HA-5112/883

Dual, Low Noise, High Performance

July 1994 Uncompensated Operational Amplifier

Features Description
• This Circuit is Processed in Accordance to MIL-STD- Low Noise and high performance are key words describing
883 and is Fully Conformant Under the Provisions of the dual, uncompensated HA-5112/883. This general pur-
Paragraph 1.2.1. pose amplifier offers an array of dynamic specifications
including 12V/µs slew rate (min), and 54MHz gain-band-
• Low Input Noise Voltage Density at 1kHz. . . 6nV/√Hz(Max)
width-product for AVCL ≥ 10. Complementing these outstand-
4.3nV/√Hz(Typ)
ing parameters is a very low noise specification of 6nV/√Hz
• High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 12V/µs (Min) at 1kHz (max).
20V/µs (Typ)
Fabricated using the Intersil standard high frequency D.I.
• Wide Gain Bandwidth Product (AVCL ≥ 10) . . . . 54MHz process, these operational amplifiers also offer excellent
input specifications such as 2.5mV (max) offset voltage and
• Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ) 75nA (max) offset current. Complementing these specifica-
• High Open Loop Gain (Full Temp.). . . . . 100kV/V (Min) tions are 100dB (min) open loop gain and 55dB channel
250kV/V (Typ) separation (min). The HA-5112/883 also consumes a very
modest amount of supply power (180mW/package).
• High CMRR/PSRR (Full Temp.) . . . . . . . . . . . 86dB (Min)
100dB (Typ) This impressive combination of features make this amplifier
ideally suited for designs ranging from audio amplifiers and
• Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ) active filters to the most demanding signal conditioning and
• No Crossover Distortion instrumentation circuits.

• Standard Dual Pinout

Ordering Information
Applications
PART TEMPERATURE
• High Quality Audio Preamplifiers NUMBER RANGE PACKAGE

• High Q Active Filters HA2-5112/883 -55oC to +125oC 8 Pin Can

• Low Noise Function Generators
HA4-5112/883 -55oC to +125oC 20 Lead Ceramic LCC
• Low Distortion Oscillators
HA7-5112/883 -55oC to +125oC 8 Lead CerDIP
• Low Noise Comparators

Pinouts
HA-5112/883 HA-5112/883 HA-5112/883
(CERDIP) (CLCC) (METAL CAN)
TOP VIEW TOP VIEW TOP VIEW
OUT 1

V+
NC

NC

NC
V+

OUT1 1 8 V+ 8
3 2 1 20 19
OUT1 1 7 OUT2
-IN1 2 7 OUT2 18 NC 1 2
1 NC 4 1
- -+
-IN1 5 17 OUT2 - + + -
+IN1 3 + 6 -IN2 2 -IN1 2 6 -IN2
2
- NC 6 +- 16 NC
V- 4 + 5 +IN2 +IN1 7 15 -IN2
+IN1 3 5 +IN2
NC 8 14 NC
4
9 10 11 12 13 V-
V-
NC

NC
+IN2

NC

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. Spec Number 511032-883
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
3-119 File Number 3711
 Specifications HA-5112/883

Absolute Maximum Ratings Thermal Information

Voltage between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Thermal Resistance θJA θJC
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W 28oC/W
Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to V- Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W
Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite Metal Can Package . . . . . . . . . . . . . . . . . 155oC/W 67oC/W
(One Amplifier Shorted to Ground) Package Power Dissipation Limit at +75oC
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645mW
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC Package Power Dissipation Derating Factor Above +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC
Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5mW/oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Operating Conditions
Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC VINCM ≤ 1/2 (V+ - V-)
Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V RL ≥ 2kΩ

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS

Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.

LIMITS
GROUP A
PARAMETERS SYMBOL CONDITIONS SUBGROUPS TEMPERATURE MIN MAX UNITS

Input Offset Voltage VIO VCM = 0V 1 +25oC -2.0 2.0 mV

2, 3 +125oC, -55oC -2.5 2.5 mV

Input Bias Current +IB VCM = 0V, +RS = 10kΩ, 1 +25oC -200 200 nA
-RS = 100Ω
2, 3 +125oC, -55oC -325 325 nA

-IB VCM = 0V, +RS = 100Ω, 1 +25oC -200 200 nA

-RS = 10kΩ
2, 3 +125oC, -55oC -325 325 nA

Input Offset Current IIO VCM = 0V, 1 +25oC -75 75 nA

+RS = 10kΩ,
2, 3 +125oC, -55oC -125 125 nA
-RS = 10kΩ

Common Mode Range +CMR V+ = +3V, V- = -27V 1 +25oC +12 - V

2, 3 +125oC, -55oC +12 - V

-CMR V+ = +27V, V- = -3V 1 +25oC - -12 V

2, 3 +125oC, -55oC - -12 V

Large Signal Voltage +AVOL VOUT = 0V and +10V, 4 +25oC 100 - kV/V
Gain RL = 2kΩ
5, 6 +125oC, -55oC 100 - kV/V

-AVOL VOUT = 0V and -10V, 4 +25oC 100 - kV/V

RL = 2kΩ
5, 6 +125oC, -55oC 100 - kV/V

Common Mode +CMRR ∆VCM = +5V, 1 +25oC 86 - dB

Rejection Ratio V+ = +10V, V- = -20V,
2, 3 +125oC, -55oC 86 - dB
VOUT = -5V

-CMRR ∆VCM = -5V, 1 +25oC 86 - dB

V+ = +20V, V- = -10V,
2, 3 +125oC, -55oC 86 - dB
VOUT = +5V

Spec Number 511032-883

3-120
 Specifications HA-5112/883

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)

Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.

LIMITS
GROUP A
PARAMETERS SYMBOL CONDITIONS SUBGROUPS TEMPERATURE MIN MAX UNITS

Output Voltage Swing +VOUT1 RL = 2kΩ 1 +25oC 10 - V

2, 3 +125oC, -55oC 10 - V

-VOUT1 RL = 2kΩ 1 +25oC - -10 V

2, 3 +125oC, -55oC - -10 V

+VOUT2 RL = 10kΩ 1 +25oC 12 - V

2, 3 +125oC, -55oC 12 - V

-VOUT2 RL = 10kΩ 1 +25oC - -12 V

2, 3 +125oC, -55oC - -12 V

Output Current +IOUT VOUT = -5V 1 +25oC 10 - mA

2, 3 +125oC, -55oC 10 - mA

-IOUT VOUT = +5V 1 +25oC - -10 mA

2, 3 +125oC, -55oC - -10 mA

Quiescent Power Supply +ICC VOUT = 0V, IOUT = 0mA 1 +25oC - 5 mA

Current
2, 3 +125oC, -55oC - 6 mA

-ICC VOUT = 0V, IOUT = 0mA 1 +25oC -5 - mA

2, 3 +125oC, -55oC -6 - mA

Power Supply +PSRR ∆VSUP = 10V, 1 +25oC 86 - dB

Rejection Ratio V+ = +10V, V- = -15V
2, 3 +125oC, -55oC 86 - dB
V+ = +20V, V- = -15V

-PSRR ∆VSUP = 10V, 1 +25oC 86 - dB

V+ = +15V, V- = -10V
2, 3 +125oC, -55oC 86 - dB
V+ = +15V, V- = -20V

TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS

Table 2 Intentionally Left Blank. See AC Parameters in Table 3

TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS

Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 10V/V, Unless Otherwise Specified.

LIMITS
PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS
Differential Input RIN VCM = 0V 1 +25oC 250 - kΩ
Resistance
Input Noise Voltage EN RS = 20Ω, 1 +25oC - 6 nV/√Hz
fO = 1000Hz
Input Noise Current IN RS = 2MΩ, 1 +25oC - 3 pA/√Hz
fO = 1000Hz
Gain Bandwidth Product GBWP VO = 200mV, 1 +25oC 40 - MHz
fO = 50kHz
VO = 200mV, 1 +25oC 54 - MHz
fO = 1MHz

Spec Number 511032-883

3-121
 Specifications HA-5112/883

TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)

Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 10V/V, Unless Otherwise Specified.

LIMITS
PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS
Slew Rate +SR VOUT = -5V to +5V 1 +25oC 12 - V/µs
-SR VOUT = +5V to -5V 1 +25oC 12 - V/µs
Full Power Bandwidth FPBW VPEAK = 10V 1, 2 +25oC 191 - kHz
Minimum Closed Loop CLSG RL = 2kΩ, CL = 50pF 1 -55oC to +125oC 10 - V/V
Stable Gain
Rise and Fall Time tR VOUT = 0V to +200mV 1, 4 +25oC - 100 ns
tF VOUT = 0V to -200mV 1, 4 +25oC - 100 ns
Overshoot +OS VOUT = 0V to +200mV 1 +25oC - 40 %
-OS VOUT = OV to -200mV 1 +25oC - 40 %
Output Resistance ROUT Open Loop 1 +25oC - 232 Ω
Quiescent Power PC VOUT = 0V, IOUT = 0mA 1, 3 -55oC to +125oC - 180 mW
Consumption
Channel Separation CS RS = 1kΩ, 1 +25oC 55 - dB
AVCL = 100V/V,
VIN = 100mVPEAK at
10kHz, Referred to
Input
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These param-
eters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK).
3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.).
4. Measured between 10% and 90% points.

TABLE 4. ELECTRICAL TEST REQUIREMENTS

MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLE 1)

Interim Electrical Parameters (Pre Burn-In) 1

Final Electrical Test Parameters 1 (Note 1), 2, 3, 4, 5, 6

Group A Test Requirements 1, 2, 3, 4, 5, 6

Groups C and D Endpoints 1

NOTE:
1. PDA applies to Subgroup 1 only.

Spec Number 511032-883

3-122
 HA-5112/883

Die Characteristics
DIE DIMENSIONS:
98.4 x 67.3 x 19 mils ± 1 mils
2500 x 1710 x 483µm ± 25.4µm
METALLIZATION:
Type: Al, 1% Cu
Thickness: 16kÅ ± 2kÅ
GLASSIVATION:
Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.)
Silox Thickness: 12kÅ ± 2kÅ
Nitride Thickness: 3.5kÅ ± 1.5kÅ
WORST CASE CURRENT DENSITY:
1.43 x 105A/cm2 at 10mA
SUBSTRATE POTENTIAL (Powered Up):
Unbiased
TRANSISTOR COUNT: 93
PROCESS: Bipolar Dielectric Isolation

Metallization Mask Layout

HA-5112/883

V- +IN1 -IN1 OUT1

+IN2 -IN2 OUT2 V+

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com

Spec Number 511032-883

3-123