HBXX-3817TB1-VTM | HBXX-3817TB1-A2M
4-port multibeam antenna, 4x 1710–2180 MHz, 2x 38° HPBW, RET
compatible
Enhances network capacity through six sectors site application with only three antenna faces
Single panel design supporting two separate beams perfectly optimized at horizontal pointing
angles of +27 degrees and –27 degrees from boresight
Maximizes frequency spectrum utilization to increase Average Revenue Per User (ARPU)
Reduces antenna count to minimize Cap-Ex and Op-Ex costs
High gain with excellent sector edge roll-off and azimuth sidelobe suppression
Each antenna downtilt can be independently adjusted for greater flexibility in network
optimization
General Specifications
Antenna Type Multibeam
Band Single band
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and
mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel
measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Low loss circuit board
Reflector Material Aluminum
RF Connector Interface 7-16 DIN Female
RF Connector Location Bottom
RF Connector Quantity, high band 4
RF Connector Quantity, total 4
Remote Electrical Tilt (RET) Information
Model with Factory Installed AISG 2.0 Actuator HBXX-3817TB1-A2M
Dimensions
Width 301 mm | 11.85 in
Depth 181 mm | 7.126 in
Length 1390 mm | 54.724 in
Net Weight, without mounting kit 13.6 kg | 29.983 lb
Page 1 of 3
©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 11, 2021
HBXX-3817TB1-VTM | HBXX-3817TB1-A2M
Electrical Specifications
Impedance 50 ohm
Operating Frequency Band 1710 – 2180 MHz
Polarization ±45°
Electrical Specifications
Frequency Band, MHz 1710–1880 1850–1990 1920–2180
Gain, dBi 19.3 19.6 19.9
Beam Centers, Horizontal, degrees ±27 ±27 ±27
Beamwidth, Horizontal, degrees 38 35.8 34
Beamwidth, Vertical, degrees 7.6 7.1 6.7
Beam Tilt, degrees 0–10 0–10 0–10
Horizontal Sidelobe, dB 24 24 22
USLS (First Lobe), dB 23 23 23
Gain Roll-off at Boresight, dB 10 9 9
Gain Roll-off at Boresight Tolerance, dB ±0.7 ±0.8 ±0.9
Front-to-Back Ratio at 180°, dB 33 34 35
Isolation, Cross Polarization, port to port, dB 30 30 30
VSWR | Return loss, dB 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150
Input Power per Port, maximum, watts 250 250 250
Electrical Specifications, BASTA
Frequency Band, MHz 1710–1880 1850–1990 1920–2180
Gain by all Beam Tilts, average, dBi 18.9 19.4 19.6
Gain by all Beam Tilts Tolerance, dB ±0.5 ±0.3 ±0.6
Gain by Beam Tilt, average, dBi 0 ° | 18.7 0 ° | 19.1 0 ° | 19.5
5 ° | 19.0 5 ° | 19.5 5 ° | 19.7
10 ° | 18.9 10 ° | 19.4 10 ° | 19.2
Beamwidth, Horizontal Tolerance, degrees ±1.5 ±1.2 ±2.1
Beamwidth, Vertical Tolerance, degrees ±0.4 ±0.3 ±0.5
USLS, beampeak to 20° above beampeak, dB 17 18 18
Front-to-Back Total Power at 180° ± 30°, dB 29 30 28
CPR at Boresight, dB 24 24 18
CPR at Sector, dB 12 15 13
Page 2 of 3
©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 11, 2021
HBXX-3817TB1-VTM | HBXX-3817TB1-A2M
Mechanical Specifications
Wind Loading at Velocity, frontal 202.0 N @ 150 km/h | 45.4 lbf @ 150 km/h
Wind Loading at Velocity, lateral 166.0 N @ 150 km/h | 37.3 lbf @ 150 km/h
Wind Loading at Velocity, maximum 388.0 N @ 150 km/h | 87.2 lbf @ 150 km/h
Wind Loading at Velocity, rear 205.0 N @ 150 km/h | 46.1 lbf @ 150 km/h
Wind Speed, maximum 241 km/h | 149.75 mph
Packaging and Weights
Width, packed 404 mm | 15.906 in
Depth, packed 310 mm | 12.205 in
Length, packed 1598 mm | 62.913 in
Weight, gross 25 kg | 55.115 lb
Regulatory Compliance/Certifications
Agency Classification
CE Compliant with the relevant CE product directives
CHINA-ROHS Below maximum concentration value
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance
ROHS Compliant
Included Products
BSAMNT-3 – Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members.
Kit contains one scissor top bracket set and one bottom bracket set.
* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance
Page 3 of 3
©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 11, 2021
