(3) Pin Definition of Serial Communication (4) Parts Names

DOP-B10S615 / DOP-B10E615 COM1 Port (Supports Flow Control) DOP-B10S615 炾 DOP-B10E615 (Front View)
Contact
COM Port PIN
RS-232
1

DOP-B10
PIN1
2 RXD
High ColorɄ
ɄWide ScreenɄ 3 TXD
4
User-Friendly HMI Products 5 GND
6

B10S615 / B10E615 Instrunction Sheet

7 RTS
8 CTS
9
(1) Preface Note: Blank = No Connection.

Thank you for purchasing DELTA’s DOP-B series. This instruction sheet will be helpful in the installation, wiring and C
inspection of Delta HMI. Before using the product, please read this instruction sheet to ensure correct use. You should
thoroughly understand all safety precautions before proceeding with the installation, wiring and operation. Place this
instruction sheet in a safe location for future reference. Please observe the following precautions:
„ Install the product in a clean and dry location free from corrosive and inflammable gases or liquids. DOP-B10S615 / DOP-B10E615 COM2 Port (Supports Flow Control)
„ Ensure that all wiring instructions and recommendations are followed. MODE1 MODE2 MODE3
COM Port PIN
„ Ensure that HMI is correctly connected to a ground. The grounding method must comply with the electrical RS-232 RS-422 RS-485
standard of the country (Please refer to NFPA 70: National Electrical Code, 2005 Ed.). 1 TXD+ D+
„ Do not disassemble HMI, modify or remove wiring when power is applied to HMI. PIN1 A
2 RXD
„ Do not touch the power supply during operation. Otherwise, it may cause electric shock. 3 TXD B
If you have any questions during operation, please contact our local distributors or Delta sales representatives. 4 RXD+
The content of this instruction sheet may be revised without prior notice. Please consult our distributors or download 5 GND GND GND : Power LED Indicator
the most updated version at http://www.delta.com.tw/ia 6 TXD- D- A
7 RTS Lights in green when HMI works normally.

(2) Safety Precautions 8

9
CTS
RXD- : Operation LED Indicator (Blue) (Note1)

Carefully note and observe the following safety precautions when receiving, inspecting, installing, operating, Note1: Blank = No Connection.
maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are used to mark safety Note2: When COM2 port is used for RS-232 flow control, i.e. RTS and CTS signals are used for flow control, COM3 port will The operation LED indicator blinks in blue when either the communication is carried
precautions when using the Delta’s HMI product. Failure to observe these precautions may void the warranty! become incapable of being used.
Note3: When COM2 port is used for RS-422 flow control, please refer to the following COM3 Port signals table for pin B out or the data is accessing (please refer to the “Note1” below for explanation).
assignments. The signals, RTS+, CTS+, RTS- and CTS- shown in brackets are the signals used for flow control.
Installation
: Alarm LED Indicator (Red)
¾ Comply with quick start for installation. Otherwise it may cause equipment damage.
¾ Do not install the product in a location that is outside the stated specification for the HMI. The alarm LED indicator blinks in red when one of the alarms is on.
Failure to observe this caution may result in electric shock, fire, or explosion.
¾ Do not install the product in a location where temperatures will exceed specification for DOP-B10S615 / DOP-B10E615 COM3 Port
the HMI. Failure to observe this caution may result in abnormal operation or damage the C Touch Screen / Display
product. MODE1 MODE2 MODE3
COM Port PIN
¾ Please note that this equipment has obtained EMC registration for commercial use. In the RS-232 RS-422 RS-485
event that it has been mistakenly sold or purchased, please exchange it for equipment 1 TXD+(RTS+) D+ NOTE
certified for home use. PIN1 2 RXD
¾ Do not use this product as an alarm device for disaster early warning that may result in 3 TXD 1. The definition of the operation LED indicator (Blue) can be determined by the users freely.
personal injury, equipment damage, or system emergency stop.
4 RXD+(CTS+)
Wiring 5 GND GND GND
6 TXD-(RTS-) D- DOP-B10S615炾DOP-B10E615 (Rear View)
¾ Connect the ground terminals to a class-3 ground (Ground resistance should not exceed 7
100ȍ). Improper grounding may result in communication error, electric shock or fire. 8
9 RXD-(CTS-)
Operation Note1: Blank = No Connection.
Note2: When COM2 port is used for RS-422 flow control, please refer to the COM3 Port signals table above for pin assignments.
¾ The users should use Delta Screen Editor software to perform editing in Delta's HMI The signals, RTS+, CTS+, RTS- and CTS- shown in brackets are the signals used for flow control.
product. To perform editing and confirming HMI programs without using Delta Screen G
Editor software in Delta's HMI product may result in abnormal operation.
¾ To prevent the personal injury and equipment damage, when designing HMI programs,
please ensure that a communication error occurred between Delta’s HMI product and the
DOP-B10E615 Ethernet Interface (LAN)
connecting controller or equipment will not result in system failure or malfunction.
¾ Please be sure to backup the screen data and HMI programs in case they are lost, Contact
accidentally deleted or worse. Ethernet Interface (LAN) PIN
Ethernet
1 TX+
¾ Do not modify wiring during operation. Otherwise it may result in electric shock or H
personal injury. 2 TX-
¾ Never use a hard or pointed object to hit or strike the screen as doing this may damage the 3 RX+
4 I
screen and let the screen has not respond at all, and then cause HMI to work abnormally.
5 J
Maintenance and Inspection
6 RX-
¾ Do not touch any internal or exposed parts of the HMI as electrical shock may result. 7 A
¾ Do not remove operation panel while power is on. Otherwise electrical shock may result. 8
¾ Wait at least 10 minutes after power has been removed before touching any HMI terminals
or performing any wiring and/or inspection as an electrical charge may still remain in the Note: Blank = No Connection.
HMI with hazardous voltages even after power has been removed. B
¾ Turn the power off before changing backup battery and check system settings after C D E F
finishing change. (all data will be cleared after changing battery).
¾ Be sure the ventilation holes are not obstructed during operation. Otherwise malfunction A Power Input Terminal F Ethernet Interface (LAN)
may result due to bad ventilation or overheating troubles.
COM2
Wiring Method

¾ Do not use a voltage that will exceed specification for the HMI. Failure to observe this (It is provided with two LED indicators to
caution may result in electric shock or fire. B G Memory Card Slot / Battery Cover
¾ Remove the terminal block from the HMI before wiring. indicate that HMI is in Read or Write status
¾ Insert only one wire into one terminal on the terminal block.
¾ If the wiring is in error, perform the wiring again with proper tools. Never use force to
remove the terminals or wires. Otherwise, it may result in malfunction or damage.
during the communication process.)
¾ For the power line that forced to take out, ensure to check wiring again and restart.
COM3
Communication Wiring

¾ Comply with communication wiring specification for wiring. (It is provided with two LED indicators to
¾ Wiring length should comply with the stated specification for the HMI. C H USB Host
¾ Proper grounding to avoid bad communication quality. indicate that HMI is in Read or Write status
¾ To avoid noise and interference, the communication cable, all power cables, and motor
power cable should be placed in separate conduits.
during the communication process.)

D COM1 I Audio Output Interface

E USB Slave J System Key

 (5) Dimensions
o o
Operation Temp. 0 C ~ 50 C
o o
DOP-B10S615 / DOP-B106515 Storage Temp. -20 C ~ +60 C
10% ~ 90% RH [0 ~ 40oC], 10% ~ 55% RH [41 ~ 50oC]
Ambient Humidity
261.3+1.0 +0.04"
0 (10.29" 0 ) Pollution Degree 2
IEC 61131-2 compliant 5Hzʀf烋8.3Hz = Continuous: 3.5mm, 8.3Hzʀfʀ
Vibration
150Hz = Continuous: 1.0g
IEC 60068-2-27 compliant 15g peak for 11 ms duration, X, Y, Z directions
Shock
for 6 times
Dimensions

)
Note:

+0.04"
T=1.6mm(0.063")~6mm(0.24") 272 x 200 x 61
(W) x (H) x (D) mm

0 (7.45" 0
272(10.71")
51.9(2.04")
T Panel Cutout
261.3 X 189.3

189.3+1.0
(W) x (H) mm
Weight Approx.1520g

NOTE

188.3(7.41")
200(7.88")
1) The half-life of backlight is defined as original luminance being reduced by 50% when the maximum driving current is
o
supplied to HMI. The life of LED backlight shown here is an estimated value under 25 C normal temperature and humidity
conditions.
2) USB Host port can provide up to 5V/ 500mA of power.
3) The withstand voltage of the isolated power circuit is 1500V peak for 1 minute.
4) Some models are in the process of application to UL and KCC certification. For more information, please consult our
distributors.
Units: mm (inches) 5) The value of the power consumption indicates the electrical power consumed by HMI only without connecting to any
peripheral devices. In order to ensure the normal operation, it is recommended to use a power supply which the capacity is
1.5 ~2 times the value of the power consumption.
6) The content of this quick start may be revised without prior notice. Please consult our distributors or download the most
(6) Specifications updated version at http://www.delta.com.tw/ia/.

Model DOP-B10S615 DOP-B10E615

10.1” Widescreen TFT LCD
Display Type
(65536 colors)
MODULE

Resolution 1024 x 600 pixels

LCD

Backlight LED Back Light (less than 10,000 hours half-life at 25oC) (Note 1)

Display Size 226 x 128.7mm

Operation System Delta Real Time OS
MCU 32-bit RISC Micro-controller
Flash ROM 128 MB
NOR Flash ROM
(OS System: 30MB / Backup: 16MB / User Application: 82MB)
SDRAM 64Mbytes
Backup Memory 16Mbytes
Sound Buzzer Multi-Tone FrequencyƋ2K ~ 4K Hzƌƒ85dB
Effect
Output AUX N/A Stereo output
IEEE 802.3, IEEE 802.3u
10/100 Mbps
Ethernet Interface N/A auto-sensing
(has built-in isolated power circuit (Note
3)
ƌ
USB 1 USB Host (Note 2) Ver 1.1 / 1 USB Slave Ver 2.0
Memory Card SD Card (supports SDHC)

COM1 RS-232 (supports hardware flow control)

RS-232 / RS-422 / RS-485

Serial (Note
COM2 RS-232ƒRS-422ƒRS-485 (has built-in isolated power circuit
COM 3)
)
Port
RS-232 / RS-422 / RS-485
(Note
COM3 RS-232ƒRS-422ƒRS-485 (has built-in isolated power circuit
3)
)
Function Key N/A
Perpetual
Built-in
Calendar (RTC)
Cooling Method Natural air circulation
Safety Approval CEƒUL (Note 4) ƒKCC (Note 4)
Waterproof
IP65ƒNEMA4
Degree
Operation Voltage DC +24V (-10% ~ +15%)
(Note 5)
(has built-in isolated power circuit (Note 3))
AC500V for 1 minute (between charging (DC24V terminal) and FG
Voltage Endurance
terminals)
Power
12W
Consumption (Note 5)
Backup Battery 3V lithium battery CR2032 x 1
Backup Battery It depends on the temperature used and the conditions of usage, about 3
Life years or more at 25oC.