Scribd
Upload
93 views5 pages

I200 Series

This guide summarizes the assembly of a Giada i200 series barebone PC. It warns that electrostatic discharge can damage components and recommends wearing an anti-static wrist strap. It describes removing the bottom panel and CPU fan to access the RAM, SSD, WiFi and SIM card slots. RAM must be DDR3L 1.35V type. SSD inserts into an MSATA slot and WiFi/3G modules into mini PCIe slots. Antennas connect to the wireless module and SIM card inserts if needed. Reassembly involves replacing panels and fans.

Uploaded by

Урош ypow ypoc
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
93 views5 pages

I200 Series

This guide summarizes the assembly of a Giada i200 series barebone PC. It warns that electrostatic discharge can damage components and recommends wearing an anti-static wrist strap. It describes removing the bottom panel and CPU fan to access the RAM, SSD, WiFi and SIM card slots. RAM must be DDR3L 1.35V type. SSD inserts into an MSATA slot and WiFi/3G modules into mini PCIe slots. Antennas connect to the wireless module and SIM card inserts if needed. Reassembly involves replacing panels and fans.

Uploaded by

Урош ypow ypoc
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Giada i200 Series Assembly Guide

Thank you for choosing Giada product. In such an epoch of PC development, we launched Giada
Barebone which is characterized by the mini shape, vogue and ultra-thin structure, environment
friendly, Giada will allow you to undergo new experience in the field. This Guide shows you how to
do installation and uninstallation quickly and correctly.

WARNING:
This motherboard contains static-sensitive components and should be handled with care. Failure to employ
adequate anti-static measures can cause partial or complete device failure, performance degradation, or
reduced operating life. The battery must be replaced with the correct type of lithium cell battery; otherwise
there is a risk of damage to the motherboard. To avoid electrostatic discharge (ESD) damage upon handling
this product, it is strongly recommended that you wear a grounded wrist strap or other static dissipating
device.

CONTENT:
Memory, SSD, Wireless Module and MINI SIM Card installation
Remark: The picture shown in this document is only a model of our series products, the actual
object is subject to change depends on the model you purchase.
Part 1. Appearance

The Front Panel.

USB3.0 USB3.0 Power Switch LED

1x 3.5mm jack for extended infrared


sensor and extended Power Switch

The Back Panel.

For antenna
DC-IN Rj45
Display Port HDMI 2*USB3.0 Audio out & Mic in
For antenna Clear CMOS JAHC Switch combo jack

Downloaded from www.Manualslib.com manuals search engine


The Left Panel.

COM

Part 2. Chassis disassembly

Unscrew (anti-clockwise) 2 screws


from bottom panel of the PC.

Push away the bottom panel.

Downloaded from www.Manualslib.com manuals search engine


Part 3. RAM/SSD/WIFI/3G assembly

Unscrew (anti-clockwise) 2 screws


from the CPU Fan and remove the
Acetate tape.

Remove the CPU FAN and then you


can install the RAM (only support
DDR3L 1.35V module).
MASK

After installed the RAM, you need to


tear off the mask of the 3M tape.

Reassemble the CPU FAN and the


black Acetate tape.
Fix (clockwise) the CPU FAN with 2
screws.

Downloaded from www.Manualslib.com manuals search engine


Install the SSD module to the black
MSATA slot and make sure it is locked
with one screw.

Insert the WIFI or 3G module to the


white Mini PCIE slot, make sure it is
locked with 1 screws.

Connect two antenna cables to the


Wireless module.

Insert Mini SIM Card to the slot as


the picture shown if need.

Downloaded from www.Manualslib.com manuals search engine


Part 4. Chassis assembly

Push back the top panel and fix it.

Paste on four Circular Foot-paddings


as the picture shown if need.

Fix WiFi antennas or 3G antenna.

Then the whole installation is done.

Downloaded from www.Manualslib.com manuals search engine

You might also like