www.blackanddecker.
com
UK
Ireland
Australia
New Zealand
1
Downloaded from www.Manualslib.com manuals search engine
5
6 2
3
4
2 1
A B
3
7
C D
E
2
Downloaded from www.Manualslib.com manuals search engine
Intended use Do not force small tools or attachments to do the job of a
Your Black & Decker screwdriver has been designed for heavy-duty tool. The tool will do the job better and safer at the
inserting and removing screws and nuts using the appropriate rate for which it was intended. Do not force the tool.
accessories. This tool is intended for consumer use only. Warning! The use of any accessory or attachment or
Your Black & Decker charger has been designed for charging performance of any operation with this tool other than those
the battery in the tool with which it was supplied. recommended in this instruction manual may present a risk of
personal injury.
Safety instructions Check for damaged parts
◆ Warning! When using battery-powered tools, basic safety Before use, carefully check the tool for damage. Check for
precautions, including the following, should always be misalignment and seizure of moving parts, breakage of parts,
followed to reduce the risk of fire, leaking batteries, damage to guards and switches and any other conditions that
personal injury and material damage. may affect its operation. Ensure that the tool will operate
◆ Read all of this manual carefully before operating the tool. properly and perform its intended function. Do not use the tool
◆ Retain this manual for future reference. if any part is damaged or defective. Do not use the tool if the
switch does not turn it on and off. Have any damaged or
Keep work area clean defective parts repaired or replaced by an authorised repair
Cluttered areas and benches can cause accidents. agent. Never attempt any repairs yourself.
Consider work area environment Remove the battery
Do not expose the tool to rain. Do not use the tool in damp or Where the design permits, remove the battery when the tool
wet conditions. Keep the work area well lit. Do not use the is not in use, before changing any parts of the tool,
tool where there is a risk of causing fire or explosion, e.g. in accessories or attachments and before servicing.
the presence of flammable liquids and gases. Avoid unintentional starting
Keep children away Do not carry the tool with a finger on the on/off switch.
Do not allow children, visitors or animals to come near the Be sure that the tool is switched off when inserting the
work area or to touch the tool. battery into the tool.
Dress properly Do not abuse cord
Do not wear loose clothing or jewellery, as these can be Never carry the charger by its cord or pull it to disconnect from
caught in moving parts. Preferably wear rubber gloves and the socket. Keep the cord away from heat, oil and sharp edges.
non-slip footwear when working outdoors. Wear protective Store idle tools
hair covering to keep long hair out of the way. When not in use, tools, batteries and chargers should be stored
Personal protection in a dry, locked up or high place, out of reach of children.
Always use safety glasses. Use a face or dust mask whenever Maintain tools with care
the operations may produce dust or flying particles. Keep cutting tools sharp and clean for better and safer
Hearing protection should be worn. performance. Follow the instructions for maintenance and
Do not overreach changing accessories. Keep handles and switches dry, clean
Keep proper footing and balance at all times. and free from oil and grease.
Stay alert Repairs
Watch what you are doing. Use common sense. Do not This tool complies with relevant safety requirements.
operate the tool when you are tired. Repairs should only be carried out by qualified persons using
Secure workpiece original spare parts; otherwise this may result in considerable
Use clamps or a vice to hold the workpiece. It is safer and it danger to the user.
frees both hands to operate the tool.
Connect dust extraction equipment Additional safety instructions for batteries and chargers
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and Batteries
properly used. ◆ Never attempt to open for any reason.
Remove adjusting keys and wrenches ◆ Do not expose the battery to water.
Always check that adjusting keys and wrenches are removed ◆ Do not store in locations where the temperature may
from the tool before operating the tool. exceed 40 °C.
Use appropriate tool ◆ Charge only at ambient temperatures between 4 °C and
The intended use is described in this instruction manual. 40 °C.
3
Downloaded from www.Manualslib.com manuals search engine
◆ Charge only using the charger provided with the tool. Fitting and removing a screwdriver bit (fig. B)
◆ When disposing of batteries, follow the instructions given ◆ To fit a screwdriver bit (6), push it into the bit holder (2)
in the section “Protecting the environment”. until it locates.
◆ Under extreme conditions, battery leakage may occur. ◆ To remove a screwdriver bit, pull it straight from the bit
When you notice liquid on the battery, proceed as follows: holder.
- Carefully wipe the liquid off using a cloth. Avoid skin
contact. Use
- In case of skin or eye contact, follow the instructions
below. Charging the battery (fig. C)
The battery needs to be charged before first use and whenever
Warning! The battery fluid, a 25-30% solution of potassium it fails to produce sufficient power on jobs that were easily
hydroxide, can be harmful. In case of skin contact, done before. A new battery or a battery that has not been
immediately rinse with water. Neutralise with a mild acid used for a long period of time achieves full performance only
such as lemon juice or vinegar. In case of eye contact, rinse after approximately 5 charging and discharging cycles.
abundantly with clean water for at least 10 minutes. Consult a After normal use, a charging time of 12 hours will enable the
physician. tool to operate at an effective power level for most tasks.
However, further charging for up to 24 hours could significantly
◆ Do not incinerate the battery. increase the run time, depending on the battery and charging
◆ Do not attempt to charge damaged batteries. conditions. The battery may become warm while charging;
this is normal and does not indicate a problem.
Chargers
◆ Use your Black & Decker charger only to charge the battery Warning! Do not charge the battery at ambient temperatures
in the tool with which it was supplied. Other batteries below 4 °C or above 40 °C. Recommended charging
could burst, causing personal injury and damage. temperature: approx. 24 °C.
◆ Never attempt to charge non-rechargeable batteries.
◆ Have defective cords replaced immediately. ◆ To charge the battery, insert the charger plug (7) into the
◆ Do not expose the charger to water. connector (3).
◆ Do not open the charger. ◆ Plug in the charger. Switch on at the mains.
◆ Do not probe the charger. ◆ Leave the tool connected to the charger for at least 12 hours.
The tool can be left connected to the charger indefinitely.
The charger is intended for indoor use only. The charger may hum and become warm while charging;
this is normal and does not indicate a problem.
Electrical safety ◆ Before using the tool, unplug the charger and disconnect
the tool from the charger.
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains Warning! Do not use the tool while it is connected to the
voltage corresponds to the voltage on the rating charger.
plate. Never attempt to replace the charger unit with
a regular mains plug. Operating the tool (fig. D)
◆ To tighten a screw or nut, slide the on/off switch (1) to
Features the right and press it.
This tool includes some or all of the following features. ◆ To loosen a screw or nut, slide the on/off switch (1) to the
1. On/off switch with forward/reverse function left and press it.
2. Bit holder ◆ To switch the tool off, release the on/off switch.
3. Charger connector
4. Charger Hints for optimum use
5. Battery
◆ Always use the correct type and size of screwdriver bit.
Assembly ◆ If screws are difficult to tighten, try applying a small
Warning! Make sure that the tool is switched off. amount of washing liquid or soap as a lubricant.
◆ Use the spindle lock to loosen very tight screws or to
firmly tighten screws.
4
Downloaded from www.Manualslib.com manuals search engine
◆ Always hold the tool and screwdriver bit in a straight line You can check the location of your nearest authorised repair
with the screw. agent by contacting your local Black & Decker office at the
◆ When screwing in wood, it is recommended to drill a pilot address indicated in this manual. Alternatively, a list of
hole with a depth equal to the length of the screw. A pilot authorised Black & Decker repair agents and full details of our
hole guides the screw and prevents splintering or after-sales service and contacts are available on the Internet
distortion of the wood. For the optimum size of the pilot at: www.2helpU.com.
hole, refer to the table below.
◆ When screwing in hardwood, also drill a clearance hole Battery (fig. E)
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table If you want to dispose of the tool yourself, the
below. battery must be removed as described below and
Cd
disposed of in accordance with local regulations.
Screw size Pilot hole ø Pilot hole ø Clearance
(softwood) (hardwood) hole Do not short-circuit the battery terminals. Do not use
No. 6 (3.5 mm) 2 mm 2.5 mm 4 mm tools to remove the battery; only use your fingers.
No. 8 (4 mm) 3.2 mm 3.5 mm 5.0 mm
No. 10 (6 mm) 3.5 mm 4.0 mm 5.7 mm ◆ If possible, operate the tool to run the battery down
completely.
Accessories ◆ Use a screwdriver to remove the clip (8).
The performance of your tool depends on the accessory used. ◆ Pull the front part off the tool.
Black & Decker and Piranha accessories are engineered to ◆ Loosen and remove the screws on the handle clamshells.
high quality standards and designed to enhance the performance ◆ Lift the batteries out of the tool.
of your tool. By using these accessories you will get the very ◆ Disconnect the wires from the battery terminals.
best from your tool. ◆ Place the battery in a suitable packaging to ensure that
the terminals cannot be short-circuited. Take the battery
This tool uses screwdriver bits and drill bits with a 1/4" (6.35 mm) to your service agent or a local recycling station. Collected
hexagonal shank. Piranha Super-lok accessories are designed batteries will be recycled or disposed of properly.
for use with this tool.
Technical data
Maintenance KC9024 KC36
Your tool has been designed to operate over a long period of Voltage VDC 2.4 3.6
time with a minimum of maintenance. Continuous satisfactory No-load speed min-1 150 180
operation depends upon proper tool care and regular cleaning. Max. torque Nm 2.4 3.4
◆ Regularly clean the ventilation slots in your tool using a Bit holder 6.35 mm hex 6.35 mm hex
soft brush or dry cloth. Weight kg 0.30 0.34
◆ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner. Charger
Input voltage VAC 230
Protecting the environment Approx. charging time h 12
Tools EC declaration of conformity
Black & Decker declares that these products conform to:
Black & Decker provides a facility for recycling 98/37/EC, 89/336/EEC, 73/23/EEC, EN 50260, EN 55014,
Black & Decker products once they have reached the EN 60335, EN 61000
end of their working life. This service is provided LpA (sound pressure): 70 dB(A), LWA (acoustic power) 85 dB(A),
free of charge. To take advantage of this service hand/arm weighted vibration < 2.5 m/s2
please return your product to any authorised repair
agent who will collect them on our behalf. Colin Wills, Director of Engineering
BDCI, 4/F, 2 Dai Wang Street
Tai Po Industrial Estate
Tai Po NT, Hong Kong
5
Downloaded from www.Manualslib.com manuals search engine
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair wear and tear
or replace such products to ensure minimum inconvenience to
the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road Tel. 03 9895 9200
Box Hill, Victoria 3128 Fax 03 9899 7465
New Zealand
Black & Decker Tel. 09 579 7600
81 Hugo Johnson Drive Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker Tel. 01753 511234
210 Bath Road Fax 01753 551155
Slough, Berkshire SL1 3YD Helpline 01753 574277
6
Downloaded from www.Manualslib.com manuals search engine
Dealer address Date of purchase
Downloaded from www.Manualslib.com manuals search engine
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
✁
Name: ................................................................................................................................... Was this tool bought as a replacement?
Address: ................................................................................................................................ Yes
No
Town: ....................................................................................................................................
Postal code: .......................................................................................................................... Dealer address: ....................................................................................................................
..............................................................................................................................................
Was this tool a gift? ..............................................................................................................................................
Yes Data protection act:
No Tick the box if you prefer not to receive further information.
Was this tool your first purchase?
Yes
No
7
GUARANTEE CARD
○ ○ ○ ○ ○
✁
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Please complete this section immediately after the purchase of your tool and send it to Black & Decker in your country.
If you live in Australia or New Zealand, please register by using the alternative guarantee card supplied.
Downloaded from www.Manualslib.com manuals search engine
5102071-01
8
