Products & Solutions / Product Index
HDX6803+D
Auto-Sensing 3G/HD/SD Demultiplexer With Up To 8 AES Outputs
The HDX6803+D 3G/HD/SD de-embedder module for the 6800+ frame has up to eight AES outputs
and a video processing amplifier. It allows control over the video while functioning as a de-embedded
audio processor for hot-switching de-embedded audio. This new module provides full audio delay,
audio processing and ability to de-embed metadata to external sources. The HDX6803+D is ideal for
any broadcast operation where the de-embedding of audio from HD or SD video signals is required or
where SD or HD video and (embedded and/or discrete) audio signals are processed.
The OP+HDX+R+D version includes the fiber sub-module that will allow the addition of an optical
receiver to complement the electrical inputs.
FEATURES
The HDX6803+has the following input and output ports:
• Inputs:
◦ One Video Serial digital input
◦ Genlock Input (Composite or Tri-Level Sync) frame or card user selectable
◦ DARS Input (unbalanced, balanced compatible with external baluns)
◦ Fiber Receiver (OP+HDX+R+D version)
• Outputs:
◦ Four serial video digital outputs
◦ Eight AES Outputs (unbalanced, balanced compatible with external baluns)
4 AES standard - 8 with HDX68OPT-AES8 license option
◦ RS232/422 serial port Metadata output
• Operates video standards: 525 and 625 (SMPTE 259M) ; 1080i/p; 720p (SMPTE 274M/296M);
3G (SMPTE 424M ) upgradeable
• Auto-detect or user-forced input video standard
• 10-bit video processing
• Digital equalization (supports Belden 8281/1694A and newer, thin coax cables like Alcatel
SD02)
• Passes all HANC samples
• Passes VANC with user-selectable option for VBI/ANC Line by Line Video Deleting
• Up to 8 frames of HD and 50 frames of SD video delay
• Loss of video modes:
◦ Pass
◦ Black
◦ Freeze
• Video processing amplifier with controls for:
◦ luminance gain
◦ luminance offset
◦ chrominance gain
◦ chrominance offset
◦ white clip
◦ black clip
◦ hue adjustment
• Ability to de-embed metadata
• Dolby header adjustment
• Seamless Sound ( On LOV audio de-embedding from black or grey can be obtained)
• Support for fiber receiver (OP+ HDX+R versions) option via sub module on main module
• Basic audio limiting capability:
◦ User-selectable threshold for soft compression limiting
◦ Adjustable compression slope
◦ Adjustable attack time/rate
◦ Adjustable delay time/rate
◦ Noise gate level and time
• Video and audio test generator
• AES audio routing/advanced processing
• Internal audio processing amplifier with gain, swap, invert, delay, mix (sum) of de-embedded
audio channels
• Bypass able sample rate conversion for external and embedded Audio
• Data mode for passing compressed audio APTX, Dolby -E, AC-3
• 16-, 20- or 24-bit audio processing
• C, U & V bit transparency
• Shadowed/restored parameter settings when switching video standards
• Card edge control
• Ethernet remote control and monitoring
PRODUCT DETAILS
Each HDX6803+D package includes a module-specific breakout cable that expands the number of
available connections beyond what would fit on a standard two-slot back connector. The breakout
cable includes an RS-232/422 serial connector to embed or de-embed Dolby metadata. HDX6803+D
can be controlled manually via card-edge controls with OSD video display or remotely using CCS
Navigator , HTTP Web server or third-party SNMP-based control applications. In addition, the module
is Q-SEE -compliant, allowing for direct thumbnail monitoring when installed in a FR6822+QXFE
frame with a QSE6800+HT or QSEE6800+HST module.
BLOCK DIAGRAM
BACK MODULE
SPECIFICATIONS Specifications and designs are subject to change without notice
Serial Video Input
Number 1
Standards 1080p (SMPTE 424M) - 3G HD
1080i/p (SMPTE 274M); 720p(SMPTE 296M) – HD-SDI
SMPTE 259M-C, 270 Mb/s, 525/625 component – SD-SDI
Connector BNC per IEC 169-8
Impedance 75 ohms
Frame Rate 1080i/p: 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 Hz (3G rates are
future software upgradeable)
720p: 50,59.94,60 Hz
Return Loss >15 dB from 5 MHz to 1485 MHz; >12 dB from 1485 MHz to 2970
MHz
Equalization 3G-Adaptive cable equalization for up to 164 ft (50 m) (typical) of
Belden 1694A co-axial cable.
HD-Adaptive cable equalization for up to 492 ft (150 m) (typical) of
Belden 1694A co-axial cable.
SD- Adaptive cable equalization for up to 984 ft (300 m) (typical) of
Belden 8281 co-axial cable.
Serial Video Output
Number 4
Standards 1080p (SMPTE 424M) - 3G HD
1080i/p (SMPTE 274M); 720p(SMPTE 296M) – HD-SDI
SMPTE 259M-C, 270Mb/s, 525/625 component – SD-SDI
Frame Rate 1080i: 25, 29.97, 30, 59.94 Hz
1080p: 23.98 (p/psf), 24(p/psf), 25, 29.97, 30, 50, 59.94, 60 Hz (3G
rates are software upgradeable)
720p: 50,59.94,60 Hz 525,625
Connector BNC per IEC 169-8
Impedance 75 ohms
Return Loss >15 dB from 5 MHz to 1485 MHz; >12 dB from 1485 MHz to 2970
MHz
D.C. Offset 0.0 V 0.5 V
Signal Level 800 mV 10%
Rise and Fall Time <135 ps - 3G
<270 ps - HD-SDI
0.4 – 1.5nS - SD-SDI
Overshoot/Undershoot <10%
Jitter 3G: < 2UI pk-pk of timing jitter (>10Hz); <0.3UI pk-pk of alignment
jitter (>100kHz)
HD: < 1UI pk-pk of timing jitter (>10Hz); <0.2UI pk-pk of alignment
jitter for (>100kHz)
SD: <0.2UI pk-pk (>10Hz);
Delay Up to 8 frames less 2 lines for 3G/HD; 50 frames for SD
Reference Video
Level 1V pk-pk + 6dB/-3.5dB
Signal Type Analog composite 525/625 or tri-level sync (1080i/p /720p)
Connector BNC per IEC 169-8
Impedance 75 ohms
Return Loss >40 dB to 10 MHz (typical)
Unbalanced AES/DARS Input
Connector BNC (IEC169-8)
Impedance 75 ohms
Return Loss >25 dB, 0.1 to 6.0 MHz
Sensitivity <100mV
Input Audio Rate 32 kHz to 108 kHz
Balanced AES/DARS Input (with external baluns)
Connector XLR with external baluns
Sensitivity <200 mV
Impedance 110 ohms +/- 20% (0.1 to 6 MHz)
Maximum Input Signal 10 V (pk-pk)
Common Mode Rejection 0 V to 7 V (0 kHz to 20 kHz)
Input Audio Rate 32 kHz to 108 kHz
AES Unbalanced Output
Standard AES 3, SMPTE 276M
Type Unbalanced, AC coupled
Connector BNC (IEC169-8)
Impedance 75 ohms
Return Loss >25 dB, 0.1 to 6 MHz
>= 30 dB, 0.1 to 6 MHz
Signal Amplitude 1.0 V pk-pk 10% into 75 ohms load
Audio Rate 48 kHz
Rise/Fall Time 30 ns to 44 ns (10% to 90%)
Bits 24, 20 or 16
AES Balanced Output (with external baluns)
Type Balanced, transformer coupled
Connector XLR with external baluns
Impedance 110 ohms 20% (0.1 to 6 MHz)
Signal Amplitude 2 to 7 V pk-pk into 110 ohms load
Audio rate 48 kHz
Jitter 20 ns
Rise/Fall Time 5 ns to 30 ns (10% to 90%)
Bits 24, 20 or 16
Fiber Optic Input (Receiver)
Number of Inputs 1
Wavelength 1260 nm ~ 1620 nm
Connector SC/PC per IEC 61754-4-1
Overload Input Power 0 dBm PIN
Input Sensitivity -20 dBm PIN
RS-232/RS-422 (Metadata I/O)
Standard Electrical specification EIA-232C
Connector DB-9 232/422 switchable
Power Consumption
12 W maximum
Operating Temperature
41 to 113캟 (5 to 45캜)
Auto-Sensing 3G/HD/SD Multiplexer With Up To 8 AES Outputs
ORDERING INFORMATION
HDX6803+D Auto-Sensing HD/SD demultiplexer with four AES outputs, 3G-capable (with
appropriate software key), includes double-slot back module and breakout
cable, QSEE-compliant
HDX68OPT-AES8 Optional software key upgrade for HDX6803+ to provide eight discrete AES
outputs
HDX68OPT-3G Optional software key upgrade for HDX6803+ to provide 3 Gb/s HD capability
OP+HDX+R+D Auto-Sensing HD/SD demultiplexer with four AES outputs, 3G-capable (with
appropriate software key), includes double-slot back module and breakout
cable, QSEE-compliant with fiber optic receiver
6800+OPT+16CAPM Breakout cable with coax connectors for unbalanced AES I/O (NOTE: One cable
provided with each HDX6803+ or OP+HDX+R unit ordered)
NOTE: One unbalanced audio breakout cable (6800+OPT+16CAPM) is included with each
HDX6803+D module purchased and does not need to be separately ordered/purchased.
Additional/replacement cables can be ordered using part numbers 6800+OPT+16CAPM
Connector Options
OP+OPT+ST OPTO+ -ST connector option for OPTO+ fiber modules
OP+OPT+FC OPTO+ -FC connector option for OPTO+ fiber modules
