Scribd
Upload
2K views2 pages

Transmission Valve Body Assy (A245E/A246E) : Overhaul

This document provides instructions for overhauling the transmission valve body assembly for A245E/A246E automatic transmissions. The instructions include inspecting the plunger sleeve position, removing and installing the transmission 2-way and 3-way solenoid assemblies, and checking bolt lengths with torque specifications provided. Proper cleaning and prevention of burrs or dropped parts is advised during disassembly and reassembly.

Uploaded by

Gearauto Power
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views2 pages

Transmission Valve Body Assy (A245E/A246E) : Overhaul

This document provides instructions for overhauling the transmission valve body assembly for A245E/A246E automatic transmissions. The instructions include inspecting the plunger sleeve position, removing and installing the transmission 2-way and 3-way solenoid assemblies, and checking bolt lengths with torque specifications provided. Proper cleaning and prevention of burrs or dropped parts is advised during disassembly and reassembly.

Uploaded by

Gearauto Power
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

40−91

AUTOMATIC TRANSMISSION / TRANS − TRANSMISSION VALVE BODY ASSY (A245E/A246E)

TRANSMISSION VALVE BODY ASSY (A245E/A246E)


4003O−01

OVERHAUL
NOTICE:
S Disassembling and reassembling should be conducted on a clean vinyl sheet or mat, or alumi-
num tray.
S Make the valve slide through the valve hole by its own weight. Do not forcibly pull out the valve
using needle nose pliers. When having difficulty in removing it, slant and shake the valve body
or use a magnet hand.
S Do not place the disassembled parts directly on metal work bench or waste cloth.
S Do not use dropped parts.
S Make sure that no burr is identified before assembling.

1. INSPECT POSITION OF PLUNGER SLEEVE


(a) Check that the key for the plunger sleeve is set in the
proper position.
HINT:
Be certain to check this before disassembly because the line
pressure changes according to the set position of the plunger
sleeve.

D25356

Transmission 2way 2. REMOVE TRANSMISSION 2WAY NO.2 SOLENOID


No. 1 Solenoid Valve ASSY
Transmission 2way
Solenoid Assy No.3
(a) Remove the bolt, and transmission 2 way No. 2 solenoid
assy.
(b) Remove the O−ring.
3. REMOVE TRANSMISSION 2WAY NO.1 SOLENOID
ASSY

(a) Remove the transmission 2 awy No. 1 solenoid assy.


(b) Remove the O−ring.
4. REMOVE TRANSMISSION 3WAY SOLENOID ASSY
NO.3
Transmission 2way
No.2 Solenoid Valve (a) Remove the bolt, and transmission 2 way solenoid assy
No.3.
Line Pressure control
(b) Remove the O−ring.
Solenoid Assy
5. REMOVE LINE PRESSURE CONTROL SOLENOID
No. 2 Lock Plate
D25332 ASSY

(a) Remove the bolt, line pressure control solenoid assy and
solenoid lock plate.

A245E,A246E A/T REPAIR MANUAL (RM847E)


40−92
AUTOMATIC TRANSMISSION / TRANS − TRANSMISSION VALVE BODY ASSY (A245E/A246E)

6. INSTALL LINE PRESSURE CONTROL SOLENOID


A ASSY
B

(a) Install the line pressure control solenoid assy and sole-
noid lock plate with the bolt.
Torque: 6.5 N×m (66 kgf×cm, 57 in.×lbf)
HINT:
Each bolt length is indicated below
Bolt C: 12 mm (0.472 in.)
7. INSTALL TRANSMISSION 3WAY SOLENOID ASSY
NO.3

(a) Coat new O−ring with ATF and install then on the trans-
mission 2 way solenoid assy No. 3.
(b) Install the transmission 2 way solenoid assy No. 3 with
the bolt.
Torque: 11 N×m (112 kgf×cm, 98 in.×lbf)
C HINT:
D25332 Each bolt length is indicated below
Bolt B: 60 mm (2.362 in.)
8. INSTALL TRANSMISSION 2WAY NO.1 SOLENOID
ASSY

(a) Coat new O−ring with ATF and install then on the trans-
mission 2 way No. 1 solenoid assy.
(b) Install the transmission 2 way No. 1 solenoid assy.
9. INSTALL TRANSMISSION 2WAY NO.2 SOLENOID
ASSY

(a) Coat new O−ring with ATF and install then on the trans-
mission 2 way No. 2 solenoid assy.
(b) Install the transmission 2 way No. 2 solenoid assy with the
bolt.
Torque: 11 N×m (112 kgf×cm, 98 in.×lbf)
HINT:
Each bolt length is indicated below
Bolt A: 25 mm (0.984 in.)

A245E,A246E A/T REPAIR MANUAL (RM847E)

You might also like