Scribd
Upload
50 views9 pages

Electronics Workshop Recap

The document describes a 2-day workshop where students learned about op-amps, timers, and circuit design. They gained hands-on experience building circuits using breadboards and measuring outputs with equipment. Components, kits, refreshments and certificates were provided. Financial assistance was received and positive feedback was collected.

Uploaded by

prof nk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
50 views9 pages

Electronics Workshop Recap

The document describes a 2-day workshop where students learned about op-amps, timers, and circuit design. They gained hands-on experience building circuits using breadboards and measuring outputs with equipment. Components, kits, refreshments and certificates were provided. Financial assistance was received and positive feedback was collected.

Uploaded by

prof nk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 9

RNS INSTITUTE OF TECHNOLOGY 

(AICTE Approved, VTU Affiliated and NAAC A Grade Accredited)  


(UG programs - ECE, CSE, ISE, EIE and EEE have been
accredited by NBA for the Academic years 2022-2025)  
 
DEPARTMENT OF ELECTRONICS AND COMMUNICATION 
ENGINEERING 
 
WORKSHOP REPORT 

CIRCUIT DESIGN USING 555 TIMER AND OPAMP


DAY1-(28th Jan) 

The students learnt all the basics about opamp, IC pin


diagrams, resistors, voltage . Then they learnt about CRO and
how to use CRO for measuring output. Then they practically
measured the frequency output using CRO. And the rigged the
circuit on bread  board and viewed the output after every single
stage. Summarizing they learnt all the basics and practically
rigging up the circuit and measuring the output using CRO. 
DAY2-(29th Jan) 

The students enthusiastically learnt how the bread board


connection works and they used the knowledge that they gained
on day1 for connection of the components on the bread board.
With the help of the coordinators they learnt how soldering is
done and finally they were able to see the output of the given
opamps .At the end quiz was organized were we tested the
knowledge gained by the students on both the days.The
workshop was successfully completed with the guidance of
Narendra Kumar Sir.  
Resource persons from Robotronics Team:   
Raghavendra Anil
Aryan KV
Dhruthi prakash
Nirmala
Aishwarya B M
Nikhil Nadig
Anirudh R
Arpitha .P 
Dinesh 
Dhruthi R
Anusha
Power supply Kit : collected 150 rs per group 30 X 150=4500 

ITEMS   QUANTITY RATE COST  


IC 741 2 13 26
IC 555 2 10 20
IR SENSOR 1 38 38
BOARD
LDR 1 6 6
RESISTORS BOX 1 38 38
CONNECTING 1 30 30
WIRES PACK
BUZZER 1 20 20
POT 100K 1 10 10
TRIMMER
LED 2 1 2
CAPACITORS 2 1 2
TOTAL 193

Expenditure: 
SL .N Items  QTY  Amount 
O 
1.  Components  30 5790
  KitsX193 
2.  Refreshment  2X10X70  1400 
   
3.  Certificates   65 X 6 390
 
4 MARKER PEN 3 60

    TOTAL = 7640

Gross financial assistance from IETE 7640- 4500=3140 Rs


Feedback: 

   

 
Quiz Result: 
 
Workshop photos :
 
 
 
List of participants  and attendance 

You might also like