Right choice for ultimate yield

LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.

Human Machine Interface

XGT Panel
iXP Series User’s Manual

iXP70-TTA
iXP80-TTA
iXP90-TTA

 Read this manual carefully before

installing, wiring, operating, servicing
or inspecting this equipment.

 Keep this manual within easy reach

for quick reference.
http://www.lsis.com
 Safety Precautions

Before using the product…

To use the product safely and effectively, please read this instruction manual thoroughly before use.

► Please keep to the safety precaution, for it is to prevent accidents and potential danger from

occurring.

► Safety precaution is classified into ‘Warning’ and ‘Caution’ and their meanings are as follows.

Warning Violating the instruction may result in serious personal injury or death.

Caution Violating the instruction may result in slight personal injury or product

damage.

► The indicated illustrations on the product and in the manual have the following meanings.

Be cautious, for danger may be present.

Be cautious, for there is a possibility of an electric shock.

► After reading the instruction manual, keep it handy for quick reference.

1
 Safety Precautions

Design Precautions

Warning
Install a safety circuit external to the HMI to protect the whole control system in case of
external power supply trouble.
Serious trouble may occur to the entire system due to erroneous output/operation of the HMI.

Design Precautions
Caution
In/output signal or communication cable should be at least 100mm apart from
High-voltage/power wires.
Otherwise, it may cause erroneous output/operation.

Installation Precautions

Caution
 Use the HMI in an environment that meets the general specification contained in this

manual or datasheet.
Otherwise, it could result in electric shock, fire, erroneous operation or deterioration.

 In case of much vibration in the installed environment, be sure to insulate the HMI from

direct vibration.
Otherwise, it could result in electric shock, fire or erroneous operation.

 Be sure not to let foreign substances such as conductive debris inside the product.
Otherwise, it could result in electric shock, fire or erroneous operation.

2
 Safety Precautions

Wiring Precautions

Warning
 Be sure to turn off the HMI and external power before wiring.

Otherwise, it may result in an electric shock or damage to the product.

Caution
 Wire correctly by checking each of the product’s rated voltage and terminal layout.
Otherwise, it may result in fire, electric shock or erroneous operation.

 Tighten terminal screws with specified torque when wiring.

If terminal screws are loose, it may result in short circuits, fire or erroneous operation.

 Use the exclusive HMI 3-type grounding for the FG terminal.

If not grounded, it may result in erroneous operation.

 Be sure not to let any foreign substances such as wiring debris inside the module.
Such debris may cause fire, damage or erroneous operation.

3
 Safety Precautions

Startup and Maintenance Precautions

Warning
 Do not touch the terminals while power is on.
Otherwise, it may cause electric shock or erroneous operation.

 Turn off the HMI and external power when cleaning or tightening the terminal.
Otherwise, it may cause electric shock or erroneous operation.

 Do not charge, disassemble, heat, short circuit, solder, etc. the battery.
Mishandling the battery may cause overheating, crack, fire and may result in injury or fire.

Caution
 Do not disassemble PCB from the product case or modify the product.
Otherwise, it may result in fire, electric shock or erroneous operation.

 Use cellular phone or walky-talky at least 30cm away from the HMI.
Otherwise, it may result in erroneous operation.

Disposal Precaution
Caution
 When disposing of this product or battery, treat it as industrial waste.
Otherwise, it may cause poisonous pollution or explosion.

4
 Revision History

Revision History

Version Date Contents Revised location

V1.0 ‘11.11 First Edition -

※ The number of User’s manual is indicated the right side of the back cover.
ⓒ LSIS Co., Ltd 2013 All Rights Reserved.
Contents

Chapter. 1 General Introduction..................................................................................... 1-1~1-7

1.1 How to use the Instruction Manual .............................................................................................................................. 1-1

1.2 Feature .......................................................................................................................................................................... 1-3
1.3 Terminology................................................................................................................................................................... 1-7

Chapter. 2 System Configuration ..................................................................................... 2-1~2-8

2.1 Part Names ................................................................................................................................................................... 2-1

2.2 System Configuration ................................................................................................................................................... 2-4

Chapter. 3 Standard Specification ................................................................................. 3-1~3-5

3.1 General Standards........................................................................................................................................................ 3-1

3.2 Function Standards....................................................................................................................................................... 3-2

Chapter. 4 System Configuration .................................................................................4-1~4-11

4.1 Touch Calibration .......................................................................................................................................................... 4-2

4.2 Backlight Setting ........................................................................................................................................................... 4-3
4.2.1 PIR sensor.......................................................................................................................................................... 4-4
4.3 Date Time Setting ......................................................................................................................................................... 4-5
4.4 Ethernet Setting ............................................................................................................................................................ 4-6
4.5 Environment Setting ..................................................................................................................................................... 4-7
4.6 Sound Setting ............................................................................................................................................................... 4-8
4.7 XP-Remote Setting..................................................................................................................................................... 4-10
4.8 Buzzer Setting..............................................................................................................................................................4-11

Chapter. 5 Diagnostics .................................................................................................. 5-1~5-10

5.1 Screen Diagnosis ......................................................................................................................................................... 5-2

5.2 Touch Diagnosis ........................................................................................................................................................... 5-3
5.3 Backup Memory Diagnosis .......................................................................................................................................... 5-4
5.4 Flash Memory Diagnosis Function .............................................................................................................................. 5-5
5.5 CF Card Diagnosis ....................................................................................................................................................... 5-6
5.6 Serial Communication Diagnosis................................................................................................................................. 5-7
5.7 SD Card Diagnosis ....................................................................................................................................................... 5-9
5.8 USB Memory Diagnosis............................................................................................................................................. 5-10

8
 Contents

Chapter. 6 Viewing Information of PLC Connection Status ..................................... 6-1~6-8

6.1 PLC Communication Configuration Settings .............................................................................................................. 6-2

6.2 Connection Information ................................................................................................................................................ 6-3
6.3 PLC Information............................................................................................................................................................ 6-4
6.4 History of PLC Error .................................................................................................................................................... 6-4
6.5 History of PLC Mode Conversion .............................................................................................................................. 6-5
6.6 History of PLC Power ................................................................................................................................................. 6-5
6.7 History of PLC System ............................................................................................................................................... 6-6
6.8 N:1 Settings ................................................................................................................................................................. 6-7
6.9 Program Monitor ......................................................................................................................................................... 6-8

Chapter. 7 Storage Function........................................................................................... 7-1~7-7

7.1 General Introduction ................................................................................................................................................... 7-1

7.2 Downloading Project through the Storage Equipment ............................................................................................... 7-2
7.3 Uploading Project through the Storage Equipment .................................................................................................... 7-3
7.4 Updating the Device through Storage Equipment ...................................................................................................... 7-4
7.5 Select a USB Storage Device ...................................................................................................................................... 7-5
7.6 Select a USB Storage Device while Monitoring a Project .......................................................................................... 7-6

Chapter. 8 XGT Panel S/W Update......................................................................................... 8-1

8.1 General Introduction ................................................................................................................................................... 8-1

Chapter. 9 File Backup through External Storage Equipment .................................. 9-1~9-8

9.1 Path Structure in case of File Backup .......................................................................................................................... 9-1

9.2 Operation setting when there is no space for backup................................................................................................. 9-4
9.3 Structure of path of video file and video capture files .................................................................................................. 9-4
9.4 Monitoring Connection Status of External Storage Equipment .................................................................................. 9-6
9.5 Safety Removal Switch ................................................................................................................................................ 9-7

Chapter. 10 Installation and Wiring............................................................................ 10-1~10-8

10.1 Installation ................................................................................................................................................................. 10-1

10.1.1 Installation environment ................................................................................................................................. 10-1
10.1.2 Notice in handling........................................................................................................................................... 10-2
10.1.3 Notice in installing the panel .......................................................................................................................... 10-2

9
Contents

10.2 Wiring ........................................................................................................................................................................ 10-5

10.2.1 Power wiring................................................................................................................................................... 10-5
10.2.2 Ground wiring ................................................................................................................................................. 10-8

Chapter. 11 Maintenance .............................................................................................11-1~11-3

11.1 Maintenance...............................................................................................................................................................11-1
11.2 Daily Maintenance .....................................................................................................................................................11-1
11.3 Periodical Maintenance .............................................................................................................................................11-2

Chapter. 12 EMC Standard Certification ................................................................. 12-1~12-2

12.1 Requirement for EMC Standard Certification ........................................................................................................ 12-1

12.1.1 CE standard certification .............................................................................................................................. 12-1
12.1.2 MIC standard certification ............................................................................................................................ 12-2
12.2 Requirement for Low Voltage Command Suitability ............................................................................................... 12-2
12.2.1 Standard certification for XGT Panel ............................................................................................................. 12-2
12.2.2 Selection of XGT Panel ............................................................................................................................... 12-2

Appendix 1. Troubleshooting..................................................... Appendix1-1~Appendix1-20

1. Type of Problem ..............................................................................................................................................Appendix 1-1

2. Problem when Starting ...................................................................................................................................Appendix 1-1
3. Reaction Problem when Touching .................................................................................................................Appendix 1-2
4. Display Problem of Figure and Object ...........................................................................................................Appendix 1-3
5. Communication Problem................................................................................................................................Appendix 1-7
6. CF/SD/USB Removal of Memory Card.........................................................................................................Appendix 1-8
7. Error Message during Execution of Program ................................................................................................Appendix 1-9

Appendix 2. Dimension...............................................................Appendix 2-1~ Appendix 2-3

10
 Chapter 1. General Introduction

Chapter 1. General Introduction

1.1 How to use the Instruction Manual

This instruction manual provides information such as specification, how to use, etc. of the product needed to operate iXP series of
XGT Panel.

iXP series is characterized as follow;

Item symbol Contents Remarks

70 26cm (10.4”) -
(A)
80 31cm (12.1”) -
LCD Size
90 38cm (15”) -

B STN Mono Not available

(B)
LCD Type
T TFT Color -

(C)
T Touch -
Touch Type

A Advance -
(D)
iXP Type
M Multimedia Available later

AC AC 100-240V -
(E)
Power type
DC DC 12/24V -

1-1
 Chapter 1. General Introduction

The user manual’s configuration is as follows.

Sequence Category Contents

Chapter 1 General Introduction It describes this manual’s configuration, product’s feature and term.

Chapter 2 System Configuration It describes feature and system configuration of each XGT Panel.

Chapter 3 Standard Specification It describes XGT Panel’s general and function specification.

Chapter 4 System Configuration It describes XGT Panel’s system configuration.

Chapter 5 Diagnostics It describes XGT Panel’s self-diagnosis.

Viewing information of It describes the way on connection status information of PLC which is
Chapter 6
PLC Connection Status connected with XGT Panel.
Transmission of Project It describes the way to execute the project by using USB/CF/SD
Chapter 7
from USB Storage Device storage device.
Chapter 8 XGT Panel S/W Update It describes the way to update engine at XGT Panel.
Backup files by using It describes the way to backup recipe, logging and etc. files by using
Chapter 9
Storage Devices storage devices.
Chapter 10 Installation and Wiring It describes an installation, wiring and caution for reliability of PLC system.
It describes inspection category and method for long normal operation of PLC
Chapter 11 Maintenance
system.
Chapter 12 EMC Standard It describes system configuration for EMC standard.

Appendix 1 Troubleshooting It describes a variety of error contents and measure.

Appendix 2 Dimension It describes the dimension of XGT Panel.

Warranty and
Appendix 3 -
Environment Policy

Remark
This manual doesn’t describe connection with XP-Builder and PLC. For their own function, Please refer to the related
manuals.

1-2
 Chapter 1. General Introduction

1.2 Feature

iXP series has the following features.

(1) Various types of external interface

(a) Supporting various storage media of USB, CF card, and SD card, it maximizes the customer’s usability.
Multimedia type provides interfaces of video input, audio input, video output, and audio output so as to add the functions
needed to exert high performance. Extended interface designed to stack maximum three layers allows mounting a variety
of communication cards on it. In addition, the right part of extended interface is designed so as to mount VM module that
allows inputting 4-channel video.

Extended connector
Video Input (Multimedia type)
- Communication module that can be stacked
up to 3 stories (To be added)
Audio Input (Multimedia type)
VM Module Connector
- 4 Channel Video Input (To be added) Video Output (Multimedia type)
- RGB Output

422/485 Terminating Resistance Option S/W

CF Card
- Data Backup (alarm, logging, recipe and etc.)
- Project Data Storage (image, upload project and
etc.)
SD Card
- Data Backup (alarm, logging, recipe, etc.)
- Project Data Storage (image, upload project and etc.)
CF/SD Safety Removal S/W

(b) Presence sensor is placed at the front upper side so as to control backlight power source as it detects the presence. This
enables the user to turn on/off backlight either by touch or as it detects a movement of human body or not, and thereby
contribute to energy saving. In addition, one each channel of USB Host and Device is placed at the front side so that the
user can access with ease. That is, USB device is provided in such a method of basic communication connection with PC
so that the user can easily download the project through XP-Builder. Furthermore USB HOST 1 Channel located at the
front side allows the user to insert and remove the storage media with ease.

1-3
 Chapter 1. General Introduction

PIR sensor
- Detects human movement

USB DEVICE
- Project download through XP-Builder

USB HOST
- Data backup (alarm, logging, recipe and etc.)
- Project data storage (image, upload project and etc.)
- Mouse, keyboard and printer

(c) Various communication connectors are placed at the lower side so that it can be connected in a variety of types with the
control device such as PLC, inverter, etc. With two channels of USB HOST attached, it provides total 3 USB Hosts
including one channel at front side. This enables the user to diversely connect USB-based peripheral device that uses
mouse, key board, printer, etc. as well as for the purpose of backup.
• Through RS-232C, RS-422/485, Ethernet (10Base-T /100Base-TX) communication, it can be connected with control
device.
USB HOST Ethernet

- Data Backup (Alarm, Logging, Recipe, etc.) - Project download through XP-Builder

- Project data storage (image, upload project, etc.) - Control device that can be communicated such as PLC

- Mouse, keyboard and printer - Connected with fieldbus and open network

Audio output
RS-232C RS-422/485
- Connected with external speaker
- Control device that can be communicated - Control device that can be communicated
such as PLC such as PLC

(2) Based on Windows CE

(a) Adoption of Microsoft Company’s Windows CE

• Windows CE 6.0

(b) Advantage
• It provides stable software capacity by using Microsoft Company’s platform.
• It can process diverse function simultaneously.
• It provides diverse interface including Ethernet, USB and CF/SD card.
• The user interface including mouse and keyboard can be connected.
• It has high flexibility like computer software.
• Fast reaction is available when adding new equipment.
• Wide data sharing and management with upper system is available. (Later)

1-4
 Chapter 1. General Introduction

(3) Improvement of project transmission time

(a) It provides Ethernet which is faster than RS-232C.

Download

Upload

(b) It provides the transmission function from USB storage device.

Data change

(4) High quality screen

(a) It provides the high quality screen and clearness by high quality LCD.
• It adopts TFT LCD which supports the 24-bit Color.

(b) It provides diverse graphic type.

• It is available to express precisely and actually.
• It provides the simple moving function with GIF support.

(5) Analog touch Panel

(a) It adopts analog (resistor film method) Touch Panel.

• Visibility is improved without the grids.

(b) It provides high touch resolution.

• It can control Touch Panel precisely.

1-5
 Chapter 1. General Introduction

(6) Multilingual and diverse font

(a) It supports the multilingual function.

• It transmits the Windows/User font used in computer to XGT Panel.
• Additional language development is not necessary.
• Multilingual language is an advantage of Windows CE.

(b) It can express four kinds of language simultaneously.

• It can express 8 kinds of language simultaneously.
• Language switching is available by using special switch during operation.

(c) It can provide the various fonts.

• Various expressions are available by using the Windows/User font.
• Font size and type can be adjusted freely.

(7) Advanced function

(a) Alarm function

• The History alarm can be classified alarm group and alarm list and selected alarm can be expressed by alarm search.
• The Flow alarm indicates current or the latest alarm at the bottom of screen.
• The System alarm indicates the important problems from operation.
• It provides 256Kbyte areas for backup.

(b) Logging function

• It provides conditional logging according to device condition and continuous periodic logging which operates periodically
according to time and device status.
• It provides 512Kbyte areas for backup.
• Backup into CF/SD card or USB storage device is available.
• Backup data’s type is stored in Excel, it is easy to use.

(c) Recipe function

• It provides READ/WRITE function.
• It provides 128Kbyte areas for backups. [General recipe: 255 (255 blocks and set up to 10,000 double word for each
one of them), File recipe: 5000]
• Backup into the CF/SD card or USB storage device is available.
• Backup data’s type is stored in Excel, it is easy to use.

(d) Scheduler function

• It can be set up to Max. 32.

(e) Print function

• It provides a Screen/Alarm print function.
• It can be printed by USB printer.

(f) Script function

• It provides more flexible function by user Script.
• It can be diversely applied to such as including Global/Object/Screen indication and so on.

(g) Providing sound output function

• It basically provides audio output function in all the types.
• It allows connecting with amp built-in external speaker. With the sound function set, it enables to output a variety of
WAV files.

1-6
 Chapter 1. General Introduction

(h) Providing video input function (Multimedia type only)

• Analog camera allowing input of signals such as NTSC, PAL, SECAM, etc. can be connected using coaxial cable.
• It provides preview function that allows watching video input data, and record/play functions as well.
• It provides the function that stores video input data for maximum 120 seconds and then play it using a specific trigger.
(i) Providing sound input function. (Multimedia type only)
• Sound source can be input through MIC/Line-IN, which can be selected by S/W.
• Sound input data is stored together when recording the video.
• It provides an optional function of outputting the sound input data to the speaker.
(j) Providing video output function. (Multimedia type only)
• It provides the function of outputting HMI screen to PC in HMI resolution by connecting it to the PC using RGB cable.

(8) Stable product suitable for international standards

(a) CE, KC standard acquisition
(b) UL(cUL) standard acquisition

1.3 Terminology

It describes terms used in this manual.

Term Definition Remarks

Ex.) CPU module

A standard element that has a specified function which configures the system.
Module Power module,
Devices such as I/O board, which inserted onto the mother board or base unit.
I/O module

A single module or group of modules that perform an independent Ex.) Basic unit,
Unit
operation as a part of PLC system. Extension unit

System consisted of PLC and peripheral device which can be controlled by

PLC system -
user program.

XP-Builder Software used to write and edit the project. -

It is the software for edition, download, monitoring to realize data

XP-Manager communication between XGT Panels through XP Link with online control
function.

XP-Remote Software used to remote monitor and control the XGT Panel

Cnet module Computer Link -

FEnet module Fast Ethernet Network -

Abbreviation of ‘Real Time Clock’. It is used to call general IC that contains

RTC -
clock function.

1-7
 Chapter 2 System Configuration

Chapter 2 System Configuration

Characteristic of each iXP series and its system configuration are as follow;

2.1 Part Names

2.1.1. iXP70 (80/90)-TTA /AC (DC)

○
1

○
2

○
6
○
3

○
4

○
5

○
18

○
17

○
16

○
15

○
14

○
13

○
7 ○
8 ○
9 ○
10 ○
11 ○
12

○
19 ○
20 ○
21 ○
22 ○
23 ○
24

2-1
 Chapter 2 System Configuration

No Name Description

○
1 PIR sensor Sensor that detects human movement
1) Analog Touch Panel: Input by user’s touch
○
2 Front Part
2) LCD: Screen indication
○
3 Power status LED Indicating the state of device (On: Green)
1) Logging/Recipe/Screen Data Backup
○
4 USB Device 2) Send project data and XP-Run time
3) Receive back data and project file
Composed of three ports (Front side 1 port, Lower end 2 ports)
○
5 1) USB Memory Connection: Backup of data such as alarm/logging/recipe
and storage of screen data
USB Interface
2) USB Memory Connection: Send/Receive project data, Send XP-Runtime
○
23 3) User’s Interface Connection: Using mouse/keyboard
4) Printer connection: Printing function

○
6 Panel Mounting Part Fixing XGT Panel on the panel using bracket

○
7 Power Terminal Cover Prevention from electric shock

○
8 VM Module 4 channels Video Input  Optional board to be developed later

○
9 Reset Switch Hardware Reset Switch
RS-422/485 Terminating RS-422/485 Terminating Resistance On/Off  See Communication Instruction
○
10
Resistance Switch Manual 2.5.1 Switch
Communication, I/O Option Module 3 Units Mounted  Optional board to
○
11 Extended Interface
be developed later
○
12 CF HOT SWAP Switch CF Card Safety Removal Switch

○
13 SD HOT SWAP switch SD Card Safety Removal Switch
1) Backup of data such as alarm/logging/recipe and storage of screen
○
14 CF Card Interface data
2) Send/Receive project data, Send XP-Runtime
1) Backup of data such as alarm/logging/recipe and storage of screen
data
○
15 SD Card Interface
2) Send/Receive project data, Send XP-Runtime
3) Window CE OS Update Function (Can be used with DIP S/W set)
○
16 Video Output 1 channel Video Output(RGB Output)  Multimedia type only

○
17 Audio Input 1 channel Audio Input(MIC/LINE-IN) Multimedia type only
1 channel Video Input (NTSC/PAL/SECAM supported)
○
18 Video Input
 Multimedia type only
○
19 Audio Output 1 channel Audio Output

○
20 RS-422/485 Connector RS-422/485: PLC or Control Device Communication

○
21 RS-232C Connector RS-232C: PLC or Control Device Communication

2-2
 Chapter 2 System Configuration

No Name Description
Ethernet: 10Base-T / 100Base-TX
1) Send Project Data
○
22 Ethernet Terminal 2) Receive backup data and project file
3) Send XP-Runtime
4) PLC/Control Device Communication
○
24 Power Terminal Composed of Power Input and FG Terminal

Note
(1) For further details on connection of communication, please refer to Communication Instruction Manual.
(2) For further details on installation, please refer to the Chapter 10.

When you unpack the produce box to use XGT Panel, you can find prevention switch mounting on the device setting switch
that prevents battery discharge. Device setting switch consists of 6 switches. Of them, 3rd switch has battery discharge
preventing function. With this prevention switch upward to A, it starts operating backup function.

No.3 Switch (BACK UP BATTERY On) to be

located toward A
Device setting switch is made up of followings;

Pin
Configuration Function
Number
No.1 Reserved
A Config. NAND FLASH is used for booting (default)
No.2
B Config. NAND FLASH is not used for booting
A Config. BACK UP BATTERY On
No.3
B Config. BACK UP BATTERY Off (default)
A Config. Watchdog function On (default)
No.4
B Config. Watchdog function Off
A Config. SD Card is used for booting
No.5
B Config. SD Card is not used for booting (default)
A Config. USB, UART is used for booting
No.6
B Config. USB, UART is not used for booting (default)

2-3
 Chapter 2 System Configuration

Be sure not to flip switches Nos. 2, 5, and 6 toward A at the same time. Normally it is recommended to set switch No.2 toward A.
If you boot it with switches Nos. 2, 5, and 6 to A at the same time, it may cause malfunction of booting sequence resulting in
white screen and abnormal booting.

2.2 System Configuration

(1) PC and its Construction

In order to use XGT Panel, it is necessary for XP-Builder to prepare project data and transmit it to XGT Panel.
Normally you can connect with XGT Panel using USB 2.0 Device. Maximum Communication speed is 480Mbps.
iXP Series PC

USB Cable

USB Device USB Host 2.0

With Ethernet in use, you can transfer project data more quickly.
With LAN environment built in the following configuration, you may use it more easily and effectively.

iXP Series PC

Ethernet hub

1:1 connection will be supported just in case LAN environment is not built. (However, LAN cable made of cross cable is required.)

PC
iXP Series

Ethernet Cable (direct connection)

10Base-T/100Base-TX 10Base-T/100Base-TX

2-4
 Chapter 2 System Configuration

If it is impossible to transfer project data using Communication, you can use USB storage device, SD memory Card, and CF
memory Card. For how to use in details, please see the Chapter 7 and XP-Builder User’s Manual.

PC
iXP Series

Used for saving update file and

Used for update and backup
backup data

USB memory SD card CF card USB memory SD card CF card

(2) PLC and its Construction

With RS-232C cable in use, you can connect it up to 15m in a direction 1:1 connection.

iXP Series PLC

RS-232C cable (Max. 15m)

RS-232C RS-232C

With RS-232C to RS-422/485 Converter in use, you can connect it in extended length. But, it doesn’t support 1: N connection.

iXP Series PLC

RS-422/485 cable (Max. 500m)

RS-232C RS-232C
RS-232C to RS-232C to
RS-422/485 converter RS-422/485 converter
Converter Converter

2-5
 Chapter 2 System Configuration

With RS-232C wireless converter in use, it enables communication between XGT Panel and control device

iXP Series
PLC

RS-232C RS-232C
RS-232C RS-232C
Wireless
Wirelessconverter
converter Wireless
Wirelessconverter
converter

With RS-422/485 cable in use, it enables connections such as 1:1, 1: N, N: 1 and N: M up to 500m.

iXP Series PLC

RS-422/485 cable (Max. 500m)

RS-422/485 RS-422/485

iXP Series PLC

RS-422/485

RS-422/485 cable (Max. 500m)

RS-422/485

2-6
 Chapter 2 System Configuration

With N: 1 and N: M in connection, it enables connection in a RS-485 method.

iXP Series PLC

RS-485

RS-485 cable (Max. 500m)

RS-485

iXP Series PLC

RS-485
RS-485 cable (Max. 500m) RS-485

It enables communication configuration using LAN through Ethernet switch hub and communication configuration using a
direct cable.

PLC
iXP Series

Ethernet hub

iXP Series PLC

Ethernet direct cable

10Base-T/100Base-TX 10Base-T/100Base-TX

2-7
 Chapter 2 System Configuration

With LAN in use, it enables to connect multiple numbers of XGT Panels with the control device. It also enables remote control
from PC and operation through a data server.
iXP Series PLC

PC iXP Series
Ethernet hub

(3) Multimedia function

Through Video Input/Output, Audio Input/Output functions, it provides multimedia functions such as remote monitoring, screen
data indication, sound effects, etc (But, the function except Audio Output can be supported by multimedia-type only)

CCD Camera
Video Input*
iXP Series

Mike
Audio Input*

Speaker

Audio Output

Monitor
Video Output*

*Support only for Multimedia type

Note
(1) For how to make Ethernet cable, please see the Communication User’s Manual.
(2) For how to transfer project, please see XP-Builder User’s Manual.

2-8
 Chapter 3. Standard Specification

Chapter 3. Standard Specification

3.1 General Standards

iXP Series general standard is as follows.

No. Category Standard Related standard
Ambient
1 operating 0℃∼+50℃ -
temperature
Storage
2 -20℃∼+60℃ -
temperature
Operating
3 10∼85%RH, non-condensing. -
humidity
Storage
4 10∼85%RH, non-condensing. -
humidity
Occasional vibration count -

Frequency Acceleration Amplitude

5 ≤ f < 9㎐ - 3.5 mm
Vibration 9 ≤ f ≤ 150㎐ 9.8㎨ - 10 times each
5
resistance in X, Y and Z
Continuous vibration IEC 61131-2
direction
Frequency Acceleration Amplitude
5 ≤ f < 9㎐ - 1.75 mm
9 ≤ f ≤ 150㎐ 4.9㎨ -
* Maximum shock acceleration: 147㎨ (15G)
Shock
6 * Duration time: 11㎳ IEC 61131-2
endurance
* Pulse wave: half sine pulse (3 times each in X, Y and Z directions)
Square wave AC: ±1,500V
LSIS Standard
Impulse noise DC: ±1,000V

Electrostatic ±6 kV (Discharge by contact) IEC 61131-2

discharge Immunity ±8kV (Air discharge) IEC 61000-4-2
Noise Radiated IEC 61131-2
7 80 ~ 1000 MHz, 10 V/m
Immunity electromagnetic
IEC 61000-4-3
field noise
Communication
Category Power module
Fast transient & interface IEC 61131-2
Burst noise IEC 61000-4-4
Voltage 2 kV 1 kV

8 Environment Free from corrosive gases and excessive dust -

Operating
9 Up to 2,000m (6,562 ft) -
height
10 Pollution degree 2 or less -
11 Cooling method Self-cooling -

3-1
 Chapter 3. Standard Specification

Remark
(1) IEC(International Electro technical Commission)
: International private group facilitating international cooperation of electric/electronic standardization, issuing international
standards and operating the compliance evaluation systems.
(2) Pollution degree
: As an index representing the pollution degree of an environment to determine the insulation of a device, pollution degree 2
generally means the status generating non-conductive contamination. However, it also contains the status generating
temporarily conduction due to condensation.

3.2 Function Standards

iXP Series function standard is as follows.

(1) DC type
Item iXP70-TTA/DC iXP80-TTA/DC iXP90-TTA/DC

Display type TFT LCD

Screen size 26.4cm (10.4”) 30.7cm (12.1”) 38.1cm (15”)

Display Resolution 800 x 600 pixel (SVGA) 800 x 600 pixel (SVGA) 1,024 x 768 pixel (XGA)

Color indication 16-bit and 24-bit Color (default: 16-bit Color)

Left/Right: 80 deg. Left/Right: 80 deg. Left/Right: 80 deg.
Indication degree Upper: 60 deg. Upper: 60 deg. Upper: 60 deg.
Lower: 80 deg. Lower: 80 deg. Lower: 80 deg.
Backlight LED Type

Backlight duration 60,000 hours

Brightness 700cd/㎡ 550cd/㎡ 800cd/㎡

Touch panel 4 – Line type, analog
Sound Output Magnetic buzzer (85dB)
Audio Output 1 channel, stereo audio output
Process ARM Cortex-A8 Core (32bit RISC), 1GHz
Flash 1GB(display 128MB)
Memory

Operating RAM 512MB

Backup RAM 1MB
Backup data Date/Hour data, Logging/Alarm/Recipe data and nonvolatile device
Battery duration Approx. 3 years (Operating ambient temperature of 25℃)
Ethernet 1 channel, IEEE802.1a, 10Base-T/100Base-TX
3 channels, USB 2.0 host (mouse, keyboard, printer and USB memory driver is available)
USB Host
1 channel, USB 2.0 slave (for download and upload project file)
RS-232C 1 channel

3-2
 Chapter 3. Standard Specification

Item iXP70-TTA/DC iXP80-TTA/DC iXP90-TTA/DC

RS-422/485 1 channel,RS-422/485 mode
CF Card 1 Slot (Compact Flash)
SD Card 1 Slot (SDHC)
Detection range: side 1-1.5m, front 40-50cm
Human sensor
Angle: high/low 100°, left/right 140° (detecting 5-20 micron infrared light)
Audio output LINE-OUT 1 channel
Audio input 1 channel audio input (MIC/LINE-IN)  support only for multimedia type
Video output 1 channel video output (RGB output)  support only for multimedia type
Video input 1 channel video input (NTSC/PAL/SECAM)  support only for multimedia type
Expansion module For communication and I/O option module (available later)
VM module 4 channels video input (available later)
Multi-language Up to 8 language simultaneously
Animation GIF format is available
Recipe available
Data logging available
Script executor available
Certifications CE, UL(cUL), KC
Protection standard IP65
Dimension (mm) 270.5 x 212.5 x 60.0 313.0 x 239.0 x 56.0 395.0 x 294.0 x 60.0
Panel cut (mm) 259.0 x 201.0 301.5 x 227.5 383.5 x 282.5
Rated voltage DC12/24V

Power consumption (W) 42 42 42

Weight(Kg) 2.2 2.4 3.9

(2) AC type
Item iXP70-TTA/AC iXP80-TTA/AC iXP90-TTA/AC

Display type TFT LCD

Screen size 26.4cm (10.4”) 30.7 ㎝(12.1”) 38.1㎝(15”)

Display Resolution 800 x 600 pixel (SVGA) 800 x 600 pixel (SVGA) 1,024 x 768 pixel (XGA)
Color indication 16-bit and 24-bit Color (default: 16-bit Color)
Left/Right: 80 deg. Left/Right: 80 deg. Left/Right: 80 deg.
Indication degree Upper: 60 deg. Upper: 60 deg. Upper: 60 deg.
Lower: 80 deg. Lower: 80 deg. Lower: 80 deg.
Backlight LED Type (replaceable)

Backlight duration 60,000 hours

Brightness 700cd/㎡ 550cd/㎡ 800cd/㎡

3-3
 Chapter 3. Standard Specification

Item iXP70-TTA/AC iXP80-TTA/AC iXP90-TTA/AC

Touch panel 4 – Line type, analog
Sound Output Magnetic buzzer (85dB)
Audio Output 1 channel, stereo audio output
Process ARM Cortex-A8 Core (32bit RISC), 1GHz
Flash 1GB(display 128MB)
Memory

Operating RAM 512MB

Backup RAM 1MB
Backup data Date/Hour data, Logging/Alarm/Recipe data and nonvolatile device
Battery duration Approx. 3 years (Operating ambient temperature of 25℃)
Ethernet 1 channel, IEEE802.1a, 10Base-T/100Base-TX
3 channels, USB 2.0 host (mouse, keyboard, printer and USB memory driver is available)
USB Host
1 channel, USB 2.0 slave (for download and upload project file)
RS-232C 1 channel
RS-422/485 1 channel,RS-422/485 mode
CF Card 1 Slot (Compact Flash)
SD Card 1 Slot (SDHC)
Detection range: side 1-1.5m, front 40-50cm
Human sensor
Angle: high/low 100°, left/right 140° (detecting 5-20 micron infrared light)
Audio output LINE-OUT 1 channel
Audio input 1 channel audio input (MIC/LINE-IN)  support only for multimedia type
Video output 1 channel video output (RGB output)  support only for multimedia type
Video input 1 channel video input (NTSC/PAL/SECAM)  support only for multimedia type
Expansion module For communication and I/O option module (available later)
VM module 4 channels video input (available later)
Multi-language Up to 8 language simultaneously
Animation GIF format is available
Recipe available
Data logging available
Script executor available
Certifications CE, UL(cUL), KC
Protection standard IP65
Dimension (mm) 270.5 x 212.5 x 60.0 313.0 x 239.0 x 56.0 395.0 x 294.0 x 60.0
Panel cut (mm) 259.0 x 201.0 301.5 x 227.5 383.5 x 282.5
Rated voltage AC 100-240V

Power consumption (W) 42 42 42

Weight(Kg) 2.2 2.4 3.9

3-4
 Chapter 3. Standard Specification

Note

(1) Caution in power connection

: With AC power applied to DC power device, it may cause product damage or fire.
Please pay a special attention to connection.
(2) FG Connection
: For the device FG, please use ⑤ FG terminal in the Chapter 2.1, which is FG terminal for extended FG card.
(3) Battery discharge-preventing tape and DIP switch
: Tape is attached to prevent battery discharge. To use backup function, please remove the tape and turn on
DIP switch No. 3.
(4) Battery Operation and Life
: Battery is used for backup data maintenance and RTC (date/time) when the power of device is off. It is used only
when power is Off. Battery is not consumed with power applied. If battery is discharged, Super-Cap is used for
8 days for backup data maintenance and RTC (date/time) with power off
(5) LCD Backlight Replacement
: Please replace LCD if you want to replace LCD backlight.
(6) Caution in Audio Output
: Unamplified speaker without the volume adjustment function such as earphone, headset, etc. may make a small
sound output through LINE-OUT.

3-5
 Chapter 4. System Configuration

Chapter 4. System Configuration

It describes the system configuration including XGT Panel’s time setting, Ethernet connection setting, and connection with
PC and backlight.
If you press [Settings] button in XGT Panel’s basic screen, you can set XGT Panel’s environment as follows.

Main screen

System Configuration screen

4-1
 Chapter 4. System Configuration

4.1 Touch Calibration

When the location is not recognized in XGT Panel, Touch’s scale can be adjusted in XGT Panel. If you press [Touch Calibration]
button in System Configuration, the setting screen shows up. If you press five ‘+’ marks, XGT Panel’s touch location adjustment is
completed.

If you press two points simultaneously while [Allow Multi-touch] is selected, XGT Panel recognizes as if middle point between two points
is selected. If you press two points simultaneously while [Allow Multi-touch] is not selected, XGT Panel recognizes as if any point is not
selected.

Remark
(1) XGT Panel’s Touch Calibration setting is basically set. If Touch location is way off, adjusting menu with touch can be hard
through touch. In that case, You can select the Touch Calibration setting menu by USB mouse or simply touch
5 times at the empty space on the main screen.
(2) When touch location changes in using, redo touch setting.
(3) If you don’t allow Multi-touch, sensitivity is lower than when allowing Multi-touch.

4-2
 Chapter 4. System Configuration

4.2 Backlight Setting

If you press [Backlight Setting] button in [System Configuration] screen as follows, setting screen shows up.

[Dialog box explanation]

Name Explanation
Brightness It may adjust brightness of backlight.
Do not turn off backlight It doesn’t turn off backlight power.
Turn off backlight after idle time It automatically turns off backlight if not in touch for a certain period of time.
Turn off ~ minutes It turns off backlight after a designated time (unit of minute).
Set the sensitivity level for the PIR (Passive Infrared) sensor. The lower the
PIR sensor sensitivity value, the quicker the backlight will turn on. When set to the lowest value, the
backlight will turn on immediately when the screen is touched.

4-3
Chapter 4. System Configuration

4.2.1 PIR sensor

The XGT Panel’s backlight is activated by detecting movement around the XGT Panel. If you approach the XGT Panel
when the display is off, movement around the XGT Panel from the left, right or front, is detected and turns on the backlight.

(1) The XGT Panel has a detection range of 1-1.5m from both sides.

(2) The XGT Panel has a detection range of 40-50cm from the front.

Remark

The detection distance may vary depending on temperature and location.

4-4
 Chapter 4. System Configuration

4.3 Date Time Setting

If you press [DateTime Setting] button in [System Configuration] as follows, you can set XGT Panel’s data and time.

Remark
You can set data/time at device information of communication dialog at the XP-Builder.
For details, please refer to the XP-Builder’s manual.

4-5
Chapter 4. System Configuration

4.4 Ethernet Setting

If you press [Ethernet Setting] button in [System Configuration] screen as follows, you can change IP to use Ethernet.

You can change IP address by pressing [Set] button of each IP address, Subnet Mask and Gateway. By pressing OK button,
changed IP information is reserved.

Remark
We recommend the following method, when connecting with PC solely.

1) XGT Panel setting 2) PC setting

- IP Address : 192.168.0.10 - IP Address : 192.168.0.11
- Subnet Mask: 255.255.255.0 - Subnet Mask: 255.255.255.0
- Gateway : 192.168.0.1 - Gateway : 192.168.0.1

If you reboot after pressing [Disable] button, the device will not use Ethernet. In this case, booting speed gets faster.
If you use Ethernet again, reboot after pressing [Enable].

4-6
 Chapter 4. System Configuration

4.5 Environment Setting

If you press [Environment Setting] button in [System Configuration] screen as follows, you can set ‘Auto Goto Screen’ and ‘Buzzer
On/Off’.

Name Explanation
Auto Goto Screen When setting [Auto Goto Screen], XGT Panel is rebooted. Or when downloading the
edit data is completed, the screen automatically shows up. If you cancel this setting, the
user should press ‘Start’ button in order to move to the screen.
Quick Start When starting screen, screen shows promptly without showing progress bar because it
doesn’t caching the image in advance. However, if you select this option, first screen
shows slowly. Especially, if there are many animation objects in screen, it may take several
seconds based on image. But fast screen switching is available since second screen
switching.

4-7
Chapter 4. System Configuration

Hide Mouse Cursor Mouse cursor doesn’t show after screen switching
Buzzer On You can set whether you use buzzer through [Buzzer On/Off] button.
Disable Menu Bar The menu bar basically provided to go out from monitoring screen to the waiting screen
doesn’t show. In this case, if you want to go out to the waiting screen, you have to use
the special switch to close the monitoring screen.
Set Background Image If you select the image through [Set Background Image], background image of waiting
screen is set as the selected image. If you want to cancel, press [Delete Background
Image]

[Background Image Selection Screen]

[Use boot image] With an option selected, you cannot use it unless it is the image of
different resolution from that of XGT Panel or 32-bit image.
Clear Data All files downloaded by the user are deleted. If connection password is set, you have to
input the password. This password is connection password needed for project
download, etc. You can set that password in [Communication] 
[XGT Panel Information]  [Password] tap. The deleted files are user project file, web
server, VNC start module, option card driver, RAPIEnet communication setting data,
XP-manager setting data and etc. Setting through Environment Setting menu of device
is not initialized.
Buzzer Test It may test the buzzer.
Reset USB Power When XGT Panel starts, USB power state is converted from Off to On initializing the
connected device.
Enable Arabic Fonts It enables the language indicated from right to left directions.
Always Show Title Window It indicates title bar on pop up window. With title bar of pop up window selected, it may
move the location.
RS-232C 5V Power Supply When the monitor starts with XGT Panel button [Start] pushed, it outputs 5V power
using No. 9 pin of RS-232C Port. When turning off XGT Panel monitor and returning to
menu screen again, it stops power output.

Note
Buzzer can make settings in information on device tab of communication dialog box in the XP-Builder.
Please refer to the XP-Builder’s manual.

4-8
 Chapter 4. System Configuration

4.6 Sound Setting

It may adjust XGT Panel sound volume.

[Sound Setting Screen]

[Dialog box Explanation]

Name Explanation
Sound volume It may adjust sound output volume.
Input source It designates the sound input type in Line-in or microphone.
This function is supported in multimedia type XGT Panel only.
Line-in/MIC bypass to It transmits input sound (microphone, etc.) to the connected speaker.
speaker This function is supported in multimedia type XGT Panel only.

Note
In case of microphone with power not applied like ear microphone, it has no sound input function.
Unamplified speaker without volume adjustment function such as earphone, headset, etc. may make a small sound
output through LINE-OUT

4-9
 Chapter 4. System Configuration

4.7 XP-Remote Setting

Settings of XP-Remote that can remotely adjust XGT Panel can be changed.

[XP-Remote Setting Screen]

[Explanation of dialog box]
Name Explanation
Allow XP-Remote to connect It allows connecting remote XP-Remote.
Max. of XP-Remote connections It designates the maximum number of XP-Remote connected with XGT Panel.
Timeout value It stops communication when there is no request of communication from XP-Remote
within the designated time. In case XP-Remote is entitled to manipulation, it
withdraws the right to manipulation (10 seconds ~ 300 seconds)

Note
For the function of XP-Remote in detail, please refer to XP-Remote user’s manual.

4-10
 Chapter 4. System Configuration

4.8 Buzzer Setting

It may adjust volume and height of XGT Panel Buzzer.

[Buzzer Settings Screen]

[Explanation of dialog box]

Name Explanation
Buzzer On/Off It may turn on or off the buzzer that occurs when in touch mode
Buzzer volume It may adjust the volume of Buzzer
Buzzer tone It may adjust the height of Buzzer.

4-11
 Chapter 5. Diagnostics

Chapter 5. Diagnostics

It describes the diagnosis function for XGT Panel’s communication terminal, screen and touch function.
If you press [Diagnostics] button on the XGT Panel’s basic screen, the menu for diagnosis shows up.

Main Screen

Environment setting screen

5-1
 Chapter 5. Diagnostics

5.1 Screen Diagnosis

If you press [Screen] button, screens continuously change into diverse color with buzzer. For XP30-BTA/DC product, screen
changes into 8 steps’ light. After all screen for diagnosis pass. Then, Close button shows up with white ground.
If you press Close button, the initial screen shows up.

Diagnosis screen

Screen diagnosis

Display
RED > GREEN > BLUE > BLACK > WHITE>GRAPH
Sequence

5-2
 Chapter 5. Diagnostics

5.2 Touch Diagnosis

If you touch the screen, the touched location is displayed as follows. If pressing the [OK] button, you can quit the screen.

Touch diagnosis

If the touched location is not correct, reset the Touch setting. For detailed information, please refer to the
Chapter 4. System Configuration.

5-3
Chapter 5. Diagnostics

5.3 Backup Memory Diagnosis

If you press [Backup Memory] button, you can see the result of diagnosis in the result windows.

Completion of Backup Memory diagnosis

Remark
(1) If ‘NVRAM Data Access … Fail’ error is occurred, please contact with customer service center.
(2) If ‘BATTERY STATUS … BAD’ error is occurred, battery should be changed. Please contact with Customer service
center.

5-4
 Chapter 5. Diagnostics

5.4 Flash Memory Diagnosis Function

If you press [NOR Flash] button, you can see the result of diagnosis in the result widows.

Completion of Flash Memory diagnosis

Remark
If ‘Read Disk Information Error!’ occurs, please contact with Customer service center.

5-5
Chapter 5. Diagnostics

5.5 CF Card Diagnosis

If you press [CF Card] button, the result of diagnosis shows up in the result windows.

Completion of CF Card diagnosis

Remark

If ‘Read Disk Information Error!’ occurs, please contact with Customer service center.

5-6
 Chapter 5. Diagnostics

5.6 Serial Communication Diagnosis

If you press [Serial] button, you can diagnose Serial ports which is equipped at XGT Panel.
(In case of diagnosis purpose, you have to connect the loop-back terminal at each port.)

Serial port selection

Completion of serial port diagnosis

5-7
Chapter 5. Diagnostics

The RS-232C port terminal should be made as follows

(Connect the No.2 and 3 pin)

The RS-422/485 port terminal should be made as follows.

1 2 3 4 5 6

(Connect the TX+ with RX+ and TX- with RX-)

Pin Name Function

1 TX+ Transferring data
2 TX- Transferring data
3 RX+ Receiving data
4 RX- Receiving data
5 SG Signal Ground
6 FG Frame Ground

5-8
 Chapter 5. Diagnostics

5.7 SD Card Diagnosis

If you press [SD Card] button, the result of diagnosis shows up in the result windows.

Completion of SD Card diagnosis

Remark

If ‘Read Disk Information Error!’ occurs, please contact with Customer service center.

5-9
Chapter 5. Diagnostics

5.8 USB Memory Diagnosis

If you press [USB Memory] button, the result of diagnosis shows up in the result windows.

Completion of USB Memory diagnosis

Remark

If ‘Read Disk Information Error!’ occurs, please contact with Customer service center.

5-10
 Ch.6 Viewing Information of PLC Connection Status

Chapter 6 Viewing Information of PLC Connection Status

PLC Information, it shows XGT Panel configuration, PLC CPU status and various records.

Remark
You can check the status of PLC connection after project data is transmitted into XGT Panel.

6-1
Ch.6 Viewing Information of PLC Connection Status

6.1 PLC Communication Configuration Settings

You can select [Settings] button to change PLC communication settings

PLC Communication Configuration setting

Remark
- PLC Communication Configuration setting dialog box may look different.
- For further information about the settings, please refer to the PLC user manual.

6-2
 Ch.6 Viewing Information of PLC Connection Status

6.2 Connection Information

You can check the setting items for the connection with PLC such as vender of PLC, target device, connection type, ip address,
connection information and timeout value in the XP-Builder.

Remark

Connection No.  0 to 15 connections can be made.

6-3
Ch.6 Viewing Information of PLC Connection Status

6.3 PLC Information

You can check CPU type of PLC, operation mode, state, version, and scan time.

Remark
The following PLC is available for view of PLC information.
- MASTER-K CPU, FEnet, Cnet
- GLOFA-GM CPU, FEnet, Cnet
- XGK/XGB/XGI/XGR CPU, FEnet, Cnet

6.4 History of PLC Error

You can check the PLC Error History.

Remark
The following PLC is available for viewing Error History.
- MASTER-K CPU doesn’t have the Error History.
- GLOFA-GM CPU, FEnet, Cnet
- XGK/XGB/XGI/XGR CPU, FEnet, Cnet

6-4
 Ch.6 Viewing Information of PLC Connection Status

6.5 History of PLC Mode Conversion

You can check the history about our PLC’s RUN/STOP operation mode.

Remark
The following PLC is available for viewing PLC operation mode conversion history.
- MASTER-K CPU doesn’t have the history about operation mode conversion.
- GLOFA-GM CPU, FEnet, Cnet
- XGK/XGB/XGI/XGR CPU, FEnet, Cnet

6.6 History of PLC Power

You can check the history about when PLC was turned on and off

Remark
The following PLC is available for viewing the history of when our PLC was turned off and on.
- MASTER-K CPU doesn’t have the history about when our PLC was turned on and off.
- GLOFA-GM CPU, FEnet, Cnet
- XGK/XGB/XGI/XGR CPU, FEnet, Cnet

6-5
Ch.6 Viewing Information of PLC Connection Status

6.7 History of PLC System

You can check history about PLC system.

Remark
The following PLC is available for viewing history about system.
- MASTER-K CPU doesn’t have the history about system.
- Only GLOFA-GM CPU (GM4C) has the history about system. Other CPUs don’t have the history about system.
- XGK/XGB/XGI/XGR CPU, FEnet, Cnet

6-6
 Ch.6 Viewing Information of PLC Connection Status

6.8 N:1 Settings

Using N:1 communication, it means communicate number of XGT Panel with single PLC.

[N:1 settings dialog box]

Remark

For detail information about the N:1 communication, please refer to the XP-Builder manual.

6-7
Ch.6 Viewing Information of PLC Connection Status

6.9 Program Monitor

The programs that adopt LD language of XGK and XGB series can be monitored.

Remark
- Program Monitor driver can be downlaoded from XP-Manager
- Only support for XGK/XGB CPU, Cnet, Enet communication
- To enable the [Program Monitor] button, program monitor should be checked in which locates in the XP-Builder project
property menu.

6-8
 Chapter 7. Storage Function

Chapter 7 Storage Function

7.1 General Introduction

Downloading the user project made in XP-Builder from PC, uploading the project stored in the device to PC, updating the device
and etc are available through connection with XGT Panel with Serial cable or Ethernet cable generally. However, when those
connections are not available, you can use CF card, USB storage equipment

1. If you touch [Storage Function], the following dialog box shows.

2. In case of downloading the project by using CF card or USB storage equipment, touch [Project Download] button.
3. In case of transmitting the project data stored in the device to CF card or USB storage equipment, touch [Project Upload]
button.
4. In case of updating the XGT Panel with XGT Panel Software stored in CF card or USB Storage equipment, touch [XGT
Panel Update]

7-1
 Chapter.7 Storage Function

7.2 Downloading Project through the Storage Equipment

1. If you touch [Project Download], the following dialog shows.

2. Please select the targeted external memory in “Select Source”. Following path is indicated depending on the selected
external memory.
- USB: \USB Storage\XP_Project\
- CF: \Storage Card\XP_Project\
- SD: \SD Storage\XP_Project\
In case of downloading the project by using storage equipment, the project should be saved in the one lower directory
between those two directories.

3. Select one among directory lists and touch [OK].

4. Touch [OK] button, then download will start.

7-2
 Chapter 7. Storage Function

7.3 Uploading Project through the Storage Equipment

1. If you touch [Project Upload], the following dialog shows.

2. Please select the targeted external memory in “Select Source”. Following path is indicated depending on the selected
external memory
- USB: \USB Storage\XP_Backup\
- CF: \Storage Card\XP_ Backup\
- SD: \SD Storage\XP_ Backup\

3. If you touch [OK] button, project backup file is transmitted to the selected path.

4. The project backup file is saved when Download project backup file is selected when downloading the project.
If you don’t select, project backup file is not saved in the device and transmission to the storage equipment is not
available.

7-3
 Chapter.7 Storage Function

7.4 Updating the Device through Storage Equipment

1. If you touch [Project Upload], the following dialog shows.

2. Please select the targeted external memory in “Select Source”. Following path is indicated depending on the selected
external memory
- USB: \USB Storage\XP_Software\
- CF: \Storage Card\XP_ Software\
- SD: \SD Storage\XP_ Software\

In case of updating the device by using storage equipment, the XGT Panel Software project should be saved in the
one lower directory between those two directories.

3. If you touch [OK] button, the device is updated with XGT Panel Software in the designated path.

7-4
 Chapter 7. Storage Function

7.5 Select a USB Storage Device

1. When multiple USB devices are connected to the XGT Panel, you must select a device for
uploading, downloading, or backing up projects. You can change your selection at any point
during a project.

To select a USB storage device:

In the XGT Panel main menu, touch[Storage Function], then Touch [Select USB]

2. Select device from the list of connected devices

- Use: The selected device is indicated with an asterisk(*).

- Vendor Name: The device manufacturer
- Product Name: The device name
- Up/down: Move to the next or previous item
- Select: Save your selection
- Cancel: Exit without saving changes

7-5
 Chapter.7 Storage Function

7.6 Select USB Storage Device while Monitoring a Project

1. To select a storage device while monitoring a project, on the XGT Panel, touch [Start] to open the Select USB Storage
window. Select a USB device and touch [Select].

2. To select a storage device from the status bar, touch [USB].

3. If the selected device is disconnected or if another device is connected, the Select USB Storage window
appears again.

7-6
 Chapter 7. Storage Function

Remark

(1) Do not remove or turn off the selected USB device while running a project. Project data may be corrupted and cause the
project to malfunction.
(2) Do not erase or move the directory or folders on the USB device. Doing so may cause data to be corrupted or the project to
malfunction.
(3) When removing an SD or CF storage device, turn on the safe removal switch on the back of the panel and remove the
device only after the switch lamp turns off. Failure to do so may cause the device to be unrecognized when you
reconnect it.
(4) When you reconnect a device, allow at least three (3) seconds to establish the connection. Failure to do so may cause the
device to be unrecognized when you reconnect it.
(5) When one USB device is connected, turning on the power to the panel will set the USB device as the main storage device
automatically.
(6) When connecting multiple devices, the first device connected is set at the main storage device automatically. However,
removing devices does not change the selected storage device automatically. You must reselect the main storage device.

7-7
 Chapter 8. XGT Panel S/W Update

Chapter 8 XGT Panel S/W Update

8.1 General Introduction

It describes the function for updating the XGT Panel software.

Basically you can optimize XGT Panel when you download the project file in XP-Builder. Please use this function only
in case of updating XGT Panel specially.

New function is added to XGT software, you need to update a version of XGT Panel
Please refer to the following.

[Method]

Select [Upgrade -> Update XGT Panel] on the XGT Panel’s main screen. Then XGT Panel becomes update mode. In order
to return to the main screen, touch a screen for 3 seconds.

After downloading XGT Panel software from LSIS website, make a temporary folder and save it.

Designate the folder where the software will be saved in the XP-Builder’s [XGT Panel Update] windows and update XGT
Panel by [Send] menu. For more detailed information about XP-Builder, please refer to the XP-Builder user manual.

Remark
Do not remove communication cable or turn off the device during updating. It may cause the abnormal operation.

8-1
 Chapter 9. File Backup through External Storage Equipment

Chapter 9 File Backup through External Storage Equipment

Describes on management function about external storage equipment saving backup data of logging, recipe, and screen image
(1) XGT Panel can back up the logging, recipe, and screen image data at CF card or USB storage equipment according to setting
in XP-Builder.
(2) In case there is no space for backup in the designated storage equipment, it continues backup deleting previous data or stops
backup according to setting in XP-Builder
(3) Monitors attachment status of backup equipment at XP-Builder.

(4) In case the applicable storage device is not in use with safety removal switch of CF/SD card in operation, LED will be turned off
right away. If the applicable storage device is in use, however, LED will be turn off as its use is over. Data backup will be done
regularly only when LED is turned off and the device is removed.

9.1 Path Structure in case of File Backup

Backup path structure of logging, recipe, and screen image is as follows.

Root directory of CF or USB storage equipment

Logging

1 (Logging Number)

YYYY.MM.BeginDay.EndDay.0

DD.BeginHour.EndHour.0 (space for one folder is full)

DD.BeginHour.EndHour.1 (There is free space for one folder)

DD.BeginHour. FF (There is free space for one folder)

HH.BeginMinute.FF

Lhhmmss0.CSV

2 (same as lower structure 1)

Recipe

Rhhmmss0.CSV (same as lower structure of each logging number)

ScreenImage

Shhmmss0.BMP (same as lower structure of each logging number)

1. Path structure in case of logging backup

9-1
 Chapter 9. File Backup through External Storage Equipment

(1) Directory named ‘Logging’ is created under the root directory of USB/CF storage equipment
(2) The directory whose name is logging number is created under Logging directory.
(3) The directory whose name is year, month is created under Logging number directory.
(a) Includes day directory under
(b) Up to 500 day directories can be created.
(c) Name of year, month directory includes the firstly created day information under its directory

th
Ex) In case directory is created in 2010, October and includes directory since 15 under, directory’s name is
: 2010.10.15.FF
FF at end means the directory can save more data created in 2010, October (currently, the number of lower directory
is 500 or less)
(d) In case month is changed, changes directory name to day information of last created day directory.
th th
Ex) In case month becomes November from October and directory from 15 directory to 30 have been created in 2010,
October directory.
: 2010.10.15.30.0
(e) Though month is not changed, in case the number of day directory under year, month directory is 500 or above, directory
name is changed into name including day information of last created day directory.
th
Ex) In case the number of directory from first to 15 is 500 or above in the directory created in 2010, October.
: 2010.10.01.15.0
(f) In case there is the year, month directory having same start day and end day when changing directory’s name due to over
500 day directories or change of month, last digit index number increases.
Ex) In case there are three year, month directories that are having over 500 day directories created in October first and
2010 year October directory
: 2010.10.01.01.0
: 2010.10.01.01.1
: 2010.10.01.01.2
(4) Day directory is created under year, month directory
(a) Hour directory is created under day directory
(b) Day directory can have up to 500 hour directory
(c) Name of day directory includes not day information but also hour information of first created hour directory
(d) Relation between day directory and hour directory is same as relation between year month directory and day directory.
(5) Directory whose name includes hour information is created under day directory.
(a) Hour directory includes backup file under
(b) Hour directory can include up to 500 backup file
(c) Name of time directory include not only hour information but also minute information of first created file under
(d) Relation between hour directory and backup file is same as relation between year, month directory and day directory.
(6) Name of logging backup file includes the created hour, minute, second information.
(a) Backup file is created in CSV format.
(b) File name start with ‘L’ meaning logging and includes hour, minute, second, index information
(c) In case backup file is created at the same time in terms of second, index information at the end of file name increases.

2. Path structure in case of recipe backup

(1) Directory named ‘Recipe’ is created under USB/CF/SD storage equipment root directory.
(2) Year, month directory is created under Recipe directory
(3) The lower directory structure is same as that of logging backup path structure.
(4) Name of recipe backup file includes the created hour, minute, second information.
(a) Backup file is created in CSV format.
(b) File name start with ‘R’ indicating recipe and includes hour, minute, second, index information.

9-2
 Chapter 9. File Backup through External Storage Equipment

(c) In case backup file is created at the same time in terms of second, index information at the end of file name increases.

3. Path structure in case of screen backup

(1) Directory named ‘Screen Image’ is created under USB/CF storage equipment root directory.
(2) Directory whose name is year; month is created under Screen Image directory.
(3) The lower directory structure is same as that of logging.
(4) Name of screen image backup file includes hour, minute, second information.
(a) Backup file is created in bitmap format.
(b) File name starts with ‘S’ and includes hour, minute, second, index information.
(c) In case backup file is created at the same time in terms of second, index information at the end of file name increases.

4. Structure of path at memo backup

(1) ‘Memo’ directory will be formed at the sub route directory of USB/CF/SD storage device.
(2) Directory in the name of Year and Month will be formed below the Memo Directory.
(3) Structure of directory thereafter is same as that of logging backup route.
(4) Memo backup file has the name made of hour/minute/second when it was created.
(a) Backup file is created in the type of bitmap.
(b) File name starts with ‘M’ that represents the screen image, which includes the index information of hour, minute, and
second thereafter.
(c) In case backup file is created at the same time up to second, it increases the far end index information.

5. Structure of path at live image recording

(1) ‘Movie’ directory will be formed at the sub route directory of USB/CF/SD storage device
(2) Recorded live image is stored below the Movie Directory.
(3) Live image file has the name made of year/month/date/hour/minute/second information when it was created.
(a) Backup file will be created in AVI type. H.264 and Mp3 were used for Video CODEC and Audio CODEC respectively.
(b) File name starts with ‘MOV’ that represents screen image, which includes data and hour information thereafter.
(c) Live image can be stored up to the number 1,000 files. This number can be designated at the special device settings of
XP-Builder.

6. Structure of path when Blue Screen of camera image and live image is created
(1) ‘MovieStill’ directory will be formed at the sub route directory of USB/CF/SD storage device.
(2) Recorded live image will be stored below MovieStill directory.
(3) Blue screen image file has the name made of year/month/date/hour/minute/second information when it was created.
(a) Backup file will be created in JPG type.
(b) File name starts with ‘STL’ that represents screen image, which includes data and hour information thereafter.
(c) Live image can be stored up to 1,000 files. This number can be designated at the special device settings of XP-Builder.

Remark
(1) When changing device time, in case of changing current time into after time, we guarantee the normal operation. But in
case of changing current time into early time, we don’t guarantee the normal operation. In this case, you have to delete
directory including the changed hour and its lower directory for normal operation. For example, if you change time from
th th th
December 10 to December 5 , you have to delete year, month directory created in December 10 and restart the device
(2) Sorting by project is not supported for each logging, recipe, screen image. For example, there are no.1, 2, and 3 logging
groups in the project A. And in case each logging group backups the file, 1, 2, 3 directories are created and each data is
saved under each directory. Then, in case file backup occurs in the project B having no.1, 2 logging group, backup file is
created in same directory of project A. In this case, you have to sort the backup files of project A and B based on the
created time.

9-3
 Chapter 9. File Backup through External Storage Equipment

9.2 Operation setting when there is no space for backup

You can designate in the XP-Builder whether to cancel the backup or delete the oldest backup file and execute backup when
there is no space in the storage equipment.
[Project Property Setting -> Storage Settings -> Backup Storage -> Delete old file if disk full]

1. In case of backup, deleting the oldest data

(1) In case there is no space for backup, searches the oldest year, month directory under Logging, Recipe, Screen Image. (But
in case of Logging, finds under Logging number directory. That is, when executing backup about Logging number 2, in
case there is no backup data in Logging number 2 directory and there is data only in logging number 1, data of logging
number 1 is not searched/deleted.)
(2) Searches the oldest day directory under the oldest year, month directory.
(3) Searches the oldest hour directory under the oldest day directory.
(4) Deletes the oldest backup file under the oldest hour directory
(5) Checks the space and if more space is necessary, the above steps of (1) ~ (4) are repeated and checks the space.
(6) When deleting file, in case all data in time directory are deleted, relevant hour directory is deleted.
(7) When deleting hour directory, in case all hour directories in day directory are deleted, relevant hour directory is deleted.
(8) When deleting day directory, in case all day directories in year, month directory are deleted, relevant year, month directory is
deleted.

Remark
(1) In unknown directory or file (user file or directory), searches the oldest thing among normal backup files except unknown
directory or file.
(2) In case there is nothing except user data in now searched directory, backup operation fails. XGT Panel can’t delete user
data, at this point, operation stops.

9.3 Structure of path of video file and video capture files

1. Movement when file is added

(1) When the name of created file is MOV_120220_121212.avi, the directory will be created as follow;

(2) When MOV_120220_200101.avi file is created again thereafter, the applicsable directory is added by subdirectories as
follow until it fills 500 files.

9-4
 Chapter 9. File Backup through External Storage Equipment

(3) When 500 files are filled with MOV_120330_110101.avi as its last one, the name of directory will be change as follow;

st
(4) When the 501 file (MOV_120330_110230.avi) is created, a new directory will be created as follow;

2. Movement when the domain is short or it exceeds the designated limit

(1) In case of designating the property related with storage device for the XP-Builder project – At the time of setting video file and
video capture, if you check at [Delete Old File when Domain is full], it operates by deleting the oldest file when the space is
short or it exceeds the limited number of directories. When you release such check, it stops operation together with error
code when the space is short.
(2) When the number of directories filled with 500 files becomes 100;
- It deletes the oldest file in the oldest directory. When the directory gets empty, that directory is also deleted.
(3) When there is no available space in the storage device;
- It deletes the oldest file in the oldest directory. It requires minimum 10MB to save the live image and minimum 1MB to
save video capture file. It deletes out the oldest file one by one until such space is secured. When the directory gets
empty, that directory is also deleted.

3. ActiveSync –related movement

(1) When in connection with ActiveSync

When in connection with ActiveSync, it doesn’t make any specific operation. In case you deletes and move the file in the
storage device with ActiveSync in connection, the applicable mode is not reflected in the motion of device. That is, deletion of
file doesn’t cause update of the device of the number of video files or the value of video capture file device.
(2) When out of connection with ActiveSync
When out of connection with ActiveSync, it renews the list of stored video file and video capture file in the storage device
again. During this time, it is impossible to start recording or replaying. Through the status device, you can confirm when the
motion of file list preparation will be stopped.

4. Motion when dismounting the storage device

(1) When mounting the storage device

Please scan the entire video file and video capture file, prepare the list, and find out the total number. During this time, it is
impossible to start recording or replaying. Through the status device, you can confirm when the motion of file list preparation
will be stopped.

9-5
 Chapter 9. File Backup through External Storage Equipment

9.4 Monitoring Connection Status of External Storage Equipment

XGT Panels monitors connection status about external storage equipment designated when setting backup path in XP-Builder.
The following figure is backup path specified in XP-Builder.

In order to use this monitoring function, you have to set about system alarm window

9-6
 Chapter 9. File Backup through External Storage Equipment

In case USB storage equipment (or CF storage equipment) is removed during operation after setting the path for saving Logging
backup file as USB storage equipment (or CF storage equipment) and downloading the project into device, the designated system
alarm (HS951.0) is set. In case storage equipment is equipped again, alarm is reset.
In case USB storage equipment (or CF storage equipment) is removed during operation after setting the path for saving Recipe
backup file as USB storage equipment (or CF storage equipment) and downloading the project into device, the designated system
alarm (HS951.1) is set. In case storage equipment is equipped again, alarm is reset.
In case USB storage equipment (or CF storage equipment) is removed during operation after setting the path for saving Screen
Image backup file as USB storage equipment (or CF storage equipment) and downloading the project into device, the designated
system alarm (HS951.2) is set. In case storage equipment is equipped again, alarm is reset.

Internal address of the designated system alarm can be checked in XP-Builder as follows.

9.5 Safety Removal Switch

In order to remove the storage device, you can use safety removal switch to guarantee that data was backed up with safety

LED is turned off if you remove the storage device right away without any motion of safety removal switch. If you operate safety
removal switch, LED will be turned off right away if there is no backup function with storage device in current use. In that case, LED
will be turned off when such work is all over, and will internally turn off the connection with the storage device. That is, when LED is
turned off, you cannot backup anything in the storage device, and may not use data in the storage device such as file recipe, etc.
Therefore, you need to remove and then mount the storage device again in order to operate safety removal switch and then use it
again after LED is turned off. When you operate safety removal switch and re-mount the storage device, you are required to re-
mount it at least after 5 seconds in case of SD card while 3 seconds in case of CF card.

With the following function in operation, LED will not be turned off even with safety removal switch in operation. LED will be turned
off with the applicable mode completed. It will not be turned off during the creation of backup data or during the Read mode in the
XP-Builder. It will not be turned off during the Load mode as the image stored in XP-User Image in the storage device is use d as
part image. It will not be turned off during the file recipe Write or Read mode. It will not be turned off during Backup Data Read
mode in XP-Server using the XP-Link communication. It will not be turned off during the Inquiry mode of the list of backup files to be
uploaded from the XP-Builder. It will not be turned off during the Load mode of sound file or image included in the Project. It will not
be turned off during the Read mode of Project Backup Data with the storage device or from the XP-Builder. It will not be turned off
when it downloads the project in the device using XP-Builder or storage device. It will not be turned off when it is changing the start
menu image. It will not be turned off with the ladder monitor program stored in the storage device in operation.

9-7
 Chapter 9. File Backup through External Storage Equipment

Function Sub-classification Movement

Alarm Write
Logging Write
Recipe Write
Data Backup Screen Write
Memo Write
Video Write
Still Shot Write
Alarm Read
Logging Read
Recipe Read
Data Upload Screen Read
Memo Read
Video Read
Still Shot Read
Part Image Read
Function-wise Data File Recipe Edit Read/Write
File Recipe Transfer Read/Write
Web Server Webpage Create Write
XP Link File Transfer Read
File List Inquiry Read
Project Backup – Communication Read
Project Upload
Project Backup - Storage Device Write
Image Write
Project Download Sound Write
Project Backup Write
Download Write
Ladder Monitor
Execute Read
Changing default Image Read
Storage Device Download Project Data Read

9-8
 Chapter 10. Installation and Wiring

Chapter 10 Installation and Wiring

10.1 Installation

10.1.1 Installation environment

This machine has high reliability regardless environment. But for reliability and stability, be careful the followings

(1) Environment condition

(a) Install at the panel which can protect this machine from water and dust.
XGT Panel is designed by IP65 Standard in front parts and IP20 Standard in rear parts.
(b) Install at the place where impact and vibration is not continuously applied.
XGT Panel is designed to meet IEC standard (IEC 61131-2).
(c) Do not expose this machine to direct light.
(d) Do not install at the place where rapid temperature change can occur.
Moisture by rapid temperature change can cause malfunction and damage.
(e) This machine should be installed within 0 ~ 50°C, otherwise the screen may be changed or cause malfunction
(f) This machine should be installed within 10~85% relative-humidity.
Moisture by rapid temperature change can cause malfunction and damage.
(g) Avoid corrosive gas and burnable gas.

(2) Installation construction

(a) When doing screw’s processing or wiring construction, be careful that the remains do not enter the XGT Panel inside.
(b) Install at the place where you can easily control.
(c) Do not install with high voltage machine within same Panel.
(d) Keep distance of more than 100mm from duct for wiring and peripheral machine.
(e) Ground at the place where few noises develop.

(3) Anti-heat design of control panel

(a) In case of installing XGT Panel in the airtight panel, consider the heat by other machine as well as own heat. In case that the
air circulates through a ventilating opening or a general pan, XGT Panel system can be influenced by in-draft of dust or gas.
(b) We recommend you to install a filter or to use an airtight heat exchanger.

Remark
(1) Protection standard
1) Ingress Protection (IP) is based on the IEC 60529 Standard for degrees of protection provided by enclosures.
It includes the degree of protection against solid objects and of protection against water ingress.
2) IP65 rating guarantees the enclosure is dust proof (6) and protected against jets of water (5).
3) IP20 rating guarantees protection from solid foreign objects of 12mm diameter and greater (2), but it does not
guarantee protection from water ingress.

10-1
 Chapter 10. Installation and Wiring

<Source: IEC60529>
(2) Caution
1) The XGT Panel is designed to mount on the panel, so that the front side meets the standard. However,
it does not guarantee the installation environment.
2) The product may malfunction or break down if the installation environment is not suitable for the protection rating.
3) The standard is only for protection from dust and water. Use care to protect against oil, corrosives, or metal particles.
4) If the gasket breaks down due to exposure to chemicals or continuous vibration, the protection from dust and
water may be weakened.
5) When you install or mount the XGT Panel, be careful not to damage the product.

10.1.2 Notice in handling

It describes the notice from opening to installation.
• Do not drop or cause heavy impact.
• Do not disassemble voluntarily. When doing this, we are not responsible for the product.
• When wiring, be careful that the remains do not enter into XGT Panel.

10-2
 Chapter 10. Installation and Wiring

10.1.3 Notice in installing the panel

Here describes how to install XGT Panel in panel and notice.

(1) Panel cut

• Before installing the XGT Panel in panel, panel should be made with the following dimension.

Unit: [mm]
Classification X (Wide) Y (Height) Z (Thickness)
+1 +1
iXP70-TTA 259.0 201.0
-0 -0
+1 +1
iXP80-TTA 301.5 227.5 1.6-9.5
-0 -0
+1 +1
iXP90-TTA 383.5 282.5
-0 -0

X Z

10-3
 Chapter 10. Installation and Wiring

(2) XGT Panel installation

Unit: [mm]

100

100
100 100

100

• Keep the distance of 100 mm between XGT Panel and panel per each direction.

Remark
(1) To be affected at a minimum by the electromagnetic waves (radial noise) or heat from other controllers, it needs to keep its
distance as the above explanation.
(2) When installing, consider the power and communication cable wiring.
(3) If the size of the panel cutout dimensions are beyond the error range (0-1mm), the contact surface between the
gasket and the panel may be reduced. This may weaken the protection from water and dust ingress.

• When mounting the XGT Panel inside a panel, ensure that you use the gasket to protect against dust or water ingress.

Dustproof / Waterproof
gasket

10-4
 Chapter 10. Installation and Wiring

Remark
(1) Use the gasket to prevent dust or other contaminant ingress.
(2) When you mount the XGT Panel on the panel, if the surface of panel is uneven, water or dust can enter the product
through the gaps. This can be caused by the quality of the material (iron, aluminum, or acrylic) or the thickness, so check
the installation environment carefully. Moreover, be sure to adhere the gasket and panel.
(3) If the gasket is damaged when you install the product or is deteriorated after a long period of use, it may weaken the
protection from water and dust ingress. If you need to replace it, contact the agency or a service center.

(3) Installation location

• When installing the XGT Panel, consider screen and use of touch.
• When you don’t see within the following angle, you may not see clearly. When installing, consider angle.

Item Left and Right Upper Lower

iXP70-TTA 80 deg. 60 deg. 80 deg.

iXP80-TTA 80 deg. 60 deg. 80 deg.

iXP90-TTA 80 deg. 60 deg. 80 deg.

(4) Fixation

• Fix XGT Panel to the panel using the supplied brackets provided in the OEM packaging.

Affix using supplied brackets

Panel

Affix using
supplied brackets

Affix using
supplied brackets

Affix using supplied brackets

10-5
 Chapter 10. Installation and Wiring

Remark
(1) Affix the brackets on four sides of the product to prevent ingress by water and dust.
(2) Affix the brackets top to bottom and right to left to prevent gaps.
(3) Align the brackets vertically with the panel. The screw torque of the brackets is 6.42kgf/cm. The screw torque may vary
by the quality of the panel, but it should follow the standard screw torque value for a bolt. If you apply excessive force
when affixing the brackets, the XGT Panel can be damaged. This may result in touch screen errors or weaken the
protection against water and dust ingress.
(4) After mounting the XGT Panel on the panel, remove the screen protection film. Touch screen errors may result if the film
is not removed. To protect the screen, use the exclusive protection sheet. To purchase a protection sheet, contact the
agency or a sales office.

10.2 Wiring

It describes the wiring that you should know when installing the XGT Panel.

10.2.1 Power wiring

XGT Panel is divided into the DC product and the AC product.

Power Name
iXP70-TTA/DC
DC 12/24V iXP80-TTA/DC
iXP90-TTA/DC
iXP70-TTA/AC
AC 100-240V iXP80-TTA/AC
iXP90-TTA/AC

Warning
► If AC power is applied into the product for DC power, It may cause damage or fire.
Be careful of connection.

► ‘/DC’ is the product which use DC 12/24V, and ‘/AC’ is the product which use AC 100-240V.
When using the product, Please check the label in the back of the product.

10-6
 Chapter 10. Installation and Wiring

The power terminal should have the following specification.

Ø3.2 Ø3.2

Less than Less than

6.00mm 6.00mm

The power cable should have the following specification.

Type Cable specification (Unit: ㎟)

Power and protection ground 1.5 (AWG16) ~ 2.5 (AWG12)

Remark
(1) For installations where there is voltage drop, it is recommended to use stranded wire with a cross sectional area
1.5~2.5 ㎟.
(2) It is recommended that cable connections are twisted and secure. Short cable runs are also recommended
Between the point of supply and the XGT panel.
(3) For safety reasons it is recommended that you use color coded outer sheaths on the conductors to aid safe
terminations.
Follow local regulations when making electrical connections.

Wiring of power is as follows.

FG

DC Power connection

10-7
 Chapter 10. Installation and Wiring

AC Power
100-240 V
FG

AC power connection

Remark
(1) Use a regulated power supply transformer when the power fluctuation is bigger than the standard.
(2) If electromagnetic interference is experienced or expected use an insulation transformer to protect the XGT panel
from interference.

Separate the XGT Panel power from the I/O device and main circuit device.

Main Power XGT Panel power Constant

Voltage
Transformer

I/O power
I/O device

Main circuit power

Main circuit device

Remark
(1) Separate the XGT Panel power supply cable from the main circuit cable (high voltage and current) and
input/output cable. Maintain a minimum separation of 100mm between cables.

10-8
 Chapter 10. Installation and Wiring

Use a lightning surge protector to prevent damage from lightning strikes.

XGT Panel

E1
E2

Surge absorber to prevent the lighting

Remark
(1) Separate E1, the ground connection for lightning surge protector, and E2, the ground connection for XGT Panel.
(2) Set lightning surge protector to below the allowable surge voltage to provide protection if the voltage increases to
its maximum.

Use an insulation shielding transformer or noise filter when the electromagnetic interference occurs. Keep the stripped ends of
the terminated cables twisted and as short as possible. When running the wiring avoid running the cables for the insulation
shielding transformer or noise filter pass through the cable duct.

When you use the magnetic lighting contactor (MC) for AC/DC, it is recommended to use a ferrite core close to the power
terminals as shown below:

Ferrite core
(CU1330B, E-TECH)
(CU1330G, E-TECH)
(ZCAT3035-1330, TDK)

10-9
 Chapter 10. Installation and Wiring

10.2.2 Ground wiring

(1) Our XGT Panel has enough anti-noise measure, so except that there are many noises specially, the ground is not needed.
When you use the ground connection, refer to the following information.

(2) Use the exclusive ground connection. When you install the ground connection, use the third grounding resistance
(less than 100Ω).

(3) If you cannot use the exclusive ground connection, use the common ground connection like below.

XGT Other XGT Other XGT Other

Panel devices Panel devices Panel devices

3rd grounding connection 3rd grounding connection

A) Exclusive ground: Best B) Common ground: Good C) Common ground: Poor

(4) Use cables for grounding/earth connections by using cable with a cross sectional area greater than 2.0 ㎟. Install the ground
connection as close as possible to the XGT Panel.

Remark
(1) Check and test the grounding connection. If the connection is bad or in case of (B) above, the XGT Panel may
malfunction or the communication signals may fail.

10-10
 Chapter 11. Maintenance

Chapter 11 Maintenance

To keep the XGT Panel best, examine the XGT Panel.

11.1 Maintenance

Because an error may be developed by environment, the periodic maintenance is needed. You should check the following
categories once or twice every 6 months.
Maintenance category Criterion Action
Within the power change range Modify the source of electric power in order to be in the
Power
(Within −15% / +10%) fluctuation range of a permissible voltage.
Operating
0 ~ + 50 ℃
temperature
Modify the operating temperature and humidity to be proper.
Environment Operating
10 ~ 85%RH
humidity
Vibration No vibration Use the anti-vibration rubber and make a count measure.

Getting loose of power terminal There is no unwinding Screw the unwound terminal.
Getting loose of communication
There is no unwinding Screw the unwound terminal.
connector
Amount of reserved part and
Reserved part reservation Refill the insufficiency and improve the reservation.
Check the status
No gap between the gasket and
Gasket installation status Replace gasket or affix brackets firmly
panel.

Gasket status No damage or deterioration Replace gasket

11.2 Daily Maintenance

Check the followings daily.

Maintenance category Maintenance contents Criterion Action
Retighten
Mounting status Check the brackets Should be mounted firmly
screws
Retighten
Loose terminal screws Not loose
screws
Power terminal status
Reduce the distance between
Keep the proper distance. Correction
compressed terminals.
Communication connector Retighten
Unwinding of fixed screw Not loose
status screws
Refer to the
Indication LED Check the lighting Green LED should be turned on
appendix 1.

11-1
 Chapter 11. Maintenance

11.3 Periodical Maintenance

Check the followings once or twice every six months and take measure.
Maintenance category Maintenance method Criterion Action
Surrounding
0 ~ 50 °C Modify it to meet the general
temperature Measure through
standard.
Environment Surrounding humidity temperature/Hygrometer 10 ~ 85%RH
(environment standard in the
Surrounding pollution Measure of corrosive gas
No corrosive gas. panel)
degree
Unwinding, swing Move XGT Panel Fixed firmly Retighten screws
XGT Panel
Status Dust, foreign matter
Visual check Not loose -
adhesion
Retighten screw with
Looseness Not loose Retighten screws
Screwdriver
Reduce the distance
between compressed Visual check Keep the proper distance. Correction
Connection
terminals.
status
Wind the fixed screw of
Loose connectors Visual check Not loose
connector
Retighten screw with
Loose brackets Not loose Retighten screws
Screwdriver
Check the power voltage of
AC100~240V: AC85~ 264V
Power voltage maintenance input terminal of power by Supply power modification
DC24V: DC19.2 ~ 28.8V
test
• Check the total of power If guarantee duration is
Check when battery is
stoppage time and exceeded even tough there is
exchanged and voltage drop
Battery guarantee duration
is indicated (It is expressed no battery voltage drop
• There is no battery voltage
by system alarm) indication, change the battery.
drop indication
When error occurs, change
LCD Backlight maintenance Visual check Check the guarantee duration
the backlight.
Check at the Diagnostics of Reset at the setting of XGT
Touch location error Appropriate touch location
Touch XGT Panel Panel.
status Damage or deterioration There is no damage or When error occurs, change
Visual check
of protection sheet deterioration protection sheet

11-2
 Chapter 11. Maintenance

Remark
(1) Battery exchange time is expressed by alarm. System alarm is expressed when system alarm category is set at the
XP-Builder as follows.

(2) iXP model LCD backlight is not replaceable. Therefore when backlight has some problem or it is no longer of any use,
LCD has to be replaced.

11-3
 Chapter 12. EMC Standard Certification

Chapter 12 EMC Standard Certification

12.1 Requirement for EMC Standard Certification

EMC command is regulated on “It doesn’t produce the Strong electromagnetic waves: Emission” and “It is not affected by
electromagnetic wave from external: Immunity”. The following is describing the contents to meet the EMC command when configuring
the system by using the XGT Panel. This is a summary document for the request and standard which our company has obtained
from EMC but we don't assure that all devices manufactured according to these contents are not suitable for the below standards. The
final manufacturer needs to finally judge about the fitness method or fitness judgment of EMC command.

12.1.1 CE standard certification

Applied Standards Results

1. Emission

Conducted Disturbance EN61000-6-4:2007 C

Radiated Disturbance EN61000-6-4:2007 C

주2)
NA
Harmonic Current Emission EN61000-3-2:2006 / A2 : 2009 주3)
NT
주2)
NA
Voltage Change, Fluctuations and Flicker EN61000-3-3:2008 주3)
NT
2. Immunity
EN61000-6-2:2005
Electrostatic Discharge C
EN61000-4-2:2009
EN61000-6-2:2005
Radio-Frequency Electromagnetic Field C
EN61000-4-3:2006 / A1 : 2008
EN61000-6-2:2005
Fast Transient C
EN61000-4-4:2004
EN61000-6-2:2005
Radio-Frequency Continuous Conducted C
EN61000-4-6:2009
EN61000-6-2:2005
Power-Frequency Magnetic Fields C
EN61000-4-8:1993 / A1 : 2001
EN61000-6-2:2005
Surges C
EN61000-4-5:2006
주2)
EN61000-6-2:2005 NA
Voltage Dips and Interruptions 주3)
EN61000-4-11:2004 C
RE1) C=Conform NC=Not Conform NT=Not Tested NA=Not Applicable
RE2) Applicable to the only iXP70-TTA/DC, iXP80-TTA/DC, iXP90-TTA/DC
RE3) Applicable to the only iXP70-TTAAC, iXP80-TTA/AC, iXP90-TTA/AC

12-1
 Chapter 12. EMC Standard Certification

Directive:

Electromagnetic Compatibility Directive 89/336/EEC amended by the Directive 93/68/EEC

12.1.2 KC standard certification

The XGT Panel acquire the electromagnetic fitness registration (KC specification) certified by wave laboratory under information-
communication part.

A grade device

This device acquires KC for industrial use.

If device is not purchased properly, exchange it to device for home use.

12.2 Requirement for Low Voltage Command Suitability

It is required to get the needed Stability for the device operated at AC50~1000V, DC75~1500V’s power. The following describes
attention about installation and wiring for the suitability when using the XGT Panel. Though the following data is made by requirement
of regulation and standard, we don’t guarantee that all devices are suitable for the above command. The method to be suitable for the
EMC command and judgment of suitability should be finally made by device manufacturer himself.

12.2.1 Standard certification for XGT Panel

XGT Panel is according to the EN61131-2:2007 (stability of device used in the measure, control laboratory).
XGT Panel, iXP70-TTA /AC, iXP80-TTA /AC and iXP90-TTA /AC, is made to meet the above standard.

12.2.2 Selection of XGT Panel

(1) iXP70-TTA/AC, iXP80-TTA/AC, iXP90-TTA/AC
Because the Power module whose rated input voltage is AC100-240V has danger voltage (voltage of more than 42.4V),
the product which is suitable for CE mark is having the improved insulation between internal 1 and 2.

(2) iXP70-TTA/DC, iXP80-TTA/DC, iXP90-TTA/DC

The I/O module under DC12V exceeds the range of low voltage command target.

12-2
 Appendix 1. Troubleshooting

Appendix 1 Troubleshooting

1.1. Type of Problem

It classifies problems from XGT Panel including an indicated figure, indication of the object, and problems appeared when
downloading. Refer to the following chart.

Classification of problem Description

Problem when starting Malfunction when starting.
☞Please refer to the 2. Problem when starting.
Problem when touching In case that there is no reaction when touching.
☞ Please refer to the 3. Reaction problem when touching.
Display problem of figure and In case that the figure or object is different from when editing.
object. ☞ Please refer to the 4. Indication problem of figure and object.
Communication problem In case that communication is not executed properly.
☞ Please refer to the 5. Communication problem.

Error message when In case that an error message occurs when operating the XGT Panel.
executing program ☞ Please refer to the 6. Error message when executing program.

1.2. Problem when Starting

Why does black screen show up when turning on the device?

Phenomenon: When turning on the device, black screen shows up and the booting is impossible.

< Cause >

(1) Because the device is not set as a booting mode.
(2) Black screen may appear because of malfunction of backlight.
<Solution>
(1) because the device is not set as a booting mode, the above problem can occur. Check whether the number 2 switch
at DIP switch in the back of the device is in A direction or not.

When is the color of LED changed?

Please check the followings.

Display color Contents

GREEN Power is supplied to XGT Panel

App.1-1
 Appendix 1. Troubleshooting

1.3. Reaction Problem when Touching

When touching the screen it reacts in a different area or it may not react at all?

Phenomenon: When touching the screen it reacts in a different area or it may not react at all.

< Cause >

(1)Touch’s Calibration setting is not proper.
(2) Touch panel may be a break down.
<Solution>
(1) Redo Calibration setting about touch. Refer to the [Device manual Ch.4.1 Touch Calibration].
(2) It you can’t go to setting menu, connect mouse to USB port and use mouse.

Buzzer does not sound.

Phenomenon: When pressing buzzer, buzzer does not sound.

< Cause >

(1) When that the switch operates but the buzzer doesn’t sound, the buzzer is set as no sound.
(2) If the switch doesn’t work too, it seems that some error occurs in the touch function.
<Solution>
(1) Redo environment setting for buzzer to sound. Refer to the [device manual Ch.4.7 Environment Setting].
(2) After setting to use buzzer, check whether the buzzer sounds or not in the 1)’s setting windows.

There is no sound during the video recording

Phenomenon: Sound is not saved at the time of video recording

<Cause>
(1) Sound input may be abnormal.
(2) Sound is not recorded when the sound input is connected with sound output.

<Solution>
(1) Be sure to check the sound input is normal. Check [Line-in/MIC bypass to speaker] in the XGT Panel start menu
[Settings]-[Buzzer & Sound], connect the sound input to the speaker, and then confirm if the input sound comes out
through the speaker or not.
(2) Release the check on [Line-in/MIC bypass to speaker] in the XGT Panel start menu [Settings]-[Buzzer & Sound].
(3) Microphone with power not applied like ear microphone does not accept the sound input.

App.1-2
 Appendix 1. Troubleshooting

1.4. Display Problem of Figure and Object

The shape of object is not shown or the number or character value which has to be shown is not shown.

Phenomenon: The shape of object is not shown or the number or character value which has to be shown is not shown.

<Cause>
(1) The connection with PLC connected with each project is disconnected or NAK occurs.
<Solution>
(1) When the communication is executed at first, Check the cable connected with PLC is OK or not.
(2) If object where the offset is set is not shown, check whether address range is exceeded or not.
(3) In case that communication is not OK, when communication is abnormal, the following message shows up in the
XGT Panel.

Object type Phenomenon

Bit Switch The switch is expressed but it doesn’t work.
Word Switch The switch is expressed but it doesn’t work.
Change Screen Switch The switch is expressed but it doesn’t work.
Special Switch The switch is expressed but it doesn’t work.
Multi Switch The switch is expressed but it doesn’t work.
Bit Lamp Image is not shown.
Word Lamp Image is not shown.
N-State Lamp Image is not shown.
Clock Present time is shown.
Bit Message Message is not shown. When designating the background image, image is shown as it is.
Word Message Message is not shown. When designating the background image, image is shown as it is.
Numeric Display The value is not shown. When designating the background image, image is shown as it is.
Numeric input The value is not shown. When designating the background image, image is shown as it is.
Text Display Character string is not shown. When designating the background image, image is shown as it is.
Text Input Character string is not shown. When designating the background image, image is shown as it is.
Bit Window The window screen set in the object is not shown. But if communication is set with other object in
the same window screen, it can be shown by that object.
Word Window The window screen set in the object is not shown. But if communication is set with other object in
the same window screen, it can be shown by that object.
Bit Part The part screen set in the object is not shown. But if communication is set with other object in the
same part screen, it can be shown by that object.
Word Part The part screen set in the object is not shown. But if communication is set with other object in the
same part screen, it can be shown by that object.

Animation Animation is not shown.

Bar Graph Graph is not shown. When designating the background image, image is shown as it is.
Pie Graph Graph is not shown. When designating the background image, image is shown as it is.
Meter Graph Graph is not shown. When designating the background image, image is shown as it is.
Closed Graph Graph is not shown. When designating the background image, image is shown as it is.
Trend Graph X, Y axis is shown normally but trend axis is not normally shown. When designating the
background image, image is shown as it is.

App.1-3
 Appendix 1. Troubleshooting

Object type Phenomenon

History Alarm Viewer Change doesn’t occur. When communication is abnormal, alarm occurs because it can’t know
the status of alarm target device. But previous alarm data shows up as it is.
Data list Value is not shown. Lattice of viewing data list of object is shown as it is.
Logging Viewer Change doesn’t occur. When communication is normal, the recorded log data is shown normally.
But, log data is shown as # when communication is abnormal.
Navigator Change doesn’t occur. Because it shows the group of alarm already developed, though
communication is abnormal, if it has alarm data already developed, it shows the name of group
where each alarm is included.

The number indication object value is shown as # or ~.

Phenomenon: The number indication object value is shown as # or ~.

(Same phenomenon occurs at the number input device, viewing data list, and viewing logging)

<Cause>
(1) This happens when digit is not correct or type is not BCD.
<Solution>
(1) When the number to be expressed exceeds the number set in the object, # is expressed. In case of this, set the
digit largely and after download again, execute program again.
(2) When the numeric display object is expressed as BCD type, the data whose type is not BCD is expressed as ~.
In case of this, adjust device value as BCD type.
(3) This phenomenon occurs at the data list object, numeric input, numeric display device, and logging viewer.

After switching the screen, the previous screen remains for a few minute.

Phenomenon: After switching the screen, when there is no background or image in the part or number indication device,
the previous screen remains for a few minute because of change of part.

< Cause >

(1) After switching the screen, when connection is set up multiply or communication time-out occurs, the screen of
previous part remains in some object.
<Solution>
(1) It is normal status. In case that multiple connection or communication is not good, when switching the screen, the
remains of previous screen can occur during the time-out hour.

The folded object doesn’t sequentially show up.

Phenomenon: The number under the data list shows up above data list.

< Cause >

(1) The device value is expressed at the top of object screen.
<Solution>
(1) It is normal status. The folded window or part object is not included in screen, regardless of sequence of drawing,
the object changed recently is expressed at top of screen. So if possible, do not fold the object in screen.

App.1-4
 Appendix 1. Troubleshooting

The object always shows up above the figure.

Phenomenon: I downloaded the figure above the object in XP-Builder, but the object always shows up above the figure.

< Cause >

(1) In XGT Panel, The object always shows up above the figure.
<Solution>
(1) It is normal status. The object always shows up above figure in the XGT Panel.

Live image player doesn’t show the camera screen.

Phenomenon: XP-Builder deployed live image player on the screen and performed download, but the area of live image
player is displayed in blue or black color when starting monitoring.

<Cause>
(1) In case of being displayed in blue color, it means the camera-related function is not working in normal condition owing
to software problem. In case of being displayed in black color, it means the function is in a normal condition, but
camera is wrongly connected.

<Solution>
(1) In case of being displayed in blue color, please update iXP-Runtime again. If there still exists the same problem, please
consult the A/S Center nearby. In case of being displayed in black color, please check for the cable connected with
camera on the device. It may be a faulty connection between camera and cable or between iXP and cable.

Pop up window doesn’t show camera screen.

Phenomenon: In the XP-Builder, the user deployed live image player on the pop up window (Nominating as global window
or window object), but it doesn’t show camera screen.

<Cause>
(1) Camera object is displayed only through a single object on the whole screen. That is, if the image started to be displayed
on window screen, the live image player on the other screen such as basic screen doesn’t display any more. Live image
play is also displayed through an object only. Likewise, if the image is being played, the other live image player object
doesn’t play.

<Solution>
(1) Please touch the special switch for pause among those connected with the object of live image player now under play,
and then start playing by pushing the special switch for start placed on the desired screen.

App.1-5
 Appendix 1. Troubleshooting

Live image is not recorded.

Phenomenon: The user designated the record start device in the XP-Builder, and downloaded it, and turn the device On,
but it is not recorded.

<Cause>
Some causes may lead to such situation as follow;
(1) Please check for the connection of communication between Record Start device and iXP.
(2) Please check that the storage device designated as record file storage path on the project property storage device
settings is properly mounted on the actual device.
(3) Be sure to check for any room in the designated storage device.
(4) Please check that the number of recorded files stored in the designated storage device should not exceed the number
of maximum record file designated in the project property special device setting window.
(5) The user may watch the image input from the current camera and carry out recording simultaneously, but may not play
the recorded live image and carry out recording simultaneously. That is, please try recording again with the play of live
image stopped.

<Solution>
(1) You can confirm through the device with applicable error number from which cause such failure of recording took place.
Device with error number falls under the next word of the state device. That is, if you designated the state device as
HW00, HW01 represents the device with error number. In the case of troubles related with the afore-mentioned cause,
you can check it through the device with error number as follow;
1: Record file path cannot be created (Required to check the storage device is mounted)
2: Currently live image is being played (Required to record after stopping the live image play)
3: Already under recording at present (Required to record after checking the recording under process is finished)
4: Being in excess of the designated number of maximum files (Required to record after erasing of backing up the live
image file already recorded)
5: Insufficient room in the designated storage device. (Required to record after erasing of backing up the live image file
already recorded)
6: Video file storage path is not designated in the XP-Builder.
7: Currently file cannot be created in the storage device.

App.1-6
 Appendix 1. Troubleshooting

1.5. Communication Problem

It seems that communication does not work.

Phenomenon: On the screen where the object is not many, communication works but when you move the screen where
the object is many, timeout occurs.

< Cause >

(1) In the device setting, the communication time-out is set to be too short.
<Solution>
(1) It occurs because timeout is set much smaller than sum of request time of communication data and response time
from PLC. In the device setting at the XP-Builder, after setting communication time out to be big, download
program and execute again.

It seems that communication doesn’t work.

Phenomenon: Communication doesn’t work.

< Cause >

(1) Communication setting or cable may be not normal.
<Solution>
(1) In case of RS-232C, check whether connection setting is normal or not in XP-Builder.
(2) In case of RS-422/485, check whether station and communication connection setting is normal or not.
(3) If 1), 2) is normal, do diagnosis about PLC-RS232C, PLC-RS485/422 at the Serial diagnosis screen of device
menu. Refer to the [Device manual ch.5.6 Serial Communication Diagnosis]
(4) If 3) is normal, check whether connection cable has error or not.
(5) In case of Ethernet, check the port and IP setting about relative PLC.

Caution
► Before trial operation of the product, be sure to check if a normal communication is available between
XGT Panel and the subject device of control

App.1-7
 Appendix 1. Troubleshooting

1.6. CF/SD/USB Removal of Memory Card

When removing the CF/SD/USB memory card, device is stopped for some times.

Phenomenon: This happens when doing data backup including logging, recipe.

< Cause >

(1) This happens because memory card is removed when doing data backup.
<Solution>
(1) If possible, when monitoring XGT Panel, do not remove the memory card and after going out to the waiting screen,
execute the removing.
(2) Inescapably you have to remove it during the operation, remove when backup does not occur. If the above
phenomenon occurs, it works normally after about 10 seconds.
(3) In case of USB memory, please remove it when the LED of USB external memory is not flickering.
(4) In case of CF and SD memory cards, please remove it if LED is Off after the safety removal switch is turned On.

Caution
► If you force to remove the data during the storage of data in the external memory, file may not be stored
in a normal condition or external memory may suffer from damage.

App.1-8
 Appendix 1. Troubleshooting

1.7. Error Message during Execution of Program

In case that problems occur during execution of XGT Panel including the start of device, diagnosis of device and environment
setting, project download, monitoring of control device, and error messages occur as type of box. At this time the message
indicates the code made by 4 digit number. The front 2 number indicate code of object and work, the rear 2 number is
message number. In case that the present error message is indicated as [0101], an error message occurs when doing
diagnosis about the status of NVRAM. When an error message occurs, refer to the row’s number and sequence and find the
category of reason and measure.

Error code Occurrence

Object Error message Reason and measure
Type Address location
Failed to check whether backup memory is
NVRAM Data Access ...
0x01 XGT Panel normal or not. If this symptom is repeated,
FAILED!
contact the near Customer Service Center.
Backup data is not valid. If this symptom is
BATTERY STATUS ... repeated when turning power off and on,
0x02 XGT Panel
NOT GOOD! remove XGT Panel’s power and exchange
the battery.
Write Operation The built-in Flash disk has an error. Contact
0x03 XGT Panel
FAILURE! the near Customer Service Center.
Device
0x01 Read Disk Information The built-in Flash disk has an error. Contact
diagnosis 0x04 XGT Panel
Error! the near Customer Service Center.
Check that CF card is empty, and equip CF
Write Operation card and test again. If same symptom is
0x05 XGT Panel
FAILURE! repeated, CF card or CF card slot of XGT
Panel may have a problem.
Check that CF card is empty, and equip CF
Read Disk Information card and test again. If same symptom is
0x06 XGT Panel
Error! repeated, CF card or CF card slot of XGT
Panel may have a problem.
You inputted the wrong time which is not
0x01 XGT Panel Invalid timeout value. within backlight setting time range. Input the
effective time.
There is no setting information data of XGT
Not found XGT Panel Panel. If this symptom is repeated when
Device setting 0x02 0x02 XGT Panel
configuration file. turning power off and on, contact the near
Customer Service Center.
When setting IP, the values within 0~255 are
Please enter an integer
0x03 XGT Panel effective. Input the value within the above
between 0 and 255.
range.
Now, there is no downloaded project so you
Viewing device
0x03 0x01 XGT Panel No project in XGT Panel. can’t see connection information. Download
information
the project from XP-Builder.

App.1-9
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location
Because of update error or Flash disk error,
Failed to Start engine.
XGT Panel program can’t be executed. If you can update,
0x04 0x01 XGT Panel Please update engine
Update redo the above procedure. If you can’t,
again.
contact the near Customer Service Center.
There is password in the each object. When
editing the project downloaded in the present
Switch h05 h01 XGT Panel Invalid password.
device, input the designated password at the
project property information.
Because of communication error, the value
h01 XGT Panel Can't write Data. can’t be inputted. Check the communication
status and input again.
You tried to input with no value. Input the
h02 XGT Panel No input Data.
value
Number Exceeded the max
0x03 XGT Panel You exceed the maximum length to input.
indication length.
device/ 0x06 Exceeded the minimum
0x04 XGT Panel You exceed the maximum value to input.
Number input Value.
device Exceeded the maximum
0x05 XGT Panel You exceed the minimum value to input.
Value.
When you input the value, input can’t be done
because of wrong input. Check the input
0x06 XGT Panel Invalid at Input Case.
condition of each object in the Builder and
input again.
Lamp 0x07 None
Character
indication
device/ 0x08 None
Character input
device
Message 0x09 None
Clock 0x0A None
Animation 0x0B None
Graph 0x0C None
Window 0x0D None
Part 0x0E None
History alarm 0x0F None
Flow alarm 0x20 None
System alarm 0x21 None
Scheduler
0x22 None
related
Recipe
0x23 None
related
Logging
0x24 None
related

App.1-10
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location

Data list 0x25 None

Abnormal send-payload.
Communication status is abnormal. Check
0x00 XGT Panel Please download project
the connection of communication cable.
again.
This message shows up when making it
There's not Password newly because there is no password setting
0x01 XP Builder
File. file in the device. When making it newly, it is
initialized with no password.

It make new password setting file when there

is no password setting file. But downloading is
Failed to Create
0x02 XP Builder stopped when it fails to make this file because
Password File.
of device error. If this problem is repeated,
Contact the near Customer Service Center.

Communication status is abnormal. Route

information is not correct to save project data.
0x03 XP Builder Invalid Backup Media.
If this problem is repeated, Contact the near
Customer Service Center.
In case that the version information file doesn’t
exist in the device, that file is made newly. In
Project
0x26 Failed to Create version case that the device has error and fails to
download 0x04 XP Builder
File. make that file, download is stopped. If this
problem is repeated, Contact the near
Customer Service Center.
There is version information file. In case that
because of error of device, it fails to read
version information, because the device
0x05 XP Builder File Size Error.
doesn’t know version, download is stopped. If
this problem is repeated, Contact the near
Customer Service Center.

In case of not reading file where project

property is included, download is stopped. If
0x06 XP Builder Failed to get Project ID.
this problem is repeated, Contact the near
Customer Service Center.

In case of not reading information about alarm

Failed to read history history because of error of NVRAM, download
0x07 XP Builder
alarm data. is stopped. If this problem is repeated,
Contact the near Customer Service Center.

App.1-11
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location

Project is set to store data at CF card

equipped at device. By the way, now it can’t
Failed to read CF Card read information about CF card. Check the
0x08 XP Builder
information. installation status of CF card and if it is normal,
check the CF card. If this problem is repeated,
contact Customer Service Center.
Project is set to store data at USB storage
device equipped at device. By the way, now it
can’t read information about USB storage
Failed to read USB
0x09 XP Builder device. Check the installation status of USB
information.
storage device and if it is normal, check USB
storage device. If this problem is repeated,
contact Customer Service Center.
In case that it can’t know information about
Failed to read Flash memory status, download is stopped. If this
0x0A XP Builder
memory information. problem is repeated, contact Customer
Service Center.
In case that because of error of Flash Disk, it
can’t delete the directory made temporally for
Failed to clear Temp
0x0B XP Builder download because of error of Flash Disk,
Directory.
download is stopped. If this problem is
repeated, contact Customer Service Center.
Project
0x26 In case that it fail to delete the font file of
download Failed to delete Font File.
previous project because of error of XGT
0x0C XGT Panel Please reboot XGT
Panel, download is stopped. If this problem is
Panel.
repeated, contact Customer Service Center.

In case that it fail to delete the image file of

Failed to delete Image
previous project because of error of XGT
0x0D XGT Panel File. Please reboot XGT
Panel, download is stopped. If this problem is
Panel.
repeated, contact Customer Service Center.

In case that it fail to delete the sound file of

Failed to delete Sound
previous project because of error of XGT
0x0E XGT Panel File. Please reboot XGT
Panel, download is stopped. If this problem is
Panel.
repeated, contact Customer Service Center.

It can’t download part or fixed part in case

There's no downloaded
there is no downloaded project. In case of
0x0F XGT Panel project. It needs to
this, download again. If this problem is
download whole project
repeated, contact Customer Service Center.

App.1-12
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location
When user change the storage location of
project data including image and font, if there
is not respective routine, it make newly. By the
Backup path is invalid.
way, download is stopped in case it fails to
Please check the path
0x10 XP Builder make newly.
that project is
When it is designated as CF card, it can occur
downloaded.
in case CF card is not installed. If this problem
is repeated and not referred in the above,
contact Customer Service Center.
The project backup file downloaded already
Failed to delete previous
can be deleted because of error of XGT
0x11 XGT Panel project archive. Please
Panel. Reboot XGT Panel. If this problem is
reboot XGT Panel.
repeated, contact Customer Service Center.

When downloading, the log data area in the

NV-RAM is initialized in case of selecting
Failed to delete past
previous project’s the monitor data deletion
0x12 XGT Panel project data files. Please
option. By the way, in case of failing this,
download project again.
downloading is stopped. If this problem is
repeated, contact Customer Service Center.
When downloading, the log data area in the
Failed to initialize NV-RAM is initialized in case of selecting
LOGGING area in NV previous project’s the monitor data deletion
0x15 XGT Panel
RAM. Please download option. By the way, in case of failing this,
project again. downloading is stopped. If this problem is
repeated, contact Customer Service Center.
When downloading, the alarm history in the
Failed to initialize NV-RAM is initialized in case of selecting the
Project RECIPE area in NV previous project’s monitor data deletion
0x26 0x16 XGT Panel
download RAM. Please download option. By the way, in case of failing this,
project again. downloading is stopped. If this problem is
repeated, contact Customer Service Center.
Failed to initialize The downloaded font file is moved into
ALARM area in NV original storage location but when this fails,
0x17 XGT Panel
RAM. Please download downloading is stopped. If this symptom is
project again. repeated, contact Customer Service Center.
The project data is divided into several files
Failed to install font files.
according to the contents but when this fails,
0x18 XGT Panel Please download project
downloading is stopped. If this symptom is
again.
repeated, contact Customer Service Center.
The data divided according to the contents is
Failed to unmarshall moved to the original storage location but
0x19 XGT Panel download file. Please when this fails, downloading is stopped. If this
download project again. symptom is repeated, contact Customer
Service Center.

App.1-13
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location
The downloaded project is not installed
Failed to install new
normally because of error of the Flash Disk.
0x1A XGT Panel project data files. Please
Download the project again. If this symptom is
download project again.
repeated, contact Customer Service Center.
The downloaded project zip file is moved to
Failed to merge data
the original storage location but when it fails,
0x1B XGT Panel files. Please download
downloading is stopped. If this symptom is
project again.
repeated, contact Customer Service Center.
There is a program to reboot engine program
after downloading in the device but when it
Failed to save new fails, this message shows up. But because
0x1C XGT Panel project archive. Please the downloading is completed if you reboot
download project again. engine directly, it works normally. The
program name to reboot is startup.exe and it
can be installed by engine upgrade function.
Failed to XGP Panel
startup program. Please It can’t find software to reboot XGT Panel.
0x1D XGT Panel
update XGT Panel Update the XGT Panel.
Software.
The project data was not downloaded
Project data is not normally because of communication error.
Project 0x1E XGT Panel downloaded. Please Check the connection status of
0x26 download project again. communication cable and If this symptom is
download
repeated, contact Customer Service Center.
There is version information file but when it
XGT Failed to read Version can’t read file normally because of the device
0x1F Panel/ information file. Please error, downloading is stopped because it
XP-Builder download project again. doesn’t know version. If this symptom is
repeated, contact Custom Service Center

Cannot find project data There is no USB or device status of USB is

0x51 XGT Panel
in USB Storage not good or project is not saved properly.

Project
download from The project is not saved normally in the USB.
0x27 Project information file is
USB storage 0x52 XGT Panel Check whether there is XP_Project folder and
not in USB Storage.
device [project name].inf in the USB or not.

It can’t read project information file because

Failed to read project the project is not saved in the USB normally.
0x53 XGT Panel
information file. Save the project again from XP-Builder to the
USB.

App.1-14
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location

The connected device type is not same as the

device type set in the project in the USB. In
Device type is not
0x54 XGT Panel case of this, project can’t be downloaded into
matched.
the device. Edit the project again or download
according to the connected device.

Information about the password can’t be red

Cannot read user
0x55 XGT Panel because of the device error. If this symptom is
password.
repeated, contact Customer Service Center.
When saving the project, the password
Password is not inputted by user is not same as present
0x56 XGT Panel
matched. connection password. Input correct password
and save the project.
There is version information file but when it
can’t read file normally because of the device
Cannot read XGT Panel
0x57 XGT Panel error, downloading is stopped because it
software version.
doesn’t know version. If this symptom is
repeated, contact Customer Service Center.
XGT Panel software is The version of XP-Builder where project is
0x58 XGT Panel old version. Please saved is not compatible with present XGT
update XGT Panel. Panel. Update the XGT Panel.
XP-Builder is old version. The version of XP-Builder where project is
0x58 XGT Panel Please update XP- saved is not compatible with present XGT
Builder. Panel. Update the XGT Panel.
There is storage structure version information
file. But when it can’t read this file because of
Project
Cannot read download the device error, downloading is stopped
download from 0x59 XGT Panel
0x27 data format version. because it doesn’t know the version. If this
USB storage
symptom is repeated, contact Customer
device
Service Center.
Download data format
version is not matched. Data storage type is not correct. Update XGT
0x5A XGT Panel
Please update XGT Panel.
Panel.
Download data format
version is not matched. Data storage type is not correct. Update the
0x5A XGT Panel
Please update XP- XP-Builder.
Builder.
There is no project data file at designated
location. Check the connection status of USB
0x5B XGT Panel Data file path is invalid.
and if there is no error, save the project to
USB again.

App.1-15
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location
The name of project data file is not saved
Download file name correctly. Save the project at the USB again. If
0x5C XGT Panel
length is invalid. this symptom is repeated, contact Customer
Service Center.

The project data file can’t be found. Save the

Cannot find download project data file at the USB again. When this
0x5D XGT Panel
file. symptom is repeated, check the USB. If there
is no error, contact Customer Service Center.
The project data file is not saved correctly.
Save the project data file at the USB again.
Download file size is
0x5E XGT Panel When this symptom is repeated, check the
invalid.
USB. If there is no error, contact Customer
Service Center.
The project backup file which should be
Cannot find project
0x5F XGT Panel downloaded is not downloaded because of
backup file.
communication error. Download again.
The project backup file is saved incorrectly.
Save the project at the USB storage
Project backup file size is equipment again. When this symptom is
0x60 XGT Panel
invalid. repeated, check the USB storage equipment
and if the USB is normal, contact Customer
Service Center.
The font file’s name is saved incorrectly. Save
Font file name length is the project in the USB again. If this symptom
0x61 XGT Panel
invalid. is repeated, contact Customer Service
Center.
The font file which is needed for project is not
Project
Font file is not saved in the USB storage equipment. Save
download from 0x62 XGT Panel
0x27 downloaded. the project in the USB. If this symptom is
USB storage
repeated, contact Customer Service Center.
device
The font file is not saved correctly. Save the
project at the USB. Save the project at the
0x63 XGT Panel Font file size is invalid. USB. If this symptom is repeated, check the
USB and if the USB is normal, contact
Customer Service Center.
The data can’t be analyzed because the
project data file is not saved correctly. Save
Cannot unmarshall
0x64 XGT Panel the project at the USB again. If this symptom
download file.
is repeated, check the USB and if the USB is
normal, contact Customer Service Center.
The data of the project can’t be deleted
Cannot delete previous because of device error. If this symptom is
0x65 XGT Panel
project data. repeated, check the USB and if the USB is
normal, contact Customer Service Center.

App.1-16
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location
Downloaded font file is moved to the original
Cannot move new font storage location. But when it fails, the
0x66 XGT Panel
files. downloading is stopped. If this symptom is
repeated, contact Customer Service Center.
The project data classified according to the
content is moved to the original storage
Cannot move new location. But when it fails, the downloading is
0x67 XGT Panel
project data files. stopped. If this symptom is repeated, contact
Customer Service Center.

The downloaded project zip data is moved to

Cannot move project the original storage location. But when it fails,
0x68 XGT Panel
backup file. the downloading is stopped. If this symptom is
repeated, contact Customer Service Center.

XGT Panel software was already started.

Previous instance is not
0x01 XGT Panel Reboot the device. If this symptom is
terminated.
repeated, contact Customer Service Center.

The XGT Panel software can’t initialize the

communication status normally. Check the
Start Server Fail. Restart
0x02 XGT Panel communication status again. If this symptom
XGT Panel
is repeated when communication is normal,
contact Customer Service Center.
XGT Panel
0x28 The XGT Panel software can’t initialize the
booting
communication status normally. Check the
Failed to Start Echo
0x03 XGT Panel communication status again. If this symptom
Server.
is repeated when communication is normal,
contact Customer Service Center.

The XGT Panel software can’t initialize the

communication with the XP-Builder normally.
Failed to accept
0x04 XGT Panel Check the communication status again. If this
connection.
symptom is repeated when communication is
normal, contact Customer Service Center.

App.1-17
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location

In the present XGT Panel the new updated

XGT Panel software’s name can not be
changed.
After rebooting the XGT Panel, update again.
When rebooting, if you can’t start engine,
Failed to rename
0x05 XGT Panel delete
UpdateNew.exe
\\FlashDisk\LSISProduct\UpdateNew.exe in
the XGT Panel. Then if you touch Update.exe
and execute the XGT Panel, it can be update
mode. Try update again. If this symptom is
repeated, contact Customer Service Center

The new module is downloaded by the XGT

Panel update but the previous module is not
deleted. Reboot the device. If the XGT Panel
software is not started normally, touch
Failed to Delete
0x06 XGT Panel \\FlashDisk\LSISProduct\Update.exe in the
Update.exe.
XGT Panel. At this time, if XGT is set as
update mode, update again. If this symptom
is repeated, contact Customer Service
Center.
The device connection password can’t be
modified because of error of Flash Disk of
Failed to modify
0x30 XGT Panel XGT Panel. Reboot the device. If this
password file.
symptom is repeated, contact Customer
Service Center.
It failed to set and modify password because
Password-related
of communication status error. If this symptom
0x31 XGT Panel command transmission
is repeated, contact Customer Service
Communicatio payload error
Center.
n between
other XP 0x29 There is no XGT Panel The connection setting file of XGT Panel can’t
Builder- 0x32 XGT Panel
connection setting file. be found.
XGT Panel
The modified information can’t be saved at
Modified content can’t be
the connection setting file of XGT Panel. If this
0x33 XGT Panel saved in the XGT Panel
symptom is repeated, contact Customer
connection setting file.
Service Center.
The XGT Panel’s time can’t be set. If this
0x34 XGT Panel Failed to set the time symptom is repeated, contact Customer
Service Center.
Because the each module version information
XGT Failed to Create
XGT panel can’t be read because of XGT Panel’s error, it
0x30 0x21 Panel/ Initialized Module
S/W update failed to initialize. If this symptom is repeated,
XP-Builder Version File.
contact Customer Service Center.

App.1-18
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location
The each module version information can’t be
XGT
Module version file size read because of XGT Panel’s error. If this
0x22 Panel/
is invalid. symptom is repeated, contact Customer
XP-Builder
Service Center.
The each module version information can’t be
XGT
Can't Read module read because of XGT Panel’s error. If this
0x23 Panel/
version file. symptom is repeated, contact Customer
XP-Builder
Service Center.
The version information list to update is
empty. Check the module folder newly
designated at XP-
There's no file to
0x24 XP-Builder Builder and if there is no error, download XGT
download.
Panel module and try update again. If this
symptom is repeated, contact Customer
Service Center.
The wrong file which is not in the new module
Downloaded file is not list of XGT Panel is downloaded. Try update
0x25 XP-Builder
Module to download. of XGT Panel again. If this symptom is
repeated, contact Customer Service Center.

The space to copy new module in XGT Panel

is not enough. After deleting the unnecessary
Not enough space in file or backing up the previous file to the
0x26 XGT Panel
flash memory. movable storage equipment, try update again.
If this symptom is repeated after deleting,
contact Customer Service Center.

The new module is not installed because of

XGT Panel’s error. After rebooting the device,
XGT panel Failed to Copy module touch \\FlashDisk\LSISProduct\Update.exe
0x30 0x27 XGT Panel
S/W update ~.dll and set the device as update mode. Then
update again. If this symptom is repeated,
contact Customer Service Center.

To reboot the engine is not available because

of wrong file which is developed by
downloading wrong module or
Failed to Start Engine.
communication error.
0x28 XGT Panel Please update engine
Touch \\FlashDisk\LSISProduct\Update.exe
again.
and set the device as update mode. Then
update again. If this symptom is repeated,
contact Customer Service Center.

App.1-19
 Appendix 1. Troubleshooting

Error code Occurrence

Object Error message Reason and measure
Type Address location

It is failed to record the version information

Failed to write Data to during update of XGT Panel. If this symptom
0x2A XGT Panel
Module version File. is repeated, contact Customer Service
Center.
To reboot the engine is not available because
of wrong file which is developed by
downloading wrong module or
There's no downloaded communication error.
0x2B XGT Panel
file. Touch \\FlashDisk\LSISProduct\Update.exe
and set the device as update mode. Then
update again. If this symptom is repeated,
contact Customer Service Center.
To reboot the engine is not available because
of wrong file which is developed by
(improper
downloading wrong module or
communication
communication error.
0x2C XGT Panel command)
Touch \\FlashDisk\LSISProduct\Update.exe
Current state is not
and set the device as update mode. Then
authorized.
update again. If this symptom is repeated,
contact Customer Service Center.
To reboot the engine is not available because
of wrong file which is developed by
(improper
downloading wrong module or
communication
communication error.
0x2D XGT Panel command)
Touch \\FlashDisk\LSISProduct\Update.exe
A module to download is
and set the device as update mode. Then
not listed up yet.
update again. If this symptom is repeated,
contact Customer Service Center.
XGT can’t be set as update mode because of
XGT panel
0x30 XGT Panel error. After downloading new XGT
S/W update
Panel module through homepage, etc., copy
UpdateNew.exe file among new module to
the \\FlashDisk\LSISProduct\ directory of XGT
Failed to Initialize Update
0x2E XGT Panel Panel through the movable storage
program.
equipment. Then reboot the XGT Panel and
go update mode and update again. If this
symptom is repeated, contact Customer
Service Center.

App.1-20
 Appendix 2. Dimension

Appendix 2. Dimension (Unit: mm)

(1) iXP70-TTA/AC (DC)

App.2-1
 Appendix 2. Dimension

(2) iXP80-TTA/AC (DC)

App.2-2
 Appendix 2. Dimension

(3) iXP90-TTA/AC (DC)

App.2-3
 Warranty and Environmental Policy

Warranty

1. Warranty Period
The product you purchased will be guaranteed for 18 months from the date of manufacturing.

2. Scope of Warranty
Any trouble or defect occurring for the above-mentioned period will be partially replaced or repaired. However, please
note the following cases will be excluded from the scope of warranty.

Any trouble attributable to unreasonable condition, environment or handling otherwise specified in the manual,
Any trouble attributable to others’ products,
If the product is modified or repaired in any other place not designated by the company,
Due to unintended purposes
Owing to the reasons unexpected at the level of the contemporary science and technology when delivered.
Not attributable to the company; for instance, natural disasters or fire

3. Since the above warranty is limited to HMI unit only, make sure to use the product considering the safety for system
configuration or applications.

Environmental Policy

LS Industrial Systems Co., Ltd supports and observes the environmental policy as below.

Environmental Management About Disposal

LS Industrial Systems considers the LS Industrial Systems’ PLC unit is designed

environmental preservation as the preferential to protect the environment. For the disposal,
management subject and every staff of LS separate aluminum, iron and synthetic resin
Industrial Systems use the reasonable (cover) from the product as they are
endeavors for the pleasurably environmental reusable.
preservation of the earth.
 LS values every single customers.
Quality and service come first at LSIS.
Always at your service, standing for our customers.

www.lsis.com

10310001277

■ HEAD OFFICE ■ LSIS Chengdu Office _ Chengdu, China

LS tower, Hogye-dong, Dongan-gu, Anyang-si, Gyeonggi-do 1026-6, Address : 12FL. Guodong Buiding. No.52 Jindun
Korea http://www.lsis.com Road Chengdu.610041. P.R. China
Tel : (82-2)2034-4870/Fax : 82-2-2034-4648 e-mail : cshwang@lsis.com Tel : 86-28-8612-9151(9226)/Fax : 86-28-8612-9236 e-mail : comysb@lsis.com
■ LSIS Tokyo Office _ Tokyo, Japan ■ LSIS Qingdao Office _ Qingdao, China
Address: 16FL. Higashi-Kan. Akasaka Twin Tower 17-22, Address : YinHe Bldg. 402 Room No. 2P Shandong Road,
Akasaka.Monato-ku Tokyo 107-8470. Japan Qingdao-City,Shandong-province 266071, P.R. China
Tel : 81-3-3582-9128/Fax : 81-3-3582-2667 e-mail : jschuna@lsis.com Tel : 86-532-8501-6068/Fax : 86-532-8501-6057 e-mail : wangzy@lsis.com.cn
■ LSIS(ME) FZE _ Dubai, U.A.E. ■ LSIS Europe B.V.
Address : Jafza View Tower Lob 19, Room 205 Along Sheikh Zayed Address : 1st. Floor, Tupolevlaan 48, 1119NZ, Schiphol-Rijk, The Netherlands
Road Jebel Aali Free Zone Dubai, United Arab Emirates Tel : +31 (0)20 654 1420/Fax : +31 (0)20 654 1429 e-mail : junshickp@lsis.com
Tel : 971-4-886-5360/Fax : 971-4-886-5361 e-mail : jungyongl@lsis.com ■ LSIS(Wuxi) Co., Ltd _ Wuxi, China
■ LSIS Shanghai Office _ Shanghai, China Address : 102-A. National High & New Tech Industrial Development Area.
Address : Room E-G. 12FL Hiamin Empire Plaza. No.726. West. Wuxi. Jiangsu. 214028. P.R. China
Yan'an Road Shanghai 200050. P.R. China e-mail : liyong@lsis.com.cn Tel : 86-510-8534-6666/Fax : 86-510-8534-4078 e-mail : caidx@lsis.com.cn
Tel : 86-21-5237-9977(609)/Fax : 89-21-5237-7189 ■ LSIS(Dalian) Co., Ltd. _ Dalian, China
■ LSIS Beijing Office _ Beijing, China Address : No. 15. Liaohexi 3-Road. Economic and Technical Development zone.
Address : B-Tower 17FL. Beijing Global Trade Center B/D. No. 36. Dalian 116600. China
East BeisanHuan-Road. DongCheng-District. Beijing 100013. P.R. China Tel : 86-411-273-7777/Fax : 86-411-8730-7560 e-mail : cuibx@lsis.com.cn
Tel : 86-10-5825-6027(666)/Fax : 86-10-5825-6028 e-mail : xunmj@lsis.com.cn
■ LSIS Guangzhou Office _ Guangzhou, China
Address : Room 1403.14FL. New Poly Tower.
2 Zhongshan Liu Road.Guangzhou.P.R China
Tel : 86-20-8328-6754/Fax : 86-20-8326-6287 e-mail : chenxs@lsis.com.cn

※ LS Industrial Systems constantly endeavors to improve its product so that 2013. 11

information in this manual is subject to change without notice.
ⓒ LSIS Co., Ltd 2013 All Rights Reserved.