40 Ton Telescopic Boom Crawler Crane

8012
SPECIFICATION SHEET NO. 477-03/11
GENERAL DATA COUNTERWEIGHT
10,000 LB (4,540 kg) single piece counterweight can be removed and
CRANE CAPACITY 40 ton at 12 feet
installed via a pendant attached to the boom
(36t at 3.6m)
BOOM 3-section, WINCHES
39’0” – 90’0” Planetary geared single-speed winch includes a bent axis hydraulic
(11.9 m – 27.4 m) motor, multi-disc internal brake, counterbalance valve, grooved drums
DIMENSION and cable follower. Drum rotation indicator is included (complete winch
Overall Length 48’4” (14.73 m) performance specs on Page 4)
• Main Winch
Overall Width (tracks extended) 18’4” (5.59 m) - Rope Diameter and Length: 5/8” x 530 ft (16 mm x 162 m)
Overall Width (tracks retracted) 12’0” (3.66 m) - Single line pull: 15,630 lb (69.5 kN)(first layer)
Overall Height 10’0” (3.05 m) - Single line speed: 247 ft/min (75 m/min)(4th layer)
• Auxiliary Winch
MASS
- Rope Diameter and Length: 5/8” x 350 ft (16 mm x 107 m)
Gross Vehicle Mass 86,904 LB - Single line pull: 15,630 lb (69.5 kN)(first layer)
(Standard Equipment Package) (39,420 kg) - Single line speed: 247 ft/min (75 m/min)(4th layer)
PERFORMANCE
Travel Speed 0.78 mph – 1.29 mph TRAVEL
(1.3 km/h – 2.1 km/h) Each side frame contains a pilot controlled, two-speed track drive with
hydraulic axial piston motor and parking brake. Travel system provides
Gradability 78%
skid steering and counter rotation.
• Low travel speed: 0.78 mph (1.3km/h)
crane specification • High travel speed : 1.29 mph (2.1 km/h)
• Gradeability (unladen): 78%
MODEL
8012 SWING
Gear motor driving a planetary gear reducer with a shaft mounted
CAPACITY pinion, external gear shear ball slew bearing bolted to the
40 ton at 12 feet (36t at 3.6m) superstructure and the carbody allows the superstructure to rotate 360°
• Swing Speed: 0 – 2.2 rpm
BOOM • Swing Parking Brake: Spring applied failsafe brake with hydraulic
3-section full power synchronized telescoping boom. Synchronized release that is controlled from the operators cab
telescoping system consists of double acting hydraulic cylinder with • Swing Service Brake: Hydraulically applied, controlled through foot
load holding valves and extension and retraction cables. actuated pedal
• Retracted Length: 39’0” (11.9 m) • House Lock System: 2-position, manually pinned
• Extended Length: 90’ 0” (27.4 m)
• Extension Time: 102 s LOAD MOMENT INDICATOR
• Elevating Angles: -1° to 78° Standard Rated Capacity Limiter and Anti-Two Block system
• Elevating Time: 64 s • Control function shutdown. Audible and visual warnings
• Boom Head: Four, 15 inch (381 mm) diameter cast nylon sheaves • LCD screen provides a continuous display of working boom length,
on heavy-duty roller bearings. boom angle, working load radius, tip height, parts-of-line (operator
set), machine track configuration, relative load moment, maximum
AUXILIARY BOOM HEAD permissible load and actual load.
Quick reeve, single 19 inch (483 mm) diameter high-strength, cast • Anti-two block weight allows quick reeving of hook block
nylon sheave mounted on a heavy-duty roller bearing.
• Hook Block: 40 ton (36 t) hook block – Four - 19 inch (483 mm) FRAME
diameter sheaves mounted on heavy duty roller bearings with The frame is an all-steel, welded structure, precision machined to
swivel hook and safety latch. accept attachment of the boom and swing components.
• Headache Ball: 12 ton (11) ball includes a swivel hook with
a safety latch
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

OPERATORS CAB HYDRAULIC SYSTEM

Fully-enclosed, air conditioned all-steel modular cab with lockable • Hydraulic Pumps: Two high pressure, variable axial piston pumps
swinging door, acoustical lining, anti-slip floor and tinted safety glass. with load sense and power limiting control for crane functions.
• Rear view cameras are appropriately located as are three remote • Directional Valves: Multiple pressure and flow compensated valves
control work lights. with integrated relief valves controlled by hydraulic pilot signals.
• Vent window in the rear of the cab. • Pump output: 154 gpm (583 l/min) @ 2100 RPM engine speed.
• Grab bars and steps are located for easy access to the cab. 4,800 psi (330 bar) maximum pressure
• Defroster, heater, circulating fan • Reservoir: 300 gallon (568 liter) capacity, spin-on filler/ breather,
• 2-speed windshield wiper, top glass wiper sight gauge, cleanout, and sump drain.
• Six-way adjustable fabric seat with headrest, seat belt • Filtration: 5 micron, full flow tank mounted return filters with
• Dome light electrical clogging indicator. 5 micron pilot oil in-line pressure filter
• Dry-chemical fire extinguisher • Diagnostic Ports: Provided for system, load sense, and pilot
• Two-way armrest mounted hydraulic joysticks control swing, boom pressure
extend, main winch, and boom hoist. Hydraulic foot pedals control
the travel and swing service brake functions. OPTIONAL EQUIPMENT
• Seat and armrest termination switches immediately disable all • Boom Extension: Lattice type, swing away
hydraulic functions as the operator rises from the seat or lifts the left - Length: 30 feet (9.1m)
hand armrest. - Head: Two, 19-inch (483 mm) diameter cast nylon sheaves on
Dash instrumentation: tachometer, voltmeter, oil pressure gauge, heavy-duty roller bearings
temperature gauge, hour meter and fuel gauge. Indicators are provided - Max. Lifting Height: 121 ft (36.9 m)
for crane level, load moment, drum rotation, air filter restriction, • Boom Jib: Lattice type, swing away, stores along boom extension
hydraulic oil temperature and filter restriction, engine oil pressure and - Length: 20 feet (6.1m)
temperature. - Offset Angles: 15° & 30°
- Max. Lifting Height: 140 feet (42.7 m)
ENGINE • Track Shoes: 30 inch (762 mm) 3-bar semi grouser
• Make/ Model: Cummins QSB 6.7 • Track Shoes: 31.5 inch (800 mm) flat shoe
• Type: 6 Cylinder, Water cooled, 4 Cycle • Auger Ready Package: Includes hoses, fasteners and stowage
• Aspiration: Turbocharged and Aftercooled bracket assembly mounted to the base section of the boom with a
• Max.Output: 260 hp (194 kw) @ 2200 RPM flow capability of 34 gpm (130 l/min)
• Max Torque: 728 Lb-ft (987 Nm) @ 1500 RPM • Complete Auger Package: Adds a two speed auger motor/gear box
• Piston Disp: 6.7 liter and one 60 inch (1.52 m) kelly bar to the Auger Ready Package.
• Bore x Stroke:107mm x 124mm • Tool Circuit: Provides 5 gpm (23 l/min) and 10 gpm (45 l/min) at
• Emission Cert: U.S. EPA Tier 3, Euromot Stage IIIA 2,500 PSI (176 bar) through a 50 foot (15.2m) twin hose reel with
• Alternator: 130 amp quick disconnect fittings to operate open center tools.
• Free Fall Hoists: All winches are available in controlled free fall
ELECTRICAL SYSTEM configurations.
12 VDC • Cold Weather Packages: Cold weather options are available for
operation to -40°C (Consult factory for application support)
FUEL SYSTEM • Work Platform: Model WP750 – 36 in x 72 in (0.9m x 1.8m) , all
• Capacity: 80 gallon (378 liter) steel, welded, two person platform with maximum capacity of 750 lbs
• Filtration: Inline fuel/water separator and engine mounted fuel filter (340 kg).
• Pole Claw: Heavy-duty pole claw with hydraulic clamp and tilt.
SIDE FRAMES • Access walkways
Two welded steel side frames are paired with a track group. The side • Radio control package.
frames extend and retract hydraulically and are controlled from the cab. • Rotation resistant wire rope.
• Track Rollers: Two top and thirteen bottom sealed rollers on each
track frame Idler: Oil filled, self lubricating with spring type tensioner
• Track Shoes: 36 inch (900 mm), 3-bar semi grouser

2
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

MAIN WINCH
Planetary geared two-speed winch includes a bent axis, variable displacement hydraulic motor, a multi-disc internal brake, grooved drum and cable follower.
Wire Rope: 530 ft (162 m) 5/8 in (16 mm) 6 x 37 EIPS, IWRC, RRL. Line pulls are not based on wire rope strength. Drum rotation indicator is standard.

Rope Maximum Line Pull Full Load Line Speed High Line Speed Layer Total
Layer lb kn ft/min m/min ft/min m/min ft m ft m
1 15,630 69.5 185 56 392 119 104 32 104 32
2 14,070 62.6 206 63 436 133 116 35 220 67
3 12,790 56.9 227 69 480 146 127 39 347 106
4 11,720 52.1 247 75 523 159 139 42 486 148
5 10,820 48.1 268 82 567 173 151 46 637 194
6 10,050 44.7 289 88 611 186 162 50 799 244

Auxiliary WINCH
Planetary geared two-speed winch includes a bent axis, variable displacement hydraulic motor, a multi-disc internal brake, grooved drum and cable follower.
Wire Rope: 350 ft (107 m) 5/8 in (16 mm) 6 x 37 EIPS, IWRC, RRL. Line pulls are not based on wire rope strength. Drum rotation indicator is standard.

Rope Maximum Line Pull Full Load Line Speed High Line Speed Layer Total
Layer lb kn ft/min m/min ft/min m/min ft m ft m
1 15,630 69.5 185 56 392 119 104 32 104 32
2 14,070 62.6 206 63 436 133 116 35 220 67
3 12,790 56.9 227 69 480 146 127 39 347 106
4 11,720 52.1 247 75 523 159 139 42 486 148

Machine Weights
STANDARD CRANE WITH 3 SECTION 80 ft 0 in (24.38 m) BOOM, 59,980 lb 27,210 kg
1 PIECE COUNTERWEIGHT & 30 in (762 mm) TRACK SHOES
Crane Less Counterweight 48,480 lb 21,990 kg
Counterweight 10,000 lb 4,536 kg
Track Frames, 2 pieces 11,800 lb (5,352 kg) each 23,600 lb 10,705 kg
OPTIONAL EQUIPMENT
30 ft (9.14 m) Lattice Extension 1,700 lb 771 kg
20 ft (6.10 mm) Jib (connects to head of Lattice Extension ONLY) 700 lb 318 kg
Auxiliary Nose Sheave 210 lb 95 kg
Auxiliary Winch with Standard Rope 685 lb 311 kg
12 ton (11 mt) Headache Ball 404 lb 183 kg
40 ton (36 mt) Hook Block 1,200 lb 544 kg
Auger Ready Package 440 lb 200 kg
Complete Auger Package 1,520 lb 690 kg
60 in (1.52 m) Auger Kelly Bar 120 lb 54 kg
72 in (1.83 m) Auger Kelly Bar 140 lb 64 kg

* Deduction from Standard Crane Weight

3
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

DIMENSIONS

Widths, Weights, and Ground Pressures*

Shoe Overall Width Ground Working
Area
Width Retracted Extended Pressure Weight
24 in 11 ft 0 in 17 ft 2 in 9,360 in² 8.9 psi 82,950 lb
(609 mm) (3.35 m) (5.23 m) (6.04 m²) (0.62 kg/cm²) (37,630 kg)
30 in 11 ft 6 in 17 ft 8 in 11,700 in² 7.3 psi 84,934 lb
(762 mm) (3.51 m) (5.39 m) (7.55 m²) (0.51 kg/cm²) (38,530 kg)
36 in 12 ft 0 in 18 ft 4 in 14,040 in² 6.2 psi 86,904 lb
(900 mm) (3.66 m) (5.59 m) (9.06 m²) (0.44 kg/cm²) (39,420 kg)
* Crane equipped with: 80 ft boom, extension, jib, 40 ton hook block, 12 ton headache ball

4
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

90 ft main boom, 30 ft extension & 20 ft jib

60 in
(1.5 m)

60 in
(1.5 m)

60 in
(1.5 m)

60 in
(1.5 m)

CAUTION: THESE CHART VALUES ARE ONLY A GUIDE AND MUST NOT BE USED TO OPERATE THE CRANE.
USE ONLY THE IN CAB LOAD CHARTS AND OPERATORS MANUAL FURNISHED WITH THE CRANE.
5
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

LOAD CHARTS

360 DEGREE RATING - LOADS IN lb x 1000

MAIN BOOM with TRACKS FULLY EXTENDED

10,000 lb COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (ft) RADIUS
(ft) 39.0 48.0 56.0 65.0 73.0 82.0 90.0 (ft)
80.0 41.5 40.0
10 10
70.9° 74.4° 76.8°
80.0 39.0 37.0 36.0
12 12
67.7° 71.9° 74.7° 76.8°
66.0 35.0 34.5 34.0 33.0 32.0
15 15
62.8° 68.0° 71.5° 74.0° 75.9° 77.4°
39.8 34.0 33.0 27.0 26.0 25.0 24.5
20 20
53.9° 61.2° 65.9° 69.3° 71.8° 73.8° 75.4°
26.6 27.0 27.0 26.0 25.0 24.0 20.0
25 25
43.9° 53.9° 60.1° 64.4° 67.6° 70.1° 72.0°
19.5 19.7 19.9 19.5 19.0 18.5 18.0
30 30
31.3° 45.9° 53.9° 59.3° 63.3° 66.3° 68.6°
14.9 15.2 15.4 15.5 15.6 15.6 15.7
35 35
3.8° 36.4° 47.2° 53.9° 58.7° 62.3° 65.1°
12.1 12.3 12.4 12.4 12.5 12.5
40 40
23.7° 39.5° 48.1° 53.9° 58.2° 61.6°
10.0 10.1 10.2 10.2 10.2
45 45
30.3° 41.7° 48.9° 54.0° 57.8°
8.2 8.3 8.4 8.5 8.5
50 50
16.7° 34.3° 43.3° 49.4° 54.0°
7.0 7.1 7.1 7.1
55 55
25.0° 37.1° 44.5° 49.9°
5.9 6.0 6.0 6.0
60 60
8.4° 29.8° 39.2° 45.5°
5.0 5.1 5.1
65 65
20.1° 33.1° 40.8°
4.3 4.3
70 70
25.7° 35.5°
3.7 3.7
75 75
15.2° 29.5°
3.1
80 80
21.9°
2.6
85 85
9.4°

* Capacity based on maximum obtainable boom angle.

° Boom angles are stated in degrees.

NOTE: Capacities appearing above the bold line are based on structural strength; tipping should not be relied upon as a capacity limitation.
Capacities appearing below the bold line are based on stability and do not exceed 75% of tipping.
CAUTION: THESE CHART VALUES ARE ONLY A GUIDE AND MUST NOT BE USED TO OPERATE THE CRANE.
USE ONLY THE IN CAB LOAD CHARTS AND OPERATORS MANUAL FURNISHED WITH THE CRANE.

6
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

LOAD CHARTS

360 DEGREE RATING - LOADS IN lb x 1000

MAIN BOOM 30’ EXTENSION & 20’ JIB

with TRACKS FULLY RETRACTED with TRACKS FULLY EXTENDED
10,000 lb COUNTERWEIGHT 10,000 lb COUNTERWEIGHT
MAIN BOOM LENGTH 30’ EXTENSION 20’ JIB
(ft)
RADIUS (ft) 39.0 39.1 to 90.0 RADIUS (ft) Total Boom Length (ft) Jib Offset Angles
Boom Boom
10 70.0 40.0 10 Angle 69.0 to Angle
> 112.0 0° 15° 30°
12 50.0 36.0 12 112.0
14 39.0 33.0 14 78º 18.0 18.0 6.7 4.0 2.2 78º
16 31.5 31.5 16 75º 13.5 13.6 6.5 4.0 2.1 75º
18 26.0 26.0 18 72º 11.5 11.5 5.3 3.5 2.0 72º
20 22.0 22.0 20 70º 10.1 10.1 4.9 3.2 1.9 70º
22 19.0 19.0 22 68º 8.9 8.8 4.4 3.0 1.8 68º
24 16.5 16.5 24 65º 8.0 8.0 3.9 2.8 1.8 65º
26 14.4 14.4 26 62º 7.2 5.8 3.3 2.6 1.7 62º
28 12.7 12.7 28 60º 6.7 5.0 3.0 2.4 1.7 60º
30 11.2 11.2 30 58º 6.1 4.3 2.2 1.9 1.4 58º
32 10.1 10.1 32 55º 5.8 3.5 1.6 1.3 1.0 55º
34 9.1 9.1 34 52º 5.3 2.8 0.8 0.6 0.4 52º

36 8.4 8.4 36 50º 5.1 2.5 0.5 0.3 0.2 50º

48º 4.8 2.1 48º
38 7.6 7.6 38
45º 4.6 1.7 45º
40 6.9 6.9 40
42 6.3 6.3 42
44 5.9 5.9 44 ZERO DEGREE BOOM ANGLE WEIGHT REDUCTIONS
46 5.4 5.4 46 MAXIMUM CAPACITY LOAD HANDLING DEVICES
48 4.9 4.9 48 with TRACKS FULLY EXTENDED HOOKBLOCK: 40 Ton - 4 Sheave 1200 lbs
50 4.5 4.5 50 10,000 lb COUNTERWEIGHT OVERHAUL BALL: 12 Ton w/Swivel 220 lbs
52 4.2 4.2 52 OPTIONAL HANDLING DEVICES
BOOM RADIUS LOAD (lbs) BOOM
LENGTH (ft) (ft) (x 1000) LENGTH (ft) 30 ft. Extension - Stowed** 350 lbs
54 3.8 3.8 54
30 ft. Extension - Erected** 2000 lbs
56 3.5 3.5 56
39.0 35.0 14.9 39.0 30 ft. Ext. and 20 ft. Jib - Stowed** 750 lbs
58 3.2 3.2 58 48.0 44.0 10.6 48.0 30 ft. Ext. and 20 ft. Jib - Erected** 3500 lbs
60 2.9 2.9 60 56.0 52.0 7.9 56.0 Auxillary Nose Sheave** 250 lbs
60 2.3 2.3 60 65.0 61.0 5.8 65.0 ** Reduction of main boom capacities.
73.0 69.0 4.5 73.0
82.0 78.0 3.3 82.0
90.0 86.0 2.5 90.0

NOTE: Capacities appearing above the bold line are based on structural strength; tipping should not be relied upon as a capacity limitation.
Capacities appearing below the bold line are based on stability and do not exceed 75% of tipping.
CAUTION: THESE CHART VALUES ARE ONLY A GUIDE AND MUST NOT BE USED TO OPERATE THE CRANE.
USE ONLY THE IN CAB LOAD CHARTS AND OPERATORS MANUAL FURNISHED WITH THE CRANE.

7
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

LOAD CHARTS

360 DEGREE RATING - LOADS IN lb x 1000

AUXILIARY NOSE SHEAVE with TRACKS FULLY EXTENDED

10,000 lb COUNTERWEIGHT
MAIN BOOM LENGTH (ft)
RADIUS (ft) RADIUS (ft)
39.0 48.0 56.0 65.0 73.0 82.0 90.0
11.0 11.0 11.0
10 10
70.9° 74.4° 76.8°
11.0 11.0 11.0 11.0
12 12
67.7° 71.9° 74.7° 76.8°
11.0 11.0 11.0 11.0 11.0 11.0
15 15
62.8° 68.0° 71.5° 74.0° 75.9° 77.4°
11.0 11.0 11.0 11.0 11.0 11.0 11.0
20 20
53.9° 61.2° 65.9° 69.3° 71.8° 73.8° 75.4°
11.0 11.0 11.0 11.0 11.0 11.0 11.0
25 25
43.9° 53.9° 60.1° 64.4° 67.6° 70.1° 72.0°
11.0 11.0 11.0 11.0 11.0 11.0 11.0
30 30
31.3° 45.9° 53.9° 59.3° 63.3° 66.3° 68.6°
11.0 11.0 11.0 11.0 11.0 11.0 11.0
35 35
3.8° 36.4° 47.2° 53.9° 58.7° 62.3° 65.1°
11.0 11.0 11.0 11.0 11.0 11.0
40 40
23.7° 39.5° 48.1° 53.9° 58.2° 61.6°
10.0 10.1 10.2 10.2 10.2
45 45
30.3° 41.7° 48.9° 54.0° 57.8°
8.2 8.3 8.4 8.5 8.5
50 50
16.7° 34.3° 43.3° 49.4° 54.0°
7.0 7.1 7.1 7.1
55 55
25.0° 37.1° 44.5° 49.9°
5.9 5.9 6.0 6.0
60 60
8.4° 29.8° 39.2° 45.5°
5.0 5.1 5.1
65 65
20.1° 33.1° 40.8°
4.3 4.3
70 70
25.7° 35.5°
3.7 3.7
75 75
15.2° 29.5°
3.1
80 80
21.9°
85 2.6 85
9.4°
° Boom angles are stated in degrees.

NOTE: Capacities appearing above the bold line are based on structural strength; tipping should not be relied upon as a capacity limitation.
Capacities appearing below the bold line are based on stability and do not exceed 75% of tipping.
CAUTION: THESE CHART VALUES ARE ONLY A GUIDE AND MUST NOT BE USED TO OPERATE THE CRANE.
USE ONLY THE IN CAB LOAD CHARTS AND OPERATORS MANUAL FURNISHED WITH THE CRANE.

8
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

LOAD CHARTS
WP-750 WORK PLATFORM
Installed on MANTIS MODEL 8012
as originally manufactured and equipped by Tadano Mantis Corporation

Limits of operation: Maximum load capacity = 750 lb Maximum radius when mounted on main boom = 78 ft

CAUTION: THESE CHART VALUES ARE ONLY A GUIDE AND MUST NOT BE USED TO OPERATE THE CRANE.
USE ONLY THE IN CAB LOAD CHARTS AND OPERATORS MANUAL FURNISHED WITH THE CRANE.

9
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

MANTIS MODEL 8012

WIRE ROPE LINE PULL CAPACITIES
PARTS MAIN AUX PARTS MAIN
OF WINCH WINCH OF WINCH
LINE (pounds) (pounds) LINE (pounds)
1 11,771 11,771 5 58,855
2 23,542 23,542 6 70,626
3 35,313 N/A 7 82,397
4 47,084 N/A 8 94,168
5/8 inch diameter wire rope, 6 x 37 Class, EIP, IWRC

PLEASE READ, UNDERSTAND, AND FOLLOW THE MANUALS FURNISHED WITH THE CRANE (OPERATORS AND SAFETY)
AS WELL AS THE CAPACITY LIMITATIONS AND GENERAL CONDITIONS LISTED BELOW PRIOR TO
OPERATION OF THE CRANE. FAILURE TO DO SO MAY RESULT IN AN ACCIDENT.

This MANTIS CRANE as manufactured by Tadano Mantis Corporation meets the requirements of ASME B30.5. Structure and stability have been
tested in accordance with SAE J1063 and SAE J765, respectively. Lifting capacities as determined by boom length, angle or radius, apply only to
machines as originally equipped by manufacturer and in a properly maintained condition. Capacities given are maximum covered by the manufac-
turers warranty and are based on a freely suspended load with NO allowance for factors as out-of-level operation, supporting surface conditions,
hazardous surroundings, experience of personnel, etc. The operator shall establish practical working loads based on prevailing operating conditions,
such as, but not limited to the above.

When making lifts where capacities may be within a zone limited by structural strength, the operator shall determine that the weight of the load is
known within plus or minus (+/-) ten percent (10%) before making lift. DO NOT lift load or extend boom without counterweight in place. Deductions
from rated capacities must be made for the weight of the hook block, hook/ball, slings, spreader bar, or other suspended equipment.

Side pull on boom is extremely dangerous and must be avoided.

DO NOT exceed manufacturers maximum specified reeving.

DO NOT use this chart if wind speed exceeds 20 mph. Consult the manufacturer for specialized load ratings.

Load radius is defined as the horizontal distance from the axis of rotation (with no load) to the center of the lifting device after load is applied.
Boom angle is the included angle between the longitudinal axis of the boom base section and the Horizontal axis, after lifting load. The boom angle
before lifting should be slightly greater than desired to account for boom deflection.

Boom angle/boom length relationships given are an approximation of the resulted load radius, which should be an accurate measurement.
Boom height dimensions are measured from ground to center of lower boom head sheave.

It is permissible to attempt to telescope boom with a load within the limits of rated capacities. However, boom angle system hydraulic pressure, and/
or boom lubrication may affect operation.

It is permissible to travel with loads within the rated capacity of the crane. Travel speeds should be greatly reduced to reflect terrain limitations and
minimize dynamic loads applied to the crane structure.

CAUTION: THESE CHART VALUES ARE ONLY A GUIDE AND MUST NOT BE USED TO OPERATE THE CRANE.
USE ONLY THE IN CAB LOAD CHARTS AND OPERATORS MANUAL FURNISHED WITH THE CRANE.

10
8012
40 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET NO. 477-03/11

NOTES:

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

11
 TADANO MANTIS CORPORATION 1705 Columbia Avenue • Franklin, TN 37064 USA • Toll-Free: 1-800-272-3325 • Fax: 615-790-6803 • mantiscranes.com

SPECIFICATION SHEET NO. 477-03/11