DEPARTMENT OF THE AIR FORCE CFETP 2A6X1A/C/D/E

Headquarters US Air Force Parts I and II

Washington, DC 20330-1030 1 AUGUST 2002

AFSC 2A6X1A/C/D/E

AEROSPACE PROPULSION
JET ENGINE

CAREER FIELD EDUCATION

AND TRAINING PLAN
 CFETP 2A6X1A/C/D/E, August 2002

CAREER FIELD EDUCATION AND TRAINING PLAN

AEROSPACE PROPULSION JET ENGINE SPECIALTY
AFSC 2A6X1A/C/D/E

Table of Contents

PART I
Preface......................................................................................................................................... 2
Abbreviations/Terms Explained.................................................................................................. 3

Section A--General Information.................................................................................................. 5

Purpose of the CFETP
Use of the CFETP
Coordination and Approval of the CFETP

Section B--Career Progression and Information ......................................................................... 6

Specialty Description
Skill/Career Progression
Apprentice Level (3)
Journeyman Level (5)
Craftsman Level (7)
Superintendent Level (9)
Training Decisions
Community College of the Air Force
Career Field Path
Base/Unit Education and Training Manager Checklist

Section C--Skill Level Training Requirements ........................................................................... 12

Purpose
Training Requirements
Apprentice Level (3)
Journeyman Level (5)
Craftsman Level (7)
Superintendent Level (9)
Section D--Resource Constraints ................................................................................................ 14
Section E--Transitional Training Guide ...................................................................................... 14

PART II
Section A--Specialty Training Standard...................................................................................... 15
Section B--Course Objective List................................................................................................ 145
Section C--Support Materials...................................................................................................... 146
Section D--Training Course Index .............................................................................................. 150
Section E--MAJCOM Unique Requirements.............................................................................. 152
________________________
Supersedes: CFETP 2A6X1A/C/D/E, Feb 97 Approved By: HQ USAF/ILMM, CMS Matthew.McMahan
Change 1, Jul 97 OPR: 361 TRS/TRR (Daniel T. Chilenski)
Change 2, Apr 98 Number of printed pages: 150
Change 3, Feb 99
1
 CFETP 2A6X1A/C/D/E, August 2002

CAREER FIELD EDUCATION AND TRAINING PLAN

AEROSPACE PROPULSION JET ENGINE SPECIALTY
AFSC 2A6X1A/C/D/E

PART I

Preface

1. This Career Field Education and Training Plan (CFETP) is a comprehensive education and
training document that identifies life-cycle education/training requirements, training support
resources, and minimum core task requirements for this specialty. The CFETP will provide
personnel a clear career path to success and instill rigor in all aspects of career field training. To
read, review, or print a copy of the current CFETP, go to the Aircraft Maintenance Homepage at:
http://www.il.hq.af.mil/ilm/ilmm/acmaint/index.html. NOTE: Civilians occupying associated
positions will use Part II to support duty position qualification training.

2. The CFETP consists of two parts; both parts of the plan are used by supervisors to plan,
manage, and control training within the career field.

2.1. Part I provides information necessary for overall management of the specialty. Section A
explains how everyone will use the plan. Section B identifies career field progression
information, duties and responsibilities, training strategies, and career field path. Section C
associates each level with specialty qualifications (knowledge, education, training, and other).
Section D indicates resource constraints. Some examples are funds, manpower, equipment, and
facilities. Section E identifies transition training guide requirements to support career field
restructures.

2.2. Part II includes the following: Section A identifies the Specialty Training Standard (STS)
and includes duties, tasks, and technical references to support training; Air Education and
Training Command (AETC) conducted training; wartime course requirements; core tasks; and
correspondence course requirements. Section B contains the course objective list and training
standards supervisors use to determine if airmen satisfied training requirements. Section C
identifies available support materials. An example is a Qualification Training Package (QTP)
developed to support proficiency training. These QTP packages are identified in AFIND8,
Numerical Index of Specialized Education/Training Publications. Section D identifies a training
course index supervisors use to determine resources available to support training; included here
are both mandatory and optional courses. Section E identifies MAJCOM unique training
requirements supervisors use to determine additional training requirements unique to the
MAJCOM.

3. Using guidance provided in the CFETP will ensure individuals in this specialty receive
effective and efficient training at the appropriate point in their career. This plan will enable us to
train today’s work force for tomorrow’s jobs. At unit level, supervisors and trainers will use Part
II to identify, plan, and conduct training commensurate with the overall goals of this plan.

2
 CFETP 2A6X1A/C/D/E, August 2002

ABBREVIATIONS/TERMS EXPLAINED

Advanced Training (AT). Formal course which provides individuals who are qualified in one
or more positions of their Air Force Specialty (AFS) with additional skills/knowledge to enhance
their expertise in the career field. Training is for selected career airmen at the advanced level of
the AFS.

Air Force Job Qualification Standard (AFJQS). A comprehensive task list which describes a
particular job type or duty position. They are used by supervisors to document task qualifications.
The tasks on an AFJQS are common to all persons serving in the described duty position.

Career Field Education and Training Plan (CFETP). A CFETP is a comprehensive,

multipurpose document covering the entire spectrum of education and training for a career field.
It outlines a logical growth plan that includes training resources and is designed to make career
field training identifiable, to eliminate duplication, and to ensure training is budget defensible.

Certification. A formal indication of an individual’s ability to perform a task to required

standards.

Certification Official. A person the commander assigns to determine an individual’s ability to

perform a task to required standards.

Continuation Training. Additional training exceeding requirements with emphasis on present

or future duty assignments.

Core Task. A task Air Force Career Field Managers (AFCFMs) identify as a minimum
qualification requirement within an Air Force specialty regardless of duty position. Core tasks
identified with an */R are optional for AFRC and ANG.

Course Objective List (COL). A publication identifying the tasks and knowledge requirements
and respective standards provided to achieve a 3-/7-skill level in this career field. Supervisors
use the COL to assist in conducting graduate evaluations in accordance with AFI 36-2201,
Developing, Managing and Conducting Training.

Enlisted Specialty Training (EST). A mix of formal training (technical school) and informal
training (on-the-job) to qualify and upgrade airmen in each skill level of a specialty.

Exportable Training. Additional training via computer assisted, paper text, interactive video,
or other necessary means to supplement training.

Field Technical Training (Type 4). Special or regular on-site training conducted by a Training
Detachment (TD) or by a mobile training team (MTT).

Initial Skills Training. A formal resident course which results in award of a 3-skill level AFSC.

3
 CFETP 2A6X1A/C/D/E, August 2002

Instructional System Development (ISD). A deliberate and orderly process for developing,
validating, and reviewing instructional programs that ensures personnel are taught the knowledge
and skills essential for successful job performance.

Mission Ready Airman. A formal course which results in an airman receiving hands-on
training and task certification of selected tasks so the individual will be immediately productive
upon arrival at their first duty section.

Occupational Survey Report (OSR). A detailed report showing the results of an occupational
survey of tasks performed within a particular AFS.

On-the-Job Training (OJT). Hands-on, over-the-shoulder training at the duty location used to
certify personnel for both skill level upgrade and duty position qualification.

Qualification Training (QT). Actual hands-on task performance training designed to qualify an
airman in a specific duty position. This training occurs both during and after the upgrade training
process. It is designed to provide the performance skill/knowledge training required to do the
job.

Qualification Training Package (QTP). An instructional package designed for use at the unit
to qualify, or aid qualification, in a duty position or program, or on a piece of equipment. It may
be printed, computer-based, or in other audiovisual media.

Resource Constraints. Resource deficiencies, such as money, facilities, time, manpower, and
equipment, that preclude desired training from being delivered.

Specialty Training Standard (STS). An Air Force publication that describes an Air Force
specialty in terms of tasks and knowledge an airman may be expected to perform or to know on
the job. It serves as a contract between Air Education and Training Command and the functional
user to show which of the overall training requirements for an Air Force Specialty are taught in
formal schools, career development courses, and exportable courses.

Upgrade Training (UGT). A mixture of mandatory courses, task qualification, QTPs, and
CDCs required for award of the 3-, 5-, 7-, or 9-skill level.

Utilization and Training Workshop (U&TW). A forum, chaired by the AFCFM and AETC
Training Pipeline Manager (TPM) of MAJCOM Air Force Specialty (AFS) functional managers,
Subject Matter Experts (SMEs), and AETC training personnel that determines career ladder
training requirements.

4
 CFETP 2A6X1A/C/D/E, August 2002

Section A - General Information

1. Purpose. This CFETP provides information necessary for Air Force Career Field Managers
(AFCFMs), MAJCOM functional managers (MFMs), commanders, training managers,
supervisors, and trainers to plan, develop, manage, and conduct an effective career field training
program. This plan outlines the training that individuals in AFSC 2A6X1A/C/D/E should
receive to develop and progress throughout their career. This plan identifies initial skills,
upgrade, qualification, advanced, and proficiency training. Initial skills training is the AFS
specific training an individual receives upon entry into the Air Force or upon retraining into this
specialty for award of the 3-skill level. Normally, this training is conducted by AETC at one or
more of the technical training centers. Upgrade training identifies the mandatory courses, task
qualification requirements, and correspondence course completion requirements for award of the
3-, 5-, 7-, 9-skill levels. Qualification training is actual hands-on task performance training
designed to qualify an airman in a specific duty position. This training program occurs both
during and after the upgrade training process. It is designed to provide the performance
skills/knowledge required to do the job. Advanced training is formal training which provides
individuals who are qualified in one or more positions of their Air Force Specialty (AFS) with
additional skills/knowledge to enhance their expertise in the career field. Supplemental training
is either in-residence or exportable advanced training courses, or on-the-job training. The
CFETP has several purposes, some are:
1.1. Serves as a management tool to plan, manage, conduct, and evaluate a career field training
program. Also, it is used to help supervisors identify training at the appropriate point in an
individual’s career.
1.2. Identifies task and knowledge training requirements for each skill level in the specialty and
recommends education/training throughout each phase of an individual’s career.
1.3. Lists training courses available in the specialty, identifies sources of training, and identifies
the training delivery method.
1.4. Identifies major resource constraints that impact full implementation of the desired career
field training process.

2. Uses. The plan will be used by MFMs and supervisors at all levels to ensure comprehensive
and cohesive training programs are available for each individual in the specialty.
2.1. AETC training personnel will develop/revise formal resident, non-resident, field and
exportable training based on requirements established by the users and documented in Part II of
the CFETP. They will also work with the TPM to develop acquisition strategies for obtaining
resources needed to provide the identified training.
2.2. MFMs will ensure their training programs complement the CFETP mandatory initial,
upgrade, and proficiency requirements. Identified requirements can be satisfied by OJT, resident
training, contract training, or exportable courses. MAJCOM-developed mandatory training to
support this AFS must be identified for inclusion into the plan and must not duplicate other
available training resources.

5
 CFETP 2A6X1A/C/D/E, August 2002

2.3. Each individual will complete the mandatory training requirements specified in this plan.
The lists of courses in Part II will be used as a reference to support training.

3. Coordination and Approval. The AFCFM is the approval authority. MAJCOM

representatives and AETC training personnel will identify and coordinate on the career field
training requirements. The AETC training manager for this specialty will initiate an annual
review of this document by AETC and MFMs to ensure currency and accuracy. Using the list of
courses in Part II, they will eliminate duplicate training.

Section B - Career Progression and Information

4. Specialty Description.
4.1. Specialty Summary. Inspects, maintains, modifies, tests, services, and repairs propellers,
turboprop/turboshaft engines, jet engines, small gas turbine engines, and engine ground support
equipment (SE). Manages aerospace propulsion functions and activities. Related DoD
Occupational Subgroup: 601.
4.2. Duties and Responsibilities.
4.2.1. Plans, organizes, and directs aerospace propulsion maintenance activities. Interprets and
implements directives and publications pertaining to maintenance functions, including
environmentally safe maintenance practices. Determines resource requirements, including
facilities, equipment, and supplies. Inspects and evaluates maintenance activities. Encourages
quality Air Force activities.
4.2.2. Advises, performs troubleshooting, and determines repair procedures on aircraft engines
and propellers. Diagnoses and repairs malfunctions using technical publications. Solves
maintenance problems by studying drawings, wiring and schematic diagrams, technical
instructions, and analyzing operating characteristics or aircraft engines and propellers. Inspects,
certifies, and approves completed maintenance actions.
4.2.3. Removes, installs, inspects, repairs, and modifies engines, engine modules, engine
components, propellers, and propeller components. Disassembles and assembles engines and
propellers adhering to prescribed procedures. Prepares engines and propellers for installation,
storage, or transportation. Tests components using bench mockups and test equipment. Installs
and removes engines on test stands, and operates, evaluates, and performs test stand functions on
engines. Accomplishes operator maintenance on test stands. Inspects and maintains engine
ground SE. Operates and performs operator inspections on related SE. Selects, uses, and cares
for special tools, and hand tools, and test equipment. Uses and disposes of hazardous waste
materials adhering to prescribed procedures.
4.2.4. Analyze, interpret, and recommend maintenance actions based on unscheduled engine
removals and engine monitoring system data. Coordinate with the base engine manager to
analyze scheduled engine removals; recommend forecast actions to the weekly or monthly
maintenance schedules.

5. Skill/Career Progression. Adequate training and timely progression from the apprentice to
the superintendent skill level play an important role in the Air Force’s ability to accomplish its
mission. It is essential that everyone involved in training do their part to plan, manage, and
conduct an effective training program. The guidance provided in this part of the CFETP will

6
 CFETP 2A6X1A/C/D/E, August 2002

ensure each individual receives necessary training at appropriate points in their career. The
following narrative and AFSC 2A6X1A/C/D/E career field table identify the skill/career
progression.
5.1. Apprentice (3) Level. Following Basic Military Training, initial skills training will be
provided in a resident course at the 82d Training Group, 361st Training Squadron, Sheppard Air
Force Base, Texas. The course will lay the foundation for additional training at the graduate's
first duty assignment. Trainees will utilize the Career Development Course (CDC), task
qualification training, and other exportable courses to progress in their career field. Once the
trainee is task certified, the trainee may perform the task unsupervised.
5.2. Journeyman (5) Level. Once upgraded to the 5-level, the journeyman will enter into
continuation training to broaden their experience base by increasing their knowledge and skill in
troubleshooting and solving more complex problems. Five-levels may be assigned job positions
such as quality assurance and various staff positions. After having 48 months in the Air Force, 5-
levels will attend Airman Leadership School (ALS) to enhance their Professional Military
Education (PME). Five levels will be considered for appointment as unit trainers. Individuals
will use their CDCs to prepare for Weighted Airman Promotion testing. They should also
consider continuing their education toward a Community College of the Air Force (CCAF)
degree.
5.3. Craftsman (7) Level. A craftsman can expect to fill various supervisory and management
positions such as shift leader, element chief, shop chief, task certifier, and various staff positions.
Exportable MDS specific courses and MAJCOM/unit directed courses are also available. Seven-
levels should take courses or obtain added knowledge of management of resources and
personnel. Continued academic education through CCAF and higher degree programs is
encouraged. In addition, when promoted to TSgt, individuals will attend the Noncommissioned
Officer Academy.
5.4. Superintendent (9) Level. A 9-level can be expected to fill positions such as flight chief,
production supervisor, and various staff NCOIC jobs. Additional training in the areas of budget,
manpower, resources, and personnel management should be pursued through continuing
education. Individuals promoted to SMSgt will attend the Senior Noncommissioned Officer
Academy. Additional higher education and completion of courses outside their career AFS is
also recommended.
6. Training Decisions. The CFETP uses a building block approach (simple to complex) to
encompass the entire spectrum of training requirements for the Aerospace Propulsion Jet Engine
career field. The spectrum includes a strategy for when, where, and how to meet these training
requirements. The strategy must ensure we develop affordable training, eliminate duplication,
and prevent a fragmented approach to training. The following training decisions were based on a
career field utilization and training workshop at Sheppard Air Force Base, Texas from
25-29 June 2001.
6.1. Initial Skills. Minor changes to the 3-level courses for AFSC 2A6X1A included adding:
knowledge of TCTOs, operation of personnel stands, use of flex borescope, knowledge of small
gas turbines and auxiliary power units, and knowledge of bearing handling. The proficiency
level was decreased from 2b to 1b for: CAMS, SBSS, JDD, and 781 series forms to provide for
more hands-on training time on the engines.
6.2. Five Level Upgrade Requirements. The 5-level CDCs were revised to include needed
material with emphasis in the following areas: Aircraft safe for maintenance, TCTO’s, supply

7
 CFETP 2A6X1A/C/D/E, August 2002

documents management, equipment account management, depot level repairable/reparable

support division, engine historical records, engine status reports, vacuum/pneumatic tester,
operate personnel stands, operate and maintain test stand, and bearing handling. The following
5-level core tasks were deleted: Use multimeter, fuel pump removal and installation, and
gearbox removal and installation. The following 5-level core tasks were added: Use technical
pubs, job data documentation, AFTO Form 350, AFTO Form 781 series, select and use
handtools, select and use engine hardware, use hardware safety devices, preliminary maintenance
procedures on: work area, support equipment, and engine. The following 5-level core tasks were
changed: Engine rigging was changed to a 7-level core task and fuel control removal and
installation was changed from a “*” to a “*/R”.
6.3. Seven Level Upgrade Requirements. Major changes occurred in both the 7-level CDC
and in-residence courses. The 7-level CDCs were revised to emphasize: Supervision and
Management topics along with the following knowledge items: FOD program manager, enlisted
specialty training requirements, AFTO Form 22, maintenance supply concept, logistics
maintenance management, resource management, mobility, maintenance accountability for forms
documentation (JDD/781s), vacuum pneumatic tester, use rigid and flex borescope, damage
analysis, and vibration analysis. The 7-level in-residence course was revised to concentrate on
supervision and management issues directly relating to the propulsion career field. The
following topics will be covered in the 7-level in-residence course: Enlisted specialty training
program, logistics maintenance management, resource management, maintenance accountability
for forms documentation, advanced engine operating principles, electrical and mechanical engine
controls, engine status reports, engine historical records, use of 781 form series, engine
performance, engine monitoring system trend data, damage analysis, read and interpret
schematics and use the reliability centered maintenance (RCM) calculator. Hazardous materials
program, use of the multimeter ,and multi-system troubleshooting were deleted from the in-
residence course. The following 7-level core tasks were deleted: Prepare teaching outline,
provide trainee theory, give feedback on training, develop methods of evaluation, use appropriate
methods of evaluation, give supervisor and trainer feedback on results of training, use rigid
borescope, and compressor (Fan) repair. The following 7-level core tasks were added: engine
rigging and augmenter inspection.
6.4. Continuation Training. Any additional knowledge and skill requirements which were not
taught through initial or upgrade training are assigned to unit training or Training Detachments.
The purpose of the continuation training program is to provide additional training exceeding
minimum upgrade training requirements with emphasis on present and future duty position.
MAJCOMs develop a proficiency training program that ensures individuals in the Aerospace
Propulsion Jet Engine career field receive the necessary training at the appropriate point in their
career. The program identifies both mandatory and optional training requirements.

7. Community College of the Air Force. Enrollment in CCAF occurs upon completion of
basic military training. CCAF provides the opportunity to obtain an Associates in Applied
Sciences Degree. In addition to its associates degree program, CCAF offers the following:
7.1. Occupational Instructor Certification. Upon completion of instructor qualification
training, consisting of the Basic Instructor Course (BIC) and supervised practice teaching, CCAF
instructors who possess an associates degree or higher may be nominated by their school
commander/commandant for certification as an occupational instructor.

8
 CFETP 2A6X1A/C/D/E, August 2002

7.2. Trade Skill Certification. When a CCAF student separates or retires, a trade skill
certification is awarded for the primary occupational specialty. The College uses a competency
based assessment process for trade skill certification at one of four proficiency levels:
Apprentice, Journeyman, Craftsman/Supervisor, or Master Craftsman/Manager. All are
transcribed on the CCAF transcript.
7.3. Degree Requirements. All airmen are automatically entered into the CCAF program.
Prior to completing an associates degree, the 5-level must be awarded and the following
requirements must be met:

Semester Hours
Technical Education 24
Leadership, Management, and Military Studies 6
Physical Education 4
General Education 15
Program Elective 15
(Technical Education; Leadership, Management, and Military Studies;
or General Education)

Total 64

7.3.1. Technical Education (24 Semester Hours): Completion of the J3AQR2A611 001course
and J3ABR2A631C 001, J3ABR2A631D 007, or J3ABR2A631E 006 courses satisfy some
semester hours of the technical education requirements. A minimum of 12 semester hours of
Technical Core subjects/courses must be applied and the remaining semester hours applied from
Technical Core/Technical Elective courses.
7.3.2. Leadership, Management, and Military Studies (6 Semester Hours): Professional
military education and/or civilian management courses.
7.3.3. Physical Education (4 Semester Hours): This requirement is satisfied by completion of
Basic Military Training.
7.3.4. General Education (15 Semester Hours): Applicable courses must meet the criteria for
application of courses to the General Education Requirements (GER) and be in agreement with
the definitions of applicable General Education subjects/courses as provided in the CCAF
General Catalog.
7.3.5. Program Elective (15 Semester Hours): Satisfied with applicable Technical Education;
Leadership, Management, and Military Studies; or General Education subjects/courses, including
natural science courses meeting GER application criteria. Six semester hours of CCAF degree
applicable technical credit otherwise not applicable to this program may be applied. See the
CCAF General Catalog for details regarding the Associates of Applied Science for this specialty.
7.4. AETC Instructor Requirements: Additional off-duty education is a personal choice that
is encouraged for all. Individuals desiring to become an Air Education and Training Command
instructor should be actively pursuing an associates degree. A degreed faculty is necessary to
maintain accreditation through the Southern Association of Colleges and Schools.

9
 CFETP 2A6X1A/C/D/E, August 2002

8. Career Field Path.

8.1. Enlisted Career Path: Table 8.1. identifies career milestones for the 2A6X1A/C/D/E Air
Force specialty.

Table 8.1. Enlisted Career Path

Grade Requirements
Education and Training Requirements Rank Average Earliest High Year Of Tenure
Sew-On Sew-On (HYT)
Basic Military Training School
Apprentice Technical School (3-Skill Level) Amn 6 months
A1C 16 months
Upgrade To Journeyman (5-Skill Level) Amn 6 months
- Minimum 15 months on-the-job training. A1C 16 months
- Complete all 5-level core tasks on one mission SrA 3 years 28 months 10 Years
design series.
- Complete appropriate CDC if/when available.
Airman Leadership School (ALS)
- Must be a SrA with 48 months time in service
or be a SSgt Selectee.
- Resident graduation is a prerequisite for SSgt
sew-on (Active Duty Only).
Trainer Certifier
- Qualified and certified to perform the task to - Be at least a 5-skill level SSgt; and qualified and certified
be trained. to perform the task being certified.
- Have attended the formal trainer’s course and - Attend formal certifier course and appointed in writing by
appointed in writing by Commander. Commander.
- Be a person other than the trainer.
Upgrade To Craftsman (7-Skill Level) SSgt 7.5 years 3 years 20 Years
- Minimum rank of SSgt.
- Complete all 5- and 7-level core tasks on one
mission design series.
- Complete appropriate CDC if/when available.
- Advanced Technical School.
- Minimum 12 months on-the-job training.
Noncommissioned Officer Academy (NCOA) TSgt 12.5 years 5 years 22 Years
- Must be a TSgt or TSgt Selectee.
- Resident graduation is a prerequisite for MSgt
sew-on (Active Duty Only). MSgt 16 years 8 years 24 Years
USAF Senior NCO Academy (SNCOA) SMSgt 19.2 years 11 years 26 Years
- Must be a SMSgt or SMSgt Selectee.
- A percentage of top non-select (for promotion
to E-8) MSgts attend the SNCOA each year.
- Resident or correspondence graduation is a
prerequisite for CMSgt sew-on.
Upgrade To Superintendent (9-Skill Level) CMSgt 21.5 years 14 years 30 Years
- Minimum rank of SMSgt.

10
 CFETP 2A6X1A/C/D/E, August 2002

8.2. Base/Unit Education and Training Manager Checklist:

Table 8.2. Base/Unit Education and Training Manager Checklist

Requirements for Upgrade to: Y N
Journeyman
- Has the apprentice completed mandatory CDCs, if available?
- Has the apprentice completed all appropriate 5-level core tasks identified in the CFETP?
- Has the apprentice completed all other duty position tasks identified by the supervisor?
- Has the apprentice completed 15 months training (9 months for retrainees) for award of the
5-skill level?
- Has the apprentice met mandatory requirements listed in specialty description,
AFMAN 36-2108, (Airman Classification), and the CFETP?
- Has the apprentice completed mandatory CAMS CBT J6ANU00066-043, CAMS For Flightline
and Backshop? (not required for units using GO81)
(Exception: AMC and AMC gained ANG/AFRC Personnel).
- Has the apprentice been recommended by their supervisor?
Craftsman
- Has the journeyman achieved the rank of SSgt?
- Has the journeyman completed mandatory CDCs?
- Has the journeyman completed all core tasks identified in the CFETP?
- Has the journeyman completed all other duty position tasks identified by the supervisor?
- Has the journeyman attended 7-skill level Craftsman Course?
- Has the journeyman completed a minimum 12 months UGT for award of the 7-skill level?

TO: Squadron/CC

FROM: Squadron Training Manager

SUBJECT: Upgrade Trainee

Trainee is prepared to be upgraded and has completed all training requirements.

_______________________ _______________________
Training Manager Supervisor

11
 CFETP 2A6X1A/C/D/E, August 2002

Section C - Skill Level Training Requirements

9. Purpose. Skill level training requirements in the 2A6X1A/C/D/E career field are defined in
terms of tasks and knowledge requirements. This section outlines the specialty qualification
requirements for each skill level in broad, general terms and establishes the mandatory
requirements for entry, award, and retention of each skill level. The specific task and knowledge
training requirements are identified in the STS at Part II, Sections A and B of this CFETP.

10. Specialty Qualification:

10.1. Apprentice Level Training:
10.1.1. Specialty Qualification. This information is located in the official specialty description
in AFMAN 36-2108, paragraph 3.
10.1.1.1. Knowledge. To perform the duties at the 3-skill level, an individual must be able to
understand basic system theory of operation and be able to perform certain organizational
maintenance level tasks under close supervision until they are task certified. A 3-level must be
able to use technical data, common hand tools, and special test equipment. Apprentices must be
qualified to remove and install system components, perform engine/propeller change, use SE,
trace system schematic flow on system schematic diagrams, and document maintenance actions
in the automated data system.
10.1.1.2. Education. For entry into this specialty, completion of high school with courses in
general science, mechanics, or mathematics is desirable.
10.1.1.3. Training. For award of AFSC 2A631C/D/E, completion of the J3AQR2A611 001,
Aerospace Propulsion Apprentice Jet Engine course is mandatory.
10.1.1.4. Experience. None.
10.1.2. Training Sources and Resources. The 3-level initial skills course will provide the
required knowledge, qualification, and, if applicable, certification. Initial skills training
encompasses jet engine theory and operating principles, system operation, component removal
and operation, introduction to general flight line maintenance practices, use of technical
publications, maintenance documentation, and support equipment familiarization and use.
10.1.3. Implementation. Upon graduation from Basic Military Training (BMT), completion of
J3AQR2A611 001 and J3ABR2A631C 001, J3ABR2A631D 007, or J3ABR2A631E 006 is
required to satisfy the knowledge and training resource requirements for award of the 3-skill
level.
10.2. Journeyman Level Training:
10.2.1. Specialty Qualification. This information is located in the official specialty description
in AFMAN 36-2108, paragraph 3.
10.2.1.1. Knowledge. In addition to the 3-level qualifications, a 5-skill level must possess the
knowledge and skill necessary to maintain jet engines. A 5-level must be task qualified on
inspecting jet engine components, systems, correcting system malfunctions, repairing and
replacing system components, operational checks, and the use and maintenance of test and
support equipment.
10.2.1.2. Education. There are no additional education requirements beyond those defined for
the apprentice level. However, completion of a CCAF degree is desirable.
10.2.1.3. Training. For award of AFSC 2A651A/C/D/E, the 5-level CDC provides the career
knowledge training required. Qualification training and OJT will provide training and

12
 CFETP 2A6X1A/C/D/E, August 2002

qualification on the core tasks identified in the STS. The CDC is written to build from the
trainee's current knowledge base, and provides more in-depth knowledge to support OJT
requirements.
10.2.1.4. Experience. Qualification in and possession of AFS 2A631. Completion of all 5-level
core tasks identified in the STS is mandatory.
10.2.2. Training Sources and Resources. A minimum of 15 months on-the-job training,
completion of the 2A651A CDC, and completion of 5-level core tasks represent the resources
needed for award of the 5-skill level.
10.2.3. Implementation. Training to the 5-level is performed by the units utilizing this STS,
exportable courses, and CDCs. Upgrade to the 5-level requires completion of CDC 2A651A and
15 months upgrade training.
10.3. Craftsman Level Training:
10.3.1 Specialty Qualification. This information is located in the official specialty description
in AFMAN 36-2108, paragraph 3.
10.3.1.1. Knowledge. A 7-level must possess advanced skills and knowledge of: theory,
concepts, principles, and application of engine maintenance. The 7-level must be able to
supervise and train personnel to maintain jet engines. The 7-level must be able to plan, schedule,
and organize maintenance to ensure effective utilization of available resources. Qualification is
required on advanced repair, inspection, troubleshooting, and diagnostic techniques. Historical
documentation analysis is also required for all 7-levels.
10.3.1.2. Education. There are no additional education requirements beyond those defined for
the apprentice level. However, completion of a CCAF degree is desirable.
10.3.1.3. Training. Completion of the mandatory 2AX7X CDCs, 7-level core tasks, and the
resident 7-level course are mandatory for upgrade to 2A671A.
10.3.1.4. Experience. Qualification in and possession of AFS 2A651A. Completion of all 5-
and 7-level core tasks identified in the STS is mandatory.
10.3.2. Training Sources and Resources. Completion of the J3ACR2A671A 003, Aerospace
Propulsion Craftsman, Jet Engine course, completion 2AX7X CDCs, along with supervisor
certification of Air Force directed core tasks represent the resources required for award of the 7-
skill level. The Course Objective List (COL) listed in Part II lists the training rendered at the 7-
level resident course at Sheppard Air Force Base, Texas.
10.3.3. Implementation. Upgrade to the 7-level will require completion of all AF core tasks, 12
months OJT as a SSgt, completion of the 7-level 2AX7X CDC (as a prerequisite) and resident 7-
level course at Sheppard Air Force Base, Texas. Completion of all 5- and 7-level core tasks, and
2AX7X CDCs, and 12 months OJT as a SSgt will be completed before attending the resident
course.
10.4. Superintendent Level Training:
10.4.1 Specialty Qualification. This information is located in the official specialty description
in AFMAN 36-2108, paragraph 3.
10.4.1.1. Knowledge. Knowledge is mandatory of: advanced skills and knowledge of concepts
and principles in the management of aircraft propulsion systems. The 9-level must be an
effective leader and must be able to manage funding and other assigned resources. They must
also be knowledgeable of all environmental standards and ensure adherence to the proper
handling and disposal of hazardous materials and waste.

13
 CFETP 2A6X1A/C/D/E, August 2002

10.4.1.2. Education. There are no additional education requirements beyond those defined for
the apprentice level. However, completion of a CCAF degree is desirable.
10.4.1.3. Training. For award of AFSC 2A691, completion of the Senior NCO Academy in
residence and unit OJT is mandatory.
10.4.1.4. Experience. For award of AFSC 2A691, qualification in and possession of AFSC
2A671A or 2A671B is mandatory. Also, experience in managing or directing repair activities for
aerospace aircraft engines, propellers, and associated maintenance functions.
10.4.1.5. Other. Not Used.
10.4.2. Training Sources/Resources. Instruction received at the Senior NCO Academy and
duty position qualification represent the required resources for upgrade to the 9-skill level.
10.4.3. Implementation. The 9-level will be awarded after promotion to SMSgt.

Section D - Resource Constraints

11. Purpose. This section identifies known resource constraints which preclude optimal/desired
training from being developed or conducted, including information such as cost and manpower.
Narrative explanations of each resource constraint and an impact statement describing what
effect each constraint has on training are included. Also included in this section are actions
required, office of primary responsibility, and target completion dates. Resource constraints will
be, as a minimum, reviewed and updated annually.

12. Apprentice Level Training: The J3ABR2A631C 002 course is constrained by manpower
authorizations necessary to fund the additional student man-years and instructors.

13. Five Level Training: There are no 5-level constraints.

14. Seven-Level Training. There are no 7-level constraints.

Section E. - Transitional Training Guide. There are no transition training requirements.

14
 CFETP 2A6X1A/C/D/E, August 2002

PART II

Section A - Specialty Training Standard

1. Implementation. This STS will be used for technical training provided by Air Education and
Training Command for the following classes: Course J3ABR2A631D 007 (F100) will begin
with 03010 (17 Jan 03) with a graduation date of 21 April 2002. Course J3ABR2A631E 006
(F110) will begin with class 03008 (10 Jan 03) with a graduation date of 14 April 2003. Course
J3ABR2A631C 002 (TF33, TF 34, F108) will begin with class 03031 (17 Jan 03) with a
graduation date of 01 April 2003. The 7-level J3ACR2A671A 003 (Craftsman) course will
continue unchanged.

2. Purpose of this STS. As prescribed in AFI 36-2201, this STS:

2.1. Lists in column 1 (Tasks, Knowledge, and Technical References) the most common tasks,
knowledge, and technical references (TR) necessary for airmen to perform duties in the 3-, 5-,
and 7-skill level.
2.2. Identifies in column 2 (Core Tasks), by asterisk (*), specialty-wide training requirements.
MAJCOM Functional Managers, commanders, and supervisors may designate additional critical
tasks as necessary. When designated, certify these critical tasks using normal core task
certification procedures. As a minimum, certification on all AFCFM directed core tasks
applicable to the specialty must be completed for skill level upgrade. Exemptions:
2.2.1. Core tasks which are not applicable to base assigned aircraft or equipment are not required
for upgrade (units are not required to send personnel TDY for core task training).
2.2.2. For units with more than one mission design (e.g. A-10) aircraft, upgrade trainees need
only complete core tasks on a single mission design. MFMs, unit commanders, and/or
supervisors may require trainees to complete core task training on additional mission design
aircraft, if desired. If some of these core tasks involve training in another unit on base, trainees
must still complete all core tasks relevant to at least one mission design aircraft. All units are
bound by the requirements in this CFETP and will accommodate core task trainees from other
units.
2.2.3. Units that use the GO81 maintenance data collection system do not need to complete Core
Automated Maintenance System (CAMS) Computer Based Training (CBT) core tasks.
However, these units must be capable of training CAMS related CBT core tasks for deployment
preparation. This capability ensures GO81 users are capable of operating CAMS prior to
deploying to CAMS using units.
2.3. Provides certification for OJT. Column 3 is used to record completion of tasks and
knowledge training requirements. Use automated training management systems to document
technician qualifications, if available. Task certification must show a certification completed
date.
2.4. Shows formal training and correspondence course requirements. Column 4 shows the
proficiency to be demonstrated on the job by the graduate as a result of training on the
task/knowledge and the career knowledge provided by the correspondence course. When two
codes are used in columns 4A and 4C (e.g. 2b/b), the first code is the established requirement for
resident training on the task/knowledge and the second code indicates the level of training

15
 CFETP 2A6X1A/C/D/E, August 2002

provided in the course due to equipment shortages or other resource constraints. See
CADRE/AFSC/CDC listing maintained by the unit training manager for current CDC listing.
2.5. Qualitative Requirements. Attachment 1 contains the proficiency code key used to
indicate the level of training and knowledge provided by resident training and career
development courses.
2.6. Job Qualification Standard. Becomes a Job Qualification Standard (JQS) for on-the-job
training when placed in the AF Form 623, On-the-Job Training Record, and used according to
AFI 36-2201. For OJT, the tasks in column 1 are trained and qualified to the go/no go level.
"Go" means the individual can perform the task without assistance and meets local requirements
for accuracy, timeliness, and correct procedures. When used as a JQS, the following
requirements apply:
2.6.1. Documentation. Document and certify completion of training IAW AFMAN 36-2201.
Automated records, utilizing Core Automated Management System (CAMS) reflecting this STS
may be used and is highly encouraged. Use of attachments one, two, and twelve are mandatory
in individual training records along with CFETP Part I and Part II, Section A. Identify duty
position requirements by circling (in pencil) the subparagraph number next to the task statement.
As a minimum, complete the following columns in Part II of the CFETP: date training
completed, trainee initials, and trainer initials. Third party certifications of core tasks is no
longer an Air Force requirement for this specialty. However, MAJCOM functional managers,
commanders, and supervisors may still designate critical tasks as requiring third party
certification. There are no approved AFJQSs for this AFSC.
2.6.1.1. Converting from Old Document to CFETP. All AFJQSs and previous CFETPs are
replaced by this CFETP; therefore, conversion of all training records to this CFETP STS is
mandatory. Use this CFETP STS (or automated STS) to identify and certify all past and current
qualifications.
2.6.1.1.1. For those core and critical tasks previously certified and required in the current duty
position, evaluate current qualifications and, when verified, recertify using current date as
completion date and enter trainee’s and certifier’s initials. Remember, during the transcription
process, no training is taking place. Therefore, the trainer’s initials are not required.
2.6.1.1.2. For non-core and non-critical tasks previously certified and required in the current
duty position, evaluate current qualifications and when verified, recertify using current date as
completion date and enter trainee’s and trainer’s initials.
2.6.1.1.3. When transcribing previous certification for tasks not required in the current duty
position, carry forward only the previous completion date of certification (not the initials of
another person). If and when transcribed tasks become duty position requirements, recertify
using standard certification procedures.
2.6.1.1.4. The person whose initials appear in the trainer or certifier block during the
transcription process must meet the requirements of their respective roles.
2.6.1.1.5. Upon completion of the transcription process, give the old CFETP to the member.
2.6.1.2. Documenting Career Knowledge. When a CDC is not available: the supervisor
identifies CFETP, Part II training references that the trainee requires for career knowledge and
ensures, as a minimum, that trainers cover the mandatory items in AFMAN 36-2108. For two-
time CDC course exam failures: Supervisors identify all Part II items corresponding to the areas
covered by the CDC. The trainee completes a study of references, undergoes evaluation by the

16
 CFETP 2A6X1A/C/D/E, August 2002

task certifier, and receives certification on the CFETP, Part II. Supervisors must document
successful completion of career knowledge prior to submission of a CDC waiver.
2.6.1.3. Decertification and Recertification. When an airman is found to be unqualified on a
task previously certified for his or her position, the supervisor lines through the previous
certification or deletes previous certification when using an automated system. Appropriate
remarks are entered on the AF Form 623A, On-The-Job Training Record Continuation Sheet,
as to the reason for decertification. The individual is recertified (if required) either by erasing the
old entries and writing in the new or by using correction fluid/tape (if entries were made in ink)
over the previously certified entry.
2.6.2. AF Form 797. When additional items not listed in the CFETP, Part II are necessary in the
current duty assignment, enter them on the AF Form 797. Fill out the form IAW AFMAN
36-2247.
2.6.3. Disposition of Training Records. Upon separation, retirement, commissioning, or
promotion to Master Sergeant (unless otherwise directed by the AFCFM, MAJCOM, unit
commander, or supervisor), give the individual their training records. Also, give individuals
outdated training records after transcribing records. Do not remove any training records that
show past qualifications unless transcribed to a new CFETP/AFJQS. For example, an individual
working in a tool crib must maintain documented career field qualifications in case they return to
duty on the flightline or in the shop. Supervisors must exercise good judgment when removing
training records not needed in current duty positions.
2.7. Specialty Training Standard. Is a guide for development of promotion tests used in the
Weighted Airman Promotion System (WAPS). Specialty Knowledge Tests (SKTs) are
developed at the USAF Occupational Measurement Squadron by senior NCOs with extensive
practical experience in their career fields. The tests sample knowledge of STS subject matter
areas judged by test development team members as most appropriate for promotion to higher
grades. Questions are based upon study references listed in the WAPS catalog. WAPS is not
applicable to the Air National Guard or Air Force Reserve.

3. Recommendations: Report unsatisfactory performance of individual course graduates to the

AETC training manager at 361 TRS/TRR, 501 Missile Road, Sheppard AFB TX, 76311-2264,
DSN 736-3545. Reference specific STS paragraphs. A customer service information line has
been installed for the supervisor’s convenience to identify graduates who may have received over
or under training on task/knowledge items listed in this training standard. For a quick response
to problems, call our customer service information line, DSN 736-5236, any time, day or night.

BY ORDER OF THE SECRETARY OF THE AIR FORCE

OFFICIAL MICHAEL E. ZETTLER, Lieutenant General, USAF

DCS/Installations and Logistics

17
 CFETP 2A6X1A/C/D/E, August 2002

12 Attachments
1. Proficiency Code Key
2. STS – 2A6X1A/C/D/E
3. STS – 2A6X1D/E only
4. STS – 2A6X1C only
5. STS – TF39 C-5 only
6. STS – JT8 C-9 only
7. STS – F108 KC-135R/T/ only
8. STS –CF6-50 KC-10 only
9. STS – F117 C-17 only
10. STS – TF33 C-141/KC-135E only
11. STS – Secondary Power/APU
12. STS – 2AX7X

18
 PROFICIENCY CODE KEY
CFETP 2A6X1A/C/D/E, August 2002
This Block Is For Identification Purposes Only
Name Of Trainee
Printed Name (Last, First, Middle Initial) Initials (Written) SSAN

Printed Name Of Training/Certifying Official And Written Initials

N/I N/I

N/I N/I

N/I N/I

N/I N/I

N/I N/I

N/I N/I

N/I N/I

N/I N/I

QUALITATIVE REQUIREMENTS
Proficiency Code Key
Scale Definition: The individual
Value
1 IS EXTREMELY LIMITED (Can do simple parts of the task. Needs to be told or shown how to do most
of the task.)
Task 2 IS PARTIALLY PROFICIENT (Can do most parts of the task. Needs only help on hardest parts.)

Performance 3 IS COMPETENT (Can do all parts of the task. Needs only a spot check of completed work.)

Levels 4 IS HIGHLY PROFICIENT (Can do the complete task quickly and accurately. Can tell or show others
how to do the task.)
a KNOWS NOMENCLATURE (Can name parts, tools, and simple facts about the task. )

*Task b KNOWS PROCEDURES (Can determine step by step procedures for doing the task. )

Knowledge c KNOWS OPERATING PRINCIPLES (Can identify why and when the task must be done and why each
step is needed.)
Levels d KNOWS ADVANCED THEORY (Can predict, isolate, and resolve problems about the task.)

A KNOWS FACTS (Can identify basic facts and terms about the subject.)

**Subject B KNOWS PRINCIPLES (Can identify relationship of basic facts and state general principles about the
subject.)
Knowledge C KNOWS ANALYSIS (Can analyze facts and principles and draw conclusions about the subject.)

Levels D KNOWS EVALUATION (Can evaluate conditions and make proper decisions about the subject.)
Explanations
* A task knowledge scale value may be used alone or with a task performance scale value to define a level of knowledge for a specific task. (Example: b and 1b)

** A subject knowledge scale value is used alone to define a level of knowledge for a subject not directly related to any specific task, or for a subject common to
several tasks.

- This mark is used alone instead of a scale value to show that no proficiency training is provided in the courses or CDCs.

/ This mark is used in course columns to show that training is required but not given due to limitations in resources (3c/b, 2b/b etc.).

Note: Tasks and knowledge items shown with an asterisk (*) in column one are trained during wartime. The 7-level course is not taught during wartime.

19 Attachment 1
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
ATTACHMENT 2
NOTE 1: The tasks and knowledge listed in attachment 2 are performed by all personnel in the Aerospace Propulsion specialty for the appropriate skill level
upgrade. The task in attachments 3 through 11 are engine specific and are to be performed by all personnel in the Aerospace Propulsion specialty performing
maintenance on the specified equipment. The tasks in both attachment 2 and the additional attachment(s) are to be documented for skill level UGT.

NOTE 2: In addition to attachment 2, the tasks and knowledge listed in attachment 3 are performed by personnel in the apprentice (3-level)
J3ABR2A631D 007 (F100) and J3ABR2A631E 006 (F110) courses.
NOTE 3: In addition to attachment 2, the tasks and knowledge listed in attachment 4 are performed by personnel in the apprentice (3-level)
J3ABR2A631C 001 (TF33, TF34, F108) course.

NOTE 4: J3ABR2A631D 007 (F100), J3ABR2A631E 006 (F110) and J3ABR2A631C 002 (TF33, TF34, F108) are Mission Ready Airman courses.

NOTE 5: Use paragraph references A2.11.3., A2.11.3.1., A2.11.3.2., A2.11.4., A2.11.4.1., and A2.11.4.2. for the specific system used at each base.

NOTE 6: Due to equipment design, tasks A2.21.4.7., A2.21.4.8., and A2.21.5.4. won’t be taught in the 3-level F100 and F110 apprentice courses.
NOTE 7: Tasks and knowledge identified by an asterisk (*) in column 1 are trained in the resident wartime courses when implemented.
A2.1. CAREER FIELD PROGRESSION - A - -
TR: AFI 36-2101

A2.2. AF OCCUPATIONAL SAFETY AND

HEALTH (AFOSH) PROGRAM
TR: AFI 127-01 Vol 1 and 3;
AFIs 21-101, 91-202, 91-204, 91-213,
91-301, 91-302, AFPAM 91-215;
AFOSH STD 91-301 and applicable
aircraft/engine TOs

A2.2.1. AFOSH standards for AFSC 2A6X1A A B - -

*A2.2.2. Hazards of AFSC 2A6X1A * A B - -

A2.2.3. Aircraft safe for maintenance - B - -

*A2.2.4. Keep work area safe * 2b B - -

A2.2.5. Select/use restraint harness (e.g., Fall - - - -

protection/prevention equipment)

A2.2.6. Operational Risk Management (ORM) - B - -

A2.2.7. Maintenance incident prevention and - - - -

investigation

*A2.3. OPERATIONS SECURITY (OPSEC) A - - -

VULNERABILITIES FOR AFSC
2A6X1A/C/D/E
TR: AFI 10-1101

A2.4. FOREIGN OBJECT DAMAGE (FOD)

PROGRAM
TR: AFI 21-101 and applicable
MAJCOM instructions

*A2.4.1. FOD prevention program * B B - -

A2.4.2. FOD Program Manager - - - -

A2.4.3. Dropped Object Prevention Program - - - -

(DOPP)

20
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A2.5. HAZARDOUS MATERIALS AND
WASTE HANDLING ACCORDING
TO ENVIRONMENTAL STANDARDS
TR: AFJMAN 24-204

A2.5.1. Initial Federal Hazard Communication - - - -

Training Program

*A2.5.2. Hazardous Materials Program A B - -

*A2.5.3. Types of hazardous materials/fluids A B - -

*A2.5.4. Handling procedures A B - -

*A2.5.5. Storage and labeling A B - -

*A2.5.6. Proper disposal A B - -

A2.6. ENLISTED SPECIALTY TRAINING

TR: AFIs 36-2201 and 36-2232 and
applicable MAJCOM directives

*A2.6.1. Training requirements - - - B

A2.6.2. OJT trainer requirements

A2.6.2.1. Prepare teaching outlines or task - - - -

breakdowns

A2.6.2.2. Provide trainee theory and train on - - - -

actual equipment

A2.6.2.3. Give feedback on training provided - - - -

A2.6.3. OJT task certifier requirements

A2.6.3.1. Develop methods of evaluation to - - - -

determine trainee knowledge/
qualification, and training effectiveness

A2.6.3.2. Use appropriate method of evaluation - - - -

and effectively determine trainee’s
ability

A2.6.3.3. Give supervisor and trainer feedback on - - - -

results of training provided, and
trainee’s strengths/weaknesses

A2.6.4. Training plans and working groups - - - -

A2.7. TECHNICAL PUBLICATIONS

TR: AFPD 21-3, TOs 00-5-1, 00-5-2,
and 00-5-15

*A2.7.1. TO system B B - -

*A2.7.2. Use technical pubs * 2b B - -

A2.7.3. TCTOs A B - -

A2.7.4. AFTO Form 22 A B - -

A2.8. SUPPLY MANAGEMENT

TR: AFMAN 23-110 and TOs 00-20-3
and 00-20K-1

21
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
*A2.8.1. Maintenance supply concept A B - -
(include Regional Supply System)

A2.8.2. Supply documents management - A - -

A2.8.3. Status tags A B - -

A2.8.4. AF Form 2005 A B - -

A2.8.5. Equipment account management - A - -

A2.8.6. Depot Level Reparable (DLR)/ - A - -

Reparable Support Division (RSD)

A2.8.7. Priority system A B - -

A2.8.8. Repair cycle assets - B - -

A2.8.9. Inspect and control USAF shelf-life - B - -

items

A2.8.10. Precious Metal Recovery - - - -

A2.9. MAINTENANCE MANAGEMENT

TR: AFI 21-101, TOs 00-35D-54,
00-20 series, AFMCI 21-103,
AFMAN 21-104 and applicable
MAJCOM directives

A2.9.1. Responsibilities of the Operations/ - A - -

Logistics Group Commander

A2.9.2. Functions within the Maintenance - A - -

complex

A2.9.3. Engine maintenance management - A - -

information systems

*A2.9.4. Logistics maintenance management - - - B

*A2.9.5. Resource management - - - B

A2.9.6. Mobility - A - -

*A2.9.7. Maintenance accountability - - - B

A2.9.8. Process PMEL equipment - - - -

A2.9.9. Personal Computers (PCs) - - - -

A2.9.10. Status of Reports and Training (SORTS) - - - -

A2.9.11. Land Mobile Radios (LMR) - - - -

A2.9.12. Classified asset handling - - - -

A2.9.13. Reliability Centered Maintenance A B - -

(RCM)

A2.9.14. Use RCM Calculator - - - b

A2.10. PROVIDE AND INTERPRET DATA

TR: AFCSM 21 series and TO 00-20
series, TO 00-25-254-1/-2

A2.10.1. Engine historical records A B - B

22
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A2.10.2. Engine status reports - B - B

A2.11. MAINTENANCE SYSTEMS,

INSPECTION SYSTEMS AND
FORMS
TR: AFCSM 21 series, AFI 21-101;
TOs 00-20 series, 00-35D-54;
applicable aircraft work unit code
manuals and applicable MAJCOM
directives

A2.11.1. Maintenance systems - B - -

A2.11.2. Inspection systems - B - -

A2.11.3. CAMS

A2.11.3.1. Principles A

A2.11.3.2. Use CAMS * 1b - - -

A2.11.3.3. Use Standard Base Supply Systems 1b - - -

(SBSS)

A2.11.4. GO81

A2.11.4.1. Use GO81 * - - - -

A2.11.4.2. Use SBSS - - - -

A2.11.5. Document maintenance actions

A2.11.5.1. Use Job Data Documentation (JDD) * 1b - - -

screens

A2.11.5.2. Use AFTO Form 350 * 2b - - -

A2.11.5.3. Use AFTO Form 781 series * 1b - - B

A2.11.5.4. AFTO Form 244-245 - B - -

A2.11.6. Deficiency reporting system A B - -

A2.11.7. Engine and support equipment - B - -

warranty program

A2.11.8. Aircraft configuration/modification - - - -

*A2.12. HAND TOOLS

TR: TO 32-1-101

A2.12.1. Select - B - -

A2.12.2. Use - B - -

*A2.13. Interactive Electronic Technical

Manuals (IETM)
TR: TO 00-5-1, 2J-F110-16-CD-1
and 0-1-CD-1

A2.13.1. TO System - B - -

A2.13.2. Use Interactive Electronic Technical - B - -

Manual

23
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A2.14. GENERAL MAINTENANCE
TR: TOs 1-1A-8, 1-1A-14, 2-1-111,
44B-1-15, and applicable aircraft/
engine TOs

*A2.14.1. Select engine hardware - B - -

*A2.14.2. Use engine hardware - B - -

*A2.14.3. Use hardware safety devices - B - -

*A2.14.4. Bearing handling - B - -

A2.14.5. Perform proper handling of - - - -

Electrostatic Sensitive Discharge
(ESD) Devices

A2.15. ENGINE MAINTENANCE

TR: TOs 00-20-1, 00-35D-54, 1-1A-8,
2J-1-13, 2-1-111, and applicable
aircraft/engine TOs

A2.15.1. Perform preliminary maintenance

procedures

*A2.15.1.1. Work area - B - -

*A2.15.1.2. Support equipment - B - -

*A2.15.1.3. Engine - B - -

A2.15.1.4. Perform maintenance functions - - - -

*A2.15.2. Engine plumbing

A2.15.2.1. Remove - B - -

A2.15.2.2. Inspect - B - -

A2.15.2.3. Install - B - -

A2.16. SPECIAL/MEASURING TOOLS

TR: TOs 32-1-101, 32-1-201, and
applicable engine TOs

*A2.16.1. Select 2b B - -

*A2.16.2. Use 2b B - -

A2.16.3. Use Micrometers/Depth Gauges/Torque * - - - -

Wrenches

A2.17. TEST EQUIPMENT

TR: Applicable engine TOs

A2.17.1. Vibration analyzer - B - -

A2.17.2. Jet Cal Analyzer - B - -

A2.17.3. Vacuum/Pneumatic tester - B - -

*A2.17.4. Use multimeter * 2b B - -

A2.18. SUPPORT EQUIPMENT

TR: TOs 35A4 series, 35D3 series,
35D4 series, and applicable
aircraft/engine TOs

24
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
*A2.18.1. Hoisting equipment

A2.18.1.1. Operate portable 3b - - -

A2.18.1.2. Operate power overhead 1b - - -

A2.18.1.3. Operate transportation equipment 2b B - -

*A2.18.2. Engine maintenance stands

A2.18.2.1. Operate 2b B - -

A2.18.2.2. Remove engine b - - -

A2.18.2.3. Install engine b - - -

A2.18.2.4. Operate personnel stands 1b B - -

A2.18.3. Powered support equipment

A2.18.3.1. Perform inspection - - - -

A2.18.3.2. Operate electrical power units - - - -

(gas turbine/diesel)

A2.18.3.3. Operate air conditioner - - - -

A2.18.3.4. Operate floodlight set - - - -

A2.18.3.5. Operate pneumatic air cart - - - -

A2.19. ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-20 series, 33B4-2-22-1,
33-1-37 series, and applicable
aircraft/engine TOs

A2.19.1. Borescope procedures

*A2.19.1.1. Use Rigid 1b B

A2.19.1.1.1. Hot section - - - -

A2.19.1.1.2. Cold section - - - -

*A2.19.1.2. Use Flexible Borescope A B

A2.19.1.2.1. Hot section - - - -

A2.19.1.2.2. Cold section - - - -

*A2.19.2. Damage analysis - B - B

A2.19.3. Vibration analysis - B - -

A2.19.4. Oil analysis program (OAP) A B - -

A2.19.5. Inspect oil filter/chip detector A B - -

A2.20. ENGINE PRESERVATION

SHIPMENT AND STORAGE
TR: TOs 00-20-4, 00-20-5, 00-85-20,
2J-1-18, 2-1-111, 6J3-1-12, and
applicable engine TOs

*A2.20.1. Prepare engine for shipment b B - -

*A2.20.2. Receiving an engine b B - -

25
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A2.20.3. Engine/module/components in
shipping container

A2.20.3.1. Removal - B - -

A2.20.3.2. Installation - B - -

A2.20.4. Engine/module/components

A2.20.4.1. Preserve * - B - -

A2.20.4.2. Depreserve * - B - -

A2.20.5. Practice corrosion control procedures - - - -

A2.21. JET ENGINE AND RELATED

SYSTEMS
TR: Applicable aircraft/engine TOs

*A2.21.1. Operating principles B B - C

A2.21.2. Constructional features B B

A2.21.2.1. Compressor Fan - B - -

A2.21.2.2. Core - B - -

A2.21.2.3. Combustion - B - -

A2.21.2.4. Turbine - B - -

*A2.21.3. Read and interpret system schematics - B - 2b

*A2.21.4. Engine systems

A2.21.4.1. Electrical A B - -

A2.21.4.2. Oil A B - -

A2.21.4.3. Fuel A B - -

A2.21.4.4. Ignition A B - -

A2.21.4.5. Anti-icing A B - -

A2.21.4.6. Engine start A B - -

A2.21.4.7. Constant speed drive (CSD) A B - -

A2.21.4.8. Integrated drive generator (IDG) A B - -

*A2.21.5. Engine controls

A2.21.5.1. Electronic/mechanical A B - B

A2.21.5.2. Compressor air flow A B - -

A2.21.5.3. Thrust augmentation A B - -

A2.21.5.4. Thrust reverser A B - -

A2.21.5.5 Engine monitoring system trend data A B - B

A2.22. ENGINE RIGGING

TR: Applicable aircraft/engine TOs

*A2.22.1. Rig * A B - -

A2.22.2. Inspect * - B - -

26
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
*A2.23. ENGINE REMOVAL AND
INSTALLATION IN AIRFRAME
TR: TOs 1-1A-8, 2J-1-24, and
applicable aircraft TOs

A2.23.1. Remove engine 2b B - -

A2.23.2. Install engine 2b B - -

A2.23.3. Service engine a B - -

A2.24. AIRCRAFT INSTALLED ENGINE

TESTING
TR: Applicable aircraft/engine TOs

A2.24.1. Perform operational checks with or

without noise suppressors

A2.24.1.1. Engine operation - B - -

A2.24.1.2. Perform ground observer/fireguard - - - -

duties/fire control panel

A2.24.1.3. Engine trim - B - -

*A2.24.1.4. Evaluate engine performance - - - -

A2.24.1.5. System and component troubleshooting - - - -

A2.24.1.6. Aircraft restraining devices

A2.24.1.6.1. Removal - - - -

A2.24.1.6.2. Inspection - - - -

A2.24.1.6.3. Installation - - - -

A2.24.1.7. Fan Trim Balance - - - -

A2.24.1.8. Noise suppressor/hush house - B - -

A2.24.1.9. Related systems

A2.24.1.9.1. Operate flaps/slats system with slats - - - -

disabled

A2.24.1.9.2. Operate auxiliary hydraulic system - - - -

A2.24.1.9.3. Operate mission computer - - - -

A2.24.1.9.4. Check/service engine fuel control - - - -

A2.24.1.9.5. Operate Constant Speed Drive (CSD)/ - - - -

Integrated Drive Generator (IDG)

A2.24.1.9.6. Electronic engine control operational - - - -

checkout (static check)

A2.24.1.9.7. Operate engine bleed control system - - - -

A2.24.1.9.8. Operate mission computer - - - -

A2.25. TEST STAND ENGINE TESTING

TR: TOs 00-20-1, 00-25-238, and
applicable engine TOs

A2.25.1. Engine testing - B - -

27
Attachment 2
 SPECIALTY TRAINING STANDARD
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A2.25.2. Pre-operational checks in test stand - B - -

A2.25.3. Operational checks of engine test stand - B - -

A2.25.4. Engine performance - B - B

A2.25.5. Engine system components adjustment - B - -

A2.25.6. Post-operational checks in test stand - B - -

A2.25.7. System and component troubleshooting - B - -

A2.25.8. Test stand operation and maintenance - B - -

A2.25.9. Remove/install engine on test stand - - - -

A2.25.10. Perform ground observer/fireguard - - - -

duties/fire control panel

*A2.26. SMALL GAS TURBINE ENGINE A B - -

AND AUXILIARY POWER UNIT
(APU) OPERATING PRINCIPLES
TR: Applicable engine TOs
A2.27. GENERAL MAINTENANCE/
PRODUCTION TEAM
MAINTENANCE TASKS
TR: Applicable aircraft & engine TOs
A2.27.1. Technical order familiarization - - - -
A2.27.2. Flightline safety/precautions/security - - - -
A2.27.3. Introduction to aircraft/airframe - - - -
familiarization/egress
A2.27.4. Inspect/use ground maintenance stands - - - -
A2.27.5. Defensive Systems (DS) familiarization - - - -
(on applicable aircraft)
A2.27.6. Statically ground aircraft - - - -
A2.27.7. Apply/disconnect external electrical - - - -
power unit
A2.27.8. Perform jacking team member - - - -
A2.27.9. Perform refuel/defuel team member - - - -
duties
A2.27.10. Remove/install aircraft maintenance - - - -
access panels
A2.27.11. Use aircraft interphone system - - - -
A2.27.12. Perform aircraft marshaling procedures - - - -
A2.27.13. Tow aircraft - - - -
A2.27.14. Perform wing/tail walker duties - - - -
A2.27.15. Brake Operator - - - -
A2.27.16. General Maintenance/Production - - - -
Team Maintenance Tasks
A2.27.17. Technical order familiarization - - - -

28
Attachment 2
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
ATTACHMENT 3
NOTE 1: The tasks and knowledge listed in this attachment are performed by personnel in the apprentice (3-level) J3ABR2A631D 007 (F100)
and J3ABR2A631E 006 (F110) courses. The tasks and proficiency codes listed in column 4A of this attachment are driven by unique
equipment design and because the F100 and F110 3-level courses are Mission Ready Airmen (MRA) courses.

NOTE 2: Due to unique engine design of tasks A3.4.2.16.2., A3.4.2.17.1., and A3.4.2.17.3. (core compressor inspection and repair), personnel in the
apprentice F100 course will not complete these tasks.
NOTE 3: Tasks and knowledge identified by an asterisk (*) in column 1 are trained in the resident wartime courses.
NOTE 4: Tasks A3.2., A3.2.1., and A3.2.2. will only be completed by the F110 course.
NOTE 5: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on F100, F101, F110, F-118, F119, F404,
and J85 engines.
*A3.1. HANDTOOLS
TR: TO 32-1-101

A3.1.1. Select * 2b - - -

A3.1.2. Use * 3c - - -

A3.2 Interactive Electronic Technical

Manuals (IETM)
TR: TO 00-5-1, 2J-F110-16-CD-1
and 0-1-CD-1

A3.2.1. TO System B - - -

A3.2.2. Use Interactive Electronic Technical 2b/- - - -

Manual

A3.3. GENERAL MAINTENANCE

TR: TOs 1-1A-8, 1-1A-14, 2-1-111,
44B-1-15, and applicable
aircraft/engine TOs

*A3.3.1. Select engine hardware * 3c - - -

*A3.3.2. Use engine hardware * 3c - - -

*A3.3.3. Use hardware safety devices * 3c - - -

*A3.3.4. Bearing handling B - - -

A3.3.5. Perform proper handling of - - - -

Electro-static Sensitive Discharge
(ESD) Devices

A3.4. ENGINE MAINTENANCE

TR: TOs 00-20-1, 00-35D-54, 1-1A-8,
2J-1-13, 2-1-111, and applicable
aircraft/engine TOs

*A3.4.1. Perform preliminary maintenance

procedures

A3.4.1.1. Work area * 2b - - -

A3.4.1.2. Support equipment * 2b - - -

A3.4.1.3. Engine * 2b - - -

29
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.2. Perform maintenance functions

*A3.4.2.1. Engine plumbing

A3.4.2.1.1. Remove 3b - - -

A3.4.2.1.2. Inspect * 1b - - -

A3.4.2.1.3. Install * 3b - - -

A3.4.2.2. Engine accessories

*A3.4.2.2.1. Exciter

A3.4.2.2.1.1. Remove 3c - - -

A3.4.2.2.1.2. Inspect * 1b - - -

A3.4.2.2.1.3. Install * 3c - - -

*A3.4.2.2.2. Fuel pump

A3.4.2.2.2.1. Remove 3c - - -

A3.4.2.2.2.2. Inspect * 1b - - -

A3.4.2.2.2.3. Install 3c - - -

*A3.4.2.2.3. Anti-ice

A3.4.2.2.3.1. Remove 3c - - -

A3.4.2.2.3.2. Inspect * 1b - - -

A3.4.2.2.3.3. Install * 3c - - -

*A3.4.2.2.4. Igniter

A3.4.2.2.4.1. Remove 3c - - -

A3.4.2.2.4.2. Inspect * 1b - - -

A3.4.2.2.4.3. Install * 3c - - -

*A3.4.2.2.5. Fuel control

A3.4.2.2.5.1. Remove 3c - - -

A3.4.2.2.5.2. Inspect * 1b - - -

A3.4.2.2.5.3. Install * 3c - - -

A3.4.2.2.6. Fuel Filter

A3.4.2.2.6.1. Remove - - - -

A3.4.2.2.6.2. Inspect - - - -

A3.4.2.2.6.3. Install - - - -

A3.4.2.2.7. Fuel Filter Differential Pressure

Indicator

A3.4.2.2.7.1. Remove - - - -

A3.4.2.2.7.2. Inspect - - - -

30
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.2.2.7.3. Install - - - -

A3.4.2.2.8. Oil Pump

A3.4.2.2.8.1. Remove - - - -

A3.4.2.2.8.2. Inspect - - - -

A3.4.2.2.8.3. Install - - - -

A3.4.2.2.9. Oil Tank

*A3.4.2.2.9.1. Remove 2b - - -

A3.4.2.2.9.2. Inspect - - - -

*A3.4.2.2.9.3. Install 2b - - -

*A3.4.2.2.9.4. Service - - - -

A3.4.2.2.10. Oil Pressure Transmitter

*A3.4.2.2.10.1. Remove 2b - - -

A3.4.2.2.10.2. Inspect - - - -

*A3.4.2.2.10.3. Install * 2b - - -

A3.4.2.2.11. Oil Cooler

A3.4.2.2.11.1. Remove - - - -

A3.4.2.2.11.2. Inspect - - - -

A3.4.2.2.11.3. Install - - - -

A3.4.2.2.12. Hydraulic Pump

A3.4.2.2.12.1. Remove - - - -

A3.4.2.2.12.2. Inspect - - - -

A3.4.2.2.12.3. Install - - - -

A3.4.2.2.13. Oil Filter/Strainer

A3.4.2.2.13.1. Remove - - - -

A3.4.2.2.13.2. Inspect * - - - -

A3.4.2.2.13.3. Install - - - -

A3.4.2.2.14. Chip detector

A3.4.2.2.14.1. Remove - - - -

A3.4.2.2.14.2. Inspect * - - - -

A3.4.2.2.14.3. Install - - - -

A3.4.2.2.15. Lube Filter Differential Pressure

Indicator

A3.4.2.2.15.1. Remove - - - -

A3.4.2.2.15.2. Inspect - - - -

31
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.2.2.15.3. Install - - - -

A3.4.2.2.16. Lube Flow Sensor

A3.4.2.2.16.1. Remove - - - -

A3.4.2.2.16.2. Inspect - - - -

A3.4.2.2.16.3. Install - - - -

A3.4.2.2.17. Breather Pressurizing Valve

A3.4.2.2.17.1. Remove - - - -

A3.4.2.2.17.2. Inspect - - - -

A3.4.2.2.17.3. Install - - - -

A3.4.2.2.18. AC Generator

A3.4.2.2.18.1. Remove - - - -

A3.4.2.2.18.2. Inspect - - - -

A3.4.2.2.18.3. Install - - - -

A3.4.2.2.19. Engine Electronic Control

(EEC, DEC, DEEC, EFT & AFTC)

*A3.4.2.2.19.1. Remove 2b - - -

A3.4.2.2.19.2. Inspect - - - -

*A3.4.2.2.19.3. Install 2b - - -

A3.4.2.2.20. Inlet/Variable Stator Vane Actuating

System

A3.4.2.2.20.1. Remove - - - -

A3.4.2.2.20.2. Inspect - - - -

A3.4.2.2.20.3. Install - - - -

A3.4.2.2.21. Turbine Temperature Indicating

System (FTIT, Pyrometer)

A3.4.2.2.21.1. Remove - - - -

A3.4.2.2.21.2. Inspect - - - -

A3.4.2.2.21.3. Install - - - -

*A3.4.3. Gearbox

A3.4.3.1. Remove 3b - - -

A3.4.3.2. Inspect * 1b - - -

A3.4.3.3. Install * 3b - - -

* A3.4.4. Compressor (Fan)

A3.4.4.1. Remove 2b - - -

A3.4.4.2. Inspect * 1b - - -

32
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.4.3. Install 2b - - -

A3.4.5. Blades

A3.4.5.1. Remove - - - -

A3.4.5.2. Inspect - - - -

A3.4.5.3. Install - - - -

*A3.4.5.4. Repair (Blend) a - - -

A3.4.6. Fan Frame Assembly

A3.4.6.1. Remove - - - -

A3.4.6.2. Inspect - - - -

A3.4.6.3. Install - - - -

A3.4.6.4. Repair - - - -

A3.4.7. Fan Stator Case

A3.4.7.1. Remove - - - -

A3.4.7.2. Inspect - - - -

A3.4.7.3. Install - - - -

A3.4.8. Fan Duct

A3.4.8.1. Remove - - - -

A3.4.8.2. Inspect - - - -

A3.4.8.3. Install - - - -

A3.4.9. Augmenter

*A3.4.9.1. Augmenter/Exhaust Nozzle Assembly

A3.4.9.1.1. Remove 3c - - -

A3.4.9.1.2. Inspect * 1b - - -

A3.4.9.1.3. Install 3c - - -

A3.4.9.2. Spray-bar/Spray-ring

A3.4.9.2.1. Remove - - - -

A3.4.9.2.2. Inspect - - - -

A3.4.9.2.3 Install - - - -

A3.4.9.3. Fuel Control

A3.4.9.3.1. Remove - - - -

A3.4.9.3.2. Inspect - - - -

A3.4.9.3.3. Install - - - -

A3.4.9.4. Fuel Pump

A3.4.9.4.1. Remove - - - -

33
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.9.4.2. Inspect - - - -

A3.4.9.4.3. Install - - - -

A3.4.9.5 F100 Fuel Pump Controller

A3.4.9.5.1. Remove - - - -

A3.4.9.5.2. Inspect - - - -

A3.4.9.5.3. Install - - - -

A3.4.9.6. Nozzle Actuator

A3.4.9.6.1. Remove - - - -

A3.4.9.6.2. Inspect - - - -

A3.4.9.6.3. Install - - - -

A3.4.9.7. F100 Convergent Exhaust Nozzle

Control (CENC)

A3.4.9.7.1. Remove - - - -

A3.4.9.7.2. Inspect - - - -

A3.4.9.7.3. Install - - - -

A3.4.9.8. Liner/Duct

A3.4.9.8.1. Remove - - - -

A3.4.9.8.2. Inspect - - - -

A3.4.9.8.3. Install - - - -

A3.4.9.9. Flame holder

A3.4.9.9.1. Remove - - - -

A3.4.9.9.2. Inspect - - - -

A3.4.9.9.3. Install - - - -

A3.4.9.10. Igniter

A3.4.9.10.1. Remove - - - -

A3.4.9.10.2. Inspect - - - -

A3.4.9.10.3. Install - - - -

A3.4.9.11. Flame Sensor/Light-off Detector

A3.4.9.11.1. Remove - - - -

A3.4.9.11.2. Inspect - - - -

A3.4.9.11.3. Install - - - -

A3.4.9.12. Nozzle Position Transmitter

A3.4.9.12.1. Remove - - - -

A3.4.9.12.2. Inspect - - - -

34
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.9.12.3. Install - - - -

*A3.4.9.13. Flap/seals/segment

A3.4.9.13.1. Remove 3b - - -

A3.4.9.13.2. Inspect 1b - - -

A3.4.9.13.3. Install 3b - - -

A3.4.10. Turbine section

*A3.4.10.1. Low Pressure Turbine (FDTM)

A3.4.10.1.1. Remove 3b - - -

A3.4.10.1.2. Inspect 1b - - -

A3.4.10.1.3. Install 3b - - -

*A3.4.10.2. High Pressure Turbine

A3.4.10.2.1. Remove 2b - - -

A3.4.10.2.2. Inspect 1b - - -

A3.4.10.2.3. Install 2b - - -

A3.4.10.3. Blades/Nozzle Vanes & Segments

A3.4.10.3.1. Remove - - - -

A3.4.10.3.2. Inspect - - - -

A3.4.10.3.3. Install - - - -

A3.4.10.4. Shroud Segments/Blade Outer Air

Seal (BOAS)

A3.4.10.4.1. Remove - - - -

A3.4.10.4.2. Inspect - - - -

A3.4.10.4.3. Install - - - -

*A3.4.11. Combustion section

A3.4.11.1. Remove 2b - - -

A3.4.11.2. Inspect 1b - - -

A3.4.11.3. Install 2b - - -

A3.4.12. Diffuser Case/Combustor Diffuser

Nozzle

A3.4.12.1. Remove - - - -

A3.4.12.2. Inspect - - - -

A3.4.12.3. Install - - - -

A3.4.13. Engine bearings

* A3.4.13.1. Remove 2b - - -

35
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.13.2. Clean - - - -

A3.4.13.3. Inspect - - - -

* A3.4.13.4. Install 2b - - -

*A3.4.14. Fuel manifolds

A3.4.14.1. Remove 2b - - -

A3.4.14.2. Inspect 1b - - -

A3.4.14.3. Install 2b - - -

*A3.4.15. Fuel nozzles

A3.4.15.1. Remove 2b - - -

A3.4.15.2. Inspect 1b - - -

A3.4.15.3. Install 2b - - -

A3.4.16. Compressor (Core)

A3.4.16.1. Remove - - - -

* A3.4.16.2. Inspect 1b - - -

A3.4.16.3. Install - - - -

A3.4.17. Blades

* A3.4.17.1. Remove 1b - - -

A3.4.17.2. Inspect - - - -

* A3.4.17.3. Install 1b - - -

A3.4.17.4. Repair (Blend) - - - -

A3.4.18. Compressor Stator Case

A3.4.18.1. Remove - - - -

* A3.4.18.2. Inspect - - - -

A3.4.18.3. Install - - - -

A3.4.19. Thrust Control Actuator

A3.4.19.1. Remove - - - -

A3.4.19.2. Inspect - - - -

A3.4.19.3. Install - - - -

A3.4.19.4. Rig - - - -

A3.4.20. Fuel Flow Meter

A3.4.20.1. Remove - - - -

A3.4.20.2. Install - - - -

A3.4.21 Main Fuel Filter Assembly and Element

A3.4.21.1. Remove - - - -

36
Attachment 3
 F100 and F110
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A3.4.21.2. Inspect - - - -

A3.4.21.3. Install - - - -

A3.4.21.4. Repair - - - -

A3.4.22. Front Compressor Stator

A3.4.22.1. Remove - - - -

A3.4.22.2. Inspect - - - -

A3.4.22.3. Install - - - -

A3.4.23. Central Integrated Test System

(CITS) Processor/Engine Diagnostic
Unit (EDU)/Engine Monitoring
System Processor (EMSP)
TR: Applicable engine TOs

A3.4.23.1. Remove - - - -

A3.4.23.2. Inspect - - - -

A3.4.23.3. Install - - - -

A3.4.24. Fan Speed Sensor/N1 Speed

Indicating System

A3.4.24.1. Remove - - - -

A3.4.24.2. Inspect - - - -

A3.4.24.3. Install - - - -

A3.4.25. Accelerometers

A3.4.25.1. Remove - - - -

A3.4.25.2. Install - - - -

37
Attachment 3
38
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
ATTACHMENT 4
NOTE 1: The tasks and knowledge listed in this attachment are performed by personnel in the apprentice (3-level) J3ABR2A631C 002
(TF33, TF34, F108) course.

NOTE 2: Line items A4.1.2.,A4.3.2.2.3.1., A4.3.2.3.34.1., A4.3.2.3..34.3., A4.3.2.3.35.1., and A4.3.2.3.35.3., are MRA tasks
NOTE 3: Tasks and knowledge identified by an asterisk * in column 1 are trained in the resident wartime courses.
NOTE 4: Those tasks identified by either 3c/2b, 3b/2b or 2b/- are constrained by manpower costs and will be added as manpower becomes available
NOTE 5: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on F-108, JT3D, TF33 (Except C-141), TF34,
and PW 2020 engines
*A4.1. HANDTOOLS
TR: TO 32-1-101

A4.1.1. Select * 2b - - -

A4.1.2. Use * 3c - - -

A4.2. GENERAL MAINTENANCE

TR: TOs 1-1A-8, 1-1A-14, 2-1-111,
44B-1-15, and applicable
aircraft/engine TOs

*A4.2.1. Select engine hardware * 2b - - -

*A4.2.2. Use engine hardware * 2b - - -

*A4.2.3. Use hardware safety devices * 2b - - -

*A4.2.4. Bearing handling B - - -

A4.2.5. Perform proper handling of Electrostatic - - - -

Sensitive Devices (ESD)

A4.2.6. Open/Close engine cowling - - - -

A4.2.7. Engine O-Ring/Garlock Seals - - - -

A4.3. ENGINE MAINTENANCE

TR: TOs 00-20-1, 00-35D-54,
1-1A-8, 2J-1-13, 2-1-111, and
applicable aircraft/engine TOs

*A4.3.1. Perform preliminary maintenance

procedures

A4.3.1.1. Work area * 2b - - -

A4.3.1.2. Support equipment * 2b - - -

A4.3.1.3. Engine * 2b - - -

A4.3.2. Perform maintenance functions

*A4.3.2.1. Engine plumbing

A4.3.2.1.1. Remove 3b - - -

A4.3.2.1.2. Inspect * 1b - - -

A4.3.2.1.3. Install * 3b - - -

A4.3.2.2. Engine accessories

39
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.2.1. Engine Anti-ice Valve

A4.3.2.2.1.1. Remove - - - -

A4.3.2.2.1.2. Inspect - - - -

A4.3.2.2.1.3. Install - - - -

A4.3.2.2.2. Fuel pump

*A4.3.2.2.2.1. Remove 3b/2b - - -

A4.3.2.2.2.2. Inspect - - - -

*A4.3.2.2.2.3. Install 3b/2b - - -

*A4.3.2.2.3. Fuel control/Main Engine Control

A4.3.2.2.3.1. Remove (TF34) * 3c/2b - - -

A4.3.2.2.3.2. Inspect * 1b - - -

A4.3.2.2.3.3. Install (TF34) * 3c/2b - - -

A4.3.2.2.4. Fuel Oil Cooler

A4.3.2.2.4.1. Remove - - - -

A4.3.2.2.4.2. Inspect - - - -

A4.3.2.2.4.3. Install - - - -

A4.3.2.2.5. Servo Fuel Heater

A4.3.2.2.5.1. Remove - - - -

A4.3.2.2.5.2. Inspect - - - -

A4.3.2.2.5.3. Install - - - -

A4.3.2.2.6. Fuel Filter

A4.3.2.2.6.1. Remove - - - -

A4.3.2.2.6.2. Inspect * - - - -

A4.3.2.2.6.3. Install - - - -

A4.3.2.2.7. Fuel Manifold

A4.3.2.2.7.1. Remove - - - -

A4.3.2.2.7.2. Inspect - - - -

A4.3.2.2.7.3. Install - - - -

*A4.3.2.2.8. Fuel Nozzles (External)

A4.3.2.2.8.1. Remove (TF34) 3c/2b - - -

A4.3.2.2.8.2. Inspect 1b - - -

A4.3.2.2.8.3. Install (TF34) 3c/2b - - -

A4.3.2.2.9. Fuel Distributor

A4.3.2.2.9.1. Remove - - - -

40
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.2.9.2. Inspect - - - -

A4.3.2.2.9.3. Install - - - -

A4.3.2.2.10. Pressurizing and Dump Valve (P&D)

A4.3.2.2.10.1. Remove - - - -

A4.3.2.2.10.2. Inspect - - - -

A4.3.2.2.10.3. Install - - - -

A4.3.2.2.11. Exciter

*A4.3.2.2.11.1. Remove (TF34) 2b - - -

A4.3.2.2.11.2. Inspect - - - -

*A4.3.2.2.11.3. Install (TF34) 2b - - -

*A4.3.2.2.12. Igniter Plug

A4.3.2.2.12.1. Remove (TF34) 3c/2b - - -

A4.3.2.2.12.2. Inspect 1b - - -

A4.3.2.2.12.3. Install (TF34) * 3c/2b - - -

A4.3.2.2.13. Igniter Lead

A4.3.2.2.13.1. Remove - - - -

A4.3.2.2.13.2. Inspect - - - -

A4.3.2.2.13.3. Install - - - -

A4.3.2.2.14. Thermocouple Harness

A4.3.2.2.14.1. Remove - - - -

A4.3.2.2.14.2. Inspect - - - -

A4.3.2.2.14.3. Install - - - -

A4.3.2.2.15. Thermocouples

A4.3.2.2.15.1. Remove - - - -

A4.3.2.2.15.2. Inspect - - - -

A4.3.2.2.15.3. Install - - - -

A4.3.2.2.16. Engine Temperature Amplifier (T5)

A4.3.2.2.16.1. Remove - - - -

A4.3.2.2.16.2. Inspect - - - -

A4.3.2.2.16.3. Install * - - - -

A4.3.2.2.17. Compressor Bleed Valve

A4.3.2.2.17.1. Remove - - - -

A4.3.2.2.17.2. Inspect - - - -

A4.3.2.2.17.3. Install - - - -

41
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.2.18. Compressor Bleed Valve Actuator

A4.3.2.2.18.1. Remove - - - -

A4.3.2.2.18.2. Inspect - - - -

A4.3.2.2.18.3. Install - - - -

A4.3.2.2.19. Compressor Bleed Valve Governor

A4.3.2.2.19.1. Remove - - - -

A4.3.2.2.19.2. Inspect - - - -

A4.3.2.2.19.3. Install - - - -

A4.3.2.2.20. Compressor Bleed Reset Valve

A4.3.2.2.20.1. Remove - - - -

A4.3.2.2.20.2. Inspect - - - -

A4.3.2.2.20.3. Install - - - -

A4.3.2.2.21. Compressor Bleed Valve Accumulator

A4.3.2.2.21.1. Remove - - - -

A4.3.2.2.21.2. Inspect - - - -

A4.3.2.2.21.3. Install - - - -

A4.3.2.2.22. Oil Pump

*A4.3.2.2.22.1. Remove 2b - - -

A4.3.2.2.22.2. Inspect - - - -

*A4.3.2.2.22.3. Install 2b - - -

A4.3.2.2.23. Oil Tank

A4.3.2.2.23.1. Remove - - - -

A4.3.2.2.23.2. Inspect - - - -

A4.3.2.2.23.3. Install - - - -

*A4.3.2.2.23.4. Service a - - -

A4.3.2.2.24. Oil Pressure Relief Valve

A4.3.2.2.24.1. Remove - - - -

A4.3.2.2.24.2. Inspect - - - -

A4.3.2.2.24.3. Install - - - -

A4.3.2.2.24.4. Adjust - - - -

A4.3.2.2.25. Oil Breather Pressurizing Valve

A4.3.2.2.25.1. Remove - - - -

A4.3.2.2.25.2. Inspect - - - -

A4.3.2.2.25.3. Install - - - -

42
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.2.26. Oil Filter/Screens

A4.3.2.2.26.1. Remove - - - -

A4.3.2.2.26.2. Inspect * - - - -

A4.3.2.2.26.3. Install - - - -

A4.3.2.2.27. Chip Detectors

A4.3.2.2.27.1. Remove - - - -

A4.3.2.2.27.2. Inspect * - - - -

A4.3.2.2.27.3. Install - - - -

A4.3.2.2.28. A Sump Scavenge Pump

A4.3.2.2.28.1. Remove - - - -

A4.3.2.2.28.2. Inspect - - - -

A4.3.2.2.28.3. Install - - - -

A4.3.2.2.29. Sump Accumulator

A4.3.2.2.29.1. Remove - - - -

A4.3.2.2.29.2. Inspect - - - -

A4.3.2.2.29.3. Install - - - -

A4.3.2.3. QUICK ENGINE CHANGE (QEC)

ACCESSORIES
TR: Applicable Aircraft/Engine TOs

A4.3.2.3.1. Tachometer Generator

A4.3.2.3.1.1. Remove - - - -

A4.3.2.3.1.2. Inspect - - - -

A4.3.2.3.1.3. Install - - - -

A4.3.2.3.2. Fuel Flow Transmitter

A4.3.2.3.2.1. Remove - - - -

A4.3.2.3.2.2. Inspect - - - -

A4.3.2.3.2.3. Install - - - -

A4.3.2.3.3. Low Oil Pressure Switch

A4.3.2.3.3.1. Remove - - - -

A4.3.2.3.3.2. Inspect - - - -

A4.3.2.3.3.3. Install - - - -

A4.3.2.3.4. Oil Pressure Transmitter

A4.3.2.3.4.1. Remove - - - -

A4.3.2.3.4.2. Inspect - - - -

43
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.3.4.3. Install - - - -

A4.3.2.3.5. Oil Differential Pressure Switch

A4.3.2.3.5.1. Remove - - - -

A4.3.2.3.5.2. Inspect - - - -

A4.3.2.3.5.3. Install - - - -

A4.3.2.3.6. Oil Temperature Sensor

A4.3.2.3.6.1. Remove - - - -

A4.3.2.3.6.2. Inspect - - - -

A4.3.2.3.6.3. Install - - - -

A4.3.2.3.7. Engine Air Oil Cooler

A4.3.2.3.7.1. Remove - - - -

A4.3.2.3.7.2. Inspect - - - -

A4.3.2.3.7.3. Install - - - -

A4.3.2.3.8. Low Oil Quantity Switch

A4.3.2.3.8.1. Remove - - - -

A4.3.2.3.8.2. Inspect - - - -

A4.3.2.3.8.3. Install - - - -

A4.3.2.3.9. Constant Speed Drive (CSD)

A4.3.2.3.9.1. Remove - - - -

A4.3.2.3.9.2. Inspect - - - -

A4.3.2.3.9.3. Install - - - -

A4.3.2.3.10. Generator

A4.3.2.3.10.1. Remove - - - -

A4.3.2.3.10.2. Inspect - - - -

A4.3.2.3.10.3. Install - - - -

A4.3.2.3.11. Integrated Drive Generator (IDG)

*A4.3.2.3.11.1. Remove 2b - - -

A4.3.2.3.11.2. Inspect - - - -

*A4.3.2.3.11.3. Install 2b - - -

A4.3.2.3.11.4. Service - - - -

A4.3.2.3.12. Filters

A4.3.2.3.12.1. Remove - - - -

A4.3.2.3.12.2. Inspect - - - -

A4.3.2.3.12.3. Install - - - -

44
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.3.13. CSD Oil Tank

A4.3.2.3.13.1. Remove - - - -

A4.3.2.3.13.2. Inspect - - - -

A4.3.2.3.13.3. Install - - - -

A4.3.2.3.13.4. Service - - - -

A4.3.2.3.14. CSD/IDG Oil Cooler

A4.3.2.3.14.1. Remove - - - -

A4.3.2.3.14.2. Inspect - - - -

A4.3.2.3.14.3. Install - - - -

*A4.3.2.3.15. Engine Starter

A4.3.2.3.15.1. Remove (TF34) 3c/2b - - -

A4.3.2.3.15.2. Inspect 1b - - -

A4.3.2.3.15.3. Install (TF34) * 3c/2b - - -

A4.3.2.3.15.4. Service * a - - -

*A4.3.2.3.16. Starter Control Valve

A4.3.2.3.16.1. Remove (TF34) 3c/2b - - -

A4.3.2.3.16.2. Inspect 1b - - -

A4.3.2.3.16.3. Install (TF34) * 3c/2b - - -

A4.3.2.3.17. Bleed Air Shutoff Valve (TF34)

A4.3.2.3.17.1. Remove - - - -

A4.3.2.3.17.2. Inspect - - - -

A4.3.2.3.17.3. Install - - - -

A4.3.2.3.18. Hydraulic Pumps

A4.3.2.3.18.1. Remove - - - -

A4.3.2.3.18.2. Inspect - - - -

A4.3.2.3.18.3. Install - - - -

A4.3.2.3.19. Hydraulic Oil Cooler

A4.3.2.3.19.1. Remove - - - -

A4.3.2.3.19.2. Inspect - - - -

A4.3.2.3.19.3. Install - - - -

A4.3.2.3.20. Engine Mounted Hydraulic Filter

A4.3.2.3.20.1. Remove - - - -

A4.3.2.3.20.2. Inspect - - - -

A4.3.2.3.20.3. Install - - - -

45
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.3.21. Engine Harness

A4.3.2.3.21.1. Remove - - - -

A4.3.2.3.21.2. Inspect - - - -

A4.3.2.3.21.3. Install - - - -

A4.3.2.3.22. Fire Loop

A4.3.2.3.22.1. Remove - - - -

A4.3.2.3.22.2. Inspect - - - -

A4.3.2.3.22.3. Install - - - -

A4.3.2.3.23. Tail pipe/Tail cone

A4.3.2.3.23.1. Remove - - - -

A4.3.2.3.23.2. Inspect - - - -

A4.3.2.3.23.3. Install - - - -

A4.3.2.3.24. Engine Throttle Linkage/Box

A4.3.2.3.24.1. Remove - - - -

A4.3.2.3.24.2. Inspect - - - -

A4.3.2.3.24.3. Install - - - -

A4.3.2.3.24.4. Rig - - - -

A4.3.2.3.25. Fan Exit Fairing

A4.3.2.3.25.1. Remove - - - -

A4.3.2.3.25.2. Inspect - - - -

A4.3.2.3.25.3. Install - - - -

A4.3.2.3.26. Engine Pylon (TF34)

A4.3.2.3.26.1. Remove - - - -

A4.3.2.3.26.2. Inspect - - - -

A4.3.2.3.26.3. Install - - - -

A4.3.2.3.27. Ring Cowl

A4.3.2.3.27.1. Remove - - - -

A4.3.2.3.27.2. Inspect - - - -

A4.3.2.3.27.3. Install - - - -

A4.3.2.3.28. Nacelle Anti-ice Valve

A4.3.2.3.28.1. Remove - - - -

A4.3.2.3.28.2. Inspect - - - -

A4.3.2.3.28.3. Install - - - -

A4.3.2.3.29. Engine Mounts

46
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.3.29.1. Remove - - - -

A4.3.2.3.29.2. Inspect - - - -

A4.3.2.3.29.3. Install - - - -

A4.3.2.3.30. Nose Dome/Spinner Cone

A4.3.2.3.30.1. Remove - - - -

A4.3.2.3.30.2. Inspect - - - -

A4.3.2.3.30.3. Install - - - -

A4.3.2.3.31. Vibration Accelerometer (TF34)

A4.3.2.3.31.1. Remove - - - -

A4.3.2.3.31.2. Inspect - - - -

A4.3.2.3.31.3. Install - - - -

*A4.3.2.3.32. Gearbox

A4.3.2.3.32.1. Remove 2b/- - - -

A4.3.2.3.32.2. Inspect 1b/- - - -

A4.3.2.3.32.3. Install 2b/- - - -

A4.3.2.3.33. Power Take Off (PTO) Assembly

A4.3.2.3.33.1. Remove - - - -

A4.3.2.3.33.2. Inspect - - - -

A4.3.2.3.33.3. Install - - - -

*A4.3.2.3.34. Fan Disk (Compressor)

A4.3.2.3.34.1. Remove 3c - - -

A4.3.2.3.34.2. Inspect * 1b - - -

A4.3.2.3.34.3. Install 3c - - -

A4.3.2.3.35. Blades

A4.3.2.3.35.1. Remove 3c - - -

A4.3.2.3.35.2. Inspect * 1b - - -

A4.3.2.3.35.3. Install 3c - - -

*A4.3.2.3.35.4. Repair (Blend) a - - -

A4.3.2.3.36. Fan Case/Stator Case

A4.3.2.3.36.1. Remove - - - -

A4.3.2.3.36.2. Inspect - - - -

A4.3.2.3.36.3. Install - - - -

A4.3.2.3.37. Inlet Guide Vane (IGV) Case

A4.3.2.3.37.1. Remove - - - -

47
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.3.37.2. Inspect - - - -

A4.3.2.3.37.3. Install - - - -

A4.3.2.3.38. Bearing/Carbon Seal/Sump Area

A4.3.2.3.38.1. Remove - - - -

A4.3.2.3.38.2. Inspect - - - -

A4.3.2.3.38.3. Install - - - -

A4.3.2.3.39. Compressor (Core)

A4.3.2.3.39.1. Remove - - - -

A4.3.2.3.39.2. Inspect - - - -

A4.3.2.3.39.3. Install - - - -

A4.3.2.3.40. Blade

A4.3.2.3.40.1. Remove - - - -

A4.3.2.3.40.2. Inspect - - - -

A4.3.2.3.40.3. Install - - - -

A4.3.2.3.40.4. Repair - - - -

A4.3.2.3.41. Front Stator Case

A4.3.2.3.41.1. Remove - - - -

A4.3.2.3.41.2. Inspect - - - -

A4.3.2.3.41.3. Install - - - -

A4.3.2.3.41.4. Repair - - - -

A4.3.2.3.42. Rear Stator Case

A4.3.2.3.42.1. Remove - - - -

A4.3.2.3.42.2. Inspect - - - -

A4.3.2.3.42.3. Install - - - -

A4.3.2.3.42.4. Repair - - - -

A4.3.2.3.43. Variable Guide Vanes

A4.3.2.3.43.1. Remove - - - -

A4.3.2.3.43.2. Inspect - - - -

A4.3.2.3.43.3. Install - - - -

A4.3.2.3.43.4. Rig - - - -

A4.3.2.3.44. Actuator

A4.3.2.3.44.1. Remove - - - -

A4.3.2.3.44.2. Inspect - - - -

A4.3.2.3.44.3. Install - - - -

48
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.3.44.4. Rig - - - -

A4.3.2.3.45. Feedback Cable

A4.3.2.3.45.1. Remove - - - -

A4.3.2.3.45.2. Inspect - - - -

A4.3.2.3.45.3. Install - - - -

A4.3.2.3.45.4. Rig - - - -

A4.3.2.3.46. Compressor Inlet Temperature (CIT)

Sensor

A4.3.2.3.46.1. Remove - - - -

A4.3.2.3.46.2. Inspect - - - -

A4.3.2.3.46.3. Install - - - -

A4.3.2.4. COMBUSTION SECTION

A4.3.2.4.1. Combustion Casing

A4.3.2.4.1.1. Remove - - - -

A4.3.2.4.1.2. Inspect - - - -

A4.3.2.4.1.3. Install - - - -

A4.3.2.4.2. Combustion Liner

A4.3.2.4.2.1. Remove - - - -

A4.3.2.4.2.2. Inspect - - - -

A4.3.2.4.2.3. Install - - - -

A4.3.2.4.3. B Sump Assembly

A4.3.2.4.3.1. Remove - - - -

A4.3.2.4.3.2. Inspect - - - -

A4.3.2.4.3.3. Install - - - -

A4.3.2.4.4. Mount Ring

A4.3.2.4.4.1. Remove - - - -

A4.3.2.4.4.2. Inspect - - - -

A4.3.2.4.4.3. Install - - - -

A4.3.2.5. TURBINE SECTION

A4.3.2.5.1. High Pressure Turbine

A4.3.2.5.1.1. Rotor Assembly

A4.3.2.5.1.1.1. Remove - - - -

A4.3.2.5.1.1.2. Inspect - - - -

A4.3.2.5.1.1.3. Install - - - -

49
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.5.1.2. Nozzles

A4.3.2.5.1.2.1. Remove - - - -

A4.3.2.5.1.2.2. Inspect - - - -

A4.3.2.5.1.2.3. Install - - - -

A4.3.2.5.1.3. Shroud

A4.3.2.5.1.3.1. Remove - - - -

A4.3.2.5.1.3.2. Inspect - - - -

A4.3.2.5.1.3.3. Install - - - -

A4.3.2.5.1.4. Stage 1 Blades

A4.3.2.5.1.4.1. Remove - - - -

A4.3.2.5.1.4.2. Inspect - - - -

A4.3.2.5.1.4.3. Install - - - -

A4.3.2.5.2. Low Pressure Turbine Section

*A4.3.2.5.2.1. Rotor

A4.3.2.5.2.1.1 Remove 2b - - -

A4.3.2.5.2.1.2. Inspect 1b - - -

A4.3.2.5.2.1.3. Install 2b - - -

*A4.3.2.5.2.2. Turbine Exhaust Frame

A4.3.2.5.2.2.1. Remove 2b - - -

A4.3.2.5.2.2.2. Inspect 1b - - -

A4.3.2.5.2.2.3. Install 2b - - -

*A4.3.2.5.2.3. Turbine Cases

A4.3.2.5.2.3.1. Remove 2b - - -

A4.3.2.5.2.3.2. Inspect 1b - - -

A4.3.2.5.2.3.3. Install 2b - - -

A4.3.2.5.2.4. Outer Transition Liner

A4.3.2.5.2.4.1. Remove - - - -

A4.3.2.5.2.4.2. Inspect - - - -

A4.3.2.5.2.4.3. Install - - - -

A4.3.2.5.2.5. Stage 3 Nozzle Segments

A4.3.2.5.2.5.1. Remove - - - -

A4.3.2.5.2.5.2. Inspect - - - -

A4.3.2.5.2.5.3. Install - - - -

*A4.3.2.5.2.6. C Sump Assembly

50
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.5.2.6.1. Remove 2b - - -

A4.3.2.5.2.6.2. Inspect 1b - - -

A4.3.2.5.2.6.3. Install 2b - - -

A4.3.2.5.3 Thrust Reverser

A4.3.2.5.3.1. Remove - - - -

A4.3.2.5.3.2. Inspect - - - -

A4.3.2.5.3.3. Install - - - -

A4.3.2.5.3.4. Rig - - - -

A4.3.2.5.4. Actuator

A4.3.2.5.4.1. Remove - - - -

A4.3.2.5.4.2. Inspect - - - -

A4.3.2.5.4.3. Install - - - -

A4.3.2.5.5. Blocker Door

A4.3.2.5.5.1. Remove - - - -

A4.3.2.5.5.2. Inspect - - - -

A4.3.2.5.5.3. Install - - - -

A4.3.2.5.6. Translating Cowl

A4.3.2.5.6.1. Remove - - - -

A4.3.2.5.6.2. Inspect - - - -

A4.3.2.5.6.3. Install - - - -

A4.3.2.5.7. Actuator Sync Cables

A4.3.2.5.7.1. Remove - - - -

A4.3.2.5.7.2. Inspect - - - -

A4.3.2.5.7.3. Install - - - -

A4.3.2.5.7.4. Rig - - - -

A4.3.2.5.8. Control Valve

A4.3.2.5.8.1. Remove - - - -

A4.3.2.5.8.2. Inspect - - - -

A4.3.2.5.8.3. Install - - - -

A4.3.2.5.9. Switch/Proximity

A4.3.2.5.9.1. Remove - - - -

A4.3.2.5.9.2. Inspect - - - -

A4.3.2.5.9.3. Install - - - -

A4.3.2.5.10. Pump

51
Attachment 4
 TF33, TF34, and F108
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Course 5 7 Course LVL LVL
Start Comp Initials Initials Initials
A4.3.2.5.10.1. Remove - - - -

A4.3.2.5.10.2. Inspect - - - -

A4.3.2.5.10.3. Install - - - -

A4.3.2.6. AIRCRAFT ENGINE MONITORING

SYSTEMS

A4.3.2.6.1. Operate, Input/Retrieve/Interpret Data - - - -

from Turbine Engine Monitoring
System (TEMS)/Quick Access
Recorder (QAR)/(MADAR)

52
Attachment 4
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 5

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on TF39 (C-5) engines.

A5.1 ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-5-14, 00-20 series, and
applicable aircraft/engine TOs
(A2.15.)
A5.1.1. Perform inspections

A5.1.1.1. Inlet and exhaust

- - - -
A5.1.1.2. Special inspections (Overspeed, over
temperature, etc) - - - -
A5.1.1.3. Fan exit fairing
- - - -
A5.1.1.4. Home station check
- - - -
A5.1.1.5. Isochronal (major/minor)
- - - -
A5.1.1.6. Clean gas turbine aircraft engines and
associated parts - - - -
TR: TO 2J-1-13
A5.1.1.7. Operate, input/retrieve/interpret data
from turbine/engine monitoring - - - -
system/MADARS (Operate caution,
warning and malfunction display,
etc.)
A5.2. ENGINE MAINTENANCE
TR: TOs 00-20-1, 00-35D-54,
1-1A-8, 2J-1-13, 2-1-111, and
applicable aircraft/engine TOs (A4.3.)
A5.2.1. Perform basic engine maintenance
functions
A5.2.1.1. First Stage Fan Blades

A5.2.1.1.1. Remove
- - - -
A5.2.1.1.2. Inspect/repair
- - - -
A5.2.1.1.3. Install
- - - -
A5.2.1.2. Second Stage Fan Blades

A5.2.1.2.1. Remove
- - - -
A5.2.1.2.2. Inspect/repair
- - - -
A5.2.1.2.3. Install
- - - -
A5.2.1.3. Fan Stator Stage 2

A5.2.1.3.1. Remove
- - - -

53
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.1.3.2. Inspect/repair
- - - -
A5.2.1.3.3. Install
- - - -
A5.2.1.4. Fan Frame

A5.2.1.4.1. Remove
- - - -
A5.2.1.4.2. Inspect/repair
- - - -
A5.2.1.4.3. Install
- - - -
A5.2.1.5. Inlet Gearbox

A5.2.1.5.1. Remove
- - - -
A5.2.1.5.2. Inspect/repair
- - - -
A5.2.1.5.3. Install
- - - -
A5.2.1.6. Fan shaft

A5.2.1.6.1. Remove
- - - -
A5.2.1.6.2. Inspect/repair
- - - -
A5.2.1.6.3. Install
- - - -
A5.2.1.7. Transfer Gearbox

A5.2.1.7.1. Remove
- - - -
A5.2.1.7.2. Inspect/repair
- - - -
A5.2.1.7.3. Install
- - - -
A5.2.1.8. Fuel pump filter

A5.2.1.8.1. Remove
- - - -
A5.2.1.8.2. Inspect/repair
- - - -
A5.2.1.8.3. Install
- - - -
A5.2.1.9. Compressor Rear Frame

A5.2.1.9.1. Remove
- - - -
A5.2.1.9.2. Inspect/repair
- - - -
A5.2.1.9.3. Install
- - - -
A5.2.1.10. Turbine Mid Frame

54
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.1.10.1. Remove
- - - -
A5.2.1.10.2. Inspect/repair
- - - -
A5.2.1.10.3. Install
- - - -
A5.2.1.11. Low Pressure Turbine Stator

A5.2.1.11.1. Remove
- - - -
A5.2.1.11.2. Inspect/repair
- - - -
A5.2.1.11.3. Install
- - - -
A5.2.1.12. Turbine Rear Frame

A5.2.1.12.1. Remove
- - - -
A5.2.1.12.2. Inspect/repair
- - - -
A5.2.1.12.3. Install
- - - -
A5.2.1.13. Forward scavenge pump (oil system)

A5.2.1.13.1. Remove
- - - -
A5.2.1.13.2. Inspect/repair
- - - -
A5.2.1.13.3. Install
- - - -
A5.2.1.14. Engine scavenge oil filter

A5.2.1.14.1. Remove
- - - -
A5.2.1.14.2. Inspect/repair
- - - -
A5.2.1.14.3. Install
- - - -
A5.2.1.15. Pneumatic fuel heater assembly

A5.2.1.15.1. Remove
- - - -
A5.2.1.15.2. Inspect/repair
- - - -
A5.2.1.15.3. Install
- - - -
A5.2.1.16. N1 Tach generator/Leads

A5.2.1.16.1. Remove
- - - -
A5.2.1.16.2. Inspect/repair
- - - -
A5.2.1.16.3. Install
- - - -

55
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.1.17. N2 Tach generator/Leads

A5.2.1.17.1. Remove
- - - -
A5.2.1.17.2. Inspect/repair
- - - -
A5.2.1.17.3. Install
- - - -
A5.2.1.18. Engine Accessories/QEC

A5.2.1.18.1. Vapor Barrier

A5.2.1.18.1.1. Remove
- - - -
A5.2.1.18.1.2. Inspect/repair
- - - -
A5.2.1.18.1.3. Install
- - - -
A5.2.1.18.2. T2c transducer

A5.2.1.18.2.1. Remove
- - - -
A5.2.1.18.2.2. Inspect/repair
- - - -
A5.2.1.18.2.3. Install
- - - -
A5.2.1.18.3. Pressure augmentor valve

A5.2.1.18.3.1. Remove
- - - -
A5.2.1.18.3.2. Inspect/repair
- - - -
A5.2.1.18.3.3. Install
- - - -
A5.2.1.18.4. Temperature augmentor valve

A5.2.1.18.4.1. Remove
- - - -
A5.2.1.18.4.2. Inspect/repair
- - - -
A5.2.1.18.4.3. Install
- - - -
A5.2.1.18.5. Engine anti-ice manifold

A5.2.1.18.5.1. Remove
- - - -
A5.2.1.18.5.2. Inspect/repair
- - - -
A5.2.1.18.5.3. Install
- - - -
A5.2.1.18.6. TR filter

A5.2.1.18.6.1. Remove
- - - -

56
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.1.18.6.2. Inspect/repair
- - - -
A5.2.1.18.6.3. Install
- - - -
A5.2.1.18.7. TR Electrical Harness

A5.2.1.18.7.1. Remove
- - - -
A5.2.1.18.7.2. Inspect/repair
- - - -
A5.2.1.18.7.3. Install
- - - -
A5.2.1.18.8. Fuel shutoff actuator

A5.2.1.18.8.1. Remove
- - - -
A5.2.1.18.8.2. Inspect/repair
- - - -
A5.2.1.18.8.3. Install
- - - -
A5.2.1.18.9. Cowl door

A5.2.1.18.9.1. Remove
- - - -
A5.2.1.18.9.2. Inspect/repair
- - - -
A5.2.1.18.9.3. Install
- - - -
A5.2.1.18.10. Engine fuel differential pressure
switch
A5.2.1.18.10.1. Remove
- - - -
A5.2.1.18.10.2. Inspect/repair
- - - -
A5.2.1.18.10.3. Install
- - - -
A5.2.1.18.11. Engine low fuel pressure switch

A5.2.1.18.11.1. Remove
- - - -
A5.2.1.18.11.2. Inspect/repair
- - - -
A5.2.1.18.11.3. Install
- - - -
A5.2.1.18.12. Engine air/oil separator

A5.2.1.18.12.1. Remove
- - - -
A5.2.1.18.12.2. Inspect/repair
- - - -
A5.2.1.18.12.3. Install
- - - -

57
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.2. ENGINE RIGGING
TR: Applicable aircraft/engine TOs
(A2.22)
A5.2.3. AIRCRAFT INSTALLED ENGINE
TESTING
TR: Applicable aircraft/engine TOs
(A2.24.)
A5.2.3.1. Engine operation

A5.2.3.1.1. Perform engine run (including pre-

ISO performance) - - - -
A5.2.3.1.2. Engine trim position “A” (trim box)
- - - -
A5.2.3.1.3. Engine trim position “B” (left
seat)/trim supervisor - - - -
A5.2.3.1.4. Perform ground observer/position
“C” duties during engine run - - - -
A5.2.3.1.5. Engine trim position “D” (trim
evaluator)/performance evaluation - - - -
A5.2.3.1.6. Deactivate/Activate Thrust Reversers
- - - -
A5.2.3.1.7. Install, operate and remove trim
equipment - - - -
A5.2.4. SMALL GAS TURBINE (SGT)
ENGINES, AUXILIARY POWER
UNITS (APU), OPERATING
PRINCIPLES
TR: Applicable engine TOs (A2.26.)
A5.2.4.1. Service/adjust

A5.2.4.1.1. Oil system

- - - -
A5.2.4.1.2. Fuel system
- - - -
A5.2.4.1.3. Electrical system
- - - -
A5.2.4.1.4. Pneumatic system
- - - -
A5.2.4.1.5. Inlet door and actuation system
- - - -
A5.2.4.1.6. Perform APU checks (including pre-
ISO) - - - -
A5.2.4.2. Remove/install Components On-
Equipment (Installed in Aircraft)
A5.2.4.2.1. APU
- - - -
A5.2.4.2.2. Generator
- - - -
A5.2.4.2.3. Fuel control
- - - -
A5.2.4.2.4. Fuel filter element
- - - -
A5.2.4.2.5. Fuel nozzle assembly
- - - -

58
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.2.6. Fuel start/bypass solenoid
- - - -
A5.2.4.2.7. Oil pressure switch
- - - -
A5.2.4.2.8. Oil filter element
- - - -
A5.2.4.2.9. Pneumatic ducting
- - - -
A5.2.4.2.10. Pneumatic control valve(s)
- - - -
A5.2.4.2.11. EGT thermocouple
- - - -
A5.2.4.2.12. Ignition exciter
- - - -
A5.2.4.2.13. Air inlet doors
- - - -
A5.2.4.2.14. Inlet door actuator
- - - -
A5.2.4.2.15. Electrical harness and cannon plugs
- - - -
A5.2.4.2.16. Starter/clutch/paw carrier
- - - -
A5.2.4.2.17. Oil pump
- - - -
A5.2.4.2.18. Fuel flow divider valve assembly
- - - -
A5.2.4.2.19. Combustion case drain valve
- - - -
A5.2.4.2.20. Voltage regulator/four speed box
- - - -
A5.2.4.2.21. Fan assembly vane axial (PMG)
- - - -
A5.2.4.3. APU Power plant operation

A5.2.4.3.1. On aircraft
- - - -
A5.2.4.3.2. Test cell
- - - -
A5.2.4.4. GTCP/165-1 (APU) Off-Equipment
Repair
A5.2.4.4.1. Generator

A5.2.4.4.1.1. Remove
- - - -
A5.2.4.4.1.2. Inspect/repair
- - - -
A5.2.4.4.1.3. Install
- - - -
A5.2.4.4.2. Fuel Control

A5.2.4.4.2.1. Remove
- - - -
A5.2.4.4.2.2. Inspect/repair
- - - -

59
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.4.2.3. Install
- - - -
A5.2.4.4.3. Fuel filter element

A5.2.4.4.3.1. Remove
- - - -
A5.2.4.4.3.2. Inspect/repair
- - - -
A5.2.4.4.3.3. Install
- - - -
A5.2.4.4.4. Fuel nozzle assembly

A5.2.4.4.4.1. Remove
- - - -
A5.2.4.4.4.2. Inspect/repair
- - - -
A5.2.4.4.4.3. Install
- - - -
A5.2.4.4.5. Start/servo fuel solenoid valve

A5.2.4.4.5.1. Remove
- - - -
A5.2.4.4.5.2. Inspect/repair
- - - -
A5.2.4.4.5.3. Install
- - - -
A5.2.4.4.6. Oil temperature/pressure switch

A5.2.4.4.6.1. Remove
- - - -
A5.2.4.4.6.2. Inspect/repair
- - - -
A5.2.4.4.6.3. Install
- - - -
A5.2.4.4.7. Oil filter element

A5.2.4.4.7.1. Remove
- - - -
A5.2.4.4.7.2. Inspect/repair
- - - -
A5.2.4.4.7.3. Install
- - - -
A5.2.4.4.8. Pneumatic ducting

A5.2.4.4.8.1. Remove
- - - -
A5.2.4.4.8.2. Inspect/repair
- - - -
A5.2.4.4.8.3. Install
- - - -
A5.2.4.4.9. Pneumatic control valve

A5.2.4.4.9.1. Remove
- - - -

60
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.4.9.2. Inspect/repair
- - - -
A5.2.4.4.9.3. Install
- - - -
A5.2.4.4.10. EGT thermocouple

A5.2.4.4.10.1. Remove
- - - -
A5.2.4.4.10.2. Inspect/repair
- - - -
A5.2.4.4.10.3. Install
- - - -
A5.2.4.4.11. Ignition cable/leads/plugs

A5.2.4.4.11.1. Remove
- - - -
A5.2.4.4.11.2. Inspect/repair
- - - -
A5.2.4.4.11.3. Install
- - - -
A5.2.4.4.12. Ignition exciter

A5.2.4.4.12.1. Remove
- - - -
A5.2.4.4.12.2. Inspect/repair
- - - -
A5.2.4.4.12.3. Install
- - - -
A5.2.4.4.13. Electrical harness and cannon plugs

A5.2.4.4.13.1. Remove
- - - -
A5.2.4.4.13.2. Inspect/repair
- - - -
A5.2.4.4.13.3. Install
- - - -
A5.2.4.4.14. Starter/clutch/paw carrier

A5.2.4.4.14.1. Remove
- - - -
A5.2.4.4.14.2. Inspect/repair
- - - -
A5.2.4.4.14.3. Install
- - - -
A5.2.4.4.15. Oil pump

A5.2.4.4.15.1. Remove
- - - -
A5.2.4.4.15.2. Inspect/repair
- - - -
A5.2.4.4.15.3. Install
- - - -
A5.2.4.4.16. Fuel flow divider valve assembly

61
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.4.16.1. Remove
- - - -
A5.2.4.4.16.2. Inspect/repair
- - - -
A5.2.4.4.16.3. Install
- - - -
A5.2.4.4.17. Combustion case drain valve

A5.2.4.4.17.1. Remove
- - - -
A5.2.4.4.17.2. Inspect/repair
- - - -
A5.2.4.4.17.3. Install
- - - -
A5.2.4.4.18. Voltage regulator/four speed box

A5.2.4.4.18.1. Remove
- - - -
A5.2.4.4.18.2. Inspect/repair
- - - -
A5.2.4.4.18.3. Install
- - - -
A5.2.4.4.19. Cooling fan assembly

A5.2.4.4.19.1. Remove
- - - -
A5.2.4.4.19.2. Inspect/repair
- - - -
A5.2.4.4.19.3. Install
- - - -
A5.2.4.4.20. Oil temperature regulator (oil cooler)

A5.2.4.4.20.1. Remove
- - - -
A5.2.4.4.20.2. Inspect/repair
- - - -
A5.2.4.4.20.3. Install
- - - -
A5.2.4.4.21. Fuel bypass valve

A5.2.4.4.21.1. Remove
- - - -
A5.2.4.4.21.2. Inspect/repair
- - - -
A5.2.4.4.21.3. Install
- - - -
A5.2.4.4.22. Impeller

A5.2.4.4.22.1. Remove
- - - -
A5.2.4.4.22.2. Inspect/repair
- - - -
A5.2.4.4.22.3. Install
- - - -

62
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.4.22. Impeller shroud

A5.2.4.4.22.1. Remove
- - - -
A5.2.4.4.22.2. Inspect/repair
- - - -
A5.2.4.4.22.3. Install
- - - -
A5.2.4.4.23. 1st stage turbine wheel

A5.2.4.4.23.1. Remove
- - - -
A5.2.4.4.23.2. Inspect/repair
- - - -
A5.2.4.4.23.3. Install
- - - -
A5.2.4.4.24. 2nd stage turbine wheel

A5.2.4.4.24.1. Remove
- - - -
A5.2.4.4.24.2. Inspect/repair
- - - -
A5.2.4.4.24.3. Install
- - - -
A5.2.4.4.25. 1st stage turbine stator

A5.2.4.4.25.1. Remove
- - - -
A5.2.4.4.25.2. Inspect/repair
- - - -
A5.2.4.4.25.3. Install
- - - -
A5.2.4.4.26. 2nd stage turbine stator

A5.2.4.4.26.1. Remove
- - - -
A5.2.4.4.26.2. Inspect/repair
- - - -
A5.2.4.4.26.3. Install
- - - -
A5.2.4.4.27. Turbine bearing support

A5.2.4.4.27.1. Remove
- - - -
A5.2.4.4.27.2. Inspect/repair
- - - -
A5.2.4.4.27.3. Install
- - - -
A5.2.4.4.28. Turbine plenum

A5.2.4.4.28.1. Remove
- - - -
A5.2.4.4.28.2. Inspect/repair
- - - -

63
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.4.28.3. Install
- - - -
A5.2.4.4.29. Diffuser

A5.2.4.4.29.1. Remove
- - - -
A5.2.4.4.29.2. Inspect/repair
- - - -
A5.2.4.4.29.3. Install
- - - -
A5.2.4.4.30. Combustion chamber

A5.2.4.4.30.1. Remove
- - - -
A5.2.4.4.30.2. Inspect/repair
- - - -
A5.2.4.4.30.3. Install
- - - -
A5.2.4.4.31. Bearings/seals

A5.2.4.4.31.1. Remove
- - - -
A5.2.4.4.31.2. Inspect/repair
- - - -
A5.2.4.4.31.3. Install
- - - -
A5.2.4.4.32. Tailpipe

A5.2.4.4.32.1. Remove
- - - -
A5.2.4.4.32.2. Inspect/repair
- - - -
A5.2.4.4.32.3. Install
- - - -
A5.2.4.4.33. Tailpipe extension

A5.2.4.4.33.1. Remove
- - - -
A5.2.4.4.33.2. Inspect/repair
- - - -
A5.2.4.4.33.3. Install
- - - -
A5.2.4.4.34. APU plumbing

A5.2.4.4.34.1. Remove
- - - -
A5.2.4.4.34.2. Inspect/repair
- - - -
A5.2.4.4.34.3. Install
- - - -
A5.2.4.4.35. Inlet plenum

A5.2.4.4.35.1. Remove
- - - -

64
 2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A5.2.4.4.35.2. Inspect/repair
- - - -
A5.2.4.4.35.3. Install
- - - -
A5.2.4.4.36. Accessory drive gearbox

A5.2.4.4.36.1. Remove
- - - -
A5.2.4.4.36.2. Inspect/repair
- - - -
A5.2.4.4.36.3. Install
- - - -

65
66
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 6

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on JT-8 (C-9) engines.

A6.1. ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-5-14, 00-20 series,
and applicable aircraft/engine
TOs (A2.19.)
A6.1.1. Perform inspections

A6.1.1.1. Inlet and exhaust * - - - -

A6.1.1.2. 1st Stage Fan Blades * - - - -
A6.1.1.3. 2nd Stage Fan Blades * - - - -
A6.1.1.4. Inlet guides vanes * - - - -
A6.1.1.5. Compressor * - - - -
A6.1.1.6. Combustion section * - - - -
A6.1.1.7. Turbine case * - - - -
A6.1.1.8. Nozzle guide vane * - - - -
A6.1.1.9. Low pressure turbine * - - - -
A6.1.1.10. Special inspections (Overspeed, - - - -
over temperature, etc)
A6.1.1.11. Home station check * - - - -
A6.1.1.12. Isochronal (major/minor) * - - - -
A6.1.1.13. CLEAN GAS TURBINE - - - -
AIRCRAFT ENGINES AND
ASSOCIATED PARTS
TR: TO 2J-1-13 and applicable
aircraft TOs
A6.1.1.14. Fuel filter differential pressure - - - -
checks
A6.1.2. ENGINE ACCESSORIES
TR: TOs 00-20-1, 00-350-54,
1-1A-8, 2J-1-13, and 2-1-111
A6.1.2.1. Remove and install engine
system components
A6.1.2.1.1. Thermostatic/air regulator

A6.1.2.1.1.1. Remove - - - -
A6.1.2.1.1.2. Install - - - -
A6.1.2.1.2. Thrust reverser driver link

67
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.2.1.2.1. Remove - - - -
A6.1.2.1.2.2. Rig - - - -
A6.1.2.1.2.3. Install - - - -
A6.1.2.1.3. Thrust reverser idler link

A6.1.2.1.3.1. Remove - - - -
A6.1.2.1.3.2. Install - - - -
A6.1.2.1.4. Thrust reverser unlock latch

A6.1.2.1.4.1. Remove - - - -
A6.1.2.1.4.2. Inspect - - - -
A6.1.2.1.4.3. Install - - - -
A6.1.2.1.5. Thrust reverser unlock cable

A6.1.2.1.5.1. Remove - - - -
A6.1.2.1.5.2. Inspect - - - -
A6.1.2.1.5.3. Install - - - -
A6.1.2.1.6. Thrust reverser interlock cable

A6.1.2.1.6.1. Remove - - - -
A6.1.2.1.6.2. Inspect - - - -
A6.1.2.1.6.3. Install - - - -
A6.1.2.1.7. Upper and Lower Cowling Doors

A6.1.2.1.7.1. Remove - - - -
A6.1.2.1.7.2. Inspect - - - -
A6.1.2.1.7.3. Install - - - -
A6.1.2.1.8. Engine fuel differential pressure
switch
A6.1.2.1.8.1. Remove - - - -
A6.1.2.1.8.2. Install - - - -
A6.1.2.1.9. Pneumatic fuel heater assembly

A6.1.2.1.9.1. Remove - - - -

68
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.2.1.9.2. Install - - - -
A6.1.2.1.10. Low Inlet Fuel Pressure Switch

A6.1.2.1.10.1. Remove - - - -
A6.1.2.1.10.2. Install - - - -
A6.1.2.1.11. Fuel heat shutoff valve

A6.1.2.1.11.1. Remove - - - -
A6.1.2.1.11.2. Inspect - - - -
A6.1.2.1.11.3. Install - - - -
A6.1.2.1.12. Powerplant Conversion
Ref: 1C9A-10
A6.1.2.1.12.1. Remove - - - -
A6.1.2.1.12.2. Inspect - - - -
A6.1.2.1.12.3. Install - - - -
A6.1.2.1.13. PRBC Pressure Ratio Bleed
Control Valve
A6.1.2.1.13.1. Remove - - - -
A6.1.2.1.13.2. Inspect - - - -
A6.1.2.1.13.3. Install - - - -
A6.1.2.2. Engine Rigging
TR: Applicable aircraft/engine
TOs (A2.22.)
A6.1.2.2.1. Thrust Reverser Unlock System - - - -
A6.1.2.2.2. Thrust reverser interlock system - - - -
A6.1.3. AIRCRAFT INSTALLED
ENGINE TESTING
TR: Applicable aircraft/engine
TOs (A2.24.)
A6.1.3.1 Engine operation

A6.1.3.1.1. Operate VHF/UHF aircraft - - - -

communications
A6.1.3.1.2. Engine trim position “A” (left - - - -
seat)
A6.1.3.1.3. Engine trim position “B” (right - - - -
seat)
A6.1.3.1.4. Perform ground observer/position - - - -
“C” duties during engine run
A6.1.3.1.5. Engine trim position “D” - - - -
performance evaluation/trim box

69
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.3.1.6. Install, operate, and remove trim - - - -
equipment
A6.1.3.1.7. Perform engine run (including - - - -
pre-ISO performance)
A6.1.3.1.8. Deactivate/Activate Thrust - - - -
Reversers
A6.1.3.1.9. Perform Audible check on - - - -
Ignition System
A6.1.4. SMALL GAS TURBINE (SGT)
ENGINES, AUXILIARY
POWER UNITS (APU), QUICK
START AUXILIARY POWER
SYSTEM (QSAS) OPERATING
PRINCIPLES
TR: Applicable engine TOs
(A2.26.)
A6.1.4.1. Oil system - - - -
A6.1.4.2. Fuel system - - - -
A6.1.4.3. Electrical system - - - -
A6.1.4.4. Pneumatic system - - - -
A6.1.4.5. Enclosure - - - -
A6.1.4.6. Inlet door and actuation system - - - -
A6.1.4.7. Perform APU checks (including - - - -
pre-ISO)
A6.1.4.7.1. APU

A6.1.4.7.1.1. Remove - - - -
A6.1.4.7.1.2. Inspect - - - -
A6.1.4.7.1.3. Install - - - -
A6.1.4.7.2. Generator

A6.1.4.7.2.1. Remove - - - -
A6.1.4.7.2.2. Inspect - - - -
A6.1.4.7.2.3. Install - - - -
A6.1.4.7.3. Fuel control

A6.1.4.7.3.1. Remove - - - -
A6.1.4.7.3.2. Inspect - - - -
A6.1.4.7.3.3. Adjust - - - -

70
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.4.7.3.4. Install - - - -
A6.1.4.7.4. Low Fuel Pressure Filter

A6.1.4.7.4.1. Remove - - - -
A6.1.4.7.4.2. Install - - - -
A6.1.4.7.5. Fuel Control filter elements

A6.1.4.7.5.1. Remove - - - -
A6.1.4.7.5.2. Inspect - - - -
A6.1.4.7.5.3. Install - - - -
A6.1.4.7.6. Fuel Atomizer Assembly

A6.1.4.7.6.1. Remove - - - -
A6.1.4.7.6.2. Inspect - - - -
A6.1.4.7.6.3. Install - - - -
A6.1.4.7.7. Fuel Solenoid Valve

A6.1.4.7.7.1. Remove - - - -
A6.1.4.7.7.2. Inspect - - - -
A6.1.4.7.7.3. Install - - - -
A6.1.4.7.8. Oil Tank

A6.1.4.7.8.1. Remove - - - -
A6.1.4.7.8.2. Inspect - - - -
A6.1.4.7.8.3. Install - - - -
A6.1.4.7.9. Oil Temperature Sensor

A6.1.4.7.9.1. Remove - - - -
A6.1.4.7.9.2. Inspect - - - -
A6.1.4.7.9.3. Install - - - -
A6.1.4.7.10. Oil Pressure Sequencing Switch

A6.1.4.7.10.1. Remove - - - -
A6.1.4.7.10.2. Install - - - -

71
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.4.7.11. Low Oil Pressure Switch

A6.1.4.7.11.1. Remove - - - -
A6.1.4.7.11.2. Install - - - -
A6.1.4.7.12. Oil Pressure Relief Valve

A6.1.4.7.12.1. Remove - - - -
A6.1.4.7.12.2. Adjust - - - -
A6.1.4.7.12.3. Install - - - -
A6.1.4.7.13. Oil Pump Cluster

A6.1.4.7.13.1. Remove - - - -
A6.1.4.7.13.2. Install - - - -
A6.1.4.7.14. Oil filter element

A6.1.4.7.14.1. Remove - - - -
A6.1.4.7.14.2. Inspect - - - -
A6.1.4.7.14.3. Install - - - -
A6.1.4.7.15. Pneumatic ducting

A6.1.4.7.15.1. Remove - - - -
A6.1.4.7.15.2. Inspect - - - -
A6.1.4.7.15.3. Install - - - -
A6.1.4.7.16. EGT thermocouple

A6.1.4.7.16.1. Remove - - - -
A6.1.4.7.16.2. Inspect - - - -
A6.1.4.7.16.3. Install - - - -
A6.1.4.7.17. Load control thermostat

A6.1.4.7.17.1. Remove - - - -
A6.1.4.7.17.2. Inspect - - - -
A6.1.4.7.17.3. Adjust - - - -
A6.1.4.7.17.4. Install - - - -

72
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.4.7.18. Load Control Switcher Valve

A6.1.4.7.18.1. Remove - - - -
A6.1.4.7.18.2. Install - - - -
A6.1.4.7.19. Ignition exciter

A6.1.4.7.19.1. Remove - - - -
A6.1.4.7.19.2. Inspect - - - -
A6.1.4.7.19.3. Install - - - -
A6.1.4.7.20. Ignition Lead

A6.1.4.7.20.1. Remove - - - -
A6.1.4.7.20.2. Inspect - - - -
A6.1.4.7.20.3. Install - - - -
A6.1.4.7.21. Air inlet doors

A6.1.4.7.21.1. Remove - - - -
A6.1.4.7.21.2. Inspect - - - -
A6.1.4.7.21.3. Rig - - - -
A6.1.4.7.21.4. Install - - - -
A6.1.4.7.22. Inlet door actuator

A6.1.4.7.22.1. Remove - - - -
A6.1.4.7.22.2. Inspect - - - -
A6.1.4.7.22.3. Rig - - - -
A6.1.4.7.22.4. Install - - - -
A6.1.4.7.23. Starter

A6.1.4.7.23.1. Remove - - - -
A6.1.4.7.23.2. Inspect - - - -
A6.1.4.7.23.3. Install - - - -
A6.1.4.7.24. Combustion Chamber

A6.1.4.7.24.1. Remove - - - -

73
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.4.7.24.2. Inspect - - - -
A6.1.4.7.24.3. Install - - - -
A6.1.4.7.25. Combustion case drain valve

A6.1.4.7.25.1. Remove - - - -
A6.1.4.7.25.2. Install - - - -
A6.1.4.7.26. Centrifugal (3 Speed) Switch

A6.1.4.7.26.1. Remove - - - -
A6.1.4.7.26.2. Inspect - - - -
A6.1.4.7.26.3. Install - - - -
A6.1.4.7.27. Cooling fan assembly

A6.1.4.7.27.1. Remove - - - -
A6.1.4.7.27.2. Install - - - -
A6.1.4.7.28. Interlock Switch

A6.1.4.7.28.1. Remove - - - -
A6.1.4.7.28.2. Install - - - -
A6.1.4.7.29. Air/Oil Cooler

A6.1.4.7.29.1. Remove - - - -
A6.1.4.7.29.2. Inspect - - - -
A6.1.4.7.29.3. Install - - - -
A6.1.4.7.30. Air pressure regulator

A6.1.4.7.30.1. Remove - - - -
A6.1.4.7.30.2. Inspect - - - -
A6.1.4.7.30.3. Adjust - - - -
A6.1.4.7.30.4. Install - - - -
A6.1.4.7.31. Load control valve

A6.1.4.7.31.1. Remove - - - -
A6.1.4.7.31.2. Inspect - - - -

74
Attachment 6
 JT-8 (C-9)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A6.1.4.7.31.3. Adjust - - - -
A6.1.4.7.31.4. Install - - - -
A6.1.4.7.32. Air Box

A6.1.4.7.32.1. Remove - - - -
A6.1.4.7.32.2. Inspect - - - -
A6.1.4.7.32.3. Install - - - -
A6.1.4.7.33. Mount and Vibration Insulators

A6.1.4.7.33.1. Remove - - - -
A6.1.4.7.33.2. Inspect - - - -
A6.1.4.7.33.3. Install - - - -
A6.1.4.7.34. Tach Generator

A6.1.4.7.34.1. Remove - - - -
A6.1.4.7.34.2. Install - - - -
A6.1.4.7.35. APU operation

A6.1.4.7.35.1. On aircraft - - - -
A6.1.4.7.35.2. Test Stand - - - -

75
Attachment 6
76
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 7

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on F-108 (KC135 R/T) engines.

A7.1. ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-5-14, 00-20 series,
and applicable aircraft/engine
TOs (A2.19.)
A7.1.1. Perform inspections

A7.1.1.1. Inlet and exhaust * - - - -

A7.1.1.2. Fan and booster * - - - -
A7.1.1.3. High speed compressor * - - - -
A7.1.1.4. Forward stator cases - - - -
A7.1.1.5. Rear stator cases - - - -
A7.1.1.6. Compressor discharge nozzle - - - -
(CDN) case
A7.1.1.7. Combustion chamber * - - - -
A7.1.1.8. High speed turbine * - - - -
A7.1.1.9. High pressure turbine nozzle * - - - -
A7.1.1.10. 1st stage LPT nozzle/high * - - - -
pressure turbine shroud
A7.1.1.11. Low pressure turbine * - - - -
A7.1.1.12. Low pressure turbine case - - - -
A7.1.1.13. Turbine frame - - - -
A7.1.1.14. Special inspections (Overspeed, * - - - -
over temperature, etc)
TR: TO 1C-133A-6
A7.1.1.15. Home station check * - - - -
TR: Applicable 24XXX and
27XXX items
A7.1.1.16. Isochronal (major/minor) - - - -
A7.1.1.17. Clean gas turbine aircraft engines - - - -
and associated parts
TR: TO 2J-1-13
A7.1.1.18. Fuel filter differential pressure - - - -
checks
A7.1.1.19. Operate, input/retrieve/interpret - - - -
data from turbine/engine
monitoring system

Attachment 7
77
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2. ENGINE MAINTENANCE
TR: TOs 00-20-1, 00-35D-54,
1-1A-8, 2J-1-13, 2-1-111, and
applicable aircraft/engine TOs
(A4.3.)
A7.2.1. Perform preliminary maintenance
procedures
A7.2.1.1. Apply external pneumatic power - - - -
A7.2.2. Perform engine maintenance

A7.2.2.1. Fan outlet guide vanes

A7.2.2.1.1. Remove - - - -
A7.2.2.1.2. Inspect - - - -
A7.2.2.1.3. Install - - - -
A7.2.2.2. Acoustical panels

A7.2.2.2.1. Remove - - - -
A7.2.2.2.2. Inspect * - - - -
A7.2.2.2.3. Install - - - -
A7.2.2.3. Idle reset solenoid

A7.2.2.3.1. Remove - - - -
A7.2.2.3.2. Inspect - - - -
A7.2.2.3.3. Install - - - -
A7.2.2.4. Bleed valve and master ball
screw actuator assembly
A7.2.2.4.1. Remove * - - - -
A7.2.2.4.2. Inspect * - - - -
A7.2.2.4.3. Install * - - - -
A7.2.2.5. Bleed valve and ball screw
actuator assembly
A7.2.2.5.1. Remove * - - - -
A7.2.2.5.2. Inspect * - - - -
A7.2.2.5.3. Install * - - - -
A7.2.2.6. VBV stop mechanism

Attachment 7
78
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.2.6.1. Remove * - - - -
A7.2.2.6.2. Inspect * - - - -
A7.2.2.6.3. Install * - - - -
A7.2.2.7. VBV fuel gear motor

A7.2.2.7.1. Remove * - - - -
A7.2.2.7.2. Inspect * - - - -
A7.2.2.7.3. Install * - - - -
A7.2.2.8. VBV feedback cable

A7.2.2.8.1. Remove - - - -
A7.2.2.8.2. Inspect - - - -
A7.2.2.8.3. Install - - - -
A7.2.2.9. High pressure turbine clearance
control valve
A7.2.2.9.1. Remove - - - -
A7.2.2.9.2. Inspect - - - -
A7.2.2.9.3. Install - - - -
A7.2.2.10. N1 speed sensor

A7.2.2.10.1. Remove - - - -
A7.2.2.10.2. Inspect - - - -
A7.2.2.10.3. Install - - - -
A7.2.2.11. N2 control alternator

A7.2.2.11.1. Remove - - - -
A7.2.2.11.2. Inspect - - - -
A7.2.2.11.3. Install - - - -
A7.2.2.12. Power management control

A7.2.2.12.1. Remove - - - -
A7.2.2.12.2. Inspect - - - -
A7.2.2.12.3. Install * - - - -

Attachment 7
79
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.2.13. T-12 sensor

A7.2.2.13.1. Remove - - - -
A7.2.2.13.2. Inspect - - - -
A7.2.2.13.3. Install - - - -
A7.2.2.14. LPT cooling manifold

A7.2.2.14.1. Remove - - - -
A7.2.2.14.2. Inspect - - - -
A7.2.2.14.3. Install - - - -
A7.2.2.15. Transfer gearbox

A7.2.2.15.1. Remove - - - -
A7.2.2.15.2. Inspect - - - -
A7.2.2.15.3. Install - - - -
A7.2.2.16. Accessory gearbox

A7.2.2.16.1. Remove - - - -
A7.2.2.16.2. Inspect - - - -
A7.2.2.16.3. Install - - - -
A7.2.2.17. Quick Engine Change (QEC)
components
A7.2.2.17.1. 5th stage bleed air check valve

A7.2.2.17.1.1. Remove - - - -
A7.2.2.17.1.2. Inspect - - - -
A7.2.2.17.1.3. Install - - - -
A7.2.2.17.2. Speed control box

A7.2.2.17.2.1. Remove - - - -
A7.2.2.17.2.2. Inspect - - - -
A7.2.2.17.2.3. Install - - - -
A7.2.2.18. ENGINE RIGGING
TR: Applicable aircraft/engine
TOs (A2.22)

Attachment 7
80
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.2.18.1. Rig engine variable stator vane * - - - -
(VSV) feedback cable
A7.2.2.18.2. Rig MEC/throttle cable * - - - -
A7.2.2.18.3. PMC test - - - -
A7.2.2.18.4. PLA gain adjustment - - - -
A7.2.3. AIRCRAFT INSTALLED
ENGINE TESTING
TR: Applicable aircraft/engine
TOs (A2.24.)
A7.2.3.1. Engine operation

A7.2.3.1.1. Perform engine run (including - - - -

pre-ISO performance)
A7.2.3.1.2. Engine trim position “A” (left - - - -
seat)
A7.2.3.1.3. Engine trim position “B” (right - - - -
seat)/trim supervisor
A7.2.3.1.4. Perform ground observer/position - - - -
“C” duties during engine run
A7.2.3.1.5. Fan trim balance - - - -
A7.2.3.1.6. Audible ignition system check- - - - -
out
A7.2.3.1.7. Install, operate and remove trim - - - -
equipment
A7.2.4. SMALL GAS TURBINE (SGT)
ENGINES, AUXILIARY
POWER UNITS (APU), QUICK
START AUXILIARY POWER
SYSTEM (QSAS) OPERATING
PRINCIPLES
TR: Applicable engine TOs
(A2.22.)
A7.2.4.1. Service/adjust

A7.2.4.1.1. Service oil system - - - -

A7.2.4.1.2. Enclosure - - - -
A7.2.4.1.3. Adjust/repair door actuation - - - -
system
A7.2.4.1.4. Perform APU/QSAS checks - - - -
(including pre-ISO)
A7.2.4.2. Perform APU maintenance

A7.2.4.2.1. APU

A7.2.4.2.1.1. Remove * - - - -
A7.2.4.2.1.2. Inspect * - - - -

Attachment 7
81
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.4.2.1.3. Install * - - - -
A7.2.4.2.2. APU enclosure

A7.2.4.2.2.1. Remove - - - -
A7.2.4.2.2.2. Inspect - - - -
A7.2.4.2.2.3. Install - - - -
A7.2.4.2.3. Air filter

A7.2.4.2.3.1. Remove - - - -
A7.2.4.2.3.2. Inspect - - - -
A7.2.4.2.3.3. Install - - - -
A7.2.4.2.4. Main fuel solenoid valve

A7.2.4.2.4.1. Remove - - - -
A7.2.4.2.4.2. Inspect - - - -
A7.2.4.2.4.3. Install - - - -
A7.2.4.2.5. Start fuel solenoid valve

A7.2.4.2.5.1. Remove - - - -
A7.2.4.2.5.2. Inspect - - - -
A7.2.4.2.5.3. Install - - - -
A7.2.4.2.6. IGV actuator

A7.2.4.2.6.1. Remove - - - -
A7.2.4.2.6.2. Inspect - - - -
A7.2.4.2.6.3. Install - - - -
A7.2.4.2.7. RTD compressor

A7.2.4.2.7.1. Remove - - - -
A7.2.4.2.7.2. Inspect - - - -
A7.2.4.2.7.3. Install - - - -
A7.2.4.2.8. Air flow sensor

A7.2.4.2.8.1. Remove - - - -

Attachment 7
82
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.4.2.8.2. Inspect - - - -
A7.2.4.2.8.3. Install - - - -
A7.2.4.2.9. Oil tank

A7.2.4.2.9.1. Remove - - - -
A7.2.4.2.9.2. Inspect - - - -
A7.2.4.2.9.3. Install - - - -
A7.2.4.2.10. Inlet muff

A7.2.4.2.10.1. Remove - - - -
A7.2.4.2.10.2. Inspect - - - -
A7.2.4.2.10.3. Install - - - -
A7.2.4.2.11. Generator

A7.2.4.2.11.1. Remove - - - -
A7.2.4.2.11.2. Inspect - - - -
A7.2.4.2.11.3. Install - - - -
A7.2.4.2.12. Fuel control

A7.2.4.2.12.1. Remove - - - -
A7.2.4.2.12.2. Inspect - - - -
A7.2.4.2.12.3. Install - - - -
A7.2.4.2.13. Fuel filter element

A7.2.4.2.13.1. Remove - - - -
A7.2.4.2.13.2. Inspect - - - -
A7.2.4.2.13.3. Install - - - -
A7.2.4.2.14. Start fuel nozzle/purge restrictor

A7.2.4.2.14.1. Remove - - - -
A7.2.4.2.14.2. Inspect * - - - -
A7.2.4.2.14.3. Install * - - - -
A7.2.4.2.15. Servo fuel valve

Attachment 7
83
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.4.2.15.1. Remove - - - -
A7.2.4.2.15.2. Inspect - - - -
A7.2.4.2.15.3. Install - - - -
A7.2.4.2.16. Oil temperature switch

A7.2.4.2.16.1. Remove - - - -
A7.2.4.2.16.2. Inspect - - - -
A7.2.4.2.16.3. Install - - - -
A7.2.4.2.17. Oil pressure switch

A7.2.4.2.17.1. Remove - - - -
A7.2.4.2.17.2. Inspect - - - -
A7.2.4.2.17.3. Install - - - -
A7.2.4.2.18. Oil filter element

A7.2.4.2.18.1. Remove - - - -
A7.2.4.2.18.2. Inspect - - - -
A7.2.4.2.18.3. Install - - - -
A7.2.4.2.19. Pneumatic ducting

A7.2.4.2.19.1. Remove - - - -
A7.2.4.2.19.2. Inspect - - - -
A7.2.4.2.19.3. Install - - - -
A7.2.4.2.20. Surge control valve

A7.2.4.2.20.1. Remove - - - -
A7.2.4.2.20.2. Inspect - - - -
A7.2.4.2.20.3. Install - - - -
A7.2.4.2.21. EGT thermocouple

A7.2.4.2.21.1. Remove - - - -
A7.2.4.2.21.2. Inspect - - - -
A7.2.4.2.21.3. Install - - - -

Attachment 7
84
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.4.2.22. Fire detector loop (upper/lower)

A7.2.4.2.22.1. Remove - - - -
A7.2.4.2.22.2. Inspect - - - -
A7.2.4.2.22.3. Install - - - -
A7.2.4.2.23. Ignition lead

A7.2.4.2.23.1. Remove - - - -
A7.2.4.2.23.2. Inspect - - - -
A7.2.4.2.23.3. Install - - - -
A7.2.4.2.24. Ignition exciter

A7.2.4.2.24.1. Remove - - - -
A7.2.4.2.24.2. Inspect - - - -
A7.2.4.2.24.3. Install - - - -
A7.2.4.2.25. Inlet/exhaust doors

A7.2.4.2.25.1. Remove - - - -
A7.2.4.2.25.2. Inspect - - - -
A7.2.4.2.25.3. Install - - - -
A7.2.4.2.26. Door actuator

A7.2.4.2.26.1. Remove - - - -
A7.2.4.2.26.2. Inspect - - - -
A7.2.4.2.26.3. Install - - - -
A7.2.4.2.27. Electrical harness and cannon
plugs
A7.2.4.2.27.1. Remove - - - -
A7.2.4.2.27.2. Inspect - - - -
A7.2.4.2.27.3. Install - - - -
A7.2.4.2.28. Starter

A7.2.4.2.28.1. Remove - - - -
A7.2.4.2.28.2. Inspect - - - -

Attachment 7
85
 F-108 (KC 135 R/T)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A7.2.4.2.28.3. Install - - - -
A7.2.4.2.29. Oil return manifold

A7.2.4.2.29.1. Remove - - - -
A7.2.4.2.29.2. Inspect - - - -
A7.2.4.2.29.3. Install - - - -
A7.2.4.2.30. Fuel manifold assembly

A7.2.4.2.30.1. Remove - - - -
A7.2.4.2.30.2. Inspect - - - -
A7.2.4.2.30.3. Install - - - -
A7.2.4.2.31. Ejector pump

A7.2.4.2.31.1. Remove - - - -
A7.2.4.2.31.2. Inspect * - - - -
A7.2.4.2.31.3. Install * - - - -
A7.2.4.2.32. Electronic Sequence Control Unit
(ESCU)
A7.2.4.2.32.1. Remove - - - -
A7.2.4.2.32.2. Inspect - - - -
A7.2.4.2.32.3. Install - - - -
A7.2.4.2.33. RTD ambient

A7.2.4.2.33.1. Remove - - - -
A7.2.4.2.33.2. Inspect - - - -
A7.2.4.2.33.3. Install - - - -
A7.2.4.2.34. Magnetic pick-up

A7.2.4.2.34.1. Remove - - - -
A7.2.4.2.34.2. Inspect - - - -
A7.2.4.2.34.3. Install - - - -
A7.2.4.3. QSAS power plant operation * - - - -

Attachment 7
86
 CF6-50 (KC-10)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 8

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on CF6-50 (KC-10) engines.

A8.1. ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-5-14, 00-20 series,
and applicable aircraft/engine
TOs (A2.15.)
A8.1.1. Perform inspections

A8.1.1.1. Inlet and exhaust - - - -

A8.1.1.2. Special inspections (Overspeed, - - - -
over temperature, etc)
A8.1.1.3. Fan exit fairing - - - -
A8.1.1.4. Isochronal (major/minor) - - - -
A8.1.1.5. Clean gas turbine aircraft engines - - - -
and associated parts
TR: TO 2J-1-13
A8.1.1.6. Fuel filter differential pressure - - - -
checks
A8.2. ENGINE MAINTENANCE
TR: TOs 00-20-1, 00-35D-54,
1-1A-8, 2J-1-13, 2-1-111, and
applicable aircraft/engine TOs
(A4.3.)
A8.2.1. Perform maintenance functions

A8.2.1.1. Nozzles

A8.2.1.1.1. Remove - - - -
A8.2.1.1.2. Inspect - - - -
A8.2.1.1.3. Install - - - -
A8.2.1.2. Thrust reverser/actuator/drive
door
A8.2.1.2.1. Remove - - - -
A8.2.1.2.2. Inspect - - - -
A8.2.1.2.3. Install - - - -
A8.2.1.3. Bleed valve actuator

A8.2.1.3.1. Remove - - - -
A8.2.1.3.2. Inspect - - - -

Attachment 8
87
 CF6-50 (KC-10)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A8.2.1.3.3. Install - - - -
A8.2.1.4. N1 speed sensor

A8.2.1.4.1. Remove - - - -
A8.2.1.4.2. Inspect - - - -
A8.2.1.4.3. Install - - - -
A8.2.1.5. N2 speed sensor

A8.2.1.5.1. Remove - - - -
A8.2.1.5.2. Inspect - - - -
A8.2.1.5.3. Install - - - -
A8.2.1.6. Engine fuel differential pressure
switch
A8.2.1.6.1. Remove - - - -
A8.2.1.6.2. Inspect - - - -
A8.2.1.6.3. Install - - - -
A8.2.1.7. Sound suppression panels

A8.2.1.7.1. Remove - - - -
A8.2.1.7.2. Inspect - - - -
A8.2.1.7.3. Install - - - -
A8.2.1.8. Bleed valve actuator and linkage

A8.2.1.8.1. Remove - - - -
A8.2.1.8.2. Inspect - - - -
A8.2.1.8.3. Install - - - -
A8.2.1.9. Inspect engine system
components
A8.2.1.9.1. Thrust reverser actuator/drive - - - -
motor
A8.2.1.9.2. Cowl doors (e.g., Forward, AFT, - - - -
fan cowls, ducts)
A8.2.1.9.3. Engine fuel differential pressure - - - -
switch
A8.2.1.10. Engine

Attachment 8
88
 CF6-50 (KC-10)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A8.2.1.10.1. Remove - - - -
A8.2.1.10.2. Install - - - -
A8.2.2. ENGINE RIGGING
TR: Applicable Aircraft/engine
TOs (A2.18.)
A8.2.2.1. Rig variable stator vane/bypass - - - -
valve actuators/bleed valves
A8.2.2.2. Rig MEC cable - - - -
A8.2.3. AIRCRAFT INSTALLED
ENGINE TESTING
TR: Applicable aircraft/engine
TOs (A2.20.)
A8.2.3.1. Engine operation

A8.2.3.1.1. Perform engine run (including - - - -

pre-ISO performance)
A8.2.3.1.2. Engine trim position “A” (trim - - - -
box)
A8.2.3.1.3. Engine trim position “B” (left - - - -
seat)/trim supervisor
A8.2.3.1.4. Perform ground observer/position - - - -
“C” duties during engine run
A8.2.3.1.5. Engine trim position “D” (trim - - - -
evaluator)/performance
evaluation
A8.2.3.1.6. Deactivate/Activate Thrust - - - -
Reversers
A8.2.3.1.7. Fan trim balance - - - -
A8.2.3.1.8. Perform distribution system - - - -
operational check (audible)
A8.2.3.1.9. Install, operate, and remove trim - - - -
equipment
A8.3. SMALL GAS TURBINE (SGT)
ENGINES, AUXILIARY
POWER UNITS (APU)
OPERATING PRINCIPLES
TR: Applicable engine TOs
(A2.22.)
A8.3.1. Service/adjust

A8.3.1.1. Auxiliary Power Unit (APU) - - - -

A8.3.1.2. Oil system - - - -
A8.3.1.3. Fuel system - - - -
A8.3.1.4. Electrical system - - - -
A8.3.1.5. Pneumatic system - - - -

Attachment 8
89
 CF6-50 (KC-10)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A8.3.1.6. Enclosure - - - -
A8.3.1.7. Inlet door and actuation system - - - -
A8.3.1.8. Perform APU/QSAS checks - - - -
(including pre-ISO)
A8.3.2. Remove/install

A8.3.2.1. APU/QSAS

A8.3.2.1.1. Remove - - - -
A8.3.2.1.2. Install - - - -
A8.3.2.2. Generator

A8.3.2.2.1. Remove - - - -
A8.3.2.2.2. Install - - - -
A8.3.2.3. Fuel control

A8.3.2.3.1. Remove - - - -
A8.3.2.3.2. Install - - - -
A8.3.2.4. Fuel filter element

A8.3.2.4.1. Remove - - - -
A8.3.2.4.2. Install - - - -
A8.3.2.5. Fuel nozzle assembly

A8.3.2.5.1. Remove - - - -
A8.3.2.5.2. Install - - - -
A8.3.2.6. Start/servo fuel solenoid valve

A8.3.2.6.1. Remove - - - -
A8.3.2.6.2. Install - - - -
A8.3.2.7. Oil temperature/pressure switch

A8.3.2.7.1. Remove - - - -
A8.3.2.7.2. Install - - - -
A8.3.2.8. Oil filter element

Attachment 8
90
 CF6-50 (KC-10)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A8.3.2.8.1. Remove - - - -
A8.3.2.8.2. Install - - - -
A8.3.2.9. Pneumatic ducting

A8.3.2.9.1. Remove - - - -
A8.3.2.9.2. Install - - - -
A8.3.2.10. Pneumatic control valve(s)

A8.3.2.10.1. Remove - - - -
A8.3.2.10.2. Install - - - -
A8.3.2.11. EGT thermocouple

A8.3.2.11.1. Remove - - - -
A8.3.2.11.2. Install - - - -
A8.3.2.12. Ignition exciter

A8.3.2.12.1. Remove - - - -
A8.3.2.12.2. Install - - - -
A8.3.2.13. Air inlet doors

A8.3.2.13.1. Remove - - - -
A8.3.2.13.2. Install - - - -
A8.3.2.14. Inlet door actuator

A8.3.2.14.1. Remove - - - -
A8.3.2.14.2. Install - - - -
A8.3.2.15. Starter/clutch/paw carrier

A8.3.2.15.1. Remove - - - -
A8.3.2.15.2. Install - - - -
A8.3.2.16. Oil pump

A8.3.2.16.1. Remove - - - -
A8.3.2.16.2. Install - - - -

Attachment 8
91
 CF6-50 (KC-10)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A8.3.2.17. Combustion case drain valve

A8.3.2.17.1. Remove - - - -
A8.3.2.17.2. Install - - - -
A8.3.2.18. Electronic control unit/voltage
regulator/four speed box
A8.3.2.18.1. Remove - - - -
A8.3.2.18.2. Install - - - -
A8.3.2.19. Cooling fan assembly

A8.3.2.19.1. Remove - - - -
A8.3.2.19.2. Install - - - -
A8.3.2.20. Oil temperature regulator (oil
cooler)
A8.3.2.20.1. Remove - - - -
A8.3.2.20.2. Install - - - -
A8.3.2.21. Electronic control unit operation

A8.3.2.21.1. Remove - - - -
A8.3.2.21.2. Install - - - -
A8.3.2.22. Exciter box

A8.3.2.22.1. Remove - - - -
A8.3.2.22.2. Install - - - -

Attachment 8
92
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 9

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on F117 (C-17) engines.

A9.1. ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-5-14, 00-20 series,
and applicable aircraft/engine
TOs (A2.15.)
A9.1.1. Perform inspections

A9.1.1.1. Inlet and exhaust *

- - - -
A9.1.1.2. Special inspections (Over speed, *
over temperature, etc) - - - -
A9.1.1.3. Fan exit fairing
- - - -
A9.1.1.4. Home station check
- - - -
A9.1.1.5. Clean gas turbine aircraft engines
and associated parts - - - -
TR: TO 2J-1-13
A9.1.1.6. Operate, input/retrieve/interpret
data from turbine/engine - - - -
monitoring system/MADARS
(Operate caution, warning and
malfunction display, etc.)
A9.1.1.7. Fuselage/wing access entry
- - - -
A9.1.1.8. Fuselage wing/access exit
- - - -
A9.1.1.9. Connect/disconnect exit
pneumatic air - - - -
A9.1.2. Operate

A9.1.2.1. Flaps/slats system

TR: TO 27JG-50-1 - - - -
A9.1.2.2. Multifunction Display System
(MFD) - - - -
A9.1.2.3. Visual Warning and Caution
System - - - -
A9.1.2.4. Mission Computer
- - - -
A9.1.2.5. Maintenance Monitor Panel to
View and Erase Faults - - - -
A9.2. ENGINE MAINTENANCE
TR: TOs 00-20-1, 00-35D-54,
1-1A-8, 2J-1-13, 2-1-111, and
applicable aircraft/engine TOs
(A4.3.)
A9.2.1. Perform preliminary maintenance
procedures
A9.2.1.1. Auxiliary Power Unit (APU)
- - - -

Attachment 10
93
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.2. Perform maintenance functions

A9.2.2.1. Install Engine water wash

equipment - - - -
A9.2.3. Cowl door support rods

A9.2.3.1. Remove
- - - -
A9.2.3.2. Install
- - - -
A9.2.4. Remove and install engine
system components
A9.2.4.1. Cowl ice protection shut-off
valve
A9.2.4.1.1. Remove
- - - -
A9.2.4.1.2. Inspect/Repair
- - - -
A9.2.4.1.3. Install
- - - -
A9.2.4.2. Cowl ice detector

A9.2.4.2.1. Remove
- - - -
A9.2.4.2.2. Inspect/Repair
- - - -
A9.2.4.2.3. Install
- - - -
A9.2.4.2.4. Operational Check
- - - -
A9.2.4.3. Engine cowl A/I venturi duct

A9.2.4.3.1. Remove
- - - -
A9.2.4.3.2. Inspect/Repair
- - - -
A9.2.4.3.3. Install
- - - -
A9.2.4.4. Fan thrust reverser actuator

A9.2.4.4.1. Remove
- - - -
A9.2.4.4.2. Inspect/Repair
- - - -
A9.2.4.4.3. Install
- - - -
A9.2.4.5. Core thrust reverser actuator

A9.2.4.5.1. Remove
- - - -
A9.2.4.5.2. Inspect/Repair
- - - -

Attachment 10
94
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.5.3. Install
- - - -
A9.2.4.6. Fan blocker door

A9.2.4.6.1. Remove
- - - -
A9.2.4.6.2. Inspect/Repair
- - - -
A9.2.4.6.3. Install
- - - -
A9.2.4.7. Core blocker door

A9.2.4.7.1. Remove
- - - -
A9.2.4.7.2. Inspect/Repair
- - - -
A9.2.4.7.3. Install
- - - -
A9.2.4.8. Fan translating cowl

A9.2.4.8.1. Remove
- - - -
A9.2.4.8.2 Inspect/Repair
- - - -
A9.2.4.8.3. Install
- - - -
A9.2.4.9. Core translating cowl

A9.2.4.9.1. Remove
- - - -
A9.2.4.9.2. Inspect/Repair
- - - -
A9.2.4.9.3. Install
- - - -
A9.2.4.10. Core thrust reverser

A9.2.4.10.1. Remove
- - - -
A9.2.4.10.2. Inspect/Repair
- - - -
A9.2.4.10.3. Install
- - - -
A9.2.4.11. Core thrust reverser blocker door
link
A9.2.4.11.1. Remove
- - - -
A9.2.4.11.2. Inspect/Repair
- - - -
A9.2.4.11.3. Install
- - - -
A9.2.4.12. Sinc cables

Attachment 10
95
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.12.1. Remove
- - - -
A9.2.4.12.2. Inspect/Repair
- - - -
A9.2.4.12.3. Install
- - - -
A9.2.4.13. Fan duct opening actuating
cylinder
TR: TO 78JG-30-1
A9.2.4.13.1. Remove
- - - -
A9.2.4.13.2. Inspect/Repair
- - - -
A9.2.4.13.3. Install
- - - -
A9.2.4.14. Thrust reverser control valve

A9.2.4.14.1. Remove
- - - -
A9.2.4.14.2. Inspect/Repair
- - - -
A9.2.4.14.3. Install
- - - -
A9.2.4.15. Fan thrust reverser actuator
proximity sensor
TR: TO 78JG-3-1
A9.2.4.15.1. Remove
- - - -
A9.2.4.15.2. Inspect/Repair
- - - -
A9.2.4.15.3. Install
- - - -
A9.2.4.16. Fan TR proximity sensor

A9.2.4.16.1. Remove
- - - -
A9.2.4.16.2. Inspect/Repair
- - - -
A9.2.4.16.3. Install
- - - -
A9.2.4.17. Core TR upper actuator
proximity sensor
A9.2.4.17.1. Remove
- - - -
A9.2.4.17.2. Inspect/Repair
- - - -
A9.2.4.17.3. Install
- - - -
A9.2.4.18. Oil tank pressurization valve

A9.2.4.18.1. Remove
- - - -
A9.2.4.18.2. Inspect/Repair
- - - -

Attachment 10
96
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.18.3. Install
- - - -
A9.2.4.19. Fuel distribution valve

A9.2.4.19.1. Remove
- - - -
A9.2.4.19.2. Inspect/Repair
- - - -
A9.2.4.19.3. Install
- - - -
A9.2.4.20. Fuel/oil heat exchanger bypass
valve
A9.2.4.20.1. Remove
- - - -
A9.2.4.20.2. Inspect/Repair
- - - -
A9.2.4.20.3. Install
- - - -
A9.2.4.21. Main air/oil cooler

A9.2.4.21.1. Remove
- - - -
A9.2.4.21.2. Inspect/Repair
- - - -
A9.2.4.21.3. Install
- - - -
A9.2.4.22. Forward/aft cowl door

A9.2.4.22.1. Remove
- - - -
A9.2.4.22.2. Inspect/Repair
- - - -
A9.2.4.22.3. Install
- - - -
A9.2.4.23. Accessory doors
TR: TO 54JG-10-1
A9.2.4.23.1. Remove
- - - -
A9.2.4.23.2. Inspect/Repair
- - - -
A9.2.4.23.3. Install
- - - -
A9.2.4.23.4. Open/close
- - - -
A9.2.4.24. Nacelle latches

A9.2.4.24.1. Remove
- - - -
A9.2.4.24.2. Inspect/Repair
- - - -
A9.2.4.24.3. Install
- - - -

Attachment 10
97
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.25. High pressure turbine
thermocouple
A9.2.4.25.1. Remove
- - - -
A9.2.4.25.2. Inspect/Repair
- - - -
A9.2.4.25.3. Install
- - - -
A9.2.4.26. Forward/aft segment

A9.2.4.26.1. Remove
- - - -
A9.2.4.26.2. Inspect/Repair
- - - -
A9.2.4.26.3. Install
- - - -
A9.2.4.27. Fuel filter differential pressure
switch
A9.2.4.27.1. Remove
- - - -
A9.2.4.27.2. Inspect/Repair
- - - -
A9.2.4.27.3. Install
- - - -
A9.2.4.28. Engine fuel distribution valve
filter
A9.2.4.28.1. Remove
- - - -
A9.2.4.28.2. Inspect/Repair
- - - -
A9.2.4.28.3. Install
- - - -
A9.2.4.29. Fuel control unit filter

A9.2.4.29.1. Remove
- - - -
A9.2.4.29.2. Inspect/Repair
- - - -
A9.2.4.29.3. Install
- - - -
A9.2.4.30. Fuel inlet low pressure switch

A9.2.4.30.1. Remove
- - - -
A9.2.4.30.2. Inspect/Repair
- - - -
A9.2.4.30.3. Install
- - - -
A9.2.4.31. Fuel distribution valve filter

A9.2.4.31.1. Remove
- - - -

Attachment 10
98
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.31.2. Inspect/Repair
- - - -
A9.2.4.31.3. Install
- - - -
A9.2.4.32. Engine de-oiler

A9.2.4.32.1. Remove
- - - -
A9.2.4.32.2. Inspect/Repair
- - - -
A9.2.4.32.3. Install
- - - -
A9.2.4.33. Acoustic panels

A9.2.4.33.1. Remove
- - - -
A9.2.4.33.2. Inspect/Repair
- - - -
A9.2.4.33.3. Install
- - - -
A9.2.4.34. Compressor stator cylinder

A9.2.4.34.1. Remove
- - - -
A9.2.4.34.2. Inspect/Repair
- - - -
A9.2.4.34.3. Install
- - - -
A9.2.4.35. 14th stage bleed converter valve

A9.2.4.35.1. Remove
- - - -
A9.2.4.35.2. Inspect/Repair
- - - -
A9.2.4.35.3. Install
- - - -
A9.2.4.36. Starting (14th stage) bleed valve

A9.2.4.36.1. Remove
- - - -
A9.2.4.36.2. Inspect/Repair
- - - -
A9.2.4.36.3. Install
- - - -
A9.2.4.37. 2.5 bleed valve

A9.2.4.37.1. Remove
- - - -
A9.2.4.37.2. Inspect/Repair
- - - -
A9.2.4.37.3. Install
- - - -

Attachment 10
99
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.38. ACC cooling air valves

A9.2.4.38.1. Remove
- - - -
A9.2.4.38.2. Inspect/Repair
- - - -
A9.2.4.38.3. Install
- - - -
A9.2.4.39. Air/oil cooling air shutoff valve

A9.2.4.39.1. Remove
- - - -
A9.2.4.39.2. Inspect/Repair
- - - -
A9.2.4.39.3. Install
- - - -
A9.2.4.40. Fuel/oil heat exchanger solenoid

A9.2.4.40.1. Remove
- - - -
A9.2.4.40.2. Inspect/Repair
- - - -
A9.2.4.40.3. Install
- - - -
A9.2.4.41. #4 bearing scavenge valve

A9.2.4.41.1. Remove
- - - -
A9.2.4.41.2. Inspect/Repair
- - - -
A9.2.4.41.3. Install
- - - -
A9.2.4.42. V-groove (V-Band) latch
assembly
A9.2.4.42.1. Remove
- - - -
A9.2.4.42.2. Inspect/Repair
- - - -
A9.2.4.42.3. Install
- - - -
A9.2.4.42.4. Adjust
TR: TO 78JG-30-1 - - - -
A9.2.4.43. Load sharing latches

A9.2.4.43.1. Remove
- - - -
A9.2.4.43.2. Inspect/Repair
- - - -
A9.2.4.43.3. Install
- - - -
A9.2.4.44. 95% deployed proximity sensors

Attachment 10
100
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.44.1. Remove
- - - -
A9.2.4.44.2. Inspect/Repair
- - - -
A9.2.4.44.3. Install
- - - -
A9.2.4.45. Fuel injector and support
assembly
A9.2.4.45.1. Remove
- - - -
A9.2.4.45.2. Inspect/Repair
- - - -
A9.2.4.45.3. Install
- - - -
A9.2.4.46. Burner immersion thermocouple
(T3.5)
A9.2.4.46.1. Remove
- - - -
A9.2.4.46.2. Inspect/Repair
- - - -
A9.2.4.46.3. Install
- - - -
A9.2.4.47. Gearbox scavenge oil pump

A9.2.4.47.1. Remove
- - - -
A9.2.4.47.2. Inspect/Repair
- - - -
A9.2.4.47.3. Install
- - - -
A9.2.4.48. Fwd/aft cone segment

A9.2.4.48.1. Remove
- - - -
A9.2.4.48.2. Inspect/Repair
- - - -
A9.2.4.48.3. Install
- - - -
A9.2.4.49. Electronic engine control (EEC)

A9.2.4.49.1. Remove
- - - -
A9.2.4.49.2. Inspect/Repair
- - - -
A9.2.4.49.3. Install
- - - -
A9.2.4.50. EEC programming plug
connector assembly
A9.2.4.50.1. Remove
- - - -
A9.2.4.50.2. Inspect/Repair
- - - -

Attachment 10
101
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.50.3. Install
- - - -
A9.2.4.51. EEC alternator stator

A9.2.4.51.1. Remove
- - - -
A9.2.4.51.2. Inspect/Repair
- - - -
A9.2.4.51.3. Install
- - - -
A9.2.4.52. EEC alternator rotor

A9.2.4.52.1. Remove
- - - -
A9.2.4.52.2. Inspect/Repair
- - - -
A9.2.4.52.3. Install
- - - -
A9.2.4.53. EEC N1 speed motional pickup
transducer
A9.2.4.53.1. Remove
- - - -
A9.2.4.53.2. Inspect/Repair
- - - -
A9.2.4.53.3. Install
- - - -
A9.2.4.54. EEC inlet total
pressure/temperature probe
(TT2/PT2)
A9.2.4.54.1. Remove
- - - -
A9.2.4.54.2. Inspect/Repair
- - - -
A9.2.4.54.3. Install
- - - -
A9.2.4.55. EEC oil cooler fuel temperature
probe
A9.2.4.55.1. Remove
- - - -
A9.2.4.55.2. Inspect/Repair
- - - -
A9.2.4.55.3. Install
- - - -
A9.2.4.56. EEC oil cooler oil temperature
probe
A9.2.4.56.1. Remove
- - - -
A9.2.4.56.2. Inspect/Repair
- - - -
A9.2.4.56.3. Install
- - - -
A9.2.4.57. EEC front wiring harness (W2)

Attachment 10
102
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.2.4.57.1. Remove
- - - -
A9.2.4.57.2. Inspect/Repair
- - - -
A9.2.4.57.3. Install
- - - -
A9.2.4.58. EEC rear wiring harness (W1)

A9.2.4.58.1. Remove
- - - -
A9.2.4.58.2. Inspect/Repair
- - - -
A9.2.4.58.3. Install
- - - -
A9.2.4.59. EEC exhaust gas temperature
wiring harness (W31)
A9.2.4.59.1. Remove
- - - -
A9.2.4.59.2. Inspect/Repair
- - - -
A9.2.4.59.3. Install
- - - -
A9.2.4.60. EEC core wiring harness (W34)

A9.2.4.60.1. Remove
- - - -
A9.2.4.60.2. Inspect/Repair
- - - -
A9.2.4.60.3. Install
- - - -
A9.2.4.60.4. Perform EEC system operational
checkout - - - -
TR: TO 73JG-20-1
A9.3. ENGINE RIGGING
TR: Applicable aircraft/engine
TOs (A2.18.)
A9.3.1. Rig thrust reverser/proximity
sensors - - - -
A9.3.2. High pressure compressor
variable stator vanes - - - -
A9.4. AIRCRAFT INSTALLED
ENGINE TESTING
TR: Applicable aircraft/engine
TOs (A2.20.)
A9.4.1. Troubleshoot powerplant using FI
manual - - - -
TR: TO 71FI-00-1
A9.4.2. Perform fan blade clearance
check - - - -
TR: TO 70GS-00-1
A9.4.3. Operate maintenance interphone
system - - - -
A9.4.4. Operate UHF system
- - - -

Attachment 10
103
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.4.5. Perform engine operation

A9.4.5.1. Engine operation position “A”

- - - -
A9.4.5.2. Engine operation position “B”
- - - -
A9.4.5.3 Perform ground observer/position
“C” duties during engine run - - - -
A9.4.5.4. Deactivate/Activate Thrust
Reversers - - - -
A9.4.5.5. Open and close fan thrust
reverser duct assembly - - - -
TR: TO 78JG-30-1
A9.4.5.6. Hydraulically deploy and stow
thrust reversers - - - -
TR: TO 78JG-30-1
A9.4.5.7. Manually deploy and stow fan
thrust reverser - - - -
A9.4.5.8. Fan trim balance
- - - -
A9.4.5.9. Perform distribution system
operational check (audible) - - - -
A9.4.5.10. Adjust engine oil pressure
- - - -
A9.5. AUXILIARY POWER UNITS
(APU) OPERATING
PRINCIPLES GTCP
TR: Applicable engine TOs
(A2.22.)
A9.5.1. Service/adjust

A9.5.2. Preserve APU

- - - -
A9.5.3. Oil system
- - - -
A9.5.4. Adjust inlet door and actuation
system - - - -
A9.5.5. APU inlet door and actuation
system operational checkout - - - -
TR: TO 49JG-10-1
A9.5.6. Remove/install

A9.5.6.1. APU

A9.5.6.1.1. Remove
- - - -
A9.5.6.1.2. Install
- - - -
A9.5.6.2. APU access doors

A9.5.6.2.1. Remove
- - - -
A9.5.6.2.2. Install
- - - -

Attachment 10
104
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.5.6.3. APU mount link

A9.5.6.3.1. Remove
- - - -
A9.5.6.3.2. Install
- - - -
A9.5.6.4. APU start and control panel
TR: TO 49JG-60-1
A9.5.6.4.1. Remove
- - - -
A9.5.6.4.2. Install
- - - -
A9.5.6.5. APU generator scavenge
magnetic drain plug
TR: TO 49JG-90-1
A9.5.6.5.1. Remove
- - - -
A9.5.6.5.2. Install
- - - -
A9.5.6.6. Generator

A9.5.6.6.1. Remove
- - - -
A9.5.6.6.2. Install
- - - -
A9.5.6.7. Fuel control

A9.5.6.7.1. Remove
- - - -
A9.5.6.7.2. Install
- - - -
A9.5.6.8. Fuel control filter

A9.5.6.8.1. Remove
- - - -
A9.5.6.8.2. Install
- - - -
A9.5.6.9. APU fuel control filter
differential pressure switch
TR: TO 49JG-30-1
A9.5.6.9.1. Remove
- - - -
A9.5.6.9.2. Install
- - - -
A9.5.6.10. Fuel filter element

A9.5.6.10.1. Remove
- - - -
A9.5.6.10.2. Install
- - - -
A9.5.6.11. Fuel nozzle assembly

A9.5.6.11.1. Remove
- - - -

Attachment 10
105
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.5.6.11.2. Install
- - - -
A9.5.6.12. APU primary fuel manifold
assembly
TR: TO 49JG-30-1
A9.5.6.12.1. Remove
- - - -
A9.5.6.12.2. Install
- - - -
A9.5.6.13. APU secondary fuel manifold
assembly
TR: TO 49JG-30-1
A9.5.6.13.1. Remove
- - - -
A9.5.6.13.2. Install
- - - -
A9.5.6.14. Start/servo fuel solenoid valve

A9.5.6.14.1. Remove
- - - -
A9.5.6.14.2. Install
- - - -
A9.5.6.15. Oil temperature/pressure switch

A9.5.6.15.1. Remove
- - - -
A9.5.6.15.2. Install
- - - -
A9.5.6.16. Oil filter element

A9.5.6.16.1. Remove
- - - -
A9.5.6.16.2. Install
- - - -
A9.5.6.17. APU oil temperature sensor
(temp bulb)
TR: TO 49JG-90-1
A9.5.6.17.1. Remove
- - - -
A9.5.6.17.2. Install
- - - -
A9.5.6.18. APU oil filter delta pressure
switch
TR: TO 49JG-90-1
A9.5.6.18.1. Remove
- - - -
A9.5.6.18.2. Install
- - - -
A9.5.6.19. APU oil liquid level gauge

A9.5.6.19.1. Remove
- - - -
A9.5.6.19.2. Install
- - - -

Attachment 10
106
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.5.6.20. APU oil level switch
TR: TO 49JG-90-1
A9.5.6.20.1. Remove
- - - -
A9.5.6.20.2. Install
- - - -
A9.5.6.21. APU de-oil solenoid valve
TR: TO 49JG-90-1
A9.5.6.21.1. Remove
- - - -
A9.5.6.21.2. Install
- - - -
A9.5.6.22. APU generator scavenge oil
pump
TR: TO 49JG-90-1
A9.5.6.22.1. Remove
- - - -
A9.5.6.22.2. Install
- - - -
A9.5.6.23. APU magnetic drain plug
assembly
TR: TO 49JG-90-1
A9.5.6.23.1. Remove
- - - -
A9.5.6.23.2. Install
- - - -
A9.5.6.24. APU oil filler cap and adapter
assembly
TR: TO 49JG-90-1
A9.5.6.24.1. Remove
- - - -
A9.5.6.24.2. Install
- - - -
A9.5.6.25. Pneumatic ducting

A9.5.6.25.1. Remove
- - - -
A9.5.6.25.2. Install
- - - -
A9.5.6.26. APU exhaust deflector
TR: TO JG-80-1
A9.5.6.26.1. Remove
- - - -
A9.5.6.26.2. Install
- - - -
A9.5.6.27. APU exhaust duct
TR: TO 49JG-80-1
A9.5.6.27.1. Remove
- - - -
A9.5.6.27.2. Install
- - - -
A9.5.6.28. APU T-duct assembly

Attachment 10
107
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.5.6.28.1. Remove
- - - -
A9.5.6.28.2. Install
- - - -
A9.5.6.29. 4 1/2" surge valve

A9.5.6.29.1. Remove
- - - -
A9.5.6.29.2. Install
- - - -
A9.5.6.30. 5" load valve

A9.5.6.30.1. Remove
- - - -
A9.5.6.30.2. Install
- - - -
A9.5.6.31. EGT thermocouple

A9.5.6.31.1. Remove
- - - -
A9.5.6.31.2. Install
- - - -
A9.5.6.32. Fire detector assembly

A9.5.6.32.1. Remove
- - - -
A9.5.6.32.2. Install
- - - -
A9.5.6.33. Ignition exciter

A9.5.6.33.1. Remove
- - - -
A9.5.6.33.2. Install
- - - -
A9.5.6.34. Igniter plug

A9.5.6.34.1. Remove
- - - -
A9.5.6.34.2. Install
- - - -
A9.5.6.35. Igniter lead

A9.5.6.35.1. Remove
- - - -
A9.5.6.35.2. Install
- - - -
A9.5.6.36. Air inlet doors

A9.5.6.36.1. Remove
- - - -
A9.5.6.36.2. Install
- - - -

Attachment 10
108
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.5.6.37. Inlet door actuator

A9.5.6.37.1. Remove
- - - -
A9.5.6.37.2. Install
- - - -
A9.5.6.38. APU inlet door open proximity
sensor
TR: TO 49JG-10-1
A9.5.6.38.1. Remove
- - - -
A9.5.6.38.2. Install
- - - -
A9.5.6.39. Starter clutch

A9.5.6.39.1. Remove
- - - -
A9.5.6.39.2. Install
- - - -
A9.5.6.40. Starter motor

A9.5.6.40.1. Remove
- - - -
A9.5.6.40.2. Install
- - - -
A9.5.6.41. Lube pump

A9.5.6.41.1. Remove
- - - -
A9.5.6.41.2. Install
- - - -
A9.5.6.42. Fuel flow divider valve assembly

A9.5.6.42.1. Remove
- - - -
A9.5.6.42.2. Install
- - - -
A9.5.6.43. Combustion case drain valve

A9.5.6.43.1. Remove
- - - -
A9.5.6.43.2. Install
- - - -
A9.5.6.44. Electronic control unit

A9.5.6.44.1. Remove
- - - -
A9.5.6.44.2. Install
- - - -
A9.5.6.45. APU inlet guide vane actuator
TR: TO 49JG-20-1
A9.5.6.45.1. Remove
- - - -

Attachment 10
109
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.5.6.45.2. Install
- - - -
A9.5.6.46. Cooling fan assembly

A9.5.6.46.1. Remove
- - - -
A9.5.6.46.2. Install
- - - -
A9.5.6.47. Inlet pressure (P2) sensor

A9.5.6.47.1. Remove
- - - -
A9.5.6.47.2. Install
- - - -
A9.5.6.48. Inlet temperature (T2) sensor

A9.5.6.48.1. Remove
- - - -
A9.5.6.48.2. Install
- - - -
A9.5.6.49. Motional transducer assembly

A9.5.6.49.1. Remove
- - - -
A9.5.6.49.2. Install
- - - -
A9.5.6.50. APU transducer assembly (surge
control pallet)
TR: TO 49JG-60-1
A9.5.6.50.1. Remove
- - - -
A9.5.6.50.2. Install
- - - -
A9.5.6.51. Oil temperature regulator (oil
cooler)
A9.5.6.51.1. Remove
- - - -
A9.5.6.51.2. Install
- - - -
A9.5.6.52. Generator filter pressure regulator
valve
A9.5.6.52.1. Remove
- - - -
A9.5.6.52.2. Install
- - - -
A9.5.6.53. Generator filter element
TR: TO 49JG-90-1
A9.5.6.53.1. Remove
- - - -
A9.5.6.53.2. Install
- - - -
A9.6. Electronic control unit operation
- - - -

Attachment 10
110
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A9.7. Power plant operation
- - - -

Attachment 10
111
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes
Tasks Used to Indicate
Training/Information
Provided (See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

Attachment 10
112
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002

2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate

Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 10

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on TF33 (C-141, KC-135E) engines.

A10.1. ENGINE INSPECTION AND

PREVENTIVE MAINTENANCE
TR: TOs 00-5-14, 00-20 series,
and applicable aircraft/engine
TOs (A2.15.)
A10.1.1. Perform inspections

A10.1.1.1. Inlet and exhaust

- - - -
A10.1.1.2. Special inspections (Overspeed,
over temperature, etc) - - - -
A10.1.1.3. Home station check
- - - -
A10.1.1.4. Isochronal (major/minor)
- - - -
A10.1.1.5. Clean gas turbine aircraft engines
and associated parts - - - -
TR: TO 2J-1-13
A10.1.1.6. Fuel filter differential pressure
checks - - - -
A10.2. ENGINE MAINTENANCE
TR: TOs 00-20-1, 00-35D-54,
1-1A-8, 2J-1-13, 2-1-111, and
applicable aircraft/engine TOs
(A4.3.)
A10.2.1. Perform maintenance functions

A10.2.1.1. Thermostatic/air regulator

A10.2.1.1.1. Remove
- - - -
A10.2.1.1.2. Inspect
- - - -
A10.2.1.1.3. Repair
- - - -
A10.2.1.1.4. Install
- - - -
A10.2.1.2. TR filter

A10.2.1.2.1. Remove
- - - -
A10.2.1.2.2. Inspect
- - - -
A10.2.1.2.3. Repair
- - - -
A10.2.1.2.4. Install
- - - -

Attachment 10
113
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.1.3. Fuel shutoff actuator

A10.2.1.3.1. Remove
- - - -
A10.2.1.3.2. Inspect
- - - -
A10.2.1.3.3. Install
- - - -
A10.2.1.4. Main air/oil cooler

A10.2.1.4.1. Remove
- - - -
A10.2.1.4.2. Inspect
- - - -
A10.2.1.4.3. Install
- - - -
A10.2.1.5. Forward/Aft/upper/lower cowl
door
A10.2.1.5.1. Remove
- - - -
A10.2.1.5.2. Inspect
- - - -
A10.2.1.5.3. Repair
- - - -
A10.2.1.5.4. Install
- - - -
A10.2.1.6. Front accessory cover

A10.2.1.6.1. Remove
- - - -
A10.2.1.6.2. Inspect
- - - -
A10.2.1.6.3. Repair
- - - -
A10.2.1.6.4. Install
- - - -
A10.2.1.7. N1 Tach generator/sensor

A10.2.1.7.1. Remove
- - - -
A10.2.1.7.2. Inspect
- - - -
A10.2.1.7.3. Install
- - - -
A10.2.1.8. N2 Tach generator/control
alternator
A10.2.1.8.1. Remove
- - - -
A10.2.1.8.2. Inspect
- - - -
A10.2.1.8.3. Install
- - - -
A10.2.1.9. Pneumatic fuel heater assembly

Attachment 10
114
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.1.9.1. Remove
- - - -
A10.2.1.9.2. Inspect
- - - -
A10.2.1.9.3. Repair
- - - -
A10.2.1.9.4. Install
- - - -
A10.2.1.10. Engine low fuel pressure switch

A10.2.1.10.1. Remove
- - - -
A10.2.1.10.2. Install
- - - -
A10.2.1.11. Pneumatic fuel heater shutoff
valve/actuator
A10.2.1.11.1. Remove
- - - -
A10.2.1.11.2. Install
- - - -
A10.2.1.12. Engine air/oil separator

A10.2.1.12.1. Remove
- - - -
A10.2.1.12.2. Install
- - - -
A10.2.2. ENGINE RIGGING
TR: Applicable aircraft/engine
TOs (A2.18.)
A10.2.2.1. Rig engine/aircraft throttle rod
assemblies - - - -
A10.2.3. AIRCRAFT INSTALLED
ENGINE TESTING
TR: Applicable aircraft/engine
TOs (A2.20.)
A10.2.3.1. Engine operation

A10.2.3.1.1. Perform engine run (including

pre-ISO performance) - - - -
A10.2.3.1.2. Engine trim position “A” (trim
box) - - - -
A10.2.3.1.3. Engine trim position “B” (left
seat)/trim supervisor - - - -
A10.2.3.1.4. Perform ground observer/position
“C” duties during engine run - - - -
A10.2.3.1.5. Engine trim position “D” (trim
evaluator)/performance - - - -
evaluation
A10.2.3.1.6. Deactivate/Activate Thrust
Reversers - - - -
A10.2.3.1.7. Perform distribution system
operational check (audible) - - - -
A10.2.3.1.8. Install, operate and remove trim
equipment - - - -

Attachment 10
115
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.4. SMALL GAS TURBINE (SGT)
ENGINES, AUXILIARY
POWER UNITS (APU), QUICK
START AUXILIARY POWER
SYSTEM (QSAS) OPERATING
PRINCIPLES
TR: Applicable engine TOs
(A2.22.)
A10.2.4.1. Service/adjust

A10.2.4.1.1. Oil system

- - - -
A10.2.4.1.2. Fuel system
- - - -
A10.2.4.1.3. Electrical system
- - - -
A10.2.4.1.4. Pneumatic system
- - - -
A10.2.4.1.5. Inlet door and actuation system
- - - -
A10.2.4.1.6. Perform APU/QSAS checks
(including pre-ISO) - - - -
A10.2.4.2. Remove/inspect/install

A10.2.4.2.1. APU/QSAS

A10.2.4.2.1.1. Remove
- - - -
A10.2.4.2.1.2. Inspect
- - - -
A10.2.4.2.1.3. Install
- - - -
A10.2.4.2.2. Generator

A10.2.4.2.2.1. Remove
- - - -
A10.2.4.2.2.2. Inspect
- - - -
A10.2.4.2.2.3. Install
- - - -
A10.2.4.2.3. Fuel control

A10.2.4.2.3.1. Remove
- - - -
A10.2.4.2.3.2. Inspect
- - - -
A10.2.4.2.3.3. Install
- - - -
A10.2.4.2.4. Fuel filter element

A10.2.4.2.4.1. Remove
- - - -
A10.2.4.2.4.2. Inspect
- - - -

Attachment 10
116
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.4.2.4.3. Install
- - - -
A10.2.4.2.5. Fuel nozzle assembly

A10.2.4.2.5.1. Remove
- - - -
A10.2.4.2.5.2. Inspect
- - - -
A10.2.4.2.5.3. Install
- - - -
A10.2.4.2.6. Start/servo fuel solenoid valve

A10.2.4.2.6.1. Remove
- - - -
A10.2.4.2.6.2. Inspect
- - - -
A10.2.4.2.6.3. Install
- - - -
A10.2.4.2.7. Oil temperature/pressure switch

A10.2.4.2.7.1. Remove
- - - -
A10.2.4.2.7.2. Inspect
- - - -
A10.2.4.2.7.3. Install
- - - -
A10.2.4.2.8. Oil filter element

A10.2.4.2.8.1. Remove
- - - -
A10.2.4.2.8.2. Inspect
- - - -
A10.2.4.2.8.3. Install
- - - -
A10.2.4.2.9. Pneumatic ducting

A10.2.4.2.9.1. Remove
- - - -
A10.2.4.2.9.2. Inspect
- - - -
A10.2.4.2.9.3. Install
- - - -
A10.2.4.2.10. Pneumatic control valve(s)

A10.2.4.2.10.1. Remove
- - - -
A10.2.4.2.10.2. Inspect
- - - -
A10.2.4.2.10.3. Install
- - - -
A10.2.4.2.11. EGT thermocouple

A10.2.4.2.11.1. Remove
- - - -

Attachment 10
117
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.4.2.11.2. Inspect
- - - -
A10.2.4.2.11.3. Install
- - - -
A10.2.4.2.12. Fire detector loop (upper/lower)

A10.2.4.2.12.1. Remove
- - - -
A10.2.4.2.12.2. Inspect
- - - -
A10.2.4.2.12.3. Install
- - - -
A10.2.4.2.13. Ignition exciter

A10.2.4.2.13.1. Remove
- - - -
A10.2.4.2.13.2. Inspect
- - - -
A10.2.4.2.13.3. Install
- - - -
A10.2.4.2.14. Air inlet doors

A10.2.4.2.14.1. Remove
- - - -
A10.2.4.2.14.2. Inspect
- - - -
A10.2.4.2.14.3. Install
- - - -
A10.2.4.2.15. Inlet door actuator

A10.2.4.2.15.1. Remove
- - - -
A10.2.4.2.15.2. Inspect
- - - -
A10.2.4.2.15.3. Install
- - - -
A10.2.4.2.16. Electrical harness and cannon
plugs
A10.2.4.2.16.1. Remove
- - - -
A10.2.4.2.16.2. Inspect
- - - -
A10.2.4.2.16.3. Install
- - - -
A10.2.4.2.17. Starter/clutch/paw carrier

A10.2.4.2.17.1. Remove
- - - -
A10.2.4.2.17.2. Inspect
- - - -
A10.2.4.2.17.3. Install
- - - -
A10.2.4.2.18. Oil pump

Attachment 10
118
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.4.2.18.1. Remove
- - - -
A10.2.4.2.18.2. Inspect
- - - -
A10.2.4.2.18.3. Install
- - - -
A10.2.4.2.19. Fuel flow divider valve assembly

A10.2.4.2.19.1. Remove
- - - -
A10.2.4.2.19.2. Inspect
- - - -
A10.2.4.2.19.3. Install
- - - -
A10.2.4.2.20. Combustion case drain valve

A10.2.4.2.20.1. Remove
- - - -
A10.2.4.2.20.2. Inspect
- - - -
A10.2.4.2.20.3. Install
- - - -
A10.2.4.2.21. Electronic control unit/voltage
regulator/four speed box
A10.2.4.2.21.1. Remove
- - - -
A10.2.4.2.21.2. Inspect
- - - -
A10.2.4.2.21.3. Install
- - - -
A10.2.4.2.22. Cooling fan assembly

A10.2.4.2.22.1. Remove
- - - -
A10.2.4.2.22.2. Inspect
- - - -
A10.2.4.2.22.3. Install
- - - -
A10.2.4.2.23. Inlet pressure (P2) sensor

A10.2.4.2.23.1. Remove
- - - -
A10.2.4.2.23.2. Inspect
- - - -
A10.2.4.2.23.3. Install
- - - -
A10.2.4.2.24. Inlet temperature (T2) sensor

A10.2.4.2.24.1. Remove
- - - -
A10.2.4.2.24.2. Inspect
- - - -
A10.2.4.2.24.3. Install
- - - -

Attachment 10
119
 TF33 (C-141, KC-135E)
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A10.2.4.2.25. Oil temperature regulator (oil
cooler)
A10.2.4.2.25.1. Remove
- - - -
A10.2.4.2.25.2. Inspect
- - - -
A10.2.4.2.25.3. Install
- - - -
A10.2.4.2.26. Generator filter pressure regulator
valve
A10.2.4.2.26.1. Remove
- - - -
A10.2.4.2.26.2. Inspect
- - - -
A10.2.4.2.26.3. Install
- - - -
A10.2.4.3. Power plant operation
- - - -

Attachment 10
120
121
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL

ATTACHMENT 11

NOTE: The tasks and knowledge listed in this attachment are performed by personnel performing maintenance on secondary power/APU units.

A11.1. F-15 Jet Fuel Starter (JFS)

TR: 2JA3-50-6 and Applicable
aircraft TOs
A11.1.1. JFS
A11.1.1.1. Remove - - - -
A11.1.1.2. Inspect - - - -
A11.1.1.3. Install - - - -
A11.1.2. JFS FUEL FILTER
A11.1.2.1. Remove - - - -
A11.1.2.2. Inspect - - - -
A11.1.2.3. Install - - - -
A11.1.3. JFS FUEL CONTROL
A11.1.3.1. Remove - - - -
A11.1.3.2. Inspect - - - -
A11.1.3.3. Install - - - -
A11.1.4. JFS IGNITION UNIT
A11.1.4.1. Remove - - - -
A11.1.4.2. Inspect - - - -
A11.1.4.3. Install - - - -
A11.1.5. JFS IGNITER PLUG
A11.1.5.1. Remove - - - -
A11.1.5.2. Inspect - - - -
A11.1.5.3. Install - - - -
A11.1.6. JFS GENERATOR CONTROL
UNIT
A11.1.6.1. Remove - - - -
A11.1.6.2. Inspect - - - -
A11.1.6.3. Install - - - -
A11.1.7. JFS ATOMIZER ASSEMBLY
A11.1.7.1. Remove - - - -
A11.1.7.2. Inspect - - - -
A11.1.7.3. Install - - - -

Attachment 11
122
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.1.8. JFS COMPRESSOR AIR INLET
DUCT
A11.1.8.1. Remove - - - -
A11.1.8.2. Inspect - - - -
A11.1.8.3. Install - - - -
A11.1.9. JFS AXIAL CONTAINMENT
RING
A11.1.9.1. Remove - - - -
A11.1.9.2. Inspect - - - -
A11.1.9.3. Install - - - -
A11.1.10. JFS TURBINE PLENUM
A11.1.10.1. Remove - - - -
A11.1.10.2. Inspect - - - -
A11.1.10.3. Install - - - -
A11.1.11. JFS POWER TURBINE
ASSEMBLY
A11.1.11.1. Remove - - - -
A11.1.11.2. Inspect - - - -
A11.1.11.3. Install - - - -
A11.1.12. JFS CARBON SEAL
A11.1.12.1. Remove - - - -
A11.1.12.2. Inspect - - - -
A11.1.12.3. Install - - - -
A11.1.13. JFS ANNULAR COMBUSTION
CHAMBER
A11.1.13.1. Remove - - - -
A11.1.13.2. Inspect - - - -
A11.1.13.3. Install - - - -
A11.2. F-15 CENTRAL GEAR BOX
(CGB)
TR: 2JA16-3-2 AND
APPLICABLE AIRCRAFT TO
A11.2.1. CGB
A11.2.1.1. Remove - - - -
A11.2.1.2. Inspect - - - -
A11.2.1.3. Install - - - -

Attachment 11
123
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.2.2. CGB INLET REVERSE DUCT
AND OIL COOLER FAN INLET
HOUSING
A11.2.2.1. Remove - - - -
A11.2.2.2. Inspect - - - -
A11.2.2.3. Install - - - -
A11.2.3. CGB CLUTCH AND BRAKE
ASSEMBLY
A11.2.3.1. Remove - - - -
A11.2.3.2. Inspect - - - -
A11.2.3.3. Install - - - -
A11.2.4. CGB HYDRAULIC STARTER
ASSEMBLY
A11.2.4.1. Remove - - - -
A11.2.4.2. Inspect - - - -
A11.2.4.3. Install - - - -
A11.2.5. CGB SWITCH AND OIL PUMP
ASSEMBLY
A11.2.5.1. Remove - - - -
A11.2.5.2. Inspect - - - -
A11.2.5.3. Install - - - -
A11.2.6. CGB LUBE SYSTEM
COMPONENTS
A11.2.6.1. Remove - - - -
A11.2.6.2. Inspect - - - -
A11.2.6.3. Install - - - -
A11.2.7. CGB ALTERNATING CURRENT
GENERATOR ASSEMBLY
(PMG)
A11.2.7.1. Remove - - - -
A11.2.7.2. Inspect - - - -
A11.2.7.3. Install - - - -
A11.2.8. CGB FAN ASSEMBLE AND FAN
STATOR
A11.2.8.1. Remove - - - -
A11.2.8.2. Inspect - - - -
A11.2.8.3. Install - - - -
A11.2.9. CGB CARBON SEAL
ASSEMBLY

Attachment 11
124
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.2.9.1. Remove - - - -
A11.2.9.2. Inspect - - - -
A11.2.9.3. Install - - - -
A11.2.10. CGB RATCHET WHEEL
ASSEMBLY, COUPLING STUB
SHAFT AND SEAL ASSEMBLY
A11.2.10.1. Remove - - - -
A11.2.10.2. Inspect - - - -
A11.2.10.3. Install - - - -
A11.2.11. CGB HYDRAULIC CLUTCH
CONTROL VALVE
A11.2.11.1. Remove - - - -
A11.2.11.2. Inspect - - - -
A11.2.11.3. Install - - - -
A11.3. F-15 AIRFRAME MOUNTED
ACCESSORY DRIVE (AMAD)
TR: 2JA16-3-2 AND
APPLICABLE AIRCRAFT TOS
A11.3.1. AMAD
A11.3.1.1. Remove - - - -
A11.3.1.2. Inspect - - - -
A11.3.1.3. Install - - - -
A11.3.2. AMAD POWER TAKEOFF
SHAFT SEAL ASSEMBLY
A11.3.2.1. Remove - - - -
A11.3.2.2. Inspect - - - -
A11.3.2.3. Install - - - -
A11.3.3. AMAD OIL PUMP AND
GOVERNOR ASSEMBLY (50%
SWITCH)
A11.3.3.1. Remove - - - -
A11.3.3.2. Inspect - - - -
A11.3.3.3. Install - - - -
A11.3.4. AMAD SHUTTLE
VALVEASSEMBLY
A11.3.4.1. Remove - - - -
A11.3.4.2. Inspect - - - -
A11.3.4.3. Install - - - -

Attachment 11
125
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.3.5. AMAD PLAIN ENCASE SEAL
ASSEMBLY
A11.3.5.1. Remove - - - -
A11.3.5.2. Inspect - - - -
A11.3.5.3. Install - - - -
A11.3.6. AMAD MAGNETIC SEAL
A11.3.6.1. Remove - - - -
A11.3.6.2. Inspect - - - -
A11.3.6.3. Install - - - -
A11.3.7. AMAD ISOLATION
DECOUPLER PAWL CARRIER
ASSEMBLY
A11.3.7.1. Remove - - - -
A11.3.7.2. Inspect - - - -
A11.3.7.3. Install - - - -
A11.3.8. AMAD DAMPING LAYSHAFT
ASSEMBLY
A11.3.8.1. Remove - - - -
A11.3.8.2. Inspect - - - -
A11.3.8.3. Install - - - -
A11.4. B-1 AUXILIARY POWER UNIT
(APU)
TR: 1B-1B-2-49JG-10-1 AND
APPLICABLE AIRCRAFT TOS
A11.4.1. APU
A11.4.1.1. Remove - - - -
A11.4.1.2. Inspect - - - -
A11.4.1.3. Install - - - -
A11.4.2. APU FUEL CONTROL
A11.4.2.1. Remove - - - -
A11.4.2.2. Inspect - - - -
A11.4.2.3. Install - - - -
A11.4.3. APU OIL PUMP
A11.4.3.1. Remove - - - -
A11.4.3.2. Inspect - - - -
A11.4.3.3. Install - - - -
A11.4.4. APU CLUTCH

Attachment 11
126
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.4.4.1. Remove - - - -
A11.4.4.2. Inspect - - - -
A11.4.4.3. Install - - - -
A11.4.5. APU FUEL OIL COOLER
A11.4.5.1. Remove - - - -
A11.4.5.2. Inspect - - - -
A11.4.5.3. Install - - - -
A11.4.6. APU LOAD CONTROL VALVE
A11.4.6.1. Remove - - - -
A11.4.6.2. Inspect - - - -
A11.4.6.3. Install - - - -
A11.4.7. APU SURGE CONTROL VALVE
A11.4.7.1. Remove - - - -
A11.4.7.2. Inspect - - - -
A11.4.7.3. Install - - - -
A11.4.8. APU CLUTCH
A11.4.8.1. Remove - - - -
A11.4.8.2. Inspect - - - -
A11.4.8.3. Install - - - -
A11.4.9. APU PERMANENT MAGNETIC
GENERATOR (PMG)
A11.4.9.1. Remove - - - -
A11.4.9.2. Inspect - - - -
A11.4.9.3. Install - - - -
A11.4.10. APU LOW OIL PRESSURE (LOP)
SENSOR
A11.4.10.1. Remove - - - -
A11.4.10.2. Inspect - - - -
A11.4.10.3. Install - - - -
A11.4.11. APU ELECTRONIC CONTROL
ASSEMBLY (ECA)
A11.4.11.1. Remove - - - -
A11.4.11.2. Inspect - - - -
A11.4.11.3. Install - - - -
A11.4.12. APU FUEL SOLENOID
SHUTOFF VALVE

Attachment 11
127
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.4.12.1. Remove - - - -
A11.4.12.2. Inspect - - - -
A11.4.12.3. Install - - - -
A11.4.13. APU FUEL FLOW DIVIDER
VALVE
A11.4.13.1. Remove - - - -
A11.4.13.2. Inspect - - - -
A11.4.13.3. Install - - - -
A11.4.14. APU FUEL FILTER ELEMENT
A11.4.14.1. Remove - - - -
A11.4.14.2. Inspect - - - -
A11.4.14.3. Install - - - -
A11.4.15. APU OIL FILTER ELEMENT
A11.4.15.1. Remove - - - -
A11.4.15.2. Inspect - - - -
A11.4.15.3. Install - - - -
A11.4.16. APU HYDRAULIC START
MOTOR
A11.4.16.1. Remove - - - -
A11.4.16.2. Inspect - - - -
A11.4.16.3. Install - - - -
A11.4.17. APU IGNITION UNIT
A11.4.17.1. Remove - - - -
A11.4.17.2. Inspect - - - -
A11.4.17.3. Install - - - -
A11.4.18. APU IGNITER PLUG
A11.4.18.1. Remove - - - -
A11.4.18.2. Inspect - - - -
A11.4.18.3. Install - - - -
A11.5. B1 Accessory Drive Gearbox
(ADG)
TR: 1B-1B-2-83JG-20-1 and
Applicable aircraft TOs
A11.5.1 ADG GEARBOX
A11.5.1.1. Remove - - - -
A11.5.1.2. Inspect - - - -
A11.5.1.3. Install - - - -

Attachment 11
128
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.5.2. ADG TORQUE CONVERTER
A11.5.2.1. Remove - - - -
A11.5.2.2. Inspect - - - -
A11.5.2.3. Install - - - -
A11.5.3. ADG HIGH OIL PRESSURE
PUMP
A11.5.3.1. Remove - - - -
A11.5.3.2. Inspect - - - -
A11.5.3.3. Install - - - -
A11.5.4. ADG LOW OIL PRESSURE
PUMP
A11.5.4.1. Remove - - - -
A11.5.4.2. Inspect - - - -
A11.5.4.3. Install - - - -
A11.5.5. ADG CLUTCH
A11.5.5.1. Remove - - - -
A11.5.5.2. Inspect - - - -
A11.5.3.3. ADG LOW OIL PRESSURE
PUMP
A11.5.3.3.1. Remove - - - -
A11.5.3.3.2. Inspect - - - -
A11.5.3.3.3. Install - - - -
A11.5.6. ADG CLUTCH
A11.5.6.1. Remove - - - -
A11.5.6.2. Inspect - - - -
A11.5.6.3. Install - - - -
A11.5.7. ADG LOW OIL PRESSURE
SENSOR
A11.5.7.1. Remove - - - -
A11.5.7.2. Inspect - - - -
A11.5.7.3. Install - - - -
A11.5.8. ADG HIGH OIL TEMPERATURE
SENSOR
A11.5.8.1. Remove - - - -
A11.5.8.2. Inspect - - - -
A11.5.8.3. Install - - - -
A11.5.9. ADG SPEED SENSOR

Attachment 11
129
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.5.9.1. Remove - - - -
A11.5.9.2. Inspect - - - -
A11.5.9.3. Install - - - -
A11.5.10. ADG THERMOSTATIC BYPASS
VALVE
A11.5.10.1. Remove - - - -
A11.5.10.2. Inspect - - - -
A11.5.10.3. Install - - - -
A11.5.11. ADG OIL FILTER ELEMENT
A11.5.11.1. Remove - - - -
A11.5.11.2. Inspect - - - -
A11.5.11.3. Install - - - -
A11.5.12. AGD GEARBOX PRESSURE
RELIEF VALVE
A11.5.12.1. Remove - - - -
A11.5.12.2. Inspect - - - -
A11.5.12.3. Install - - - -
A11.5.13. ADG PRESSURE REGULATOR
VALVE
A11.5.13.1. Remove - - - -
A11.5.13.2. Inspect - - - -
A11.5.13.3. Install - - - -
A11.5.14. AGD LUBE CONTROL
MODULE ASSEMBLY
A11.5.14.1. Remove - - - -
A11.5.14.2. Inspect - - - -
A11.5.14.3. Install - - - -
A11.5.15. ENGINE TO ADG PTO SHAFT
A11.5.15.1. Remove - - - -
A11.5.15.2. Inspect - - - -
A11.5.15.3. Install - - - -
A11.5.16. ENGINE TO AGD PTO SHAFT
SPEED SENSOR
A11.5.16.1. Remove - - - -
A11.5.16.2. Inspect - - - -
A11.5.16.3. Install - - - -
A11.5.17. APU TO ADG PTO SHAFT

Attachment 11
130
 SECONDARY POWER/APU ATTACHMENT
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used to Indicate
Tasks Training/Information Provided
(See Atch 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C D
3 Skill CDC 7 Skill Exportable
Level Level Course
5 7 Tng Tng Trainee Trainer Certifier 5 7
Start Comp Initials Initials Initials Course 5 7 Course LVL LVL
A11.5.17.1. Remove - - - -
A11.5.17.2. Inspect - - - -
A11.5.17.3. Install - - - -
A11.5.18. APU TO AGD PTO SHAFT
SPEED SENSOR
A11.5.18.1. Remove - - - -
A11.5.18.2. Inspect - - - -
A11.5.18.3. Install - - - -
A11.5.19. AIR TURBINE STARTER
A11.5.19.1. Remove - - - -
A11.5.19.2. Inspect - - - -
A11.5.10.3. Install - - - -
A11.5.20. AIR TURBINE STARTER
CONTROL VALVE
A11.5.20.1. Remove - - - -
A11.5.20.2. Inspect - - - -
A11.5.20.3. Install - - - -

Attachment 11
131
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC

ATTACHMENT 12

NOTE 1: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 2: This attachment is to be used in conjunction with other attachments in applicable CFETPs.
NOTE 3: This attachment is to be used as a correlation document for the 2AX7X 7-level Aerospace Maintenance Craftsman CDC’s.
NOTE 4: All items are SUBJECT KNOWLEDGE LEVELS only and require no certification on this attachment unless career knowledge
documentation is required for a 2-time CDC failure.
A12.1. MANAGEMENT WITHIN
THE MAINTENANCE
COMPLEX
TR: AFI 21-101, AFI 21-118
and specific MAJCOM
guidance

A12.1.2. Functions of the Maintenance - - - B

Complex

A12.1.3. Operations / Logistics Group - - - B

Commander Responsibilities
TR: AFI 38-101, AFPD 38-1

A12.1.4. Accountability and Core - - - B

Values

A12.1.5. Aircraft Maintenance - - - B

Management Information
Systems

A12.1.6. Maintenance Analysis - - - B

A12.1.7. Compliance and - - - A

Standardization Requirements
Listings

A12.1.8. Maintenance Quality - - - B

Performance Measures (QPM)
Relationships

A12.1.9. Health-of-the-Fleet Metrics - - - B

A12.1.10. Foreign Object Damage (FOD) - - - A

Program Manager
TR: AFI 21-101

A12.1.11. Joint Oil Analysis Program - - - B

TR: T.O. 33-1-37-1

A12.1.12. Mobility - - - A

A12.1.13. Hazard Declarations for - - - A

Mobility Packages
TR: AFMAN 24-204

Attachment 12
132
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.1.14. Hazardous Material Handling - - - B
Procedures
TR: AFJMAN 24-204, AFI 91-
301, AFI 24-202,
AFMAN 23-110

A12.1.15. Production Supervisor, Flight - - - B

Chief and Expediter Duties and
Responsibilities

A12.1.16. Special Certification Rosters - - - B

A12.1.17. Maintenance Incident - - - B

Investigation and Prevention
TR: AFI 91-204

A12.1.18. Aircraft Impoundment - - - A

TR: AFI 91-204

A12.1.19. Operational Risk Management - - - B

(ORM)
TR: AFPD 90-9, AFI 90-901,
AFPAM 90-902

A12.1.20. Restricted Maintenance Areas - - - A

A12.1.21. Force Protection - - - A

TR: AFDD 2-4.1

A12.1.22. Classification Info, Access to - - - B

Classified, COMSEC, OPSEC,
COMPUSEC
TR: AFI 33-211, AFI 10-1101,
AFI 33-202

A12.1.23. Proper Handling of Classified - - - A

Assets
TR: AFI 31-101

A12.1.24. Aircraft Inspection Concepts - - - B

TR: TO 00-20-5

A12.2. ENLISTED SPECIALTY

TRAINING
TR: AFI 36-2201 and
MAJCOM directives

A12.2.1. Training Management and - - - B

Records

A12.2.2. Automated Training Records - - - B

Attachment 12
133
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.2.3. Career Field Education and - - - B
Training Plan (CFETP)

A12.2.4. Specialty Training Standard - - - B

(STS)

A12.2.5. Occupational Survey Report - - - B

(OSR)

A12.2.6. Utilization and Training - - - B

Workshop (U&TW)

A12.2.7. Training Forecast / Request - - - A

A12.2.8. Training Waiver Process - - - B

A12.2.9. Field Evaluation Questionnaire - - - A

(FEQ) and Graduate
Assessment Survey

A12.3. ACCOUNTABILITY FOR

RECORDS, REPORTS, AND
FORMS
TR: AFI 21-109, TO 00-35D-
54, TO 00-20 Series and
applicable MAJCOM guidance

A12.3.1. Historical Records - - - B

A12.3.2. Minimum Essential - - - B

Configuration Management
(MESL)

A12.3.3. Automated Maintenance - - - A

Systems

A12.3.4. Reliability Availability, - - - A

Maintainability, Logistics
Engineering Support System
for Electronic Attack Pods and
Integrated Systems
(RAMPOD),
Core Automated Maintenance
System for Airlift (GO 81)

A12.3.5. Core Automated Maintenance - - - B

System (CAMS)
TR: AFM 66-279 Vol. I-
XXVII, T.O. 00-20-2

A12.3.6. Job Data Documentation (JDD) - - - B

Attachment 12
134
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.3.7. Air Force Technical Order - - - B
(AFTO) Forms 781 and 244 /
245

A12.3.8. Configuration Management - - - B

A12.3.9. Aircraft / Equipment - - - B

Modifications

A12.3.10. Nuclear Surety - - - B

TR: AFI 91-101

A12.3.11. Dull Sword Reporting - - - B

TR: AFI 91-204

A12.4. SUPPLY MANAGEMENT

TR: DOD 7200-10, AFM 67-1,
AFMAN 23-220, AFMAN 23-
110 and applicable MAJCOM
guidance

A12.4.1. Maintenance Supply Concept - - - B

TR: AFMAN 23-110

A12.4.2. Supply Documents - - - B

Management

A12.4.3. Precious Metal Program - - - A

TR: AFMAN 23-110

A12.4.4. Bench Stock - - - A

A12.4.5. Air Force Technical Order - - - A

(AFTO) 375

A12.4.6. Quick Reference List (QRL) - - - A

A12.4.7. Standard Base Supply System - - - B

(SBSS)
TR: AFMAN 23-110

A12.4.8. Integrated Logistic System- - - - A

Supply (ILS-S) and Global
Combat Support System
(GCSS)
TR: AFMAN 23-110

A12.4.9. Priority Systems - - - B

A12.4.10. Repair Cycle Assets - - - B

A12.4.11. Report of Survey, Statement of - - - B

Charges

Attachment 12
135
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.4.12. Equipment Account - - - B
Management

A12.4.13. Custodian - - - A
Authorization/Custody Receipt
Listing (CA/CRL)

A12.4.14. Precision Measurement - - - A

Equipment Laboratory (PMEL)

A12.4.15. Computer System Management - - - A

TR: AFI 33-112

A12.4.16. Special Purpose Recoverable - - - A

Authorized Maintenance
(SPRAM)
TR: AFMAN 23-110

A12.4.17. Air Force Management System - - - A

(AFEMS)

A12.4.18. Status of Resources and - - - A

Training (SORTS)

A12.4.19. Land Mobile Radios, Pagers, - - - A

Cell Phones
TR: AFI 33-106

A12.4.20. Shelf Life Program - - - A

TR: AFMAN 23-110

A12.4.21. Hazardous Materials - - - B

(HAZMAT)
TR: Applicable AFOSH
STD’s, AFI’s and MAJCOM
guidance

A12.4.22. Qualified Products Listing - - - B

A12.5. LOGISTICS AND

RESOURCE
MANAGEMENT
AFPD 21-1

A12.5.1. Logistics Management - - - B

A12.5.2. Agile Logistics - - - A

A12.5.3. Two-Level Maintenance (2LM) - - - A

A12.5.4. Execution and Prioritization of - - - A

Repair System (EXPRESS)

Attachment 12
136
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.5.5. Readiness Based Leveling - - - A
(RBL)
TR: AFMAN 23-110

A12.5.6. Resource Management - - - B

A12.5.7. Air Force Government-Wide - - - A

Purchase Card Program and
Air Force Form 9
TR: AFI 67-117

A12.5.8. Air Force Enhancement - - - A

Program (AFREP)
TR: AFI 21-123

A12.5.9. Financial Plan (FIN Plan) - - - A

A12.5.10. Appropriation (APPN) 3400 - - - A

and 3080 Budgeting

A12.5.11. Budget Line 3010 - - - A

A12.5.12. Air Force Materiel Command - - - A

(AFMC) Responsibilities

A12.5.13. Developmental Test and - - - A

Evaluation (DT&E)
Operational Test and
Evaluation (OT&E)

A12.5.14. Defense Logistics Agency - - - A

A12.5.15. Special Experience Identifier - - - B

(SEI)
TR: AFMAN 36-2108

A12.5.16. Unit Manpower Document - - - A

(UMD) and Unit Management
Personnel Roster (UMPR)

A12.5.17. Manning Standards, and - - - A

Logistics Composite Model
(LCOM)
TR: AFI 38-201,
AFMAN 38-208

A12.5.18. Technical Order Management - - - B

Attachment 12
137
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.5.19. Technical Order Distribution - - - A
Office (TODO),
Technical Order Distribution
Account (TODA),
Technical Order Distribution
Control Activity (TODCA),
Technical Order Review Board
(TORB)
TR: TO 00-5-1, TO 00-5-2

A12.5.20. Air Force Technical Order - - - A

Forms 22, 27, 110, 158

A12.5.21. Automated Technical Order - - - A

Management System (ATOMS)
TR: TO 00-5-2

A12.5.22. Time Compliance Technical - - - A

Orders (TCTO)
TR: TO 00-5-15

A12.5.23. Centralized Technical Order - - - A

Management Organization
(CTOM)
TR: TO 00-5-1
A12.5.24. Joint Computer –aided - - - A
Acquisition and Logistic
Support (JCALS)

A12.5.25. Electronic Technical Orders - - - A

A12.5.26. Deficiency Reporting - - - B

(Hardware and Software)
Product Quality Deficiency
Reporting System (PQDR),
TR: TO 00-35D-54

A12.5.27. Reporting of Deficiency (ROD) - - - B

A12.5.28. Bad Actor Program - - - A

TR: TO 00-20-1, TO 00-35D-
54

A12.5.29. Technical Improvement - - - A

Product Working Group
(TIPWG),
System Training Plan (STP),
Program Management Review
(PMR)

A12.5.30. Corrosion Prevention Advisory - - - A

Board (CPAB)
TR: AFI 21-105

Attachment 12
138
 2AX7X
CFETP 2A6X1A/C/D/E, August 2002
2. Core 3. Certification For OJT 4. Proficiency Codes Used To
Tasks Indicate Training/Information
Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B A B C D E A B C
3 Skill 5 Skill 7 Skill Level
Level Level
Tng Tng Trainee Trainer Certifier (1) (2)
5 7 Start Complete Initials Initials Initials Course CDC Course CDC
A12.6. COMPUTER APPLICATION

A12.6.1. Using Applications - - - B

A12.6.2. Form Flow - - - B

A12.6.3. Air Force Electronic Publishing - - - B

Library (AFEPL)

A12.6.4. World Wide Web (www), - - - B

Internet

A12.6.5. Local Area Networks (LAN) - - - B

Attachment 12
139
140
 CFETP 2A6X1A/C/D/E, January 2002
Section B - Course Objective List

4. Measurement. Each proficiency coded STS task or knowledge item taught at the technical
school is measured through the use of an objective. An objective is a written instruction for the
student so he or she knows what is expected of them to successfully complete training on each
task. Each objective is comprised of a condition, behavior, and standard which states what is
expected of the student for each task. The condition is the setting in which the training takes
place. The behavior is the action a student must demonstrate to accomplish a task (i.e. remove
and install wheel and tire assembly). The standard is the level of performance that is measured to
ensure the STS proficiency code level is attained. Each objective uses letter code(s) to identify
how it is measured. All objectives use the PC code which indicates a progress check is used to
measure subject or task knowledge. Progress checks are also used to measure student
accomplishment of performance objectives. W indicates a comprehensive written test and is
used to measure the subject and/or task knowledge at the end of a block of instruction. PC/W
indicates separate measurement of both knowledge and performance elements using a written test
and a performance progress check.

5. Standard. The standard is 70% on written examinations. Standards for performance

measurement are indicated in the objective and delineated on the individuals’ progress checklist.
The checklist is used by the instructor to document each students progress on each task.
Instructor assistance is provided as needed during the progress check, and students may be
required to repeat all or part of the behavior until satisfactory performance is attained. Students
must satisfactorily complete all PCs prior to taking the written test.

6. Proficiency Level. Most task performance is taught to the "2b" or "3c" proficiency level.
The "2b" means the student can do most parts of the task, but does need assistance on the hardest
parts of the task (partially proficient). The student can also determine step-by-step procedures for
doing the task. The "3c" means the student can do all parts of the task but may need a spot check
of completed work (competent). The student should be able to identify why and when the task
must be done and why each step is needed.

7. Course Objectives. If you require detailed course descriptions and objectives, please provide
a written request to the AETC Training Manager, 361 TRS/TRR, 501 Missile Road, Sheppard
AFB TX 76311-2264.

141
 CFETP 2A6X1A/C/D/E, January 2002

Section C - Support Material

8. The following list of support material is not all inclusive; however, it covers the most
frequently referenced areas. Support material is any training package designed to enhance the
learning process at any level of training. Refer to the Air Force Education and Training Course
Announcements (ETCA) for information on AETC formal courses.

8.1. The following Interactive Courseware (ICW) courses are available from or are under
development by 367 TRS/TRSS at Hill AFB, Utah. To obtain more information about each
course, request a copy of the Courseware Catalog from AETC/TRSS, 6058 Aspen, Building
1295, Hill AFB UT 84056-5805. Their FAX number is DSN 777-0897 and their customer
service number is DSN 777-0160. To request ordering information on hardware, your MAJCOM
training POC (for ACC, AMC, and ANG) is the first stop. For personnel under other
MAJCOMs, contact them directly; they will provide you the information required for purchasing
the item through them. If you decide to purchase the system, they will FAX you the AF Form
616 to use for an example. The 367 TRSS internet site is:
http://www.hill.af.mil/367TRSS/findex.htm.

COURSE NUMBER COURSE TITLE OPR

01JIV8931V5.1.1 B-1B APU Operation (CBT) 367 TRS/TRSS

01CPB4620R2 B-1B Engine Oil Analysis 367 TRS/TRSS

52CVT0413 B-52H Engine Inlet (VHS) 367 TRS/TRSS

15TIV23K1 F100 Ignition System Troubleshooting 367 TRS/TRSS

15AIV2400 F-15 Secondary Power System Troubleshooting 367 TRS/TRSS

and Maintenance

15AIV2401 F-15 Secondary Power System Advanced 367 TRS/TRSS

Troubleshooting

16AIV24D0 F-16C/D Engine Start System 367 TRS/TRSS

16AIV27G0 F-16C/D F110-GE-100 Engine Fuel and 367 TRS/TRSS

Control Advanced Troubleshooting

16GIV2304 F-16C/D F100-PW-220 Engine Fuel and 367 TRS/TRSS

Control Troubleshooting

142
 CFETP 2A6X1A/C/D/E, January 2002

COURSE NUMBER COURSE TITLE OPR

16TIV24D0 F-16C/D Block 50 Engine Start System 367 TRS/TRSS

Troubleshooting

00CVT0009 Torque Wrench Use and Care (VHS) 367 TRS/TRSS

00CIV0008 Type III Torque Wrench Use and Care (CBT) 367 TRS/TRSS

00TIV0001V1 Troubleshooting Techniques 367 TRS/TRSS

00TCB0002V1 Multimeter Familiarization 367 TRS/TRSS

8.2. The following training detachment courses are available from the 372 TRS and 373 TRS.
For more information on Fighter courses contact the 372 TRS, 912 I Avenue Suite 3, Sheppard
AFB TX 76311-2361, DSN 736-4801. For more information on Bomber/Cargo/Tanker courses
contact the 373 TRS, 912 I Avenue Suite 4, Sheppard AFB TX 76311-2362, DSN 736-4679.

COURSE NUMBER COURSE TITLE OPR

J4AMF/ASF/AST2A6X1A 000 F-15 Engine Start System (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 001 F100-PW-220/220E (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 002 F100-PW-220 372 TRS

J4AMF/ASF/AST2A6X1A 007 TR-1/U-2R, J75-13B Systems and 373 TRS

Troubleshooting

J4AMF/ASF/AST2A6X1A 010 U-2R Engine Operator 373 TRS

J4AMF/ASF/AST2A6X1A 015 KC-10, CF6-50 Systems 373 TRS

J4AMF/ASF/AST2A6X1A 016 KC-10, APU (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 017 F101 (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 018 F101 (I/M) 373 TRS

J4AMF/ASF/AST2A6X1A 019 F101 Engine Run Supervisor 373 TRS

143
 CFETP 2A6X1A/C/D/E, January 2002

COURSE NUMBER COURSE TITLE OPR

J4AMF/ASF/AST2A6X1A 023 B-52 Engine Operator 373 TRS

J4AMF/ASF/AST2A6X1A 025 EC/KC/RC/WC-135, J57 or TF33 Engine 373 TRS

Operation

J4AFM/ASF/AST2A6X1A 026 TF33-P-5/9/102 Familiarization 373 TRS

J4AMF/ASF/AST2A6X1A 028 KC-135R/T, F108 Engine Operator 373 TRS

J4AMF/ASF/AST2A6X1A 034 KC-135 Quick Start Auxiliary Power Unit 373 TRS
System

J4AMF/ASF/AST2A6X1A 035 F108-CF-100 (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 036 KC-135, T41M APU 373 TRS

J4AMF/ASF/AST2A6X1A 037 E-3, TF33-P-100A (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 038 GTCP165-1/1A (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 048 TF39 (I/M) 373 TRS

J4AMF/ASF/AST2A6X1A 049 C-5, GTCP165-1 (I/M) 373 TRS

J4AMF/ASF/AST2A6X1A 050 C-5, GTCP165-1 (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 056 A-10, TF34 (I/M) 373 TRS

J4AMF/ASF/AST2A6X1A 064 F110-GE-100 (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 065 F100-PW-100 (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 068 F110-GE-129 (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 070 F100-PW-229 (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 071 F100-PW-229 (I/M) 372 TRS

144
 CFETP 2A6X1A/C/D/E, January 2002

COURSE NUMBER COURSE TITLE OPR

J4AMF/ASF/AST2A6X1A 072 TF33 Depot Maintenance 373 TRS

J4AMF/ASF/AST2A6X1A 073 C-141, TF33 (I/M) 373 TRS

J4AMF/ASF/AST2A6X1A 074 APU/Engine (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 080 F118 Maint (APU, AMAD, Borescope, 373 TRS

Systems, and Component Maintenance)

J4AMF/ASF/AST2A6X1A 081 B-2 (F118) Engine Operator 373 TRS

J4AMF/ASF/AST2A6X1A 082 TF33-P-3 (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 086 F110-GE-129 Intermediate Differences 372 TRS

J4AMF/ASF/AST2A6X1A 089 F-117 Structural Tracking and Engine 373 TRS

Monitoring System

J4AMF/ASF/AST2A6X1A 090 F404 Engine (I/M) 372 TRS

J4AMF/ASF/AST2A6X1A 091 F404 Borescope and Blade Blending 372 TRS

Maintenance

J4AMF/ASF/AST2A6X1A 092 KC-135R, F108 Engine Trending and 373 TRS

Diagnostic

J4AMF/ASF/AST2A6X1A 093 EC/C-18, TF33-P102 Maintenance 373 TRS

J4AMF/ASF/AST2A6X1A 094 KC-135R Quick Start Auxiliary Power Unit 373 TRS
System Familiarization

J4AMF/ASF/AST2A6X1A 095 U-2S, F118-GE-101 Engine Familiarization 373 TRS

J4AMF/ASF/AST2A6X1A 096 U-2S, F118-GE-101 Engine Borescope 373 TRS

J4AMF/ASF/AST2A6X1A 097 U-2S, F118-GE-101 Engine Troubleshooting 373 TRS

J4AMF/ASF/AST2A6X1A 098 U-2S Engine Operator 373 TRS

145
 CFETP 2A6X1A/C/D/E, January 2002

COURSE NUMBER COURSE TITLE OPR

J4AMF/ASF/AST2A6X1A 099 Advanced Engine (O/M) 373 TRS

J4AMF/ASF/AST2A6X1A 100 Advanced APU 373 TRS

J4AMF/ASF/AST2A6X1A 101 F-16, F110 Engine Removal/Replacement 372 TRS

J4AMF/ASF/AST2A6X1A 102 F-16, F110-GE-129 Engine (O/M) 372 TRS

J4AMF/ASF/AST2A6X1A 103 F-16, F100-PW-220/220E Engine (O/M) 372 TRS

J4AMF/ASF/AST2A6X1A 104 F-16, F100-PW-229 Engine (O/M) 372 TRS

J4AMF/ASF/AST2A6X1A 105 F-16, F100-PW-229 Engine O/M Differences 372 TRS

J4AMF/ASF/AST2A6X1A 106 F-16, F110-GE-100 Engine (O/M) 372 TRS

J4AMF/ASF/AST2A6X1A 107 F-16, F100 Engine Removal/Replacement 372 TRS

Section D - Training Course Index

9. Purpose. This index lists Air Force resident, ECI, and exportable courses used to support
training for this specialty. Refer to the Air Force Education and Training Course
Announcements (ETCA) for information on AETC formal courses listed below.

9.1. Air Force In-Resident Courses:

COURSE NUMBER COURSE TITLE OPR

J3AQR2A611 001 Aerospace Propulsion Fundamentals 361 TRS

J3ABR2A631C 002 Aerospace Propulsion (TF33, TF34, F108) 361 TRS

J3ABR2A631D 007 Aerospace Propulsion (F-100) 361 TRS

J3ABR2A631E 006 Aerospace Propulsion (F-110) 361 TRS

J3AZR2A651A 006 Aerospace Propulsion (F110) (5-level) 361 TRS

J3ACR2A671A 003 Aerospace Propulsion Jet Engine Craftsman 361 TRS

146
 CFETP 2A6X1A/C/D/E, January 2002

9.2. Extension Course Institute (ECI) Courses:

COURSE NUMBER COURSE TITLE OPR

CDC 2A651A Aerospace Propulsion Jet Engine Journeyman 361 TRS

CDC 2AX7X Aerospace Maintenance Craftsman HQ USAF/ILMM

9.3. Exportable Courses.

COURSE NUMBER COURSE TITLE OPR MEDIA

***J6ANU2A6X1A 024 TF33-P-3/5 Engine Trim (CBT) 361 TRS CBT

***J6AGL2A6X1A 041 GTC85-106A Small Gas Turbine Engine 361 TRS CBT/VTT

J6ANU2E066-038 AF Technical Order System (General) 362 TRS CBT

J6ANU2E066-039 AF Technical Order System (Advanced) 362 TRS CBT

J6ANU00066-043 CAMS for Flightline and Backshop 362 TRS CBT

147
 CFETP 2A6X1A/C/D/E, January 2002

9.4. Courses Under Development/Revision:

COURSE NUMBER COURSE TITLE OPR

Section E - MAJCOM Unique Requirements.

10. Currently, only Air Combat Command has a MAJCOM mandatory course list (MMCL).
MAJCOMs change mandatory course requirements occasionally. Up-to-date ACC requirements
can be obtained at http://www.acclog.af.mil/lgq/lgqt/98mmcl.doc. Refer to the HQ ACC MMCL
for additional information.

COURSE AIRCRAFT COURSE TITLE

NUMBER

2A6X1A-056 A-10 TF-34 Engine Intermediate Maintenance

2A6X1A-017 B-1 Propulsion Technician (F-101 O/M)

2A6X1A-018 B-1 Propulsion Technician (F-101 I/M)

2A6X1A-080 B-2 B-2 Aerospace Propulsion – Jet Engine

2A6X1A-082 B-52 B-52 Aerospace Propulsion Craftsman (TF33)

2A6X1A-037 E-3B/C Jet Engine Specialist (TF33-P-100A)

2A6X1A-132 E-8C Jet Engine Technician

2A6X1A-026 EC/RC-135 Jet Engine Craftsman (TF-33/P-5/P-9/P-102) Familiarization

2A6X1A-134 KC-135 KC-135R Quick Start APU (QSAS) Tech (O/M)

2A6X1A-141 KC-135 KC-135R Quick Start APU (QSAS) Tech (T/S)

2A6X1A-035 KC-135 F108-CF-100 Jet Engine Craftsman

2A6X1A-092 KC-135 F108-CF-100 Engine Tending and Diagnostic

148
 CFETP 2A6X1A/C/D/E, January 2002

COURSE AIRCRAFT COURSE TITLE

NUMBER

2A6X1A-000 F-15/F-15E F-15 Engine Starting System

2A6X1A-136 F-15/F-15E F-15 Acft Eng Maint (F100-PW-220)

2A6X1A-065 F-15/F-15E Propulsion Tech (F100-PW-100/200) (I/M)

2A3X3A-110 F-15/F-15E F-15 Jet Eng Tech (F-100-PW-100) (O/M)

2A6X1A-144 F-16 F-16 Aircraft Prop Craftsman (F110-GE-100) (O/M)

2A6X1A-064 F-16 Propulsion Craftsman (F110-GE-100) (I/M)

2A6X1A-068 F-16 Propulsion Craftsman (F110-PW-129) (I/M)

2A6X1A-103 F-16 F-16 Aircraft Maint Tech (F100-PW-220-220E Eng)

2A6X1A-104 F-16 F-16 Aircraft Maint Tech (F-100-PW-229 Eng)

2A6X1A-105 F-16 F-16 Aircraft Maint Tech (F-100-PW-229) (Diff)

2A6X1A-090 F-117 F404 Jet Eng (I/M) (JEIM) Journeyman

2A6X1A-095 U-2 U-2S Engine Familiarization

149