VNM SIMULATION JSC
VNM CONFIGURATOR USER MANUAL
Contents
About us........................................................................................................................................2
I. Wheelbase Configuration.........................................................................................................3
II. Shifter Configuration..............................................................................................................3
2.1. LED Effects Customization...............................................................................................5
2.2. Calibrate the shifter...........................................................................................................6
2.2.1. Calibrate h-pattern.....................................................................................................6
2.2.2. Calibrate sequential....................................................................................................6
2.3. Set the shifter’s thresholds................................................................................................7
2.3.1. Set the h-pattern thresholds.......................................................................................7
2.3.2. Set the sequential thresholds......................................................................................8
2.4. Troubleshoot......................................................................................................................8
2.4.1. Cannot change the gear..............................................................................................8
2.5 Update firmware.................................................................................................................9
1
VNM SIMULATION JSC
About us
VNM Simulation JSC comes from Vietnam. We are a new simulation
equipment manufacture. We aim to deliver high simulation equipment and
help an active online DIY community where people can discuss how to
make high quality simulation equipment by themselves when using VNM
Simulation’s firmwares (these are free for personal use).
Download the lasted UI/Firmware on this repo:
https://github.com/hoantv/CarSimulatorFirmware
the repo includes:
Wheelbase firmware
Shifter firmware
UI
Will add pedal, handbrake, steering wheel soon.
2
VNM SIMULATION JSC
I. Wheelbase Configuration
Will be updated
II. Shifter Configuration
Connect the shifter via USB Type B to PC, the icon shifter will change
from orange to green. It indicates that the shifter is connected to PC. Go to
shifter Tab.
There is 2 options Analog Mode and Inversion Mode that are used for the
first setup before the shifter is packaged. So please don’t modify 2 option.
3
VNM SIMULATION JSC
Calibration Groupbox:
o H-Pattern/Sequential combobox: Based on position of a switch,
behind the shifter. The UI detect which mode is in use.
o Calibrate button: Usually, you don’t need this option, it is used
for the 1st setup of the shifter when uploading firmware or
factory reset. It used to set minimum, maximum of each shifter
axises (X, Y axis).
o The grid shows the gear area. When the shifter’s rod is in an
area, the number in this area will turn green. It indicates that a
gear change to this gear number.
o Three circles 9, 10, 11: Cycles 9,10 indicate the positions of the
truck’s knob button if use. The cycle 11 indicate switch mode
position.
Stats Groupbox
o Select Report combox: use for configuring the thresholds (X1,
X2, X3, Y1, Y2) for each shifter gear. It must in “Select
Report” to make the shifter work. “Shifter Configuration” is
used to configure the thresholds.
o FW: shows the version of shifter firmware.
o Min-Max: show min value, max value of X, Y axis after
calibration.
4
VNM SIMULATION JSC
Refesh button: Get the current shifter configuration
Factory Reset: To reset to default configuration.
Save: To save config to the shifter.
2.1. LED Effects Customization
Enable LED Effects: There are 10 effects for LED, 9 effects were fix
colors and Fade (custom) allow to change color. After changing this
option, please re-plug the shifter.
o Check: Enable LED Effects
o Uncheck: Disable LED Effects
Check / Uncheck each LED effect options to enable/disable each LED
effects.
Fade (custom): click to square button (1), a pop-up is display. You can
choose available colors in (2). To add new color by click to edit
button (3). In (4) you can click anywhere to choose a color that you
like and click add to add new color to the list more options. After
choosing a color, click OK button on popup.
After changing this option, please re-plug the shifter.
5
VNM SIMULATION JSC
When shifter reconnect, it will play new effects/color that you chose
before.
2.2. Calibrate the shifter
Note: Must calibration for each mode.
2.2.1. Calibrate h-pattern
It is uses to find the min-max value of X, Y axis. Only use at the 1st
time uploading firmware or click factory reset button.
o Step 1: put h-pattern plate onto the shifter.
o Step 2: click “calibrate” button, it will turn into “finish”, a
instruction popup is display, click “ok” button.
o Step 3: Switch the shifter to the top-most, bottom-most, left-
most, right-most. Do it several times.
o Step 4: Click “finish” when you’ve done.
o Step 5: click save to persist calibrate information to ROM
2.2.2. Calibrate sequential
It is uses to find the min-max value of Y axis. Only use at the 1st time
uploading firmware or click factory reset button.
o Step 1: put the sequential plate onto the shifter.
o Step 2: click “calibrate” button, it will turn into “finish”, a
instruction popup is display, click “ok” button.
6
VNM SIMULATION JSC
o Step 3: Switch the shifter to the top-most, bottom-most. Do it
several times.
o Step 4: Click “finish” when you’ve done.
o Step 5: click save to persist calibrate information to ROM
2.3. Set the shifter’s thresholds
2.3.1. Set the h-pattern thresholds
Step 1: Put the h-pattern plate to the shifter, switch to h-pattern mode.
Step 2: On select report combo box, choose Shifter configuration.
Step 3: click “display trails” to show the road of shifter’s position.
Step 4: move the shifter to each position. The trail display on the grid
like this.
Step 5: Drag/drop the vertical white lines such that when the shifter at
a position, The green pot doesn’t That point does not overlap white
lines.
7
VNM SIMULATION JSC
Step 6: Click save
Step 7: test again to make sure all gear position work.
2.3.2. Set the sequential thresholds
Step 1: Put the sequential plate to the shifter, switch to sequential
mode
Step 2: do like h-pattern setting with only 2 horizontal white lines
Step 3: Click save
Step 4: test again to make sure all gear position work.
2.4. Troubleshoot
when plug the shifter into PC, ensure “analog mode” is checked to
make the shifter work properly. If not, check it and save. Reconnect the
shifter.
2.4.1. Cannot change the gear
o Step 1: Ensure “Select Report” combox is default value (Select
Report)
8
VNM SIMULATION JSC
o Step 2: if “Select Report” combox is default value, change its
value to “shifter configuration”.
o Step 3: Check min-max value, min < 1000, max > 3500, if not
do calibration and set threshold again.
o Step 3: Moving the shifter’s rod to check the green pod
moving. Check when it stops at a gear, it overlaps white lines
or not. If it overlaps, adjust the lines’ position
o Step 4: if it still fails, capture the video and send us via email:
sale@vnmsimulation.com
2.5. Update firmware
Download update tool:
https://github.com/hoantv/CarSimulatorFirmware/tree/master/Update
%20tool
Download lastest firmware VNMShifter.hex in:
https://github.com/hoantv/CarSimulatorFirmware/tree/master/shifter
Connect USB A to USB A to usbA port has icon upgrade, remove usb
type B cable
Open tool after installing
Click connect icon, it connect to MCU of the shifter.
9
VNM SIMULATION JSC
Click “verify program” and browse to the VNMShifter.hex which was
downloaded.
10
VNM SIMULATION JSC
Click start to upload firmware
Remove usb A to usb A cable, connect USB B to PC. Open the GUI,
it displays the version equal to the version you have downloaded.
11
VNM SIMULATION JSC
Try the shifter, if having wrong gear when changing, do calibrate
(usually don’t need)
12
