Go to

Table of
Contents

Instrument Pipe &

ISO Conversion Fittings
Catalog 4260 May 2014
 Go to
Introduction Catalog 4260
Table of
Contents

Instrument Pipe Fittings ISO Conversion Fittings

Introduction Introduction
Parker Instrumentation Pipe Fittings are designed Parker ISO Conversion Fittings are designed to the
as leak-free connections for process, power, highest quality standards to allow connections between
instrumentation and general industrial applications. components and systems which use both NPT and
They are manufactured to the highest quality ISO Thread configurations. Conversion fittings are
standards and are available in broad ranges of sizes, maintained under strict quality ­control programs.
materials and configurations.
Design
Parker Instrumentation Pipe fittings are made at Parker ISO Conversion Fittings are designed to the
the Instrumentation Products Division of Parker most commonly used ISO thread forms. These thread
Hannifin in Huntsville, Alabama. These fittings are forms are used where pressure tight joints are either
manufactured where strict adherence to quality made on threads utilizing a thread sealant or where
control programs is maintained. pressure tight joints utilize a periph­eral seal on the face
The Parker Quality Program is a measure of the of the mating component.
efficiency with which Parker transforms materials,
our employee efforts, machinery and information into Material
customer-satisfying products and services. Parker ISO Conversion Fittings are standard in
stainless steel and brass. Other materials may be
Material special ordered within the Parker Quick Response
Parker Pipe Fittings are standard in steel and brass. Department. Straight fittings are manufactured from
Other materials may be special ordered within the applicable ASTM bar stock specifications shaped
Parker Quick Response Department. Straight fittings fittings are manufactured from close grain forgings.
are manufactured from applicable ASTM bar stock
specifications shaped fittings are manufactured from
close grain forgings.

WARNING – USER RESPONSIBILITY

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND
PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users
having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance,
maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the
information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible
for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.

Offer of Sale
The items described in this document are hereby offered for sale by Parker-Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by
the provisions stated in the detailed “Offer of Sale” elsewhere in this document or available at www.parker.com/ipdus.

© Copyright 2014, Parker Hannifin Corporation. All Rights Reserved

Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Instrument Pipe Fittings Table of
Contents

Visual Index
Female Elbow 45° Female Cross Male SAE Straight
Pipe Fittings FVE................................... page 7 FX .................................. page 10 Thread to Female NPT
Thread
Male Hex Nipple GOA .............................. page 13
MHN................................. page 4

Street Elbow
SE..................................... page 8
Pipe Cap Male Connector to SAE
Male Close Nipple CP ................................. page 11 Straight Thread
MCN................................. page 4
....................................... page 13

Street Elbow 45°

SVE.................................. page 8
FHG5

Male Hex Long Nipple Hex Head Plug

MHLN............................... page 5 PH ................................. page 11
ISO Conversion Fittings
Visual Index
................................................ 14
Female Hex Coupling Male Tee
FHC.................................. page 5
Hollow Hex Plug
MT ................................... page 9 PHH................................ page 11
Thread and Tube End
Size Charts
................................ pages 27-29

Adapter
RA..................................... page 6 Straight Thread
Pipe Data and
Female Tee Adapters Dimensions
FT .................................... page 9 ....................................... page 30
Hex Head Plug
P5ON.............................. page 12
Reducing Bushing
RB ................................... page 6 Engineering Report:
Heat Code Traceability
....................................... page 31
Street Tee
ST .................................. page 10 Hollow Hex Plug
HP5ON........................... page 12
Male Elbow Offer of Sale
ME.................................... page 7 ................................ pages 35-36

Male Branch Tee

MBT ............................... page 10 Straight Thread
P5ON

Reducer/Expander
F5OG5 ........................... page 12
Female Elbow
FE..................................... page 7

HP5ON

Visual Index for ISO Conversion Fittings on page 14.

FHG5

1 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Instrument Pipe Fittings Catalog 4260
Table of
Contents

Features and Technical Data Features

Parker Instrument Pipe Fittings are precision • Quality engineered for instrumentation applications
machined from forgings for elbows, tees and crosses • Packaged in sealed, clear plastic shrink wrapped
and from bar stock for straight connectors. They boxes for cleanliness
are designed to be used for process control and • Working pressures calculated in accordance with
instrumentation connections between pipe sizes and Power Piping Code ANSI B31.1 and Refiner Piping
tube sizes. Code ANSI B31.3.
• All pipe threads are National Pipe Taper (NPT) and
exceed the requirements of ANSI B1.20.1.
• Rolled male threads for extra strength
• Straight bodies machined from applicable ASTM bar
stock specifications
• Shapes machined from close grain forgings
• Size ranges from 1/16" through 2" NPT
• Materials – 316 Stainless Steel, Brass and Steel.
(Other materials by special order)
• All exposed threads protected to prevent damage

Pipe Dimensions
N.P.T. Pipe E R
Pipe Size Thread R Ref.
1/16 1/16 – 27 .38 .11
1/8 1/8 – 27 .38 .19
E REF.
1/4 1/4 – 18 .56 .28
3/8 3/8 – 18 .56 .41
1/2 1/2 – 14 .75 .50
3/4 3/4 – 14 .75 .62
N.P.T. PIPE THREAD
1 1 – 11-1/2 .94 .94
1-1/4 1-1/4 – 11-1/2 .97 1.25
1-1/2 1-1/2 – 11-1/2 1.00 1.50
2 2 – 11-1/2 1.03 1.94

NPT Threads Generic Thread

The National Pipe Taper (NPT) thread has a thread PITCH

flank angle of 60° inclusive, and is mainly used in the
petrochemical and process industries.

NPT – National Pipe Taper threads for connections

where pressure-tight joints are made on the threads MAJOR DIA.
PITCH DIA.
utilizing a thread sealant. MINOR DIA.
FLANK ANGLE

2 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Instrument Pipe Fittings Table of
Contents

How To Order
Parker Instrument Pipe Fittings part numbers are constructed from symbols that identify the size and style of the
fitting and material used.

The example shown below describes a male hex nipple for 3/8" NPT male pipe and 1/4" NPT male pipe in 316
stainless steel.

Example: 6-4 MHN-SS

6 – 4 MHN – SS

1st 2nd Fitting Body

End End Type Material

3/8" NPT 1/4" NPT Male Hex

316 SS
Male Pipe Male Pipe Nipple

Parker Instrument Pipe Fittings are ordered by part number as listed in this catalog. 4

Size: Pipe thread sizes are designated by the number of sixteenths of an inch.
(3/8 NPT pipe = 6/16 = 6) 1 2

Thread Type: All pipe threads are National Pipe Taper (NPT) unless otherwise designated.

Straights and Elbows: Call out the largest pipe end first followed by the smaller pipe size.
3
See MHN example on page 4.

Tees and Crosses: For tees that are the same pipe sizes on all ends the size designation is shown below:

 Example: 6-6-6 FT-B would be a 3/8" NPT Female Tee in brass.

  Example: 4 FX-SS would be a 1/4" NPT Female Cross in 316 SS.

If a reducing tee or cross were specified, each size must be in sequence. First size the largest run (1 to 2) and
then the branch (3 to 4).
 Example: 6-6-6-4 FX-SS

Material: Basic Material Type (B = Brass, SS = 316 Stainless Steel, S = Steel)

Special Fittings: If there is any question as to the fitting desired, particularly for special fitting configurations, it is
suggested that a customer print be submitted with the fitting request for quote.

Availability: Items priced in current Price List 4260 are carried in stock. Price and delivery for non-standard items
quoted on request through the quick response department.

3 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Instrument Pipe Fittings Catalog 4260
Table of
Contents

Male Hex Nipple NPT Thread Working Pressures

Male (PSIG)
MHN Parker W D R Stainless
Part No. T1 T2 Hex (in.) (in.) Brass Steel Steel
1-1 MHN 1/16 1/16 7/16 1.06 .38 6000 10000 10500
2-1 MHN 1/8 1/16 7/16 1.06 .38 5600 9100 9700
2-2 MHN 1/8 1/8 7/16 1.06 .38 5600 9100 9700
4-1 MHN 1/4 1/16 5/8 1.25 .56/.38 4100 7500 8000
D
R 4-2 MHN 1/4 1/8 5/8 1.25 .56/.38 4100 7500 8000
4-4 MHN 1/4 1/4 5/8 1.45 .56 4100 7500 8000
6-1 MHN 3/8 1/16 3/4 1.27 .56/.38 4000 7200 7600
T1 T2
6-2 MHN 3/8 1/8 3/4 1.27 .56/.38 4000 7200 7600
6-4 MHN 3/8 1/4 3/4 1.45 .56 4000 7200 7600
W HEX 6-6 MHN 3/8 3/8 3/4 1.45 .56 4000 7200 7600
8-2 MHN 1/2 1/8 7/8 1.52 .75/.38 3900 6600 7000
8-4 MHN 1/2 1/4 7/8 1.70 .75/.56 3900 6600 7000
8-6 MHN 1/2 3/8 7/8 1.70 .75/.56 3900 6600 7000
8-8 MHN 1/2 1/2 7/8 1.89 .75 3900 6600 7000
12-2 MHN 3/4 1/8 1-1/8 1.59 .75/.38 3800 6400 6800
12-4 MHN 3/4 1/4 1-1/8 1.78 .75/.56 3800 6400 6800
12-6 MHN 3/4 3/8 1-1/8 1.78 .75/.56 3800 6400 6800
12-8 MHN 3/4 1/2 1-1/8 1.97 .75 3800 6400 6800
12-12 MHN 3/4 3/4 1-1/8 1.97 .75 3800 6400 6800
16-2 MHN 1 1/8 1-3/8 1.78 .94/.38 2700 4600 4900
16-4 MHN 1 1/4 1-3/8 1.97 .94/.56 2700 4600 4900
16-6 MHN 1 3/8 1-3/8 1.97 .94/.56 2700 4600 4900
16-8 MHN 1 1/2 1-3/8 2.16 .94/.75 2700 4600 4900
16-12 MHN 1 3/4 1-3/8 2.09 .94/.75 2700 4600 4900
16-16 MHN 1 1 1-3/8 2.34 .94 2700 4600 4900
20-16 MHN 1-1/4 1 1-3/4 2.45 .97/.94 2000 3500 3700
20-20 MHN 1-1/4 1-1/4 1-3/4 2.48 .97 2000 3500 3700
24-24 MHN 1-1/2 1-1/2 2 2.61 1.00 1800 2900 3100

Male Close Nipple Working Pressure (PSIG)

Parker NPT Thread D R Stainless
MCN Part No. Male (in.) (in.) Brass Steel Steel
1-1 MCN 1/16 .75 .34 6000 10000 10500
2-2 MCN 1/8 .75 .34 5600 9100 9700
4-4 MCN 1/4 1.13 .49 4100 7500 8000
D 6-6 MCN 3/8 1.13 .48 4000 7200 7600
R R 8-8 MCN 1/2 1.50 .66 3900 6600 7000
12-12 MCN 3/4 1.50 .66 3800 6400 6800
T1 T2 16-16 MCN 1 1.88 .84 2700 4600 4900

Dimensions for reference only, subject to change.

4 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Instrument Pipe Fittings Table of
Contents

Male Hex NPT Thread Male Working Pressure (PSIG)

Parker W D R Stainless
Long Nipple Part No.* T1 T2 Hex (in.) (in.) Brass Steel Steel
MHLN 1-1 MHLN-#  † 1/16 1/16 7/16 * .38 6000 10000 10500
2-2 MHLN-#  † 1/8 1/8 7/16 * .38 5600 9100 9700
2-2 MHLN-#  1.5 1/8 1/8 7/16 1.50 .38 5600 9100 9700
2-2 MHLN-#  2.0 1/8 1/8 7/16 2.00 .38 5600 9100 9700
D 2-2 MHLN-#  2.5 1/8 1/8 7/16 2.50 .38 5600 9100 9700
R
4-4 MHLN-#  † 1/4 1/4 5/8 * .56 4100 7500 8000
T1 T2
4-4 MHLN-#  2.0 1/4 1/4 5/8 2.00 .56 4100 7500 8000
W HEX 4-4 MHLN-#  2.5 1/4 1/4 5/8 2.50 .56 4100 7500 8000
4-4 MHLN-#  3.0 1/4 1/4 5/8 3.00 .56 4100 7500 8000
4-4 MHLN-#  4.0 1/4 1/4 5/8 4.00 .56 4100 7500 8000
6-6 MHLN-#  † 3/8 3/8 3/4 * .56 4000 7200 7600
8-8 MHLN-#  † 1/2 1/2 7/8 * .75 3900 6600 7000
8-8 MHLN-#  2.0 1/2 1/2 7/8 2.00 .75 3900 6600 7000
8-8 MHLN-#  3.0 1/2 1/2 7/8 3.00 .75 3900 6600 7000
# Insert material designator *Part Number Example: 8-8 MHLN-SS 3.0
† Specify Length in 0.5 inch increments

Female Hex NPT Thread Working Pressures

Female (PSIG)
Coupling Parker W D Stainless
FHC Part No. T1 T2 Hex (in.) Brass Steel Steel
1-1 FHC 1/16 1/16 1/2 .75 4500 7500 8000
2-1 FHC 1/8 1/16 5/8 .75 4000 6400 6800
2-2 FHC 1/8 1/8 5/8 .75 4000 6400 6800
4-1 FHC 1/4 1/16 3/4 .92 4300 6600 7000
4-2 FHC 1/4 1/8 3/4 .94 4300 6600 7000
D
4-4 FHC 1/4 1/4 3/4 1.13 4300 6600 7000
6-1 FHC 3/8 1/16 7/8  .95 3500 5300 5600
6-2 FHC 3/8 1/8 7/8 1.03 3500 5300 5600
T1 T2 6-4 FHC 3/8 1/4 7/8 1.13 3500 5300 5600
6-6 FHC 3/8 3/8 7/8 1.13 3500 5300 5600
W HEX 8-2 FHC 1/2 1/8 1-1/8 1.22 3600 5200 5500
8-4 FHC 1/2 1/4 1-1/8 1.38 3600 5200 5500
8-6 FHC 1/2 3/8 1-1/8 1.50 3600 5200 5500
8-8 FHC 1/2 1/2 1-1/8 1.50 3600 5200 5500
12-2 FHC 3/4 1/8 1-3/8 1.39 3000 4300 4600
12-4 FHC 3/4 1/4 1-3/8 1.55 3000 4300 4600
12-6 FHC 3/4 3/8 1-3/8 1.69 3000 4300 4600
12-8 FHC 3/4 1/2 1-3/8 1.88 3000 4300 4600
12-12 FHC 3/4 3/4 1-3/8 1.53 3000 4300 4600
16-2 FHC 1 1/8 1-5/8 1.44 3100 4500 4800
16-4 FHC 1 1/4 1-5/8 1.63 3100 4500 4800
16-6 FHC 1 3/8 1-5/8 1.63 3100 4500 4800
16-8 FHC 1 1/2 1-5/8 1.77 3100 4500 4800
16-12 FHC 1 3/4 1-5/8 1.72 3100 4500 4800
16-16 FHC 1 1 1-5/8 1.89 3100 4500 4800
20-16 FHC 1-1/4 1 2 1.94 2300 3500 3700
20-20 FHC 1-1/4 1-1/4 2 1.94 2300 3500 3700
24-24 FHC 1-1/2 1-1/2 2-3/8 1.94 2100 3200 3400

Dimensions for reference only, subject to change.

5 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Instrument Pipe Fittings Catalog 4260
Table of
Contents

Adapter NPT Thread Working Pressures (PSIG)

Female Male
RA Parker
Part No. T1 T2
W
Hex
D
(in.)
R
(in.) Brass
Stainless
Steel Steel
2-1 RA 1/8 1/16 5/8 1.03 .38 4000 6400 6800
2-2 RA 1/8 1/8 5/8 1.03 .38 4000 6400 6800
4-1 RA 1/4 1/16 3/4 1.20 .38 4300 6600 7000
4-2 RA 1/4 1/8 3/4 1.20 .38 4300 6600 7000
D 4-4 RA 1/4 1/4 3/4 1.39 .56 4300 6600 7000
R 6-1 RA 3/8 1/16 7/8 1.25 .38 3500 5300 5600
6-2 RA 3/8 1/8 7/8 1.25 .38 3500 5300 5600
T1 T2 6-4 RA 3/8 1/4 7/8 1.44 .56 3500 5300 5600
6-6 RA 3/8 3/8 7/8 1.44 .56 3500 5300 5600
W HEX 8-2 RA 1/2 1/8 1-1/8 1.50 .38 3600 5200 5500
8-4 RA 1/2 1/4 1-1/8 1.69 .56 3600 5200 5500
8-6 RA 1/2 3/8 1-1/8 1.69 .56 3600 5200 5500
8-8 RA 1/2 1/2 1-1/8 1.88 .75 3600 5200 5500
12-2 RA 3/4 1/8 1-3/8 1.56 .38 3000 4300 4600
12-4 RA 3/4 1/4 1-3/8 1.75 .56 3000 4300 4600
12-6 RA 3/4 3/8 1-3/8 1.75 .56 3000 4300 4600
12-8 RA 3/4 1/2 1-3/8 1.94 .75 3000 4300 4600
16-2 RA 1 1/8 1-5/8 1.81 .38 3100 4500 4800
16-4 RA 1 1/4 1-5/8 2.00 .56 3100 4500 4800
16-6 RA 1 3/8 1-5/8 2.00 .56 3100 4500 4800
16-8 RA 1 1/2 1-5/8 2.19 .75 3100 4500 4800
16-12 RA 1 3/4 1-5/8 2.19 .75 3100 4500 4800
16-16 RA 1 1 1-5/8 2.38 .94 2700 4500 4800
20-16 RA 1-1/4 1 2 2.47 .94 2300 3500 3700

Reducing NPT Thread Working Pressures (PSIG)

Male Female
Bushing Parker
Part No. T1 T2
W
Hex
D
(in.)
R
(in.) Brass
Stainless
Steel Steel
RB 2-1 RB 1/8 1/16 7/16 .63 .38 2900 6400 6800
4-1 RB 1/4 1/16 5/8 .86 .56 4100 7500 8000
4-2 RB 1/4 1/8 5/8 .86 .56 3600 6000 6400
6-1 RB 3/8 1/16 3/4 .86 .56 4000 7200 7600
6-2 RB 3/8 1/8 3/4 .86 .56 4000 6400 6800
6-4 RB 3/8 1/4 3/4 .86 .56 3000 5300 5600
D 8-2 RB 1/2 1/8 7/8 1.11 .75 3900 6600 6800
8-4 RB 1/2 1/4 7/8 1.11 .75 3900 6400 7000
T2 T1 8-6 RB 1/2 3/8 7/8 1.11 .75 2800 4600 4900
12-2 RB 3/4 1/8 1-1/8 1.17 .75 3800 6400 6800
12-4 RB 3/4 1/4 1-1/8 1.17 .75 3800 6400 6800
W HEX R
12-6 RB 3/4 3/8 1-1/8 1.17 .75 3500 5300 5600
12-8 RB 3/4 1/2 1-1/8 1.17 .75 2800 4900 5200
16-2 RB 1 1/8 1-3/8 1.36 .94 2700 4600 4900
16-4 RB 1 1/4 1-3/8 1.36 .94 2700 4600 4900
16-6 RB 1 3/8 1-3/8 1.36 .94 2700 4600 4900
16-8 RB 1 1/2 1-3/8 1.36 .94 2700 4600 4900
16-12 RB 1 3/4 1-3/8 1.36 .94 2500 4200 4500
20-12 RB 1-1/4 3/4 1-3/4 1.47 .97 2000 3500 3700
20-16 RB 1-1/4 1 1-3/4 1.47 .97 2000 3500 3700
24-16 RB 1-1/2 1 2 1.58 1.00 1800 2900 3100
24-20 RB 1-1/2 1-1/4 2 1.58 1.00 1700 2700 2800

Dimensions for reference only, subject to change.

6 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Instrument Pipe Fittings Table of
Contents

Male Elbow NPT Working Pressures (PSIG)

Parker Thread W H R Stainless
ME Part No. Male Hex (in.) (in.) Brass Steel Steel
1-1 ME 1/16 3/8 .66 .38 5500 9500 10100
2-2 ME 1/8 7/16 .76 .38 5000 9100 9700
4-4 ME 1/4 9/16 1.09 .56 4100 7500 8000
6-6 ME 3/8 3/4 1.22 .56 4000 7200 7600
8-8 ME 1/2 7/8 1.47 .75 3100 5800 6200
12-12 ME 3/4 1-1/16 1.59 .75 3400 6400 6800
16-16 ME 1 1-5/16 1.97 .94 2700 4600 4900

H
W HEX

Female Elbow Working Pressures (PSIG)

NPT
FE Parker Thread W H H1 Stainless
Part No. Female Hex (in.) (in.) Brass Steel Steel
1-1 FE 1/16 7/16 .50 .50 3800 7000 7500
2-1 FE 1/8 - 1/16 9/16 .66 .66 2900 5500 5900
2-2 FE 1/8 9/16 .66 .66 2900 5500 5900
4-2 FE 1/4 - 1/8 3/4 .88 .88 2900 5500 5900
4-4 FE 1/4 3/4 .88 .88 3000 5600 6000
W HEX H
6-6 FE 3/8 7/8 1.02 1.02 2700 5000 5300
8-8 FE 1/2 1-1/16 1.23 1.23 2500 4500 4800
12-12 FE 3/4 1-5/16 1.36 1.36 2000 3500 3700
16-16 FE 1 1-5/8 1.63 1.63 2300 3900 4200
H1
20-20 FE 1-1/4 1-7/8 1.70 1.70 1900 3100 3300
24-24 FE 1-1/2 2-1/2 2.08 2.08 1700 2500 2600

Female Elbow 45° NPT Working Pressures (PSIG)

Parker Thread W H H1 Stainless
FVE H Part No. Female Hex (in.) (in.) Brass Steel Steel
1-1 FVE 1/16 7/16 .47 .47 3800 7000 7500
H1

2-2 FVE 1/8 9/16 .47 .47 2900 5500 5900

4-4 FVE 1/4 3/4 .69 .69 3000 5600 6000
6-6 FVE 3/8 7/8 .75 .75 2700 5000 5300
W HEX
8-8 FVE 1/2 1-1/16 .94 .94 2500 4500 4800
12-12 FVE 3/4 1-5/16 1.00 1.00 2000 3500 3700
16-16 FVE 1 1-5/8 1.19 1.19 2300 3900 4200

Dimensions for reference only, subject to change.

7 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Instrument Pipe Fittings Catalog 4260
Table of
Contents

Street Elbow NPT Working Pressures

Thread (PSIG)
SE Parker W H H1 R Stainless
Part No. Male Female Hex (in.) (in.) (in.) Brass Steel Steel
1-1 SE 1/16 1/16 9/16 .66 .72 .38 3800 7000 7500
2-1 SE 1/8 1/16 9/16 .66 .78 .38 3800 7000 7500
2-2 SE 1/8 1/8 9/16 .66 .78 .38 2900 5500 5900
4-1 SE 1/4 1/16 9/16 .66 1.09 .56 3800 7000 7500
4-2 SE 1/4 1/8 9/16 .66 1.09 .56 2900 5500 5900
W HEX H1 4-4 SE 1/4 1/4 3/4 .88 1.09 .56 3000 5600 6000
6-1 SE 3/8 1/16 3/4 .88 1.09 .56 3800 7000 7500
6-2 SE 3/8 1/8 3/4 .88 1.22 .58 2900 5500 5900
6-4 SE 3/8 1/4 3/4 .88 1.22 .56 3000 5600 6000
H 6-6 SE 3/8 3/8 7/8 1.02 1.22 .56 2700 5000 5300
R
8-2 SE 1/2 1/8 7/8 .95 1.47 .75 2900 5500 5900
8-4 SE 1/2 1/4 7/8 .95 1.47 .75 3000 5600 6000
8-6 SE 1/2 3/8 7/8 1.23 1.47 .75 2700 5000 5300
8-8 SE 1/2 1/2 1-1/16 1.23 1.47 .75 2500 4500 4800
12-2 SE 3/4 1/8 1-1/16 1.00 1.59 .75 2900 5500 5900
12-4 SE 3/4 1/4 1-1/16 1.00 1.59 .75 3000 5600 6000
12-6 SE 3/4 3/8 1-1/16 1.23 1.59 .75 2700 5000 5300
12-8 SE 3/4 1/2 1-1/16 1.23 1.59 .75 2500 4500 4800
12-12 SE 3/4 3/4 1-5/16 1.36 1.59 .75 2000 3500 3700
16-2 SE 1 1/8 1-5/16 1.63 1.97 .94 2700 5500 5900
16-4 SE 1 1/4 1-5/16 1.63 1.97 .94 2700 5600 6000
16-6 SE 1 3/8 1-5/16 1.50 1.97 .94 2700 5000 5300
16-8 SE 1 1/2 1-5/16 1.63 1.97 .94 2500 4500 4800
16-12 SE 1 3/4 1-5/16 1.36 1.97 .94 2000 3500 3700
16-16 SE 1 1 1-5/8 1.63 1.97 .94 2300 3900 4200
20-20 SE 1-1/4 1-1/4 1-7/8 1.70 2.38 .97 1900 3100 3300

Street Elbow 45° NPT Working Pressures

Thread (PSIG)
SVE Parker W H H1 R Stainless
Part No. Male Female Hex (in.) (in.) (in.) Brass Steel Steel
1-1 SVE 1/16 1/16 7/16 .47 .66 .38 3800 7000 7500
2-2 SVE 1/8 1/8 9/16 .47 .72 .38 2900 5500 5900
4-4 SVE 1/4 1/4 3/4 .63 1.05 .56 3000 5600 6000
6-6 SVE 3/8 3/8 7/8 .72 1.06 .56 2700 5000 5300
8-8 SVE 1/2 1/2 1-1/16 .91 1.34 .75 2500 4500 4800
WH 12-12 SVE 3/4 3/4 1-5/16 .97 1.38 .75 2000 3500 3700
EX
H 16-16 SVE 1 1 1-5/8 1.13 1.72 .94 2300 3900 4200
H1

Dimensions for reference only, subject to change.

8 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Instrument Pipe Fittings Table of
Contents

Male Tee NPT Working Pressures (PSIG)

MT Parker
Part No.
Thread
Male
W
Hex
H1
(in.)
R
(in.) Brass
Stainless
Steel Steel
1-1-1 MT 1/16 5/16 .72 .38 5500 9500 10100
2-2-2 MT 1/8 7/16 .76 .38 5000 9100 9700
4-4-4 MT 1/4 9/16 1.09 .56 4100 7500 8000
6-6-6 MT 3/8 3/4 1.22 .56 4000 7200 7600
8-8-8 MT 1/2 7/8 1.47 .75 3100 5800 6200
12-12-12 MT 3/4 1-1/16 1.59 .75 3400 6400 6800
16-16-16 MT 1 1-5/16 1.97 .94 2700 4600 4900
20-20-20 MT 1-1/4 1-5/8 2.22 .97 2000 3500 3700
H1
24-24-24 MT 1-1/2 1-7/8 2.64 1.00 1800 2900 3100
R

W HEX

Female Tee NPT Working Pressures (PSIG)

Parker Thread W H Stainless
FT Part No. Female Hex (in.) Brass Steel Steel
1-1-1 FT 1/16 7/16 .50 3800 7000 7500
2-2-2 FT 1/8 9/16 .66 2900 5500 5900
4-4-4 FT 1/4 3/4 .88 3000 5600 6000
6-6-6 FT 3/8 7/8 1.02 2700 5000 5300
8-8-8 FT 1/2 1-1/16 1.23 2500 4500 4800
12-12-12 FT 3/4 1-5/16 1.36 2000 3500 3700
H 16-16-16 FT 1 1-5/8 1.63 2300 3900 4200
20-20-20 FT 1-1/4 1-7/8 1.70 1900 3100 3300
24-24-24 FT 1-1/2 2-1/2 2.08 1700 2500 3600

W HEX

Dimensions for reference only, subject to change.

9 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Instrument Pipe Fittings Catalog 4260
Table of
Contents

Street Tee NPT Working Pressures

Thread (PSIG)
ST Parker W H H1 R Stainless
Part No. Male Female Hex (in.) (in.) (in.) Brass Steel Steel
1-1-1 ST 1/16 1/16 7/16 .50 .72 .38 3800 7000 7500
2-2-2 ST 1/8 1/8 9/16 .66 .78 .38 2900 5500 5900
4-4-4 ST 1/4 1/4 3/4 .88 1.09 .56 3000 5600 6000
6-6-6 ST 3/8 3/8 7/8 1.02 1.22 .56 2700 5000 5300
8-8-8 ST 1/2 1/2 1-1/16 1.23 1.47 .75 2500 4500 4800
H H1 12-12-12 ST 3/4 3/4 1-5/16 1.36 1.59 .75 2000 3500 3700
R 16-16-16 ST 1 1 1-5/8 1.63 1.97 .94 2300 3900 4200

W HEX

Male Branch Tee NPT Working Pressures

Thread (PSIG)
MBT Parker W H H1 R Stainless
Part No. Male Female Hex (in.) (in.) (in.) Brass Steel Steel
1-1-1 MBT 1/16 1/16 7/16 .50 .72 .38 3800 7000 7500
2-2-2 MBT 1/8 1/8 9/16 .66 .78 .38 2900 5500 5900
4-4-4 MBT 1/4 1/4 3/4 .88 1.09 .56 3000 5600 6000
6-6-6 MBT 3/8 3/8 7/8 1.02 1.22 .56 2700 5000 5300
8-8-8 MBT 1/2 1/2 1-1/16 1.23 1.47 .75 2500 4500 4800
12-12-12 MBT 3/4 3/4 1-5/16 1.36 1.59 .75 2000 3500 3700
16-16-16 MBT 1 1 1-5/8 1.63 1.97 .94 2300 3900 4200
H

H1 W HEX
R

Female Cross Working Pressures

NPT (PSIG)
FX Parker Thread W H Stainless
Part No. Female Hex (in.) Brass Steel Steel
1 FX 1/16 7/16 .50 3800 7000 7500
2 FX 1/8 9/16 .66 2900 5500 5900
4 FX 1/4 3/4 .88 3000 5600 6000
6 FX 3/8 7/8 1.06 2700 5000 5300
8 FX 1/2 1-1/16 1.23 2500 4500 4800
12 FX 3/4 1-5/16 1.36 2000 3500 3700
16 FX 1 1-5/8 1.63 2300 3900 4200
H

W HEX

Dimensions for reference only, subject to change.

10 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Instrument Pipe Fittings Table of
Contents

Pipe Cap NPT Working Pressures (PSIG)

Parker Thread W D Stainless
CP Part No. Female Hex (in.) Brass Steel Steel
1 CP 1/16 7/16 .50 4500 7500 8000
2 CP 1/8 9/16 .75 4000 6400 6800
4 CP 1/4 3/4 .91 4300 6600 7000
6 CP 3/8 7/8 1.03 3500 5300 5600
8 CP 1/2 1-1/16 1.34 3600 5200 5500
D
12 CP 3/4 1-1/4 1.44 3000 4300 4600
16 CP 1 1-5/8 1.63 3100 4500 4800

W HEX

Hex Head Plug NPT Working Pressures (PSIG)

Parker Thread W D R Stainless
PH Part No. Male Hex (in.) (in.) Brass Steel Steel
1 PH 1/16 3/8 .54 .38 6000 10000 10500
2 PH 1/8 7/16 .56 .38 5600 9100 9700
4 PH 1/4 9/16 .75 .56 4100 7500 8000
6 PH 3/8 11/16 .78 .56 4000 7200 7600
8 PH 1/2 7/8 .97 .75 3900 6600 7000
D
12 PH 3/4 1-1/16 1.06 .75 3800 6400 6800
16 PH 1 1-5/16 1.25 .94 2700 4600 4900

R
W HEX

Hollow Hex Plug W Working Pressures (PSIG)

Parker NPT Thread Internal D Stainless
PHH Part No. Male Hex (in.) Brass Steel Steel
1 PHH 1/16 5/32 .30 6000 10000 10500
2 PHH 1/8 3/16 .30 5600 9100 9700
4 PHH 1/4 1/4 .47 4100 7500 8000
D 6 PHH 3/8 5/16 .47 4000 7200 7600
8 PHH 1/2 3/8 .61 3900 6600 7000
12 PHH 3/4 9/16 .62 3800 6400 6800
16 PHH 1 5/8 .77 2700 4600 4900
INTERNAL
HOLLOW HEX

Dimensions for reference only, subject to change.

11 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Straight Thread Adapters Catalog 4260
Table of
Contents

Hex Head Plug *D2

Parker Interchanges Port Thd W D R Drill *L2
P5ON Part No. With UN/UNF-2A Hex (in.) (in.) (in.) (in.) O-Ring
4 P5ON 4 PST 7/16-20 9/16 0.67 0.36 0.203 0.41 3-904
6 P5ON 6 PST 9/16-18 11/16 0.73 0.39 0.297 0.44 3-906
8 P5ON 8 PST 3/4-16 7/8 0.80 0.44 0.422 0.44 3-908
12 P5ON 12 PST 1-1/16-12 1-1/4 1.09 0.59 0.656 0.59 3-912
16 P5ON 16 PST 1-5/16-12 1-1/2 1.13 0.59 0.875 0.50 3-916
D
*D2 drill and L2 depth are optional manufacturing method per SAE.
R

W HEX “O” RING

Hollow Hex Plug X

Parker Interchanges Port Thd Internal R D Dia.
HP5ON Part No. With UN/UNF-2A Hex (in.) (in.) (in.) O-Ring
P5ON 4 HP5ON 4 HPST 7/16-20 3/16 0.36 0.47 0.56 3-904
6 HP5ON 6 HPST 9/16-18 1/4 0.39 0.50 0.69 3-906
8 HP5ON 8 HPST 3/4-16 5/16 0.44 0.58 0.88 3-908
12 HP5ON 12 HPST 1-1/16-12 9/16 0.59 0.77 1.25 3-912
16 HP5ON 16 HPST 1-5/16-12 5/8 0.59 0.77 1.50 3-916
D
R
P5ON

“O” RING
INTERNAL
HOLLOW HEX

Straight Thread T2 T1 *D2

Parker Interchanges Port THD Port THD W Drill D R
Reducer/Expander Part No. With UN/UNF-2B UN/UNF-2A Hex (in.) (in.) (in.) O-Ring
F5OG5 HP5ON 6-4 F5OG5 6-RBST-4 7/16-20 9/16-18 11/16 .297 1.03 .36 3-904
8-4 F5OG5 8-RBST-4 7/16-20 3/4-16 7/8 .375 1.09 .36 3-904
12-8 F5OG5 12-RBST-8 3/4-16 1-1/16-12 1-1/4 .625 1.00 .44 3-908
16-12 F5OG5 16-RBST-12 1-1/16-12 1-5/16-12 1-1/2 .750 1.75 .59 3-912
*D2 drill is optional manufacturing method per SAE.
HP5ON
D
R

T2 T1

Dimensions
FHG5 for reference only, subject to change.

12 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Straight Thread Adapters Table of
Contents

Male SAE E ST
T1 T2 - NPT Minimum O-Ring
Straight Thread Parker Interchanges Straight Female D R Opening W Uniform
to Female NPT Part No. With Thread Size Pipe Size (in.) (in.) (in.) Hex Size #
4-4 GOA 4SAE-7-4 7/16-20 1/4 1.19 .36 .20 3/4 3-904
Thread 6-6 GOA 6SAE-7-6 9/16-18 3/8 1.26 .39 .30 7/8 3-906
GOA 8-8 GOA 8-SAE-7-8 3/4-16 1/2 1.50 .44 .39 1-1/8 3-908
12-12 GOA 12-SAE-7-12 1-1/16-12 3/4 1.83 .59 .66 1-1/4 3-912
16-16 GOA 16-SAE-7-16 1-5/16-12 1 1.88 .59 .88 1-5/8 3-916
Includes O-ring.

D
R

T2 T1

Male Connector Parker Parker Straight O-Ring

CPI™ A-LOK® Interchanges Tube Thread W A† C† D R Dash
to SAE Straight
FHG5
Part No. Part No. With O.D. Size Hex (in.) (in.) (in.) (in.) No.
Thread 4-4 ZH3BA 4-4 ZH3LA 400-IL-4ST 1/4 7/16-20 9/16 2.26 .70 1.97 .36 3-904
5-5 ZH3BA 5-5 ZH3LA 500-IL-5ST 5/16 1/2-20 5/8 2.32 .73 2.03 .36 3-905
6-6 ZH3BA 6-6 ZH3LA 600-IL-6ST 3/8 9/16-18 11/16 2.48 .76 2.19 .39 3-906
8-8 ZH3BA 8-8 ZH3LA 810-IL-8ST 1/2 3/4-16 7/8 2.99 .87 2.58 .44 3-908
FHG5 10-10 ZH3BA 10-10 ZH3LA 1010-IL-10ST 5/8 7/8-14 1 3.34 .87 2.94 .50 3-910
12-12 ZH3BA 12-12 ZH3LA 1210-IL-12ST 3/4 1-1/16-12 1-1/4 3.88 .87 3.48 .59 3-912
A
14-14 ZH3BA 14-14 ZH3LA 1410-IL-14ST 7/8 1-3/16-12 1-3/8 4.07 .87 3.67 .59 3-914
D 16-16 ZH3BA 16-16 ZH3LA 1610-IL-16ST 1 1-5/16-12 1-1/2 4.35 1.05 3.86 .59 3-916
C R Includes body, nut, ferrule and O-ring.
†Average value.

O-Ring Seals
All standard O-Rings are Nitrile material, 70 Durameter hardness.
For other materials state material after part number.

Dimensions for reference only, subject to change.

13 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Conversion Fittings Catalog 4260
Table of
Contents

Visual Index
BSPP Female/NPT Male BSP Taper Male Elbow BSPP Female Adapter
Visual Index for ....................................... page 19 ....................................... page 22 ....................................... page 25
Instrument Pipe Fittings
......................................... page 1

BSPP
ISO Fitting Nomenclature
....................................... page 15 BSP Taper Male Hex BSPP Female Gauge
Pipe Plug Adapter
Typical Fastening ....................................... page 20 BSPP Male Elbow ....................................... page 26
Threads (Positionable)
BSPT
....................................... page 16 ....................................... page 23

BSPP Thread Forms BSPP Parallel Male Hex

....................................... page 17
Pipe Plug
Sealing Washers
....................................... page 20
Bonded Seals
ISO Conversion (Stainless)
BSPT

Fittings BSPP Male Run Tee ....................................... page 26

(Positionable)
NPT Male/ ISO Thread/ ....................................... page 23
BSP Taper Male
....................................... page 18 Fractional Tube
Copper Washers/Male
Connectors ....................................... page 26

BSP Taper Male

Connector
NPT Male/BSPP Male ....................................... page 21
....................................... page 18 BSPP Male Branch Tee Copper Washers/Female
(Positionable) ....................................... page 26
BSPT

....................................... page 24

BSPP Male Connector

NPT Female/ ....................................... page 21
BSP Taper Male Thread and Tube End
....................................... page 18 Size Charts
................................ pages 27-29

BSP Taper Male Adapter

BSP Taper Female ....................................... page 24
Connector
NPT Female/BSPP Male ....................................... page 22 Pipe Data and
BSPT

....................................... page 19
Dimensions Chart
BSPT

....................................... page 30
BSPP Male Adapter
....................................... page 25
BSPP Female Gauge Engineering Report:
BSP Taper Female/
Connector Heat Code Traceability
NPT Male ....................................... page 22
....................................... page 19 ....................................... page 31
BSPPGC

BSP Taper Female

Adapter Offer of Sale
....................................... page 25 ................................ pages 35-36
BSPT

Visual Index for Instrument Pipe Fittings on page 1.

14
14 Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
ISO Conversion Fittings Table of
Contents

Parker ISO Fitting Nomenclature

Parker ISO Adapters utilize the same basic part numbering system that you are already familiar with from our
CPI™ and A-LOK® Catalogs. To specify a Parker Instrumentation Connector with an ISO thread form, simply suffix
the size designator with the thread form designator as illustrated.

Build a CPI™ or Pipe part number by filling in the following boxes:

(A) (B) (A) (B) (C) (D)
Port #1 Size Thread – Port #2 Size Thread – Shape – Material
Designator Designator Designator Designator Designator Designator

Build an A-LOK® part number by filling in the following boxes:

(A) (C) (A) (B) (D)
Port #1 Size Shape Port #2 Size Thread – Material
Designator Designator Designator Designator Designator

(A) Port Size Designators:

Port sizes are incremented by 1/16" 1 = 1/16" 6 = 3/8"
and only the numerator is required to 2 = 1/8" 8 = 1/2"
specify a size in a part number. 3 = 3/16" 10 = 5/8"
4 = 1/4" 12 = 3/4"
5 = 5/16" 16 = 1"    (larger sizes available)
(B) Thread Type Designators:
Leave Blank:  Fractional Tube Size
N* = NPT per ANSI B1.20.1
K = ISO Taper per; ISO 7/1, BS21, JIS B0203, DIN 2999
R = ISO Parallel per; ISO 228/1+2, DIN 3852 Form A, BS2779 (BSPP), JIS B0202
BR = ISO Parallel per; ISO 228/1+2, DIN 3852 Form B, BS2779 (BSPP), JIS B0202
GC = ISO Parallel, Female Gauge connector
* N thread type designator is only required for A-LOK® nomenclature

(C) Body Shape Designator:

FBZ = CPI™ Male Connector
MSC = A-LOK® Male Connector
RA = Pipe Reducing Adapter
MHN = Pipe Male Hex Nipple
See Catalog for further detail
Material Standard
(D) Material Designators: Stainless Steel
ASTM A276
SS = Stainless Steel for CPI™ and Pipe Fittings ASME SA 479
316 = Stainless Steel for A-LOK® ASTM B16
Brass
B = Brass ASTM B 453

Sealing
BSP Taper threads require the use of a thread sealant. BSPP threads require a sealing washer. This washer may
either be a metal gasket (copper is standard) or a “bonded seal” (elastomer bonded to a metal retaining washer).
The BSPP, form “A” requires the use of a bonded seal (page 26). The BSPP, form “B” (cutting face) may be
used with or without a sealing washer. For applications where the cutting face may not seal or where galling is a
potential problem, the use of a washer is suggested.

Examples: The Thread Type Designators have been highlighted in the following examples for easy recognition:
4-4K FBZ-SS 1/4" CPI™ tube fitting by 1/4" BSPT pipe thread
6-4R RA-SS 3/8" female NPT by 1/4" BSPP (form A) reducing adapter
A bonded seal should be used with this fitting (page 26).
6MSC4BR-316 3/8" A-LOK® tube fitting by 1/4" BSPP (form B)
A copper washer should be used with this fitting (page 26).

15 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Conversion Fittings Catalog 4260
Table of
Contents

Typical Fastening Threads American Standard Pipe Thread (NPT)

BSP threads

BSPP Parallel and BSP Taper threads have a thread

flank angle of 55° inclusive.

BSPP – British Standard Pipe Parallel threads for tubes 60° inclusive thread flank angle
and fittings where pressure-tight joints are not made on • Pitch measured in inches
the thread, i.e., a peripheral seal is used. • Truncation of root and crest are flat
• Taper angle 1°47'
BSP Taper – British Standard Pipe Taper threads for
tubes and fittings where pressure-tight joints are made
on the threads.
(ISO 7/1) BSPT

Comparison of Thread Forms

NPT BSPP BSPT
Thread Threads Threads
Size per Inch Thread Size per Inch
1/8 27 1/8 1/8 28
55° inclusive thread flank angle
• Pitch measured in inches
1/4 18 1/4 1/4 19 • Truncation of root and crest are round
3/8 18 3/8 3/8 19 • Taper angle 1°47'
1/2 14 1/2 1/2 14
3/4 14 3/4 3/4 14
(ISO 228/1) BSPP
1 11 1/2 1 1 11
1 1/4 11 1/2 1 1/4 1 1/4 11
1 1/2 11 1/2 1 1/2 1 1/2 11

Generic Thread 55° inclusive thread flank angle

PITCH
• Pitch measured in inches
• Truncation of root and crest are round
• Diameter measured in inches

MAJOR DIA.
PITCH DIA.
MINOR DIA.
FLANK ANGLE

16 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
ISO Conversion Fittings Table of
Contents

BSPP Thread Forms

Form A
A self centering taper is used at the hex which centers a “bonded” washer (usually metal and elastomer) to seal to
the surface surrounding the female thread.

Bonded
Seal

Form B
A metal gasket (usually copper) performs the seal between the face of the body and the face of the female
threaded c­ omponent. For Form “B” replace “R” in part number with “BR”.

Copper
Washer

Gauge Port BSPP (Female)

Copper
Copper
Washer
Washer

17 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Conversion Fittings Catalog 4260
Table of
Contents

Male Hex Nipple NPT BSPT Working Pressure

Parker Thread Thread W D R Brass Stainless Steel
NPT to BSP Taper Part No. T1 T2 Hex (in.) (in.) PSI Bar PSI Bar
2-2K MHN 1/8-27 1/8-28 7/16 1.06 .38 5600 390 9100 630
4-4K MHN 1/4-18 1/4-19 5/8 1.45 .56 4100 280 7500 520
6-6K MHN 3/8-18 3/8-19 3/4 1.45 .56 4000 280 7200 500
8-8K MHN 1/2-14 1/2-14 7/8 1.89 .75 3900 270 6600 460
D 12-12K MHN 3/4-14 3/4-14 1 1/8 1.97 .75 3800 260 6400 440
R R 16-16K MHN 1-11 1/2 1-11 1 3/8 2.34 .94 2700 190 4600 320
Used to connect a female NPT and a female BSPT threaded component.
T1 T2

Male Hex Nipple NPT BSPP Working Pressure

Parker Thread Thread W D R1 R2 Brass Stainless Steel
NPT to BSPP Part No. T1 T2 Hex (in.) (in.) (in.) PSI Bar PSI Bar
2-2R MHN 1/8-27 1/8-28 9/16 1.07 .38 .28 5000 340 9100 630
4-4R MHN 1/4-18 1/4-19 3/4 1.44 .56 .44 4000 280 7500 520
6-6R MHN 3/8-18 3/8-19 7/8 1.47 .56 .44 3900 270 7200 500
8-8R MHN 1/2-14 1/2-14 1 1/16 1.78 .75 .56 3800 260 6600 460
D 12-12R MHN 3/4-14 3/4-14 1 5/16 1.95 .75 .63 3600 250 6400 440
R1 R2 16-16R MHN 1-11 1/2 1-11 1 5/8 2.26 .94 .72 2600 180 4600 320
Used to connect a female NPT and a female BSPP threaded component.
T1 Note: Bonded seal, page 26, must be used on BSPP end shown.
T2
Please note the pressure ratings are based on taper threaded ends. The pressure rating for the BSPP
ends are dependent on the type of sealing washer used.

Female NPT to NPT BSPT Working Pressure

Thread Thread Brass Stainless Steel
Male BSP Taper Parker
Part No. T1 T2
W
Hex
D
(in.)
R
(in.) PSI Bar PSI Bar
Adapter 2-2K RA 1/8-27 1/8-28 9/16 1.09 .38 3200 220 6100 420
4-4K RA 1/4-18 1/4-19 3/4 1.42 .56 3300 230 6200 430
6-6K RA 3/8-18 3/8-19 7/8 1.49 .56 2600 180 5000 340
8-8K RA 1/2-14 1/2-14 1 1/16 1.94 .75 2400 160 4600 320
12-12K RA 3/4-14 3/4-14 1 5/16 2.00 .75 2300 160 4300 300
16-16K RA 1-11 1/2 1-11 1 5/8 2.28 .94 2200 150 4100 280
D
Used to connect a male NPT and a female BSPT threaded component.
R

T1 T2

Dimensions for reference only, subject to change.

18 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
ISO Conversion Fittings Table of
Contents

Female NPT to Male NPT BSPP Working Pressure

Thread Thread Brass Stainless Steel
BSPP Adapter Parker
Part No. T1 T2
W
Hex
D
(in.)
R
(in.) PSI Bar PSI Bar
2-2R RA 1/8-27 1/8-28 9/16 .99 .28 3200 220 6100 420
4-4R RA 1/4-18 1/4-19 3/4 1.31 .44 3300 230 6200 430
6-6R RA 3/8-18 3/8-19 7/8 1.41 .44 2600 180 5000 340
8-8R RA 1/2-14 1/2-14 1 1/8 1.74 .56 2400 160 4600 320
12-12R RA 3/4-14 3/4-14 1 5/16 2.00 .63 2300 160 4300 300
D
R
16-16R RA 1-11 1/2 1-11 1 5/8 2.10 .72 2200 150 4100 280
Used to connect a male NPT and a female BSPP threaded component.
Note: Bonded Seal, page 26, must be used with BSPP end shown.
T1 T2

Female BSP Taper to BSPT NPT

Working Pressure
Brass Stainless Steel
Male NPT Adapter Parker Thread Thread W D R
Part No. T1 T2 Hex (in.) (in.) PSI Bar PSI Bar
2K-2 RA 1/8-28 1/8-27 9/16 1.09 .38 3200 220 6100 420
4K-4 RA 1/4-19 1/4-18 3/4 1.42 .56 3300 230 6200 430
6K-6 RA 3/8-19 3/8-18 7/8 1.49 .56 2600 180 5000 340
8K-8 RA 1/2-14 1/2-14 1 1/8 1.94 .75 2400 160 4600 320
D 12K-12 RA 3/4-14 3/4-14 1 5/16 2.00 .75 2300 160 4300 300
R
16K-16 RA 1-11 1-11 1/2 1 5/8 2.28 .94 2200 150 4100 280
Used to connect a male BSPT and a female NPT threaded component.
T1 T2

Female BSPP to Male BSPP NPT Working Pressure

Thread Thread Brass Stainless Steel
NPT Adapter Parker
T1 T2
W D R
Part No. Hex (in.) (in.) PSI Bar PSI Bar
2R-2 RA 1/8-28 1/8-27 9/16 1.09 .38 3200 220 6100 420
4R-4 RA 1/4-19 1/4-18 3/4 1.50 .56 3300 230 6200 430
6R-6 RA 3/8-19 3/8-18 7/8 1.49 .56 2600 180 5000 340
8R-8 RA 1/2-14 1/2-14 1 1/8 1.88 .75 2400 160 4600 320
D 12R-12 RA 3/4-14 3/4-14 1 5/16 2.00 .75 2300 160 4300 300
R 16R-16 RA 1-11 1-11 1/2 1 5/8 2.28 .94 2200 150 4100 280
Used to connect a male BSPP and a female NPT threaded component.

T1 T2

19 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Conversion Fittings Catalog 4260
Table of
Contents

BSP Taper Male BSPT Working Pressure

Thread Brass Stainless Steel
Hex Pipe Plug Parker
T1
W D R
Part No. Hex (in.) (in.) PSI Bar PSI Bar
2K PH 1/8-28 7/16 .59 .38 3200 220 6100 420
4K PH 1/4-19 5/8 .81 .56 3300 230 6200 430
BSPT

6K PH 3/8-19 3/4 .81 .56 2600 180 5000 340

8K PH 1/2-14 7/8 1.06 .75 2400 160 3600 320
D 12K PH 3/4-14 1 1/8 1.13 .75 2300 160 4300 300
16K PH 1-11 1 3/8 1.31 .94 2200 150 4100 280
T1

R
W

BSPP Parallel Male BSPP Working Pressure

Brass Stainless Steel
Hex Pipe Plug Parker Thread W D R
Part No. T1 Hex (in.) (in.) PSI Bar PSI Bar
2R PH 1/8-28 9/16 .55 .28 5000 340 9100 630
4R PH 1/4-19 3/4 .78 .44 4000 280 7500 520
BSPT

6R PH 3/8-19 7/8 .78 .44 3900 270 7200 500

8R PH 1/2-14 1-1/16 .99 .56 3800 260 6600 460
D 12R PH 3/4-14 1-5/16 1.13 .63 3600 250 6400 440
R
16R PH 1-11 1-5/8 1.21 .72 2600 180 4600 320
Note: Bonded seal page 26 must be used on BSPP end shown.
Please note the pressure ratings are based on taper threaded ends. The pressure rating for the BSPP
BSPP

T1
ends are dependent on the type of sealing washer used.

Dimensions for reference only, subject to change.

20 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
ISO Threaded to Fractional Tube Connectors Table of
Contents

BSP Taper Male Tube Parker Parker

O.D. BSP CPI™ A-LOK® A C D R W
Connector (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex
1/8 1/8-28 2-2K FBZ 2MSC2K 1.20 .60 .94 .38 7/16
1/8 1/4-19 2-4K FBZ 2MSC4K 1.40 .60 1.14 .56 9/16
BSPT
1/4 1/8-28 4-2K FBZ 4MSC2K 1.30 .70 1.00 .38 1/2
1/4 1/4-19 4-4K FBZ 4MSC4K 1.50 .70 1.20 .56 9/16
1/4 3/8-19 4-6K FBZ 4MSC6K 1.52 .70 1.22 .56 11/16
A
1/4 1/2-14 4-8K FBZ 4MSC8K 1.76 .70 1.44 .75 7/8
C R
5/16 1/8-28 5-2K FBZ 5MSC2K 1.34 .73 1.05 .38 9/16
5/16 1/4-19 5-4K FBZ 5MSC4K 1.53 .73 1.23 .56 9/16
3/8 1/8-28 6-2K FBZ 6MSC2K 1.39 .76 1.09 .38 5/8
BSPT

3/8 1/4-19 6-4K FBZ 6MSC4K 1.59 .76 1.28 .56 5/8
3/8 3/8-19 6-6K FBZ 6MSC6K 1.59 .76 1.28 .56 11/16
W
D 3/8 1/2-14 6-8K FBZ 6MSC8K 1.82 .76 1.53 .75 7/8
1/2 1/4-19 8-4K FBZ 8MSC4K 1.75 .87 1.31 .56 13/16
1/2 3/8-19 8-6K FBZ 8MSC6K 1.75 .87 1.31 .56 13/16
1/2 1/2-14 8-8K FBZ 8MSC8K 1.93 .87 1.53 .75 7/8
Connects fractional tube to female ISO taper thread.

BSPP Male Tube Parker Parker

O.D. BSP CPI™ A-LOK® A C D R W
Connector (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex
1/8 1/8-28 2-2R FBZ 2MSC2R 1.18 .60 0.92 .28 9/16
1/8 1/4-19 2-4R FBZ 2MSC4R 1.38 .60 1.13 .44 3/4
1/8 3/8-19 2-6R FBZ 2MSC6R 1.43 .60 1.17 .44 7/8
1/4 1/8-28 4-2R FBZ 4MSC2R 1.28 .70 0.98 .28 9/16
1/4 1/4-19 4-4R FBZ 4MSC4R 1.49 .70 1.19 .44 3/4
A 1/4 3/8-19 4-6R FBZ 4MSC6R 1.55 .70 1.25 .44 7/8
C R 1/4 1/2-14 4-8R FBZ 4MSC8R 1.77 .70 1.47 .56 1 1/16
3/8 1/8-28 6-2R FBZ 6MSC2R 1.37 .76 1.06 .28 5/8
R 3/8 1/4-19 6-4R FBZ 6MSC4R 1.57 .76 1.25 .44 3/4
3/8 3/8-19 6-6R FBZ 6MSC6R 1.59 .76 1.30 .44 7/8
3/8 1/2-14 6-8R FBZ 6MSC8R 1.84 .76 1.53 .56 1 1/16
W
D 1/2 1/4-19 8-4R FBZ 8MSC4R 1.71 .87 1.28 .44 13/16
1/2 3/8-19 8-6R FBZ 8MSC6R 1.74 .87 1.30 .44 7/8
1/2 1/2-14 8-8R FBZ 8MSC8R 1.96 .87 1.53 .56 1 1/16
3/4 1/2-14 12-8R FBZ 12MSC8R 1.93 .87 1.53 .56 1 1/16
3/4 3/4-19 12-12R FBZ 12MSC12R 2.10 .87 1.69 .63 1 3/8
1 1/2-14 16-8R FBZ 16MSC8R 2.21 1.05 1.72 .56 1 3/8
1 1-11 16-16R FBZ 16MSC16R 2.37 1.05 1.88 .72 1 5/8
Connects fractional tube to female ISO parallel thread.
Note: Bonded Seal, page 26, must be used with BSPP end shown.

Dimensions for reference only, subject to change.

21 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Threaded to Fractional Tube Connectors Catalog 4260
Table of
Contents

BSP Taper Tube Parker Parker

O.D. BSPT CPI™ A-LOK® A C D W
Female (in.) Thread Part No. Part No. (in.) (in.) (in.) Hex
Connector 1/4 1/8-28 4-2K GBZ 4FSC2K 1.23 .70 .94 9/16
1/4 1/4-19 4-4K GBZ 4FSC4K 1.42 .70 1.13 3/4
1/4 3/8-19 4-6K GBZ 4FSC6K 1.48 .70 1.19 7/8
1/4 1/2-14 4-8K GBZ 4FSC8K 1.67 .70 1.38 1 1/16
BSPT
3/8 1/4-19 6-4K GBZ 6FSC4K 1.48 .76 1.19 3/4
3/8 3/8-19 6-6K GBZ 6FSC6K 1.54 .76 1.25 7/8
A 3/8 1/2-14 6-8K GBZ 6FSC8K 1.73 .76 1.44 1 1/16
C W 1/2 1/4-19 8-4K GBZ 8FSC4K 1.59 .87 1.19 13/16
1/2 3/8-19 8-6K GBZ 8FSC6K 1.65 .87 1.25 7/8
1/2 1/2-14 8-8K GBZ 8FSC8K 1.84 .87 1.44 1 1/16
BSPT

Connects fractional tube to male ISO taper thread.

BSPP Female Tube Parker Parker

O.D. BSPP CPI™ A-LOK® A C D W
Gauge Connector (in.) Thread Part No. Part No. (in.) (in.) (in.) Hex
1/4 1/4-19 4-4GC GBZ 4FSC4GC 1.48 .70 1.19 3/4
1/4 3/8-19 4-6GC GBZ 4FSC6GC 1.48 .70 1.19 7/8
BSPPGC

1/4 1/2-14 4-8GC GBZ 4FSC8GC 1.72 .70 1.42 1 1/16

5/16 1/4-19 5-4GC GBZ 5FSC4GC 1.51 .73 1.22 3/4
A
5/16 1/2-14 5-8GC GBZ 5FSC8GC 1.61 .73 1.32 1 1/16
C W 3/8 1/4-19 6-4GC GBZ 6FSC4GC 1.54 .76 1.25 3/4
3/8 3/8-19 6-6GC GBZ 6FSC6GC 1.53 .76 1.23 7/8
3/8 1/2-14 6-8GC GBZ 6FSC8GC 1.65 .76 1.36 1 1/16
BSPPGC

1/2 3/8-19 8-6GC GBZ 8FSC6GC 1.75 .87 1.35 7/8

1/2 1/2-14 8-8GC GBZ 8FSC8GC 1.90 .87 1.50 1 1/16
D Connects fractional tube to male ISO parallel (gauge).
Note: Copper Washer, page 26, for female thread sealing, must be used on BSPP female end shown.

BSP Taper Male Tube Parker Parker

O.D. BSPT CPI™ A-LOK® C H L R W
Elbow (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex
1/4 1/8-28 4-2K CBZ 4MSEL2K 1.06 .74 .77 .38 1/2
1/4 1/4-19 4-4K CBZ 4MSEL4K 1.08 1.00 .78 .56 9/16
1/4 3/8-19 4-6K CBZ 4MSEL6K 1.17 1.13 .88 .56 3/4
1/4 1/2-14 4-8K CBZ 4MSEL8K 1.26 1.31 .97 .75 7/8
5/16 1/4-19 5-4K CBZ 5MSEL4K 1.11 1.00 .81 .56 5/8
3/8 1/8-28 6-2K CBZ 6MSEL2K 1.20 .82 .91 .38 5/8
3/8 1/4-19 6-4K CBZ 6MSEL4K 1.20 1.01 .91 .56 5/8
3/8 3/8-19 6-6K CBZ 6MSEL6K 1.26 1.13 .97 .56 3/4
C 1/2 3/8-19 8-6K CBZ 8MSEL6K 1.42 1.15 1.02 .56 13/16
L 8-8K CBZ 8MSEL8K
W HEX 1/2 1/2-14 1.42 1.30 1.02 .75 7/8
Connects fractional tube to female ISO taper thread.

Dimensions for reference only, subject to change.

22 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
ISO Threaded to Fractional Tube Connectors Table of
Contents

BSPP Male Elbow Tube Parker Parker

O.D. BSPP CPI™ A-LOK® C H L R W
(Positionable) (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex
1/4 1/8-28 4-2R CBZ 4MSEL2R 1.06 1.04 .77 .63 9/16
1/4 1/4-19 4-4R CBZ 4MSEL4R 1.14 1.27 .85 .79 9/16
3/8 1/4-19 6-4R CBZ 6MSEL4R 1.14 1.27 .85 .79 9/16
3/8 3/8-19 6-6R CBZ 6MSEL6R 1.50 1.46 1.02 .79 3/4
1/2 1/4-19 8-4R CBZ 8MSEL4R 1.50 1.38 1.10 .79 7/8
1/2 3/8-19 8-6R CBZ 8MSEL6R 1.50 1.46 1.10 .79 7/8
1/2 1/2-14  8-8R CBZ 8MSEL8R 1.50 1.71 1.10 1.03 7/8
C 5/8 1/2-14 10-8R CBZ 10MSEL8R 1.50 1.81 1.10 1.03 1 1/16
L W HEX 3/4 1/2-14 12-8R CBZ 12MSEL8R 1.57 1.81 1.17 1.03 1 1/16
3/4 3/4-14 12-12R CBZ 12MSEL12R 1.57 1.92 1.17 1.03 1 1/16
1 3/4-14 16-12R CBZ 16MSEL12R 1.94 2.11 1.45 1.03 1 5/16
1 1-11 16-16R CBZ 16MSEL16R 1.94 2.11 1.45 1.20 1 5/16
H Connects fractional tube to female ISO parallel thread.
L4N
R
“O” RING

STRAIGHT
THREAD

BSPP Male Run Tee Tube Parker Parker

O.D. BSPP CPI™ A-LOK® C H L R W
(Positionable) (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex  
1/4 1/8-28 4-2R-4 RBZ 4MRT2R 1.06 1.04 .77 .63 9/16
1/4 1/4-19 4-4R-4 RBZ 4MRT4R 1.14 1.27 .85 .79 9/16
3/8 1/4-19 6-4R-6 RBZ 6MRT6R 1.20 1.27 .91 .79 9/16
1/2 3/8-19 8-6R-8 RBZ 8MRT8R 1.50 1.46 1.10 .79 7/8
1/2 1/2-14 8-8R-8 RBZ  8MRT8R 1.50 1.71 1.10 1.03 7/8
5/8 1/2-14 10-8R-10 RBZ 10MRT8R 1.50 1.81 1.10 1.03 1 1/16
3/4 1/2-14 12-8R-12 RBZ 12MRT8R 1.57 1.81 1.17 1.03 1 1/16
3/4 3/4-14 12-12R-12 RBZ 12MRT12R 1.57 1.92 1.17 1.03 1 1/16
C H 1 1-11 16-16R-16 RBZ 16MRT16R 1.94 2.11 1.45 1.20 1 5/16
L R Connects fractional tube to female ISO parallel thread.

W L4N “O” RING

Dimensions for reference only, subject to change.

23 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Threaded to Fractional Tube Connectors Catalog 4260
Table of
Contents

BSPP Male Branch Tube Parker Parker

O.D. BSPP CPI™ A-LOK® C H L R W
Tee (Positionable) (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex
1/4 1/8-28 4-4-2R SBZ 4MBT2R 1.06 1.04 .77 .63 9/16
1/4 1/4-19 4-4-4R SBZ 4MBT4R 1.14 1.27 .85 .79 9/16
3/8 1/4-19 6-6-4R SBZ 6MBT4R 1.14 1.27 .85 .79 9/16
1/2 3/8-19 8-8-6R SBZ 8MBT6R 1.50 1.46 1.10 .79 7/8
1/2 1/2-14 8-8-8R SBZ 8MBT8R 1.50 1.71 1.10 1.03 7/8
5/8 1/2-14 10-10-8R SBZ 10MBT8R 1.50 1.81 1.10 1.03 1 1/16
3/4 1/2-14 12-12-8R SBZ 12MBT8R 1.57 1.81 1.17 1.03 1 1/16
3/4 3/4-14 12-12-12R SBZ 12MBT12R 1.57 1.92 1.17 1.03 1 1/16
C
L 1 1-11 16-16-16R SBZ 16MBT16R 1.94 2.11 1.45 1.20 1 5/16
Connects fractional tube to female ISO parallel thread.

W HEX
H
L4N R

“O” RING

BSP Taper Male Tube Parker Parker CPI™ A-LOK® Min.

O.D. BSPT CPI™ A-LOK® A K A K R W Bore
Adapter (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) (in.) Hex (in.)
1/8 1/8-28 2-2K T2HF 2MA2K 1.16 0.54 1.16 .54 .38 7/16 .078
1/8 1/4-19 2-4K T2HF 2MA4K 1.39 0.54 1.39 .54 .56 9/16 .281
BSPT

1/4 1/8-28 4-2K T2HF 4MA2K 1.27 0.64 1.25 .63 .38 7/16 .156
1/4 1/4-19 4-4K T2HF 4MA4K 1.49 0.64 1.46 .63 .56 9/16 .078
A
5/16 1/8-28 5-2K T2HF 5MA2K 1.32 0.68 1.28 .66 .38 7/16 .219
K R 5/16 1/4-19 5-4K T2HF 5MA4K 1.53 0.68 1.49 .66 .56 9/16 .219
3/8 1/4-19 6-4K T2HF 6MA4K 1.57 0.72 1.53 .69 .56 9/16 .281
3/8 3/8-19 6-6K T2HF 6MA6K 1.61 0.72 1.56 .69 .56 11/16 .281
BSPT

3/8 1/2-14 6-8K T2HF 6MA8K 1.82 0.72 1.78 .69 .75 7/8 .281
1/2 1/4-19 8-4K T2HF 8MA4K 1.84 0.98 1.75 .91 .75 9/16 .281
W 8-6K T2HF 8MA6K
1/2 3/8-19 1.87 0.98 1.78 .91 .56 11/16 .375
1/2 1/2-14 8-8K T2HF 8MA8K 2.09 0.98 2.00 .91 .75 7/8 .375
5/8 3/8-19 10-6K T2HF 10MA6K 1.91 1.03 1.84 .97 .56 11/16 .469
5/8 1/2-14 10-8K T2HF 10MA8K 2.14 1.03 2.06 .97 .75 7/8 .469
3/4 3/4-14 12-12K T2HF 12MA12K 2.14 1.03 2.06 .97 .75 1 1/16 .594
1 1-11 16-16K T2HF 16MA16K 2.68 1.30 2.60 1.22 .94 1 3/8 .813
Connects fractional tube to female ISO taper thread.
Generic, annealed tube stub for effective ferrule sealing.

Dimensions for reference only, subject to change.

24 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
ISO Threaded to Fractional Tube Connectors Table of
Contents

BSPP Male Tube Parker Parker CPI™ A-LOK® Min.

O.D. BSPP CPI™ A-LOK® A K A K R W Bore
Adapter (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) (in.) Hex (in.)h
1/8 1/8-28 2-2R T2HF 2MA2R 1.16 .54 1.16 .54 .28 9/16 .078
1/8 1/4-19 2-4R T2HF 2MA4R 1.37 .54 1.37 .54 .44 3/4 .078
1/4 1/8-28 4-2R T2HF 4MA2R 1.26 .64 1.31 .63 .28 9/16 .156
1/4 1/4-19 4-4R T2HF 4MA4R 1.48 .64 1.50 .63 .44 3/4 .156
A 3/8 1/4-19 6-4R T2HF 6MA4R 1.56 .72 1.57 .69 .44 3/4 .281
K R 3/8 3/8-19 6-6R T2HF 6MA6R 1.59 .72 1.60 .69 .44 7/8 .281
1/2 1/4-19 8-4R T2HF 8MA4R 1.81 .98 1.79 .91 .44 3/4 .375
1/2 3/8-19 8-6R T2HF 8MA6R 1.85 .98 1.82 .91 .44 7/8 .375
1/2 1/2-14 8-8R T2HF 8MA8R 2.10 .98 1.94 .91 .44 1-1/8 .375
3/4 3/4-14 12-12R T2HF 12MA12R 2.22 1.03 2.16 .97 .63 1-3/8 .594
W
1 1-11 16-16R T2HF 16MA16R 2.67 1.30 2.54 1.22 .72 1-3/4 .813
Connects fractional tube end to female ISO parallel thread.
Note: Bonded Seal, page 26 must be used on BSPP end shown.
Generic, annealed tube stub for effective sealing.

BSP Taper Female Tube Parker Parker CPI™ A-LOK® Min.

O.D. BSPT CPI™ A-LOK® A K A K W Bore
Adapter (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex (in.)
1/4 1/8-28 4-2K T2HG 4FA2K 1.31 .64 1.30 .63 9/16 .156
1/4 1/4-19 4-4K T2HG 4FA4K 1.48 .64 1.45 .63 3/4 .156
BSPT

3/8 1/4-19 6-4K T2HG 6FA4K 1.56 .72 1.50 .69 3/4 .281
3/8 3/8-19 6-6K T2HG 6FA6K 1.63 .72 1.59 .69 7/8 .281
1/2 1/4-19 8-4K T2HG 8FA4K 1.83 .98 1.71 .91 3/4 .375
A
K 1/2 3/8-19 8-6K T2HG 8FA6K 1.89 .98 1.80 .91 7/8 .375
1/2 1/2-14 8-8K T2HG 8FA8K 2.14 .98 2.05 .91 1-1/16 .375
BSPT

Connects fractional tube end to male ISO taper thread.

Note: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response.

BSPP Female Tube Parker Parker CPI™ A-LOK® Min.

O.D. BSPP CPI™ A-LOK® A K A K W Bore
Adapter (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex (in.)
1/8 1/8-28 2-2R T2HG 2FA2R 1.21 .54 1.21 .54 9/16 .078
1/4 1/8-28 4-2R T2HG 4FA2R 1.31 .64 1.25 .63 9/16 .156
BSPP

1/4 1/4-19 4-4R T2HG 4FA4R 1.48 .64 1.50 .63 3/4 .156
3/8 1/4-19 6-4R T2HG 6FA4R 1.56 .72 1.55 .69 3/4 .281
3/8 3/8-19 6-6R T2HG 6FA6R 1.63 .72 1.57 .69 7/8 .281
A
1/2 3/8-19 8-6R T2HG 8FA6R 1.89 .98 1.78 .91 7/8 .375
K
1/2 1/2-14 8-8R T2HG 8FA8R 2.14 .98 1.95 .91 1-1/16 .375
Connects fractional tube end to male ISO parallel thread.
BSPP

Note: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response.

Dimensions for reference only, subject to change.

25 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
ISO Threaded to Fractional Tube Connectors Catalog 4260
Table of
Contents

BSPP Female Tube Parker Parker CPI™ A-LOK® Min.

O.D. BSPP CPI™ A-LOK® A K A K W Bore
Gauge Adapter (in.) Thread Part No. Part No. (in.) (in.) (in.) (in.) Hex (in.)
1/4 1/4-19 4-4GC T2HG 4FA4GC 1.48 .64 1.34 .63 3/4 .156
3/8 3/8-19 6-6GC T2HG 6FA6GC 1.63 .72 1.55 .69 7/8 .281
1/2 1/2-14 8-8GC T2HG 8FA8GC 2.14 .98 1.92 .91 1 1/16 .375
Connects fractional tube end to male ISO parallel thread (gauge).
Note: Copper Washer, shown below, for female thread sealing, must be used on BSPP female end shown.
A Note: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response.
K

Sealing Washers
Bonded Seals T Pressure Ratings For Sealing Washers
Consists of an outer stainless steel ring BSPP D H Thread Size PSI Bar
with a bonded Viton® inner ring used to
seal a male ISO parallel thread.
Part No. Thread (in.) (in.) 1/8 5300 370
M30201-SS 1/8 .63 .08 1/4 5500 380
M30202-SS 1/4 .81 .08 3/8 4400 300
M30203-SS 3/8 .94 .08 1/2 4000 280
M30204-SS 1/2 1.12 .10 3/4 3700 260
M30206-SS 3/4 1.38 .10 1 2800 190
M30208-SS 1 1.69 .10
H These seals are also available in steel with a Nitrile inner ring.
Simply replace Suffix SS with S.
T
D

Copper For BSPP male thread sealing For BSPP female thread sealing

Washers D* d H D d H
Part No. Thread (in.) (in.) (in.) Part No. Thread (in.) (in.) (in.)
M28329 1/8 .71 .39 .09 M25179 1/8 0.322 0.188 0.062
M28330 1/4 .87 .55 .09 M25180 1/4 0.436 0.250 0.062
M28331 3/8 .94 .67 .09 M25181 3/8 0.574 0.375 0.062
M28332 1/2 1.18 .87 .10 M25182 1/2 0.719 0.500 0.062
H M28334 3/4 1.38 1.06 .09 M25184 3/4 0.935 0.719 0.062
d M28336 1 1.65 1.34 .09 M25186 1 1.178 0.969 0.093
D Used to provide a seal with male or female parallel ISO threads.
* Gasket fits ISO 1179-1 type G/H port.

Please note the pressure ratings are based on taper threaded ends. The pressure
rating for the BSPP ends are dependent on the type of sealing washer used.

Dimensions for reference only, subject to change.

26 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Thread & Tube End Size Chart (USA) Table of
Contents

27 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Pipe & Tube End Size Chart (USA) Catalog 4260
Table of
Contents

28 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Thread & Tube End Size Chart (Int'l) Table of
Contents

29 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Pipe Data and Dimensions Catalog 4260
Table of
Contents

Pipe Data and Dimensions

Dimensions
Pipe Iron Outside Inside Wall
Size Schedule Pipe Diameter Diameter Thickness
(Inches) # Size (Inches) (Inches) (Inches)
– – 0.307 0.049
1/8 40 STD 0.405 0.269 0.068
80 XS 0.215 0.095
– – 0.410 0.065
1/4 40 STD 0.540 0.364 0.088
80 XS 0.302 0.119
– – 0.545 0.065
3/8 40 STD 0.675 0.493 0.091
80 XS 0.423 0.126
– – 0.710 0.065
– – 0.674 0.083
40 STD 0.622 0.109
1/2 0.840
80 XS 0.546 0.147
160 – 0.466 0.187
– XXS 0.252 0.294
– – 0.920 0.065
– – 0.884 0.083
40 STD 0.824 0.113
3/4 1.050
80 XS 0.742 0.154
160 – 0.612 0.219
– XXS 0.434 0.308
– – 1.185 0.065
– – 1.097 0.109
40 STD 1.049 0.133
1 1.315
80 XS 0.957 0.179
160 – 0.815 0.25
– XXS 0.599 0.358
– – 1.530 0.065
– – 1.442 0.109
40 STD 1.38 0.140
1-1/4 1.660
80 XS 1.278 0.191
160 – 1.160 0.250
– XXS 0.896 0.382
– – 1.770 0.065
– – 1.682 0.109
40 STD 1.610 0.145
1-1/2 1.900
80 XS 1.500 0.200
160 – 1.338 0.281
– XXS 1.100 0.400
– – 2.245 0.065
– – 2.157 0.109
40 STD 2.067 0.154
2 2.375
80 XS 1.939 0.218
160 – 1.687 0.344
– XXS 1.503 0.436

30 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Engineering Report Table of
Contents

Heat Code Traceability

Parker Hannifin’s Instrumentation Connectors Division • HCT relieves the user of Parker instrumentation tube
offers Heat Code Traceability (HCT) on CPI™, ­fittings of any doubts. It acts as an assurance for
A-LOK®, Instrumentation Pipe, and Weld-Lok fittings. today and for tomorrow.

HCT refers to the fact that a specific part can be The material used in Parker Hannifin instrumentation
traced back to the original mill heat of metal from fitting components is 316 or 316L (welded products)
which it was made. Beginning with the original melt, stainless steel as specified and referenced in Section
a package of documents is created which completely III of the ASME Boiler and Pressure Vessel code.
describes the metal in physical and chemical terms.
The end result is that a number, which is permanently The American Society of Mechanical Engineers
stamped to the part, refers back to the document (ASME) Boiler and Vessel Code, Section III, latest
package. issue, entitled Rules for Construction of Nuclear
Power Plant Components, is the principal document
The HCT number is stamped on the material (bar covering this type of fitting in the nuclear field. ANSI
stock or forging) prior to manufacturing. The concept Standard B.31.1.0, Power Piping, and ANSI Standard
is useful because it provides a method for complete B.31.7, Nuclear Power Piping, are also important
material accountability for the manufacturer and end documents in the field.
customer.
In addition to the documentation of chemical and
HCT offers these advantages: physical properties, great care is taken throughout
the manufacture of Parker’s tube fittings to ensure
• Raw materials for manufacture must meet code that potential stress corrosion will not be a problem in
requirements. This can be verified through normal usage of the parts. Manu­facturing processes
documentation so that the customer is certain that avoid exposure of the parts to mercury or halogens,
what is ordered is received. and control of thermal treatment avoids the condition
known as continuous grain boundary carbide
• HCT provides a record of chemical analysis with the
precipitation.
raw material. Thus, in areas requiring welding, the
correct welding technique is applied.

For additional information please contact your local authorized Parker Instrumentation distributor
or call Parker Instrumentation Connectors Division and ask for Bulletin 4230-B15.

31 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Notes Catalog 4260
Table of
Contents

32 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Notes Table of
Contents

33 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Notes Catalog 4260
Table of
Contents

34 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Catalog 4260
Offer of Sale Table of
Contents

Offer of Sale
The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, its
subsidiaries and its authorized distributors (“Seller”) are hereby offered for sale at prices to be established by Seller. This offer
and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order
for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this
offer. All goods or work described will be referred to as “Products”.
1. Terms and Conditions. Seller’s willingness to offer be allowed unless asserted in writing within 60 days after
Products, or accept an order for Products, to or from Buyer is delivery or, in the case of an alleged breach of warranty,
expressly conditioned on Buyer’s assent to these Terms and within 30 days after the date within the warranty period on
Conditions and to the terms and conditions found on-line at which the defect is or should have been discovered by Buyer.
www.parker.com/saleterms/. Seller objects to any contrary Any action based upon breach of this agreement or upon
or additional term or condition of Buyer’s order or any other any other claim arising out of this sale (other than an action
document issued by Buyer. by Seller for any amount due to Seller from Buyer) must be
2. Price Adjustments; Payments. Prices stated on the commenced within thirteen months from the date of tender
reverse side or preceding pages of this document are valid of delivery by Seller or, for a cause of action based upon
for 30 days. After 30 days, Seller may change prices to reflect an alleged breach of warranty, within thirteen months from
any increase in its costs resulting from state, federal or local the date within the warranty period on which the defect is or
legislation, price increases from its suppliers, or any change should have been discovered by Buyer.
in the rate, charge, or classification of any carrier. The prices 6. LIMITATION OF LIABILITY. UPON NOTIFICATION,
stated on the reverse or preceding pages of this document SELLER WILL, AT ITS OPTION, REPAIR OR REPLACE A
do not include any sales, use, or other taxes unless so stated DEFECTIVE PRODUCT, OR REFUND THE PURCHASE
specifically. Unless otherwise specified by Seller, all prices PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO
are F.O.B. Seller’s facility, and payment is due 30 days from BUYER FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
the date of invoice. After 30 days, Buyer shall pay interest CONSEQUENTIAL DAMAGES ARISING OUT OF, OR AS
on any unpaid invoices at the rate of 1.5% per month or the THE RESULT OF, THE SALE, DELIVERY, NON-DELIVERY,
maximum allowable rate under applicable law. SERVICING, USE OR LOSS OF USE OF THE PRODUCTS
3. Delivery Dates; Title and Risk; Shipment. All delivery OR ANY PART THEREOF, OR FOR ANY CHARGES OR
dates are approximate and Seller shall not be responsible EXPENSES OF ANY NATURE INCURRED WITHOUT
for any damages resulting from any delay. Regardless of the SELLER’S WRITTEN CONSENT, EVEN IF SELLER HAS
manner of shipment, title to any products and risk of loss BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR
or damage shall pass to Buyer upon tender to the carrier OTHER LEGAL THEORY. IN NO EVENT SHALL SELLER’S
at Seller’s facility (i.e., when it’s on the truck, it’s yours). LIABILITY UNDER ANY CLAIM MADE BY BUYER EXCEED
Unless otherwise stated, Seller may exercise its judgment THE PURCHASE PRICE OF THE PRODUCTS.
in choosing the carrier and means of delivery. No deferment 7. Contingencies. Seller shall not be liable for any default
of shipment at Buyers’ request beyond the respective or delay in performance if caused by circumstances beyond
dates indicated will be made except on terms that will the reasonable control of Seller.
indemnify, defend and hold Seller harmless against all loss 8. User Responsibility. The user, through its own analysis
and additional expense. Buyer shall be responsible for any and testing, is solely responsible for making the final
additional shipping charges incurred by Seller due to Buyer’s selection of the system and Product and assuring that all
changes in shipping, product specifications or in accordance performance, endurance, maintenance, safety and warning
with Section 13, herein. requirements of the application are met. The user must
4. Warranty. Seller warrants that the Products sold here- analyze all aspects of the application and follow applicable
under shall be free from defects in material or workmanship for industry standards and Product information. If Seller provides
a period of twelve months from the date of delivery to Buyer Product or system options, the user is responsible for
or 2,000 hours of normal use, whichever occurs first. This determining that such data and specifications are suitable
warranty is made only to Buyer and does not extend to anyone and sufficient for all applications and reasonably foreseeable
to whom Products are sold after purchased from Seller. The uses of the Products or systems.
prices charged for Seller’s products are based upon the 9. Loss to Buyer’s Property. Any designs, tools, patterns,
exclusive limited warranty stated above, and upon the following materials, drawings, confidential information or equipment
disclaimer: DISCLAIMER OF WARRANTY: THIS WARRANTY furnished by Buyer or any other items which become Buyer’s
COMPRISES THE SOLE AND ENTIRE WARRANTY property, may be considered obsolete and may be destroyed
PERTAINING TO PRODUCTS PROVIDED HEREUNDER. by Seller after two consecutive years have elapsed without
SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS Buyer placing an order for the items which are manufactured
AND IMPLIED, INCLUDING MERCHANTABILITY AND using such property. Seller shall not be responsible for
FITNESS FOR A PARTICULAR PURPOSE. any loss or damage to such property while it is in Seller’s
5. Claims; Commencement of Actions. Buyer shall possession or control.
promptly inspect all Products upon delivery. No claims for 10. Special Tooling. A tooling charge may be imposed for
shortages will be allowed unless reported to the Seller any special tooling, including without limitation, dies, fixtures,
within 10 days of delivery. No other claims against Seller will molds and patterns, acquired to manufacture Products.

35 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to
Offer of Sale Catalog 4260
Table of
Contents

Such special tooling shall be and remain Seller’s property by written notice immediately terminate this agreement for
notwithstanding payment of any charges by Buyer. In no event the following: (a) Buyer commits a breach of any provision of
will Buyer acquire any interest in apparatus belonging to Seller this agreement (b) the appointment of a trustee, receiver or
which is utilized in the manufacture of the Products, even if custodian for all or any part of Buyer’s property (c) the filing of
such apparatus has been specially converted or adapted for a petition for relief in bankruptcy of the other Party on its own
such manufacture and notwithstanding any charges paid by behalf, or by a third party (d) an assignment for the benefit of
Buyer. Unless otherwise agreed, Seller shall have the right to creditors, or (e) the dissolution or liquidation of the Buyer.
alter, discard or otherwise dispose of any special tooling or 18. Governing Law. This agreement and the sale and
other property in its sole discretion at any time. delivery of all Products hereunder shall be deemed to have
11. Buyer’s Obligation; Rights of Seller. To secure taken place in and shall be governed and construed in
payment of all sums due or otherwise, Seller shall retain a accordance with the laws of the State of Ohio, as applicable to
security interest in the goods delivered and this agreement contracts executed and wholly performed therein and without
shall be deemed a Security Agreement under the Uniform regard to conflicts of laws principles. Buyer irrevocably agrees
Commercial Code. Buyer authorizes Seller as its attorney and consents to the exclusive jurisdiction and venue of the
to execute and file on Buyer’s behalf all documents Seller courts of Cuyahoga County, Ohio with respect to any dispute,
deems necessary to perfect its security interest. Seller shall controversy or claim arising out of or relating to this agreement.
have a security interest in, and lien upon, any property of Disputes between the parties shall not be settled by arbitration
Buyer in Seller’s possession as security for the payment of unless, after a dispute has arisen, both parties expressly agree
any amounts owed to Seller by Buyer. in writing to arbitrate the dispute.
12. Improper use and Indemnity. Buyer shall indemnify, 19. Indemnity for Infringement of Intellectual Property
defend, and hold Seller harmless from any claim, liability, Rights. Seller shall have no liability for infringement of
damages, lawsuits, and costs (including attorney fees), any patents, trademarks, copyrights, trade dress, trade
whether for personal injury, property damage, patent, secrets or similar rights except as provided in this Section.
trademark or copyright infringement or any other claim, Seller will defend and indemnify Buyer against allegations
brought by or incurred by Buyer, Buyer’s employees, or any of infringement of U.S. patents, U.S. trademarks, copyrights,
other person, arising out of: (a) improper selection, improper trade dress and trade secrets (“Intellectual Property Rights”).
application or other misuse of Products purchased by Buyer Seller will defend at its expense and will pay the cost of any
from Seller; (b) any act or omission, negligent or otherwise, settlement or damages awarded in an action brought against
of Buyer; (c) Seller’s use of patterns, plans, drawings, or Buyer based on an allegation that a Product sold pursuant to
specifications furnished by Buyer to manufacture Product; or this Agreement infringes the Intellectual Property Rights of a
(d) Buyer’s failure to comply with these terms and conditions. third party. Seller’s obligation to defend and indemnify Buyer is
Seller shall not indemnify Buyer under any circumstance contingent on Buyer notifying Seller within ten (10) days after
except as otherwise provided. Buyer becomes aware of such allegations of infringement, and
13. Cancellations and Changes. Orders shall not be Seller having sole control over the defense of any allegations or
subject to cancellation or change by Buyer for any reason, actions including all negotiations for settlement or compromise.
except with Seller’s written consent and upon terms that If a Product is subject to a claim that it infringes the Intellectual
will indemnify, defend and hold Seller harmless against all Property Rights of a third party, Seller may, at its sole expense
direct, incidental and consequential loss or damage. Seller and option, procure for Buyer the right to continue using
may change product features, specifications, designs and the Product, replace or modify the Product so as to make it
availability with notice to Buyer. noninfringing, or offer to accept return of the Product and return
the purchase price less a reasonable allowance for depreciation.
14. Limitation on Assignment. Buyer may not assign its Notwithstanding the foregoing, Seller shall have no liability
rights or obligations under this agreement without the prior for claims of infringement based on information provided by
written consent of Seller. Buyer, or directed to Products delivered hereunder for which the
15. Entire Agreement. This agreement contains the entire designs are specified in whole or part by Buyer, or infringements
agreement between the Buyer and Seller and constitutes resulting from the modification, combination or use in a system
the final, complete and exclusive expression of the terms of of any Product sold hereunder. The foregoing provisions of
the agreement. All prior or contemporaneous written or oral this Section shall constitute Seller’s sole and exclusive liability
agreements or negotiations with respect to the subject matter and Buyer’s sole and exclusive remedy for infringement of
are herein merged. Intellectual Property Rights.
16. Waiver and Severability. Failure to enforce any 20. Taxes. Unless otherwise indicated, all prices and
provision of this agreement will not waive that provision nor charges are exclusive of excise, sales, use, property,
will any such failure prejudice Seller’s right to enforce that occupational or like taxes which may be imposed by any taxing
provision in the future. Invalidation of any provision of this authority upon the manufacture, sale or delivery of Products.
agreement by legislation or other rule of law shall not invalidate 21. Equal Opportunity Clause. For the performance of
any other provision herein. The remaining provisions of this government contracts and where dollar value of the Products
agreement will remain in full force and effect. exceed $10,000, the equal employment opportunity clauses
17. Termination. This agreement may be terminated by in Executive Order 11246, VEVRAA, and 41 C.F.R. §§ 60-
Seller for any reason and at any time by giving Buyer thirty 1.4(a), 60-741.5(a), and 60-250.4, are hereby incorporated.
(30) days written notice of termination. In addition, Seller may
01/09

36 Parker Hannifin Corporation

Instrumentation Products Division
Huntsville, AL USA
http://www.parker.com/ipdus
 Go to

Parker’s Motion & Control Technologies

Table of
Contents

At Parker, we’re guided by

a relentless drive to help
our customers become more
productive and achieve
higher levels of profitabil-
ity by engineering the best
systems for their require-
ments. It means looking at
customer applications from
AEROSPACE CLIMATE CONTROL ELECTROMECHANICAL FILTRATION
many angles to find new Key Markets Key Markets Key Markets Key Markets
ways to create value. What- • Aircraft engines • Agriculture • Aerospace • Food & beverage
• Business & general aviation • Air conditioning • Factory automation • Industrial machinery
ever the motion and control • Commercial transports • Food, beverage & dairy • Life science & medical • Life sciences
technology need, Parker has • Land-based weapons systems • Life sciences & medical • Machine tools • Marine
• Military aircraft • Precision cooling • Packaging machinery • Mobile equipment
the experience, breadth of • Missiles & launch vehicles • Processing • Paper machinery • Oil & gas
product and global reach • Regional transports • Transportation • Plastics machinery & converting • Power generation
• Unmanned aerial vehicles • Primary metals • Process
to consistently deliver. No Key Products • Semiconductor & electronics • Transportation
company knows more about Key Products • CO2 controls • Textile
• Flight control systems • Electronic controllers • Wire & cable Key Products
motion and control technol- & components • Filter driers • Analytical gas generators
ogy than Parker. For further • Fluid conveyance systems • Hand shut-off valves Key Products • Compressed air & gas filters
• Fluid metering delivery • Hose & fittings • AC/DC drives & systems • Condition monitoring
info call 1-800-C-Parker. & atomization devices • Pressure regulating valves • Electric actuators, gantry robots • Engine air, fuel & oil filtration
• Fuel systems & components • Refrigerant distributors & slides & systems
• Hydraulic systems & components • Safety relief valves • Electrohydrostatic actuation systems • Hydraulic, lubrication &
• Inert nitrogen generating systems • Solenoid valves • Electromechanical actuation systems coolant filters
• Pneumatic systems & components • Thermostatic expansion valves • Human machine interface • Process, chemical, water
• Wheels & brakes • Linear motors & microfiltration filters
• Stepper motors, servo motors, • Nitrogen, hydrogen & zero
drives & controls air generators
• Structural extrusions

FLUID & GAS HANDLING HYDRAULICS PNEUMATICS PROCESS CONTROL SEALING & SHIELDING
Key Markets Key Markets Key Markets Key Markets Key Markets
• Aerospace • Aerospace • Aerospace • Chemical & refining • Aerospace
• Agriculture • Aerial lift • Conveyor & material handling • Food, beverage & dairy • Chemical processing
• Bulk chemical handling • Agriculture • Factory automation • Medical & dental • Consumer
• Construction machinery • Construction machinery • Life science & medical • Microelectronics • Energy, oil & gas
• Food & beverage • Forestry • Machine tools • Oil & gas • Fluid power
• Fuel & gas delivery • Industrial machinery • Packaging machinery • Power generation • General industrial
• Industrial machinery • Mining • Transportation & automotive • Information technology
• Mobile • Oil & gas Key Products • Life sciences
• Oil & gas • Power generation & energy Key Products • Analytical sample • Military
• Transportation • Truck hydraulics • Air preparation conditioning products • Semiconductor
• Welding • Brass fittings & valves & systems • Telecommunications
Key Products • Manifolds • Fluoropolymer chemical • Transportation
Key Products • Diagnostic equipment • Pneumatic accessories delivery fittings, valves
• Brass fittings & valves • Hydraulic cylinders • Pneumatic actuators & grippers & pumps Key Products
• Diagnostic equipment & accumulators • Pneumatic valves & controls • High purity gas delivery • Dynamic seals
• Fluid conveyance systems • Hydraulic motors & pumps • Quick disconnects fittings, valves & regulators • Elastomeric o-rings
• Industrial hose • Hydraulic systems • Rotary actuators • Instrumentation fittings, • EMI shielding
• PTFE & PFA hose, tubing & • Hydraulic valves & controls • Rubber & thermoplastic hose valves & regulators • Extruded & precision-cut,
plastic fittings • Power take-offs & couplings • Medium pressure fittings fabricated elastomeric seals
• Rubber & thermoplastic hose • Rubber & thermoplastic hose • Structural extrusions & valves • Homogeneous & inserted elastomeric
& couplings & couplings • Thermoplastic tubing & fittings • Process control manifolds shapes
• Tube fittings & adapters • Tube fittings & adapters • Vacuum generators, cups & sensors • High temperature metal seals
• Quick disconnects • Quick disconnects • Metal & plastic retained composite
seals
• Thermal management
 Go to
Table of
Parker Worldwide Contents

Europe, Middle East, Africa HU – Hungary, Budaörs ZA – South Africa, Kempton Park
Tel: +36 23 885 470 Tel: +27 (0)11 961 0700
AE – United Arab Emirates, parker.hungary@parker.com parker.southafrica@parker.com
Dubai
Tel: +971 4 8127100 IE – Ireland, Dublin
parker.me@parker.com Tel: +353 (0)1 466 6370 North America
parker.ireland@parker.com CA – Canada, Milton, Ontario
AT – Austria, Wiener Neustadt
Tel: +43 (0)2622 23501-0 IT – Italy, Corsico (MI) Tel: +1 905 693 3000
parker.austria@parker.com Tel: +39 02 45 19 21 US – USA, Cleveland
parker.italy@parker.com Tel: +1 216 896 3000
AT – Eastern Europe, Wiener
Neustadt KZ – Kazakhstan, Almaty
Tel: +43 (0)2622 23501 900 Tel: +7 7273 561 000 Asia Pacific
parker.easteurope@parker.com parker.easteurope@parker.com
AU – Australia, Castle Hill
AZ – Azerbaijan, Baku NL – The Netherlands, Oldenzaal Tel: +61 (0)2-9634 7777
Tel: +994 50 2233 458 Tel: +31 (0)541 585 000
parker.azerbaijan@parker.com parker.nl@parker.com CN – China, Shanghai
Tel: +86 21 2899 5000
BE/LU – Belgium, Nivelles NO – Norway, Asker
Tel: +32 (0)67 280 900 Tel: +47 66 75 34 00 HK – Hong Kong
parker.belgium@parker.com parker.norway@parker.com Tel: +852 2428 8008

BG – Bulgaria, Sofia PL – Poland, Warsaw IN – India, Mumbai

Tel: +359 2 980 1344 Tel: +48 (0)22 573 24 00 Tel: +91 22 6513 7081-85
parker.bulgaria@parker.com parker.poland@parker.com JP – Japan, Tokyo
BY – Belarus, Minsk PT – Portugal, Leca da Palmeira Tel: +81 (0)3 6408 3901
Tel: +375 17 209 9399 Tel: +351 22 999 7360 KR – South Korea, Seoul
parker.belarus@parker.com parker.portugal@parker.com Tel: +82 2 559 0400
CH – Switzerland, Etoy RO – Romania, Bucharest MY – Malaysia, Shah Alam
Tel: +41 (0)21 821 87 00 Tel: +40 21 252 1382 Tel: +60 3 7849 0800
parker.switzerland@parker.com parker.romania@parker.com
NZ – New Zealand, Mt Wellington
CZ – Czech Republic, Klecany RU – Russia, Moscow Tel: +64 9 574 1744
Tel: +420 284 083 111 Tel: +7 495 645-2156
parker.russia@parker.com SG – Singapore
parker.czechrepublic@parker.com
Tel: +65 6887 6300
DE – Germany, Kaarst SE – Sweden, Spånga
Tel: +46 (0)8 59 79 50 00 TH – Thailand, Bangkok
Tel: +49 (0)2131 4016 0
parker.sweden@parker.com Tel: +662 186 7000-99
parker.germany@parker.com
SK – Slovakia, Banská Bystrica TW – Taiwan, Taipei
DK – Denmark, Ballerup
Tel: +421 484 162 252 Tel: +886 2 2298 8987
Tel: +45 43 56 04 00
parker.denmark@parker.com parker.slovakia@parker.com
ES – Spain, Madrid SL – Slovenia, Novo Mesto South America
Tel: +34 902 330 001 Tel: +386 7 337 6650 AR – Argentina, Buenos Aires
parker.spain@parker.com parker.slovenia@parker.com Tel: +54 3327 44 4129
FI – Finland, Vantaa TR – Turkey, Istanbul BR – Brazil, Sao Jose dos Campos
Tel: +358 (0)20 753 2500 Tel: +90 216 4997081 Tel: +55 800 727 5374
parker.finland@parker.com parker.turkey@parker.com
CL – Chile, Santiago
FR – France, Contamine s/Arve UA – Ukraine, Kiev Tel: +56 2 623 1216
Tel: +33 (0)4 50 25 80 25 Tel +380 44 494 2731
MX – Mexico, Toluca
parker.france@parker.com parker.ukraine@parker.com
Tel: +52 72 2275 4200
GR – Greece, Athens UK – United Kingdom, Warwick
Tel: +30 210 933 6450 Tel: +44 (0)1926 317 878
parker.greece@parker.com parker.uk@parker.com

© 2014 Parker Hannifin Corporation. All rights reserved. Catalog 4260 05/2014-DDP
(05/2014-Duke)
Parker Hannifin Corporation
Instrumentation Products Division
1005 A Cleaner Way
Huntsville, AL 35805
phone 256 881 2040
fax 256 881 5072
www.parker.com/ipdus Your local authorized Parker distributor