242-01 1-1 07-00313-00 7-7 07-00397-01 2-8 07-00471-00 1-2
07-00242-02 1-1 07-00314-00 6-1 07-00397-02 2-8 07-00472-00 3-5
07-00243-01 2-2 07-00315-00 6-7 07-00397-03 2-8 07-00473-00 3-5
07-00243-10 2-2 07-00316-00 1-3 07-00397-04 2-8 07-00474-00 3-5
07-00243-10 5-3 07-00316-00 6-9 07-00397-05 2-8 07-00475-00 3-5
07-00245-00 7-5 07-00317-00 7-2 07-00397-06 2-8 07-00476-00 5-7
07-00250-00 3-4 07-00317-00PK6 7-2 07-00397-07 2-8 07-00477-00 5-8
07-00253-00 5-1 07-00317-00PK6 7-2 07-00397-10 2-9 07-00478-00 5-3
07-00253-01 5-2 07-00318-00 7-2 07-00397-11 2-9 07-00479-00 7-5
07-00254-00 2-6 07-00319-00 4-2 07-00397-12 2-9 07-00479-00 2-17
07-00259-00 6-7 07-00320-00 7-2 07-00399-00 5-7 07-00480-00 7-6
 Numerical Index

07-00484-00 3-2 12-00505-53 2-14 22-50180-01 2-11 NU4133-08 7-8

07-00485-00 5-2 12-00505-55 2-15 22-50396-00 2-10 NU4148-08 7-8
07-00486-00 2-4 12-00505-70 2-15 22-50396-00PK5 2-10 NU4148-32 7-8
07-00486-00 3-7 12-00505-71 2-15 22-50397-00 2-10 NU4171-75 7-7
07-00486-00 5-1 12-00506-50 2-15 22-50398-00 2-11 NU4182-08 7-11
07-00487-00 5-2 12-00543-01 2-13 22-50420-00 2-13 NU4182-24 7-11
07-00488-01 2-4 12-00543-02 2-14 30-00210-00 5-11 NU4182-53 7-11
07-00488-01 3-7 12-00543-03 2-14 40-00086-04 4-1 NU4216-92 7-10
07-00494-00 1-4 12-00543-04 2-14 40-00086-06 4-1 NU4217-W3 7-10
07-00494-10 1-4 12-00569-51 5-4 40-00519-00 4-2 NU4218-W3 7-10
07-00496-00 2-7 12-00569-52 5-4 40-00519-01 4-2 NU4230-72 7-12
07-00498-00 2-3 12-00594 2-16 40-00520-00 4-2 NU4291-01 7-8
07-00499-00 2-3 12-00615 2-16 40-00520-01 4-3 NU4291-05 7-8
07-00502-00 2-1 12-00616 2-17 40-00520-02 4-3 NU4291-08 7-8
07-00502-10 2-1 12-00734-00 2-16 40-00520-03 4-3 NU4293-04 7-10
07-00503-00 2-12 12-00734-01 2-16 40-00523-00 4-3 NU4293-75 7-10
07-00504-00 2-3 12-00734-02 2-16 40-00523-01 4-3 NU4295-34 7-9
07-00504-00 6-8 12-50150-01 2-13 40-00524-00 4-3 NU4300-10 7-11
07-00504-01 2-4 12-50377-01/2.5 2-4 40-00524-01 4-3 NU4300-11 7-11
07-00504-01 6-8 14-00331-10 6-12 40-00528-00 4-3 NU4300-15 7-11
07-00504-02 6-8 14-00351-00 4-1 40-00528-02 4-3 NU4300-99 7-12
07-00515-00 2-5 14-00396-20 6-12 40-00529-00 4-4 NU4301-02 7-12
07-00516-00 6-5 14-00396-52 6-12 40-00545-00 4-4 NU4320-W8 7-12
07-00517-00 3-3 14-50054-00 6-9 40-01124-00 4-4 NU4371-88 7-8
07-00518-00 6-6 14-50055-00 6-9 40-01166-00 4-4 NU4770-00 7-9
07-00519-00 2-7 14-50056-00 6-10 40-01166-01 4-4 NU4771-30 7-9
07-00520-00 3-4 14-50056-01 6-10 40-01184-00 4-2 NU4772-00 7-10
07-00521-00 3-3 16-00037-00 7-6 40-60087-01 4-2 NU4774-00 7-10
07-50001-00 7-6 16-03004-00 2-10 40-60087-01 6-13 TCT1028 2-7
07-50005-00 3-2 17-13004-00 1-3 42-50017-00 6-4 PH23GH012 7-7
07-50006-00 6-11 17-13006-00 1-3 42-50018-00 6-4 PH23GH017 7-7
07-50017-00 6-7 17-13008-00 1-3 46-50002-00 7-5 PH23GL012 7-6
07-60048-00 2-6 17-13010-00 4-1 54-00630-25 3-8 SIM-583 3-6
07-60049-00 5-9 17-21056-00 1-3 54-00630-25 5-11 SKM-5670 3-6
07-60083-00 3-7 17-44037-00 4-2 58-00869-00 1-2 SKM-5670 5-10
07-60083-00 5-10 17-44706-00 4-2 58-04030-00 6-2
07-60085-02 3-7 17-55013-00 1-3 58-04165-00 1-2
07-60085-02 5-10 18-00099-40 1.5 58-50109-00 2-14
07-60085-50 3-7 20-204-244 1-4 58-60232-00 4-1
07-60085-50 5-10 22-01613-14 2-9 65-50001-00 5-11
07-60090-00 2-6 22-01613-15 2-9 68-15763-00 3-6
07-60091-00 5-10 22-01690-00 2-11 68-15763-01 3-7
07-60111-00 5-2 22-01737-00 2-11 76-00397-01 7-7
07-60117-00 6-11 22-01737-01 2-12 76-50063-00 5-11
07-60117-10 6-11 22-01737-02 2-12 76-61011-00 2-13
07-60121-00 5-10 22-01737-04 2-12 79-00965-00 4-4
07-60121-00 3-7 22-01737-06 2-12 79-60598-00 2-17
07-60132-00 6-4 22-01743-00 2-4 79-60598-20 2-17
0TB0889 4-1 22-01777-03 2-10 86-04751-00 3-6
12-00503-50 2-14 22-04253-00 2-12 86-04751-00 5-10
12-00504-50 2-16 22-04253-01 2-12 NU4126-34 7-9
12-00505-52 2-15 22-50180-00 2-11 NU4126-38 7-9
 North America Central America
Carrier Transicold and Mexico
700 Olympic Drive Ejercito Nacional 253−A Piso 5
Athens, GA 30601 USA Colonia Anahuac
Tel: 1−706−357−7223 11320 Mexico, D.F.
Fax: 1−706−355−5435 Tel: 55315010
Fax: 55315010 ext. 1005

Carrier Transicold Division,

A member of the United Technologies Corporation family. Stock symbol UTX Carrier Corporation
©201 UTC Climate | Controls | Security Printed in U. S. A. P.O. Box 4805
Syracuse, N.Y. 13221 U.S A

www.carrier.transicold.com