Process Equipment Catalog

Pumping Solutions for Process Industries

 Table of Contents
Process Equipment Buyer’s Guide

Contents
Air-Operated Double Diaphragm Pumps Model Overview............................ 2
Pump Selection Key for Husky™ AODD Pumps............................................ 4
Husky 205 Plastic Pumps........................................................................... 7
Husky 307 Plastic Pumps........................................................................... 9
Husky 515 Plastic Pumps......................................................................... 12
Husky 716 Metal Pumps........................................................................... 15
Husky 1050 Plastic Pumps....................................................................... 18
Husky 1050 Metal Pumps......................................................................... 21
Husky 1590 Plastic Pumps....................................................................... 25
Husky 1590 Metal Pumps......................................................................... 28
Husky 2150 Plastic Pumps....................................................................... 31
Husky 2150 Metal Pumps......................................................................... 34
Husky 3300 Plastic Pumps....................................................................... 37
Husky 3300 Metal Pumps......................................................................... 41
Husky Transfer Pump Packages................................................................ 44
Husky Transfer Pump and Agitator Packages............................................. 47
Husky Pump Accessories.......................................................................... 48
EP Series Hose Pumps.............................................................................. 53
Hydra-Clean®............................................................................................ 61
CycleFlo™ and CycleFlo II.......................................................................... 64
Fast-Flo® 1:1............................................................................................ 66
Piston Pumps for Ink Applications............................................................. 67
Surge Suppressors................................................................................... 71

1
process equipment catalog
 Air-Operated Double Diaphragm Pumps
Model Overview

Model Husky™ 205 Husky 307 Husky 515 Husky 716 Husky 1050 Husky 1050
Plastic Plastic Plastic Metal Plastic Metal
Connection 1/4 in 3/8 in 1/2 in 3/4 in 1 in 1 in
Size (6.3 mm) (9.4 mm) (12.7 mm) (19.1 mm) (25.4 mm) (25.4 mm)
Thread Type NPT or BSP NPT or BSP NPT or BSP NPT or BSP ANSI/DIN Flange NPT or BSP

Air Valve Standard and Standard Standard and Standard and Standard, Smart Standard, Smart
Remote Remote Remote and Remote and Remote
Maximum 5 gpm 7 gpm 15 gpm 16 gpm 50 gpm 50 gpm
Flow Rate (19 lpm) (26 lpm) (57 lpm) (61 lpm) (189 lpm) (189 lpm)
Maximum 100 psi 100 psi 100 psi 100 psi 125 psi 125 psi
Discharge (7 bar, 0.7 MPa) (7 bar, 0.7 MPa) (7 bar, 0.7 MPa) (7 bar, 0.7 MPa) (8.6 bar. 0.9 MPa) (8.6 bar, 0.9 MPa)
Pressure
Materials of Polypropylene, Polypropylene, Polypropylene, Aluminum, 316 Polypropylene, Aluminum, 316
Construction PVDF, Acetal Acetal PVDF, Acetal Stainless Steel Conductive Poly, Stainless Steel,
Available PVDF Hastelloy
Center Section Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene, Coated Aluminum,
Available Conductive Poly Polypropylene,
Conductive Poly
Pump Weight 2.0 lb (0.9 kg) 4.75 lb (2.2 kg) 6.5 lb (2.9 kg) 8.5 lb (3.9 kg) 18 lb (8.2 kg) 23 lb (10.4 kg)
Polypropylene Polypropylene Polypropylene Aluminum Polypropylene Aluminum
2.5 lb (1.1 kg) 5.2 lb (2.4 kg) 7.8 lb (3.5 kg) 18 lb (8.2 kg) 26 lb (11.8 kg) 36.3 - 41 lb
Acetal Acetal Acetal Stainless Steel PVDF (16.5-18.6 kg)
Stainless Steel
2.8 lb (1.3 kg) 8.5 lb (3.9 kg) 41 lb (18.6 kg)
PVDF PVDF Hastelloy
Maximum 0.06 in 0.063 in 0.094 in 0.094 in 0.125 in 0.125 in
Solids (1.5 mm) (1.6 mm) (2.5 mm) (2.5 mm) (3.2 mm) (3.2 mm)

2
process equipment catalog
Husky 1590 Husky 1590 Husky 2150 Husky 2150 Husky 3300 Husky 3300
Plastic Metal Plastic Metal Plastic Metal
1-1/2 in 1-1/2 in 2 in 2 in 3 in 3 in
(38.1 mm) (38.1 mm) (50.8 mm) (50.8 mm) (76.2 mm) (76.2 mm)
ANSI Flange NPT or BSP ANSI Flange NPT or BSP DIN/ANSI NPT and BSP
DIN/ANSI (AL only)
Standard and Standard and Standard and Standard and Standard Standard
Remote Remote Remote Remote
100 gpm 100 gpm 150 gpm 150 gpm 280 gpm 300 gpm
(379 lpm) (379 lpm) (568 lpm) (568 lpm) (1,059 lpm) ** (1,135 lpm) **
120 psi 120 psi 120 psi 120 psi 100 psi 125 psi
(8.3 bar, 0.8 MPa) (8.3 bar, 0.8 MPa) (8.3 bar, 0.8 MPa) (8.3 bar, 0.8 MPa) (7 bar, 0.7 MPa) (8.6 bar, 0.9 MPa)
with AL center
Polypropylene, Aluminum, 316 Polypropylene, Aluminum, 316 Polypropylene Aluminum, 316
PVDF Stainless Steel PVDF Stainless Steel, Stainless Steel
Ductile Iron
Coated Aluminum, Coated Aluminum, Coated Aluminum, Coated Aluminum, Polypropylene Aluminum,
316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel Polypropylene*
(*SST pump only)

35 lb (16 kg) 33.5 lb (15.2 kg) 49 lb (22 kg) 58 lb (26.3 kg) 200 lb (90.7 kg) 150 lb (68 kg)
Polypropylene Aluminum Polypropylene Aluminum Polypropylene Aluminum
49 lb (22 kg) 86 lb (40 kg) 68 lb (31 kg) 111 lb (50.3 kg) 255 lb (115.6 kg)
PVDF Stainless Steel PVDF Stainless Steel Stainless Steel

130 lb (59 kg)

Ductile Iron
0.188 in 0.188 in 0.25 in 0.25 in 0.5 in 0.5 in
(4.8 mm) (4.8 mm) (6.3 mm) (6.3 mm) (12.7 mm) (12.7 mm)
NEW! Husky 3300
3 inch Pump Family

**Maximum flow rate using standard diaphragm at 125 psi (8.6 bar).

3
process equipment catalog
 Pump Selection Key
Husky AODD Pumps

Pump Designation
Part numbers are located on ID tag on center section of all Husky diaphragm pumps.

D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Size Parts Balls/
Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm
1 = 1/4” (6.35 mm) Standard: polypropylene center section 1 = Acetal (npt) 2 = Acetal 1 = PTFE 1 = PTFE
2 = 1/4” (6.35 mm) Remote: polypropylene center section 2 = Poly (npt) 3 = Stainless Steel 2 = Acetal 5 = TPE
3 = 3/8” (9.52 mm) Standard: polypropylene center section 3 = Aluminum (npt) 4 = Hardened SST 3 = Stainless Steel 6 = Santoprene
5 = 1/2” (12.7 mm) Standard: polypropylene center section 4 = Stainless Steel (npt) 5 = TPE 4 = Hardened SST 7 = Buna N
4 = 1/2” (12.7 mm) Remote: polypropylene center section 5 = PVDF (npt) 6 = Santoprene 5 = TPE 8 = Fluoroelastomer
5 = 3/4” (19.05 mm) Standard: polypropylene center section 6 = Ductile Iron (npt) 7 = Buna N 6 = Santoprene G = Geolast
4 = 3/4” (19.05 mm) Remote: polypropylene center section 8 = Fluoroelastomer 7 = Buna N
1” (25.4 mm) refer to Husky Selector Tool, page 5 A = Acetal * (bsp) 9 = Polypropylene 8 = Fluoroelastomer
B = 1-1/2” (38.1 mm) Standard: aluminum center section B = Poly * (bsp) A = PVDF 9 = Polypropylene
C = 1-1/2” (38.1 mm) Remote: aluminum center section C = Aluminum (bsp) G = Geolast A = PVDF
T = 1-1/2” (38.1 mm) Standard: stainless steel center section D = Stainless Steel (bsp) G = Geolast
U = 1-1/2” (38.1 mm) Remote: stainless steel center section E = PVDF (bsp) B = SST with viton seal
F = 2” (50.8 mm) Standard: aluminum center section F = Ductile Iron (bsp) C = Santoprene with
G = 2” (50.8 mm) Remote: aluminum center section viton seal
V = 2” (50.8 mm) Standard: stainless steel center section H = 2 npt Alum Extended
3” (76.2 mm) refer to Husky Selector Tool, page 5 G = 2 bsp Alum Extended




* = BSP plastic in 1/2” (12.7mm) pumps
>1” Plastic pumps flange connections
Note: Above matrix is all possible combinations. All combination may not be available. See specific pump listings for available combinations.

Diaphragm Pump Kit Designation

When selecting a kit, use the same code numbers as for the pumps regarding pump size, seat, ball/checks and diaphragm.

D O X X X X
Diaphragm Pump Balls/
Pump Kit Size Seats Checks Diaphragms

Pump Size Seats Balls/Checks Diaphragm

1 = 1/4 in (6.35 mm) 0 = No seat 1 = PTFE 1 = PTFE
3 = 3/8 in (9.52 mm) 2 = Acetal 2 = Acetal 5 = TPE
5 = 1/2 in (12.7 mm) and 3/4 in (19.05 mm) 3 = Stainless Steel 3 = Stainless Steel 6 = Santoprene
1” (25.4 mm) refer to Husky Selector Tool, 4 = Hardened SST 4 = Hardened SST 7 = Buna-N
page 5 5 = TPE 5 = TPE 8 = Fluoroelastomer
B = 1-1/2 in (38.1 mm) metal pump 6 = Santoprene 6 = Santoprene G = Geolast
C = 1-1/2 in (38.1 mm) plastic pump 7 = Buna N 7 = Buna-N
F = 2 in (50.8 mm) metal pump 8 = Fluoroelastomer 8 = Fluoroelastomer 0 = No Diaphragm
G = 2 in (50.8 mm) plastic pump 9 = Poly 9 = Poly
3 in (76.2 mm) refer to Husky Selector Tool, A = PVDF A = PVDF
page 5 B = SST with viton seal G = Geolast
C = S antoprene with
viton seal 0 = No Balls/Checks
G = Geolast

4
process equipment catalog
 Pump Selection Key

Husky 1050 & 3300 Selector Tool

Find the Right Pump for your Application

To order a Husky 1050 or a Husky 3300, use the online selector tool
at www.graco.com/process or contact your distributor.

From the homepage at www.graco.com/process click on “Online Husky Selector Tool” Example of Product Selector Tool on www.graco.com/process.

Wetted Parts Material Options

Acetal Material used for seats, balls & wetted body parts Buna-N Material used for seats, balls and diaphragms
• Wide range of solvent resistance • Good for petroleum-based fluids
• Withstands extreme fatigue • Not for use with strong solvents or chemicals
• Good level of abrasion resistance • Food grade*
• Groundable for use with flammables
Geolast Material used for seats, balls & diaphragms
• Not for use with acids or bases
• Good abrasion resistance
Aluminum Material used for air motor & wetted body parts • Same chemical compatibility as Buna-N and TPE
• Medium corrosion and abrasion resistance
TPE Material used for seats, balls & diaphragms
• Not for use with halogenated hydrocarbons
• Good abrasion resistance
Ductile Iron Material used for wetted body parts • Often substituted for Buna-N
• High abrasion resistance
Santoprene® Material used for seats, balls & diaphragms
Hardened SST Material used for seats and balls • Good abrasion and chemical resistance
• Moderate chemical resistance • Not for use with solvents or hydrocarbons
• Good abrasion resistance • Often substituted for EPDM or EPR
• Abrasion resistant balls and seats • Food grade*

PVDF Material used for wetted body parts & seats PTFE Material used for balls & diaphragms
• Strong chemical resistance: acids and bases • Excellent when used with solvents
• Good abrasion resistance • Poor abrasion resistance
• High temperature resistance • Widest chemical compatibility with fluids
• Food grade*
Polypropylene Material used for air motor, wetted body parts, seats & balls
• Wide chemical compatibility Fluoroelastomer Material used for seats, balls & diaphragms
• General purpose • High level of corrosion resistance with acids
• Inexpensive alternative • Resists unleaded fuels
• Food grade*
Stainless Steel Material used for air motor, wetted body parts, and seats and balls
• High level of corrosion and abrasion resistance Hastelloy Material used for wetted body parts
• Passivated for use with waterbase coatings • Good resistance to aggressive chemicals and in
corrosive environments
• Compatible with high temperature fluids

*Not recommended for use with Husky 1050 diaphragms

5
process equipment catalog
6
process equipment catalog
 Husky 205 Plastic Pumps
Air-Operated Double Diaphragm

Ordering Information

D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats CHECK VALVES Diaphragm

1 = 1/4” (6.35 mm) Standard: polypropylene center section 1 = Acetal (npt) 0 = No Seats 2 = Acetal 1 = PTFE
2 = 1/4” (6.35 mm) Remote: polypropylene center section 2 = Poly (npt) 9 = Polypropylene 6 = Santoprene

5 = PVDF (npt) A = PVDF

Popular Models
Part Number Part Number
(NPT Ported) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Check Valves Diaphragms Kit Air Kit Control**
Acetal D11021 D21021 D11021 D21021 Acetal PTFE D01021 238853 246946
D11026 D21026 D11026 D21026 Acetal Santoprene D01026 238853 246946
PVDF D150A1 D250A1 D150A1 D250A1 PVDF PTFE D010A1 238853 246946
D150A6 D250A6 D150A6 D250A6 PVDF Santoprene D010A6 238853 246946
Polypropylene D12091 D22091 D12091 D22091 Polypropylene PTFE D01091 238853 246946
D12096 D22096 D12096 D22096 Polypropylene Santoprene D01096 238853 246946
* Requires Cycleflo or external valve control
** Air control includes air regulator and filter with gauge

Technical Specifications
Husky 205 Plastic Pumps Acetal Polypropylene PVDF
Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa)
Maximum free flow delivery* 5.0 gpm (18.9 lpm) 5.0 gpm (18.9 lpm) 5.0 gpm (18.9 lpm)
Maximum pump speed 250 cpm 250 cpm 250 cpm
Displacement per cycle** 0.012 gallon (0.045 liter) 0.012 gallon (0.045 liter) 0.012 gallon (0.045 liter)
Maximum suction lift (D12096) 10 ft (3 m) dry 10 ft (3 m) dry 10 ft (3 m) dry
Maximum size pumpable solids 0.06 in (1.5 mm) 0.06 in (1.5 mm) 0.06 in (1.5 mm)
Maximum operating temperature*** 180°F (82°C) 180°F (82°C) 180°F (82°C)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C) 180°F (82.2°C)
Typical sound level at 70 psi 70 dBa 70 dBa 70 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 9.0 scfm (0.252 m3/min) 9.0 scfm (0.252 m3/min) 9.0 scfm (0.252 m3/min)
Air pressure operating range 20 to 100 psi 20 to 100 psi 20 to 100 psi
(1.4 to 7 bar, 0.14 to 0.7 MPa) (1.4 to 7 bar, 0.14 to 0.7 MPa) (1.4 to 7 bar, 0.14 to 0.7 MPa)
Air inlet size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f)
Air exhaust port size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f)
Fluid inlet & outlet size**** 1/4 npt(f) 1/4 npt(f) 1/4 npt(f)
Weight 2.5 lb (1.1 kg) 2.0 lb (0.9 kg) 2.8 lb (1.3 kg)
Wetted parts Acetal with Stainless Steel fibers, Glass-filled Polypropylene, PVDF, PTFE, Santoprene
(in addition to ball, seat and diaphragm PTFE, Acetal, Santoprene Santoprene, PTFE, Polypropylene
materials– which may vary by pump)
Instruction manual 308652 308652 308652
** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
*** Actual pump performance may be affected by prolonged usage at temperature
**** Hybrid thread allows for either 1/4 npt or 1/4 bspt fitting

7
process equipment catalog
 Husky 205 Plastic Pumps

Performance Charts Dimensions

Husky 205 Performance

120 6
(8, 0.8) (0.17)

100 5
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (0.14)

A

aIr conSumPtIon scfm (m3/min)

80 A 4
(5.5, 0.55) (0.11)
B
60 B 3
(4.1, 0.41) (0.085)

40 2
(2.8, 0.28) (0.057)
C
C
20 1
(1.4, 0.14) (0.028)

6.8 in (173 mm)

0
gpm 0 0.5 1 1.5 2 2.5 3 3.5
(lpm) (1.9) (3.8) (3.8) (7.6) (9.5) (11.4) (13.3)
FluiD FlOW
(Pump tested in water with inlet submerged

aIr PreSSure legenD

A = at 100 psi (7 bar, 0.7 MPa) Air Consumption
B = at 70 psi (4.8 bar, 0.48 MPa) Fluid Flow
C = at 40 psi (2.8 bar, 0.28 MPa)

6 in
(145 mm)

3.7 in
(94 mm)

Typical System Drawings

Husky 205 Wall-Mount with CycleFlo

8
process equipment catalog
 Husky 307 Plastic Pumps
Air-Operated Double Diaphragm

Ordering Information
D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

3 = 3/8” (9.52 mm) Standard: polypropylene center section 1 = Acetal (npt) 2 = Acetal 1 = PTFE 1 = PTFE
2 = Poly (npt) 3 = Stainless Steel 3 = SST 5 = TPE
9 = Polypropylene 5 = TPE 6 = Santoprene
A = Acetal * (bsp) 6 = Santoprene 7 = Buna N
B = Poly * (bsp) 7 = Buna N

Popular Models
Part Number Part Number
(NPT Ported) (BSP Ported)
Standard Remote Standard Remote Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control*
Acetal D31211 NA D3A211 NA Acetal PTFE PTFE D03211 239952 246946
D31255 NA D3A255 NA Acetal TPE TPE D03255 239952 246946
D31277 NA D3A277 NA Acetal Buna Buna D03277 239952 246946
D31311 NA D3A311 NA Stainless Steel PTFE PTFE D03311 239952 246946
Polypropylene D32211 NA D3B211 NA Acetal PTFE PTFE D03211 239952 246946
D32255 NA D3B255 NA Acetal TPE TPE D03255 239952 246946
D32277 NA D3B277 NA Acetal Buna Buna D03277 239952 246946
D32311 NA D3B311 NA Stainless Steel PTFE PTFE D03311 239952 246946
D32366 NA D3B366 NA Stainless Steel Santoprene Santoprene D03366 239952 246946
D32911 NA D3B911 NA Polypropylene PTFE PTFE D03911 239952 246946
D32955 NA D3B955 NA Polypropylene TPE TPE D03955 239952 246946
D32966 NA D3B966 NA Polypropylene Santoprene Santoprene D03966 239952 246946
D32977 NA D3B977 NA Polypropylene Buna Buna D03977 239952 246946
* Air control includes air regulator and filter with gauge

9
process equipment catalog
 Husky 307 Plastic Pumps

Technical Specifications

Husky 307 Plastic Pumps Acetal Polypropylene

Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa)
Maximum free flow delivery* 7.0 gpm (26.5 lpm) 7.0 gpm (26.5 lpm)
Maximum pump speed 330 cpm 330 cpm
Displacement per cycle** 0.02 gallon (0.076 liter) 0.02 gallon (0.076 liter)
Maximum suction lift (D31255) 12 ft (3.7 m) dry 12 ft (3.7 m) dry
Maximum size pumpable solids 0.06 in (1.5 mm) 0.06 in (1.5 mm)
Maximum operating temperature*** 150°F (65.5°C) 150°F (65.5°C)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C)
Buna-N 180°F (82.2°C) 180°F (82.2°C)
TPE 150°F (65.5°C) 150°F (65.5°C)
Typical sound level at 50 psi 75 dBa 75 dBa
(3.5 bar, 0.35 MPa) air @ 50 cpm
Maximum air consumption 6 scfm (0.17 m3/min) 6 scfm (0.17 m3/min)
Air pressure operating range 20 to 100 psi 20 to 100 psi
(1.4 to 8.4 bar, 0.14 to 0.84 MPa) (1.4 to 8.4 bar, 0.14 to 0.84 MPa)
Air inlet size 1/4 npt(f) or bspt(f) 1/4 npt(f) or bspt(f)
Fluid inlet & outlet size**** 3/8 npt(f) 3/8 npt(f)
Weight 5.2 lb (2.4 kg) 4.75 lb (2.2 kg)
Wetted parts (in addition to ball, seat and Acetal with Stainless Polypropylene, PTFE
diaphragm materials–which may vary by pump) Steel fibers, PTFE
Instruction manual 308553 308553
*Flow rates are with muffler and do not vary based on diaphragm material
**Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
***Actual pump performance may be affected by prolonged usage at temperature

Performance Chart

Husky 307 Performance

120 6
(8.4, 0.84) (0.17)

100 5
A
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) A (0.14)

aIr conSumPtIon scfm (m3/min

80 B 4
(5.5, 0.55) (0.11)
B C
60 3
(4.1, 0.41) (0.085)

40 2
(2.8, 0.28) C D (0.057)

20 1
(1.4, 0.14) (0.028)
D
0
gpm 0 1 2 3 4 5 6 7 8
(lpm) (3.8) (7.6) (11.4) (15.2) (19.0) (22.7) (26.5) (30.0)
FluiD FlOW
(Pump tested in water with inlet submerged

aIr PreSSure legenD

A = at 100 psi (7 bar, 0.7 MPa) Air Consumption
B = at 70 psi (4.8 bar, 0.48 MPa) Fluid Flow
C = at 40 psi (2.8 bar, 0.28 MPa)
D = at 20 psi (1.4 bar, 0.14 MPa)

10
process equipment catalog
 Husky 307 Plastic Pumps

Dimensions

3.14 in 4.98 in
(80 mm) (126.5 mm) 2.53 in
(64.5 mm)
1/4 npt(f) Fluid Outlet:
Air Inlet 3/8 npt(f)

8.13 in
(206.5 mm)
6.18 in
(157 mm)
6.05 in
7.24 in
(153.55 mm)
(184 mm)

0.66 in
(17 mm) Fluid Inlet:
3/8 npt(f)
3/8 npt(f) 6.3 in (160 mm)
1.06 in
Air Exhaust (2.7 mm)
8.12 in (206.5 mm) 3.5 in (89 mm)
(muffler included)

5.3 in (134.5 mm)

Typical System Drawings

Husky 307 Wall-Mount with Siphon Feed Husky 307 Drum-Mount with Siphon Feed

Air Control Kit

11
process equipment catalog
 Husky 515 Plastic Pumps
Air-Operated Double Diaphragm

Ordering Information

D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

5 = 1 /2” center (12.7 mm) or 3/4” ends (19.05) 1 = Acetal (npt) 2 = Acetal 1 = PTFE 1 = PTFE
Standard: polypropylene center section
4 = 1 /2” center (12.7 mm) or 3/4” ends (19.05) 2 = Poly (npt) 3 = Stainless Steel 3 = Stainless Steel 5 = TPE
Remote: polypropylene center section
5 = PVDF (npt) 9 = Polypropylene 5 = TPE 6 = Santoprene
A = Acetal * (bsp) A = PVDF 6 = Santoprene 7 = Buna N
B = Poly * (bsp) D = Urethane Duckbill 7 = Buna N 8 = Fluoroelastomer
E = PVDF (bsp) 8 = Fluoroelastomer
* = BSP plastic in 1/2” (12.7 mm) pumps
0 = Duckbill

Popular Models

Part Number Part Number

(NPT Ported) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control**
Acetal D51211 D41211 D5A211 D4A211 Acetal PTFE PTFE D05211 241657 246946
D51255 D41255 D5A255 D4A255 Acetal TPE TPE D05255 241657 246946
D51277 D41277 D5A277 D4A277 Acetal Buna Buna D05277 241657 246946
D51311 D41311 D5A311 D4A311 Stainless Steel PTFE PTFE D05311 241657 246946
D51331 D41331 D5A331 D4A331 Stainless Steel Stainless Steel PTFE D05331 241657 246946
D51D05 D41D05 D5AD05 D4AD05 Duckbill TPE D05D05 241657 246946
D51D06 D41D06 D5AD06 D4AD06 Duckbill Santoprene D05D06 241657 246946
D51D07 D41D07 D5AD07 D4AD07 Duckbill Buna D05D07 241657 246946
Polypropylene D52211 D42211 D5B211 D4B211 Acetal PTFE PTFE D05211 241657 246946
D52277 D42277 D5B277 D4B277 Acetal Buna Buna D05277 241657 246946
D52311 D42311 D5B311 D4B311 Stainless Steel PTFE PTFE D05311 241657 246946
D52331 D42331 D5B331 D4B331 Stainless Steel Stainless Steel PTFE D05331 241657 246946
D52336 D42336 D5B336 D4B336 Stainless Steel Stainless Steel Santoprene D05336 241657 246946
D52911 D42911 D5B911 D4B911 Polypropylene PTFE PTFE D05911 241657 246946
D52955 D42955 D5B955 D4B955 Polypropylene TPE TPE D05955 241657 246946
D52966 D42966 D5B966 D4B966 Polypropylene Santoprene Santoprene D05966 241657 246946
D52977 D42977 D5B977 D4B977 Polypropylene Buna Buna D05977 241657 246946
D52988 D42988 D5B988 D4B988 Polypropylene Fluoroelastomer Fluoroelastomer D05988 241657 246946
D52D05 D42D05 D5BD05 D4BD05 Duckbill TPE D05D05 241657 246946
D52D06 D42D06 D5BD06 D4BD06 Duckbill Santoprene D05D06 241657 246946
D52D07 D42D07 D5BD07 D4BD07 Duckbill Buna D05D07 241657 246946
PVDF D55A11 D45A11 D5EA11 D4EA11 PVDF PTFE PTFE D05A11 241657 246946
D55A88 D45A88 D5EA88 D4EA88 PVDF Fluoroelastomer Fluoroelastomer D05A88 241657 246946
*Required Cycleflo or external valve control
** Air control includes air regulator and filter with gauge

12
process equipment catalog
 Husky 515 Plastic Pumps

Technical Specifications

Husky 515 Plastic Pumps Acetal Polypropylene PVDF

Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa)
Maximum free flow delivery* 15 gpm (57 lpm) 15 gpm (57 lpm) 15 gpm (57 lpm)
Maximum pump speed 400 cpm 400 cpm 400 cpm
Displacement per cycle** 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter)
Maximum suction lift 15 ft (4.5 m) dry 15 ft (4.5 m) dry 15 ft (4.5 m) dry
Maximum size pumpable solids 0.09 in (2.5 mm) 0.09 in (2.5 mm) 0.09 in (2.5 mm)
Maximum operating temperature*** 180°F (82°C) 150°F (66°C) 150°F (66°C)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C) 180°F (82.2°C)
Buna-N 180°F (82.2°C) 180°F (82.2°C) 180°F (82.2°C)
TPE 150°F (65.5°C) 150°F (65.5°C) 150°F (65.5°C)
Fluoroelastomer 250°F (121.1°C) 250°F (121.1°C) 250°F (121.1°C)
Typical sound level at 70 psi 74 dBa 74 dBa 74 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min)
Air pressure operating range 30 to 100 psi 30 to 100 psi 30 to 100 psi
(2.1 to 7 bar, 0.21 to 0.7 MPa) (2.1 to 7 bar, 0.21 to 0.7 MPa) (2.1 to 7 bar, 0.21 to 0.7 MPa)
Air inlet size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f)
Air exhaust port size 3/8 npt(f) 3/8 npt(f) 3/8 npt(f)
Fluid inlet & outlet size**** 1/2 npt(f) or bspt(f) 1/2 npt(f) or bspt(f) 1/2 npt(f) or bspt(f)
Weight 7.8 lb (3.5 kg) 6.5 lb (2.9 kg) 8.5 lb (3.9 kg)
Wetted parts Groundable Acetal, PTFE, SST Polypropylene, PTFE, SST PVDF, PTFE
(in addition to ball, seat and diaphragm materials–
which may vary by pump)
Instruction manual 308981 308981 308981
*Flow rates are with muffler and do not vary based on diaphragm material. **Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
***Actual pump performance may be affected by prolonged usage at temperature. **** Hybrid thread allows for either 1/4 npt or 1/4 bspt fitting

Performance Charts
Husky 515 Performance
100 30
(7, 0.7) (0.84)

80 A A 24
FluID outlet PreSSure psi (bar, MPa)

(5.5, 0.55) (0.67)

aIr conSumPtIon scfm (m3/min)

60 18
(4.1, 0.41) B (0.50)
B

40 12
(2.8, 0.28) C (0.37)
C
20 6
(1.4, 0.14) (0.17)
D
D
0
gpm 0 4 8 12 16
(lpm) (15.2) (30) (45.42) (60.56)
FluiD FlOW
(Pump tested in water with inlet submerged

aIr PreSSure legenD

A = at 100 psi (7 bar, 0.7 MPa) Air Consumption
B = at 70 psi (4.8 bar, 0.48 MPa) Fluid Flow
C = at 40 psi (2.8 bar, 0.28 MPa)
D = at 20 psi (1.4 bar, 0.14 MPa)

13
process equipment catalog
 Husky 515 Plastic Pumps

Dimensions

1/2 npt(f) or bspt(f)

Fluid Outlet
1/4 npt(f) 4.7 in 5.01 in
Air Inlet (119 mm) (127 mm) 3/4 npt(f)
Outlet

10.63 in
(270 mm)

9.94 in
7.75 in (252.5 mm)
(196.9 mm)

8.56 in
(217.4 mm)

3/4 npt(f)
Inlet
6.12 in
(155.4 mm)
1/2 npt(f) or bspt(f) Fluid Inlet 3/4 npt(f) or bspt(f) Fluid Inlet

Typical System Drawings

Husky 515 Wall-Mount with Drum Feed Husky 515 Drum-Mount with Siphon Feed

14
process equipment catalog
 Husky 716 Metal Pumps
Air-Operated Double Diaphragm

Ordering Information

D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

5 = 3/4” (19.05 mm) Standard: polypropylene center section 3 = Aluminum (npt) 2 = Acetal 1 = PTFE 1 = PTFE
4 = 3/4” (19.05 mm) Remote: polypropylene center section 4 = Stainless Steel (npt) 3 = Stainless Steel 3 = Stainless Steel 5 = TPE
9 = Polypropylene 5 = TPE 6 = Santoprene
C = Aluminum (bsp) A = PVDF 6 = Santoprene 7 = Buna N
D = Stainless Steel (bsp) D = Duckbill 7 = Buna N 8 = Fluoroelastomer
8 = Fluoroelastomer

Popular Models

Part Number Part Number

(NPT Ported) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control**
Aluminum D53211 D43211 D5C211 D4C211 Acetal PTFE PTFE D05211 241657 246946
D53255 D43255 D5C255 D4C255 Acetal TPE TPE D05255 241657 246946
D53277 D43277 D5C277 D4C277 Acetal Buna Buna D05277 241657 246946
D53288 D43288 D5C288 D4C288 Acetal Fluoroelastomer Fluoroelastomer D05288 241657 246946
D53311 D43311 D5C311 D4C311 Stainless Steel PTFE PTFE D05311 241657 246946
D53331 D43331 D5C331 D4C331 Stainless Steel Stainless Steel PTFE D05331 241657 246946
D53355 D43355 D5C355 D4C355 Stainless Steel TPE TPE D05355 241657 246946
D53366 D43366 D5C366 D4C366 Stainless Steel Santoprene Santoprene D05366 241657 246946
D53377 D43377 D5C377 D4C377 Stainless Steel Buna Buna D05377 241657 246946
D53388 D43388 D5C388 D4C388 Stainless Steel Fluoroelastomer Fluoroelastomer D05388 241657 246946
D53911 D43911 D5C911 D4C911 Polypropylene PTFE PTFE D05911 241657 246946
D53955 D43955 D5C955 D4C955 Polypropylene TPE TPE D05955 241657 246946
D53966 D43966 D5C966 D4C966 Polypropylene Santoprene Santoprene D05966 241657 246946
D53977 D43977 D5C977 D4C977 Polypropylene Buna Buna D05977 241657 246946
D53D05 D43D05 D5CD05 D4CD05 Duckbill TPE D05D05 241657 246946
D53D06 D43D06 D5CD06 D4CD06 Duckbill Santoprene D05D06 241657 246946
D53D07 D43D07 D5CD07 D4CD07 Duckbill Buna D05D07 241657 246946
Stainless Steel D54211 D44211 D5D211 D4D211 Acetal PTFE PTFE D05211 241657 246946
D54311 D44311 D5D311 D4D311 Stainless Steel PTFE PTFE D05311 241657 246946
D54331 D44331 D5D331 D4D331 Stainless Steel Stainless Steel PTFE D05331 241657 246946
D54335 D44335 D5D335 D4D335 Stainless Steel Stainless Steel TPE D05335 241657 246946
D54336 D44336 D5D336 D4D336 Stainless Steel Stainless Steel Santoprene D05336 241657 246946
D54355 D44355 D5D355 D4D355 Stainless Steel TPE TPE D05355 241657 246946
D54366 D44366 D5D366 D4D366 Stainless Steel Santoprene Santoprene D05366 241657 246946
D54377 D44377 D5D377 D4D377 Stainless Steel Buna Buna D05377 241657 246946
D54388 D44388 D5D388 D4D388 Stainless Steel Fluoroelastomer Fluoroelastomer D05388 241657 246946
D54911 D44911 D5D911 D4D911 Polypropylene PTFE PTFE D05911 241657 246946
D54966 D44966 D5D966 D4D966 Polypropylene Santoprene Santoprene D05966 241657 246946
* Requires CycleFlo or external valve control
** Air control includes air regulator and filter with gauge

15
process equipment catalog
 Husky 716 Metal Pumps

Technical Specifications

Husky 716 Metal Pumps Aluminum Stainless Steel

Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa)
Maximum free flow delivery* 16 gpm (61 lpm) 16 gpm (61 lpm)
Maximum pump speed 400 cpm 400 cpm
Displacement per cycle** 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter)
Maximum suction lift 15 ft (4.5 m) dry 15 ft (4.5 m) dry
Maximum size pumpable solids 0.09 in (2.5 mm) 0.09 in (2.5 mm)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C)
Buna-N 180°F (82.2°C) 180°F (82.2°C)
TPE 150°F (65.5°C) 150°F (65.5°C)
Fluoroelastomer 250°F (121.1°C) 250°F (121.1°C)
Typical sound level at 70 psi air 74 dBa 74 dBa
(4.9 bar, 0.49 MPa) air @ 200 cpm
Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min)
Air pressure operating range 30 to 100 psi 30 to 100 psi
(2.1 to 7 bar, 0.21 to 0.7 MPa) (2.1 to 7 bar, 0.21 to 0.7 MPa)
Air inlet size 1/4 npt(f) 1/4 npt(f)
Air exhaust port size 3/8 npt(f) 3/8 npt(f)
Fluid inlet & outlet size 3/4 npt(f) or bspt(f) 3/4 npt(f) or bspt(f)
Weight 8.5 lb (3.9 kg) 18 lb (8.2 kg)
Wetted parts (in addition to ball, seat and Aluminum, Stainless Steel, PTFE, Acetal, Polypropylene, Stainless Steel,
diaphragm materials–which may vary by pump) Buna-N, Santroprene, Zinc-Plated Steel Polyester, Santoprene, Fluoroelastomer,
Nickel-Plated Brass, Epoxy-Coated Steel
Instruction manual 308981 308981
*Flow rates are with muffler and do not vary based on diaphragm material
**Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
***Actual pump performance may be affected by prolonged usage at temperature

Performance Charts

Husky 716 Performance

100 30
(7, 0.7) (0.84)

80 A A 24
FluID outlet PreSSure psi (bar, MPa)

(5.5, 0.55) (0.67)

aIr conSumPtIon scfm (m3/min)

60 18
(4.1, 0.41) B (0.50)
B

40 12
(2.8, 0.28) C (0.37)
C
20 6
(1.4, 0.14) (0.17)
D
D
0
gpm 0 4 8 12 16
(lpm) (15.2) (30) (45.42) (60.56)
FluiD FlOW
(Pump tested in water with inlet submerged

aIr PreSSure legenD

A = at 100 psi (7 bar, 0.7 MPa) Air Consumption
B = at 70 psi (4.8 bar, 0.48 MPa) Fluid Flow
C = at 40 psi (2.8 bar, 0.28 MPa)
D = at 20 psi (1.4 bar, 0.14 MPa)

16
process equipment catalog
 Husky 716 Metal Pumps

Dimensions

3/4 npt(f) or bspt(f) Fluid Outlet 2.76 in

4.25 in 3/4 npt(f) (62.5 mm)
(108 mm) 4.44 in Outlet
(112.8 mm)
1/4 npt(f) 3/4 npt(f)
Air Inlet or bsp(f)
Fluid Outlets

10.43 in
(264.9 mm)

9.18 in
(233.2 mm)

7.37 in 7.8 in
(187.2 mm) (198.1 mm)

3/4 npt(f)
6.62 in
or bsp(f)
(168.1 mm) 4.29 in (109 mm) Fluid Inlets
3/4 npt(f) or bspt(f) Fluid Inlets 3/4 npt(f)
Inlet 6.04 in (153.4 mm)

Typical System Drawings

Husky 716 Wall-Mount with Drum Feed Husky 716 Drum-Mount with Siphon Feed

17
process equipment catalog
 Husky 1050 Plastic Pumps
Air-Operated Double Diaphragm

Husky 1050 Selector Tool

To order a Husky 1050, use the online selector tool at
www.graco.com/process or contact your distributor.

PART NO. CONFIGURATION NO. SERIAL NO.

DATE CODE SERIES MAX WPR PSI-bar MADE IN

Pump ID

NOTE: Options for seats, check balls, diaphragms, and seals

vary for the 1050A, 1050C, 1050F, 1050H, 1050P, and 1050S
pump models.
Example of Product Selector Tool on www.graco.com/process.

Pump Configurations

Pump Center Section and

(1 inch ports, 50 gpm) Air Valve Material Air Valve/Monitoring Fluid Covers and Manifolds
1050C ★ Conductive C01A Standard C1 Conductive polypropylene, center flange
Conductive Polypropylene C2 Conductive polypropylene, end flange
C01B Pulse Count ✖
Polypropylene
C01C DataTrak ✖
1050P C01D Remote P1 Polypropylene, center flange
Polypropylene Polypropylene P01A Standard P2 Polypropylene, end flange
P01B Pulse Count ✖
1050F F1 PVDF, center flange
P01C DataTrak ✖
PVDF
P01D Remote F2 PVDF, end flange
★, ‡, or ✖: See ATEX Certifications below.

Check Valve Seats Check Valve Balls Diaphragm Manifold O-Rings

AC Acetal AC Acetal BN Buna-N — None
FK FKM Fluoroelastomer BN Buna-N CO Polychloroprene Overmolded PT PTFE
PP Polypropylene FK FKM Fluoroelastomer FK FKM Fluoroelastomer
PV PVDF PT PTFE PO PTFE/EPDM Overmolded
SP Santoprene® SP Santoprene PT PTFE/EPDM Two-Piece
SS 316 Stainless Steel SS 316 Stainless Steel SP Santoprene
BN Buna-N TP TPE TP TPE
AL Aluminum GE Geolast GE Geolast
GE Geolast CR Polychloroprene
TP TPE CW Polychloroprene w/SST Core

ATEX Certifications EEx ia IIA T3

★ A ll 1050C (Conductive Polypropylene) ✖ DataTrak and Pulse Nemko
pumps are certified: II 2 G c IIC T4 Count are certified: II 2 G 06ATEX1124

18
process equipment catalog
 Husky 1050 Plastic Pumps

Popular Models
Part Number
Standard Materials for Materials for Air Valve Diaphragm
Material Air Valve Seats Balls Materials for Diaphragms Replacement Kit Seat Kit Ball Kit Kit Flange
Polypropylene 649001 Polypropylene Santoprene Santoprene 24B773 24B635 24B646 24B628 Center
649006 Polypropylene PTFE PTFE/EPDM 2 Piece 24B773 24B635 24B645 24B627 Center
649034 Polypropylene PTFE PTFE/EPDM 2 Piece 24B773 24B635 24B645 24B627 End
Conductive End
649218 Acetal PTFE PTFE/EPDM 2 Piece 24B775 24B630 24B645 24B627
Polypropylene
649211 316 SST PTFE PTFE/EPDM 2 Piece 24B775 24B637 24B645 24B627 End
PVDF 649392 316 SST PTFE PTFE/EPDM 2 Piece 24B773 24B637 24B645 24B627 End
649398 PVDF PTFE PTFE/EPDM 2 Piece 24B773 24C721 24B645 24B627 End

Technical Specifications

Husky 1050 Plastic Pumps Conductive Polypropylene Polypropylene PVDF

Maximum fluid working pressure 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa)
Maximum free flow delivery 50 gpm (189 lpm) 50 gpm (189 lpm) 50 gpm (189 lpm)
Maximum pump speed 280 cpm 280 cpm 280 cpm
Displacement per cycle 0.17 gal (0.64 liters) 0.17 gal (0.64 liters) 0.17 gal (0.64 liters)
Maximum suction lift 16 ft (4.9 m) dry, 29 ft (8.8 m) wet 16 ft (4.9 m) dry, 29 ft (8.8 m) wet 16 ft (4.9 m) dry, 29 ft (8.8 m) wet
Maximum size pumpable solids 1/8 in (3.2 mm) 1/8 in (3.2 mm) 1/8 in (3.2 mm)
Sound Power*
at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm 78 dBa 78 dBa 78 dBa
at 100 psi (7.0 bar, 0.7 MPa) and full flow 90 dBa 90 dBa 90 dBa
Sound Pressure**
at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm 84 dBa 84 dBa 84 dBa
at 100 psi (7.0 bar, 0.7 MPa) and full flow 96 dBa 96 dBa 96 dBa
Maximum air consumption 67 scfm 67 scfm 67 scfm
Air consumption at 70 psi (4.8 bar, 0.48 MPa), 25 scfm 25 scfm 25 scfm
20 gpm (76 lpm)
Air pressure operating range 20-125 psi (1.4-8.6 bar, 20-125 psi (1.4-8.6 bar, 20-125 psi (1.4-8.6 bar,
0.14-0.86 MPa) 0.14-0.86 MPa) 0.14-0.86 MPa)
Air inlet size 1/2 npt(f) 1/2 npt(f) 1/2 npt(f)
Fluid inlet size 1 in raised face ANSI/DIN flange 1 in raised face ANSI/DIN flange 1 in raised face ANSI/DIN flange
Fluid outlet size 1 in raised face ANSI/DIN flange 1 in raised face ANSI/DIN flange 1 in raised face ANSI/DIN flange
Weight 18 lb (8.2 kg) 18 lb (8.2 kg) 26 lb (11.8 kg)
Wetted parts polypropylene and material(s) polypropylene and material(s) PVDF and material(s) chosen for
chosen for seat, ball, and chosen for seat, ball, and seat, ball, and diaphragm options
diaphragm options diaphragm options
Non-wetted Parts
Center polypropylene polypropylene polypropylene
Bolts stainless steel stainless steel stainless steel
Instruction manual 312877 312877 312877
Repair/parts manual 313435 313435 313435
* Sound power measured per ISO-9614-2.
** Sound pressure was tested 3.28 ft (1 m) from equipment.

19
process equipment catalog
 Husky 1050 Plastic Pumps
Polypropylene (1050P) and Conductive Polypropylene (1050C)
Performance Charts Dimensions
Husky 1050 Performance Center Flange: 16.0 in. (406 mm)
1 in. ANSI/DIN End Flange: 15.2 in. (386 mm)
120 60
flange
(8.3, 0.83) (1.68)
A A 8.0 in.
100 3/4 npt(f) B 50 (203 mm)
air exhaust port
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (1.4)

B

aIr conSumPtIon scfm (m3/min)

80 40
(5.5, 0.55) (1.12)
C
60 C 30
(4.1, 0.41) (0.84)
1/2 npt(f)
40 20 air inlet
13.2 in. D
(2.8, 0.28) D (0.56)
(335 mm) 17.8 in.
20 15.7 in. 10 (452 mm) 12.0 in.
(1.4, 0.14) (399 mm) (0.28) (305 mm)
Polypropylene (1050P) and Conductive Polyprop
0
gpm 0 5 10 15 20 25 30 35 40 45
(lpm) (19) (38) (57) (76) (95) (114) (133) (152) (152)
2.5 in.
FluiD FlOW gpm (lpm)
(63.5inlet
(Pump tested in water with mm) submerged)
Center F
1 in. ANSI/DIN End Flan
aIr PreSSure legenD flange
1 in. ANSI/DIN flange
A = at 125 psi (8.3 bar, 0.83 MPa) Air Consumption
8.0 in.
3/4 npt(f) (203 mm)
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow air exhaust port
C = at 70 psi (4.8 bar, 0.48 MPa)
D = at 40 psi (2.8 bar, 0.28 MPa)

Mounting Pattern
10.3" 13.2 in.
(335 mm) 17.8 in.
15.7 in. (452 mm) 12.0 in.
5.6 in. (305 mm)
(399 mm)
(142 mm)
5.0" 9.6 in.
(244 mm)
5.0 in.
(127 mm)
3.9 in. 2.5 in.
(99 mm) (63.5 mm)

10.3 in. 1 in. ANSI/DIN flange

Typical System Drawings (262 mm)

Husky 1050 Floor-Mount

5.6 in.
(142 mm)
9.6 in.
(244 mm)

3.9 in.
(99 mm)

10.3 in
(262 mm

20
process equipment catalog
 Husky 1050 Metal Pumps
Air-Operated Double Diaphragm

Husky 1050 Selector Tool

To order a Husky 1050, use the online selector tool at
www.graco.com/process or contact your distributor.

PART NO. CONFIGURATION NO. SERIAL NO.

DATE CODE SERIES MAX WPR PSI-bar MADE IN

Pump ID

NOTE: Options for seats, check balls, diaphragms, and seals

vary for the 1050A, 1050C, 1050F, 1050H, 1050P, and 1050S
pump models. Example of Product Selector Tool on www.graco.com/process.

Pump Configurations
Pump Center Section and
(1 inch ports, 50 gpm) Air Valve Material Air Valve/Monitoring Fluid Covers and Manifolds
1050A ★ Aluminum A01 Standard A1 Aluminum, standard ports, inch
Aluminum A01B Pulse Count ✖ A2 Aluminum, standard ports, metric
A01C DataTrak ✖ S1 Stainless steel, standard ports, inch
1050S ‡ A01D Remote S2 Stainless steel, standard ports, metric
Stainless Steel Conductive C01A Standard H1 Hastelloy, standard ports, inch
Polypropylene H2 Hastelloy, standard ports, metric
1050H Polypropylene P01A Standard
Hastelloy P01B Pulse Count ✖
P01C DataTrak ✖
P01D Remote
★, ‡, or ✖: See ATEX Certifications below.

Check Valve Seats Check Valve Balls Diaphragm Manifold O-Rings

AC Acetal AC Acetal BN Buna-N — None
AL Aluminum BN Buna-N CO Polychloroprene Overmolded PT PTFE
BN Buna-N CR Polychloroprene Standard FK FKM Fluoroelastomer
FK FKM Fluoroelastomer CW Polychloroprene Weighted GE Geolast
GE Geolast® FK FKM Fluoroelastomer PO PTFE/EPDM Overmolded
PP Polypropylene GE Geolast PT PTFE/EPDM Two-Piece
SP Santoprene® PT PTFE SP Santoprene
SS 316 Stainless Steel SP Santoprene TP TPE
TP TPE SS 316 Stainless Steel
TP TPE

ATEX Certifications
★ A ll 1050A (Aluminum) pumps are certified: ‡ 1050S (Stainless Steel) pumps with aluminum or ✖ DataTrak and Pulse Count are certified:
conductive polypropylene centers are certified:
EEx ia IIA T3
Nemko
II 2 G c IIC T4 II 2 G c IIC T4 II 2 G 06ATEX1124

21
process equipment catalog
 Husky 1050 Metal Pumps

Popular Models
Part Number Air Valve
Standard Remote Materials for Materials for Materials for Replacement Diaphragm
Material Air Valve Air Valve Seats Balls Diaphragms Kit Seat Kit Ball Kit Kit
Thermoplastic Thermoplastic
Aluminum 647666 647502 Polyester Acetal Polyester 24B766 24B634 24B639 24B624
Elastomer Elastomer
Thermoplastic Thermoplastic
647016 Polyester Acetal Polyester 24B766 24B634 24B639 24B624
(UL Certified) Elastomer Elastomer
PTFE/EPDM
647075 647561 Acetal PTFE 24B766 24B630 24B645 24B627
2 Piece
647040 647526 Geolast Geolast Geolast 24B766 24B633 24B641 24B623
647035 647521 Santoprene Santoprene Santoprene 24B766 24B636 24B646 24B628
PTFE/EPDM
647028 647514 316 SST PTFE 24B766 24B637 24B645 24B627
2 Piece
PTFE/EPDM
647004 647490 Polypropylene PTFE 24B766 24B635 24B645 24B627
2 Piece
PTFE/EPDM
647018 647504 316 SST 316 SST 24B766 24B637 24B647 24B627
2 Piece
PTFE/EPDM
Stainless Steel 651009 651125 316 SST PTFE 24B766 24B637 24B645 24B627
2 Piece
PTFE/EPDM
Hastelloy 651440 FKM PTFE 24B773 24B638 24B645 24B627
2 Piece

Typical System Drawings

Husky 1050 Bung-Mount Husky 1050 Floor-Mount

FIG. 3. Typical bung-mount installation (aluminum, 1050A, pump shown)

22
process equipment catalog
 Husky 1050 Metal Pumps

Technical Specifications

Husky 1050 Metal Pumps Aluminum Stainless Steel Hastelloy

Maximum fluid working pressure 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa)
Maximum free flow delivery 50 gpm (189 lpm) 50 gpm (189 lpm) 50 gpm (189 lpm)
Maximum pump speed 280 cpm 280 cpm 280 cpm
Displacement per cycle 0.17 gal (0.64 liters) 0.17 gal (0.64 liters) 0.17 gal (0.64 liters)
Maximum suction lift 16 ft (4.9 m) dry, 16 ft (4.9 m) dry, 16 ft (4.9 m) dry,
29 ft (8.8 m) wet 29 ft (8.8 m) wet 29 ft (8.8 m) wet
Maximum size pumpable solids 1/8 in (3.2 mm) 1/8 in (3.2 mm) 1/8 in (3.2 mm)
Sound Power*
at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm 78 dBa 78 dBa 78 dBa
at 100 psi (7.0 bar, 0.7 MPa) and full flow 90 dBa 90 dBa 90 dBa
Sound Pressure**
at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm 84 dBa 84 dBa 84 dBa
at 100 psi (7.0 bar, 0.7 MPa) and full flow 96 dBa 96 dBa 96 dBa
Maximum air consumption 67 scfm 67 scfm 67 scfm

Air consumption at 70 psi (4.8 bar, 25 scfm 25 scfm 25 scfm

0.48 MPa),20 gpm (76 lpm)
Air pressure operating range 20-125 psi (1.4-8.6 bar, 20-125 psi (1.4-8.6 bar, 20-125 psi (1.4-8.6 bar,
0.14-0.86 MPa) 0.14-0.86 MPa) 0.14-0.86 MPa)
Air inlet size 1/2 npt(f) 1/2 npt(f) 1/2 npt(f)
Fluid inlet size 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt
Fluid outlet size 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt
Weight 23 lb (10.5 kg) with conductive 41 lb (18.6 kg)
polypropylene center 36.3 lb (16.5 kg)
with polypropylene center 37.3 lb (16.9 kg)
with aluminum center 41.4 lb (18.8 kg)
Wetted parts aluminum and material(s) stainless steel and material(s) chosen for seat, hastelloy, stainless steel and
chosen for seat, ball, and ball, and diaphragm options material(s) chosen for seat, ball, and
diaphragm options diaphragm options
Non-wetted Parts
Center aluminum polypropylene aluminum polypropylene
Bolts coated carbon steel stainless steel Husky
stainless steel1050 Performance
stainless steel
120 60
Instruction manual 312877 312877 312877 (1.68)
(8.3, 0.83)
Repair/parts manual 313435 313435 A 313435
A
100 B 50
* Sound power measured per ISO-9614-2. ** Sound pressure was tested 3.28 ft (1 m) from equipment.
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (1.4)

B
Performance Charts
aIr conSumPtIon scfm (m3/min)

80 40
(5.5, 0.55) (1.12)
C
Husky 1050 Performance
60 60 C 30
120
(4.1, 0.41)
(1.68) (0.84)
(8.3, 0.83)
A A
100 B 50 40 D 20
(2.8,
(1.4)0.28) D (0.56)
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7)
B
aIr conSumPtIon scfm (m3/min)

80 40 20 10
(5.5, 0.55) (1.4, 0.14)
(1.12) (0.28)
C
60 C 30 0
(4.1, 0.41) (0.84)
gpm 0 5 10 15 20 25 30 35 40 45
(lpm) (19) (38) (57) (76) (95) (114) (133) (152) (152)
40 D 20
D (0.56) FluiD FlOW gpm (lpm)
(2.8, 0.28)
(Pump tested in water with inlet submerged)
20 10
(1.4, 0.14) (0.28) aIr PreSSure legenD
A = at 125 psi (8.3 bar, 0.83 MPa) Air Consumption
0
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow
gpm 0 5 10 15 20 25 30 35 40 45
(lpm) (19) (38) (57) (76) (95) (114) (133) (152) (152) C = at 70 psi (4.8 bar, 0.48 MPa)
FluiD FlOW gpm (lpm) D = at 40 psi (2.8 bar, 0.28 MPa)
(Pump tested in water with inlet submerged)

23
aIr PreSSure legenD process equipment catalog
A = at 125 psi (8.3 bar, 0.83 MPa) Air Consumption
 Husky 1050 Metal Pumps
Aluminum (1050A)
Dimensions

Aluminum 1 in. npt(f) or 1 in. bspt 14.7 in.

(373 mm)
fluid outlet ports (4)
7.3 in.
(185 mm)
3/4 npt(f) air exhaust port

1/2 npt(f)
14.4 in. 12.7 in. air inlet
(366 mm) (323 mm)

15.9 in.
(404 mm) 10.9 in.
(277 mm)

1.8 in.
(46 mm)

1 in. npt(f) or 1 in. bspt fluid inlet ports (4)

Mounting Pattern
5.5"

6.1 in. (155 mm)

5.0" 10.0 in.

(254 mm) 5.0 in.
(127 mm)

Stainless Steel (1050S)

3.9 in. (99 mm)

5.5 in.
(140 mm)
Stainless Steel
1 in. npt(f) or 1 in. bspt fluid outlet ports (4) 13.9 in.
(353 mm)
3/4 npt(f) air exhaust port

1/2 npt(f)
air inlet
11.8 in.
(300 mm) 13.7 in.
(348 mm) 9.5 in.
12.9 in. (241 mm)
(328 mm)

1.1 in. (28 mm)

1 in. npt(f) or 1 in. bspt fluid inlet ports (4)

Mounting Pattern
5.5"

5.0"
5.7 in.
(145 mm)

9.6 in.
(245 mm) 5.0 in.
(127 mm)

24 4.0 in.
process equipment catalog (102 mm)
 Husky 1590 Plastic Pumps
Air-Operated Double Diaphragm

Ordering Information

D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

B = 1-1/2” (38.1 mm) Standard: aluminum center section 2 = Poly (flange) 3 = Stainless Steel 1 = PTFE 1 = PTFE
C = 1-1/2” (38.1 mm) Remote: aluminum center section 5 = PVDF (flange) 4 = Hardened SST 2 = Acetal 5 = TPE
T = 1-1/2” (38.1 mm) Standard: stainless steel center section 5 = TPE 4 = Hardened SST 6 = Santoprene
U = 1-1/2” (38.1 mm) Remote: stainless steel center section 6 = Santoprene 5 = TPE 7 = Buna N
7 = Buna N 6 = Santoprene 8 = Fluoroelastomer
8 = Fluoroelastomer 7 = Buna N G = Geolast
9 = Polypropylene 8 = Fluoroelastomer
A = PVDF G = Geolast
G = Geolast

Popular Models
Part Number Part Number
(ANSI-Flange) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control**
Standard Pumps with Aluminum Center Section
Polypropylene DB2311 Stainless Steel PTFE PTFE D0C311 236273 246947
DB2377 DC2377 Stainless Steel Buna Buna D0C377 236273 246947
DB2777 DC2777 Buna Buna Buna D0C777 236273 246947
DB2888 DC2888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0C888 236273 246947
DB2911 DC2911 Polypropylene PTFE PTFE D0C911 236273 246947
DB2955 Polypropylene TPE TPE D0C955 236273 246947
DB2966 Polypropylene Santoprene Santoprene D0C966 236273 246947
DB2977 Polypropylene Buna Buna D0C977 236273 246947
DB2988 Polypropylene Fluoroelastomer Fluoroelastomer D0C988 236273 246947
DB29GG DC29GG Polypropylene Geolast Geolast D0C9GG 236273 246947
PVDF DB5311 Stainless Steel PTFE PTFE D0C311 236273 246947
DB5666 Santoprene Santoprene Santoprene D0C666 236273 246947
DB5811 DC5811 Fluoroelastomer PTFE PTFE D0C811 236273 246947
DB5888 DC5888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0C888 236273 246947
DB5A11 DC5A11 PVDF PTFE PTFE D0CA11 236273 246947
DB5A88 PVDF Fluoroelastomer Fluoroelastomer D0CA88 236273 246947
Corrosion Resistant Pumps with Stainless Steel Center Section
Polypropylene DT2311 DU2311 Stainless Steel PTFE PTFE D0C311 236273 246947
DT2341 DU2331 Hardened SST Stainless Steel PTFE D0C331 236273 246947
DT2377 DU2377 Stainless Steel Buna Buna D0C377 236273 246947
DT2888 DU2888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0C888 236273 246947
DT2911 DU2911 Polypropylene PTFE PTFE D0C911 236273 246947
DT2977 DU2977 Polypropylene Buna Buna D0C977 236273 246947
DT2988 DU2988 Polypropylene Fluoroelastomer Fluoroelastomer D0C988 236273 246947
PVDF DT5311 DU5311 Stainless Steel PTFE PTFE D0C311 236273 246947
DT5811 DU5811 Fluoroelastomer PTFE PTFE D0C811 236273 246947
DT5888 DU5888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0C888 236273 246947
DT5A11 DU5A11 PVDF PTFE PTFE D0CA11 236273 246947
DT5A88 DU5A88 PVDF Fluoroelastomer Fluoroelastomer D0CA88 236273 246947
*Requires CycleFlo or external valve control
** Air control includes air regulator and filter with gauge

25
process equipment catalog
 Husky 1590 Plastic Pumps

Technical Specifications

Husky 1590 Plastic Pumps Polypropylene PVDF

Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa)
Maximum free flow delivery* 100 gpm (378.5 lpm) 100 gpm (378.5 lpm)
Maximum pump speed 200 cpm 200 cpm
Displacement per cycle** 0.5 gallon (1.96 liter) 0.5 gallon (1.96 liter)
Maximum suction lift (DB2366) 20 ft (6.1 m) dry 20 ft (6.1 m) dry
Maximum size pumpable solids 0.19 in (4.8 mm) 0.19 in (4.8 mm)
Maximum operating temperature*** 150°F (65.5°C) 150°F (65.5°C)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C)
Buna-N 180°F (82.2°C) 180°F (82.2°C)
TPE 150°F (65.5°C) 150°F (65.5°C)
Fluoroelastomer 250°F (121.1°C) 250°F (121.1°C)
Geolast 150°F (65.5°C) 150°F (65.5°C)
Typical sound level at 70 psi 77 dBa 77 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 125 scfm (3.5 m3/min.) 125 scfm (3.5 m3/min.)
Air pressure operating range 20 to 120 psi 20 to 120 psi
(1.4 to 8.4 bar, 0.14 to 0.84 MPa) (1.4 to 8.4 bar, 0.14 to 0.84 MPa)
Air inlet size 1/2 npt(f) 1/2 npt(f)
Fluid inlet & outlet size**** 1-1/2 in (38.1 mm) ANSI-flange 1-1/2 in (38.1 mm) ANSI-flange
Weight 35 lb (16 kg) 49 lb (22 kg)
Weight with stainless steel center section 48.3 lb (21.9 kg) 62.3 lb (28.2 kg)
Instruction manual 308549 308549
* Flow rates are with muffler and do not vary based on diaphragm material
** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
*** Actual pump performance may be affected by prolonged usage at temperature

26
process equipment catalog
 Husky 1590 Plastic Pumps

Performance Charts Dimensions

7.55 in 10 in
Husky 1590 Performance (191.77 mm) (254 mm)
120 100
(8.4, 0.84) (2.80)
A 85
100 1/2 npt(f)
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (2.38) Air Inlet

B A

aIr conSumPtIon scfm (m3/min)

80 70 21.75 in
(552.5 mm)
(5.5, 0.55) (1.96) 16.25 in
B (412.5 mm)
60 55
(4.1, 0.41) C (1.54) 11.99 in
C (304.5 mm)
19.25 in
(489 mm)
40 40
(2.8, 0.28) D (1.12)
D
20 25 3.0 in
(76 mm)
(1.4, 0.14) (0.70)
3/4 npt(f) 6.0 in (152.5 mm)
Air Exhaust
0 (muffler included) 17.55 in (445.5 mm)
gpm 0 20 40 60 80 100 120
(lpm) (76) (152) (227) (303) (379) (454)
FluiD FlOW Outlet Port ID:
(Pump tested in water with inlet submerged 1.75 in (44.5 mm)
Flange Diameter:
5.5 in (140 mm)
aIr PreSSure legenD
A = at 120 psi (8.4 bar, 0.84 MPa) Air Consumption Eight Slots:
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow 0.73 in (18.5 mm)

C = at 70 psi (4.8 bar, 0.48 MPa)

D = at 40 psi (2.8 bar, 0.28 MPa)

Inlet Port ID:

1.75 in (44.5 mm)

0.5 in
6.0 in (152.5 mm)
(13 mm)
10.45 in (265.5 mm)

Typical System Drawings

Husky 1590 Above Ground Gravity Feed

27
process equipment catalog
 Husky 1590 Metal Pumps
Air-Operated Double Diaphragm

Ordering Information
D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

B = 1-1/2” (38.1 mm) Standard: aluminum center section 3 = Aluminum (npt) 3 = Stainless Steel 1 = PTFE 1 = PTFE
C = 1-1/2” (38.1 mm) Remote: aluminum center section 4 = Stainless Steel (npt) 4 = Hardened SST 2 = Acetal 5 = TPE
T = 1-1/2” (38.1 mm) Standard: stainless steel center section C = Aluminum (bsp) 5 = TPE 4 = Hardened SST 6 = Santoprene
U = 1-1/2” (38.1 mm) Remote: stainless steel center section D = Stainless Steel (bsp) 6 = Santoprene 5 = TPE 7 = Buna N
7 = Buna N 6 = Santoprene 8 = Fluoroelastomer
8 = Fluoroelastomer 7 = Buna N G = Geolast
9 = Polypropylene 8 = Fluoroelastomer
A = PVDF G = Geolast
G = Geolast

Popular Models
Part Number Part Number
(NPT Ported) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control**
Standard Pumps with Aluminum Center Section
Aluminum DB3311 DC3311 DBC311 DCC311 Stainless Steel PTFE PTFE D0B311 236273 246947
DB3341 DBC341 Hardened SST Stainless Steel PTFE D0B331 236273 246947
DB3366 DC3366 DBC366 DCC366 Stainless Steel Santoprene Santoprene D0B366 236273 246947
DB3377 DC3377 DBC377 DCC377 Stainless Steel Buna Buna D0B377 236273 246947
DB3525 DC3525 DBC525 DCC525 TPE Acetal TPE D0B525 236273 246947
DB3555 DBC555 TPE TPE TPE D0B555 236273 246947
DB3666 DC3666 DBC666 DCC666 Santoprene Santoprene Santoprene D0B666 236273 246947
DB3777 DC3777 DBC777 DCC777 Buna Buna Buna D0B777 236273 246947
DB3888 DC3888 DBC888 DCC888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0B888 236273 246947
DB3GGG DC3GGG DBCGGG DCCGGG Geolast Geolast Geolast D0BGGG 236273 246947
DB3911 DBC911 Polypropylene PTFE PTFE D0B911 236273 246947
DB3977 DBC977 Polypropylene Buna Buna D0B977 236273 246947
Stainless Steel DB4311 DC4311 DBD311 DCD311 Stainless Steel PTFE PTFE D0B311 236273 246947
DB4341 DBD341 Stainless Steel Hardened SST PTFE D0B341 236273 246947
DB4377 DC4377 DBD377 DCD377 Stainless Steel Buna Buna D0B377 236273 246947
DB4525 DBD525 TPE Acetal TPE D0B525 236273 246947
DB4666 DC4666 DBD666 DCD666 Santoprene Santoprene Santoprene D0B666 236273 246947
DB4777 DC4777 DBD777 DCD777 Buna Buna Buna D0B777 236273 246947
DB4888 DC4888 DBD888 DCD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0B888 236273 246947
DB4GGG DC4GGG DBDGGG DCDGGG Geolast Geolast Geolast D0BGGG 236273 246947
DB4911 DBD911 Polypropylene PTFE PTFE D0B911 236273 246947
Corrosion Resistant Pumps with Stainless Steel Center Section
Stainless Steel DT4311 DU4311 DTD311 DUD311 Stainless Steel PTFE PTFE D0B311 255061 246947
DT4377 DU4377 DTD377 DUD377 Stainless Steel Buna Buna D0B377 255061 246947
DT4388 DU4388 DTD388 DUD388 Stainless Steel Fluoroelastomer Fluoroelastomer D0B388 255061 246947
DT4666 DU4666 DTD666 DUD666 Santoprene Santoprene Santoprene D0B666 255061 246947
DT4888 DU4888 DTD888 DUD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0B888 255061 246947
DT4911 DU4911 DTD911 DUD911 Polypropylene PTFE PTFE D0B911 255061 246947
*Requires CycleFlo or external valve control
** Air control includes air regulator and filter with gauge

28
process equipment catalog
 Husky 1590 Metal Pumps

Technical Specifications

Husky 1590 Metal Pumps Aluminum Stainless Steel

Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa)
Maximum free flow delivery* 100 gpm (378.5 lpm) 100 gpm (378.5 lpm)
Maximum pump speed 200 cpm 200 cpm
Displacement per cycle** 0.5 gallon (1.96 liter) 0.5 gallon (1.96 liter)
Maximum suction lift (DB2366) 20 ft (6.1 m) dry 20 ft (6.1 m) dry
Maximum size pumpable solids 0.19 in (4.8 mm) 0.19 in (4.8 mm)
Maximum operating temperature*** 150°F (65.5°C) 150°F (65.5°C)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C)
Buna-N 180°F (82.2°C) 180°F (82.2°C)
TPE 150°F (65.5°C) 150°F (65.5°C)
Fluoroelastomer 250°F (121.1°C) 250°F (121.1°C)
Geolast 150°F (65.5°C) 150°F (65.5°C)
Typical sound level at 70 psi 77 dBa 77 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 125 scfm (3.5 m3/min.) 125 scfm (3.5 m3/min.)
Air pressure operating range 20 to 120 psi 20 to 120 psi
(1.4 to 8.4 bar, 0.14 to 0.84 MPa) (1.4 to 8.4 bar, 0.14 to 0.84 MPa)
Air inlet size 1/2 npt(f) 1/2 npt(f)
Fluid inlet & outlet size**** 1-1/2 npt(f) or bspt(f) 1-1/2 npt(f) or bspt(f)
Weight 33.5 lb (15.2 kg) 86 lb (40 kg)
Weight with stainless steel center section n/a 98.8 lb (44.8 kg)
Instruction manual 308441 308441
*Flow rates are with muffler and do not vary based on diaphragm material
**Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
*** Actual pump performance may be affected by prolonged usage at temperature

29
process equipment catalog
 Husky 1590 Metal Pumps

Performance Charts Dimensions

Husky 1590 Performance 7.19 in 7.75 in

120 100 (182.6 mm) (197 mm)
(8.4, 0.84) (2.80)
A 85
100
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (2.38) 1/2 npt(f)

B A
Air Inlet

aIr conSumPtIon scfm (m3/min)

80 70 19.0 in
(5.5, 0.55) (1.96) (482.5 mm)
B
60 55 16.25 in
(4.1, 0.41) C (1.54) (412.5 mm)
C
10.55 in
40 40 (268 mm)
(2.8, 0.28) (1.12) 17.75 in
D
(450 mm)
D
20 25
(1.4, 0.14) (0.70)

0
gpm 0 20 40 60 80 100 120 3/4 npt(f) 3.0 in
6.0 in (152.5 mm) (76 mm)
(lpm) (76) (152) (227) (303) (379) (454) Air Exhaust
FluiD FlOW (muffler included) 14.94 in (379.5 mm)
(Pump tested in water with inlet submerged

aIr PreSSure legenD Outlet Port ID:

1.5 npt(f)
A = at 120 psi (8.4 bar, 0.84 MPa) Air Consumption
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow
C = at 70 psi (4.8 bar, 0.48 MPa)
D = at 40 psi (2.8 bar, 0.28 MPa)

Inlet Port ID:

1.5 npt(f)

0.45 in
(11.5 mm) 6.0 in (152.5 mm)

10.46 in (265.5 mm)

Typical System Drawings

Husky 1590 Above Ground Gravity Feed

30
process equipment catalog
 Husky 2150 Plastic Pumps
Air-Operated Double Diaphragm

Ordering Information
D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

F = 2” (50.8 mm) Standard: aluminum center section 2 = Poly (npt) 3 = Stainless Steel 1 = PTFE 1 = PTFE
G = 2” (50.8 mm) Remote: aluminum center section 5 = PVDF (npt) 4 = Hardened SST 2 = Acetal 5 = TPE
V = 2” (50.8 mm) Standard: stainless steel center section 5 = TPE 4 = Hardened SST 6 = Santoprene
6 = Santoprene 5 = TPE 7 = Buna N
7 = Buna N 6 = Santoprene 8 = Fluoroelastomer
8 = Fluoroelastomer 7 = Buna N G = Geolast
9 = Polypropylene 8 = Fluoroelastomer
A = PVDF G = Geolast
G = Geolast

Popular Models

Part Number Part Number

(ANSI-Flange) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control**
Standard Pumps with Aluminum Center Section
Polypropylene DF2311 Stainless Steel PTFE PTFE D0G311 236273 246947
DF2377 DG2377 Stainless Steel Buna Buna D0G377 236273 246947
DF2777 DG2777 Buna Buna Buna D0G777 236273 246947
DF2888 DG2888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0G888 236273 246947
DF2911 DG2911 Polypropylene PTFE PTFE D0G911 236273 246947
DF2955 Polypropylene TPE TPE D0G955 236273 246947
DF2966 Polypropylene Santoprene Santoprene D0G966 236273 246947
DF2977 Polypropylene Buna Buna D0G977 236273 246947
DF2988 Polypropylene Fluoroelastomer Fluoroelastomer D0G988 236273 246947
DF29GG DG29GG Polypropylene Geolast Geolast D0G9GG 236273 246947
PVDF DF5311 Stainless Steel PTFE PTFE D0G311 236273 246947
DF5666 Santoprene Santoprene Santoprene D0G666 236273 246947
DF5811 DG5811 Fluoroelastomer PTFE PTFE D0G811 236273 246947
DF5888 DG5888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0G888 236273 246947
DF5A11 DG5A11 PVDF PTFE PTFE D0GA11 236273 246947
DF5A88 PVDF Fluoroelastomer Fluoroelastomer D0GA88 236273 246947
Corrosion Resistant Pumps with Stainless Steel Center Section
Polypropylene DV2311 Stainless Steel PTFE PTFE D0G311 236273 246947
DV2341 Stainless Steel Hardened SST PTFE D0G341 236273 246947
DV2377 Stainless Steel Buna Buna D0G377 236273 246947
DV2888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0G888 236273 246947
DV2911 Polypropylene PTFE PTFE D0G911 236273 246947
DV2977 Polypropylene Buna Buna D0G977 236273 246947
DV2988 Polypropylene Fluoroelastomer Fluoroelastomer D0G988 236273 246947
DV2A11 PVDF PTFE PTFE D0GA11 236273 246947
DV2A88 PVDF Fluoroelastomer Fluoroelastomer D0GA88 236273 246947
PVDF DV5311 Stainless Steel PTFE PTFE D0G311 236273 246947
DV5811 Fluoroelastomer PTFE PTFE D0G811 236273 246947
DV5888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0G888 236273 246947
DV5A11 PVDF PTFE PTFE D0GA11 236273 246947
DV5A88 PVDF Fluoroelastomer Fluoroelastomer D0GA88 236273 246947
*Requires CycleFlo or external valve control
** Air control includes air regulator and filter with gauge

31
process equipment catalog
 Husky 2150 Plastic Pumps

Technical Specifications

Husky 2150 Plastic Pumps Polypropylene PVDF

Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa)
Maximum free flow delivery* 150 gpm (568 lpm) 150 gpm (568 lpm)
Maximum pump speed 145 cpm 145 cpm
Displacement per cycle** 1.03 gallon (3.90 liter) 1.03 gallon (3.90 liter)
Maximum suction lift 18 ft (5.48 m) wet or dry 18 ft (5.48 m) wet or dry
Maximum size pumpable solids 0.25 in (6.3 mm) 0.25 in (6.3 mm)
Maximum operating temperature*** 150°F (65.5°C) 150°F (65.5°C)
Maximum diaphragm operating temperature***
PTFE 220°F (104.4°C) 220°F (104.4°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C)
Buna-N 180°F (82.2°C) 180°F (82.2°C)
TPE 150°F (65.5°C) 150°F (65.5°C)
Fluoroelastomer 250°F (121.1°C) 250°F (121.1°C)
Geolast 150°F (65.5°C) 150°F (65.5°C)
Typical sound level at 70 psi 78 dBa 78 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 175 scfm (4.9 m3/min) 175 scfm (4.9 m3/min)
Air consumption at 70 psi/60 gpm 60 scfm (1.7 m3/min) 60 scfm (1.7 m3/min)
Air pressure operating range 20 to 120 psi 20 to 120 psi
(1.4 to 8.4 bar, 0.14 to 0.84 MPa) (1.4 to 8.4 bar, 0.14 to 0.84 MPa)
Air inlet size 1/2 npt(f) 1/2 npt(f)
Fluid inlet & outlet size**** 2 in (51 mm) ANSI-flange 2 in (51 mm) ANSI-flange
Weight 49 lb (22 kg) 68 lb (30.8 kg)
Weight with stainless steel center section 68.5 lb (31 kg) 87.5 lb (39.6 kg)
Instruction manual 308550 308550
* Flow rates are with muffler and do not vary based on diaphragm material
** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
*** Actual pump performance may be affected by prolonged usage at temperature

32
process equipment catalog
 Husky 2150 Plastic Pumps

Performance Charts Dimensions

Husky 2150 Performance 8.69 in 11 in

150 (220.5 mm) (280.5 mm)
120
(8.4, 0.84) (4.2)
A
A
100 125
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (3.5)

B B

aIr conSumPtIon scfm (m3/min)

80 100 1/2 npt(f)
(5.5, 0.55) (2.8) Air Inlet
C C
25.75 in
60 75 (654 mm)
(4.1, 0.41) (2.1) 19.25 in
(489 mm)
40 50
(2.8, 0.28) D (1.4) 13.3 in
22.75 in
(350.5 mm)
(578 mm)
20 25
D
(1.4, 0.14) (0.7)

0 3.5 in
gpm 0 20 40 60 80 100 120 140 160 (89 mm)
(lpm) (76) (152) (227) (303) (379) (454) (531) (606)
FluiD FlOW 3/4 npt(f)
Air Exhaust 6.0 in (152.5 mm)
(Pump tested in water with inlet submerged
(muffler included)
19.74 in (501.5 mm)

aIr PreSSure legenD

A = at 120 psi (8.4 bar, 0.84 MPa) Air Consumption
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow Flange Diameter:
Port Diameter: 6 in (152.5 mm)
C = at 70 psi (4.8 bar, 0.48 MPa) 2.2 in (56 mm)
D = at 40 psi (2.8 bar, 0.28 MPa) Eight Slots:
0.75 in (19 mm)

0.5 in
(13 mm)

6.0 in (152.5 mm)

Typical System Drawings 12.5 in (317.5 mm)

Husky 2150 Above Ground Gravity Feed

33
process equipment catalog
 Husky 2150 Metal Pumps
Air-Operated Double Diaphragm

Ordering Information
D X X X X X
Diaphragm Wetted Seats Diaphragms
Pump Pump Parts Balls/
Size Checks

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

F = 2” (50.8 mm) Standard: aluminum center section 3 = Aluminum (npt) 3 = Stainless Steel 1 = PTFE 1 = PTFE
G = 2” (50.8 mm) Remote: aluminum center section 4 = Stainless Steel (npt) 4 = Hardened SST 2 = Acetal 5 = TPE
V = 2” (50.8 mm) Standard: stainless steel center section 6 = Ductile Iron (npt) 5 = TPE 4 = Hardened SST 6 = Santoprene
C = Aluminum (bsp) 6 = Santoprene 5 = TPE 7 = Buna N
D = Stainless Steel (bsp) 7 = Buna N 6 = Santoprene 8 = Fluoroelastomer
F = Ductile Iron (bsp) 8 = Fluoroelastomer 7 = Buna N G = Geolast
9 = Polypropylene 8 = Fluoroelastomer
H = 2 npt Alum Extended A = PVDF G = Geolast
G = 2 bsp Alum Extended G = Geolast
Popular Models
Part Number Part Number
(NPT Ported) (BSP Ported)
Standard Remote* Standard Remote* Materials for Materials for Materials for Fluid Air
Material Air Valve Air Valve Air Valve Air Valve Seats Balls Diaphragms Kit Air Kit Control**
Standard Pumps with Aluminum Center Section
Aluminum*** DF3311 DG3311 DFC311 DGC311 Stainless Steel PTFE PTFE D0F311 236273 246947
DF3341 DG3341 DFC341 DGC341 Stainless Steel Hardened SST PTFE D0F341 236273 246947
DF3366 DG3366 DFC366 DGC366 Stainless Steel Santoprene Santoprene D0F366 236273 246947
DF3377 DG3377 DFC377 DGC377 Stainless Steel Buna Buna D0F377 236273 246947
DF3525 DG3525 DFC525 DGC525 TPE Acetal TPE D0F525 236273 246947
DF3555 DFC555 TPE TPE TPE D0F555 236273 246947
DF3666 DG3666 DFC666 DGC666 Santoprene Santoprene Santoprene D0F666 236273 246947
DF3777 DG3777 DFC777 DGC777 Buna Buna Buna D0F777 236273 246947
DF3888 DG3888 DFC888 DGC888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0F888 236273 246947
DF3GGG DG3GGG DFCGGG DGCGGG Geolast Geolast Geolast D0FGGG 236273 246947
DF3911 DG3911 DFC911 DGC911 Polypropylene PTFE PTFE D0F911 236273 246947
DF3977 DG3977 DFC977 Polypropylene Buna Buna D0F977 236273 246947
Stainless Steel DF4311 DG4311 DFD311 DGD311 Stainless Steel PTFE PTFE D0F311 236273 246947
DF4341 DFD341 Stainless Steel Hardened SST PTFE D0F341 236273 246947
DF4366 DG4366 DFD366 DGD366 Stainless Steel Santoprene Santoprene D0F366 236273 246947
DF4377 DG4377 DFD377 DGD377 Stainless Steel Buna Buna D0F377 236273 246947
DF4525 DFD525 TPE Acetal TPE D0F525 236273 246947
DF4666 DG4666 DFD666 DGD666 Santoprene Santoprene Santoprene D0F666 236273 246947
DF4777 DG4777 DFD777 DGD777 Buna Buna Buna D0F777 236273 246947
DF4888 DG4888 DFD888 DGD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0F888 236273 246947
DF4GGG DG4GGG DFDGGG DGDGGG Geolast Geolast Geolast D0FGGG 236273 246947
DF4911 DFD911 Polypropylene PTFE PTFE D0F911 236273 246947
Ductile DF6311 DFF311 Stainless Steel PTFE PTFE D0F311 236273 246947
DF6366 DFF366 Stainless Steel Santoprene Santoprene D0F366 236273 246947
DF6441 DFF441 Hardened SST Hardened SST PTFE D0F441 236273 246947
DF6466 DG6466 DFF466 DGF466 Hardened SST Santoprene Santoprene D0F466 236273 246947
DF6525 DFF525 TPE Acetal TPE D0F525 236273 246947
DF6666 DG6666 DFF666 DGF666 Santoprene Santoprene Santoprene D0F666 236273 246947
DF6A11 DFFA11 PVDF PTFE PTFE D0FA11 236273 246947
DF6A88 DFFA88 PVDF Fluoroelastomer Fluoroelastomer D0FA88 236273 246947
DF6GGG DG6GGG DFFGGG DGFGGG Geolast Geolast Geolast D0FGGG 236273 246947
Corrosion Resistant Pumps with Stainless Steel Center Section
Stainless Steel DV4311 DVD311 Stainless Steel PTFE PTFE D0F311 236273 246947
DV4377 DVD377 Stainless Steel Buna Buna D0F377 236273 246947
DV4388 DVD388 Stainless Steel Fluoroelastomer Fluoroelastomer D0F388 236273 246947
DV4666 DVD666 Santoprene Santoprene Santoprene D0F666 236273 246947
DV4888 DVD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0F888 236273 246947
DV4911 DVD911 Polypropylene PTFE PTFE D0F911 236273 246947
*Requires CycleFlo or external valve control. ** Air control includes air regulator and filter with gauge. *** Also available in Extended Height version; use DFH or DFG designations

34
process equipment catalog
 Husky 2150 Metal Pumps

Technical Specifications

Husky 2150 Metal Pumps Aluminum Stainless Steel Ductile Iron

Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa)
Maximum free flow delivery* 150 gpm (568 lpm) 150 gpm (568 lpm) 150 gpm (568 lpm)
Maximum pump speed 145 cpm 145 cpm 145 cpm
Displacement per cycle** 1.03 gallon (3.90 liter) 1.03 gallon (3.90 liter) 1.03 gallon (3.90 liter)
Maximum suction lift (DF3666) 20 ft (6.1 m) dry 20 ft (6.1 m) dry 20 ft (6.1 m) dry
Maximum size pumpable solids 0.25 in (6.3 mm) 0.25 in (6.3 mm) 0.25 in (6.3 mm)
Maximum diaphragm operating tem-
perature*** 220°F (104.4°C) 220°F (104.4°C) 220°F (104.4°C)
PTFE 180°F (82.2°C) 180°F (82.2°C) 180°F (82.2°C)
Santoprene 180°F (82.2°C) 180°F (82.2°C) 180°F (82.2°C)
Buna-N 150°F (65.5°C) 150°F (65.5°C) 150°F (65.5°C)
TPE 250°F (121.1°C) 250°F (121.1°C) 250°F (121.1°C)
Fluoroelastomer 150°F (65.5°C) 150°F (65.5°C) 150°F (65.5°C)
Geolast
Typical sound level at 70 psi 78 dBa 78 dBa 78 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 175 scfm (4.9 m3/min) 175 scfm (4.9 m3/min) 175 scfm (4.9 m3/min)
Air pressure operating range 20 to 120 psi 20 to 120 psi 20 to 120 psi
(1.4 to 8.4 bar, (1.4 to 8.4 bar, (1.4 to 8.4 bar,
0.14 to 0.84 MPa) 0.14 to 0.84 MPa) 0.14 to 0.84 MPa)
Air inlet size 1/2 npt(f) 1/2 npt(f) 1/2 npt(f)
Fluid inlet & outlet size**** 2 in (51 mm) npt(f) 2 in (51 mm) npt(f) 2 in (51 mm) npt(f)
Weight 58 lb (26.3 kg) 111 lb (50 kg) 130 lb (59 kg)
62 lb (28.1 kg) - Extended
Weight with stainless steel center n/a 134 lb (60 kg) n/a
section
Instruction manual 308368 308368 308368
* Flow rates are with muffler and do not vary based on diaphragm material
** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type
*** Actual pump performance may be affected by prolonged usage at temperature

35
process equipment catalog
 Husky 2150 Metal Pumps

Performance Charts Dimensions

Husky 2150 Performance 8.39 in 9.06 in
120 150 (213 mm) (230 mm)
(8.4, 0.84) (4.2)
A
A
100 125
FluID outlet PreSSure psi (bar, MPa)

(7, 0.7) (3.5) 1/2 npt(f)

B B Air Inlet

aIr conSumPtIon scfm (m3/min)

80 100
(5.5, 0.55) (2.8) 19.37 in
C (492 mm)
C 23.0 in
60 75 (584 mm)
(4.1, 0.41) (2.1)
12.3 in 21.37 in
40 50 (312.5 mm) (543 mm)
(2.8, 0.28) D (1.4)

20 25
D
(1.4, 0.14) (0.7)
3/4 npt(f)
0 Air Exhaust
gpm 0 20 40 60 80 100 120 140 160 (muffler included) 6.0 in (152.5 mm) 2.0 in
(lpm) (76) (152) (227) (303) (379) (454) (531) (606) (51 mm)
17.45 in (443 mm)
FluiD FlOW
(Pump tested in water with inlet submerged

aIr PreSSure legenD 6.25 in Port Diameter:

(159 mm) 2 in (51 mm)
A = at 120 psi (8.4 bar, 0.84 MPa) Air Consumption
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow
C = at 70 psi (4.8 bar, 0.48 MPa)
D = at 40 psi (2.8 bar, 0.28 MPa)

0.38 in
(9.5 mm)

6.0 in (152.5 mm)

12.5 in (317.5 mm)

Typical System Drawings

Husky 2150 Above Ground Gravity Feed

36
process equipment catalog
 Husky 3300 Plastic Pumps
Air-Operated Double Diaphragm

NEW! Husky 3300 Selector Tool

To order a Husky 3300, use the online selector tool at
www.graco.com/process or contact your distributor.

Pump Configuration
Number

NOTE: Options for seats, check balls,

diaphragms, and seals vary.

Example of Product Selector Tool on www.graco.com/process

Pump Configurations
Pump Center Section and
(3 inch ports, 300 gpm) Air Valve Material Air Valve/Monitoring Fluid Covers and Manifolds
3300P ✝ Aluminum A01A Standard Diaphragms P1 Polypropylene, center flange
Polypropylene A01G Overmolded Diaphragms
Polypropylene ✝ P01A Standard Diaphragms
P01G Overmolded Diaphragms
✝: See ATEX Certifications below.

Check Valve Seats Check Valve Balls Diaphragm Manifold and Seat Seals
AC Acetal AC Acetal BN Buna-N --- Models with Buna-N,
AL Aluminum BN Buna-N CO Polychloroprene Overmolded FKM Fluoroelastomer
or TPE seats do not use
BN Buna-N CR Polychloroprene Standard CR Polychloroprene o-rings.
FK FKM Fluoroelastomer CW Polychloroprene Weighted FK FKM Fluoroelastomer BN Buna
GE Geolast® FK FKM Fluoroelastomer GE Geolast PT PTFE
PP Polypropylene GE Geolast PO PTFE/EPDM Overmolded
SP Santoprene® PT PTFE PT PTFE/Santoprene Two-Piece
SS 316 Stainless Steel SP Santoprene SP Santoprene
TP TPE TP TPE TP TPE

ATEX Certifications
† Pumps with polypropylene fluid or center sections are not
ATEX certified.

37
process equipment catalog
 Husky 3300 Plastic Pumps

Popular Models
Air Valve
Materials for Materials for Materials for Replacement Diaphragm O-Ring
Material Part Number Seats Balls Diaphragms Kit Seat Kit Ball Kit Kit Kit
Polypropylene 652404 Polypropylene PTFE 2 pc PTFE 24K857 24K933 24K943 24K905 24K927
Polypropylene 652400 Polypropylene Santoprene Santoprene 24K857 24K933 24K944 24K902 24K927
Polypropylene 652423 Santoprene Santoprene Santoprene 24K857 24K934 24K944 24K902 24K927
Polypropylene 652414 Stainless Steel PTFE 2 pc PTFE 24K857 24K935 24K943 24K905 24K927
Polypropylene 652402 Polypropylene FKM FKM 24K857 24K933 24K945 24K903 24K927

Technical Specifications

Husky 3300 Plastic Pumps Polypropylene

Maximum fluid working pressure 100 psi (7.0 bar, 0.7 MPa)
Maximum free flow delivery*
Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) 280 gpm (1,059 lpm)
Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) 260 gpm (984 lpm)
Maximum pump speed*
Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) 97 cpm
Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) 130 cpm
Maximum suction lift * 8 ft (2.4 m) dry
(varies widely based on ball/seat selection and wear, operating 28 ft (8.5 m) wet
speed, material properties, and other variables)
Maximum size pumpable solids 0.5 in (13 mm)
Noise (dBa)***
Sound Power at 50 psi (3.4 bar) and 50 cpm 92 dBa
Sound Power at 120 psi (8.3 bar) and full flow 99 dBa
Sound Pressure at 50 psi (3.4 bar) and 50 cpm 86 dBa
Sound Pressure at 120 psi (8.3 bar) and full flow 93 dBa
Maximum air consumption 275 scfm (7.8 m3/min.)
Air pressure operating range 20 to 100 psi
(1.4 to 7.0 bar, 0.14 to 0.7 MPa)
Air inlet size 3/4 npt(f)
Fluid inlet/outlet 3 in (76.2 mm) ANSI/DIN flange
Weight 200 lb (91 kg)
Instruction manual 3A0410
Repair/parts manual 3A0411
* Maximum values with water as media at ambient temperature. Water level is approximately 3 feet above pump inlet.
** Startup pressures and displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type.
*** Sound power measured per ISO-9614-2. Sound pressure was tested 3.28 ft (1 m) from equipment.
*** Actual pump performance may be affected by prolonged usage at temperature

38
process equipment catalog
 Husky 3300 Plastic Pumps
Polypropylene Pump Dimensions
Performance Charts Dimensions

Husky 3300 Performance

29.12 in.
(74.0 cm)
Approxx. Cycles per Minute 14.56 in.
(37.0 cm)
125 17.2 34.5 51.7 69.0 86.2 375
FLUID OUTLET PRESSURE psi (bar, MPa)

(8.6, 0.86) (10.6)

A

AIR CONSUMPTION scfm (m3/min)

100 A 300
(7, 0.69) B (8.5)
B
75 225
(5.2, 0.52) (6.4)
C Air Inlet
C (opposite side
50 150 from muffler) 41.40 i
(3.4, 0.34) (4.2) (105.2 c
D
25 D 75
(1.7, 0.17) (2.1)
26.69 in.
0 (67.8 cm)
gpm 0 50 100 150 200 250 300
(lpm) (189) (379) (568) (757) (946) (1136)
FLUID FLOW
(Pump tested in water with inlet submerged)

AIR PRESSURE LEGEND

19.31 in.
A = at 125 psi (8.3 bar, 0.83 MPa) Air Consumption (49.0 cm)
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow
C = at 70 psi (4.8 bar, 0.48 MPa)
8.30 in.
D = at 40 psi (2.8 bar, 0.28 MPa) (21.1 cm)
13.00 in.
(33.0 cm) 16.58 in.
18.87 in.
(42.1 cm)
(47.9 cm)

Typical System Drawings

39
process equipment catalog
 Husky 3300 Metal Pumps
Air-Operated Double Diaphragm

NEW! Husky 3300 Selector Tool

To order a Husky 3300, use the online selector tool at
www.graco.com/process or contact your distributor.

Pump Configuration
Number

NOTE: Options for seats, check balls, Example of Product Selector Tool on www.graco.com/process

diaphragms, and seals vary.

Pump Configurations

Pump Center Section and

(3 inch ports, 300 gpm) Air Valve Material Air Valve/Monitoring Fluid Covers and Manifolds
3300A ★ Aluminum A01A Standard Diaphragms A1 Aluminum, center flange, npt
Aluminum Optional FKM seals with A2 Aluminum, center flange, bspt
3300S ★ A01E
Standard Diaphragms
Stainless Steel A01G Overmolded Diaphragms S1 Stainless steel, center flange, npt
Polypropylene ✝ P01A Standard Diaphragms S2 Stainless steel, center flange, bspt
P01G Overmolded Diaphragms
★: See ATEX Certifications below.

Check Valve Seats Check Valve Balls Diaphragm Manifold and Seat Seals
AC Acetal AC Acetal BN Buna-N --- Models with Buna-N,
AL Aluminum BN Buna-N CO Polychloroprene Overmolded FKM Fluoroelastomer
or TPE seats do not use
BN Buna-N CR Polychloroprene Standard CR Polychloroprene o-rings.
FK FKM Fluoroelastomer CW Polychloroprene Weighted FK FKM Fluoroelastomer BN Buna
GE Geolast® FK FKM Fluoroelastomer GE Geolast PT PTFE
PP Polypropylene GE Geolast PO PTFE/EPDM Overmolded
SP Santoprene® PT PTFE PT PTFE/Santoprene Two-Piece
SS 316 Stainless Steel SP Santoprene SP Santoprene
TP TPE TP TPE TP TPE

ATEX Certifications
★ 3300A (aluminum) and 3300S (stainless steel) pumps with aluminum center sections are certified:

II 2 GD c IIC T4

40
process equipment catalog
 Husky 3300 Metal Pumps

Popular Models
Air Valve
Materials for Materials for Materials for Replacement Diaphragm O-Ring
Material Part Number Seats Balls Diaphragms Kit Seat Kit Ball Kit Kit Kit
Aluminum 652002 TPE Acetal TPE 24K855 24K932 24K937 24K901 24K909
Aluminum 652046 Geolast Geolast Geolast 24K855 24K931 24K939 24K900 24K909
Aluminum 652021 Stainless Steel PTFE 2 pc PTFE 24K855 24K935 24K943 24K905 24K927
Aluminum 652081 Acetal PTFE 2 pc PTFE 24K855 24K928 24K943 24K905 24K927
Aluminum 652036 Santoprene Santoprene Santoprene 24K855 24K934 24K944 24K902 24K909
Stainless Steel 652804 Stainless Steel PTFE 2 pc PTFE 24K857 24K935 24K943 24K905 24K927
Stainless Steel 652812 Santoprene Santoprene Santoprene 24K857 24K934 24K944 24K902 24K927

Technical Specifications

Husky 2150 Metal Pumps Aluminum Stainless Steel

Maximum fluid working pressure
with Aluminum Center Section 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa)
with Polypropylene Center Section 100 psi (7.0 bar, 0.7 MPa)
Maximum free flow delivery*
Standard diaphragms at 125 psi (8.6 bar, 0.86 MPa) 300 gpm (1,135 lpm) 300 gpm (1,135 lpm)
Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) 280 gpm (1,059 lpm) 280 gpm (1,059 lpm)
Overmolded diaphragms at 125 psi (8.6 bar, 0.86 MPa) 270 gpm (1,022 lpm) 270 gpm (1,022 lpm)
Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) 260 gpm (984 lpm) 260 gpm (984 lpm)
Maximum pump speed*
Standard diaphragms at 125 psi (8.6 bar, 0.86 MPa) 103 cpm 103 cpm
Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) 97 cpm 97 cpm
Overmolded diaphragms at 125 psi (8.6 bar, 0.86 MPa) 135 cpm 135 cpm
Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) 130 cpm 130 cpm
Maximum suction lift * 8 ft (2.4 m) dry 8 ft (2.4 m) dry
(varies widely based on ball/seat selection and wear, 28 ft (8.5 m) wet 28 ft (8.5 m) wet
operating speed, material properties, and other variables)
Maximum size pumpable solids 0.5 in (13 mm) 0.5 in (13 mm)
Noise (dBa)***
Sound Power at 50 psi (3.4 bar) and 50 cpm 92 dBa 92 dBa
Sound Power at 120 psi (8.3 bar) and full flow 99 dBa 99 dBa
Sound Pressure at 50 psi (3.4 bar) and 50 cpm 86 dBa 86 dBa
Sound Pressure at 120 psi (8.3 bar) and full flow 93 dBa 93 dBa
Maximum air consumption
with Aluminum Center Section 335 scfm (9.5 m3/min.) 335 scfm (9.5 m3/min.)
with Polypropylene Center Section 275 scfm (7.8 m3/min.)
Air pressure operating range
with Aluminum Center Section 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa)
with Polypropylene Center Section 20 to 100 psi (1.4 to 7.0 bar, 0.14 to 0.7 MPa)
Air inlet size 3/4 npt(f) 3/4 npt(f)
Fluid inlet 3 in (76.2 mm) npt or bspt with ANSI/DIN flange 3 in (76.2 mm) npt or bspt
Weight 150 lb (68 kg) 255 lb (116 kg)
Instruction manual 3A0410 3A0410
Repair/parts manual 3A0411 3A0411
* Maximum values with water as media at ambient temperature. Water level is approximately 3 feet above pumpinlet.
** Startup pressures and displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type.
*** Sound power measured per ISO-9614-2. Sound pressure was tested 3.28 ft (1 m) from equipment.

41
process equipment catalog
 Husky 3300 Metal Pumps

Performance Charts

Husky 3300 Performance

Approxx. Cycles per Minute

125 17.2 34.5 51.7 69.0 86.2 375
FLUID OUTLET PRESSURE psi (bar, MPa)

(8.6, 0.86) (10.6)

A

AIR CONSUMPTION scfm (m3/min)

100 A 300
(7, 0.69) B (8.5)
B
75 225
(5.2, 0.52) (6.4)
C
C
50 150
(3.4, 0.34) (4.2)
D
25 D 75
(1.7, 0.17) (2.1)

0
gpm 0 50 100 150 200 250 300
(lpm) (189) (379) (568) (757) (946) (1136)
FLUID FLOW
(Pump tested in water with inlet submerged)

AIR PRESSURE LEGEND

A = at 125 psi (8.3 bar, 0.83 MPa) Air Consumption
B = at 100 psi (7 bar, 0.7 MPa) Fluid Flow
C = at 70 psi (4.8 bar, 0.48 MPa)
D = at 40 psi (2.8 bar, 0.28 MPa)

Typical System Drawings

42
process equipment catalog
 Husky 3300 Metal Pumps
Aluminum Pump Dimensions Stainless Steel Pump Dimensions

Dimensions
Aluminum Pump Dimensions Stainless Steel Pump Dimensions
Aluminum Stainless Steel
24.08 in. 24.68 in.
(61.2 cm) (62.7 cm)
12.34 in.
12.04 in. (31.3 cm)
(30.6 cm)

Air Inlet
(opposite side 23.8 i
Air Inlet from muffler)
(60.5 c
(opposite side
from muffler) 27.88 in.
(70.8 cm)
32.56 in.
24.50 in. (82.7 cm)
19.38 in.
(62.2 cm)
28.63 in. (49.2 cm)
19.70 in. (72.7 cm)
(50.0 cm)
4.5
(11.4

4.13 in.
(10.5 cm)

16.83 in.
16.56 in. (42.7 cm)
(42.1 cm)

8.25 in.
8.25 in. (21.0 cm)
(21.0 cm)
13.0 in.
13.00 in. 19.05 in.
16.5 in. 18.8 in. (33.0 cm)
(33.0 cm) (48.4 cm)
(41.9 cm) (47.8 cm)
16.5 in.
(41.9 cm)

43
process equipment catalog
 Title Transfer Pump Packages
Husky
Subhead
55 Gallon (208 liter) Size

Ordering Information

Pump Components Drum Kit Components

Package Pump Pump seats balls Diaphragms drum kit tube tube part easy out seal and
Number Type number* number** material number mounting base

233051 Husky 515 241565 Polypropylene PTFE PTFE 233045 Polypropylene 196096 233073
Polypropylene
233052 Husky 515 241564 Acetal PTFE PTFE 233047 Stainless Steel 196094 233074
Acetal
233053 Husky 515 241564 Acetal PTFE PTFE 233046 Aluminum 195095 233074
Acetal
233054 Husky 716 243305 Acetal Santoprene Santoprene 233046 Aluminum 196095 233074
Aluminum
233055 Husky 716 243306 Acetal Buna Buna 233046 Aluminum 196095 233074
Aluminum
233056 Husky 716 243307 Acetal PTFE PTFE 233046 Aluminum 196095 233074
Aluminum
233057 Husky 716 D54311 Stainless PTFE PTFE 233048 Stainless Steel 196094 233076
Stainless Steel Steel

Accessories
246946 Air Regulator/Filter
208536 Air Line Quick Coupler
169970 Quick Coupler Nipple

44
process equipment catalog
 Husky Transfer Pump Packages

Technical Specifications
Acetal Polypropylene Aluminum Stainless Steel
Husky 55 gal Transfer Pump Husky 515 Husky 515 Husky 716 Husky 716
Dimensions
Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa)
Maximum free flow delivery* 12 gpm (57 lpm) 12 gpm (57 lpm) 14 gpm (61 lpm) 14 gpm (61 lpm)
Maximum pump speed 400 cpm 400 cpm 400 cpm 400 cpm
Displacement per cycle** 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter)
Maximum size pumpable solids 0.094 in (2.5 mm) 0.094 in (2.5 mm) 0.094 in (2.5 mm) 0.094 in (2.5 mm)
Typical sound level at 70 psi 67 dBa 67 dBa 67 dBa 67 dBa
(4.9 bar, 0.49 MPa) air @ 125 cpm
Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min)
Air pressure operating range 25 to 100 psi 25 to 100 psi 25 to 100 psi 25 to 100 psi
(1.8 to 7 bar, 0.18 to 0.7 MPa) (1.8 to 7 bar, (1.8 to 7 bar, (1.8 to 7 bar,
0.18 to 0.7 MPa) 0.18 to 0.7 MPa) 0.18 to 0.7 MPa)
Air inlet size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) 1/4 npt(f)
Air exhaust port size 3/8 npt(f) 3/8 npt(f) 3/8 npt(f) 3/8 npt(f)
Fluid inlet size 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f)
Fluid outlet size 1/2 and 3/4 npt(f) 1/2 and 3/4 npt(f) 3/4 npt(f) 3/4 npt(f)
Wetted parts (fluid covers and groundable acetal, PTFE polypropylene, PTFE aluminum, stainless steel, stainless steel, PTFE
manifolds) PTFE, zinc-plated steel
Pump weight 7.8 lb (3.5 kg) 6.5 lb (2.9 kg) 8.5 lb (3.9 kg) 18 lb (8.2 kg)
Drum package weight 12.3 lb (5.6 kg) 14.3 lb (6.5 kg) 10.5 lb (4.8 kg) 13.0 lb (5.9 kg) 27.5 lb (12.5 kg)
tube material aluminum stainless steel polypropylene aluminum stainless steel
Drum kit weight 4.5 lb (2.0 kg) 6.5 lb (2.9 kg) 4.0 lb (1.8 kg) 4.5 lb (2.0 kg) 6.5 lb (2.9 kg) 9.5 lb (4.3 kg)
easy-out seal material aluminum stainless steel polypropylene acetal acetal stainless steel
Drum package instruction manual 309116 309116 309116 309116
Instruction manual 308981 308981 308981 308981

* Flow rates are with muffler and do not vary based on diaphragm material
** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type

45
process equipment catalog
 Husky Transfer Pump Packages

Dimensions

8.5 in. 8.5 in.

(216 mm) (216 mm)

Adjustable from Adjustable from Adjustable from

2.6 in. (66 mm) to 2.6 in. (66 mm) to 6.9 in. 2.6 in. (66 mm) to
6.8 in.
5.1 in. (130 mm) 5.1 in. (130 mm) (175 mm) 5.1 in. (130 mm)
(173 mm)

Adjustable from Adjustable from

31.5 in. (800 mm) to 31.5 in. (800 mm) to
34.0 in. (864 mm) 34.0 in. (864 mm)
Adjustable from
31.5 in. (800 mm) to
34.0 in. (864 mm)

Poly, Acetal and Stainless Steel Pumps Overall height depends on pump.
Aluminum Pumps See page 12 or 15 for pump dimensions

46
process equipment catalog
 Husky Transfer Pump Packages
Pump and Agitator Packages

Ordering Information Technical Specifications

Husky 515 on Twistork Agitator
part Husky 55 gal (200 l)
Maximum air input pressure 100 psi (7 bar)
number Dispensing package
Maximum fluid output pressure 100 psi (7 bar)
Maximum siphon flow rate
231418 Husky 515 acetal pump 241564, with 100 cps material 12 gpm (45.4 lpm)
stainless steel drum cover 238283,
with 1000 cps material 1.2 gpm (4.54 lpm)
heavy-duty agitator 238157,
air-powered drum cover elevator Air inlet Quick-coupler, nipple (pin)
237746, air controls, hose and Fluid outlet size 3/4 npt(f)
dispense valve Maximum recommended agitator speed 800 rpm
Agitator air consumption
231419 Husky 515 acetal pump, stainless
at 400 rpm 2.5 scfm (0.07 m3 /min)
steel drum cover, heavy-duty
agitator, drum cover elevator at 800 rpm 5.7 scfm (0.16 m3 /min)
Pump air consumption approximately 12 scfm
at 12 gpm (45.4 lpm) (0.34 m3 /min)
part Husky twistork® package Maximum operating temperature 150º F (66º C)
number Weight 32 lb (14.5 kg)
Maximum noise level* 85 dB(A)
Instruction manual 308656
238859 Husky 515 D52911 Polypropylene

Service and Technical Data

pump mounted on Twistork * Tested to CAGI-PNEUROP–1969
238860 Husky 515 D52911 Acetal pump ** See the individual component instruction manuals for service instructions and
technical data for the Husky 55 gal (200 l) Dispensing Packages.
mounted on Twistork
See the individual component instruction manuals for service instructions and technical data.

Dimensional Drawing
Dimensions
NOTE: See individual component instruction manuals for dimensions
of agitator,Package
Husky 55 gal Dispensing pump, elevator, siphon kit, and drum cover. Husky Twistork Package

Service and Technical Data

See the individual component instruction manuals for service instructions and technical data.

height of unit from

Dimensional
base to top of pump
when elevator is raised
Drawing Elevator Base
Mounting Hole Layout
NOTE: See individual component instruction manuals for dimensions
of agitator, pump, elevator, siphon kit, and drum cover.

95 in.
(2413 mm)
8.88 in.
(225.6 mm)

height of unit from

base to top of pump Elevator Base
when elevator is raised Mounting Hole Layout

5.5 in.
(140 mm) 0.56-in.
95 in. (14.2 mm)
(2413 mm) holes
8.88 in.
(225.6 mm)

57 in.
(1448 mm)

5.5 in.
(140 mm) 0.56-in.
(14.2 mm)
holes
9294A

57 in.
(1448 mm)
47
process equipment catalog
 Husky Pump Accessories
Air-Operated Double Diaphragm

Husky 205 Accessories Part Number

AIR CONTROLS
Regulator / Filter Assembly 1/4” npt(f) (6.35 mm) 246946
Quick Connect Air Coupler 1/4” npt (6.35 mm) 208536
Quick Connect Air Nipple 1/4” npt (6.35 mm) mbe 169970
Air Shut Off Valve 1/4” npt (6.35mm), bleed type, relieves trapped air downline of valve 110223
Air Runaway Valve (stops pump from cavitating when empty) 224040
Air Muffler (comes with pump) 114174
55-GALLON SIPHON KITS
Polypropylene Suction Kit (includes siphon hose, tube and connectors) 239142
Acetal Suction Kit (includes siphon hose, tube and connectors) 239143
PVDF Suction Kit (includes siphon hose, tube and connectors) 239144
REMOTE PUMP CONTROLLERS
CycleFlo (cpm rate and batch control) 120v 195264
CycleFlo (cpm rate and batch control) 240v 196706
CycleFlo II (rate controller with solenoid valve) 120v 195265

Husky 307 Accessories

AIR CONTROLS
Regulator / Filter Assembly 1/4” npt(f) (6.35 mm) 246946
Quick Connect Air Coupler 1/4” npt (6.35 mm) 208536
Quick Connect Air Nipple 1/4” npt (6.35 mm) mbe 169970
Air Shut Off Valve 1/4” npt (6.35 mm), bleed type, relieves trapped air downline of valve 110223
Air Runaway Valve (stop pump from cavitating when empty) 224040
Air Muffler (comes with pump) 112933
55-GALLON SIPHON KITS
Polypropylene Suction Kit (includes siphon hose, tube and connectors) 235502
Acetal Suction Kit (includes siphon hose, tube and connectors) 235500
REMOTE PUMP CONTROLLERS
Husky 307 pumps are not equipped to run in remote mode N/A
SPLIT MANIFOLD KITS
 y varying the manifold kits, pumps can be configured in different ways (one inlet and two outlets, two inlets and one outlet, and
B
two inlets and two outlets, etc), allowing for system flexibility. Pumps need to be ordered separately. One kit is required for each
side (top or bottom). See 308439 for details.
Acetal Split Manifold Kit 237211
Polypropylene Split Manifold Kit 237210
Rubber Foot Kit 236452
Wall Mounting Bracket
Wall mounting bracket for Husky 307 pumps 224835

48
process equipment catalog
 Husky Pump Accessories

Husky 515 and Husky 716 Accessories Part Number

AIR CONTROLS
Regulator / Filter Assembly 1/4” npt(f) (6.35 mm) 246946
Quick Connect Air Coupler 1/4” npt (6.35 mm) 208536
Quick Connect Air Nipple 1/4” npt (6.35 mm) mbe 169970
Air Shut Off Valve 1/4” npt (6.35 mm), bleed type, relieves trapped air downline of valve 110223
Air Runaway Valve (stop pump from cavitating when empty) 224040
Air Muffler (comes with pump) 112933
Center Section Conversion Kit (converts an old style Husky 715 to a Husky 515/716) 241631
Center Section Conversion Kit (converts an old remote style Husky 715 to a Husky 515/716) 241664
55-GALLON SIPHON KITS
 rum Kit (includes “easy out seal” mounting base and siphon tube). Best used with a wall mounted Husky 515 or 716 model.
D
Pump models can be mounted to base, but may require opening bottom inlet. See 309116 for details.
Mounting Base with a Polypropylene Siphon Tube 233045
Mounting Base with a Aluminum Siphon Tube 233046
Mounting Base with a Stainless Steel Siphon Tube (used with non sst pumps) 233047
Mounting Base with a Stainless Steel Siphon Tube (for sst pump only) 233048
REMOTE PUMP CONTROLLERS
CycleFlo (cpm rate and batch control) 120v 195264
CycleFlo (cpm rate and batch control) 240v 196706
CycleFlo II (rate controller with solenoid valve) 120v 195265
SPLIT MANIFOLD KITS (Husky 515 only)
 y varying the manifold kits, pumps can be configured in different ways (one inlet and two outlets, two inlets and one outlet, and
B
two inlets and two outlets, etc), allowing for system flexibility. Pumps need to be ordered separately. See manual 308951 for
details.
Polypropylene Inlet Manifolds 241240
Polypropylene Outlet Manifolds 241243
Acetal Inlet Manifolds 241241
Acetal Outlet Manifolds 241244
PVDF Inlet Manifolds 241242
PVDF Outlet Manifolds 241245
Wall Mounting Bracket
Wall mounting bracket for Husky 515 & Husky 716 pumps 224835
MISCELLANEOUS ACCESSORIES
Duckbill Replacement Parts (urethane) for 515 and 716 Husky Pumps 239754
SURGE SUPPRESSORS
S urge suppressors are designed to reduce the pulsation caused during pump changeover. The suppressor construction is generally
closely matched with the pump’s material (Stainless Steel with Stainless Steel, Acetal with Aluminum, etc.) and are available in either
an adjustable or automatic version. See 308703 for details.
Automatic Husky 750, 3/4” (19.05 mm)
Polypropylene (wetted bottom and top housings) with a Buna N bladder 239096
with PTFE bellows 239121
with a Fluoroelastomer bladder 239122

49
process equipment catalog
 Husky Pump Accessories

Husky 515 and Husky 716 Accessories (continued) Part Number

SURGE SUPPRESSORS (continued)
Stainless Steel (wetted bottom and top housings) with a Buna N bladder 239095
with PTFE bellows 239123
with a Fluoroelastomer bladder 239124
Acetal (wetted bottom and top housings) with a Buna N bladder 239094
with PTFE bellows 239125
Adjustable Husky 750, 3/4” (19.05 mm)
Polypropylene (wetted bottom and top housings) with a Buna N bladder 239091
with PTFE bellows 239129
with a Fluoroelastomer bladder 239130
Stainless Steel (wetted bottom and top housings) with a Buna N bladder 239090
with PTFE bellows 239131
with a Fluoroelastomer bladder 239132
Acetal (wetted bottom and top housings) with a Buna N bladder 239089
with PTFE bellows 239133
PTFE/EPDM Overmolded Diaphragms
Industrial upgrade kits – includes new airside diaphragm plate
Upgrade kit for 0.5 in (1.27 cm) and 0.75 in (1.905 cm) pump 24N321
LEAK DETECTOR
Leak detectors are designed to shut off the pump in the event a diaphragm fails. The leaking material flows out the air section and
is captured by the leak detector reservoir. Once the reservoir is filled, a signal is sent that would shut off the pump. These detectors
should only be used when a massive failure is allowed.
Polypropylene Housings with PVC Wetted Parts 239080
Shut Off Valve Kit (used in conjunction with 239080) 113870

Husky 1050, 1590, 2150 Accessories

AIR CONTROLS
Regulator / Filter Assembly 1/2” npt(f) (12.7 mm) 246947
Quick Connect Air Coupler 1/2” npt (12.7 mm) 110199
Quick Connect Air Nipple 1/2” npt (12.7 mm) mbe 110196
Air Shut Off Valve 1/2” npt (12.7mm), bleed type, relieves trapped air downline of valve 110225
Air Runaway Valve (stop pump from cavitating when empty) 224040
Air Muffler (comes with pump) 1050 pumps 24D642
Air Muffler (comes with pump) 1590 and 2150 pumps 102656
Center Section Conversion Kit (converts an aluminum center section to sst. Includes air covers).
Husky 1590 246451
Husky 2150 246452
55-GALLON SIPHON KIT
Siphon kit is used for drawing fluids from 55-gallon sized containers, through a 2” bung opening.
Kit comes with carbon steel tube, 8’ (2.44m) polyethylene hose and couplings 222916
REMOTE PUMP CONTROLLERS
CycleFlo (cpm rate and batch control) 120v 195264
CycleFlo (cpm rate and batch control) 240v 196706
CycleFlo II (rate controller with solenoid valve) 120v 195265
Dual Inlet Manifold
Aluminum Husky 1050 only 24D205
Conversion Kits
Remote Valve Conversion Kit for Aluminum Husky 1050 only 24D037
Remote Valve Conversion Kit for Polypropylene Husky 1050 only 24D038
Remote Valve Conversion Kit for Conductive Polypropylene Husky 1050 only 24D039

50
process equipment catalog
 Husky Pump Accessories

Husky 1050, 1590, 2150 Accessories (continued) Part Number

SURGE SUPPRESSORS
Surge suppressors are designed to reduce the pulsation caused during pump changeover. The suppressor construction is generally closely matched
with the pump’s material (Stainless Steel with Stainless Steel, Acetal with Aluminum, etc.) and are available in either an adjustable or automatic
version. See 308703 for details.
Automatic Husky 2000, 2 in (50.8 mm)
Polypropylene (wetted bottom and top housings) with a Buna N bladder 239092
with PTFE bellows 239128
Stainless Steel (wetted bottom and top housings) with a Buna N bladder 239093
with PTFE bellows 239126
with a Fluoroelastomer bladder 239127
Adjustable Husky 2000, 2 in (50.8 mm)
Polypropylene (wetted bottom and top housings) with a Buna N bladder 239087
with PTFE bellows 239136
Stainless Steel (wetted bottom and top housings) with a Buna N bladder 239088
with PTFE bellows 239134
with a Fluoroelastomer bladder 239135
UL PUMPS
For use with leaded and unleaded fuels
Husky 1050 for use with leaded fuel (seat, ball, diaphragm) 647016
Same as 236265, maximum inlet of 50 psi (3.4 bar, 0.3 MPa) 647648
PTFE/EPDM Overmolded Diaphragms
Industrial upgrade kits – includes new airside diaphragm plate
Upgrade kit for 1 inch (2.54 cm) Husky 1040 pump 289224
Upgrade kit for 1 inch (2.54 cm) Husky 1050 pump 24B626
Upgrade kit for 1.5 inch (3.81 cm) pump 289225
Upgrade kit for 2 inch (5.08 cm) pump 289226
LEAK DETECTOR
Leak detectors are designed to shut off the pump in the event a diaphragm fails. The leaking material flows out the air section and is captured by
the leak detector reservoir. Once the reservoir is filled, a signal is sent that would shut off the pump. These detectors should only be used when a
massive failure is allowed.
Polypropylene Housings with PVC Wetted Parts 239080
Shut Off Valve Kit (used in conjunction with 239080) 113870
Wall Mounting Bracket
Wall mounting bracket for Husky 1050 pumps 24C637
MISCELLANEOUS ACCESSORIES
Flange Kits. Used to transition a flanged pump to a npt connection to transition from
a threaded connection to a flange. It is recommended that the flange kit be compatible
with the pump material.
Polypropylene 1 inch (24.14 mm) flange for Husky 1050 D72XXX pumps. 1” ANSI x 1” npt (f) 239005
Stainless Steel 1 inch (24.14 mm) flange for Husky 1050 D71XXX and D74XXX pumps 1” ANSI x 1” npt (f) 239008
PVDF 1 inch (24.14 mm) flange for Husky 1050 D75XXX pump 1” ANSI x 1” npt (f) 239009
Polypropylene 1-1/2 inch (36.84 mm) flange for Husky 1590 DB2XXX pump 1-1/2” ANSI x 1-1/2” (f) 239006
PVDF 1-1/2 inch (36.84 mm) flange for Husky 1590 DB5XXX pump. 1-1/2” ANSI x 1-1/2” (f) 239010
Polypropylene 2 inch (48.28 mm) flange for Husky 2150 DF2XXX pump. 2” ANSI x 2” (f) 239007
PVDF 2 inch (48.28 mm) flange for Husky 2150 DF5XXX pump 2” ANSI x 2” (f) 239011

51
process equipment catalog
 Husky Pump Accessories

Husky 3300 Accessories

AIR CONTROLS
Regulator / Filter Assembly 3/4” npt(f) (19.5 mm) 246948
Quick Connect Air Coupler 3/4” npt (19.5 mm) 110200
Quick Connect Air Nipple 3/4” npt (19.5 mm) mbe 110197
Air Shut Off Valve 3/4” npt (19.5 mm), bleed type, relieves trapped air downline of valve 110226
Air Runaway Valve (stop pump from cavitating when empty) 224040
Air Muffler (comes with pump) 111897
55-GALLON SIPHON KITS
Typically, 3” pumps are not used for emptying 55-gallon containers N/A
REMOTE PUMP CONTROLLERS
Husky 3300 pumps are not equipped to run in remote mode N/A
SPLIT MANIFOLD KITS
There are no Husky 3300 with a split manifold option N/A
SURGE SUPPRESSORS
Surge suppressors are designed to reduce the pulsation caused during pump changeover. The suppressor construction is generally closely matched
with the pump’s material (Stainless Steel with Stainless Steel, Acetal with Aluminum, etc.) and are available either in adjustable or automatic
version. See 308703 for details.
Automatic Husky 2000, 2 in (50.8 mm)
Polypropylene (wetted bottom and top housings) with a Buna N bladder 239092
with PTFE bellows 239128
Adjustable Husky 2000, 2 in (50.8 mm)
Polypropylene (wetted bottom and top housings) with a Buna N bladder 239087
with PTFE bellows 239136

52
process equipment catalog
 EP Series Hose Pumps
Positive Displacement Hose Pumps

Ordering Instructions
Three steps to choosing your pump:
1. Choose your pump size to meet your flow requirement
Use the Performance Charts below to choose your Pump Model.
2. Choose your pump speed range
Using the Selection Charts, go to your Model Number and find
the Gear Ratio for your desired pump speed.
3. Choose your hose & hose barb materials
to meet your material properties
Keep moving down the Selection Charts to select your hose
material and your hose barb material.

Step 1: Performance Charts & Technical Specifications

Pump Model EP2006 EP2010 EP2013

Maximum flow (130 rpm) 0.5 gpm (2.0 lpm) 1.2 gpm (4.4 lpm) 2.1 gpm (7.9 lpm)
Capacity (flow per revolution) 0.004 gal/rev (0.015 l/rev) 0.009 gal/rev (0.034 l/rev) 0.016 gal/rev (0.06 l/rev)
Maximum discharge pressure 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar)
Hose inner diameter 6 mm 10 mm 13 mm
Port size 1/2 in male NPT 1/2 in male NPT 1/2 in male NPT

EP2006 Performance EP2010 Performance EP2013 Performance

0.75 1.25 2.5
3/4 Hp

1.00 2.0

FLOW (gpm)

MOTOR Hp
FLOW (gpm)

FLOW (gpm)
MOTOR Hp

MOTOR Hp
0.50
0.75 1.5

3/4 Hp
3/4 Hp

0.50 1.0
1/2 Hp

0.25
0.25 0.5

0.00 0.00 0.0

0 20 40 60 80 100 120 0 20 40 60 80 100 120 0 20 40 60 80 100 120

PUMP SPEED (rpm) PUMP SPEED (rpm) PUMP SPEED (rpm)

Pump Model EP3016 EP3019 EP4025 EP4029

Maximum flow (130 rpm) 4.6 gpm (17.2 lpm) 6.2 gpm (23.6 lpm) 14.3 gpm (54.1 lpm) 19.5 gpm (73.8 lpm)
Capacity (flow per revolution) 0.035 gal/rev (0.132 l/rev) 0.048 gal/rev (0.182 l/rev) 0.11 gal/rev (0.416 l/rev) 0.15 gal/rev (0.568 l/rev)
Maximum discharge pressure 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar)
Hose inner diameter 16 mm 19 mm 25 mm 29 mm
Port size 3/4 in male NPT 3/4 in male NPT 1-1/4 in male NPT 1-1/4 in male NPT

EP3016 Performance EP3019 Performance EP4025 Performance EP4029 Performance

4.5 7 14 20
4.0 18
6 12
3.5 16
5 10 14
3.0
2 Hp
2 Hp
FLOW (gpm)

FLOW (gpm)

FLOW (gpm)

FLOW (gpm)
MOTOR Hp

MOTOR Hp

MOTOR Hp

MOTOR Hp

8 12
1-1/2 Hp

1-1/2 Hp

2.5 4
10
2.0 3 6 8
1.5 6
2 4
1-1/2 Hp

1.0
1-1/2 Hp

4
0.5 1 2
2
0.0 0 0 0
0 20 40 60 80 100 120 0 20 40 60 80 100 120 0 20 40 60 80 100 120 0 20 40 60 80 100 120
PUMP SPEED (rpm) PUMP SPEED (rpm) PUMP SPEED (rpm) PUMP SPEED (rpm)

53
process equipment catalog
 EP Series Hose Pumps

Graco Assembled Complete Pumps

Step 2: Choose Your Pump Speed Range

Model EP2006 EP2010 EP2013

Max flow @ 130 rpm - gpm (lpm) 0.5 (2.0) 1.2 (4.4) 2.1 (7.9)
Flow/Rev - gal/rev (l/rev) 0.004 (0.015) 0.009 (0.034) 0.016 (0.060)
Pump Speed Range Low Mid High Low Mid High Low Mid High
Pump Speed @ 60 Hz - rpm 11 35 90 11 51 90 11 51 90
Flow Rate @ 60 Hz - gpm (lpm) 0.046 0.14 0.36 0.10 0.46 0.81 0.17 0.82 1.4
(0.17) (0.52) (1.36) (0.37) (1.74) (3.06) (0.64) (3.1) (5.2)
Maximum Working Pressure 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar)
Maximum Suction Lift - ft (m) 29 (8.9) 29 (8.9) 29 (8.9)
Pump Inlet / Outlet Size 1/2” male NPT 1/2” male NPT 1/2” male NPT
Operation Manual 3A1938 3A1938 3A1938
Repair Parts Manual 3A1940 3A1940 3A1940
Flyer 344964 344964 344964

Step 3: Choose Your Hose & Hose Barb Materials

Hose Barb
Hose Material Material EP2006 EP2010 EP2013
Natural Rubber 316 SST 24L104 24L118 24L132 24L146 24L160 24L174 24L188 24L202 24L216
Hastelloy-C
Nitrile 316 SST 24L107 24L121 24L135 24L149 24L163 24L177 24L191 24L205 24L219
Hastelloy-C 24L108 24L122 24L136 24L150 24L164 24L178 24L192 24L206 24L220
Nitrile Food Grade 316 SST 24L109 24L123 24L137 24L151 24L165 24L179 24L193 24L207 24L221
Hastelloy-C 24L110 24L124 24L138 24L152 24L166 24L180 24L194 24L208 24L222
EPDM 316 SST 24L100 24L114 24L128 24L142 24L156 24L170 24L184 24L198 24L212
Hastelloy-C 24L101 24L115 24L129 24L143 24L157 24L171 24L185 24L199 24L213
EPDM Food Grade 316 SST 24L102 24L116 24L130 24L144 24L158 24L172 24L186 24L200 24L214
Hastelloy-C 24L103 24L117 24L131 24L145 24L159 24L173 24L187 24L201 24L215
Neoprene 316 SST 24L111 24L125 24L139 24L153 24L167 24L181 24L195 24L209 24L223
Hastelloy-C
CSM 316 SST 24L105 24L119 24L133 24L147 24L161 24L175 24L189 24L203 24L217
Hastelloy-C 24L106 24L120 24L134 24L148 24L162 24L176 24L190 24L204 24L218
UHMW PE 316 SST 24L112 24L126 24L140 24L154 24L168 24L182 24L196 24L210 24L224
Hastelloy-C 24L113 24L127 24L141 24L155 24L169 24L183 24L197 24L211 24L225

54
process equipment catalog
 EP Series Hose Pumps

Graco Assembled Complete Pumps

EP3016 EP3019 EP4025 EP4029

4.6 (17.2) 6.2 (23.6) 14.3 (54.1) 19.5 (73.8)
0.035 (0.132) 0.048 (0.182) 0.11 (0.416) 0.15 (0.568)
Low Mid High Low Mid High Low Mid High Low Mid High
18 50 87 18 50 87 23 52 91 23 52 91
0.63 1.8 3.1 0.86 2.4 4.2 2.5 5.8 10.1 3.4 7.9 13.7
(2.4) (6.8) (11.7) (3.2) (9.0) (15.8) (9.4) (21.9) (38.2) (12.8) (29.9) (51.8)
200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar)
29 (8.9) 29 (8.9) 29 (8.9) 29 (8.9)
3/4” male NPT 3/4” male NPT 1-1/4” male NPT 1-1/4” male NPT
3A1938 3A1938 3A1938 3A1938
3A1939 3A1939 3A1939 3A1939
344964 344964 344964 344964

EP3016 EP3019 EP4025 EP4029

24L504 24L518 24L532 24L546 24L560 24L574 25L002 25L010 25L018 25L028 25L042 25L056

24L507 24L521 24L535 24L549 24L563 24L577 25L004 25L012 25L020 25L031 25L045 25L059
24L508 24L522 24L536 24L550 24L564 24L578 25L032 25L046 25L060
24L509 24L523 24L537 24L551 24L565 24L579 25L005 25L013 25L021 25L033 25L047 25L061
24L510 24L524 24L538 24L552 24L566 24L580 25L034 25L048 25L062
24L500 24L514 24L528 24L542 24L556 24L570 25L000 25L008 25L016 25L024 25L038 25L052
24L501 24L515 24L529 24L543 24L557 24L571 25L025 25L039 25L053
24L502 24L516 24L530 24L544 24L558 24L572 25L001 25L009 25L017 25L026 25L040 25L054
24L503 24L517 24L531 24L545 24L559 24L573 25L027 25L041 25L055
24L511 24L525 24L539 24L553 24L567 24L581 25L006 25L014 25L022 25L035 25L049 25L063

24L505 24L519 24L533 24L547 24L561 24L575 25L003 25L011 25L019 25L029 25L043 25L057
24L506 24L520 24L534 24L548 24L562 24L576 25L030 25L044 25L058
24L512 24L526 24L540 24L554 24L568 24L582 25L007 25L015 25L023 25L036 25L050 25L064
24L513 24L527 24L541 24L555 24L569 24L583 25L037 25L051 25L065

55
process equipment catalog
 EP Series Hose Pumps

Graco Pump Kits with roller not installed (fully assembled pumps with the roller shipped in a separate package)
Step 2: Choose Your Pump Speed Range

Model EP2006 EP2010 EP2013

Max flow @ 130 rpm - gpm (lpm) 0.5 (2.0) 1.2 (4.4) 2.1 (7.9)
Flow/Rev - gal/rev (l/rev) 0.004 (0.015) 0.009 (0.034) 0.016 (0.060)
Pump Speed Range Low Mid High Low Mid High Low Mid High
Pump Speed @ 60 Hz - rpm 11 35 90 11 51 90 11 51 90
Flow Rate @ 60 Hz - gpm (lpm) 0.046 0.14 0.36 0.10 0.46 0.81 0.17 0.82 1.4
(0.17) (0.52) (1.36) (0.37) (1.74) (3.06) (0.64) (3.1) (5.2)
Maximum Working Pressure 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar)
Maximum Suction Lift - ft (m) 29 (8.9) 29 (8.9) 29 (8.9)
Pump Inlet / Outlet Size 1/2” male NPT 1/2” male NPT 1/2” male NPT
Operation Manual 3A1938 3A1938 3A1938
Repair Parts Manual 3A1940 3A1940 3A1940
Flyer 344964 344964 344964

Step 3: Choose Your Hose & Hose Barb Materials

Hose Barb
Hose Material Material EP2006 EP2010 EP2013
Natural Rubber 316 SST 24L374 24L388 24L402 24L416 24L430 24L444 24L458 24L472 24L486
Hastelloy-C
Nitrile 316 SST 24L377 24L391 24L405 24L419 24L433 24L447 24L461 24L475 24L489
Hastelloy-C 24L378 24L392 24L406 24L420 24L434 24L448 24L462 24L476 24L490
Nitrile Food Grade 316 SST 24L379 24L393 24L407 24L421 24L435 24L449 24L463 24L477 24L491
Hastelloy-C 24L380 24L394 24L408 24L422 24L436 24L450 24L464 24L478 24L492
EPDM 316 SST 24L370 24L384 24L398 24L412 24L426 24L440 24L454 24L468 24L482
Hastelloy-C 24L371 24L385 24L399 24L413 24L427 24L441 24L455 24L469 24L483
EPDM Food Grade 316 SST 24L372 24L386 24L400 24L414 24L428 24L442 24L456 24L470 24L484
Hastelloy-C 24L373 24L387 24L401 24L415 24L429 24L443 24L457 24L471 24L485
Neoprene 316 SST 24L381 24L395 24L409 24L423 24L437 24L451 24L465 24L479 24L493
Hastelloy-C
CSM 316 SST 24L375 24L389 24L403 24L417 24L431 24L445 24L459 24L473 24L487
Hastelloy-C 24L376 24L390 24L404 24L418 24L432 24L446 24L460 24L474 24L488
UHMW PE 316 SST 24L382 24L396 24L410 24L424 24L438 24L452 24L466 24L480 24L494
Hastelloy-C 24L383 24L397 24L411 24L425 24L439 24L453 24L467 24L481 24L495

56
process equipment catalog
 EP Series Hose Pumps

Graco Pump Kits with roller not installed

EP3016 EP3019 EP4025 EP4029

4.6 (17.2) 6.2 (23.6) 14.3 (54.1) 19.5 (73.8)
0.035 (0.132) 0.048 (0.182) 0.11 (0.416) 0.15 (0.568)
Low Mid High Low Mid High Low Mid High Low Mid High
18 50 87 18 50 87 23 52 91 23 52 91
0.63 1.8 3.1 0.86 2.4 4.2 2.5 5.8 10.1 3.4 7.9 13.7
(2.4) (6.8) (11.7) (3.2) (9.0) (15.8) (9.4) (21.9) (38.2) (12.8) (29.9) (51.8)
200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar) 200 psi (13.8 bar)
29 (8.9) 29 (8.9) 29 (8.9) 29 (8.9)
3/4” male NPT 3/4” male NPT 1-1/4” male NPT 1-1/4” male NPT
3A1938 3A1938 3A1938 3A1938
3A1939 3A1939 3A1939 3A1939
344964 344964 344964 344964

EP3016 EP3019 EP4025 EP4029

24L588 24L602 24L616 24L630 24L644 24L658 25L068 25L076 25L084 25L094 25L108 25L122

24L591 24L605 24L619 24L633 24L647 24L661 25L070 25L078 25L086 25L097 25L111 25L125
24L592 24L606 24L620 24L634 24L648 24L662 25L098 25L112 25L126
24L593 24L607 24L621 24L635 24L649 24L663 25L071 25L079 25L087 25L099 25L113 25L127
24L594 24L608 24L622 24L636 24L650 24L664 25L100 25L114 25L128
24L584 24L598 24L612 24L626 24L640 24L654 25L066 25L074 25L082 25L090 25L104 25L118
24L585 24L599 24L613 24L627 24L641 24L655 25L091 25L105 25L119
24L586 24L600 24L614 24L628 24L642 24L656 25L067 25L075 25L083 25L092 25L106 25L120
24L587 24L601 24L615 24L629 24L643 24L657 25L093 25L107 25L121
24L595 24L609 24L623 24L637 24L651 24L665 25L072 25L080 25L088 25L101 25L115 25L129

24L589 24L603 24L617 24L631 24L645 24L659 25L069 25L077 25L085 25L095 25L109 25L123
24L590 24L604 24L618 24L632 24L646 24L660 25L096 25L110 25L124
24L596 24L610 24L624 24L638 24L652 24L666 25L073 25L081 25L089 25L102 25L116 25L130
24L597 24L611 24L625 24L639 24L653 24L667 25L103 25L117 25L131

57
process equipment catalog
 EP Series Hose Pumps

Ordering & Mounting Information

Hose Pumps with No Motor Drive (fully assembled pumps with customer supplied motor drive)
Hose Barb
Hose Material Material EP2006 EP2010 EP2013 EP3016 EP3019 EP4025 EP4029
Natural Rubber 316 SST 24M739 24M753 24M767 24M781 24M795 24M810 24M820
Hastelloy-C
Nitrile 316 SST 24M742 24M756 24M770 24M784 24M798 24M812 24M823
Hastelloy-C 24M743 24M757 24M771 24M785 24M799 24M824
Nitrile Food Grade 316 SST 24M744 24M758 24M772 24M786 24M800 24M813 24M825
Hastelloy-C 24M745 24M759 24M773 24M787 24M801 24M826
EPDM 316 SST 24M735 24M749 24M763 24M777 24M791 24M808 24M816
Hastelloy-C 24M736 24M750 24M764 24M778 24M792 24M817
EPDM Food Grade 316 SST 24M737 24M751 24M765 24M779 24M793 24M809 24M818
Hastelloy-C 24M738 24M752 24M766 24M780 24M794 24M819
Neoprene 316 SST 24M746 24M760 24M774 24M788 24M802 24M814 24M827
Hastelloy-C
CSM 316 SST 24M740 24M754 24M768 24M782 24M796 24M811 24M821
Hastelloy-C 24M741 24M755 24M769 24M783 24M797 24M822
UHMW PE 316 SST 24M747 24M761 24M775 24M789 24M803 24M815 24M828
Hastelloy-C 24M748 24M762 24M776 24M790 24M804 24M829

Mounting a Non-Graco Motor (to mount a non-graco motor and gearbox to a bare EP Hose Pump)
EP Series Hollow Bore Shaft Bolt Circle Flange Pilot Mounting Hole Thread
Pump Size Diameter A Diameter B Diameter C Size D
EP2 20 mm 100 mm 80 mm M6
EP3 30 mm 130 mm 110 mm M8
EP4 35 mm 165 mm 130 mm M10

D D

C
C
B
B

A A

Motor mounting dimensions for EP2 Pumps Motor mounting dimensions for EP3 & EP4 Pumps

58
process equipment catalog
 EP Series Hose Pumps

Kits and Replacement Hoses Ordering Information

Replacement Hose Kits*
EP2006 EP2010 EP2013 EP3016 EP3019 EP4025 EP4029
Natural Rubber 24K482 24K492 24K502 24K522 24K532 24K542 24K552
Nitrile 24K484 24K494 24K504 24K524 24K534 24K544 24K554
Nitrile Food Grade 24K486 24K496 24K506 24K526 24K536 24K546 24K556
EPDM 24K483 24K493 24K503 24K523 24K533 24K543 24K553
EPDM Food Grade 24K485 24K495 24K505 24K525 24K535 24K545 24K555
Neoprene 24K489 24K499 24K509 24K529 24K539 24K549 24K559
UHMW PE 24K488 24K498 24K508 24K528 24K538 24K548 24K558
CSM 24K487 24K497 24K507 24K527 24K537 24K547 24K557
*Includes 2 clamps

VFDs (Variable Frequency Drives)

Hp Input Voltage Output Voltage Used with Pump Part Number
0.5 120 or 240 VAC (1 Phase) 240 VAC (3 Phase) EP2006 16K905
0.5 208-240 VAC (1 or 3 Phase) 208-240 VAC (3 Phase) EP2006 16K906
1 120 or 240 VAC (1 Phase) 240 VAC (3 Phase) EP2010, EP2013 16K907
1 208-240 VAC (1 or 3 Phase) 208-240 VAC (3 Phase) EP2010, EP2013 16K908
1.5 120 or 240 VAC (1 Phase) 240 VAC (3 Phase) EP3016, EP3019 16K909
1.5 208-240 VAC (1 or 3 Phase) 208-240 VAC (3 Phase) EP3016, EP3019 16K910
2 208-240 VAC (1 or 3 Phase) 208-240 VAC (3 Phase) EP4025, EP4029 16K911
2 400-480 VAC (3 Phase) 400-480 VAC (3 Phase) EP4025, EP4029 16K912

Hose Pump Lubricant

Description Part Number
Glycerin Based Hose Lube (1 quart) 24K692
Glycerin Based Hose Lube (1 gallon) 24K694
Glycerin Based Hose Lube (55 gallon drum) 24M435
Silicone Based Hose Lube (1 gallon) 24K686
Silicone Based Hose Lube (55 gallon drum) 24M434
EP2 requires 8 oz (250 mL) of hose lube; EP3 requires 1 qt (1 l) of hose lube; EP4 requires 1/2 gallon (2 l) of hose lube
Factory fill is glycerin, shipped in a separate bottle

Other
Description Part Number
“Band-It” Clamp Tool 24L497

59
process equipment catalog
 EP Series Hose Pumps

Dimensions
Dimensions
EP2 Hose Pumps EP3 Hose Pumps

16.65 in
(423 mm)
17.20 in
(437 mm)

11.81 in (300 mm) 27.39 in (696 mm)

13.52 in (344 mm)

8.98 in (228 mm)

11.02 in (280 mm)

EP4 Hose Pumps

19.35 in
(492 mm)

15.91 in (404 mm) 34.15 in (868 mm)

16.86 in (428 mm)

13.35 in (339 mm)

60
process equipment catalog
 Hydra-Clean®
Air-Operated Pressure Washers

Ordering Information
Wall Mount Hydra-Clean Package
Package Order No. 247550 247552 247554 258665 Pump Package

Air Motor Part No. N34DN0 N65DN0 N65DN0 N65DNO

Pump Lower Part No. 247599 241648 687055 24B923
Pump Construction SST SST SST SST
Standard Seal Repair Kit 247881 222880 See manual 24C162
311825
Standard Seal Construction PTFE/ UHMWPE/ UHMWPE/ UHMWPE/
CF-PTFE CF-PTFE CF-PTFE CF-PTFE
Optional Seal Repair Kits 207581 222875 222845 237713
Optional Seal Construction PTFE UHMWPE/PTFE UHMWPE/PTFE UHMWPE/PTFE
Flyer 338026 338026 338026 338026
Instruction Manual 312585 312585 312585 312585

Cart Mount Hydra-Clean Package

Package Order No. 247549 247551 247553 258664 Pump Package

Air Motor Part No. N34DN0 N65DN0 N65DN0 N65DNO

Pump Lower Part No. 247599 241648 687055 24B923
Pump Construction SST SST SST SST
Standard Seal Repair Kit 247881 222880 See manual 24C162
311825
Standard Seal Construction PTFE/ UHMWPE/ UHMWPE/ UHMWPE/
CF-PTFE CF-PTFE CF-PTFE CF-PTFE
Optional Seal Repair Kits 207581 222875 222845 237713
Optional Seal Construction PTFE UHMWPE/PTFE UHMWPE/PTFE UHMWPE/PTFE
Flyer 338026 338026 338026 338026
Instruction Manual 312585 312585 312585 312585

Drum Mount Hydra-Clean Package

Package Order No. 206515 Pump Package

Air Motor Part No. 207352

Pump Lower Part No. 224344
Pump Construction SST
Standard Seal Repair Kit 224402
Standard Seal Construction UHMWPE/Polychloroprene
Optional Seal Construction UHMWPE/PTFE
Instruction Manual 306817

61
process equipment catalog
 Hydra-Clean Pressure Washers

Technical Specifications
Max. Working Max. Air Input Fluid Flow Vol. per Air Fluid Fluid
Part Pump
Pressure psi Pressure psi at 60 cpm Cycle Inlet Inlet Outlet Flyer Manual
Number Package
(bar, MPa) (bar, MPa) gpm (lpm) oz (cc) Size Size Size*
247549 12:1 Cart Mount 1250 (86, 8.6) 100 (7, 0.7) 8.7 (33.0) 18.6 (550) 3/4 npt(f) 1 in 3/8 in 338026 312585
247550 12:1 Wall Mount 1250 (86, 8.6) 100 (7, 0.7) 8.7 (33.0) 18.6 (550) 3/4 npt(f) 1 in 3/8 in 338026 312585
247551 23:1 Cart Mount 2275 (157, 15.7) 100 (7, 0.7) 9.2 (34.7) 19.6 (580) 3/4 npt(f) 1 in 3/8 in 338026 312585
247552 23:1 Wall Mount 2275 (157, 15.7) 100 (7, 0.7) 9.2 (34.7) 19.6 (580) 3/4 npt(f) 1 in 3/8 in 338026 312585
247553 30:1 Cart Mount 3065 (211, 21.1) 100 (7, 0.7) 6.8 (25.9) 14.5 (430) 3/4 npt(f) 1 in 3/8 in 338026 312585
247554 30:1 Wall Mount 3065 (211, 21.1) 100 (7, 0.7) 6.8 (25.9) 14.5 (430) 3/4 npt(f) 1 in 3/8 in 338026 312585
258664 45:1 Cart Mount 4500 (310, 31.0) 100 (7, 0.7) 4.6 (17.4) 9.8 (290) 3/4 npt(f) 1 in 3/8 in 338026 312585
258665 45:1 Wall Mount 4500 (310, 31.0) 100 (7, 0.7) 4.6 (17.4) 9.8 (290) 3/4 npt(f) 1 in 3/8 in 338026 312585
206515 10:1 Drum Mount 1800 (125, 12.5) 180 (12.5, 1.2) 3.0 (11.4) 6.4 (189) 1/2 npt(f) 1/2 in 3/4 in — 306817
*Includes two outlet ports per unit

Accessories
Guns and Wands Hoses
247879 Replacement gun/wand 214959 1 in x 6 ft inlet hose
15T283 Brass/stainless spray gun 247878 3/8 in x 50 ft outlet hose: 4500 psi
15T282 Stainless steel spray gun
Other
15T279 32 inch stainless steel wand
15T284 60 mesh inlet strainer with 1” NPT(f) connection
15T280 10 inch stainless steel wand
191635 10 mesh inlet strainer with 1” NPT(f) connection
247880 Gun stainless steel connections
247622 Gun and suction tube holder

Stainless Steel Tips

Part Orifice Size Fan Width Angle at Capacity at 1000 psi
Number in (mm) 40 psi (3 bar, 0.03 MPa) (68.9 bar, 6.89 MPa) GPM (lpm)
805534 0.020 (0.51) 40º 1.00 (3.78)
805538* 0.030 (0.76) 40º 1.50 (5.68)
805542 0.035 (0.89) 40º 1.75 (6.62)
805549* 0.045 (1.14) 25º 2.25 (8.52)
805561 0.060 (1.52) 25º 3.00 (11.36)
805566* 0.065 (1.65) 40º 3.25 (12.30)
805569 0.070 (1.78) 25º 3.50 (13.25)
805574 0.075 (1.91) 40º 3.75 (14.20)
805575* 0.080 (2.03) 0º 4.00 (15.14)
805584 0.090 (2.28) 15º 4.50 (17.03)
805587 0.100 (2.54) 0º 5.00 (18.93)
Other orifice sizes and fan widths available from Graco, contact a sales representative for more information.

62
process equipment catalog
 Hydra-Clean Pressure Washers

Dimensions
Wall Mount Package 247550 Cart Mount Package 247549

17.1 in
(451 mm)

50.0 in
44.3 in (1270 mm)
(1125 mm)

30.8 in
(782 mm)

17.1 in
(434 mm)

17.1 in
(434 mm)

5.6 in
(142 mm)

25.7 in
Refer to manual 312585 for additional package dimensions (653 mm)

63
process equipment catalog
 CycleFlo™ and CycleFlo II
Title
Subhead Pump Controllers
Solenoid

Ordering Information
195264 CycleFlo Pneumatic pump controller, 120V
196706 CycleFlo Pneumatic pump controller, 240V
195265 CycleFlo II Pneumatic pump controller, 120V
309003 CycleFlo Instruction Manual
309004 CycleFlo II Instruction Manual

Product Selector
Highlighted areas indicate the different sizes of remote pumps and available materials of construction for seats, balls and diaphragms
that can be used with the CycleFlo and CycleFlo II controller.

Pump Size (air motor type and material) Wetted Parts Seats Balls Diaphragm

2 = 1/4” (6.35 mm) Remote: polypropylene center section 1 = Acetal (npt) 0 = Seat with ball 1 = PTFE 1 = PTFE
4 = 1/2” (12.7 mm) Remote: polypropylene center section 2 = Poly (npt) 2 = Acetal 2 = Acetal 5 = TPE
4 = 3/4” (19.05 mm) Remote: polypropylene center section 3 = Aluminum (npt) 3 = Stainless Steel 3 = Stainless Steel 6 = Santoprene
C = 1-1/2” (38.1 mm) Remote: aluminum center section 4 = Stainless Steel (npt) 4 = Hardened SST 4 = Hardened SST 7 = Buna N
U = 1-1/2” (38.1 mm) Remote: stainless steel center section 5 = PVDF (npt) 5 = TPE 5 = TPE 8 = Fluoroelastomer
G = 2” (50.8 mm) Remote: aluminum center section 6 = Ductile Iron (npt) 6 = Santoprene 6 = Santoprene G = Geolast
7 = Buna N 7 = Buna N
A = Acetal * (bsp) 8 = Fluoroelastomer 8 = Fluoroelastomer
B = Poly * (bsp) 9 = Polypropylene 9 = Polypropylene
C = Aluminum (bsp) A = PVDF A = PVDF
D = Stainless Steel (bsp) G = Geolast G = Geolast
E = PVDF (bsp)
F = Ductile Iron (bsp) B = SST with viton seal
C = Santoprene with
H = 2 npt Alum Extended viton seal
G = 2 bsp Alum Extended D = Urethane Duckbill

Mounting Dimensions

CycleFlo CycleFlo II
4 in
(102 mm)

7.375 in (187 mm)

5 in
7.375 in
8.875 in (127 mm)
(187 mm)
(225 mm)

5 in (127 mm)

64
process equipment catalog
 CycleFlo and CycleFlo II

How To Determine The Best Remote Pump:

1. C
 onfigure the best seat, ball and diaphragm combination, as well as fluid wetted parts, based on material compatibility and
application requirements.
• If the material is a mild acid, the choice could be a DX2911.
2. D
 etermine dispense time and volume accuracy.
• In two minutes, 50 gallons need to be dispensed ±5% accuracy
3. U
 se the displacement volume chart below to choose the pump size with an outlet volume/cycle that is most closely
divisible into your required flow.*
• Husky 1590 produces .5 gal/cycle
• Husky 2150 produces 1.03 gal/cycle

Husky 205 Husky 515 Husky 716 Husky 1050 Husky 1590 Husky 2150
Volume/cycle 1/4 in 1/2 in 3/4 in 1 in 1-1/2 in 2 in
Cubic centimeters (cc) 46 150 150 644 1960 3000
Liters 0.05 0.15 0.15 0.64 1.96 3.9
Grams (assumes s.g =1.0) 46 150 150 644 1960 3900
Kilograms (kg) 0.05 0.15 0.15 0.64 1.96 3.9
Gallons 0.01 0.04 0.04 0.17 0.50 1.03
Quarts 0.05 0.16 0.16 0.68 2.0 4.12
Pints 0.1 0.32 0.32 1.36 4.0 8.24
Ounces 1.54 5.12 5.12 21.8 64.0 131.84
Cubic inch 2.77 9.24 9.24 39.27 115.5 237.93

4. D
 etermine the number of cycles required. Calculate the dispense time by dividing required flow by outlet volume per cycle.
• Husky 1590 = 50 gal/0.5 gal/cycle = 100 cycles
• Husky 2150 = 50 gal/1.03 gal/cycle = 48.55 cycles
5. D
 etermine if cycle output is within the dispense accuracy required.
• Husky 2150 requires 48.55 cycles to pump 50 gallons. Only full cycles are possible, so either 48 or 49 cycles can be counted. At the 48 cycle
count, dispense would be 49.44 gallons. At the 49 cycle count, dispense would be 50.47 gallons.
• Husky 1590 requires 100 cycles to pump 50 gallons. No partial cycles required.
6. A fter determining the best size, use the pump ordering matrix to decide which remote center section is most suitable for the
application ­– DC2911 (aluminum center section) or DU5911 (stainless steel center section).
• Since a mild acid is being pumped, DC2911, an aluminum center section would be the best choice.

CycleFlo CycleFlo II

* Displacement values are estimates based on average running conditions.

65
process equipment catalog
 Fast-Flo® 1:1
Air-Operated Piston Transfer Pumps

Ordering Information Technical Specifications

Fast-Flo 1:1 Priming Piston
part number construction packing
Maximum fluid working pressure 180 psi (12.4 bar, 1.24 MPa)
Maximum pump speed 100 cpm
226940 Drum/CS/SST (ETL-UL, CE) T&L
Pump cycles per gallon (3.8 l) 25
226941 Drum/CS/SST (ETL-UL, CE) PE Maximum air input pressure 180 psi (12.4 bar, 1.24 MPa)
226942 Drum/SST (ETL-UL, CE) PE Maximum operating temperature 120°F (49°C)
Typical sound level 72 dBa
226943 Stubby/CS/SST (ETL-UL, CE) L Air inlet 1/4 npt (f)
226944 Stubby/CS/SST (ETL-UL, CE) PE Fluid outlet 3/4 npt (f)
Weight 20 lbs (9.07 kg) Drum;
Popular Models 226945 Stubby/SST (ETL-UL, CE) PE 11 lbs (4.99 kg) Stubby
226946 Drum/CS/SST (CE) T Instruction Manual 307427
237129 Drum/SST (CE) T
237130 Stubby/CS (CE) L
237131 Stubby/CS (CE) T
237132 Stubby/SST (CE) T
237133 Drum/CS (CE) L
237134 Drum/CS (CE) T
N = Neoprene SST = 304 Stainless Steel
L = Leather CS = Carbon Steel
T = PTFE PE = Polyethylene

Performance Charts Dimensions

Fast-Flo 1:1 Performance

120 300
(8.4, 0.84) (8.4)
A
FluID outlet PreSSure psi (bar, MPa)

100 250
aIr conSumPtIon scfm (m3/min)

(7, 0.7) (7.0) 51.7 in.

80 200 (1315 mm)
B
(5.5, 0.55) (5.6)
60 A 150
(4.1, 0.41) (4.2)
40 C B 100
(2.8, 0.28) (2.8)
C
20 50
(1.4, 0.14) (1.4)
45.6 in.
0
gpm 0 1 2 3 4 5 6 7 8 (1158 mm)
(lpm) (3.8) (7.6) (11) (15.2) (18.9) (22.8) (26.5) (30.4) Extends to 63.5 in.
FluiD FlOW (1614 mm)

34.6 in.
aIr PreSSure legenD
(880 mm)
A = at 100 psi (7 bar, 0.7 MPa) Air Consumption
B = at 70 psi (4.8 bar, 0.48 MPa) Fluid Flow
C = at 40 psi (2.8 bar, 0.28 MPa)

28.5 in.
(724 mm)

Extends to 46.4 in.

(1180 mm)

66
process equipment catalog
 Piston Pumps for Ink Applications
Ink Applications

Ordering Information and Technical Specifications

Piston Pumps with Sealed Wet Cup
Maximum Air or
Ink Pump Hydraulic Input Maximum Fluid
Package Remote Power Displacement Pressure Working Pressure
Part No. Series Ratio DataTrak DataTrak Source Pump Size psi (MPa, bar) psi (MPa, bar)
258744 A 14:1 Air 500 cc 100 (0.7, 7.0) 1400 (9.7, 97)
258745 A 14:1 x Air 500 cc 100 (0.7, 7.0) 1400 (9.7, 97)
258746 A 14:1 x Air 500 cc 100 (0.7, 7.0) 1400 (9.7, 97)
258747 A 23:1 Air 200 cc 100 (0.7, 7.0) 2300 (15.9, 159)
258748 A 23:1 x Air 200 cc 100 (0.7, 7.0) 2300 (15.9, 159)
258749 A 23:1 x Air 200 cc 100 (0.7, 7.0) 2300 (15.9, 159)
258750 A 26:1 Air 500 cc 100 (0.7, 7.0) 2600 (17.9, 179)
258751 A 26:1 x Air 500 cc 100 (0.7, 7.0) 2600 (17.9, 179)
258752 A 26:1 x Air 500 cc 100 (0.7, 7.0) 2600 (17.9, 179)
258753 A 1.6:1 Hydraulic Oil 500 cc 1500 (10, 103) 2300 (15.9, 159)

Motor Conversion Kits

Part No. Description
24C743 To install an L200CM Check-Mate displacement pump on an existing King air motor
24C744 To install an L500CM Check-Mate displacement pump on an existing King air motor
24D625 To install an L500CM Check-Mate displacement pump on an existing Viscount II hydraulic motor

Piston Pumps with Sealed Wet Cup

Stroke length
Pneumatic 4.75 in (120.65 mm)
Hydraulic 4.69 in (119.13 mm)
Maximum fluid operating temperature 180° F (82.3° C)
Air or Hydraulic Inlet Size 3/4 npt (f)
Fluid outlet size 200 cc displacement pump: 1 npt (f)
500 cc displacement pump: 1-1/2 npt (f)
Maximum pump speed 60 cpm
(Do not exceed maximum recommended speed of fluid pump, to prevent premature pump wear)

Other
Part No. Description
222780 Floor Stand Kit
See manual 307971

Pneumatic Hydraulic

67
process equipment catalog
 Piston Pumps for Ink Applications
Ink Applications

Ordering Information and Technical Specifications

Name of Pump Senator® 19:1 Viscount® II 1900 Bulldog® 31:1 Viscount II 3100
Lower size 800 800 800 800
Maximum fluid pressure 1900 psi (131 bar, 13.1 MPa) 1900 psi (131 bar, 13.1 MPa) 3100 psi (213 bar, 21.3 MPa) 3100 psi (213 bar, 21.3 MPa)
Maximum motor inlet pressure 100 psi (air) (6.9 bar, 0.69 MPa) 450 psi (oil) (31 bar, 3.1 MPa) 100 psi (air) (6.9 bar, 0.69 Mpa) 750 psi (oil) (51.7 bar, 5.1 MPa)
Flow rate @ 60 cpm 2.8 gpm (10.6 lpm) 2.8 gpm (10.6 lpm) 2.8 gpm (10.6 lpm) 2.8 gpm (10.6 lpm)
Cfm or gpm required per gallon 24 cfm 4.3 gpm (16.2 lpm) 32 cfm 4.3 gpm (16.2 lpm)
Fluid pump outlet size 1” npt (f) 1” npt (f) 1” npt (f) 1” npt (f)
Motor inlet size 3/4” npt (f) 3/4” npt (f) 3/4” npt (f) 3/4” npt (f)
Weight of pump 160 lb (73 kg) 177 lb (80 kg) 160 lb (73 kg) 177 lb (80 kg)
Instruction manual 308351 308351 308351 308351

Bin Supply Senator 19:1 Viscount II 1900 Bulldog 31:1 Viscount II 3100
Pump 246941 246938 246940 246938
Air controls: FRL, 1/2” 217072 217072
Air run away control, 3/4” 224040 224040
Air speed control, 1/2”(f) 510441 510441
Floor stand (3” inlet) 222780 222780 222780 222780
Hydraulic controls* 236865 236865
Outlet hydraulic hose
connector 1”(m) x 1-1/2”(f), Not included Not included
1500 psi rated

Misc. Information Senator 19:1 Viscount II 1900 Bulldog 31:1 Viscount II 3100
Pump lower section 246939 246939 246939 246939
Ram plate replacement seals 165601 165601 165601 165601

*Hydraulic controls include hydraulic flow and pressure control, ball valves, 3 ft supply and return hose

19:1 Senator 31:1 Bulldog

68
process equipment catalog
 Piston Pumps for Ink Applications

Name of Pump Bulldog 12:1 Viscount II 1200 King® 24:1 Viscount II 2400
Lower size 2100 2100 2100 2100
Maximum fluid pressure 1200 psi (82.8 bar, 8.28 MPa) 1200 psi (82.8 bar, 8.28 MPa) 2400 psi (165 bar, 16.5 MPa) 2400 psi (165 bar, 16.5 MPa)
Maximum motor inlet pressure 100 psi (air) (6.9 bar, 0.69 MPa) 750 psi (oil) (51.7 bar, 5.1 Mpa) 100 psi (air) (6.9 bar, 0.69 Mpa) 1500 psi (oil) (103 bar, 10.3 Mpa)
Flow rate @ 60 cpm 7.5 gpm (28.4 lpm) 7.5 gpm (28.4 lpm) 7.5 gpm (28.4 lpm) 7.5 gpm (28.4 lpm)
Cfm or gpm required per gallon 20 cfm 1.6 gpm (6 lpm) 25 cfm 1.6 gpm (6 lpm)
Fluid pump outlet size 1-1/2” npt (m) 1-1/2” npt (m) 1-1/2” npt (m) 1-1/2” npt (m)
Motor inlet size 3/4” npt (f) 3/4” npt (f) 3/4” npt (f) 3/4” npt (f)
Weight of pump 142 lb (65 kg) 196 lb (89 kg) 160 lb (73 kg) 196 lb (89 kg)
Instruction manual 308149 308149 308149 308149

Bin Supply Bulldog 12:1 Viscount II 1200 King 24:1 Viscount II 2400
Pump 246935 246937 246936 246937
Air controls: FRL, 1/2” 217072 217072
Air run away control, 3/4” 224040 224040
Air speed control, 1/2”(f) 510441 510441
Floor stand (3” inlet) 222780 222780 222780 222780
Hydraulic controls* 236865 236865
Outlet hydraulic hose
connector 1”(m) x 1-1/2” (f), Not included Not included
1500 psi rated

Misc. Information Bulldog 12:1 Viscount II 1200 King 24:1 Viscount II 2400
Pump lower section 246934 246934 246934 246934
Ram plate replacement seals 165601 165601 165601 165601

*Hydraulic controls include hydraulic flow and pressure control, ball valves, 3 ft supply and return hose

12:1 Bulldog Viscount II 2100 24:1 King

69
process equipment catalog
 Piston Pumps for Ink Applications

Ordering Information and Technical Specifications

Piston Pumps President® 20:1

Lower size 450
Maximum fluid pressure 2000 psi (140 bar. 14 MPa)
Maximum motor inlet pressure 100 psi ( 7 bar, 0.7 MPa)
Flow rate @ 60 cpm 1.2 gpm (4.5 lpm)
Cfm or gpm required per gallon 35 cfm
Fluid pump outlet size 3/4” npt (f)
Motor inlet size 1/2” npt (f)
Weight of pump 50 lb (22.7 kg)
Instruction manual 308017

Bin Supply President 20:1

Pump 246933
Air controls: FRL, 3/8”(f) 110150
Floor stand (3” inlet) 222780
Air run away control, 3/4”(f) 224040
Air speed control 1/2”(f) 510441

Misc. Information President 20:1

Pump lower section 246932
Ram plate replacement seals 165601

20:1 President

70
process equipment catalog
 Surge Suppressors
Husky 750 and Husky 2000

Ordering Information
Husky 750, 3/4 in npt(f) Surge Suppressors
Polypropylene Stainless Steel Acetal
Automatic wetted bottom housing and wetted bottom housing and wetted bottom housing and
non-wetted top housing non-wetted top housing non-wetted top housing
Weight 9 lb (4.1 kg) 16 lb (7.3 kg) 9 lb (4.1 kg)
Suppressor with Buna-N bladder 239096 239095 239094
Suppressor with PTFE bellows 239121 239123 239125
Suppressor with Fluoroelastomer bladder 239122 239124 n/a
Polypropylene Stainless Steel Acetal
Adjustable wetted bottom housing and wetted bottom housing and wetted bottom housing and
non-wetted top housing non-wetted top housing non-wetted top housing
Weight 9 lb (4.1 kg) 16 lb (7.3 kg) 9 lb (4.1 kg)
Suppressor with Buna-N bladder 239091 239090 239089
Suppressor with PTFE bellows 239129 239131 239133
Suppressor with Fluoroelastomer bladder 239130 239132 n/a

Husky 2000, 2 in npt(f) Surge Suppressors

Polypropylene Stainless Steel

Automatic wetted bottom housing and wetted bottom housing,
non-wetted top housing polypropylene non-wetted top housing
Weight 18 lb (8.2 kg) 36 lb (16.3 kg)
Suppressor with Buna-N bladder 239092 239093
Suppressor with PTFE bellows 239128 239126
Suppressor with Fluoroelastomer bladder n/a 239127
Polypropylene Stainless Steel
Adjustable wetted bottom housing and wetted bottom housing,
non-wetted top housing polypropylene non-wetted top housing
Weight 18 lb (8.2 kg) 36 lb (16.3 kg)
Suppressor with Buna-N bladder 239087 239088
Suppressor with PTFE bellows 239136 239134
Suppressor with Fluoroelastomer bladder n/a 239135

239095
Automatic
239096
Automatic
239091
Adjustable

239126
Automatic
239088
Adjustable

Technical Specifications

Surge Suppressors Husky 750 Husky 2000

Max. air input pressure 120 psi (0.84 MPa, 8.4 bar) 120 psi (0.84 MPa, 8.4 bar)
Air line connection 1/4 npt 1/4 npt
Fluid inlet size 3/4 in npt(f) 2 in npt(f)
Instruction manual 308703 308703

71
process equipment catalog
 Notes

72
process equipment catalog
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special,
extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the
equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance
with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco
component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures,
accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance or structures,
accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the
claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to
the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be
made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN
CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but
not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will
provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the
furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence
of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de
ou en rapport, directement ou indirectement, avec les procedures concernées.

Equipment Misuse Hazard

General Misuse: Any misuse of Graco equipment or accessories, such as over-pressurizing, modifying parts, using incompatible chemicals and
fluids, or using worn or damaged parts, can cause them to rupture. Misuse of equipment can result in fluid injection, splashing in the eyes or on
the skin, or other serious bodily injury, or fire, explosion or property damage. NEVER alter or modify any part of Graco equipment; doing so could
cause the product to malfunction. CHECK all equipment regularly and repair or replace worn or damaged parts immediately. Always wear
protective eye wear, gloves, clothing and respirator as recommended by fluid and solvent manufacturers.
System Pressure: Be sure that all equipment and accessories used are rated to withstand the applicable MAXIMUM WORKING PRESSURE.
DO NOT exceed the maximum working pressure of any component or accessory used in a system.
Fluid and Solvent Compatibility: All chemicals used in a Graco sprayer must be compatible with wetted parts. Consult your chemical supplier to
ensure compatibility. Do not use 1:1:1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such
solvents in this equipment, which contains aluminum and/or zinc parts. Such use could result in a serious chemical reaction, with the possibility
of explosion, which could cause death, serious bodily injury and/or substantial property damage.
 ABOUT GRACO
Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products
move, measure, control, dispense and apply a wide range of fluids and viscous materials used
in vehicle lubrication, commercial and industrial settings.

The company’s success is based on its unwavering commitment to technical excellence, world-class
manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco
offers systems, products and technology that set the quality standard in a wide range of fluid handling
solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication,
and dispensing sealants and adhesives, along with power application equipment for the contractor
industry. Graco’s ongoing investment in fluid management and control will continue to provide
innovative solutions to a diverse global market.

GRACO LOCATIONS MAILING ADDRESS ASIA PACIFIC INDIA

P.O. Box 1441 Graco Hong Kong Ltd.
Minneapolis, MN 55440-1441 AUSTRALIA India Liaison Office
Tel: 612-623-6000 Graco Australia Pty Ltd. Room 443, Augusta Point
Fax: 612-623-6777 Suite 17, 2 Enterprise Drive Regus Business Centre 53
Bundoora, Victoria 3083 Golf Course Road
Australia Gurgaon, Haryana
Tel: 61 3 9468 8500 India 122001
AMERICAS Fax: 61 3 9468 8599 Tel: 91 124 435 4208
Fax: 91 124 435 4001
MINNESOTA
Worldwide Headquarters
Graco Inc. CHINA JAPAN
88 -11th Avenue N.E. Graco Hong Kong Ltd. Graco K.K.
Minneapolis, MN 55413 Shanghai Representative Office 1-27-12 Hayabuchi
Building 7 Tsuzuki-ku
1029 Zhongshan Road South Yokohama City, Japan 2240025
Huangpu District Tel: 81 45 593 7300
EUROPE Shanghai 200011 Fax: 81 45 593 7301
BELGIUM The People’s Republic of China
European Headquarters Tel: 86 21 649 50088 KOREA
Graco N.V. Fax: 86 21 649 50077 Graco Korea Inc.
Industrieterrein-Oude Bunders Shinhan Bank Building
Slakweidestraat 31 4th Floor #1599
3630 Maasmechelen, Gwanyang-Dong, Dongan-Ku,
Belgium Anyang-si, Korea 431-060
Tel: 32 89 770 700 Tel: 82 31 476 9400
Fax: 32 89 770 777 Fax: 82 31 476 9801

SALES/ Call today for product information or to request a demonstration.

DISTRIBUTION/
SERVICE
877-84GRACO (1-877-844-7226) or visit us at www.graco.com.
Graco Inc. is registered to I.S. EN ISO 9001

North America
Customer Service
800-328-0211
Fax 877-340-6427
©2001-2012 Graco Inc. 300435 Rev. M 07/11­All written and visual data contained in this document are based on the latest product information available at the
time of publication. Graco reserves the right to make changes at any time without notice. All other brand names or marks are used for identification purposes
and are trademarks of their respective owners.