1.
M60 / M60S Series
1.5 How to backup / recover /replace the NC unit
D. Operation procedure
The data is backed up and restored by using BACKUP screen .
Refer following procedure for details on operations.
1.5.1 BACKUP Screen
If the page key NEXT
PAGE is pressed on the SETUP screen, the BACK UP screen will open.
[OPEN BACKUP] PARAM 3. 2/2
Open the BACKUP screen?
YES : "Y" "INPUT"
NO : "N" "INPUT"
#( )
WORK PROCESS I/O PAR SETUP MENU
Input "Y" in the setting area # ( ), and press the INPUT key. The BACKUP screen will open.
[BACKUP] PARAM 3
Please execute "EMERGENCY STOP" before operation.
#1 BACKUP BACKUP INFORMATION
#2 RESTORE SAVE DATE 01/09/05 16:24
SER.NO. M6123456789
WORK PROCESS I/O PAR SETUP MENU
The date and time that the backup data was saved, and the serial No. are displayed on this screen.
48
1. M60 / M60S Series
1.5 How to backup / recover /replace the NC unit
1.5.1.1 Backup Operations
The parameters are backed up in the maintenance memory cassette with the following steps.
(1)
Execute emergency stop.
#( ) ( )
"EMG EMERGENCY" will appear at the EMG EMERGENCY
operation message area.
WORK PROCESS I/O PAR SETUP MENU
(2)
Input "1" at the setting area # ( ),
and press the INPUT key. #(1) ( ) PLC STOP Y/N
EMG EMERGENCY
"PLC STOP Y/N" will appear at the
WORK PROCESS I/O PAR SETUP MENU
message area.
(3)
Input "Y" at the setting area ( ),
and press the INPUT key. #(1) ( Y) BACKUP EXEC Y/N
EMG EMERGENCY
"BACKUP EXEC Y/N" will appear at the WORK PROCESS I/O PAR SETUP MENU
message area.
(4)
Input "Y" at the setting area ( ),
and press the INPUT key. #(1) ( Y) BACKUP EXECUTION
EMG EMERGENCY
(a) The message "BACKUP EXECUTION"
WORK PROCESS I/O PAR SETUP MENU
will appear while the parameters are
being backed up.
(b) The message "BACKUP COMPLETE"
will appear when backup is completed.
#( ) ( ) BACKUP COMPLETE
EMG EMERGENCY
WORK PROCESS I/O PAR SETUP MENU
Note 1 Other screens cannot be opened during this operation.
Note 2 If the PLC is already stopped, step (3) is skipped.
The PLC will not start running even when the operations are completed.
Note 3 If the INPUT key is pressed without inputting anything at the "~Y/N" display, the error "E01
SETTING ERROR" will occur.
Note 4 Even if the PLC RUN/STOP changeover is prohibited (R2925/bit2 ON), the PLC will stop
with step (3).
49
1. M60 / M60S Series
1.5 How to backup / recover /replace the NC unit
1.5.1.2 Restoration Operations
The parameters are restored from the maintenance memory cassette to the NC with the following steps.
(1)
Execute emergency stop.
#( ) ( )
"EMG EMERGENCY" will appear at the EMG EMERGENCY
operation message area.
WORK PROCESS I/O PAR SETUP MENU
(2)
Input "2" at the setting area # ( ),
and press the INPUT key. #(2) ( ) PLC STOP Y/N
EMG EMERGENCY
"PLC STOP Y/N" will appear at the
WORK PROCESS I/O PAR SETUP MENU
message area.
(3)
Input "Y" at the setting area ( ),
and press the INPUT key. #(2) ( Y) RESTORE EXEC Y/N
EMG EMERGENCY
"RESTORE EXEC Y/N" will appear at WORK PROCESS I/O PAR SETUP MENU
the message area.
(4)
Input "Y" at the setting area ( ),
and press the INPUT key. #(2) ( Y) RESTORE EXECUTION
EMG EMERGENCY
(a) The message "RESTORE EXECUTION"
WORK PROCESS I/O PAR SETUP MENU
will appear while the parameters are
being restored.
(b) The message "RESTORE COMPLETE"
will appear when the restoration is
completed. #( ) ( ) RESTORE COMPLETE
EMG EMERGENCY
WORK PROCESS I/O PAR SETUP MENU
Note 1 Other screens cannot be opened during this operation.
Note 2 If the PLC is already stopped, step (3) is skipped.
The PLC will not start running even when the operations are completed.
Note 3 If the INPUT
key is pressed without inputting anything at the "~Y/N" display, the error "E01
SETTING ERROR" will occur.
Note 4 Even if the PLC RUN/STOP changeover is prohibited (R2925/bit2 ON), the PLC will stop
with step (3).
50
