Fosroc Nitoflor Conductive constructive solutions
Epoxy resin static conductive floor with resistance between Properties
5x104 and 1x106 ohms
The test results below were determined on laboratory
Uses specimens and may vary from those obtained under site
conditions.
Nitoflor Conductive is suitable for use in areas where a static
Electrical Properties
conductive floor with a resistance between 5x104 and 1x106
Surface resistance : 5x104 to 1x106 ohms
ohms is required as a measure to control static electricity,
(ASTM F150-78)
such as:
Bulk resistance
Electronic manufactire and assembly (DIN 51953) : 5x104 to 1x106 ohms
hospital operation theatre (ASTM F150-78) 5x104 to 1x106 ohms
hazardous dust and chemical environments Charge decay
clean rooms etc. (Fed. Spec. 101C : 5000v to zero in less than
Method 4046) 0.1 seconds
Advantages Body voltage decay : 5000v to zero in 0.4
(Stephen Halperin seconds using conductive
Static control - provides static electricity with an effective & Associate Ltd.) heel straps or shoes.
passage to earth.
Physical properties
Seamless - smooth, hygienic surface which is easily Compressive strength
cleaned, unlike vinyl tiles which are not seamless. (BS6319) : 60 N/mm²
Flexural strength
Durable - long term performance, accepts fork lift traffic,
(BS6319) : 40 N/mm²
more durable than vinyl tiles.
Tensile strength
Attractive - wide range of colours enhances working (BS6319) : 18 N/mm²
environment. Abrasion resistance
Fed. Spec. 141A (CS17 97mg weight loss
Resists most chemical spillage.
wheel,1000g, 1000cycles) 0.03mm depth of water
Impact resistance
Description
(BS8204 Pt.1) : 0.2mm indentation
Nitoflor Conductive is a 2mm thick epoxy resin floor topping Cure time 20°C 35°C
with controlled conductive properties. Foot traffic 24 hours 18 hours
Vehicular traffic 48 hours 36 hours
The system comprises an epoxy primer, conductive epoxy
Reaction to fire : Class B
undercoat and a 2mm thick epoxy top coat. It is available in a
(ASTM E84/UL723)
wide range of attractive colours and provides a highly durable,
(for Flame Spread Index(FSI) and Smoke Development
chemically resistant seamless floor.
Index(SDI))
Technical support Chemical properties
Fosroc offers a comprehensive technical support service to Nitoflor Conductive provides excellent resistance to a wide
specifiers, end users and contractors. It is also able to offer range of industrial chemicals.
on-site technical assistance, an AutoCAD facility and
dedicated specification assistance in locations all over the Design Criteria
world.
Nitoflor Conductive is designed for application at a nominal
thickness of 2mm. It should be installed where a static
Specification
conductive floor with resistance between 5x104 and 1x106
The designated floor areas shall be surfaced with Nitoflor ohms is required.
Conductive, a 2mm thick flow-applied epoxy resin floor
Nitoflor Conductive is designed to dissipate static electricity
Nitoflor Conductive
topping. The topping shall provide a surface and bulk
away from the source to earth.
resistance between 5x104 and 1x106 ohms when tested to
DIN 51953 and ASTM F150-78 respectively. Substrates should be dry and not suffer, or be likely to suffer,
from rising damp. If necessary, suitable damp-proof
membranes should be installed to prevent this. Substrates
Fosroc Nitoflor Conductive
Instructions for use Storage
Nitoflor Conductive should be installed by specialist All products above have a shelf life of 12 months if kept in a
applicators who must follow the proceedures laid down in dry store in their original unopened packages.
the Method Statement. Please contact your local Fosroc
Store in cool, dry conditions in original unopened packs. If
representative to obtain the Method Statement for correct
stored at high temperature and/or high humidity conditions,
application of Nitoflor Conductive.
the shelf life will be reduced.
Limitations
Precautions
- Application should not commence if the temperature of
Health and safety
the substrate is below 10°C.
Nitoflor Conductive, Nitoflor Conductive undercoat, Nitoprime
- Nitoflor Conductive should not be used on floors known
31 and Fosroc Solvent 102 should not come in contact with
to suffer from rising damp or have a relative humidity
skind and eyes, or be swallowed. Ensure adequate
greater than 75% when measured in accrdance with BS
ventiallation and avoid inhalation of vapours. Some people
8203:87, appendix A or by a Vaisala thermohygrometer
are sensitive to resins, hardeners and solvents. Wear suitable
type 131.
protective clothing, gloves and eye protection. If working in
- Ensure adequate cover is taken to avoid exposing the confined areas, suitable respiratory protective equipment
material to a “wind tunnel” effect. must be used. The use of a barrier cream provide addtional
skin protection. In case of contact with skin, rinse with plenty
- Nitoflor Conductive shoud not be applied to asphalt,
of clean water, then cleanse with soap and water. Do not use
unmodified sand/cement screeds, PVC tiles or vinyl.
solvent. In case of contact with eyes, rinse immediately with
plenty of clean water and seek medical advice. If swallowed
Estimating
seek medical attention immediately - Do not induce vomitting.
Supply
Fire
Nitoflor Conductive : 15 litre
Nitoflor Conductive U/C : 4.5 litre Nitoflor Conductive base component, Nitoflor Conductive
Nitoprime 31 : 1 & 4 lt can undercoat and Nitoprime 31 are non-flammable.
Fosroc Solvent 102 : 5 litre pails
Nitoprime Conductive Hardener component,and Fosroc
Coverage/Yield Solvent 102 are flammable.
Nitoflor Conductive : 7 to 7.5m² / 15 litre Flash points
Nitoflor Conductive U/C : 15-20m²/ 4.5 litre
Nitoflor Conductive hardener : 39°C
Nitoprime 31 : 4-5m²/litre
Fosroc Solvent 102 : 33°C
* Denotes the trademark of Fosroc International Limited
†
See separate data sheet
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to
obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
www.fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com
UAE/0443/12/C
