HP Pavilion 13 Laptop PC

Maintenance and Service Guide

IMPORTANT! This document is intended for
HP authorized service providers only.
© Copyright 2018 HP Development Company, Product notice Software terms
L.P.
This guide describes features that are common By installing, copying, downloading, or
Bluetooth is a trademark owned by its to most models. Some features may not be otherwise using any software product
proprietor and used by HP Inc. under license. available on your computer. preinstalled on this computer, you agree to be
Intel, core, and Pentium are trademarks of Intel bound by the terms of the HP End User License
Corporation in the U.S. and other countries. Not all features are available in all editions of Agreement (EULA). If you do not accept these
Microsoft and Windows are U.S. registered Windows. This computer may require upgraded license terms, your sole remedy is to return the
trademarks of the Microsoft group of and/or separately purchased hardware, drivers entire unused product (hardware and software)
companies. and/or software to take full advantage of within 14 days for a refund subject to the
Windows functionality. Go to refund policy of your place of purchase.
The information contained herein is subject to http://www.microsoft.com for details.
change without notice. The only warranties for For any further information or to request a full
HP products and services are set forth in the refund of the computer, please contact your
express warranty statements accompanying local point of sale (the seller).
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.

First Edition: September 2018

Document Part Number: L33443-001

Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the
device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not
allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or
clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as
pillows or rugs or clothing, during operation. The device and the AC adapter comply with the user-accessible
surface temperature limits defined by the International Standard for Safety of Information Technology
Equipment (IEC 60950-1).

iii
iv Safety warning notice
Table of contents

1 Product description ....................................................................................................................................... 1

2 Getting to know your computer ...................................................................................................................... 5

Right side ............................................................................................................................................................... 5
Left side ................................................................................................................................................................. 6
Display .................................................................................................................................................................... 7
Keyboard area ........................................................................................................................................................ 8
TouchPad ............................................................................................................................................. 8
Lights ................................................................................................................................................... 9
Button and speakers ......................................................................................................................... 10
Special keys ....................................................................................................................................... 11
Action keys ........................................................................................................................................ 12
Bottom ................................................................................................................................................................. 13
Labels ................................................................................................................................................................... 14

3 Illustrated parts catalog .............................................................................................................................. 15

Computer components ........................................................................................................................................ 15
Cables ................................................................................................................................................................... 17
Display assembly components ............................................................................................................................ 18
Mass storage devices ........................................................................................................................................... 19
Miscellaneous parts ............................................................................................................................................. 20

4 Removal and replacement procedures preliminary requirements .................................................................... 21

Tools required ...................................................................................................................................................... 21
Service considerations ......................................................................................................................................... 21
Plastic parts ....................................................................................................................................... 21
Cables and connectors ...................................................................................................................... 21
Drive handling ................................................................................................................................... 22
Grounding guidelines ........................................................................................................................................... 22
Electrostatic discharge damage ........................................................................................................ 22
Packaging and transporting guidelines .......................................................................... 23
Workstation guidelines ................................................................................ 23

5 Removal and replacement procedures for Authorized Service Provider parts ................................................... 25
Component replacement procedures .................................................................................................................. 25
Bottom cover ..................................................................................................................................... 25

v
 Battery ............................................................................................................................................... 27
WLAN module .................................................................................................................................... 28
Solid-state drive ................................................................................................................................ 30
Fans ................................................................................................................................................... 31
Heat sink ............................................................................................................................................ 32
USB board .......................................................................................................................................... 34
Fingerprint reader assembly ............................................................................................................. 35
Power connector cable ...................................................................................................................... 36
TouchPad ........................................................................................................................................... 38
Speakers ............................................................................................................................................ 41
System board .................................................................................................................................... 43
Display assembly ............................................................................................................................... 45
Top cover with keyboard ................................................................................................................... 54

6 Using Setup Utility (BIOS) ............................................................................................................................. 57

Starting Setup Utility (BIOS) ................................................................................................................................ 57
Updating Setup Utility (BIOS) .............................................................................................................................. 57
Determining the BIOS version ........................................................................................................... 57
Downloading a BIOS update .............................................................................................................. 58

7 Backing up, restoring, and recovering ........................................................................................................... 59

Backing up information and creating recovery media ........................................................................................ 59
Using Windows tools ......................................................................................................................... 59
Using the HP Cloud Recovery Download Tool to create recovery media (select products only) ..... 59
Restoring and recovery ........................................................................................................................................ 60
Restoring, resetting, and refreshing using Windows tools .............................................................. 60
Recovering using HP Recovery media ............................................................................................... 60
Changing the computer boot order ................................................................................................... 60

8 Using HP PC Hardware Diagnostics ................................................................................................................ 61

Using HP PC Hardware Diagnostics Windows (select products only) ................................................................. 61
Downloading HP PC Hardware Diagnostics Windows ....................................................................... 61
Downloading the latest HP PC Hardware Diagnostics Windows version ....................... 62
Downloading HP Hardware Diagnostics Windows by product name or number
(select products only) ..................................................................................................... 62
Installing HP PC Hardware Diagnostics Windows ............................................................................. 62
Using HP PC Hardware Diagnostics UEFI ............................................................................................................. 62
Starting HP PC Hardware Diagnostics UEFI ....................................................................................... 63
Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive .............................................. 63
Downloading the latest HP PC Hardware Diagnostics UEFI version .............................. 63

vi
 Downloading HP PC Hardware Diagnostics UEFI by product name or number
(select products only) ..................................................................................................... 63
Using Remote HP PC Hardware Diagnostics UEFI settings (select products only) ............................................. 64
Downloading Remote HP PC Hardware Diagnostics UEFI ................................................................. 64
Downloading the latest Remote HP PC Hardware Diagnostics UEFI version ................. 64
Downloading Remote HP PC Hardware Diagnostics UEFI by product name or
number ............................................................................................................................ 64
Customizing Remote HP PC Hardware Diagnostics UEFI settings .................................................... 64

9 Specifications .............................................................................................................................................. 67
Computer specifications ...................................................................................................................................... 67
33.8-cm (13.3-in) display specifications ............................................................................................................. 68
M.2 solid-state drive specifications .................................................................................................................... 69

10 Power cord set requirements ...................................................................................................................... 71

Requirements for all countries ............................................................................................................................ 71
Requirements for specific countries and regions ................................................................................................ 72

11 Recycling .................................................................................................................................................. 75

Index ............................................................................................................................................................. 77

vii
viii
1 Product description

Category Description

Product Name HP Pavilion 13 Laptop PC

* Model numbers: 13-an0xxx

* CTO model number: 13t-an000

Processors 8th generation Intel® Core™ processors:

i7-8565U 1.80-GHz (SC turbo up to 4.60-GHz) quad-core processor (8.0-MB L3 cache, 2400-MHz FSB, 15 W)

i5-8265U 1.60-GHz (SC turbo up to 3.90-GHz) quad-core processor (6.0-MB L3 cache, 2400-MHz FSB, 15 W)

i3-8145U 2.10-GHz (SC turbo up to 3.90-GHz) quad-core processor (4.0-MB L3 cache, 2400-MHz FSB, 15 W)

Graphics Intel UHD Graphics 620

Panel 13.3-in, white light-emitting (WLED), BrightView, eDP, 16:9 ultra wide aspect ratio:

High-definition (HD) (1366×768), SVA, 45% CG, eDP, slim-flat (3.0 mm), 220 nits

Full high-definition (FHD) (1920×1080), UWVA, 45% CG, eDP, slim-flat (3.0 mm), 220 nits

Full high-definition (FHD) (1920×1080), UWVA, 72% CG, eDP 1.3+PSR, uslim-flat (2.0 mm), 300 nits

Memory On-board system memory, non-customer-accessible/non-upgradable

Supports up to 8-GB of system memory

DDR4-2400 single channel support (available only for 8 GB)

DDR4-2400 single channel support (DDR4-2666 bridged to DDR4-2400) (available only for 8 GB)

DDR4-2400 single channel support (DDR4-2666 downgraded to DDR4-2400) (available only for 4 GB)

Supports the following configurations:

● 8192 GB

● 4096 GB

Storage M.2, PCIe, NVMe, TLC, solid-state drive:

256-GB

M.2, PCIe, NVMe, value, solid-state drive:

512-GB

256-GB

M.2 SATA-3, solid-state drive, TLC:

256-GB

128-GB

Camera HP Wide Vision HD camera with indicator light, USB 2.0, HD BSI sensor, f2.0, WDR, 88° wide field of vision

720p by 30 frames per second

1
 Category Description

Dual array digital microphones with appropriate software - beam forming, echo cancellation, noise
suppression

Audio B&O Play Audio

Audio codec: ALC3258-CG

Supports HP Audio Boost

Dual speakers

Wireless Turbo Lite WLAN SVTP

Integrated wireless options with dual antennas:

Realtek RTL8822BE 802.11 ac 2×2 WiFi + Bluetooth 4.2 Combo Adapter (MU-MIMO supported)

Intel Wireless-AC 9560 802.11ac 2×2 WiFi + Bluetooth5 (non-vPro) (MU-MIMO, Gigabit WiFi speeds supported)

Integrated wireless options with single antenna:

Intel Wireless-AC 9461 802.11ac 1×1 WiFi + Bluetooth5 (non-vPro) (MU-MIMO supported)

External media cards HP Multi-Format Digital Media Card Reader

Supports SD/SDHC/SDXC

Push-push insertion/removal

SIM slot (toolless, user accessible)

Internal card One M.2 slot for solid-state drive

expansion
One M.2 slot for WLAN

Ports Hot plug/unplug and auto detect for correct output to wide-aspect vs. standard aspect video (auto adjust
panel resolution to fit embedded panel and external monitor connected)

HDMI v1.4 supporting up to 1920×1080 @ 60Hz

AC Smart Pin adapter plug

Audio-out (headphone)/audio-in (microphone) combo jack

USB 3.1 Gen 1 Type-A ports (2, left side)

USB 3.1 Gen 1 Type-C port (right side)

Keyboard/TouchPad Keyboard:

Full-sized, 2-coat paint, island-style keyboard

Full-sized, 3-coat paint, backlit, island-style keyboard

Full-sized, 4-coat paint, backlit, island-style keyboard

TouchPad requirements:

Image sensor

Multitouch gestures enabled

Support for Modern TrackPad gestures

Taps enabled as default

Power requirements Battery:

2 Chapter 1 Product description

Category Description

2-cell, 37.7-WHr, long-life battery

Supports battery life enhancement

AC adapter, barrel type, nPFC:

65-W, EM

45-W, right angle

45-W, for use in Argentina

Power cord:

1.0 m conventional power cord with a C5 connector

1.0 m conventional power cord with a C5 connector + Japan plug adapter

Security Kensington Nano Security Slot

Fingerprint reader (select models only)

Operating system FreeDOS 2.0

Windows 10 Home 64

Windows 10 Home 64 Chinese Market CPPP

Windows 10 Home 64 High-End Chinese Market CPPP

Windows 10 Home 64 Plus

Windows 10 Home 64 Plus Single Language

Windows 10 Home 64 Plus Single Language APAC EM PPP

Windows 10 Home 64 Plus Single Language India Market PPP

Windows 10 Home 64 Plus Single Language Indonesia Market PPP

Windows 10 Home 64 Single Language

Windows 10 Home 64 Single Language APAC EM PPP

Windows 10 Home 64 Single Language India Market PPP

Windows 10 Home 64 Single Language Indonesia Market PPP

Windows 10 Pro 64

Windows 10 Pro 64 Chinese Market

Windows 10 Pro S 64

Serviceability End user replaceable parts:

AC adapter

3
4 Chapter 1 Product description
2 Getting to know your computer

Your computer features top-rated components. This chapter provides details about your components, where
they're located, and how they work.

Right side

Component Description

(1) Memory card reader Reads optional memory cards that enable you to store, manage,
share, or access information.

To insert a card:

1. Hold the card label-side up, with connectors facing the

computer.

2. Insert the card into the memory card reader, and then
press in on the card until it is firmly seated.

To remove a card:

▲ Press in on the card, and then remove it from the memory

card reader.

(2) Audio-out (headphone)/Audio-in (microphone) Connects optional powered stereo speakers, headphones,
combo jack earbuds, a headset, or a television audio cable. Also connects an
optional headset microphone. This jack does not support
optional standalone microphones.

WARNING! To reduce the risk of personal injury, adjust the

volume before putting on headphones, earbuds, or a headset.
For additional safety information, refer to the Regulatory,
Safety, and Environmental Notices.

To access this guide:

▲ Select the Start button, select HP Help and Support, and

then select HP Documentation.

NOTE: When a device is connected to the jack, the computer

speakers are disabled.

(3) Fingerprint reader (select products only) Allows a fingerprint logon to Windows, instead of a password
logon.

▲ To use the fingerprint reader, place your finger on the

fingerprint reader for a few seconds until it reads your
fingerprint.

Right side 5
 Component Description

(4) USB Type-C port Connects a USB device, such as a cell phone, camera, activity
tracker, or smartwatch, and provides data transfer.

NOTE: Cables and/or adapters (purchased separately) may be

required.

(5) HDMI port Connects an optional video or audio device, such as a high-
definition television, any compatible digital or audio component,
or a high-speed High-Definition Multimedia Interface (HDMI)
device.

(6) AC adapter and battery light ● White: The AC adapter is connected and the battery is fully
charged.

● Blinking white: The AC adapter is disconnected and the

battery has reached a low battery level.

● Amber: The AC adapter is connected and the battery is

charging.

● Off: The battery is not charging.

(7) Power connector Connects an AC adapter.

Left side

Component Description

(1) USB ports (2) Connect a USB device, such as a cell phone, camera, activity
tracker, or smartwatch, and provide data transfer.

(2) Kensington Nano Security slot Attaches an optional security cable to the computer.

NOTE: The security cable is designed to act as a deterrent, but

it may not prevent the computer from being mishandled or
stolen.

6 Chapter 2 Getting to know your computer

Display

Component Description

(1) WLAN antennas* Send and receive wireless signals to communicate with wireless local
area networks (WLANs).

(2) Internal microphones Record sound.

(3) Camera light On: The camera is in use.

(4) Camera Allows you to video chat, record video, and record still images. Some
cameras also allow a facial recognition logon to Windows, instead of
a password logon.

NOTE: Camera functions vary depending on the camera hardware

and software installed on your product.

*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the
antennas free from obstructions.

For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or
region.

To access this guide:

▲ Select the Start button, select HP Help and Support, and then select HP Documentation.

Display 7
 Keyboard area
TouchPad

Component Description

(1) TouchPad zone Reads your finger gestures to move the pointer or activate items
on the screen.

(2) Left control zone Textured area that allows you to perform additional gestures.

(3) Right control zone Textured area that allows you to perform additional gestures.

8 Chapter 2 Getting to know your computer

Lights

Component Description

(1) Power light ● On: The computer is on.

● Blinking: The computer is in the Sleep state, a power-

saving state. The computer shuts off power to the display
and other unneeded components.

● Off: The computer is off or in Hibernation. Hibernation is a

power-saving state that uses the least amount of power.

(2) Caps lock light On: Caps lock is on, which switches the key input to all capital
letters.

(3) Mute light ● On: Computer sound is off.

● Off: Computer sound is on.

Keyboard area 9
 Button and speakers

Component Description

(1) Power button ● When the computer is off, press the button to turn on the
computer.

● When the computer is on, press the button briefly to

initiate Sleep.

● When the computer is in the Sleep state, press the button

briefly to exit Sleep (select products only).

● When the computer is in Hibernation, press the button

briefly to exit Hibernation.

CAUTION: Pressing and holding down the power button results

in the loss of unsaved information.

If the computer has stopped responding and shutdown

procedures are ineffective, press and hold the power button
down for at least 5 seconds to turn off the computer.

To learn more about your power settings, see your power

options:

▲
Right-click the Power icon , and then select Power

Options.

(2) Speakers (2) Produce sound.

10 Chapter 2 Getting to know your computer

Special keys

Component Description

(1) esc key Displays system information when pressed in combination with
the fn key.

(2) fn key Executes specific functions when pressed in combination with

another key.

(3) Windows key Opens the Start menu.

NOTE: Pressing the Windows key again will close the Start
menu.

(4) Action keys Execute frequently used system functions.

NOTE: On select products, the f5 action key turns the keyboard

backlight feature off or on.

Keyboard area 11
 Action keys
An action key performs the function indicated by the icon on the key. To determine which keys are on your
product, see Special keys on page 11.
▲ To use an action key, press and hold the key.

Icon Description

Opens the “How to get help in Windows 10” webpage.

Decreases the screen brightness incrementally as long as you hold down the key.

Increases the screen brightness incrementally as long as you hold down the key.

Switches the screen image between display devices connected to the system. For example, if a monitor is
connected to the computer, repeatedly pressing this key alternates the screen image from the computer
display to the monitor display to a simultaneous display on both the computer and the monitor.

Turns the keyboard backlight off or on. On select products, you can adjust the brightness of the keyboard
backlight. Press the key repeatedly to adjust the brightness from high (when you first start up the computer),
to low, to off. After you adjust the keyboard backlight setting, the backlight will revert to your previous
setting each time you turn on the computer. The keyboard backlight will turn off after 30 seconds of
inactivity. To turn the keyboard backlight back on, press any key or tap the TouchPad (select products only).
To conserve battery power, turn off this feature.

Mutes or restores speaker sound.

Decreases speaker volume incrementally while you hold down the key.

Increases speaker volume incrementally while you hold down the key.

Plays the previous track of an audio CD or the previous section of a DVD or a Blu-ray Disc (BD).

Starts, pauses, or resumes playback of an audio CD, a DVD, or a BD.

Plays the next track of an audio CD or the next section of a DVD or a BD.

Turns the airplane mode and wireless feature on or off.

NOTE: The airplane mode key is also referred to as the wireless button.

NOTE: A wireless network must be set up before a wireless connection is possible.

12 Chapter 2 Getting to know your computer

Bottom

Component Description

Vent Enables airflow to cool internal components.

NOTE: The computer fan starts up automatically to cool internal

components and prevent overheating. It is normal for the internal
fan to cycle on and off during routine operation.

Bottom 13
 Labels
The labels affixed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer. Labels may be in paper form or imprinted on the
product.

IMPORTANT: Check the following locations for the labels described in this section: the bottom of the
computer, inside the battery bay, under the service door, on the back of the display, or on the bottom of a
tablet kickstand.

● Service label—Provides important information to identify your computer. When contacting support, you
may be asked for the serial number, the product number, or the model number. Locate this information
before you contact support.

Component

(1) HP product name

(2) Model number

(3) Product ID

(4) Serial number

(5) Warranty period

● Regulatory label(s)—Provide(s) regulatory information about the computer.

● Wireless certification label(s)—Provide(s) information about optional wireless devices and the approval
markings for the countries or regions in which the devices have been approved for use.

14 Chapter 2 Getting to know your computer

3 Illustrated parts catalog

NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.

Computer components

Computer components 15
 Item Component Spare part number

(1) Display assembly: The display assembly is spared at the subcomponent level only. For more display assembly spare part
information, see Display assembly components on page 18.

(2) Top cover with keyboard

Non-backlit keyboard, includes fingerprint reader, pike silver L37530-xx1

Backlit keyboard, includes fingerprint reader, pike silver L37531-xx1

Non-backlit keyboard, no fingerprint reader, pike silver L37533-xx1

Backlit keyboard, no fingerprint reader, pike silver L37534-xx1

Backlit keyboard, includes fingerprint reader, mineral silver (-001 United States only) L37532-xx1

(3) TouchPad

NOTE: The TouchPad cable is available using spare part number L37375-001.

Pike silver L38040-001

Mineral silver L38043-001

(4) TouchPad bracket included in TouchPad spare

kit

(5) Fingerprint reader (includes bracket)

Pike silver models L37373-001

Mineral silver models L38041-001

(6) Power connector cable L37358-001

NOTE: The power connector cable Mylar light cover is available using spare part number
L45223-001.

(7) Speaker Kit (includes cable) L37374-001

(8) USB board L37372-001

NOTE: The USB board cable is available using spare part number L37371-001.

(9) System board (includes processor and replacement thermal material):

Intel Core i7-8565U processor, 8 GB of system memory, fingerprint reader L37351-xx1

Intel Core i5-8265U processor, 8 GB of system memory, fingerprint reader L37350-xx1

Intel Core i5-8265U processor, 8 GB of system memory, no fingerprint reader L37349-xx1

Intel Core i5-8265U processor, 4 GB of system memory, fingerprint reader L37348-xx1

Intel Core i3-8145U processor, 8 GB of system memory, fingerprint reader L42277-xx1

Intel Core i3-8145U processor, 4 GB of system memory, fingerprint reader L37347-xx1

(10) Heat sink (includes replacement thermal material): L37377-001

(11) Fan (includes cable) L37376-001

(12) WLAN module:

Realtek RTL8822BE 802.11ac 2×2 WiFi + Bluetooth 4.2 (MU-MIMO supported) 924813-855

Intel Wireless-AC 9560 802.11ac 2×2 WiFi + Bluetooth5 (non-vPro) (MU-MIMO, Gigabit WiFi L22634-005
speeds supported)

16 Chapter 3 Illustrated parts catalog

 Item Component Spare part number

Intel Wireless-AC 9461 802.11ac 1×1 WiFi + Bluetooth5 (non-vPro) (MU-MIMO supported) L25889-005

(13) Solid-state drive (2280 M.2):

512-GB, PCIe, NVMe L37357-001

256-GB, PCIe, NVMe, TLC L38076-001

256-GB, PCIe, NVMe L37356-001

256-GB, SATA-3, TLC L38042-001

128-GB, SATA-3, TLC L37355-001

(14) Battery (2-cell, 37-WHr, 4.96-AHr, Li-ion) L28076-005

(15) Bottom cover

Pike silver L37379-001

Mineral silver L37378-001

(16) Rubber Foot Kit

Pike silver L37381-001

Mineral silver L37380-001

Cables

Item Component Spare part number

(1) Display/camera cable L37361-001

(2) USB board cable L37371-001

(3) TouchPad cable L37375-001

Cables 17
 Display assembly components

Item Component Spare part number

(1) Display bezel:

220n L37359-001

300n L37360-001

(2) Display panel (includes bezel adhesive and display panel adhesive)

FHD, UWVA, 220 nits, slim L37352-001

FHD, UWVA, 300 nits, uslim L37353-001

HD, SVA, 220 nits L37354-001

(3) Hinges (include left and right display hinges) L37382-001

(4) Wireless antennas (includes bezel adhesive and display panel adhesive) L37539-001

(5) Display panel cable (includes the camera/microphone module cable) L37361-001

(6) Camera/microphone module (includes bezel adhesive and display panel adhesive) L37362-001

18 Chapter 3 Illustrated parts catalog

 Item Component Spare part number

(7) Hinge covers (includes bezel adhesive and display panel adhesive)

Mineral silver L37383-001

Pike silver L37384-001

(8) Display back cover (includes bezel adhesive):

Mineral silver, use with 220n bezel L37363-001

Pale gold + pike silver, use with 220n bezel L37365-001

Tranquil pink, use with 220n models L37366-001

Mineral silver, use with 300n bezel L37367-001

Pale gold + mineral silver, use with 220n bezel L37368-001

Pale gold + pike silver, use with 300n bezel L37369-001

Tranquil pink, use with 300n models L37370-001

Pale gold + mineral silver, use with 300n bezel L40834-001

Display enclosure adhesive (secures display panel to display enclosure; not illustrated) L38078-001

Display bezel adhesive (not illustrated) L38077-001

Display hinge gaskets (not illustrated) L45222-001

Mass storage devices

Component Spare part number

Solid-state drives (M.2)

512-GB, PCIe, NVMe L37357-001

256-GB, PCIe, NVMe, TLC L38076-001

256-GB, PCIe, NVMe L37356-001

256-GB, SATA-3, TLC L38042-001

128-GB, SATA-3, TLC L37355-001

External USB optical drive 747080-001

Mass storage devices 19

 Miscellaneous parts
Component Spare part number

AC adapter:

45-W AC adapter (non-PFC, 4.5-mm) 741727-001

45-W HP Smart AC adapter (non-PFC, 4.5-mm, for use in Argentina) 741553-852

65-W AC adapter (non-PFC, RC, EM, 4.5-mm) 913691-850

HP HDMI-to-VGA adapter 701943-001

USB-C to USB-A adapter 833960-001

HP USB to Gigabit RJ-45 Adapter 829941-001

HP USB-C to RJ-45 Adapter 855560-001

HP USB-C to USB-A Hub 916838-001

Power cord (C5 connector, 1.0 m):

For use in Argentina L19357-001

For use in Australia L19358-001

For use in Brazil L19359-001

For use in Denmark L19360-001

For use in Europe L19361-001

For use in India L19363-001

For use in Israel L19362-001

For use in Italy L19364-001

For use in Japan L19365-001

For use in Japan (duckhead) L33157-001

For use in North America L19367-001

For use in the People’s Republic of China L19368-001

For use in South Africa L19369-001

For use in South Korea L19366-001

For use in Switzerland L19370-001

For use in Taiwan L19372-001

For use in Thailand L19371-001

For use in the United Kingdom L19373-001

External USB optical drive (not illustrated) 747080-001

Rubber Foot Kit, pike silver L37381-001

Rubber Foot Kit, mineral silver L37380-001

Screw Kit L37385-001

20 Chapter 3 Illustrated parts catalog

4 Removal and replacement procedures
preliminary requirements

Tools required
You will need the following tools to complete the removal and replacement procedures:
● Flat-bladed screwdriver
● Magnetic screwdriver
● Phillips P0 and P1 screwdrivers

Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.

NOTE: As you remove each subassembly from the computer, place the subassembly (and all accompanying
screws) away from the work area to prevent damage.

Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care
when handling the plastic parts. Apply pressure only at the points designated in the
maintenance instructions.

Cables and connectors

CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the
reassembly process. Improper cable placement can damage the computer.

Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat
the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught
or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear
easily.

Tools required 21
 Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is
off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, place it in a static-proof bag.
Avoid exposing an internal hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”

Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine
the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many
cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal
cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life
expectancy.

CAUTION: To prevent damage to the computer when you are removing or installing internal components,
observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Before touching an electronic component, discharge static electricity by using the guidelines described in this
section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.

The following table shows how humidity affects the electrostatic voltage levels generated by
different activities.

CAUTION: A product can be degraded by as little as 700 V.

22 Chapter 4 Removal and replacement procedures preliminary requirements

 Typical electrostatic voltage levels

Relative humidity

Event 10% 40% 55%

Walking across carpet 35,000 V 15,000 V 7,500 V

Walking across vinyl floor 12,000 V 5,000 V 3,000 V

Motions of bench worker 6,000 V 800 V 400 V

Removing DIPS from plastic tube 2,000 V 700 V 400 V

Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V

Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V

Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V

Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V

Packaging and transporting guidelines

Follow these grounding guidelines when packaging and transporting equipment:
● To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
● Place items on a grounded surface before removing items from their containers.
● Always be properly grounded when touching a component or assembly.
● Store reusable ESD-sensitive parts from assemblies in protective packaging or non-conductive foam.
● Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid
static charging. When grounding is not possible, use an ionizer to dissipate electric charges.

Workstation guidelines

Follow these grounding workstation guidelines:

● Cover the workstation with approved static-shielding material.
● Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
● Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
● When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials.
● Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids
and Styrofoam.
● Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
● Avoid contact with pins, leads, or circuitry.
● Turn off power and input signals before inserting or removing connectors or test equipment.

Grounding guidelines 23
 Equipment guidelines

Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap
snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips
to connect a wrist strap.
● When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be
used at standing workstations and are compatible with most types of shoes or boots. On conductive
floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance
between the operator and ground. To be effective, the conductive must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
● Antistatic tape
● Antistatic smocks, aprons, and sleeve protectors
● Conductive bins and other assembly or soldering aids
● Nonconductive foam
● Conductive tabletop workstations with ground cords of one megohm resistance
● Static-dissipative tables or floor mats with hard ties to the ground
● Field service kits
● Static awareness labels
● Material-handling packages
● Nonconductive plastic bags, tubes, or boxes
● Metal tote boxes
● Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.

Material Use Voltage protection level

Antistatic plastics Bags 1,500 V

Carbon-loaded plastic Floor mats 7,500 V

Metallized laminate Floor mats 5,000 V

24 Chapter 4 Removal and replacement procedures preliminary requirements

5 Removal and replacement procedures for
Authorized Service Provider parts

This chapter provides removal and replacement procedures for Authorized Service Provider only parts.

CAUTION: Components described in this chapter should only be accessed by an authorized service provider.
Accessing these parts can damage the computer or void the warranty.
CAUTION: Only HP authorized service providers should perform the removal and replacement procedures
described here. Accessing the internal part could damage the computer or void the warranty.

Component replacement procedures

NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Labels on page 14 for details.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.

There are as many as 54 screws that must be removed, replaced, and/or loosened when servicing Authorized
Service Provider only parts. Make special note of each screw size and location during removal
and replacement.

Bottom cover
Description Spare part number

Bottom cover L37379-001

Before removing the bottom cover, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
Remove the bottom cover:
1. Remove the two rubber feet (1) toward the top of the computer.
The rubber feet are available using spare part number L37381-001 for pike silver models and
L37380-001 for mineral silver models.
2. Remove the two Phillips M2.5×5.0 screws (2) under the rubber feet.

Component replacement procedures 25

 3. Remove the three Phillips M2.0×2.5 screws (3) along the bottom edge on the bottom cover.

4. Starting under the hinges, use a thin, non-conductive tool to disengage the bottom cover from the
computer (1).
5. Lift up along the top (2), and left (3) and right (4) sides to remove the bottom cover.

Reverse this procedure to install the bottom cover.

26 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Battery
Description Spare part number

2-cell, 37-WHr, 4.96-AHr, Li-ion battery L28076-005

Before removing the battery, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
Remove the battery:
1. Disconnect the battery cable from the system board (1).
2. Remove the six Phillips M2.0×2.5 screws (2) that secure the battery to the computer.
3. Lift the inside of the battery, and then remove the battery from the computer (3).

TIP: When installing the battery, make sure to route the cable in the clips near the top of the battery
(4).

Reverse this procedure to install the battery.

Component replacement procedures 27

 WLAN module
Description Spare part number

Realtek RTL8822BE 802.11ac 2×2 WiFi + Bluetooth 4.2 924813-855

Intel Wireless-AC 9560 802.11ac 2×2 WiFi + Bluetooth5 (non-vPro) L22634-005

Intel Wireless-AC 9461 802.11ac 1×1 WiFi + Bluetooth5 (non-vPro) L25889-005

CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the computer by the governmental agency that regulates wireless devices in your
country or region. If you replace the module and then receive a warning message, remove the module to
restore device functionality, and then contact technical support.

Before removing the WLAN module, follow these steps:

1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the WLAN module:
1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.

NOTE: Some models have only one antenna cable.

The WLAN antenna cable labeled "1/MAIN" connects to the WLAN module "Main" terminal. The WLAN
antenna cable labeled "2/AUX" connects to the WLAN module "Aux" terminal.

2. Remove the Phillips M2.0×3.0 screw (2) that secures the WLAN module to the computer. (The WLAN
module tilts up.)

28 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
3. Remove the WLAN module (3) by pulling the module away from the slot at an angle.

NOTE: The WLAN module is designed with a notch to prevent incorrect insertion.

Reverse this procedure to install the WLAN module.

Component replacement procedures 29

 Solid-state drive
Description Spare part number

512-GB, PCIe, NVMe L37357-001

256-GB, PCIe, NVMe, TLC L38076-001

256-GB, PCIe, NVMe L37356-001

256-GB, SATA-3, TLC L38042-001

128-GB, SATA-3, TLC L37355-001

Before removing the solid-state drive, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the solid-state drive:
1. Remove the Phillips M2.0×3.0 screw (1) that secures the drive to the computer.
2. Remove the drive (2) by pulling it away from the connector.

Reverse this procedure to install the solid-state drive.

30 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Fans
Description Spare part number

Fan L37376-001

Before removing the fans, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the fans:

TIP: The computer uses two fans, both of which are the same and can be removed individually.

1. Disconnect the fan cables (1) from the system board.

2. Remove the three Phillips M2.0×2.5 screws (2) that secure each fan to the computer.
3. Remove the fans from the computer (3).

Reverse these procedures to install the fans.

Component replacement procedures 31

 Heat sink
NOTE: The heat sink spare part kit includes replacement thermal material.

Description Spare part number

Heat sink L37377-001

Before removing the heat sink, follow these steps:

1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the heat sink:
1. In the order indicated on the heat sink, remove the three Phillips M2.0×2.5 screws (1) that secure
the heat sink to the system board.
2. Remove the heat sink (2).

Each time the heat sink is removed, thoroughly clean the thermal material from the surface of the soldered
processor on the system board (1) and the associated section of the heat sink (2). Replacement thermal
material is included with the heat sink and system board spare part kits.

32 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Reverse this procedure to install the heat sink.

Component replacement procedures 33

 USB board
Description Spare part number

USB board L37372-001

USB board cable L37371-001

Before removing the USB board, follow these steps:

1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the USB board:
1. Disconnect the cable from the ZIF connector on the USB board (1).
2. Remove the four Phillips M2.0×2.5 screws (2) that secure the board to the computer.
3. Remove the board from the computer (3).

Reverse this procedure to install the USB board.

34 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Fingerprint reader assembly
Description Spare part number

Fingerprint reader assembly, pike silver (includes bracket) L37373-001

Fingerprint reader assembly, mineral silver (includes bracket) L38041-001

Before removing the fingerprint reader assembly, follow these steps:

1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the fingerprint reader assembly:
1. Disconnect the cable from the system board ZIF connector (1).
2. Lift to remove the bracket from the computer (2).
3. From the outside of the chassis, push the fingerprint reader module into the chassis (3), and then
remove the module and cable from the computer (4).

Reverse this procedure to install the fingerprint reader assembly.

Component replacement procedures 35

 Power connector cable
Description Spare part number

Power connector cable L37358-001

Power connector cable Mylar light cover L45223-001

Before removing the power connector cable, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Disconnect the battery (see Battery on page 27).
Remove the power connector cable:
1. Remove the two Phillips M2.5×6.0 screws (1) from the right display hinge, and then rotate the hinge
open as far as possible (2).

2. Remove the Phillips M2.0×2.5 screw (1) from the bracket, and then remove the bracket from on top of
the connector (2).
3. Disconnect the power connector cable from the system board (3).

36 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
4. Remove the connector cable from the computer (4).

Reverse this procedure to install the power connector cable.

When installing the power connector cable, be sure to install the Mylar light cover as shown in the following
illustration.

Component replacement procedures 37

 TouchPad
Description Spare part number

TouchPad, pike silver L38040-001

TouchPad, mineral silver L38043-001

TouchPad cable L37375-001

Before removing the TouchPad, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Remove the battery (see Battery on page 27).
Remove the TouchPad:
1. Remove the four Phillips M2.0×2.5 screws (1) that secure the TouchPad bracket to the computer.
2. Remove the bracket (2).

38 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
3. Rotate the left side of the clear plastic cover from atop the screws (1) to disengage the adhesive (2) that
secures it. Remove the plastic cover.

4. Lift the Mylar enough to access the conductive tape (1), and then remove the tape from the right side of
the TouchPad (2).

5. Disconnect the cable from the ZIF connector on the TouchPad (1).
6. Using a P0 driver, remove the three Phillips M2.0×2.0 broad head screws (2) that secure the TouchPad to
the computer.

Component replacement procedures 39

 7. From underneath the upside-down computer, press near the top of the TouchPad and push it upward to
remove it from the computer (3).

Reverse this procedure to install the TouchPad.

40 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Speakers
Description Spare part number

Speakers (includes cable) L37374-001

Before removing the speakers, follow these steps:

1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
3. Disconnect all external devices from the computer.
4. Remove the following components:
a. Bottom cover (see Bottom cover on page 25)
b. Battery (see Battery on page 27)
c. Heat sink (see Heat sink on page 32)
d. USB board (see USB board on page 34)
e. Fans (see Fans on page 31)
Remove the speakers:
1. Remove the two Phillips M2.5×6.0 screws (1) from the right display hinge, and then rotate the hinge
open as far as possible (2).
2. Disconnect the display cable from the system board (3), and then remove the cable from the retention
clips and routing channel built into the right speaker (4).

Component replacement procedures 41

 3. Disconnect the antennas from the WLAN module (5), and then remove the antenna cables from the
retention clips and routing channel built into the left speaker (6).

4. Disconnect the speaker cable from the system board (1).

5. Remove the cable between the speakers from the clips under the removed fans (2).
6. Remove the three Phillips M2.0×2.5 screws (3) from the speakers.
7. Remove the speakers from the computer (4).

Reverse this procedure to install the speakers.

42 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
System board
NOTE: All system board spare part kits include a processor and replacement thermal material.

Description Spare part number

Intel Core i7-8565U processor, 8 GB of system memory, fingerprint reader L37351-xx1

Intel Core i5-8265U processor, 8 GB of system memory, fingerprint reader L37350-xx1

Intel Core i5-8265U processor, 8 GB of system memory, no fingerprint reader L37349-xx1

Intel Core i5-8265U processor, 4 GB of system memory, fingerprint reader L37348-xx1

Intel Core i3-8145U processor, 8 GB of system memory, fingerprint reader L42277-xx1

Intel Core i3-8145U processor, 4 GB of system memory, fingerprint reader L37347-xx1

Before removing the system board, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Bottom cover (see Bottom cover on page 25)
b. Battery (see Battery on page 27)
c. Power connector cable bracket (see Power connector cable on page 36)
When replacing the system board, be sure to remove the following components from the defective system
board and install them on the replacement system board:
● WLAN module (see WLAN module on page 28)
● Solid-state drive (see Solid-state drive on page 30)
● Fans (see Fans on page 31)
● Heat sink (see Heat sink on page 32)
Remove the system board:
1. Disconnect the following cables:
(1) Fingerprint reader cable
(2) Power connector cable
(3) Display cable
(4) Speaker cable
(5) USB board cable
(6) Backlight cable
(7) Keyboard cable

Component replacement procedures 43

 (8) TouchPad cable

2. Remove the Phillips M2.0×2.5 screw (1) that secures the system board to the computer.
3. Remove the two broad head Phillips M2.0×2.0 screws (2) that secure the system board to the computer.
4. Lift the right side of the system board (3), and the pull the system board to the right and out of the
computer (4).

Reverse this procedure to install the system board.

44 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Display assembly
NOTE: The display assembly is spared at the subcomponent level. For display assembly spare part
information, see the individual removal subsections.

Before removing the display assembly, follow these steps:

1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the bottom cover (see Bottom cover on page 25).
5. Remove the battery (see Battery on page 27).
Remove the display assembly:
1. Disconnect the display cable from the system board ZIF connector (1).
2. Release the display panel from the retention clip (2) and routing channel built into the right speaker.
3. Disconnect the WLAN antenna cables (3) from the terminals on the WLAN module.

NOTE: Some models have only one antenna cable.

The WLAN antenna cable labeled "1/MAIN" connects to the WLAN module "Main" terminal. The WLAN
antenna cable labeled "2/AUX" connects to the WLAN module "Aux" terminal.

4. Release the WLAN antenna cables from the retention clips (4) and routing channel built into
the computer and the left speaker.

5. Remove the four Phillips M2.5×5.0 screws (1) that secure the display assembly to the computer.
6. Rotate the display downward to separate it from the hinges (2).

Component replacement procedures 45

 7. Separate the display from the computer (3).

8. If it is necessary to remove or replace the display bezel or any of the display assembly subcomponents:
a. Release the left and right edges of the display bezel (1) from the display assembly.
b. Release the top edge of the display bezel (2) from the display assembly.
c. Release the bottom edge of the display bezel (3) from the display assembly.
d. Remove the display bezel from the display assembly (4).
The display bezel is available using the following spare part numbers:
● L37359-001 - 220n bezel
● L37360-001 - 300n bezel
Display bezel adhesive is available using spare part number L38077-001.

46 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
TIP: If replacing the bezel, make sure to use the correct size. The size is stamped on the inside of the
bezel, as shown in the following illustration.
• ‘20’ indicates the bezel is used with a 2 mm thickness display panel
• ‘30’ indicates the bezel is used with a 3 mm thickness display panel

IMPORTANT: When replacing the bezel, use the following guidelines:

- On 3 mm thickness display panels, install 2.5 mm width adhesive on the top (1) and 5 mm adhesive on
the bottom (2) of the bezel.
- On 2 mm thickness display panels, install 2.5 mm width adhesive on the top (1) and bottom (2) of the
bezel.

Component replacement procedures 47

 9. If it is necessary to replace the camera/microphone module:
a. Disconnect the cable (1) from the camera/microphone module.
b. Detach the camera/microphone module (2) from the display enclosure. (The module is attached
with double-sided adhesive.)
The camera/microphone module is available using spare part number L37362-001.

10. If it is necessary to replace the display panel:

a. The panel is secured to the display enclosure with long strips of adhesive tape located on each side
of the panel. Use a tweezer to grasp the tape just above each hinge, and then steadily pull the tape
out from behind the panel.

NOTE: You have to pull on the tape multiple times before it is completely removed.

Display adhesive tape is available using spare part number L38078-001.

48 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
 TIP: When installing a panel into the display, use the alignment marks (1), and then press the
adhesive tape onto each side of the display enclosure (2).

b. Swing the top edge of the display panel (1) forward until the panel rests upside down next to the
display.
c. Release the adhesive support strip (2) that secures the display panel cable connector to the
display panel.

Component replacement procedures 49

 d. Disconnect the display panel cable (3) from the display panel.

e. Remove the display panel.

The display panel is available using the following spare part numbers:
● L37352-001 – FHD, UWVA, slim, 220 nits
● L37353-001 – FHD, UWVA, uslim, 300 nits
● L37354-001 – HD, SVA, 220 nits
11. If it is necessary to replace the hinge covers, use a tool (1) to lift up the side of the hinge cover to remove
it (2).
Hinge covers are available using spare part number L37383-001 for mineral silver models and
L37384-001 for pike silver models.

50 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
12. If it is necessary to replace the display hinges:
a. Remove the two Phillips M2.0×2.5 screws (1) from the top of the hinges.
b. Remove the six Phillips M2.0×2.5 broad head screws (2) from the bottom of the hinges.
c. Remove the two gaskets from the bottom of the display hinges as shown in the following
illustration. The gaskets are available using spare part number L45222-001.

d. Remove the display hinges (3).

The display hinges are available using spare part number L37382-001.

13. If it is necessary to replace the display panel cable:

Component replacement procedures 51

 a. Disconnect the cable from the camera module (1).
b. Lift to disengage the cable from the adhesive that secures it to the display enclosure (2).
c. Release the cable from the retention clips and routing channel (3) built into the bottom edge of the
display enclosure.
The display panel cable is available using spare part number L37361-001.

14. If it is necessary to replace the wireless antenna cables and transceivers:

a. Detach the wireless antenna transceivers (1) from the display enclosure. (The wireless antenna
transceivers are attached to the enclosure with double-sided adhesive.)

52 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
 b. Release the wireless antenna cables from the retention clips and routing channels built into the
sides and bottom of the display enclosure (2).
The wireless antenna cables and transceivers are available using spare part number L37539-001.

Reverse this procedure to reassemble and install the display assembly.

Component replacement procedures 53

 Top cover with keyboard
The top cover with keyboard remains after removing all other spared parts from the computer.
In this section, the first table provides the main spare part number for the keyboards. The second table
provides the country codes.

Description Spare part number

Top cover with non-backlit keyboard, includes fingerprint reader, pike silver L37530-xx1

Top cover with backlit keyboard, includes fingerprint reader, pike silver L37531-xx1

Top cover with non-backlit keyboard, no fingerprint reader, pike silver L37533-xx1

Top cover with backlit keyboard, no fingerprint reader, pike silver L37534-xx1

Top cover with backlit keyboard, includes fingerprint reader, mineral silver (-001 United States only) L37532-xx1

For use in country Spare part For use in country Spare part For use in country Spare part
or region number or region number or region number

Belgium -A41 Italy -061 South Korea -AD1

Bulgaria -261 Latin America -161 Spain -071

Czech Republic -FL1 The Netherlands -B31 Switzerland -BG1

and Slovakia

Denmark, Finland, and -DH1 Portugal -131 Taiwan -AB1

Norway

France -051 Romania -271 Thailand -281

Germany -041 Russia -251 Turkey -141

Greece -151 Saudi Arabia -171 United Kingdom -031

Hungary -211 Slovenia -BA1 United States -001

Israel -BB1

When replacing the top cover, be sure to install the Mylar shielding onto the top cover, noting the three
positioning screw holes in the Mylar.

54 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
Component replacement procedures 55
56 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts
6 Using Setup Utility (BIOS)

Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and output
devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility (BIOS)
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.

NOTE: To start Setup Utility on convertible computers, your computer must be in notebook mode and you
must use the keyboard attached to your notebook.

Starting Setup Utility (BIOS)

CAUTION: Use extreme care when making changes in Setup Utility (BIOS). Errors can prevent the computer
from operating properly.

▲ Turn on or restart the computer, quickly press esc, and then press f10.

Updating Setup Utility (BIOS)

Updated versions of Setup Utility (BIOS) may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing
and troubleshooting the file.

Determining the BIOS version

To decide whether you need to update Setup Utility (BIOS), first determine the BIOS version on your computer.
To reveal the BIOS version information (also known as ROM date and System BIOS), use one of these options.
● HP Support Assistant
1. Type support in the taskbar search box, and then select the HP Support Assistant app.

– or –
Select the question mark icon in the taskbar.
2. Select My notebook, and then select Specifications.
● Setup Utility (BIOS)
1. Start Setup Utility (BIOS) (see Starting Setup Utility (BIOS) on page 57).
2. Select Main, and then make note of the BIOS version.
3. Select Exit, select one of the options, and then follow the on-screen instructions.
To check for later BIOS versions, see Downloading a BIOS update on page 58.

Starting Setup Utility (BIOS) 57

 Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do
not download or install a BIOS update while the computer is running on battery power, docked in an optional
docking device, or connected to an optional power source. During the download and installation, follow these
instructions:
● Do not disconnect power from the computer by unplugging the power cord from the AC outlet.
● Do not shut down the computer or initiate Sleep.
● Do not insert, remove, connect, or disconnect any device, cable, or cord.
NOTE: If your computer is connected to a network, consult the network administrator before installing any
software updates, especially system BIOS updates.

1. Type support in the taskbar search box, and then select the HP Support Assistant app.

– or –
Select the question mark icon in the taskbar.
2. Select Updates, and then select Check for updates and messages.
3. Follow the on-screen instructions.
4. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on your
computer. If the update is more recent than your BIOS version, make a note of the date, name, or
other identifier. You may need this information to locate the update later, after it has been
downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update is downloaded.
You will need to access this path when you are ready to install the update.
BIOS installation procedures vary. Follow any instructions that appear on the screen after the download is
complete. If no instructions appear, follow these steps:
1. Type file in the taskbar search box, and then select File Explorer.

2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder that contains the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.

NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.

58 Chapter 6 Using Setup Utility (BIOS)

7 Backing up, restoring, and recovering

This chapter provides information about the following processes, which are standard procedure for most
products:
● Backing up your personal information—You can use Windows tools to back up your personal
information (see Using Windows tools on page 59).
● Creating a restore point—You can use Windows tools to create a restore point (see Using Windows
tools on page 59).
● Creating recovery media (select products only)—You can use the HP Cloud Recovery Download Tool
(select products only) to create recovery media (see Using the HP Cloud Recovery Download Tool to
create recovery media (select products only) on page 59).
● Restoring and recovery—Windows offers several options for restoring from backup, refreshing the
computer, and resetting the computer to its original state (see Using Windows tools on page 59).

IMPORTANT: If you will be performing recovery procedures on a tablet, the tablet battery must be at least
70% charged before you start the recovery process.
IMPORTANT: For a tablet with a detachable keyboard, connect the tablet to the keyboard base before
beginning any recovery process.

Backing up information and creating recovery media

Using Windows tools
IMPORTANT: Windows is the only option that allows you to back up your personal information. Schedule
regular backups to avoid information loss.

You can use Windows tools to back up personal information and create system restore points and recovery
media.

NOTE: If computer storage is 32 GB or less, Microsoft System Restore is disabled by default.

For more information and steps, see the Get Help app.
1. Select the Start button, and then select the Get Help app.
2. Enter the task you want to perform.

NOTE: You must be connected to the Internet to access the Get Help app.

Using the HP Cloud Recovery Download Tool to create recovery media (select
products only)
You can use the HP Cloud Recovery Download Tool to create HP Recovery media on a bootable USB flash drive,
as follows:
1. Go to http://www.hp.com/support.
2. Select Software and Drivers, and then follow the on-screen instructions.

Backing up information and creating recovery media 59

 NOTE: If you cannot create recovery media yourself, contact support to obtain recovery discs. Go to
http://www.hp.com/support, select your country or region, and then follow the on-screen instructions.

Restoring and recovery

Restoring, resetting, and refreshing using Windows tools
Windows offers several options for restoring, resetting, and refreshing the computer. For details, see Using
Windows tools on page 59.

Recovering using HP Recovery media

HP Recovery media is used to recover the original operating system and software programs that were
installed at the factory. On select products, it can be created on a bootable USB flash drive using the HP Cloud
Recovery Download Tool. For details, see Using the HP Cloud Recovery Download Tool to create recovery
media (select products only) on page 59.

NOTE: If you cannot create recovery media yourself, contact support to obtain recovery discs. Go to
http://www.hp.com/support, select your country or region, and then follow the on-screen instructions.

To recover your system:

▲ Insert the HP Recovery media, and then restart the computer.

Changing the computer boot order

If your computer does not restart using the HP Recovery media, you can change the computer boot order. This
is the order of devices listed in BIOS where the computer looks for startup information. You can change the
selection to an optical drive or a USB flash drive, depending on the location of your HP Recovery media.
To change the boot order:

IMPORTANT: For a tablet with a detachable keyboard, connect the tablet to the keyboard base before
beginning these steps.

1. Insert the HP Recovery media.

2. Access the system Startup menu.
For computers or tablets with keyboards attached:
▲ Turn on or restart the computer or tablet, quickly press esc, and then press f9 for boot options.
For tablets without keyboards:
▲ Turn on or restart the tablet, quickly hold down the volume up button, and then select f9.
‒ or –
Turn on or restart the tablet, quickly hold down the volume down button, and then select f9.
3. Select the optical drive or USB flash drive from which you want to boot, and then follow the on-screen
instructions.

60 Chapter 7 Backing up, restoring, and recovering

8 Using HP PC Hardware Diagnostics

Using HP PC Hardware Diagnostics Windows (select products

only)
HP PC Hardware Diagnostics Windows is a Windows-based utility that allows you to run diagnostic tests to
determine whether the computer hardware is functioning properly. The tool runs within the Windows
operating system in order to diagnose hardware failures.
If HP PC Hardware Diagnostics Windows is not installed on your computer, first you must download and install
it. To download HP PC Hardware Diagnostics Windows, see Downloading HP PC Hardware Diagnostics
Windows on page 61.
After HP PC Hardware Diagnostics Windows is installed, follow these steps to access it from HP Help and
Support or HP Support Assistant.
1. To access HP PC Hardware Diagnostics Windows from HP Help and Support:
a. Select the Start button, and then select HP Help and Support.
b. Right-click HP PC Hardware Diagnostics Windows, select More, and then select Run as
administrator.
– or –
To access HP PC Hardware Diagnostics Windows from HP Support Assistant:
a. Type support in the taskbar search box, and then select the HP Support Assistant app.

– or –
Select the question mark icon in the taskbar.
b. Select Troubleshooting and fixes.
c. Select Diagnostics, and then select HP PC Hardware Diagnostics Windows.
2. When the tool opens, select the type of diagnostic test you want to run, and then follow the on-screen
instructions.

NOTE: If you need to stop a diagnostic test at any time, select Cancel.

3. When HP PC Hardware Diagnostics Windows detects a failure that requires hardware replacement, a 24-
digit Failure ID code is generated. For assistance in correcting the problem, contact support, and then
provide the Failure ID code.

Downloading HP PC Hardware Diagnostics Windows

● The HP PC Hardware Diagnostics Windows download instructions are provided in English only.
● You must use a Windows computer to download this tool because only .exe files are provided.

Using HP PC Hardware Diagnostics Windows (select products only) 61

 Downloading the latest HP PC Hardware Diagnostics Windows version
To download HP PC Hardware Diagnostics Windows, follow these steps:
1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed.
2. In the HP PC Hardware Diagnostics section, select Download, and then select a location on your
computer or a USB flash drive.
The tool is downloaded to the selected location.

Downloading HP Hardware Diagnostics Windows by product name or number (select products

only)
NOTE: For some products, it may be necessary to download the software to a USB flash drive by using the
product name or number.

To download HP PC Hardware Diagnostics Windows by product name or number, follow these steps:
1. Go to http://www.hp.com/support.
2. Select Get software and drivers, select your type of product, and then enter the product name or
number in the search box that is displayed.
3. In the HP PC Hardware Diagnostics section, select Download, and then select a location on your
computer or a USB flash drive.
The tool is downloaded to the selected location.

Installing HP PC Hardware Diagnostics Windows

To install HP PC Hardware Diagnostics Windows, follow these steps:
▲ Navigate to the folder on your computer or the USB flash drive where the .exe file was downloaded,
double-click the .exe file, and then follow the on-screen instructions.

Using HP PC Hardware Diagnostics UEFI

NOTE: For Windows 10 S computers, you must use a Windows computer and a USB flash drive to download
and create the HP UEFI support environment because only .exe files are provided. For more information, see
Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive on page 63.

HP PC Hardware Diagnostics UEFI (Unified Extensible Firmware Interface) allows you to run diagnostic tests to
determine whether the computer hardware is functioning properly. The tool runs outside the operating
system so that it can isolate hardware failures from issues that are caused by the operating system or other
software components.
If your PC will not boot into Windows, you can use HP PC Hardware Diagnostics UEFI to diagnose hardware
issues.
When HP PC Hardware Diagnostics UEFI detects a failure that requires hardware replacement, a 24-digit
Failure ID code is generated. For assistance in correcting the problem, contact support, and provide the Failure
ID code.

NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode, and you
must use the attached keyboard.
NOTE: If you need to stop a diagnostic test, press esc.

62 Chapter 8 Using HP PC Hardware Diagnostics

Starting HP PC Hardware Diagnostics UEFI
To start HP PC Hardware Diagnostics UEFI, follow these steps:
1. Turn on or restart the computer, and quickly press esc.
2. Press f2.
The BIOS searches three places for the diagnostic tools, in the following order:
a. Connected USB flash drive

NOTE: To download the HP PC Hardware Diagnostics UEFI tool to a USB flash drive, see
Downloading the latest HP PC Hardware Diagnostics UEFI version on page 63.

b. Hard drive
c. BIOS
3. When the diagnostic tool opens, select a language, select the type of diagnostic test you want to run,
and then follow the on-screen instructions.

Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive

Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive can be useful in the following situations:
● HP PC Hardware Diagnostics UEFI is not included in the preinstall image.
● HP PC Hardware Diagnostics UEFI is not included in the HP Tool partition.
● The hard drive is damaged.

NOTE: The HP PC Hardware Diagnostics UEFI download instructions are provided in English only, and you
must use a Windows computer to download and create the HP UEFI support environment because only .exe
files are provided.

Downloading the latest HP PC Hardware Diagnostics UEFI version

To download the latest HP PC Hardware Diagnostics UEFI version to a USB flash drive:
1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed.
2. In the HP PC Hardware Diagnostics UEFI section, select Download UEFI Diagnostics, and then select
Run.

Downloading HP PC Hardware Diagnostics UEFI by product name or number (select products

only)
NOTE: For some products, it may be necessary to download the software to a USB flash drive by using the
product name or number.

To download HP PC Hardware Diagnostics UEFI by product name or number (select products only) to a USB
flash drive:
1. Go to http://www.hp.com/support.
2. Enter the product name or number, select your computer, and then select your operating system.
3. In the Diagnostics section, follow the on-screen instructions to select and download the specific UEFI
Diagnostics version for your computer.

Using HP PC Hardware Diagnostics UEFI 63

 Using Remote HP PC Hardware Diagnostics UEFI settings (select
products only)
Remote HP PC Hardware Diagnostics UEFI is a firmware (BIOS) feature that downloads HP PC Hardware
Diagnostics UEFI to your computer. It can then execute the diagnostics on your computer, and it may upload
results to a preconfigured server. For more information on Remote HP PC Hardware Diagnostics UEFI, go to
http://www.hp.com/go/techcenter/pcdiags, and then select Find out more.

Downloading Remote HP PC Hardware Diagnostics UEFI

NOTE: HP Remote PC Hardware Diagnostics UEFI is also available as a Softpaq that can be downloaded to a
server.

Downloading the latest Remote HP PC Hardware Diagnostics UEFI version

To download the latest Remote HP PC Hardware Diagnostics UEFI version, follow these steps:
1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed.
2. In the HP PC Hardware Diagnostics UEFI section, select Download Remote Diagnostics, and then select
Run.

Downloading Remote HP PC Hardware Diagnostics UEFI by product name or number

NOTE: For some products, it may be necessary to download the software by using the product name or
number.

To download HP Remote PC Hardware Diagnostics UEFI by product name or number, follow these steps:
1. Go to http://www.hp.com/support.
2. Select Get software and drivers, select your type of product, enter the product name or number in the
search box that is displayed, select your computer, and then select your operating system.
3. In the Diagnostics section, follow the on-screen instructions to select and download the Remote UEFI
version for the product.

Customizing Remote HP PC Hardware Diagnostics UEFI settings

Using the Remote HP PC Hardware Diagnostics setting in Computer Setup (BIOS), you can perform the
following customizations:
● Set a schedule for running diagnostics unattended. You can also start diagnostics immediately in
interactive mode by selecting Execute Remote HP PC Hardware Diagnostics.
● Set the location for downloading the diagnostic tools. This feature provides access to the tools from the
HP website or from a server that has been preconfigured for use. Your computer does not require the
traditional local storage (such as a disk drive or USB flash drive) to run remote diagnostics.
● Set a location for storing the test results. You can also set the user name and password settings used for
uploads.
● Display status information about the diagnostics run previously.
To customize Remote HP PC Hardware Diagnostics UEFI settings, follow these steps:
1. Turn on or restart the computer, and when the HP logo appears, press f10 to enter Computer Setup.
2. Select Advanced, and then select Settings.

64 Chapter 8 Using HP PC Hardware Diagnostics

3. Make your customization selections.
4. Select Main, and then Save Changes and Exit to save your settings.
Your changes take effect when the computer restarts.

Using Remote HP PC Hardware Diagnostics UEFI settings (select products only) 65

66 Chapter 8 Using HP PC Hardware Diagnostics
9 Specifications

Computer specifications
Metric U.S.

Dimensions

Depth 211 mm 8.31 in

Width 311 mm 12.24 in

Height 15.4 mm 0.61 in

Weight 1308 g 2.88 lb

Input power

Operating voltage and current 19.5 V dc @ 3.33 A – 65 W

19.5 V dc @ 2.31 A – 45 W

Temperature

Operating 5°C to 35°C 41°F to 95°F

Nonoperating ‑20°C to 60°C ‑4°F to 140°F

Relative humidity (noncondensing)

Operating 10% to 90%

Nonoperating 5% to 95%

Maximum altitude (unpressurized)

Operating ‑15 m to 3,048 m ‑50 ft to 10,000 ft

Nonoperating ‑15 m to 12,192 m ‑50 ft to 40,000 ft

NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The device operates well within this range of
temperatures.

Computer specifications 67
 33.8-cm (13.3-in) display specifications
Metric U.S.

Active diagonal size 33.8-cm 13.3-in

Resolution 1366×768 (HD)

1920×1080 (FHD)

Surface treatment BrightView

Brightness 220 nits

300 nits

Backlight WLED

Graphics adapter eDP

Thickness 3.0 mm

2.0 mm

68 Chapter 9 Specifications
M.2 solid-state drive specifications
128-GB* 256-GB* 512-GB*

Dimensions

Height 1 mm 1 mm 1 mm

Length 50.8 mm 50.8 mm 50.8 mm

Width 28.9 mm 28.9 mm 28.9 mm

Weight < 10 g < 10 g < 10 g

Interface type SATA-3 (6 Gbps) SATA-3 (6 Gbps) SATA-3 (6 Gbps)

Transfer rate

Sequential Read Up to 520 MB/s Up to 540 MB/s Up to 530 MB/s

Random Read Up to 60K IOPs Up to 85K IOPs Up to 97K IOPs

Sequential Write Up to 160 MB/s Up to 280 MB/s Up to 515 MB/s

Random Write Up to 34K IOPs Up to 67K IOPs Up to 88K IOPs

Ready time, Maximum (to not 1.0 s 1.0 s 1.0 s

busy)

Access times

Logical 0.1 ms 0.1 0.1

Total logical sectors 250,069,680 500,118,192 1,000,215,216

Operating temperature

Operating 0° to 70°C (32°F to 158°F) 0° to 70°C (32°F to 158°F) 0° to 70°C (32°F to 158°F)

Non-operating -40° to 95°C (-40°F to 203°F) -55° to 90°C (-67°F to 194°F) -40° to 85°C (-40°F to 185°F)

*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.

NOTE: Certain restrictions and exclusions apply. Contact technical support for details.

M.2 solid-state drive specifications 69

70 Chapter 9 Specifications
10 Power cord set requirements

The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts ac, or from 220 to 240 volts ac.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or
region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region
where the computer is used.

Requirements for all countries

The following requirements are applicable to all countries and regions:
● The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
● All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in
the country or region where the power cord set will be used.
● The power cord sets must have a minimum current capacity of 10 A and a nominal voltage rating of 125
or 250 V ac, as required by the power system of each country or region.
● The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet
C13 connector for mating with the appliance inlet on the back of the computer.

Requirements for all countries 71

 Requirements for specific countries and regions
Country/region Accredited agency Applicable note number

Argentina IRAM 1

Australia SAA 1

Austria OVE 1

Belgium CEBEC 1

Brazil ABNT 1

Canada CSA 2

Chile IMQ 1

Denmark DEMKO 1

Finland FIMKO 1

France UTE 1

Germany VDE 1

India ISI 1

Israel SII 1

Italy IMQ 1

Japan JIS 3

The Netherlands KEMA 1

New Zealand SANZ 1

Norway NEMKO 1

The People's Republic of China CCC 4

Saudi Arabia SASO 7

Singapore PSB 1

South Africa SABS 1

South Korea KTL 5

Sweden SEMKO 1

Switzerland SEV 1

Taiwan BSMI 6

Thailand TISI 1

The United Kingdom ASTA 1

The United States UL 2

1. The flexible cord must be Type HO5VV-F, 3-conductor, 0.75mm2 conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

2. The flexible cord must be Type SVT/SJT or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V ac) or NEMA 6-15P (15 A, 250 V ac) configuration. CSA or C-UL mark. UL file number must be on
each element.

72 Chapter 10 Power cord set requirements

Country/region Accredited agency Applicable note number

3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The flexible cord must be Type VCTF, 3-conductor, 0.75mm2 or 1.25mm2 conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V ac) configuration.

4. The flexible cord must be Type RVV, 3-conductor, 0.75mm2 conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the CCC certification mark.

5. The flexible cord must be Type H05VV-F 3X0.75mm2 conductor size. KTL logo and individual approval number must be on each
element. Corset approval number and logo must be printed on a flag label.

6. The flexible cord must be Type HVCTF 3X1.25mm2 conductor size. Power cord set fittings (appliance coupler, cable, and wall plug)
must bear the BSMI certification mark.

7. For 127 V ac, the flexible cord must be Type SVT or SJT 3 x 18 AWG, with plug NEMA 5-15P (15 A, 125 V ac), with UL and CSA or C-
UL marks. For 240 V ac, the flexible cord must be Type H05VV-F 3X0.75/1.00mm2 conductor size, with plug BS 1363/A with BSI or
ASTA marks.

Requirements for specific countries and regions 73

74 Chapter 10 Power cord set requirements
11 Recycling

When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the
battery in general household waste. Follow the local laws and regulations in your area for battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable
batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle.

75
76 Chapter 11 Recycling
Index

A bottom cover drives 17, 19

AC adapter and battery light, removal 25
identifying 6 spare part number 17, 25 E
AC adapter, spare part numbers 20 buttons electrostatic discharge 22
action keys power 10 equipment guidelines 24
airplane mode 12 esc key, identifying 11
help 12 C
identifying 11, 12 cables 17 F
keyboard backlight 12 cables, service considerations 21 fan
mute 12 camera spare part number 16
next track 12 identifying 7 fans
pause 12 camera light, identifying 7 removal 31
play 12 camera, product description 1 spare part number 31
screen brightness 12 camera/microphone module fingerprint reader
speaker volume 12 spare part number 48 spare part number 16
switch screen image 12 caps lock light, identifying 9 fingerprint reader assembly
using 12 components removal 35
airplane mode key 12 bottom 13 spare part number 35
antenna display 7 fingerprint reader, identifying 5
removal 52 keyboard area 8 fn key, identifying 11
spare part number 18, 53 left side 6
audio right side 5 G
adjusting volume 12 computer components 15 Get Help in Windows 10 action key
audio, product description 2 computer specifications 67 12
audio-out (headphone)/audio-in connector, power 6 graphics, product description 1
(microphone) combo jack, connectors, service considerations grounding guidelines 22
identifying 5 21 guidelines
control zone 8 equipment 24
B grounding 22
backup, creating 59 D packaging 23
backups 59 display assembly transporting 23
battery components 18 workstation 23
removal 27 removal 45
spare part number 17, 27 spare part numbers 45 H
bezel display back cover, spare part hard drive
removal 46 numbers 19 precautions 22
spare part numbers 18, 46 display components 7 product description 1
BIOS display panel HDMI port
determining version 57 removal 48 identifying 6
downloading an update 58 spare part numbers 18, 50 HDMI-to-VGA adapter, spare part
starting the Setup Utility 57 display panel cable number 20
updating 57 removal 51 heat sink
Bluetooth label 14 spare part numbers 18, 52 removal 32
boot order, changing 60 display panel, product description 1 spare part numbers 16, 32
bottom components 13 display specifications 68

Index 77
 hinge caps lock 9 power requirements, product
removal 51 mute 9 description 2
spare part number 18, 51 power 9 processor, product description 1
hinge covers product description
spare part number 19 M audio 2
HP PC Hardware Diagnostics UEFI M.2 solid-state drive camera 1
downloading 63 specifications 69 display panel 1
starting 63 mass storage devices 19 external media cards 2
using 62 precautions 22 graphics 1
HP PC Hardware Diagnostics Windows memory module hard drive 1
downloading 61 product description 1 internal card expansion 2
installing 62 microphone keyboard 2
using 61 product description 1, 2 memory module 1
HP Recovery media MicroSD memory card reader, microphone 2
recovery 60 identifying 5 operating system 3
model name 1 ports 2
I mute light, identifying 9 power requirements 2
internal microphones, identifying 7 mute volume action key 12 processors 1
product name 1
J N security 3
jacks next track action key 12 serviceability 3
audio-out (headphone)/audio-in solid-state drive 1
(microphone) 5 O storage 1
operating system, product TouchPad 2
K description 3 wireless 2
keyboard product name 1
removal 54 P product name and number,
spare part number 54 packaging guidelines 23 computer 14
spare part numbers 16 pause action key 12
keyboard backlight action key 12 plastic parts, service R
keyboard, product description 2 considerations 21 recovery 59
keys play action key 12 discs 60
action 11 ports HP Recovery partition 60
airplane mode 12 HDMI 6 media 60
esc 11 product description 2 USB flash drive 60
fn 11 USB 6 recovery media
Windows 11 USB Type-C 6 creating using HP Cloud Recovery
power button, identifying 10 Download Tool 59
L power connector creating using Windows tools 59
labels identifying 6 regulatory information
Bluetooth 14 power connector cable regulatory label 14
regulatory 14 removal 36 wireless certification labels 14
serial number 14 spare part number 16, 36 Remote HP PC Hardware Diagnostics
service 14 power cord UEFI settings
wireless certification 14 requirements for all countries customizing 64
WLAN 14 71 using 64
left control zone, identifying 8 requirements for specific removal/replacement
left side components 6 countries and regions 72 preliminaries 21
lights set requirements 71 procedures 25
AC adapter and battery 6 spare part numbers 20 restoring 59
camera 7 power lights, identifying 9

78 Index
right control zone, identifying 8 top cover with keyboard WLAN label 14
right side components 5 spare part numbers 16 WLAN module
rubber feet TouchPad removal 28
removal 25 removal 38 spare part numbers 16, 28
spare part number 25 spare part number 16, 38 workstation guidelines 23
Rubber Foot Kit, spare part number TouchPad bracket
17, 20 removal 38
spare part number 16
S TouchPad cable
screen brightness action keys 12 spare part number 16, 38
Screw Kit, spare part number 20 TouchPad zone, identifying 8
security cable slot, identifying 6 TouchPad, product description 2
security, product description 3 transporting guidelines 23
serial number, computer 14 traveling with the computer 14
service considerations
cables 21 U
connectors 21 USB board
plastic parts 21 removal 34
service labels, locating 14 spare part number 16, 34
serviceability, product description 3 USB board cable
slots spare part number 16
memory card reader 5 USB port, identifying 6
security cable 6 USB Type-C port, identifying 6
solid-state drive
product description 1 V
removal 30 vents, identifying 13
spare part numbers 17, 30 volume
speaker volume action keys 12 adjusting 12
speakers mute 12
identifying 10
removal 41 W
spare part number 16, 41 webcam/microphone module
special keys, using 11 removal 48
specifications webcam/microphone module cable
computer 67 spare part numbers 18
display 68 Windows
M.2 solid-state drive 69 backup 59
storage, product description 1 recovery media 59
switch screen image action key 12 system restore point 59
system board Windows key, identifying 11
removal 43 Windows tools, using 59
spare part numbers 16, 43 wireless antenna
system restore point, creating 59 removal 52
spare part number 18, 53
T wireless certification label 14
tools required 21 wireless, product description 2
top cover WLAN antenna
removal 54 removal 52
spare part number 54 spare part number 18, 53
WLAN antennas, identifying 7
WLAN device 14

Index 79
80 Index