Page 1 of 27

SOUTH CENTRAL RLY

DY. CSTE-C-GTL-S AND T
DY.CSTE/CONSTRUCTION,
S.C.RAILWAY, D.R.M.OFFICE
COMPOUND
GUNTAKAL, 515801
Andhra Pradesh, India

Letter No: DY. CSTE-C-GTL-S AND T / G-SG-CN-GY-SIGG-3-2020 /

Dated: 17/02/2021
00922460032303

M/s VINEELA ENTERPRISES-HYDERABAD

FLAT NO.101, MORNI DEVI NIVAS
WEST MAREDPALLY,SECUNDERABAD
HYDERABAD- 500026
Telangana, India

Sub: Letter Of Acceptance

Ref: 1. Tender No. G-SG-CN-GY-SIGG-3-2020 closing date 02-11-2020 15:00 for (1)
Provision of Centralized Electronic Interlocking System with Hot stand by
architecture and MACLS Outdoor Signalling works at GOOTY BYE PASS and
GOOTY Jn. (2) Diversion and Shifting Of S&T gears in connection with the MACLS
Outdoor Signalling works at GOOTY BYE PASS and GOOTY Jn.
2. Your bid ID 11747822 dated 02/11/2020 14:20

The Competent Authority has accepted your offered rates in connection with the subject work. The
total cost of the work at the accepted rates works out to Rs. 61691750.65 (Rupees Six Crore Sixteen Lakh
Ninety-One Thousand Seven Hundred And Fifty Rupees And Sixty-Five Paise Only)

A sum of Rs.366500 deposited as Earnest Money vide IREPS reference ID NE752310829627 has
been retained towards initial Security Money for due and faithful fulfillment of the contract, and the
balance Security Money will be recovered from the progressive bills @ 6 % of the bill amount till it
reaches 5 % of the contract value in terms of clause 16 (1) of Part-II of IRSGCC July2020.

You are requested to submit Performance Guarantee in the form as given in Clause 16 (4) of Part-II of
IRSGCC July2020 equivalent to 3 % of the contract value amounting to Rs. 1850752.52 (Rupees Eighteen
Lakh Fifty Thousand Seven Hundred And Fifty-Two Rupees And Fifty-Two Paise Only) within 21 days
from the date of issue of Letter of Acceptance, valid up to stipulated date of completion plus 60 days so
that contract agreement can be executed. (1) Extension of time for submission of PG beyond 21 (Twenty
one) days and upto 60 days from the date of issue of LOA may be given by the Authority who is
competent to sign the contract agreement. However, a penal interest of 12% per annum shall be charged
for the delay beyond 21(Twenty one) days, i.e. from 22nd day after the date of issue of LOA. Further, if
the 60th day happens to be a declared holiday in the concerned office of the Railway, submission of PG
can be accepted on the next working day. In all other cases, if the Contractor fails to submit the requisite
PG even after 60 days from the date of issue of LOA, the contract is liable to be terminated. In case
contract is terminated railway shall be entitled to forfeit Earnest Money Deposit and other dues payable
against that contract. In case a tenderer has not submitted Earnest Money Deposit on the strength of their
registration as a Startup recognized by Department of Industrial Policy and Promotion (DIPP) under
Ministry of Commerce and Industry, DIPP shall be informed to this effect.(2)The failed Contractor shall
be debarred from participating in retender for that work.(3)The successful bidder shall submit the
Performance Guarantee (PG) in any of the following forms, amounting to 3% of the contract value:(i) A
deposit of Cash;(ii)Irrevocable Bank Guarantee;(iii)Government Securities including State Loan Bonds at
5% below the market value;(iv)Deposit Receipts, Pay Orders, Demand Drafts and Guarantee Bonds.
These forms of Performance Guarantee could be either of the State Bank of India or of any of the
Nationalized Banks;(v)Guarantee Bonds executed or Deposits Receipts tendered by all Scheduled Banks;
(vi)Deposit in the Post Office Saving Bank;(vii) Deposit in the National Savings Certificates;(viii)Twelve
years National Defence Certificates;(ix)Ten years Defence Deposits;(x) National Defence Bonds and(xi)
Unit Trust Certificates at 5% below market value or at the face value whichever is less. (xii) FDR. (4) The
Performance Guarantee shall be issued in favour of FA&CAO/Construction, S.C.Railway, Guntakal.

The entire work shall be completed within 24 month from the date of issue of Letter of Acceptance.

GCC: The General conditions and special conditions mentioned in the documents attached to NIT are

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 2 of 27

applicable and should be adhered

GST: The rate offered includes rate for the service/activity and applicable taxes as per GST law i.e. GST
act and rules applicable from time to time and the tenderer shall be responsible for deposition of
applicable GST to the concerned authority for the bills claimed.

General Conditions: All the rules and conditions governed by Indian Railway standard General conditions
of Contract July 2020 with up to date correction slips will apply for this tender and conditions, special
conditions & technical specification forming part of the Railway tender papers will apply to this contract
as mentioned and documents attached to NIT will apply for this tender, unless otherwise modified.

Releasing of SD & PG: The tender Performance Guarantee and security deposit shall be released after
physical completion of work based on completion certificate whereas Security Deposit shall be released
after completion of maintenance period (as mentioned in tender document) based on completion certificate
issued by the competent authority and after passing the final bill based on No Claim Certificate from the
contractor.

Labour & Wages: The contractor should abide by the provisions of payment of wages act & Minimum
wages act in terms of clause 54 and 55 of Indian Railways General conditions of Contract. In order to
ensure the same, an application has been developed and hosted on website
'www.shramikkalyan.indianrailways.gov.in'. Contractor shall register his firm/company etc., and upload
requisite details of labour and their payment in this portal. These details shall be available in public
domain

Qualified Engineer at Work site: In terms of provisions of new Clause 26A.1 to the General Conditions of
Contract (GCC), contractor shall also employ following Qualified Engineers during execution of the
allotted work (a)One Qualified Graduate Engineer when cost of work to be executed is Rs. 200 lakh and
above, and (b) One Qualified Diploma Holder Engineer when cost of work to be executed is more than
Rs. 25 lakh, but less than Rs, 200 lakh. Further, in case the contractor fails to employ the Qualified
Engineer, as aforesaid in Para above, he, in terms of provisions of Clause 26A.2 to the General Conditions
of Contract, shall be liable to pay an amount of Rs. 40,000 and Rs. 25,000 for each month or part thereof
for the default period for the provisions, as contained in Para (a) and (b) above respectively

Execution of Contract Agreement: It may please be noted that until a formal agreement is executed,
acceptance of the tender shall constitute a valid and binding contract between your firm and the Railways
subject to the modifications as may be mutually agreed to.

All Other terms and conditions, as stipulated in the tender documents shall be applicable.

SURYANARAYANA DADI
Dy.CSTE/C/GTL
Digitally Signed
View Signature Details

Awarded Quantities And Rates

Item Item Desc Item Item Qty Unit Rate Escl. Advt.Value Bid Rate/ Bid Amount
Sno. Code Qty Unit (Rs) (%) (Rs) Unit Rate (Rs)
%
Schedule A1-SOR ITEMS - SUPPLY PORTION (Item Directory - Not Applicable) 10323125.00 44.00 14865300.00
Above
CHAPTE-1 : SIGNAL UNITS Supply of
CLS post 140mm dia. 4.5M long to
1 specification IRS.S.6.81 .or latest. 101 25 Numbers 3238.00 At Par 80950.00
NOTE : MATERIAL SHALL BE
INSPECTED BY RITES
Supply of CLS post 140mm dia. 3.5M
long to specification IRS.S.6.81 or
2 102 7 Numbers 3039.00 At Par 21273.00
latest NOTE : MATERIAL SHALL BE
INSPECTED BY RITES
Supply of CLS ladder set complete with
staging, supports, signal number plate,
cast iron ladder base to suit 4.5 Metre
3 103 25 Set 4422.00 At Par 110550.00
post as per drg.no.SA.23153.S.2033.
or latest NOTE : MAERIAL SHALL BE
INSPECTED BY RITES
Supply of CLS ladder set complete with

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 3 of 27

staging, supports, signal number plate,

cast iron ladder base to suit 3.5 Metre
4 post as per drg.no.SA.23150.S.2033. 104 7 Set 3574.00 At Par 25018.00
NOTE: MATERIAL SHALL BE
INSPECTED BY RITES
Supply of Surface base 140mm dia.
post to suit item no. 1 & 2 as per
5 Drg.S.2011/M or latest NOTE : 105 32 Numbers 2370.00 At Par 75840.00
MATERIAL SHALL BE INSPECTED BY
RITES
Supply of Offset bracket to suit
140mm dia. CLS post with two
numbers of 'U' bolts and nuts complete
6 106 18 Numbers 3377.00 At Par 60786.00
as per SA-23080 or latest NOTE :
MATERIAL SHALL BE INSPECTED BY
RITES
Supply of Calling On signal unit
complete and 'U' bolts to drawing
7 no.SA.24381 /Adv. Or latest NOTE : 107 23 Numbers 3242.00 At Par 74566.00
MATERIAL SHALL BE INSPECTED BY
RITES
Supply of position light shunt signal
ground type complete with base , Pipe,
hoods, wire mesh, Number plate lamp
holders, terminal block to
8 108 4 Numbers 4160.00 At Par 16640.00
Drg.No.SA.23840/Adv./Alt.1 - S.23202
(Adv.) Specn. IRS: S.6/81. or latest
NOTE : MATERIAL SHALL BE
INSPECTED BY RITES
Supply of position light shunt signal
Post type with hoods, Lenses, Number
plates, lamp holder, wire mesh and
terminal block and offset bracket to
suit 90mm sockets (CLS) with 2 Nos of
9 'U' Bolts and nuts complete to fix 109 10 Numbers 2416.00 At Par 24160.00
calling on signal/ shunt signal below
main stop signal as per to
Drg.No.S23840/latest NOTE :
MATERIAL SHALL BE INSPECTED BY
RITES
Supply of Colour light signal unit: (1) 2
aspect complete to Drg. No. SA.
10 23002/A/M with latest amendment and 11501 21 Numbers 8939.00 At Par 187719.00
IRS S 26/64. NOTE : MATERIAL SHALL
BE INSPECTED BY RITES
SUPPLY OF COLOUR LIGHT SIGNAL
UNIT : 3 aspect complete to Drg. No.
11 SA. 23003/A/M with latest amendment 11502 11 Numbers 12120.00 At Par 133320.00
and IRS S 26/64. NOTE : MATERIAL
SHALL BE INSPECTED BY RITES
Supply of junction type/directional
type route indicator 1-way to
12 drg.No.SA 23402 with IRS-S66/84 110 5 Numbers 10591.00 At Par 52955.00
with Amd1 NOTE : MATERIAL SHALL
BE INSPECTED BY RITES
Supply of junction type/directional
type route indicator 2-way to
13 drg.No.SA 23402 with IRS-S66/84 111 5 Numbers 19110.00 At Par 95550.00
with Amd1 NOTE : MATERIAL SHALL
BE INSPECTED BY RITES
supply of junction type/directional type
route indicator 4-way to
14 drg.No.SA23402 with IRS-S66/84 with 112 1 Numbers 31952.00 At Par 31952.00
Amd1 NOTE : MATERIAL SHALL BE
INSPECTED BY RITES
CHAPTER-2 : LOCATION BOXES Supply
of GKP type Location Boxes Half size
15 drg. No. S&T/MFT/2378 (Half). NOTE : 202 23 Numbers 5529.00 At Par 127167.00
MATERIAL SHALL BE INSPECTED BY
RITES
Supply of E-type locks of different
wards as per requirement with key per
E-type lock to Drg. No.SA.3376/M/
16 204 6 Numbers 560.00 At Par 3360.00
LATEST AND RDSO specn
No.IRS.S.30/64 NOTE : MATERIAL
SHALL BE INSPECTED BY RITES
Supply of relay fixing frame for Full
location box, the frame should be

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 4 of 27

made out MS angle of 25mm X 25mm

X 3mm and approximate size of
17 205 70 Numbers 591.00 At Par 41370.00
940mm X 150mm with suitable holes
to fix the same in the box.
Supply of hylam sheet, resin bonded,
6mm thick, grade P3, to IS
18 specification IS: 2036 of 1974 or latest 206 6 Numbers 4821.00 At Par 28926.00
and size 2400mm X 1200mm of colour
approved by the site in-charge
Supply of GKP type Location Boxes Full
size as per drg. No. S&T/MFT/2378
19 201 115 Numbers 8960.00 At Par 1030400.00
(Single). NOTE : MATERIAL SHALL BE
INSPECTED BY RITES
CHAPTER - 3 : POINT MACHINE
RELATED ITEMS Supply of Ground
Connections for the universal type
20 302 46 Set 5767.00 At Par 265282.00
point machines as per drg.no.
RDSO.S.3362. NOTE : MATERIAL
SHALL BE SUPPLIED BY RITES
Supply of insulations for 'D' clamp
switch extension bracket to suit to
universal point machine as per drawing
supplied by the Railways. (One set
21 304 46 Set 496.00 At Par 22816.00
consists of 'D' clamp insulation - 2 No.
Nylon insulation bushes 4 No., Nylon
insulation washers - 8 No.). (To be
procured from RDSO approved firm).
Supply of drive lug insulation for
universal point machine to be procured
from RDSO approved firms. (One set
22 305 46 Set 109.00 At Par 5014.00
consists of one number central
insulation plate, bushes - 2 No. and
washers - 4 No.).
Fabrication and supply of GI
termination box for point machine of
size 45cm x 23cm x 12 cm, the
termination box to be fabricated out of
GI sheet 10SWG. The termination box
to be provided with 2 nos of M.S.
angle of size 50x50x6mm of length
1000mm each and GI pipe of 40 mm
dia and length of 450mm. The
termination box is also provided with
23 teak wood plank of size 25 mm 2304 48 Numbers 2579.00 At Par 123792.00
thicknesses for fixing of terminals.
Necessary bolts, nuts and screws are
to be provided for fabrication of
termination box. The termination box
is to be painted double coat with
approved quality of paint black enamel
on to the outside and to be painted
with white enamel in to inside of the
box (All materials are to be procured
by the contractor).
CHAPTER-4 : TRACK CIRCUIT
RELATED ITEMS Supply of track feed
regulating resistance disk type 0 to 30
24 405 85 Numbers 243.00 At Par 20655.00
ohms as per Drg.No.SA. 20161/ 66/M
or latest. To be procured from RDSO
approved firms
Supply of B type chokes to
specification no.IRS-S.65/83 to
25 amendment no.1 or latest. NOTE : 406 170 Numbers 1604.00 At Par 272680.00
MATERIAL SHALL BE INSPECTED BY
RDSO
Stationary low maintenance secondary
lead acid cells as per RDSO
specification IRS-S-88/2004 with
topping up frequency upto 6 months.
26 This includes supply of inter cell 40702 270 Numbers 2190.00 At Par 591300.00
connectors, bolts nuts, acid level
indicating floats and vent plugs. (1) 2
volts 80 AH NOTE : MATERIAL SHALL
BE INSPECTED BY RDSO
27 Supply of Hydro meter. 408 8 Numbers 191.00 At Par 1528.00
Supply of distilled water for topping of
28 secondary cells.( to be supplied at 409 1000 Litre 7.00 At Par 7000.00
site.) IS 1106

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 5 of 27

Supply of Track lead junction boxes

fiber glass as per Drg.No.CWM-
00597of F.R.P material to IRS.S.23
specification along with fixtures i.e., on
MS angle 50x50x5mm, 0.9 Meters long
29 two numbers of G.I. pipes of 25mm 403 380 Numbers 1057.00 At Par 401660.00
dia. along with nuts and bolts and
500mm long (this includes gromite
bushes, 60mm PBT terminal). NOTE :
MATERIAL SHALL BE INSPECTED BY
RITES
CHAPTER - 5 : RELAYS Supply of AC
immune, plug-in-type, Style QTA2 DC
Neutral track, 9 ohm, 2F.1B contacts,
front and back contacts metal to
carbon, complete with plug-board,
retaining clip and connectors
30 503 85 Numbers 3271.00 At Par 278035.00
conforming to BRS: 939A, BRS: 966
(Appendix F2), IRS:S 34 & IRS:S 23
(as applicable). The interlocking code
for this unit shall be FGHKX.(with ATC
clips) NOTE : THE MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Relay, plug-in type, Style
AC-LED All aspects, AC lamp proving
relay unit with in-built current
transformer type, slow release neutral
line relay, 4F.4B contacts, front and
back contacts metal to carbon, shall be
suitable for working in series with the
110V AC, LED signal lamp Rate (in
31 504 92 Numbers 4831.00 At Par 444452.00
Rupees)d at 15W confirming to RDSO
spec. STS/E/Relays/AC lit LED
signal/09-2002, BRS 941A,IRS:s34 &
IRS:S23 (as applicable). The
interlocking code for this unit shall be
ABDHK(with ATC clips). NOTE :
MATERIAL SHALL BE INSPECTED BY
RDSO
Supply of point contactor relay QBCA-1
AC immunized miniature plug in type
DC biased contractor, attractive
armature 24Voits DC with 2HF/4B
contacts, Heavy duty front contact,
32 contacts metal to carbon complete 506 28 Numbers 6859.00 At Par 192052.00
with plug board, retaining clips and
connectors to specification. BRS
943,IRS.S34, IRS.S.23 as applicable
NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Relay Non-AC immune, plug-
in-type Style 'QN1, DC neutral line,
24V, 8F.8B contacts, front and back
contacts metal to carbon with plug
board retaining clip and connectors
33 507 70 Numbers 2992.00 At Par 209440.00
confirming to BRS 930, IRS-S34, IRS-
S23 (as applicable). The interlocking
code for this unit shall be ABCDF.(with
ATC clips) NOTE: MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Relay, Non-AC immune plug
in type, style QN1, DC neutral line,
24V, 12F.4B contacts, front and back
contacts metal to carbon with plug
board, retaining clip & connectors
34 conforming to BRS:930, IRS: S 34 & 508 180 Numbers 2930.00 At Par 527400.00
IRS:S 23 (as applicable). The
interlocking code for this unit shall be
ABCDE.(with ATC clips) NOTE :
MATERIAL SHALL BE INSPECTED BY
RDSO

Supply of Relay AC immune, plug-in-

type Style 'QNA1, DC neutral line, 24V,
8F.8B contacts, front and back
35 contacts metal to carbon with plug 509 140 Numbers 3173.00 At Par 444220.00
board retaining clip and connectors
confirming to BRS 931A, IRS-S60,
IRS-S34 and IRS-S23 (as applicable).
The interlocking code for this unit shall

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 6 of 27

be ABDGH.(with ATC clips) NOTE :

MATERIAL SHALL BE INSPECTED BY
RDSO
Supply of Relay AC immune, plug-in-
type Style 'QNA1, DC neutral line, 24V,
12F.4B contacts, front and back
contacts metal to carbon with plug
board retaining clip and connectors
36 510 90 Numbers 3143.00 At Par 282870.00
confirming to BRS 931A, IRS-S60,
IRS-S34 and IRS-S23 (as applicable).
The interlocking code for this unit shall
be ABDFH. NOTE : MATERIALS SHALL
BE INSPECTED BY RDSO
Supply of Relay AC immunized, plug in
type, style QNA1K, DC neutral line,
24V 1000 ohms, 6F.6B contacts, front
contacts metal to carbon and back
contacts metal to metal / carbon,
complete with plug board, retaining
clip and connectors conforming to BRS
37 512 12 Numbers 3178.00 At Par 38136.00
931A, IRS S60, IRS S34, IRS.S23 and
RDSO specification STS/E/Relays/UEA
(PI), dated 30-6-97 (Annexure - II)
(as applicable). The interlocking code
for this unit shall be CDEKY.(with ATC
clips) NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of AC immunized plug-in-type
Style 'QSPA1', DC Neutral line, slow to
pickup, 24V, 8F.4B contacts, front and
back contacts metal to carbon,
complete with plug board, retained clip
38 & connectors conforming to BRS:933A, 502 85 Numbers 4367.00 At Par 371195.00
IRS:S 60, IRS:S 34 & IRS:S 23 (as
applicable). The interlocking code for
this unit shall be ABDEJ.(with ATC
clips) NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
CHAPTE-6 : RELAY RACKS, TERMINAL
BLOCKS AND ND FUSES : Supply of
terminal block 1 way PBT 60mm as per
39 RDSO Drg.No. SA.23745/Alt.5 & IRS 603 1800 Numbers 61.00 At Par 109800.00
S.75/91 & IRS.S.23 with latest
amendment. NOTE : MATERIAL SHALL
BE INSPECTED BY RDSO
Supply of terminal block 6 way PBT
25mm as per RDSO Drg.No.
SA.23756/Alt.3 & IRS S.75/91 &
40 604 2000 Numbers 285.00 At Par 570000.00
IRS.S.23 with amendment no.2 or
latest. NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Non-deteriorating type of
fuse holders & fuse links - electric fuse
for Railway signalling Rated voltage
240 AC/DC to Specn. No. IRS S.78/92
(IRS-S-78/97 Tentative) IS:13703
41 (part 2/sec2):1993 suitable for E1 fuse 60701 1000 Numbers 150.00 At Par 150000.00
20Amps SC-20 Holder Safe Clip / knife
edge type size E1 (R-SS) amp. Supply
of Fuse holder 20A capacity NOTE :
MATERIAL SHALL BE INSPECTED BY
RDSO
Supply of Fuse links 2 Amps. NOTE :
42 MATERIAL SHALL BE INSPECTED BY 607d 800 Numbers 20.00 At Par 16000.00
RDSO
SUPPLY OF Fuse links 16 Amps.
43 NOTE : MATERIAL SHALL BE 607b 400 Numbers 21.00 At Par 8400.00
INSPECTED BY RDSO
Supply of Fuse links 10 Amps. NOTE :
44 MATERIAL SHALL BE INSPECTED BY 607c 100 Numbers 21.00 At Par 2100.00
RDSO
Supply of Fuse links 6 Amps. NOTE :
45 MATERIAL SHALL BE INSPECTED BY 607f 100 Numbers 21.00 At Par 2100.00
RDSO

Supply of Cable termination racks size

880mm x 2 Meters made out of
50mmx50mmx6mm thick MS angle
with stainless steel nuts and bolts for

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 7 of 27

fixing of the rack with POWDER

COATED and drilling suitable holes to
suit hylam sheet and relay frames
complete as per standard practice with
tripod bases and reel insulators (for K
rack, P rack and power rack) and with
46 602 2 Numbers 5125.00 At Par 10250.00
cable ladder of width 400mm and
length of 2 Mtr.. The thickness of angle
to be 5mm. two angles of
40mmX40mmX5mm to be supplied at
both ends and supporting flats of
25mm X5mm.
CHAPTER-7 : WIRES AND CABLES :
Supply of PVC insulated wire multi-
strand copper conductor 10 Sq.mm
flexible Specn.IRS.S76/89.
Amendment No.2 or latest. Each coil of
47 100 mts length. To be procured from 703 20 Numbers 9390.00 At Par 187800.00
RDSO approved firms (size
140/0.3mm)( Red-10 and Black-10)
NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO. QTY. UNIT TO
BE READ AS COIL
Supply of PVC wire coils of size 28/03
multi strand (flexible). Specn. IRS.S
76/89. Amendment No.2 or latest.
Each coil of 100 meters length. To be
48 procured from RDSO approved firms. 704 20 Numbers 1635.00 At Par 32700.00
( Red-10 and Black-10) NOTE :
MATERIAL SHALL BE INSPECTED BY
RDSO. QTY. UNIT TO BE READ AS
COIL
Supply of indoor cable 60 core X
0.6mm as per IRS S.76/89 amend
49 701 0.5 Kilometre 128938.00 At Par 64469.00
no.2 or latest. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO
Supply of PVC insulated wire copper
conductor 16/02mm to ATC IS:694 to
RDSO specification no.IRS.S76/89.
50 Each coil of 100 mts length. To be 702 300 Numbers 797.00 At Par 239100.00
procured from RDSO approved firms.
NOTE : QTY.UNIT TO BE READ AS
COIL
CHAPTER-9 : DOMINO PANEL &
DATALOGGERS : Supply of Data
Logger with 512 Digital inputs and 32
Analog inputs for remote monitoring
with net work facility of signalling
parameters and power supply
arrangements to confirming to Specn.
51 903 1 Set 383224.00 At Par 383224.00
No. IRS. S.99/2006 with 64 input
digital cord as a spare and fuse
monitoring PCBs for monitoring at
least 50 No. of 2 Amps Fuses, with
inbuilt modem cards for networking.
NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
CHAPTER -10 : STATIONARY &
MISCELLANEOUS ITEMS Supply of
52 1002 160 Numbers 60.00 At Par 9600.00
Universal locks with one key for every
ten locks.
Supply of Cement Portland / Ordinary,
confirming to ISS: 269/76.(To be
53 1004 10 MT 4027.00 At Par 40270.00
supplied at site as per requirement
and as per instruction of site engineer)
Supply of Office table with plywood
plank with thickness of 18mm,
teakwood beading with three draws of
54 1008 2 Set 7035.00 At Par 14070.00
size 4' X 2' with heavy duty 'S' type
chair with hand rest. The above is of
Godrej or similar make.
Supply of steel stools 18" height neatly
55 1009 4 Numbers 334.00 At Par 1336.00
finished and painted.
Supply of Navtal Locks Godrej make
56 50mm as per instructions of SE/SSE 1013 10 Numbers 384.00 At Par 3840.00
(Sig) at site.

Supply of key chains with ring with

plastic name plate of

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 8 of 27

60mmx20mmx3mm duly engraving

station name on one side and key
57 1014 60 Numbers 23.00 At Par 1380.00
particulars on one side as specified by
the site in-charge.
Printing, Binding & supply of the
following registers with latest proforma
given by in-charge officer each
Register of 100 pages.. a) Station
Asset Register b) Deficiencies c)
Officer Inspection book d) Work site
orientation classes note book. e)
Station Message book f) Infringement
measure book for signal gears g)
Route cancellation register. h) Relay
room Key register i) Selection circuit
testing j) Cable testing summary k)
Siganl maintenance record. l) Power
Supply systems(Battery maintenance )
58 m) Mechanical Signalling Register. n) 1017 50 Numbers 70.00 At Par 3500.00
Axle Counter Maintenance Register o)
Block instrument Maintenance
Register. p) Track circuit maintenance
Register. q) Lifting barriers
maintenance Register. r) Electrically
operated point maintenance Register.
s ) Electronic Interlocking Maintenance
Register. t) Location box maintenance
Register. u) Earth Testing record
Register. v) Cabin/Relay room register.
w) Joint Inspection of Points and
Crossings register. x) Block Proving
Axle Counter Register. y) Diesel
generator /Solar panel Register.
Supply of the following
resistors/condensers/diodes. A)
Electrolytic condensers 50V 470 mfd.-
20 nos (B) Electrolytic condensers 50V
59 1003 4 Set 2562.00 At Par 10248.00
1000 mfd - 20 No.(C ) Wire wound
resistances 100 ohms 10 Watts - 20
No. (D) Diodes - BY 127 - 10 Nos & (E)
PVC Insulation tapes of 25 Mtr.-25 No.
Supply of Jerry can 20 Ltrs capacity
60 white as per the requirement of SI at 1012 2 Numbers 105.00 At Par 210.00
site.
CHAPTER-15 - BPAC RELATED ITEMS
Supply of Single Section Digital Axle
Counter,as per Specification No.
61 RDSO/SPN/177/ 2005 (Version-2) or 1501 1 Set 507019.00 At Par 507019.00
latest with inbuilt event logger card.
NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of spare cards for Digital Axle
62 Counter : Micro controller logic card 150201 1 Numbers 36825.00 At Par 36825.00
(MLB1 or MLB2)
63 Supply of Modem card 150202 1 Numbers 24550.00 At Par 24550.00
64 Supply of DC-DC Converter card 150203 1 Numbers 12275.00 At Par 12275.00
Supply of Signal Conditioner card
65 150204 1 Numbers 24550.00 At Par 24550.00
(SSC1 or SSC2)
66 Supply of Relay Driver Card 150205 1 Set 22096.00 At Par 22096.00
Supply of Web detectors (each set
67 consists of 2 Nos Tx and 2 Nos Rx 150206 1 Set 30221.00 At Par 30221.00
coils).
Supply of Reset Box for single section
Digital axle Counter System as per
68 150207 1 Numbers 34198.00 At Par 34198.00
RDSO specification No.
RDSO/SPN/177/2005 or latest
69 Supply of Event Card 150208 1 Numbers 23450.00 At Par 23450.00
Supply of Reset card for reset box of
single section Digital axle Counter
70 150209 1 Numbers 11725.00 At Par 11725.00
System as per RDSO specification
No.RDSO/SPN/177?2005 or latest

CHAPTER -16 :EARTHING RELATED

ITEMS Supply of 35 Sq.mm Multi-
71 strand single core PVC insulated 1603 600 Metre 303.00 At Par 181800.00
copper cable as per IS:694 for
connecting Main earth electrode to
MEEB in the equipment room in

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 9 of 27

duplicate.
Supply of 16 Sq mm Multi-stand single
core PVC Insulated copper cable as per
72 1604 300 Metre 144.00 At Par 43200.00
IS:694 for connecting MEEB to SEEB
and SPDs and SPDs to MEEB.
Supply of lightening and surge
arrestors of class B&C suitable for
single phase supply in TT network as
per amendment 5 of RDSO spec.
73 No.RDSO/SPN/165/2004 or Latest and 1602 1 Set 14999.00 At Par 14999.00
as recommended by RDSO letter
No.STS/E/l PS/GENL dated 27.01 .06
(Amendment5) NOTE : MATERIAL
SHALL BE INSPECTED BY RITES
Supply of Battery charger of 230Volts
AC / 110V DC 30 Amps single phase,
signalling / telecom. Instrument as per
74 806 1 Numbers 74911.00 At Par 74911.00
RDSO Specn. IRS S.86/2000 Amd.1 or
latest. NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Transformer Rectifier 110V
AC Input /24V-30V DC Output,5 Amp
capacity, as per spec. IRS S 91-93
75 with amendment 1 to be procured 815 6 Numbers 3196.00 At Par 19176.00
from RDSO approved firms. NOTE :
MATERIAL SHALL BE INSPECTED BY
RDSO
CHAPTER -12 : MECHANICAL
SIGNALLING ITEMS Supply of Electric
Key Transmitters single complete to
76 drg.no.SA.22601/Alt-4& IRS 1201 5 Numbers 4767.00 At Par 23835.00
S.21/2001 to ward no. specified.
NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
77 Supply of double key lock. 1202 2 Numbers 303.00 At Par 606.00
Supply of wire rope steel galvanised
6/19, 26 SWG for double wire
78 1204 400 Kg 81.00 At Par 32400.00
signalling to specn. No. IRS. S3-
61,Amd-1.
CHAPTER 14 BLOCK & IB RELATED
Supply of filter unit for Block
79 instrument As per IRS S.68/89 NOTE : 1402 1 Numbers 10350.00 At Par 10350.00
MATERIAL SHALL BE INSPECTED BY
RDSO
Supply of Block Bell equipment to IRS
80 TC 44/88 NOTE : MATERIAL SHALL BE 1403 1 Numbers 1739.00 At Par 1739.00
INSPECTED BY RDSO
CHAPTER -18 :MISCELLANEOUS ITEMS
81 Supply of copper lugs10 Sqmm of 1810 400 Numbers 8.00 At Par 3200.00
reputed make
Supply of Corium Z 105 Battery
82 cleaner and terminal conditioner of 1812 2 Numbers 3507.00 At Par 7014.00
500ml tin can
Supply of Copper eyelets to suit 16/0.2
83 1813 1600 Numbers 2.00 At Par 3200.00
wire Dowell's make
Supply of Copper eyelets to suit
84 1814 200 Numbers 4.00 At Par 800.00
10.sqmm wire Dowell's make
Supply of 2 N/2R Micro switch, L&T or
85 1817 6 Numbers 378.00 At Par 2268.00
Siemens make.
Supply of 24 volts impulse counter 6
86 1818 10 Numbers 938.00 At Par 9380.00
digits. (Keltron or Gujral make)
Vulco tape of size 45mm width x 1.5
mm thick x 10 Mtr. length. It shall be
87 self bonding type anti corrosive, heat 1808 12 Numbers 1524.00 At Par 18288.00
resistant & water proof. NOTE : QTY
UNIT TO BE READ AS ROLL
CHAPTER -11 : TELECOM EQUIPMENT
ITEMS Supply of Thermo shrinkable
jointing kit as per Spec. No. IRS TC.
88 77/2012(Rev.3 and Amd.3) for all 1102 20 Numbers 1923.00 At Par 38460.00
types joints suitable for 6 Quad Jelly
filled UG cable. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO
Supply of Four Wire DTMF way station
equipment RDSO Spec No TC
89 1103 4 Numbers 3833.00 At Par 15332.00
60/2007/Amdt 1/latest and Telephone
to suite RDSO specification TC38/97 or

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 10 of 27

latest.
Supply of Power supply unit 2 Amps as
per Spec. No. IRS. TC.72/97 with
90 1105 2 Numbers 2925.00 At Par 5850.00
Amendment 1 or latest with 12
volts /7 AH MF battery.
Supply of HDPE telecom duct with
outer diameter of 40mm and inner
diameter of 33mm permanently
lubricated as per Specn. No.
RDSO/SPN/TC-/45/2006 Revision 1.0
or latest or as per specification TEC GR
No.G/CDS-08/02,NOV 2004 or latest.
HDPE pipe shall be supplied along with
91 1108 1 Kilometre 45226.00 At Par 45226.00
4mm dia polypropylene rope of
approved quality inside wherever
required. The length of HDPE telecom
duct should be 1 KM. End plugs to be
provided along with drum (free of
cost) (2 No. per Km.). NOTE :
MATERIAL SHALL BE INSPECTED BY
RDSI
HDPE duct associated accessories and
tools as per the specification of
92 NS.1108 Plastic couplers - Slip fit / 110901 2 Numbers 58.00 At Par 116.00
push type for HDPE duct (2 No. per
Km.).
Supply of End plug for HDPE duct (2
93 110902 2 Numbers 23.00 At Par 46.00
No. per KM).
Supply of Cable sealing plugs for HDPE
94 110903 2 Numbers 29.00 At Par 58.00
duct (1 No. of per Km.)
Supply of desk type 2 wire, 12 way
DTMF selective calling group telephone
complete as per specification IRS. TC.
95 1110 4 Set 4257.00 At Par 17028.00
80-2000, Amendment-3 or latest.
NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of 10 pair switch Board cable of
96 0.6mm dia /Delton make as per TEC 1112 500 Metre 24.00 At Par 12000.00
spec No GR/WIR-06/03 of March 2002
97 Supply of RJ 11 RESET boxes 1118 10 Numbers 24.00 At Par 240.00
Supply of PVC twin core flat copper
98 1119 1 Kilometre 6600.00 At Par 6600.00
cable
Supply of VF Tapping Transformer
99 470:600 Ohms to RDSO Spec No. 1123 6 Numbers 643.00 At Par 3858.00
IRS.TC.22-76 or latest
Supply of VF Transformer 1120 : 470
100 as per RDSO Specification No. 1125 12 Numbers 609.00 At Par 7308.00
IRS.TC.22-76 or latest.
Supply of Splice Enclosure 24 Fiber to
101 RDSO Spec.RDSO/SPN/TC/2006 1140 6 Numbers 2417.00 At Par 14502.00
Rev.0, Amdt 1 or Latest
Operation of any SOR Item from
102 ANYSOR 2 Lumpsum 200000.00 At Par 400000.00
Chapter-1 to 18 Except Chapter-11
Schedule Totals 14865300.00
Schedule A2-NON SOR ITEMS - SUPPLY PORTION (Item Directory - Not %
3082033.00 39.00 4284025.87
Applicable) Above
Earth Leakage detector 12 channels as
per RDSO Specn. No.
RDSO/SPN/256/2002 with latest
amendment including - 1) Mounting
stand for ELD and 2 fuse board to
1 isolate from distribution board, for the 1 1 Numbers 133187.00 At Par 133187.00
following requirement of channels:.
24V DC - 1 to 4 channels 110 DC - 5
to 8 channels 110V AC - 9 to 12
channels NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Earth cable pair insulation
2 2 1 Numbers 23742.00 At Par 23742.00
tester type 906M.
Supply of track feed battery charger to
work on 110V/AC input to charge 1,2,3
lead acid cells of 80AH with 10A
3 capacity with potential free contacts as 3 85 Numbers 5775.00 At Par 490875.00
per Spec No IRS: S.89/2013
version1.0 or latest. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 11 of 27

Supply of Vitreous enamel coating

board each of size 280mm X 102mm
made out of 2mm thick sheet (signal
4 4 66 Numbers 98.00 At Par 6468.00
number plate) with white back ground,
black letters as per technical
specifications.
Supply of Vitreous enamel coating
board each of size of 230mm dia (A, P,
G, C, IB markers) made out of 2mm
sheet as per following colour scheme.
5 5 33 Numbers 191.00 At Par 6303.00
(a) Supply of 'G' marker yellow
background, black letters. (b) Supply
of other boards: white background
black letters.
Supply of Multi Lamp Route indicator
(LED Single Digit) from 1 to 9 with
6 6 3 Numbers 49000.00 At Par 147000.00
white LED (Without Housing) as per
the following
Supply of Tips for ASM on Panel
operation boards, of size 16" X 18" in
7 7 1 Numbers 6500.00 At Par 6500.00
fibre sheet of 4mm thickness with
glassy lamination.
LVR Transformers rectifier
8 8 2 Numbers 1000.00 At Par 2000.00
230/24/1Amps
Supply of Godrej T-104 model or
9 9 1 Numbers 20569.00 At Par 20569.00
similar
Supply of Godrej PCH5d13R model or
10 10 1 Numbers 3801.00 At Par 3801.00
similar
Supply of Godrej PCH 5002T model or
11 11 1 Numbers 7360.00 At Par 7360.00
similar
Supply of Godrej shelf storage of 916 x
12 12 1 Numbers 18305.00 At Par 18305.00
486 x 1981 mm or similar
FIRE ALARM SYSTEM a) supply of
Microcontroller based fire alarm
monitoring & control unit ( semi
addressable only) of reputed make
along with12V-7AH batteries -2no.
Test Reports shall be submitted by
OEM, after Installation and commission
13 13 1 Numbers 7346.00 At Par 7346.00
OEM has to give the certification.
Technical specification Normal
working : IP-230V AC; OP24V DC, Opt
Curr: 250-300ma. Full Load
Condition : Opt Curr-2Amps, common
hooter OP: 4.5Amps, Individual Hooter
OP: 300Amps(max)
b)Supply of Alarm Hooter wit strobe of
reputed make. Test Reports shall be
14 submitted by OEM, after Installation 14 1 Numbers 2546.00 At Par 2546.00
and commission OEM has to give the
certification.
c) supply of 1" PVC Conduit pipe 10
15 15 20 Numbers 34.00 At Par 680.00
feet length
Supply of DWC pipe of 120m OD/103
ID to IS Spec.No.14930(part-II) for
UG cables of 6M length with one snap
16 16 100 Numbers 1134.00 At Par 113400.00
FIR coupler (colour other than black)
NOTE : MATERIAL SHALL BE
INSPECTED BY RITES
Supply of Dot Matrix Printer EPSON LQ
18 300/LX300, 18 column, with serial 18 1 Numbers 9000.00 At Par 9000.00
port.
Printer for Maintenance terminal at
19 Station. HP 1020 Laserjet or similar 19 1 Numbers 10797.00 At Par 10797.00
(Inspection by Consignee)
Manufacture and supply of Laminated
boards of size 45 cm X 60 cm X 12mm
thick for the following: 1. Battery care
20 20 2 Per Unit 2025.00 At Par 4050.00
board - 1 No. 2. Guide lines for power
supply arrangements - 1 No. NOTE :
PER UNIT TO BE READ AS PER BOARD
Manufacture and supply of Laminated
boards of size 45 cm X 60 cm X 12mm
21 thick for the following: 1. Relay room 21 1 Per Unit 1350.00 At Par 1350.00
maintenance board - 1 No. NOTE : PER
UNIT TO BE READ AS PER BOARD
22 Supply of Rodometer 22 1 Numbers 2940.00 At Par 2940.00

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 12 of 27

Supply of High Availability Single

Section Digital Axle Counter System
complete with dual sensor as per
RDSO specification No.
RDSO/SPN/177/2012 version 3.0 or
latest consisting of:- (i) Track side
high availability Digital Axle Counter
unit - 2 Nos. (ii) High frequency Tx coil
and Rx coil (each set consists of web
mounting type 2 Nos. Tx Coil and 2
23 Nos Rx coil). (iii) Vital Relay Box - 2 23 2 Set 704160.00 At Par 1408320.00
Nos. duly wired with following relays:
(a) Vital Relays QNA1K, 24V, 6F.6B - 2
Nos. (b) Reset Relay QNN1, 24V, 6F-
6B - 1 No. (c) PR Relay QNN1, 24V,
6F-2B (Dual) - 1 No. (iv) Clamp with
deflector plates and hardware - 4 Nos.
(v) Reset Box - 2 Nos. (vi) Surge
Voltage Protection Device Mounted on
DIN Rail - 2 Nos. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO
Spare cards for HA-SSDAC Axle
Counter supplied as above (a) Signal
conditioner Card No. 1 (SCC1) for
24 HASSDAC as per RDSO Specification 24 2 Numbers 29340.00 At Par 58680.00
No. RDSO/ SPN/.177/2012 with
version 3 or latest. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO
(b) Signal conditioner Card No. 2
(SCC2) for HASSDAC as per RDSO
Specification No. RDSO/
25 25 2 Numbers 29340.00 At Par 58680.00
SPN/.177/2012 with version 3 or
latest. NOTE : MATEIAL SHALL BE
INSPECTED BY RDSO
(c) Modem Card No.3 for HASSDAC as
per RDSO Specification No. RDSO/
26 SPN/.177/2012 with version 3 or 26 2 Numbers 29340.00 At Par 58680.00
latest. NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
(d) Dual Micro Controller Logic Card
No.4 for HASSDAC as per RDSO
Specification No. RDSO/
27 27 2 Numbers 78631.00 At Par 157262.00
SPN/.177/2012 with version 3 or
latest. NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
(e) Relay Driver Card No.5 for
HASSDAC as per RDSO Specification
28 No. RDSO/ SPN/.177/2012 with 28 2 Numbers 29340.00 At Par 58680.00
version 3 or latest. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO
(f) DC-DC Convertor Card No.6 for
HASSDAC as per RDSO Specification
29 No. RDSO/ SPN/.177/2012 with 29 2 Numbers 17604.00 At Par 35208.00
version 3 or latest. NOTE : MATERIAL
SHALL BE INSPECTED BY RDSO
(g) Wen detector (Each set consists of
2 Nos. of Tx and 2 Nos. of Rx coils) for
HASSDAC as per RDSO Specification
30 30 2 Numbers 39902.00 At Par 79804.00
No. RDSO/ SPN/.177/2012 with
version 3 or latest. NOTE : MATEIRAL
SHALL BE INSPECTED BY RDSO
(h) Reset box for HASSDAC as per
RDSO Specification No. RDSO/
31 SPN/.177/2012 with version 3 or 31 2 Numbers 42250.00 At Par 84500.00
latest. NOTE : MATERIAL SHALL BE
INSPECTED BY RDSO
Supply of Unwired Tag blocks 200 way
to RDSO spec.no IRS-S-77/2006
32 (Rev.1) Drg no.SA 24751 NOTE : 32 2 Numbers 32000.00 At Par 64000.00
QTY.UNIT TO BE READ AS system (32
fuses per system)
Schedule Totals 4284025.87
%
Schedule B1-SOR ITEMS - LABOUR PORTION (Item Directory - Not Applicable) 10371460.26 45.00 15038617.38
Above

CHAPTER -19 CABLE LAYING Final

1 1901 16 Kilometre 994.00 At Par 15904.00
location survey of cable route and final
preparation of cable route plan as per

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 13 of 27

technical specification.
Excavation of trench to a depth of
1200mm and width of 300m at bottom
in all types of soil(Normal soil/soft
soil/sandy soil except in hard morum /
rocky soils /bridges/ level crossings/
track crossings/ coil pits, ) as per
RDSO Sketch no SDO/CABLE
2 1902 8 Kilometre 51912.00 At Par 415296.00
LAYING /003 including marking of
cable alignment, clearing of jungle,
bushes, trial pits if required, refilling
with excavated soil, ramming and
consolidation after laying of cables
complete to the finished item of work
as directed by supervisor in-charge.
Excavation of trench to a depth of
1200mm and width of 300m at bottom
in hard morum soil as per RDSO
Sketch no SDO/CABLE LAYING /003
including marking of cable alignment,
3 clearing of jungle, bushes, trial pits if 1903 8 Kilometre 67092.00 At Par 536736.00
required, refilling with excavated soil,
ramming and consolidation after laying
of cables complete to the finished item
of work as directed by supervisor in-
charge.
Cutting of rock to a depth of 200 mm
and width of 200 mm where rock is
visible from surface to a depth more
than 300 mm up to 550mm,
excavation of trench with width
300mm above rock concreting
200mmx200mm after laying of cable
with 1 cement: 2 sand : 4 graded
stone aggregate 20mm nominal size
and curing of concrete to the required
4 number of days, refilling with 190501 1100 Metre 241.00 At Par 265100.00
excavated soil ramming and
consolidation except in bridges,
culverts, level crossings, track
crossings, cable pits, rocky soil
including marking of cable alignment,
clearing of debris etc., complete to the
finished item of work as directed by
site in-charge. Drg No.SK/CN/NEW/3.
All the material is to be arranged by
contractor.
When rock is visible for more than 0.5
metre and up to 0.8 metre from the
ground level, excavating the trench
5 minimum 0.5 metre and maximum 0.8 190502 800 Metre 200.00 At Par 160000.00
metre, laying of cable and concreting
200 mm x 200 mm over the rocky
surface after levelling with soil/sand
Track crossing by horizontal boring
method based on the drawing
no.DRM/J/6735 dated 7-8-03
(enclosed) and as advised by the
engineer at site. This includes the
6 supply and insertion(pushing) of GI 1907 1800 Metre 1403.00 At Par 2525400.00
pipe (80mm) confirming to IS.1239
heavy class in the bore drilled with the
coupler between two pipes. All the
joints of casing pipes should be tight
and leak proof.

Trenching under Rails for crossing the

track(Track crossing) and refilling of
trenches as per RDSO drawing
No.SDO/CABLE LAYING /009. The
track crossing shall be done at right
angles. The depth of cable trench shall
7 be 1.2 Mtr. below the rail flange. The 1908 600 Metre 141.00 At Par 84600.00
depth between top cable and the level
of rail flange of the rail shall never be
less than 1.0 Mtr.. The ballast shall be
Stored separately while making the
trench and the earth soil shall be
stored separately. while re-filling the
trench, the earth soil has to be filled

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 14 of 27

first to the ground level and the ballast

has to be properly put in the track.
this work has to be done under
supervision of supervisor of S&T and
supervisor of P.Way
Breaking of metal/ tar road and
refilling after laying the cables as per
drawing no.SDO/CABLE LAYING/010.
8 1909 200 Metre 142.00 At Par 28400.00
The surface of the road shall be
concreted to match with the old
surface
Laying different type cables in the
9 trench. Termination covered 1910 140000 Metre 5.00 At Par 700000.00
elsewhere.
Excavation of square coil pit up to a
depth of 1 Mtr. X 1.5 Mtr. For
providing coil at location box, point,
10 signals etc., This includes back filling 1914 140 Numbers 181.00 At Par 25340.00
and ramming of trench / pit after
laying the cable and consolidation of
soil.
Supply and laying of split DWC pipe.
(1) Supply & laying of DWC split pipe
of 120/103mm dia, 2 meter long in
11 already dug cable trenches has per 191701 3500 Metre 232.00 At Par 812000.00
Drawing No.SK.9/11. The unit of RMT
means two split pipes of 1 meter each.
Inspection : RITES
(2) Supply & laying of DWC split pipe
of 250/217 mm dia, 2 meter long in
already dug cable trenches has per
12 191702 3000 Metre 761.00 At Par 2283000.00
Drawing No.SK.9/11 .The unit of RMT
means two split pipes of 1 Mtr each
Inspection: RITES
Supply & Laying of G.I Pipes 50mm
dia. medium quality to specification
IS.1239 (part-I) 1990 and galvanised
to specification IS.4736-1986 On
bridges , culverts, trench with channel
ramps on either en of the
13 1918 120 Metre 254.00 At Par 30480.00
culvert/bridges. Clamping
arrangement with MS brackets for
fixing of GI pipes on bridges/culverts,
small holes of 5mm are to be drilled on
the pipe before laying of the pipes.
(Inspection by Consignee)
Supply & Laying of G.I Pipes 100mm
dia. medium quality to specification
IS.1239 (part-I) 1990 and galvanised
to specification IS.4736-1986 On
bridges , culverts, trench with channel
ramps on either end of the
14 1919 180 Metre 341.00 At Par 61380.00
culvert/bridges. Clamping
arrangement with MS brackets for
fixing of GI pipes on bridges/culverts,
small holes of 5mm are to be drilled on
the pipe before laying of the pipes.
(Inspection by Consignee)
Provision and laying in position cement
concrete of 1 cement:3 sand:6 graded
stone aggregate of 20mm normal size
excluding cost of cement, centering
15 and shuttering ( including 192301 6 cum 2085.21 At Par 12511.26
transportation of all the material) . (1)
Plain cement Concrete of 1 cement: 3
sand : 6 graded stone aggregate
20mm nominal size
Supply of Cement 53 graded of 2.2
16 192302 14 Quintal 460.00 At Par 6440.00
quintals per Cum of concrete
17 Centering and shuttering 192303 80 Sqm 291.15 At Par 23292.00
Jungle cutting along with the cable
18 1925 12000 Metre 4.00 At Par 48000.00
route
CHAPTER -20 LOCATION BOX
Installation in location box at RE
cuttings and wiring of all power supply
19 2002 4 Numbers 375.00 At Par 1500.00
equipments viz., Chargers,
Transformers, Trans-rectifiers etc., as
per the detailed specifications.

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 15 of 27

Test lamp arrangement in LBs/RE

cuttings.(Auto mobile handle type.
20 2003 70 Per Unit 119.00 At Par 8330.00
NOTE : PER UNIT TO BE READ AS PER
LOCATION
Supply and fixing of 20mm thick teak
wood planks for Keeping Equipment in
the Full Box after applying two coats of
21 wood primer. The approximate size of 2008 70 Per Unit 490.00 At Par 34300.00
the flank is 940mmx20mmx300mm
NOTE : PER UNIT TO BE READ AS PER
PLANK
Cable termination including fixing
Per
22 terminals, fuses, LDs etc,. Meggering 2014 70000 7.00 At Par 490000.00
Conductor
the cables and recording the readings.
Numbering location box as per
standard practice and writing all
termination particulars inside the
location box as per details. This
23 includes all main and tail cable 2015 133 Numbers 280.00 At Par 37240.00
particulars, writing of cable numbering
of cables, polishing teak wood boards
in two coats and painting hard wood
shelves in two coats of black enamel.
Fixing relay bases, wiring in location
boxes, bunching, fixing of relays as per
circuit diagram. This includes fixing of
24 condensers, resistance, 6 way / 1 way 2016 80 Per Relay 156.00 At Par 12480.00
terminals/ WAGO, ND type fuses, LED
indicators for fuses as per type fuses,
LED indicators for fuses.
CHAPTER -21 EARTHING Earthing and
25 2102 600 Per Unit 21.00 At Par 12600.00
soldering of cable armour.
CHAPTER - 22: SIGNAL RELATED
ITEMS Strengthening of foundations of
signals, Full/Half location boxes, by
carrying out the earth work around the
26 foundation, ramming of the earth, 2207 100 Numbers 2813.00 At Par 281300.00
caring out masonry work from bottom
of earth work using country stones and
cement masonry to prevent the earth
from slipping down the bank.
Provision of SCREEN on signals when
they fall within 2 meters from the live
conductor by expanding metal
( size.20mm x 60mm strand 3.25 mm
wide and 1.6mm thick ) as per the
27 instruction of site engineer in-charge, 2206 12 Numbers 3058.00 At Par 36696.00
This includes supply of all materials
including earth electrode and earthing
arrangements. Drg. No.RE/S&T/S.
16/T/SK/26.A.85 & Drg.
No.RE/S&T/sig/Tender/Alt.A/SK/13/85.
CHAPTER-23 : POINT MACHINE
RELATED ITEMS Fixing of point
machines on PSC/Wooden sleepers as
per standard drawing. Wiring as per
28 2301 46 Numbers 4308.00 At Par 198168.00
circuitry includes fixing & wiring of
point contactor unit frames and
controlling relays . Includes fixing of
crank handle ward plate.
CHAPTER - 24 : TRACK CIRCUIT
RELATED ITEMS Wiring of Track
circuits feed end, relay end complete
with TLDs, batteries, chargers, track
relays, double lead wires, providing
29 insulation etc,. connected with track 2401 85 Numbers 1004.00 At Par 85340.00
commissioning of track circuit
including provision of bracket for TLD
covers and painting. Anti-tilting
arrangement has to be done for track
relays, chargers & batteries.

Drilling of holes 7.2mm on web of the

rail , providing bond wires with PVC
coated wire rope. (Bond pins single
30 grove have to be supplied by 2404 2000 Per Unit 16.00 At Par 32000.00
contractor - Wire rope for bonding is
covered under supply portion ).
NOTE : PER UNIT TO BE READ AS PER

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 16 of 27

RAIL JOINT
CHAPTER - 25 : SIGHTING BOARD
&CALLING BOARDS Fabrication,
Supply and fixing of CALLING ON
instruction boards, STOP boards with
engineering grade reflective sticker of
size 600X900X1200 mm GI sheet, with
31 MS angle of 75X75X6 mm with 6 2502 4 Numbers 3549.00 At Par 14196.00
meter length including paint,
excavation of pit and concrete
foundation etc..as per the instructions
of sight in-charge. All necessary
materials to be arranged by the
contractor).
CHAPTER - 26 : INDOOR WORKS
Providing crank handle box, wiring,
32 2605 7 Numbers 3848.00 At Par 26936.00
testing as per technical specification
including concealed wiring in the wall .
Manufacturing and fixing of glass
fronted box ( key box) made out of
33 2606 2 Numbers 255.00 At Par 510.00
teak wood of size 10 inches x 16
inches.
Erection of Relay rack
1way/2way/4way with scaffolding
suitably concreting tri-pod bases using
J-bolts, fixing rack supporting of size
50x50x6 mm on to the wall. Reel
34 insulators are to be provided for 2611 1 Numbers 341.00 At Par 341.00
insulating the rack from the scaffolding
& tri-pod bases. ( payment based on
number of equivalent 1 way relay
racks). NOTE : NUMBERS TO BE READ
AS PER ONE WAY RACK
Fabrication and supply of MS frames to
suit Q- series relays to accommodate 6
No. in each set as per Drg.No.
B.SG.CN. MISC.9.98 duly drilling
35 required holes for relay bases (All 2613 10 Numbers 294.00 At Par 2940.00
materials such as frames, bolts, nuts
and washers to be supplied by the
contractor) (Only Relay bases will be
supplied by the Railways).
Fixing relay bases on the relay frames
erected in Relay Room, Wiring of all
types of relays by drawing various
sizes of wires/multicore cable, fixing
fuses, condensers, resistances, LEDs
etc and wiring duly soldering the same
as per approved circuit diagram,
testing point to point before soldering
and after soldering, bunching and
lacing as per detailed technical
specification.Different colour codes and
sizes of wire to be used as per
standard practice. This also includes,
provision of all PVC sleeves required to
be provided. Copper lugs to suit to
16/02 wire and neat bunching, lacing
with Modi Nylon / Twine thread and
36 using PVC dotted tape with buttons 2614 40 Numbers 174.00 At Par 6960.00
were required. This also includes
soldering all the wires in the relay
room with Rosine core of IS Spec.
1921 @40<37@Tin and 40% Led).
Soldering should be done as per
standard practice. This also includes
inserting the clips, point to point
testing as per the circuit diagram and
plugging relays to Relay bases (except
Inter-cables, relays other materials
such as Rosine core, flux, nylon
thread. PVC dotted tape should be
supplied by the contractor). Point to
point testing should be done in the
presence of Engineer-in-charge as
instructed in two stages, one before
soldering and the other after soldering.
Fixing of the following on pre-erected
relay racks. Fixing of approximately

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 17 of 27

200 nos of 6 way/ 1 way terminal

block horizontally on 6mm Hylam
sheets which in turn to be fixed to rack
37 with all supports as per instructions of 261501 4 Set 479.00 At Par 1916.00
SSE incharge. Materials such as bolts,
nuts and supporting flats to be
supplied by the contractor only.
Indoor Painting as per technical
38 2617 2 Lumpsum 3009.00 At Par 6018.00
specification for 2/3 road stations.
Provision of one skilled and 2 unskilled
staff round the clock to attend to
teething trouble of the installation
along with SI/CSI after the installation
39 2623 4 Month 43437.00 At Par 173748.00
has been brought into commissioning.
The work includes routine
maintenance, failure restoration as per
the direction of the SI/CSI.
Fabrication, fixing of required
configuration of key in point machine
40 2624 46 Numbers 82.00 At Par 3772.00
for grouping of crank handle of point
machines.
Installation, testing and commissioning
of Data logger which includes the
software configuration needed,
validation, taking test print, for
networking & transfering the data to
41 2610 1 Numbers 24280.00 At Par 24280.00
nominated location for monitoring and
changing of EPROMS if any as per the
instruction of site in-charge, including
alterations data base in HQ/SSE office
where ever required.
CHAPTER-27 : TRANSPORTATION -
Transportation of materials from any
Stores to Site and vice-versa including
42 270101 20000 Per Trip 7.31 At Par 146200.00
loading and nloading. (A)Lead upto 50
Kms NOTE : QTY.UNIT TO BE READ AS
PERTONNE/PERKM
Transportation of materials from any
Stores to Site and vice-versa including
43 loading and unloading. (B)Lead above 270102 10000 Per Trip 4.80 At Par 48000.00
50 Kms NOTE : QTY UNIT TO BE READ
AS PER TONNE/PER KM
CHAPTER - 28 : POWER SUPPLY :
44 Initial Charging of Secondary Cells:- 2 2802 260 Numbers 220.00 At Par 57200.00
volts 80 AH
CHAPTER - 33: DOCUMENTATION
Design of cable route plan, cable core
chart, location box particulars, panel
particulars, fuse particulars, track
bonding diagram, numbered wiring
diagrams, relay index, contact
analysis, posting of contacts in wiring
diagram to be supplied by Rlys,
surveillance panel particulars, data
logger particulars, K rack, rack details,
resistor, condenser particulars, power
45 equipment wiring, power equipment 3301 2 Numbers 83295.00 At Par 166590.00
foot print diagram, etc as per
requirement. Supply of 6 sets of final
hard copy of the approved circuit
diagrams and the documents
mentioned above along with contact
analysis in A2, A3, and A4 sizes as
required with 1 set of prints on tracing
film and a soft copy on compact disc
(CD) to be supplied. (Arranging rexin
cloth bound booklets and binding for
large and small sizes of drawings).
CHAPTER - 34 - ALTERATIONS:
Shifting of existing cables from old
location boxes / relay room to new
location boxes / new cable termination Per
46 3402 1800 8.00 At Par 14400.00
racks, terminating the conductors in Conductor
serial order, bunching neatly for
matching the circuits with new cables
as per cable plan.

Carrying out circuit alterations in the

existing location boxes as per the new

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 18 of 27

circuits which require excavation and

releasing unwanted cables from the
location box and taking new cables
47 inside the location, clamping of new 3403 35 Numbers 612.00 At Par 21420.00
cables, filling the location box with
standard up to the bottom of location
and plastering.
CHAPTER - 32 - RELEASING OF S&T
GEARS Releasing of the following
equipments without causing damage,
stacking neatly at a centralised place
48 near the site of work as shown by the 3204 40 Numbers 148.00 At Par 5920.00
in charge, and handing over the same
to the Stores depot as per the
inventory made. Releasing of location
boxes Full/Half/sheet iron
Releasing of Warning Boards/stop
49 3205 6 Numbers 252.00 At Par 1512.00
boards
50 Releasing of block counter 3207 2 Numbers 306.00 At Par 612.00
51 Releasing of block instrument 3208 2 Numbers 307.00 At Par 614.00
Releasing of existing Axle Counter field
equipment (transmitters 2 No. receiver
coils 2 No.) on the rails at the
entry/exit track circuits without
causing any damage. Excavating the
under the track for removing track
52 devices, connecting cables and duly 3212 5 Set 702.00 At Par 3510.00
covering the cable duct. Disconnecting
and removing of Amplifier (electronic
junction box and other associated
equipment from the location box and
transporting to a central location for
accountal.
Releasing of colour light signal 1/2/3/4
53 3213 25 Numbers 532.00 At Par 13300.00
way complete.
Releasing of shunt signals ground type
54 3214 4 Numbers 141.00 At Par 564.00
complete.
Releasing of Electrical point equipment
55 3215 24 Numbers 213.00 At Par 5112.00
complete.
Releasing of complete equipments and
56 materials in battery, equipment rooms, 3217 1 Lumpsum 2577.00 At Par 2577.00
relay rooms and SM's office.
Installation and testing of block
proving by digital axle counter system.
The work consists of: a) Fixing of axle
counter track device consisting of Tx-
Rx coil assembly for each detection
point drilling holes in the rails as per
the marking given by the site in
charge. b) Fixing of rails deflector
plates on either side of each detection
points as per the marking given by the
57 3602 1 Set 15210.00 At Par 15210.00
site in charge. c) Fixing of evaluators
inside pre-erected location boxes on
the nominated planks along with VR
assembly duly providing anti-vibration
arrangements as per the instructions
of site in-charge. d) Routing cables
from Tx/Rx coil assembly through pre
laid GI pipe arrangements of track
crossing and entering the location box
and termination.
58 Commissioning charges for BPAC. 3603 1 Set 10081.00 At Par 10081.00
TELECOM RELATED ITEMS :
59 Installation of 2 wire DTMF Selective 3501 4 Numbers 622.00 At Par 2488.00
Calling Telephone with power supply.

Straight through / derivation

with/without transformer joints:
Installation Thermoshrinkable jointing
kits for straight through I derivation
joints for LC gate, pump houses etc
60 3502 10 Numbers 979.00 At Par 9790.00
where VF transformers are not
required and derivation joint by using
2T transformer (to be housed in the
joint). This includes tapping of
nominated Quad at a specific location
shown by the Railway Engineer at site

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 19 of 27

to the jelly field cable already laid. All

material including vulco tapes except
thermo shrinkable jointing kit shall be
supplied by the contractor. (Refer
Annexure for instructions on cable
jointing). NOTE : QTY. UNIT TO BE
READ AS PER JOINT
Installation and commissioning of 4
Wire way station control equipment as
detailed below: a) The way station
equipment & Power supply unit are to
be mounted on a rack as per Drg.No.
COREIS&TIALD /SK/436/95. b) The
61 internal wiring should be wired 3505 4 Numbers 2651.00 At Par 10604.00
between VF Repeater/VF Transformer
bay and MS Angle rack then to be
extended to Dy.SS/ASM Table as per
drawing shown in the sketch (All the
wiring materials are to be provided by
the contractor).
Testing and commissioning of the
system: This work involves the Testing
of Underground six quad cable in each
repeater section after laying and
jointing. These readings to be recorded
62 and supplied to Railway Engineer. This 3506 3 Numbers 2271.00 At Par 6813.00
involves all the tests to be carried out
such as measurement of loop
resistance, insulation test, frequency
attenuation, cross talk and noise level
etc.
Laying of HDPE duct 40/33 mm dia in
63 the trenches and in protective works 3508 1 Kilometre 4956.00 At Par 4956.00
already provided.
Fabrication, installation and fixing of
emergency socket post, box and
emergency socket as per the drawing
No. OH E/1 .6A/94 (enclosed). These
64 3510 2 Numbers 1469.00 At Par 2938.00
emergency socket posts to be fixed
along with the cable route at an
interval of not more than 1 Km. As per
the dia
Supply and installation of 45mmx
45mm PVC channels for drawing
65 switchboard cables at OFC cable huts 3511 100 Metre 66.00 At Par 6600.00
and at stations as indicated by Railway
Engineer at site.
Supply and fixing of different sizes of
PVC casing /Pipes as required by
Railway at site by fixing /clamping to
the wall for indoor wiring purposes.
The material required carrying out the
66 3512 200 Metre 32.00 At Par 6400.00
wiring such as soldering, lacing,
casing, fixing clamps; screws etc are
to be provided by contractor on his
own cost. Switchboard cables are
supplied under different item.
Installation of 100/50/20 pair Krone
terminal Box as supplied vide NS items
on hard wood plank of size 8"x13"x1"
67 plank and wiring. Hard wood plank and 3513 2 Numbers 114.00 At Par 228.00
other materials like screws, bolts etc
to be supplied by the contractor at his
own cost.
Documentation: 1). Original
documents of Cable laying particulars-
cable laying/ testing/ commissioning
will be handed over to Executive
Engineer-in-charge after all the works
are over.2). Based on above 6 No.
Documentation sets in A4 size shall be
68 prepared covering the following items 3514 6 Set 167.00 At Par 1002.00
broadly-Cable laying particulars-, Block
section measurements, EC/LC gate
telephone particulars, Cable route
plan, Tapping diagram, Standard
schematic diagram for EC socket]
cable termination, layouts at way
station etc in programmed CD's-2No.

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 20 of 27

Blowing of armored optic fiber cable

(OFC Cable supplied by Railways) into
the duct supplied in supply portion by
using blowing machine and associated
works. Before blowing the duct
69 integrity shall be tested. If any defect 3518 1 Kilometre 7382.00 At Par 7382.00
is found during duct integrity test, the
entire length of HDPE duct from one
chamber to another chamber is to be
replaced by the contractor at free of
cost.
Supply and Installation of OFC joint
enclosure and splicing of Optic fiber
cable (24 fibers) and testing as per
technical specification No. GR OJC-
2/02 Sept 2003. Supply of Splice
Enclosure (24 fiber) shall be of TVS
make Part No.1500-L18X-XX as per
70 3519 4 Numbers 6416.00 At Par 25664.00
Board specification of TEC and
Schedule of supply enclosed. All
materials including Fusion splicing
machine used for fiber splicing and,
OTDR for testing and other testing
materials if any shall be arranged by
the contractor.
Testing of fibres by splicing all 24
71 3522 2 Lumpsum 15818.00 At Par 31636.00
fibres (long haul)
Testing of fibres between short haul
station in both direction after splicing
the required fibres. Testing of OFC
72 3523 3 Lumpsum 5273.00 At Par 15819.00
system complete with electronics,
battery banks and handing over for
Maintenance to Open Line / RAILTEL.
Fixing of 12 pair weather proof C.T.
Box WAGO type and termination of 6
73 quad jelly filled cable on teak wood 3524 4 Numbers 217.00 At Par 868.00
plank of size 375mm x 250 mm x 20
mm thickness
Operation of any other SOR Items
74 ANYSOR 1 Lumpsum 200000.00 At Par 200000.00
from Chapter-19 TO 27
Schedule Totals 15038617.38
Schedule B2-NON SOR ITEMS - LABOUR PORTION (Item Directory - Not %
6129220.19 44.00 8826077.07
Applicable) Above
Electronic Interlocking Supply,
fabrication, installation and fixing of
panel operator consol with
arrangement to fix upto 55" VDU's -
2Nos. Reset boxes, and other S&T
gadgets. This shall be made of not less
1 than 18mm thick playwood/novopan or 1 1 Lumpsum 244641.00 At Par 244641.00
better materials with storage facility of
approved colors with contractors'
materials, lead, lift and manpower as
per the instructions of engineer in
charge and as per the enclosed
drawing. (Inspection by Consignee)
EMI Earthing arrangements for EI
(central building) including End
Goomties for Object controllers as per
RDSO Specification as required for EI
system as per Rly board
Lr.No.2010/Sig/SGF/EI (Ansoldo)
dated 22.06.2011 and RDSO TAN No.
2 2 1 Per Unit 200000.00 At Par 200000.00
STS/E/TAN/3006 dated shall be
followed. All materials shall be
supplied by contractor. MF earthing
materials shall be inspected by RITES
and shall be procured through RDSO
recommended firms. NOTE : PER UNIT
TO BE READ AS PER LOCATION
Installation of Embeded Industrial
Grade Fan-less VDU of both operating
3 3 3 Lumpsum 50000.00 At Par 150000.00
dual VDU and Maintainer VDU with all
accessories.
"Supply and installation of active
lightning arrestor of class-A for
building protection of ERICO 3000
Make or similar with the approval of

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 21 of 27

engineer in-charge which shall work on

ming principle along with counter as
per technical specification enclosed.
4 Installation to be done by OEM 4 1 Numbers 315000.00 At Par 315000.00
authorized firm/Vendors. NOTE :
MATERIAL SHALL BE INSPECTED BY
RITES
Preparation of Station Working Rules,
CRS papers etc as practice in Railways
5 5 2 Per Unit 11484.00 At Par 22968.00
for yards/LC Gate/IBH including Xerox
(Per Unit=Per application)
Supply ,transportation and installation
of Cable termination rack similar to
M/s. Medha Servo Drives Pvt. Limited
or similar to suit other EI racks with all
fixtures ,Supporting Angles, Triangle
6 6 3 Numbers 27280.00 At Par 81840.00
Bases, Insulators, Din Rails duly fixed
on rack with powder coated and colour
of rack to be matched with the relay
rack supplied by the OEM of E.I and as
directed by engineer in-charge at site.
Supply, Installation and commissioning
of Hand held/Desk top work station
complete as per specification or better
with necessary cables, programmes,
software for programming and trouble
shooting and commission of EI. Intel
corei7 4790/8GB Ram/1TB HDD/19.5"
wide, windows8.1 pro or latest, key
board, optical mouse, DVD RW & Hard
disc drive from
Seagate/Maxtor/Thoshiba industrial
chassis with 400W ATX power supply,
DVD writer/Reader 100 mbps
Eathernet NIC cardon
board/PCI ,wireless LAN'G' card in
7 built, 4USB ports, one serial port , 7 1 Numbers 64487.00 At Par 64487.00
multi media key board from
Logitech /Microsoft, High resolution
optical mouse from Logitech/Microsoft
high quality audio on board, creative
2.1 speaker, 56kbps modem, genuine
Microsoft windows 8.1professional OS
with recovery CD, one head phones
port, make : Dell/Sony/Hp latest, &
antivirus licensed software with 3years
validity from kaspersky, norton, MC
Afee total system should have 3years
warranty. UPS battery back up with
700 VA of APC or similar. NOTE :
MATERIAL SHALL BE INSPECTED BY
CONSIGNEE
Signalling item: Excavation of pit,
casting concrete foundation and
erection of apparatus case full size as
per Drg. No. SK/CN/1/89/A/1 and
fixing of 1 No.of 'E' type lock for the
front door, fixing of one hylam sheet of
1000mm X 940mm X 10mm thickness
and painting the apparatus case inside
and outside with one coat of redoxide
8 8 115 Numbers 9875.00 At Par 1135625.00
and two coats of aluminium paints
(foundation bolts and nuts,' E' type
lock, cement, river sand, stone jelly of
size 20/20mm, hylam sheet of size
1000mm X 940mm X 10mm, paints,
varnish, fixing bolts and nuts and all
other miscellaneous material required
for the work shall be supplied by the
contractor).

Excavation of pit, casting concrete

foundation and erection of apparatus
case half size as per Drg.
No.SK/CN/1/89/B/1, fixing one 'E' type
9 lock for the front door and latching 9 23 Numbers 6967.00 At Par 160241.00
arrangements for the back door and
fixing of one hard wood shelf plank
37mm thick and painting the
apparatus case inside and outside with

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 22 of 27

one coat of redoxide and two coats of

aluminium paints (foundation bolts and
nuts, E type locks, cement, river sand,
stone jelly of size 20/20mm, hardwood
plank of 37mm thick, paints, varnish,
fixing bolts and nuts and all other
miscellaneous material required for the
work shall be supplied by the
contractor).
Excavation of pit, casting concrete
foundation as per Drg. No.
SC/N/CN/62 A/1 using metallic
templates, for erection of Colour light
Signals upto 4 aspects (foundation
10 10 32 Numbers 5008.00 At Par 160256.00
bolts, cement, river sand, stone jelly of
size 20/20mm dia and all other
miscellaneous materials required for
the work shall be supplied by the
contractor).
Erection of surface base, signal pole,
mounting of Colour Light Signal upto 4
aspects complete on signal pole /
offset bracket, (for LED / filament
bulbs) with lenses, triple lamp holder,
filament switching units, CLS
transformers, current regulators
(whichever is applicable), fixing of
ladder with platform complete and
concreting of ladder shoe, fixing of
number plates, marker board, lenses
guard, fixing of speed Limit board,
whichever is necessary, termination
tail cables, wiring of signal unit with
PVC wire 3/0.75mm copper, provision
of EWS locks, and painting of one coat
of redoxide and two coats of
aluminium/enamel paints. When the
aspect is fixed on offset bracket using
'U' bolts and nuts, a through bolt shall
11 be provided by drilling of hole in the 11 32 Numbers 5501.00 At Par 176032.00
signal pole to prevent the offset
bracket from sliding down. Item
Contd., (Supply of surface base, offset
bracket, CLS pole, CLS aspect
complete, ladder with shoes and
platform, Speed limit board, LED
aspects, current regulators, lamp
holders, lamps, filament switching unit
and CLS transformer is not covered in
this schedule). ['U' bolts and nuts,
through bolts and nuts, cement, stone
jelly 20/25mm dia, river sand, Signal
Colour Rings, wire PVCV 3/0.75mm
copper, lens-guard, all fixing bolts and
nuts, lead wood, paints PVC/Nylon
sleeves, enamelled number plates,
enamelled marker boards, EWS locks,
and all other miscellaneous materials
for the work shall be supplied by the
contractor).
Excavation of pit and casting concrete
foundation as per Drg. No.
SC/N/CN/62 B/1 using metallic
templates, for erection of ground type
12 colour light signal. (Foundation bolts 12 8 Numbers 2519.00 At Par 20152.00
and nuts, cement, river sand, stone
jelly of size 20/25mm and all other
miscellaneous materials for the work
shall be supplied by the contractor).

Erection of Ground type shunt signal

complete including surface base, signal
pole, LED aspects/Lenses, bulbs with
holders (whichever is applicable),
13 fixing of lens guards, number plate, 13 4 Numbers 2097.00 At Par 8388.00
termination of tail cables, wiring of
signal unit with PVC wire 3/0.75mm
copper, provision of EWS locks and
painting of one coat of redoxide and
two coats of Aluminium /.enamel

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 23 of 27

paint, (Supply of Ground type shunt

signal complete including surface base,
signal pole, LED aspects, holder, bulbs
and lenses is not covered in this
schedule). [Wire PVC 3/0.75mm
copper, lens guards, EWS locks,
enamelled number plates, bolts and
nuts, lead wool, paints and all other
miscellaneous materials shall be
supplied by the contractor).
Fixing of junction type route indicator -
1 way to 6 way - complete / fixing of
additional limb to the existing route
indicators, termination of tail cables,
wiring as per approved circuits
diagram using wire PVC 3/0.75mm
copper, provision of required number
of EWS locks, wire mesh and painting.
(Supply of junction type Route
14 14 5 Numbers 1539.75 At Par 7698.75
Indicators - complete and additional
limb is not covered in this schedule).
[3/0.75mm wire PVC fixing bolts and
nuts, EWS locks, wire mesh,
PVC/Nylon sleeves, paints and all other
miscellaneous materials shall be
supplied by the contractor] - Fixing
and wiring of direction type route
indicator -1 w ay
Fixing and wiring of direction type
15 15 5 Numbers 1824.00 At Par 9120.00
route indicator - 2 way
Fixing of offset bracket using U-bolts
and nuts erection of posts type shunt
signal termination of tail cables,
provision of EWS lock and painting of
one coat of red-oxide and two coats of
16 16 10 Numbers 1613.25 At Par 16132.50
aluminium / enamaled paint. The work
also includes drilling suitable holes on
the CLS post and provision of a
through bolt with nut to prevent the
offset bracket from slipping down.
Fixing of Offset brackets using 'U' bolts
and nuts, erecting of Calling On
Signals/'A' marker lights, termination
of tail cables and wiring using wire PVC
3/0.75mm copper, provision of EWS
lock, number plates/ markers boards
and painting. The work also includes
drilling suitable holes on the CLS post
and provision of a through bolt with
nut to prevent the Off-set bracket from
17 17 22 Numbers 1427.25 At Par 31399.50
slipping down. (Supply of Calling On
Signal / 'A' marker light, LED aspect /
holders and bulbs and off set brackets
is not covered in this schedule). ['U'
bolts and nuts, through bolts with nut,
wire PVCV 3/0.75mm copper, EWS
lock, Enamelled number plates, wire
mesh, PVC/Nylon sleeves, paints and
all other miscellaneous materials shall
be supplied by the contractor].
Supply, painting and fixing of cable
18 Gland Plate for full / half GKP box as 18 140 Numbers 533.00 At Par 74620.00
per site requirement.
Supply of approved quality of paint
manufactured by Asian/British/Johnson
and Nicholas accepted by DSTE/ASTE
and Painting of all S&T gadgets in two
19 19 140 Sqm 78.00 At Par 10920.00
coats duly scarping the rust as
directed by SSE/SE at site, the colour
to be used as per standard practice
and as directed by SSE/SE at site.
Supply and fixing of Netlon wire mesh
of all windows and ventilators as per Square
20 20 100 291.00 At Par 29100.00
instructions of Engineer-in-charge Foot
including labour charges.
Installation of Earth Leakage detector
21 21 1 Numbers 8000.00 At Par 8000.00
12 channels.

Shifting of existing working functions

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 24 of 27

like signals/Shunt/Calling
on/Points/Track circuits etc. from old
cable to new laid cables carefully
22 22 30 Per Unit 1460.00 At Par 43800.00
without affecting the traffic under
disconnection/blocks. (NOTE : PER
UNIT TO BE READ AS PER FUNCTION)
Implementation and testing per station
23 23 2 Station 5000.00 At Par 10000.00
of point reversal alaram.
Transporting and supply and
installation of Concrete (RCC) route
indicators at intervals of 50 meters as
per technical specification. They should
be of standard RCC with letters " one
24 24 400 Numbers 807.00 At Par 322800.00
side "SCR" and the other side "S&T
cables" as per drawing SK 12/10 of
RVNL/SC . In case of telecom quad
cable joint locations it shall be painted
with red color.
Arranging of skilled and un skilled
workers with required tools during
point blocks for removal of S&T assets
25 25 10 Point 3178.00 At Par 31780.00
to give way for T28 Machines and
refixing the removed assets after
insertion/removal of point.
Provision of Security guards round the
clock beet from UP Home Signal to DN
Home Signal to avoid theft of
26 26 360 Shift 434.00 At Par 156240.00
signalling gadgets in 12hour shift. Only
Night shifts from 06.00 PM to 06.00
AM
a)Fabrication, supply and internal
installation of NI panel of size
27 27 1 Numbers 8333.00 At Par 8333.00
12"x24"x12" made in 18 gauge MS
sheet as per the spec.
29 c)Relay fixing and wiring 29 50 Numbers 174.00 At Par 8700.00
d)Supply of LED holders with LED of
30 30 100 Numbers 12.00 At Par 1200.00
size 5mm .5W
e)Fixing of LEDs along with Jewels,
Resistors, Sleeves duly drilling holes
and soldering including drawing of
31 31 100 Numbers 12.00 At Par 1200.00
wires, bunching and lacing. (All
materials to be supplied by the
contractor).
f)Preparation of Contact Analysis for
32 'Q' style relays as per detailed 32 50 Numbers 14.00 At Par 700.00
technical specification.
33 g)Termination of cable conductors 33 500 Numbers 7.00 At Par 3500.00
h)Condensers 50V, 470Mfd -20Nos,
Condensers 50V, 1000Mfd-20Nos, wire
34 wound resistance -100ohms 10W - 34 2 Set 2562.00 At Par 5124.00
20Nos, Diodes BY 127 -10Nos & PVC
insulation tape of 25mtr - 25No.
Fabrication, Transportation and fixing
of Aluminium ladder at site made of
aluminium angle size of 38mmX5MM
width 280mm, flat size with powder
coated colour as desired by engineers
in-charge at site and fixing of
25mmx5mm, drilling of suitable holes
35 for fixing of holes for fixing of Hylam 35 50 Metre 2865.00 At Par 143250.00
sheet 3mm thickness on ladder and
2nos of PVC trough 100mm with cover
fixed on Hylam sheet along the ladder
with all fixtures necessary ancillary
materials required for fixing to be
supplied and as directed by engineer
in-charge at site.
Fabrication,supply and erection of
conventional Earth to signalling
equipments -Excavation of earth and
providing earth pipe of size 50mm dia,
3.5mm thick 2.0 m. long G.I. pipe with
36 masonry tub constructed around at 36 180 Numbers 5100.00 At Par 918000.00
earth locations as specified by site
Engineer. Alternate layers of 30kgs-
chrcoal and 30kgs-common salt to be
filled in the pit while closing. The pipe
perforation etc., to be carried out as

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 25 of 27

per drawing No. SK 10/10.. The earth

pipe to be connected to the function
with cable as supplied by Railways.
The reading should be painted on the
masonry tub. The masonry tub of
400X400X450mm should be covered
with cement slab. ( All materials to be
transported and supplied by the
contractor except cable.)
Fixing of Housing of Rack multi-lamp
37 Route indicator single Digit 1-9 LED 37 3 Numbers 16000.00 At Par 48000.00
type
Supply of Designing and UV Printing of
station working order/Track bonding
diagrams TGL and MKR section of size
4ft x 3ft in molded aluminium channel Square
38 38 60 855.00 At Par 51300.00
with elegant and stainless steel star Foot
brackets for hanging arrangement.
Printing in UV print and designing in
corel draw package.
Installation, testing and commissioning
39 39 2 Set 56180.00 At Par 112360.00
charges of BPAC with dual sensor.
Communication arrangement and PA
system at Goompties as per the
40 40 8 Per Unit 1093.00 At Par 8744.00
instructions of site in-charge Note :
per unit to be read as per goompty
Supply and laying of RCC split pipe
41 150mm outer dia,2 mtr long in 41 300 Numbers 429.00 At Par 128700.00
trenches near traction sub station
Filling of sand in masonry cable duct
made in relay rooms and plastering
42 the same after taking all cables in side 42 3 Per Unit 12530.00 At Par 37590.00
NOTE : PER UNIT TO BE READ AS PER
LOCATION
Supply and Erection and Fixing of retro
reflective type BPAC warning boards of
size 600mm x 40mm x 6mm thickness
of 2.2 mtrs long.(retro reflective type
BPAC Warning boards, Angle, stone
43 43 14 Numbers 7118.96 At Par 99665.44
jelly of size 20/25mm dia, river sand,
cement, fixing bolts and nuts, paint
and all other miscellaneous materials
required for the work shall be supplied
by the contractor)
Labour assistance for SE/JE in day to
day works i.e checking the trench,
foundations, signals and points etc.
44 Carrying the tools & equipment etc. 44 120 Day 250.00 At Par 30000.00
during the course of execution of work
as per the instructions of concerned
SE/JE.
Fabrication and supply of wall mounted
maintainer's Tool Kit frame made out
of MS sheet 10 gauge with powder
coated as desired colour at site of size
1.5 Mtrs. Length X 0.8 Mtr. Width X
45 0.15 Mtr. Depth with all fixtures for 48 1 Numbers 13125.00 At Par 13125.00
mounting individuals, tools inside the
board and in front with Acrylic sheet
4mm thickness with locking
arrangements and all necessary
fixtures to fix on wall.
Supply and fixing of cross on the
signals (signal not in use) made of
hard wood of size 1000mm X 100mm
46 49 35 Numbers 328.00 At Par 11480.00
X 20mm (painted white as per Signal
Engineering Manual) and suitable
clamp made of MS flat.
Supply and providing of Polymeric
Positive Temperature Co-Efficient
47 50 200 Numbers 59.80 At Par 11960.00
Device self reseting type (PPTC)
suitable for Railway Applications-1.1.A.
Supply and fixing of Fire Extinguisher
48 52 2 Numbers 8840.00 At Par 17680.00
CO2 type (Capacity 5 KG)
Supply, Installation and
Commissioning of Block proving by
axle counter (BPAC) using Block panel
and UFSBI double line operation as per

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 26 of 27

RDSO specification No.IRS.S.105/2012

(Ver.0) with latest version or
RDSO/SPN/175/2005 Ver.1 or latest
and amendment including Spare cards.
Details as per enclosure. Make -
Deltron. (To be inspected by RDSO)
(1) Universal fail safe block interface
for single line complete with all
accessories as Per RDSO
Spe.No.IRS.S104/212(VER.0) with
latest version and amendment-2 No
(2)Relay rack with duly wired with due
locking and sealing arrangements
including relays (QNI-22NOs . ,QNAI-
06 Nos.; QLI-02 Nos ;Timer-01 No.
and wiring as wiring diagram
49 RDSO/S/32020(Latest Amdt.)-2 Nos 53 1 Set 957043.00 At Par 957043.00
(3)Single Line Block panel complete
with accessories as RDSO Drg No.
RDSO/S/32019 OR LATEST amdt-02
Nos (4)Block Telephone with
accessories as per RDSO Specn.No.
RDSO/SPN/191/2006-02 Nos (5) the
following spares shall be supplied
along with each pair (1)
Communication card-1 No(2) Modem
card- 1 No (3) CPU card- 1No (4)
Input card- 1 No (5) Reset Box - 1 (6)
Push button - 1 No for each type (7)
Key switch-1 No for each type (8)
Power supply unit-1 No (9) LED's for
various colour size -1 No's for each
colour (10) SAM unit if any
Installation and commissioning of
automatic media change over MODEM
Per Block
50 for use with Secondary/ back up media 55 1 17825.00 At Par 17825.00
Section
( 4 wire OFC VF channel from station
primary Mux/E1 Modem)
Laying of Double Walled Corrugated
Pipe(DWC)of REX or similar make of
51 120mm outer dia/103mm inner dia to 57 100 Metre 25.00 At Par 2500.00
IS spec.no.14930-part-II for under
ground cables of Six meters length.
Schedule Totals 8826077.07
Schedule C1-ELECTRONIC INTERLOCKING (NON SOR ITEMS) (Item Directory - %
13389054.00 39.50 18677730.33
Not Applicable) Above
Supply of Electronic Interlocking (Hot
Standby) for stations with Signalling
functions up to 125 units as per
Function table enclosed along with
15% spares, tools, manuals and
Instruments. E.I to be provided as per
RDSO Spec.No.RDSO/SPN/192/2005
1 1 1 Set 7832317.00 At Par 7832317.00
or latest .Note: Description of various
modules, sub assembly and other
accessories required as detailed in
explanatory note for the above work
with unit rate to be furnished by EI
manufacturer/contractor as annexure.
(Inspection by RDSO)
Incremental rate for signalling
functions in EI SYSTEM over and above
2 125 functions under item No 1 2 50 Per Unit 71250.00 At Par 3562500.00
(Inspection by RDSO)(Per Unit=Per
Function)
Supply of commercial grade operator
VDU of size 55" Full HD, HDMI/DVI
Connectivity, Inbuilt Speaker etc (For
3 3 2 Numbers 226320.00 At Par 452640.00
this item Prior approval of Engineer In
charge required in written).
(Inspection by Consignee)

Supply of fan less embedded industrial

grade computers ( Similar to Moxa
V2406 or better ) with all accessories
4 such as key board, mouse, antivirus 4 2 Numbers 257250.00 At Par 514500.00
etc. of industrial grade as per
approved Specification as
recommended by RDSO (TAN No.

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021
 Page 27 of 27

STS/TAN/3007 Version 1.0 or latest)

(Inspection by Consignee)
Installation, Wiring, testing, Soldering
of all EI equipments, earthing of EI
Equipment, Relay Racks and Power
5 5 1 Per Unit 633807.00 At Par 633807.00
Equipment etc. including supply power
cable and Documents/Manuals etc.
(Per Unit= Per EI)
Design and drawing for complete
6 indoor signalling work for new 6 1 Per Unit 243671.00 At Par 243671.00
PI/RRI/EI (Per Unit=Per PI/RRI/EI)
Commissioning of Electronic
7 7 1 Numbers 24619.00 At Par 24619.00
Interlocking system
Training of Railway Personnel in
installation, commissioning, testing,
trouble shooting and in diagnosing
8 8 1 Lumpsum 50000.00 At Par 50000.00
faults using diagnostic tools/flow
charts including supply of necessary
documents (60 Man days)
Training on application software for
designing, change in the logics and
converting it suitable for system and
loading the programme into the
9 9 1 Lumpsum 75000.00 At Par 75000.00
working system for alteration of
SIP/TOC. The training should be
comprehensive with complete
document (90 Man days)
Schedule Totals 18677730.33
Total Value 43294892.45 61691750.65
Rebate on Total Value
0.00
(%)
Net Bid Value 61691750.65

Item Breakup
No break up item added

https://www.ireps.gov.in/epsn/works/tds/publishLOAWorksLetter.do?Action=ViewPubli... 18-02-2021