SF2 CDU decoder v0.
4a by vlo
CDU file: sf_cdu.bin
2048 bytes CDU detected
Led Settings
Activity LED Polarity : 1 (Inverted)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 1 (B02)
PS1 Support : 2 (No)
HIPM Support : 2 (ACK/On)
DIPM Support : 2
(Supported)
Auto-Partial to Slumber Timer for Active PS0 State : 0 (Default
(10 ms))
Auto-Partial to Slumber Timer PS States other than PS0 : 0 (Default
(0 ms))
HIPM Auto-Partial Slumber Behavior : 0 (Default)
w76b9 Supports Partial and Slumber IPM States (HIPM) : 0 (Default)
w76b13 Supports Host Automatic Partial to Slumber Transitions (HIPM) : 1 (Not
Supported)
w76b14 Supports Device Automatic Partial to Slumber Transitions (DIPM): 1 (Not
Supported)
w78b3 Supports Device Initiating Interface Power Management Request : 0 (Default)
Auto Quick Idle Timer : 0 (Default
(50ms))
DIPM Slumber COMWAKE : 2 (Enabled)
w79b7 Supports Device APS Software Settings Preservation (SSP) : 0 (Default)
w78b10 Supports DIPM Software Settings Preservation (SSP) : 1 (Not
Supported)
Auto PS1 : 8
DevSleep Settings
DevSleep Support : 2 (Supported)
DevSleep Wakeup with COMWAKE : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 1 (LM75 or TMP102)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 70
Max Temperature Threshold Level 2 Entry Point (MT2) : 75
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 8 (Temperature Threshold
Event Log, PLL/2)
Max Temperature Threshold Behavior for MT2 (MT2B) : 11 (Temperature Threshold
Event Log, PLL/4 and Heavy Write Speed SATA Throttling)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 68
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 2 (Expanded)
Enhanced Security Erase Behavior (Military Erase) : 11 Crypto erase only)
SATA Command and Firmware Options
Flush Cache Behavior : 1 (Enable Checkpoint)
ATA Security Set Enable : 1 (Off)
Spread Spectrum Clocking Enable : 1 (Off)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 2 (Enabled)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 2 (Disabled)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 2 (Low)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 1 (Disable)
Trim Support/Setting Word 169 Bit 0 : 1 (Disable)
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master
Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Max LBA Count for 512B Sectors : 234441648
Max LBA Count for 512B Plus DIFF Sectors : 0
Max LBA Count for 520B Sectors : 0
Max LBA Count for 524B : 0
Max LBA Count for 528B : 0
Max LBA Count for 4096 Sectors : 0
Max LBA Count for 4096 Plus DIFF Sectors : 0
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On
COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write
Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write
Throttling))
CDU Smart settings: defined 22 attributes
## Attr IntId Tresh Flag
00 0x05 0x28 0 0x32
01 0x09 0x04 0 0x32
02 0x0c 0x05 0 0x32
03 0xaa 0x2d 10 0x33
04 0xab 0x2e 0 0x32
05 0xac 0x2f 0 0x32
06 0xae 0x0b 0 0x32
07 0xb7 0x38 0 0x32
08 0xb8 0x0e 90 0x33
09 0xbb 0x0f 0 0x32
10 0xbe 0x12 0 0x32
11 0xc0 0x0b 0 0x32
12 0xc7 0x37 0 0x32
13 0xe1 0x2a 0 0x32
14 0xe2 0x30 0 0x32
15 0xe3 0x31 0 0x32
16 0xe4 0x32 0 0x32
17 0xe8 0x2d 10 0x33
18 0xe9 0x54 0 0x32
19 0xf1 0x2a 0 0x32
20 0xf2 0x2b 0 0x32
21 0xf9 0x1b 0 0x32
