Scribd
Upload
291 views2 pages

Fanuc 11T Configuration Document

This document summarizes the configuration of a Fanuc 11T CNC for use with a DNC system. It outlines the CNC parameter settings including ISO mode, foreground/background settings, device selection, communication settings, and remote command protocols. It also provides notes on changing CNC parameters, outputting and inputting programs, and the wiring diagram between the CNC and DNC system including pinouts and jumper settings for handshaking.

Uploaded by

Leonardus
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
291 views2 pages

Fanuc 11T Configuration Document

This document summarizes the configuration of a Fanuc 11T CNC for use with a DNC system. It outlines the CNC parameter settings including ISO mode, foreground/background settings, device selection, communication settings, and remote command protocols. It also provides notes on changing CNC parameters, outputting and inputting programs, and the wiring diagram between the CNC and DNC system including pinouts and jumper settings for handshaking.

Uploaded by

Leonardus
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

8/1/2021 Fanuc 11T configuration document

FactoryWiz

Fanuc 11T configuration document

CNC Configuration Sheet


11T

CNC Parameters:

Setting screen:

Punch code- 1=ISO


TV CHECK=0 OFF
Under Service page: 

0000 =  xxx01000 (ISO)


0020 = 1 (Input device Foreground)
0021 = 1 (Output device Foreground)

0022 = 1 (Input device Background)

0023 = 1 (Output device Background)

5001 to 1 (Device Select)


5002 to 2 (RS232 Device
Select)
5110 to 3 (Device type DC Codes
used)
5111 to 1 (1 stop bit) 

5112 to 10 (4800 baud)


 11=9600, 9=2400, 8=1200 7=600 6=300

FactoryWiz DNC Settings:


Basic Communication

1.01- Port Type: Standard

1.11- Baud: 4800

1.12- Data Bits: 7

1.13- ASCII Even

1.14- Stop Bits: 1

1.15- Handshake:
XON/XOFF

Sending Options
2.11- Leader: %<10>

2.12- Trailer: %

2.23- Skip lines


that contain: %
2.31- Automatic timeout: 7

Receiving Options

1: O
3.11- Program identifier
3.12- Program Identifier 2: :

3.21- Receive timeout: 3

3.31- Ignore data before


first end-of-block: True
3.32- Ignore data after last end-of-block: True

Remote Commands

4.02- Request for file command: GET-


4.03- Request for file command (drip feed): DNC-


4:11- Request to save command: PUT-

Additional Notes:

Changing CNC Parameters:

System (Param) screen:



to MDI mode on machine. 
To set parameters, move dial
Press SETTINGS key. Change PWE (#8000) to 1. The CNC
will alarm. 
Outputting CNC Programs:

To output a program, set the CNC to "edit" mode. Press the PROG key on the control
panel.  Use the right arrow (Page) key until PUNCH appears. Press PUNCH, then
1/2
8/1/2021
p g ( g ) yFanuc 11T configurationppdocument ,
Press THIS.

Inputting CNC Programs:


To input a program, set the CNC to "edit" mode. Press the PROG key on the control
panel. Use the right arrow(Page)keys until READ appears. Press READ, then press
ALL. 

Wiring Diagram:
Pinout includes RTS/CTS Handshaking


DB-9 com port Wire color DB-25 CNC Jumper?




(Disconnected) Shield 1


2 (Receive Data) Green 2 (Transmit Data)


3 (Transmit Data) Red 3 (Receive Data)


5 (Signal Ground) Black 7 (Signal Ground)


7 (RTS) Brown 5 (CTS)


8 (CTS) Blue 4 (RTS)




6 (DSR) JUMPER
8 (DCD)

20 (DTR)

Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA  95119
408.224.9167 | www.factorywiz.com

https://desk.zoho.com/portal/factorywiz/en/kb/articles/fanuc-11t-configuration-document

2/2

You might also like