AXE 4 DIGITAL(ONE-ALARM) & 6 DIGITAL TOTALIZER Counter (72x72mm) MCT726 series
FEATURES
Accept more type sensors(switch, encoder, proximity switch Totalizer counting mode can be modified (synchronize or
,…etc)finish length/flow control un-sychronnize)
Accept input rates up to 10KHz N,R,C alarm control mode
Readout range (0~9999),Totalize range(0~999999) 0.36” & 0.28”LED highlight display
Alarm output action times 0~99.9sec can be modified Man-machine interface, easy to operate
Power down saving EEPROM Saving, data safekeeping about 10 years
Decimal point can be modified Modified inside parameter, must have pass code
Input scaling multiplied 0.001 to 9.999 can be modified
Name of Parts
TV Totalize value display
OUT1 OUT2
PV Counter value display
SV Setting value display
AL
ENT SET
Function keys Function keys
TRST PRST
4 3 2 1
Perdigit setting keys
Connect Diagram
Contact input (PNP) CMOS input (12V OR 15V) Sensor input (PNP 12V)
IN IN IN
12V Inside jumper 12V Inside jumper Sensor 12V Inside jumper
1 2 3 4 1 2 3 4 1 2 3 4
OFF ON OFF OFF COM OFF ON OFF OFF
COM OFF ON ON OFF GND COM
Contact inpu (NPN) TTL input (5V) Sensor inpu (NPN 12V)
IN IN IN
12V Inside jumper 12V Inside jumper Sensor 12V Inside jumper
1 2 3 4 1 2 3 4 1 2 3 4
ON OFF ON OFF GND COM OFF ON OFF ON COM ON OFF OFF OFF
COM
Alarm output control description
N(MANUAL): When count value equal setting value the relay ON & continue count until reset by panel or connect terminal then relay
OFF & count value return to RST setting value
R(RETURN): When count value equal setting value the relay ON & continue count until relay action time out then relay OFF & count
value return to RST setting value
C(CONTINUE): When count value equal setting value the relay ON & count value return to RST setting value then continue
count & relay action time out the relay OFF
N/R/C control mode is one-alarm,N control mode is totalizer
MODE: SYN(one-alarm count and totalizer count is synchronize counting)
:NSYN(one-alarm count alarm once,totalize count on the increase)
Key Introduce Operation Manual
Key Function 1. In normal display, The key function is call out setting group
2. In parameter setting page, The key function is data Enter , and go to next page
PRST Key Function 1.The key function is one-alarm count value return zero and realy OFF
TRST Key Function 1The key function is totalizer count value return zero and realy Off
AL SET Key Function 1. In normal display, The key function is call out totalizer alarm value
Per digital & key 1.In normal display according to alarm indicate press per digit / setting per alarm value
Function 2.Into parameter setting page,If need modify data can press per digit / key Into setting
procedure,The parameter data will increment/decrement (key response about 0.2 sec)
Digital 1 & key In setting page press digit 1 & key return normal display,but if in setting
Function Page the modify data will lost
No Key in anything In setting group or setting page no key in anything about 2 minutes, return normal display
Step Parameter mark description Parameter mark Operation manual
1 Normal display Press /FUNC key into P.COD setting page
2 P.COD(Pass code input page) 1. Key in 4 digit pass code with & & key
Default=0 2. Press key, the pass code is right into setting group , otherwise
return normal display
MODE(Count Mode) 1.Decide the totalize count mode with 1 or key(SYN,NSYN)
3 Default=SYN 2. Press key enter data and into PV.DP setting page
PV.DP(PV Decimal Point) 1.Decide PV,PP decimal point with digit 1 & (0~3)
4 Default= 0 2. Press key enter data and into TV.DP setting page
5 TV.DP(TV Decimal Point) 1.Decide TV.DP decimal point with digit 1 & (0~3)
Default= 0 2. Press key enter data and into SCAL setting page
6 SCAL(Scale) 1.Decide display scale with per digit & key(0.001~9.999)
2. Press key enter data and into OP.MO setting page
Default = 1.000
7 OP.MO(Output Mode) 1.decide output mode with digit 1 & (N,R,C)
Default= N 2. Press key enter data and into ACT setting page
8 ACT.(Active Time) 1.Decode active time with digit 1~3 & key(0.1~99.9sec)
Default = 1.0 2. Press key enter data and into CODE setting page
9 CODE(Code) 1.Decide page code with per digit & key (0~9999)
Default = 0000 2. Press key enter data and into LOCK setting page
10 LOCK(Panel Lock) 1.Decode panel lock with digit 1 & key(NO,YES)
Default = NO 2.Press key return normal display
Step Parameter Mark Description Parameter Mark Operation Manual
1 Setting one-alarm alarm value 1.In normal display,decode one-alarm alarm value with per digit & key
Default = 0000 (0~9999)
,no key in any key 5 sec. Auto save data
2 Setting totalizer alarm value 1.Press AL/SE Tkey
Default=0000 2.Decide totalizer alarm value with per digit & key (0~9999)
,no key in any key 5 sec. Auto save data
