Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #1: Constructional Geometry
Draw the following using scale 1:1 (Dimensions are in mm):
Exercise (1- a)
Exercise (1-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #2: Constructional Geometry
Draw the following using scale 1:1 (Dimensions are in millimeter):
Exercise (2-a)
Exercise (2-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #3: Orthographic Projection
Draw the three orthographic views for the following (use scale 1:1)
Note: All dimensions are in millimeter:
50
40
50
80
40
80
0
13
0 15
Exercise (3-a)
40
30
30 50
80
120
40
30
0
15
90
Exercise (3-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #4 : Orthographic Projection
Draw the three orthographic views for the following (use scale 1:1)
Note: All dimensions are in millimeter:
Exercise (4-a)
Exercise (4-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #5 : Orthographic Projection
Draw the three orthographic views for the following (use scale 1:1)
Note: All dimensions are in millimeter:
Exercise (5-a)
Exercise (5-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #6 : Orthographic Projection
Draw the three orthographic views for the following (use scale 1:1)
Note: All dimensions are in millimeter:
Exercise (6-a)
Exercise (6-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #7 : Orthographic Projection and Writing dimensions
Draw the three orthographic views for the following (use scale 1:1)
Note: All dimensions are in millimeter:
Exercise (7-a)
Exercise (7-b)
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #8 : Sectional Views
For the isometrics shown below, draw the following:
a- Sectional Front view at the middle of the part drawing.
b- Sectional Side view at the middle of the part drawing.
c- Complete Top view
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #9: Sectional Views
For the isometrics shown below, draw the following:
a- Sectional Front view at the middle of the part drawing.
b- Complete Side view.
c- Complete Top view
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #9: Sectional Views
For the isometrics shown below, draw the following:
a- Sectional Front view at the middle of the part drawing.
b- Complete Side view.
c- Complete Top view
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #10: Isometric Drawing
For the two orthographic views shown at right, do the following:
a) Draw the corresponding Isometric using the same isometric view
shown at right.
b) Write all dimensions on the Isometric.
Notes:
1. All dimensions are in mm.
2. Assume any missed dimensions.
35 46
60
20
30
108
Top View
51
36
60
24
40
12
90
Front View
Kingdom of Saudi Arabia المملكة العربية السعودية
Ministry of Higher Education وزارة التعليم العالي
Qassim University جامعـة القصيـم
Faculty of Engineering كليه الهندسه
Mechanical Engineering Dept.
Basics of Engineering Graphics (GE 104)
Sheet #11: Isometric Drawing
For the two orthographic views shown at right, do the following:
a) Draw the corresponding Isometric using the same isometric view
shown at right.
b) Write all dimensions on the Isometric.
Notes:
1. All dimensions are in mm.
2. Assume any missed dimensions.
10 20
15
20
30 10
70
20
6
10
80 40
Front View Side View
