R.

46
X2 CLASS (EN132400) - MKP Series
METALLIZED POLYPROPYLENE FILM CAPACITOR
SELF-HEALING PROPERTIES
Typical applications: interference suppression and
«across-the-line» applications. Suitable for use in situations
where failure of the capacitor would not lead to danger of
electric shock.
PRODUCT CODE: R46

Loose Taped Insulated rigid leads Insulated flexible leads 0.5mm2

Fig.1 Fig.2

p 15 22.5p27.5 p = 37.5

∅ d 0 05
0.05
0.6 0.8 1
All dimensions are in mm.

GENERAL TECHNICAL DATA TEST METHOD AND PERFORMANCE

Dielectric: polypropylene film. Damp heat, steady state:
Test conditions 1st
Plates: metal layer deposited by evaporation under vacuum.
Temperature: +40_C2_C
Winding: non-inductive type. Relative humidity (RH): 93% 2%
Leads: tinned wire. Test duration: 56 days
Test conditions 2nd
Protection: plastic case, epoxy resin filled. Box material is
solvent resistant and flame retardant according to UL94 V0. Temperature: +60_C2_C
Relative humidity (RH): 95% 2%
Marking : Manufacturer’s logo, series, capacitance, tolerance, Test duration: 500 hours
rated voltage, capacitor class, dielectric code, climatic category,
passive flammability category, manufacturing date code, Performance
approvals, manufacturing plant. Dielectric strength:
no dielectric breakdown or
flashover at 4.3×VR (d.c.)/1 min
Climatic category: 40/110/56 IEC 60068-1
Capacitance change |∆C/C|: ≤5%
Operating temperature range: -40 to +110_C Insulation resistance: ≥50% of initial limit.
Related documents: IEC 60384-14 2nd edition ’93; Endurance:
EN 132400. Test conditions

ELECTRICAL CHARACTERISTICS Temperature: +110_C2_C

Test duration: 1000 h
Rated voltage (VR): 275Vac; 50/60Hz Voltage applied: 1.25×VR +1000Vac 0.1 s/h
Performance
Capacitance range: 0.01mF to 4.7mF
Dielectric strength:no dielectric breakdown or
Capacitance values: E6 series (IEC 60063 Norm). flashover at 4.3×VR (d.c.)/1 min
Capacitance change |∆C/C|: ≤10%
Capacitance tolerances (measured at 1 kHz):
Insulation resistance: ≥50% of initial limit.
10% (K); 20% (M).
Resistance to soldering heat:
Dissipation factor (DF): Test conditions
tgδ×10-4 at +25_C 5_C: ≤10 (6)* at 1kHz Solder bath temperature: +260_C5_C
* Typical value Dipping time (with heat screen):10 s1 s
Performance
Insulation resistance:
Test conditions Capacitance change |∆C/C|: ≤2%
Temperature: +25_C5_C
Winding scheme
Voltage charge time: 1 min
Voltage charge: 100 Vdc
Performance
≥1×105 MΩ (5×105 MΩ )* for C≤0.33mF
≥30000 s (150000 s )* for C>0.33mF
single sided metallized
* Typical value polypropylene film
Test voltage between terminations (on all pieces):
1500Vac for 1 s + 2200Vdc for 1 s at +25_C5_C
112 Last revised in May 2001
 R.46
X2 CLASS (EN132400) - MKP Series
METALLIZED POLYPROPYLENE FILM CAPACITOR
SELF-HEALING PROPERTIES

(All dimensions are in mm) APPROVALS

Max
Rated 275 Vac dv/dt at
390Vdc Part Number ENEC-IMQ
Cap. (*) EN132400 Class X2 File No. V4413
B H L p (V/ ms) (*) CB File No. IT-1524
0.010 mF 5.0 11.0 13.0 10.0 500 R46.KF. 2100.- -.M1. -
0.015 mF 5.0 11.0 13.0 10.0 500 R46.KF. 2150.- -.M1. - CSA C22.2 N_1
Across-the-line File No. LR 83890
(up to 1mF)
0.022 mF 5.0 11.0 13.0 10.0 500 R46.KF. 2220.- -.M1. -
0.033 mF 5.0 11.0 13.0 10.0 500 R46.KF. 2330.- -.M1. - UL 1414
Across-the-line File No.E97797
0.047 mF 6.0 12.0 13.0 10.0 500 R46.KF. 2470.- -.M1. - (up to 1mF)
0.010 mF 5.0 11.0 18.0 15.0 400 R46.KI. 2100.- -.01. - Electromagnetic
0.015 mF 5.0 11.0 18.0 15.0 400 R46.KI. 2150.- -.01. - UL 1283
Interference File No.E85238
(310 Vac)
0.022 mF 5.0 11.0 18.0 15.0 400 R46.KI. 2220.- -.01. - Filters
0.033 mF 5.0 11.0 18.0 15.0 400 R46.KI. 2330.- -.01. -
0.047 mF 5.0 11.0 18.0 15.0 400 R46.KI. 2470.- -.01. - CCEE IEC60384-14 Class X2 File No.CH0045034-2000
0.068 mF 5.0 11.0 18.0 15.0 400 R46.KI. 2680.- -.01. -
0.10 mF 5.0 11.0 18.0 15.0 400 R46.KI. 3100.- -.M1.M
CSA and UL 1414 for 250Vac only.
0.10 mF 6.0 12.0 18.0 15.0 400 R46.KI. 3100.- -.01. -
0.15 mF 6.0 12.0 18.0 15.0 400 R46.KI. 3150.- -.M2.M
Approved according to EN 132400 (IEC 60384-14 2nd
0.15 mF 7.5 13.5 18.0 15.0 400 R46.KI. 3150.- -.M1. - edition 1993 plus Amendment A1: 1995).
0.22 mF 7.5 13.5 18.0 15.0 400 R46.KI. 3220.- -.M2.M According to IEC 60065.
0.22 mF 8.5 14.5 18.0 15.0 400 R46.KI. 3220.- -.M1. -
0.33 mF 10.0 16.0 18.0 15.0 400 R46.KI. 3330.- -.M1. - (*) ENEC mark has replaced all the following European
0.47 mF 11.0 19.0 18.0 15.0 400 R46.KI. 3470.- -.M1. - National marks:
0.15 mF 6.0 15.0 26.5 22.5 200 R46.KN. 3150.- -.01. -
0.22 mF 6.0 15.0 26.5 22.5 200 R46.KN. 3220.- -.M1. -
0.33 mF 7.0 16.0 26.5 22.5 200 R46.KN. 3330.- -.M1. -
0.47 mF 8.5 17.0 26.5 22.5 200 R46.KN. 3470.- -.M1. -
0.47 mF 10.0 18.5 26.5 22.5 200 R46.KN. 3470.- -.01. -
0.68 mF 10.0 18.5 26.5 22.5 200 R46.KN. 3680.- -.M2. -
0.68 mF 11.0 20.0 26.5 22.5 200 R46.KN. 3680.- -.M1. -
1.0 mF 13.0 22.0 26.5 22.5 200 R46.KN. 4100.- -.M1. -
0.47 mF 9.0 17.0 32.0 27.5 150 R46.KR. 3470.- -.01. -
0.68 mF 9.0 17.0 32.0 27.5 150 R46.KR. 3680.- -.M1. -
0.68 mF 10.0 20.0 32.0 27.5 150 R46.KR. 3680.- -.01. -
1.0 mF 11.0 20.0 32.0 27.5 150 R46.KR. 4100.- -.M1. -
1.5 mF 13.0 22.0 32.0 27.5 150 R46.KR. 4150.- -.M1. -
1.5 mF 15.0 24.5 32.0 27.5 150 R46.KR. 4150.- -.01. -
2.2 mF 14.0 28.0 32.0 27.5 150 R46.KR. 4220.- -.M1. -
2.2 mF 18.0 33.0 32.0 27.5 150 R46.KR. 4220.- -.01. -
3.3 mF 18.0 33.0 32.0 27.5 150 R46.KR. 4330.- -.M2. -
3.3 mF 22.0 37.0 32.0 27.5 150 R46.KR. 4330.- -.M1. -
4.7 mF 22.0 37.0 32.0 27.5 150 R46.KR. 4470.- -.M1. -
2.2 mF 13.0 24.0 41.5 37.5 100 R46.KW.4220.- -.M1. -
3.3 mF 16.0 28.5 41.5 37.5 100 R46.KW.4330.- -.M1. -
4.7 mF 19.0 32.0 41.5 37.5 100 R46.KW.4470.- -.M1. -

Mechanical version and packaging (Table 1)

Tolerance: K (10%); M (20%)

(*) E12 series available up to 5.6mF upon request TYPICAL GRAPHS

Z = f (f) (lead length 2 mm). Typical values.
Table 1
Standard Lead Taping style Ordering Z [Ω ]
packaging style length code 1000

P2 Fig. Pitch
(Digit 10 to 11)
(mm) (mm) (No.) (mm) 100

AMMO--PACK 12.70 1 10.0/15.0 DQ

AMMO--PACK 19.05 2 22.5 DQ 10

REEL ⊘355mm 12.70 1 10.0/15.0 CK

1 0.0 1µ F
REEL ⊘500mm 19.05 2 22.5/27.5 CK
Loose, short leads 04 +2 00
0 .1
Loose, long leads 30 +5 50
0 .0 1 µ F
p.1 0
Loose, insulated
0 .1 µ F
30 +5 51 0 .0 1 1 µF
0.3 3 µ F
p.2 2. 5
p. 15

rigid leads
4 .7 µF p. 27 .5
p. 37 .5

Loose, insulated
1505 52 0 .0 0 1
flexible leads 0 .1 1 10 100
F [M H z ]
Note: Ammo-pack is the preferred packaging for taped version.

113 Last revised in March 2000