Roofing Products

Lysaght Custom Orb® Lysaght Klip-Lok 700 Hi-Strength®

Lysaght Custom Blue Orb® Lysaght Klip-Lok 406®
Curving & Bullnosing of Custom Blue Orb® Lysaght Longline 305®
Lysaght Trimdek® Lysaght Flatdek®
Lysaght Spandek® Lysaght Rooftrak (Walkway system)

New South Wales

 New South Wales/ACT

Custom Orb
Finish BMT mm $/m2
16 mm
ZINCALUME® steel 0.42 24.84
762 mm cover
Galvanised Z450 0.42 35.49
COLORBOND® steel 0.42 26.58
Minimum recommended
roof pitch = 5˚ (1 in 12) COLORBOND® steel Perforated, Corstrip – Surfmist only 0.42 46.97
COLORBOND® steel Hi-Gloss 80% 0.42 34.08
COLORBOND® steel Double Sided 0.42 36.74
Roofing

COLORBOND® steel Double Sided Hi Gloss 0.42 36.74

COLORBOND® steel Ultra 0.42 51.51
ZINCALUME® steel 0.48 31.87
COLORBOND® steel 0.48 33.73
COLORBOND® steel Ultra 0.48 54.92
COLORBOND® steel Metallic 0.48 59.89
To convert price to lineal metres multiply by 0.762
Maximum length* = 27000mm, Minimum rollformed length* = 1000mm
Notes:
1. Minimum cut back is 305mm.
2. Cutting charges apply to lengths under 1000mm and may be subject to a longer leadtime (refer page 12).
3. Cut back not available where colour underside or double-sided colour is requested.
4. Contact your local branch for price and availability of colours not shown as available on page 4 and 5 of this price list.
5. Tolerance on sheet lengths +0-10mm, width +4 - 4mm.
6. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).
7. *Variations to minimum and maximum lengths may apply at your local branch.

Fasteners – Custom Orb

Application Type Unpainted Unpainted Painted Painted
$/1000 $/100 $/1000 $/100
Steel battens up to Roof Zip R650 314.32 37.07 384.69 44.10
1.0mm BMT
Steel Purlins 1.2mm SH1235 Metal HG Hex Head 291.28 34.77 361.66 41.81
to 2.4mm BMT
Timber – Softwood Roof Zip R650 314.32 37.07 384.69 44.10

Timber – Hardwood Roof Zip R650 314.32 37.07 384.69 44.10

Notes:
1. 5 fasteners per m2. (Estimate for non-cyclonic area)

31 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Standard Flashings – Custom Orb

Product ZINCALUME® steel COLORBOND® steel
$/lm $/lm

180
Ridge Capping 26.93 25.89
180
20 20

50
Roll Top Ridge Capping 20.22 19.62
127 127
19

Roofing
300 19

*Nominate Angle
10 Tile Flashing 26.93 25.89
230 *
20
140

Apron Flashing 20.13 18.83

100 180
20
160°

20 Valley Gutter 26.93 25.89

20
180 180

200 Barge Capping 21.38 19.86

160˚ 20
70
10

190
20
50 Barge Roll Capping 19.24 24.10
2400 mm length only (Gable roll capping)

50 Barge Roll 12.22 14.79

dia.
2400mm length only

$/ea $/ea
Spear Point
43.43 43.04

Maximum length* = 8000mm, Minimum length* = 1000mm (Rolltop maximum length* = 9000mm, Minimum length* = 800mm)
Notes:
1. Refer to page 73 for the complete range of standard flashings.
2. For all other flashings that vary in dimensions from the standard range, please refer to section on Custom Flashings.
3. *Variations to minimum and maximum lengths may apply at your local branch.

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 32
 New South Wales/ACT

Translucent Sheeting – Custom Orb (Fibreglass)

Product Grams/m2 $/lm

Fibreglass 1800 (walling only) 44.85

2400 48.54

Maximum length = 12200mm, Minimum length = 900mm

Notes:
1. An extra charge will apply to lengths over 11000mm.
Roofing

2. Available in Clear and Opal.

3. 32mm Weatherlok Washer required for all translucent sheeting.
4. Please refer to page 79 for other products in the Translucent Sheeting range.

Translucent Sheeting Accessories

Product Width (mm) Length $/roll $/1000
Roofing Wire 1800mm 50m 263.63 N/A
(2 x 300 x 150mm)
Lapseal 50mm x 6mm 11.7m 64.49 N/A
75mm x 6mm 11.7m 92.77 N/A
100mm x 6mm 11.7m 118.86 N/A
Weatherlok Washer 32mm (Dia) N/A 373.01
(Fibreglass only)

Polycarbonate Sheeting – Custom Orb

Description Polycarbonate $/lm Laserlite 2000 $/lm

Custom Orb 48.46 63.10

Notes:
1. Polycarbonate Lengths: 1800, 2400, 3000, 3600, 4200, 4800, 5400, 6000 and 7200mm.
Colours: Clear, Opal, Antique Bronze, and Smoke Grey.
2. Laserlite 2000 Lengths: 1800, 2400, 3000, 3600, 4200, 4800, 5400, 6000 and 7200mm.
Colours: Bronze Tint, Classic Cream, Clear, Gumleaf, Grey Tint, Ocean Blue and Opal.

Roof Infill Strips – Custom Orb

Product Length $/ea
Custom Orb 915mm 5.89

33 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Custom Blue Orb – (Suitable for curving)

16 mm
Finish BMT mm $/m2

ZINCALUME® steel (10.5 corrugations) 0.60 40.40

762 mm cover

Galvanised Z600 (10.5 corrugations) 0.60 54.04

Minimum recommended
roof pitch = 5˚ (1 in 12)
COLORBOND® steel (10.5 corrugations) 0.60 40.59

COLORBOND® steel Ultra 0.60 POA

Roofing
To convert price to lineal metres multiply by 0.762
Maximum length = 25000mm, Minimum Rollformed length = 1000mm
Notes:
1. Minimum cut back is 305mm.
2. Cutting charges apply to lengths under 1000mm and may be subject to a longer leadtime (refer page 12)
3. Cut back not available where colour underside or double-sided colour is requested.
4. Longer lengths than listed may be available on application and should be confirmed by the designer.
5. Contact your local branch for price and availability of colours not shown as available on page 4 and 5 of this price list.
6. Tolerance on sheet lengths +10 -10mm, width +4 -4mm
7. For Custom Blue Orb accessories refer to Custom Orb accessories on pages 31-33.
8. Please specify when ordering if Custom Blue Orb is required to end lap to Custom Orb.
9. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).

Custom Blue Orb AQUAPLATE® steel – (For Tank making only)

Finish BMT mm $/m2

17 mm

Galvanised (8 corrugations) 0.60 69.60

608mm cover

17 mm
Galvanised (10 corrugations) 0.60 71.57
762 mm

Curving and Bullnosing of Custom Blue Orb

Product $ per curve
Sheet lengths over 8m or under 1m radius 24.51
Sheet lengths under 8m or over 1m radius 19.58

Notes:
1. Curved sheets longer than 8000mm, or curved heights exceeding 1000mm are subject to enquiry.
2. Additional freight charges may apply for curved product.
3. For ease of ordering, we recommend the use of our Curving Order Form.
4. Onsite curving may be available on request. An additional charge applies for this service.

Curved Flashings – for Curved Custom Blue Orb (Metal)

Product ZINCALUME® steel $/lm COLORBOND® steel $/lm
Curved Metal Apron Single Seam POA POA
Curved Metal Apron Double Seam POA POA
Curved Metal Barge Single Seam POA POA
Curved Metal Barge Double Seam POA POA

Notes:
1. Check with your local branch for price and availability of fibreglass flashings.

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 34
 New South Wales/ACT

Details required for Bullnosing Custom Blue Orb

Straight ou

Straight vertical
tside sectio

section 'SV'
n ‘SR’

Roof Pitch
'H' 'P'
Radius 'R'

Min. 110mm
Right side
Awning overall width 'A'
Left side FRONT VIEW
CR OSS SECTION
Roofing

Number of sheets required Sheet length Dimensions:

Straight outside section (SR)

Colour or finish
mm
Straight Vertical Lead in Section (SV)
Colour Topside or
mm (110mm min)
Colour Underside
Radius (R)
Direction of laying (see FRONT VIEW in right-hand column)
Left to right mm (300mm min.)
Right to left Roof Pitch (P)
Do the sheets side-lap with previously curved order? degrees
Yes If yes, template required (If using 150mm radius, minimum angle is 70˚)

No Awning overall width (A)

Does the bullnosed sheet end-lap onto a straight sheet? mm
Yes Height less vertical lead in (H)
No
mm
Have you supplied a template?
Yes
No
Is the template to be returned?
Yes
No

Notes:
1. Curved sheets longer than 8000mm, or curved heights exceeding 1000mm are subject to enquiry.
2. Additional freight charges may apply for curved product.
3. Onsite curving may be available on request. An additional charge applies for this service.

35 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Details required for Curving of Custom Blue Orb

Concave I Please tick to indicate type of curving required. Convex I

110mm

Height

Radius 0
11
m 0m
Chord Width 0m Chord Width m
11

Roofing
Radius
Height
0
110mm

Sheet length No. Required Straight section each side if radius is under
1500mm: – 110mm - min
mm
mm mm
Radius
Direction of laying
mm (300 min.) Left to right

Height Right to left

degrees Do the sheets side-lap with previously curved order?

Yes If yes, template required
Chord width
No
mm
Have you supplied a template?
Colour or Finish Yes
No
Colour Topside or
Is the template to be returned?
Colour Underside Yes
No

Additional curving types – (Please supply a detailed drawing – Price POA)

Cranked Double Curve Cyma Recta 180˚ Barrel Vault

Cranked Ridge Old Gothic Double Curve

Notes:
1. Curved sheets longer than 8000mm, or curved heights exceeding 1000mm are subject to enquiry.
2. Additional freight charges may apply for curved product.
3. Onsite curving may be available on request. An additional charge applies for this service.

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 36
 New South Wales/ACT

Trimdek
Finish BMT mm $m2
29 mm
ZINCALUME® steel 0.42 24.84
762 mm cover Galvanised Z450 0.42 35.49
COLORBOND® steel 0.42 26.58
Minimum
recommended COLORBOND ®
steel Hi Gloss 80% 0.42 34.08
roof pitch COLORBOND ®
steel Ultra 0.42 51.51
= 2˚ (1 in 30)
COLORBOND ®
steel Double Sided Hi Gloss 0.42 36.74
steel Double Sided 0.42 36.74
Roofing

COLORBOND®

ZINCALUME ®
steel 0.48 31.87
COLORBOND ®
steel 0.48 33.73
COLORBOND ®
steel Ultra 0.48 54.92
COLORBOND® steel Metallic 0.48 59.89
To convert price to lineal metres multiply by 0.762

Maximum length* 27300mm, Minimum Rollformed length* = 1000mm

Notes:
1. Minimum cut back is 305mm.
2. Cutting charges apply to lengths under 1000mm and may be subject to a longer leadtime (refer page 12)
3. Cut back not available where colour underside or double-sided colour is requested.
4. Longer lengths than listed may be available on application and should be confirmed by the designer.
5. Contact your local branch for price and availability of colours not shown as available on page 4 and 5 of this price list.
6. Tolerance on sheet lengths +0-15mm, width +4 -4mm
7. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).
8. *Variations to minimum and maximum lengths may apply at your local branch.

Fasteners – Trimdek
Application Type Unpainted Unpainted Painted Painted
$/1000 $/100 $/1000 $/100
Steel battens up to Roof Zip R650 314.32 37.07 384.69 44.10
1.0mm BMT
Steel purlins 1.2mm Auto Teks AT5550 298.61 35.52 368.97 42.56
up to 2.4mm BMT
Timber – Softwood Roof Zip R665 369.45 42.81 443.34 50.01

Timber – Hardwood Roof Zip R650 314.32 37.07 384.69 44.10

Notes:
1. 5.5 fasteners per m2. (Estimate for non-cyclonic area)

Roof Infill Strips – Trimdek

Product Length $/ea
Trimdek top 915mm 5.89
(Bottom profile shown) Trimdek bottom 915mm 5.89

37 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Standard Flashings – Trimdek

Product ZINCALUME® steel COLORBOND® steel
$/lm $/lm

170 Ridge Capping 26.93 25.89

170
30 30
*Nominate angle
10 Tile Flashing 26.93 25.89
220 *
30
140

100
Apron Flashing 20.13 18.83
170

Roofing
30

Barge Capping 21.38 19.86

190
30
70
10

20 Valley Gutter 26.93 25.89

20
180 180

Maximum length 8000mm, Minimum length = 1000mm

Notes: 1. Refer to page 73 for the complete range of standard flashings.
2. For all other flashings that may vary in dimensions from the standard range, please refer to section on Custom Flashings.

Translucent Sheeting – Trimdek

Product Grams/m2 $/lm
Fibreglass 1800 (walling only) 44.85
2400 48.54
3050 68.38
Maximum length = 12200mm, Minimum length = 900mm
Notes: 1. An extra charge will apply to lengths over 11000mm. 4. Please refer to page 79 for other products in the
2. Available in Clear and Opal. Translucent Sheeting range.
3. 32mm Weatherlok Washer required for all
translucent sheeting.

Translucent Sheeting Accessories

Product Width (mm) Length $/roll $/1000
Roofing Wire 1800mm 50m 263.63 N/A
(2 x 300 x 150mm)
Lapseal 50mm x 6mm 11.7m 64.49 N/A
75mm x 6mm 11.7m 92.77 N/A
100mm x 6mm 11.7m 118.86 N/A
Weatherlok Washer 32mm (Dia) N/A 373.01
(Fibreglass only)

Polycarbonate Sheeting – Trimdek

Description Polycarbonate $/lm Laserlite 2000 $/lm

Trimdek 48.46 63.10

Notes: 1. Polycarbonate Lengths: 1800, 2400, 3000, 3600, 4200, 4800, 5400, 6000 and 7200mm.
Colours: Clear, Opal, Antique Bronze, and Smoke Grey.
2. Laserlite 2000 Lengths: 1800, 2400, 3000, 3600, 4200, 4800, 5400, 6000 and 7200mm.
Colours: Bronze Tint, Classic Cream, Clear, Grey Tint and Opal.

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 38
 New South Wales/ACT

Spandek
Finish BMT mm $/m2
24 mm
ZINCALUME® steel 0.42 29.30
700 mm cover
COLORBOND ®
steel 0.42 31.08
COLORBOND ®
steel Hi Gloss 80% 0.42 39.41
Minimum
recommended COLORBOND ®
steel Ultra 0.42 57.37
roof pitch COLORBOND ®
steel Double Sided Hi Gloss 0.42 42.06
= 3˚ (1 in 20)
COLORBOND ®
steel Double Sided 0.42 42.06
Roofing

ZINCALUME ®
steel 0.48 37.51
COLORBOND ®
steel 0.48 35.43
COLORBOND ®
steel Ultra 0.48 62.40
COLORBOND ®
steel Metallic 0.48 64.21
To convert price to lineal metres multiply by 0.700

Maximum length = 27900mm, Minimum Rollformed length = 1000mm

Notes:
1. Minimum cut back is 305mm.
2. Cutting charges apply to lengths under 1000mm and may be subject to a longer leadtime (refer page 12)
3. Cut back not available where colour underside or double-sided colour is requested.
4. Longer lengths than listed may be available on application and should be confirmed by the designer.
5. Contact your local branch for price and availability of colours not shown as available on page 4 and 5 of this price list.
6. Tolerance on sheet lengths +0-15mm width, +4 -4mm
7. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).

Fasteners – Spandek
Application Type Unpainted Unpainted Painted Painted
$/1000 $/100 $/1000 $/100
Steel battens up to Roof Zip R650 314.32 37.07 384.69 44.10
1.0mm BMT
Steel purlins 1.2mm Auto Teks AT5550 298.61 35.52 368.97 42.56
up to 2.4mm BMT
Timber – Softwood Roof Zip R665 369.45 42.81 443.34 50.01

Timber – Hardwood Roof Zip R650 314.32 37.07 384.69 44.10

Notes:
1. 5.5 fasteners per m2. (Estimate for non-cyclonic area)

Polycarbonate Sheeting – Spandek

Description Polycarbonate $/lm Laserlite 2000 $/lm

Greca 48.46 63.10

Notes: 1. Polycarbonate Lengths: 1800, 2400, 3000, 3600, 4200, 4800, 5400, 6000 and 7200mm.
Colours: Clear, Opal, Antique Bronze, and Smoke Grey.
2. Laserlite 2000 Lengths: 1800, 2400, 3000, 3600, 4200, 4800, 5400, 6000 and 7200mm.
Colours: Bronze Tint, Classic Cream, Clear, Grey Tint, Gumleaf, Ocean Blue and Opal.
3. Not suitable for lapping with Spandek.

39 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Standard Flashings – Spandek

Product ZINCALUME® steel COLORBOND® steel
$/lm $/lm
Ridge Capping 26.93 25.89
170 170
30 30

*Nominate angle Tile Flashing 26.93 25.89

10

220 *
30

Roofing
140

Apron Flashing 20.13 18.83

100 170
30

Barge Capping 21.38 19.86

190
30
70
10

Valley Gutter 26.93 25.89

20
20
180 180

Maximum length 8000mm, Minimum length = 1000mm

Notes: 1. Refer to page 73 for the complete range of standard flashings.
2. For all other flashings that may vary in dimensions from the standard range, please refer to section on Custom Flashings.

Translucent Sheeting – Spandek (Fibreglass)

Product Grams/m2 $/lm
Fibreglass 2400 61.83
3050 69.05

Maximum length = 12200mm, Minimum length = 900mm 4. Please refer to page 79 for other products in the
Notes: 1. An extra charge will apply to lengths over 11000mm. Translucent Sheeting range.
2. Available in Clear and Opal.
3. 32mm Weatherlok Washer required for all
translucent sheeting.

Translucent Sheeting Accessories

Product Width (mm) Length $/roll $/1000
Roofing Wire 1800mm 50m 263.63 N/A
(2 x 300 x 150mm)
Lapseal 50mm x 6mm 11.7m 64.49 N/A
75mm x 6mm 11.7m 92.77 N/A
100mm x 6mm 11.7m 118.86 N/A
Weatherlok Washer 32mm (Dia) N/A 373.01
(Fibreglass only)

Roof Infill Strips – Spandek

Product Length $/ea
Spandek top 745mm 6.08
Spandek bottom 745mm 6.08

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 40
 New South Wales/ACT

Klip-Lok 700 Hi-Strength

Finish BMT mm $/m2

43 mm ZINCALUME® steel 0.42 36.64

COLORBOND® steel 0.42 40.32

700 mm cover
COLORBOND ®
steel Ultra 0.42 65.30
Minimum
recommended ZINCALUME® steel 0.48 41.04
roof pitch
0.42 = 2˚ (1 in 30) COLORBOND ®
steel 0.48 45.74
Roofing

0.48 = 1˚ (1 in 50) COLORBOND® steel Ultra 0.48 69.90

COLORBOND ®
steel Metallic 0.48 75.36

COLORBOND® steel 0.60 POA

To convert price to lineal metres multiply by 0.700

Maximum length 27000mm, Minimum length = 1000mm

Notes:
1. No cut back facility for Klip-Lok 700.
2. Longer lengths than listed may be available on application and should be confirmed by the designer.
3. Contact your local branch for price and availability of colours not shown as available on page 4 and 5 of this price list.
4. Tolerance on sheet lengths +0-15mm, width +4 -4mm
5. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).
6. Please enquire with your local branch about our mobile onsite rolling service.
®
7. COLORBOND Steel .60 subject to enquiry (mobile rollformed).

Clips – Klip-Lok 700 Hi-Strength

Product $/50 box

t
Klip-Lok 700 Hi-Strength Clips 181.59

Notes: 1.5 clips per m2 (Estimate for non-cyclonic area)

Fasteners – Klip-Lok 700 Hi-Strength

Application Type Unpainted Unpainted
$/1000 $/100

Steel up to 1.0mm BMT RZ625N Roof Zip POA POA

Steel>1.0mm BMT to 2.4mm BMT SH1220N Metal Hex Head 113.11/500 28.25

Timber-Softwood BZ5540N Batten Zip 201.06 25.47

Timber-Hardwood BZ5540N Batten Zip 201.06 25.47

Notes: 3 fasteners per clip (Estimate for non-cyclonic area)

NEED LONG LENGTH ROOFING?

Ask about our mobile roll-forming
• We didn’t invent it... We just perfected it!
• Factory Quality Output
• No Transport Hassles

Phone your nearest BlueScope Lysaght branch for more details

41 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Standard Flashings – Klip-Lok 700 Hi-Strength

Product ZINCALUME® steel COLORBOND® steel
$/lm $/lm
Ridge Capping 26.93 25.89
160 160
40 40

*Nominate angle Tile Flashing 26.93 25.89

10

210 *

Roofing
40
140

Apron Flashing 20.13 18.83

100 160
40

Barge Capping 21.38 19.86

180
40
70
10

Valley Gutter 26.93 25.89

20
20
180 180

Maximum length 8000mm, Minimum length = 1000mm

Notes:
1. Refer to page 73 for the complete range of standard flashings.
2. For all other flashings that may vary in dimensions from the standard range, please refer to section on Custom Flashings.

Translucent Sheeting – Klip-Lok 700 Hi-Strength

Product Grams/m2 $/lm
Fibreglass 2400 75.80

Maximum length = 12200mm, Minimum length = 900mm

Notes: 1. An extra charge will apply to lengths over 11000mm. 4. Please refer to page 79 for other products in the
2. Available in Clear and Opal. Translucent Sheeting range.
3. 32mm Weatherlok Washer required for all
translucent sheeting.

Translucent Sheeting Accessories

Product Width (mm) Length $/roll $/1000
Roofing Wire 1800mm 50m 263.63 N/A
(2 x 300 x 150mm)
Lapseal 50mm x 6mm 11.7m 64.49 N/A
75mm x 6mm 11.7m 92.77 N/A
100mm x 6mm 11.7m 118.86 N/A
Weatherlok Washer 32mm (Dia) N/A 373.01
(Fibreglass only)

Roof Infill Strips – Klip-Lok 700 Hi-Strength

Product Length $/ea
Klip-Lok 700 Hi-Strength Top 810mm 6.45
(Bottom profile shown)
Klip-Lok 700 Hi-Strength Bottom 810mm 6.45

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 42
 New South Wales/ACT

Klip-Lok 406
Finish BMT mm $/m2
41 mm
ZINCALUME® steel 0.42 40.18
406 mm cover
ZINCALUME ®
steel 0.48 44.96
Minimum Recommended
COLORBOND® steel 0.48 46.69
Roof Pitch
0.42 = 2˚ (1 in 30) COLORBOND® steel 0.60 POA
0.48 = 1˚ (1 in 50)
0.60 = 1˚ (1 in 50) ZINCALUME® steel 0.60 POA
Roofing

To convert price to lineal metres multiply by 0.406

Maximum length = 27000mm, Minimum length = 1000mm

Notes:
1. No cut back facility for Klip-Lok 406.
2. Longer lengths than listed may be available on application and should be confirmed by the designer.
3. Limited colour range available. Contact your local branch for price and availability of colours not shown as available on
page 4 and 5 of this price list.
4. Tolerance on sheet lengths +0-15mm, width +4 -4mm
5. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).

Clips – Klip-Lok 406

Product $/100 pk $/1000pk
KL65
Klip-Lok 406 Clips (without nails) 166.13 N/A
KL65 clip
(For KLIP-LOK 406) Nails to suit N/A 69.43
Note: 2.5 clips per m and 2 screws per clip (estimate for non-cyclonic areas).
2

Fasteners – Klip-Lok 406

Application Type Unpainted Unpainted
$/1000 $/100

Steel up to 0.75mm BMT TW1025N Type 17 Wafer Head 285.37 34.20

Steel>0.75mm to 3.0mm BMT SW1016N Metal Wafer Head 127.27 18.35

Timber-Softwood TW1035N Type 17 Wafer Head POA POA

Timber-Hardwood TW1025N Type 17 Wafer Head 285.37 34.20

43 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Standard Flashings – Klip-Lok 406

Product ZINCALUME® steel COLORBOND® steel
$/lm $/lm
Ridge Capping 26.93 25.89
160 160
40 40

10 Tile Flashing 26.93 25.89

210
deg
˚
40

Roofing
140

Apron Flashing 20.13 18.83

100 160
40

Barge Capping 21.38 19.86

180
40
70
10

Valley Gutter 26.93 25.89

20
20
180 180

Maximum length 8000mm, Minimum length = 1000mm

Notes: 1. Refer to page 73 for the complete range of standard flashings.
2. For all other flashings that may vary in dimensions from the standard range, please refer to section on Custom Flashings.

Translucent Sheeting – Klip-Lok 406

Product Grams/m2 $/lm
Fibreglass 2400 44.16

Maximum length = 12200mm, Minimum length = 900mm

Notes: 1. An extra charge will apply to lengths over 11000mm. 4. Please refer to page 79 for other products in the
2. Available in Clear and Opal. Translucent Sheeting range.
3. 32mm Weatherlok Washer required for all
translucent sheeting.

Translucent Sheeting Accessories

Product Width (mm) Length $/roll $/1000
Roofing Wire 1800mm 50m 263.63 N/A
(2 x 300 x 150mm)
Lapseal 50mm x 6mm 11.7m 64.49 N/A
75mm x 6mm 11.7m 92.77 N/A
100mm x 6mm 11.7m 118.86 N/A
Weatherlok Washer 32mm (Dia) N/A 373.01
(Fibreglass only)

Roof Infill Strips – Klip-Lok 406

Product Length Price $/ea
Klip-Lok 406 Top 810mm 6.45
(Bottom profile shown)
Klip-Lok 406 Bottom 810mm 6.45

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 44
 New South Wales/ACT

Longline 305
Finish BMT mm $/m2
48 mm
ZINCALUME® steel (plain) 0.70 79.65
305 mm cover

Minimum recommended COLORBOND® steel Plain 0.70 76.04

roof pitch
=1˚ (1 in 50) Fluted 0.70 POA
Roofing

To convert price to lineal metres multiply by 0.305 (for plain)

Maximum length 26000mm, Minimum length = 1400mm

Longline 305 Tapered

Finish BMT mm $/lm
ZINCALUME® steel 0.70 38.24
Minimum recommended
roof pitch =1˚ (1 in 50) COLORBOND® steel 0.70 36.79

Notes: Contact your local branch for availability and further details.
Maximum length 20000mm, Minimum length = 2500mm
Notes:
1. No cut back facilites for Longline 305 and Longline 305 Tapered.
2. Longer/shorter lengths than listed may be available on application and should be confirmed by the designer.
3. Contact your local branch for price and availability of colours not shown as available on page 4 and 5 of this price list.
4. Tolerance on sheet lengths +0-15mm, width +4, -4mm. Tapered longline width +5, -5mm
5. Packing sheets – $6.00/lm (Top and Bottom), $5.00/lm (Top or Bottom).

Longline 305 Clips

Product $/100

Top Fixing Clips 138.75

Start/Finish Clips 419.77

Notes: 3 clips per m2. (Estimate for non-cyclonic area)

Fasteners (Clip fixing – roof and wall application)

Application Type Unpainted Unpainted
$/1000 $/100

Steel up to 0.75mm BMT TW1025N Type 17 Wafer Head 285.37 34.20

Steel>0.75mm BMT to 3.0mm BMT SW1016N Metal Wafer Head 127.27 18.35

Timber-Softwood TW1035N Type 17 Wafer head POA POA

Timber-Hardwood TW1025N Type 17 Wafer Head 285.37 34.20

Notes: 1 fastener per clip. (Estimate for non-cyclonic area)

45 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Standard Flashings – Longline 305

Product ZINCALUME® steel COLORBOND® steel
$/lm $/lm
Ridge Capping 26.93 25.89
150 150
50 50

*Nominate angle Tile Flashing 26.93 25.89

10

Roofing
200 *
50
140

Apron Flashing 20.13 18.83

100 150
50

Barge Capping 21.38 19.86

170
50
70
10

20 Valley Gutter 26.93 25.89

20
180 180

Maximum length 8000mm, Minimum length = 1000mm, Minimum charge = 1000mm

Notes:
1. Refer to page 73 for the complete range of standard flashings.
2. For all other flashings that may vary in dimensions from the standard range, please refer to section on Custom Flashings.

NEED HELP... AFTER HOURS

Visit www.lysaght.com
For assistance with:
• Design Tools • Downloadable Brochures
• Case Studies • Installation Advice
• Product Specifications
www.lysaght.com

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 46
 New South Wales/ACT

Flatdek
Finish BMT mm $/m2
45 mm
COLORBOND® steel Double-Sided 0.42 50.23
Hi-Gloss 80% – (Underside)
COLORBOND® steel – (Topside)

250 mm cover

Minimum recommended
roof pitch = 2˚ (1 in 30)
Roofing

To convert price to lineal metres multiply by 0.250

Maximum length = 9000mm, Minimum length = 450mm

Notes:
1. Longer lengths than listed may be available on application and should be confirmed by the designer.
2. Contact your local branch for price and availability of colours not shown as available on page 7 of this price list.
3. Tolerance on sheet lengths +0-15mm, width +2 -2mm

Receiver Channel – Flatdek

40 Product Length mm $/lm
50
Flatdek Receiver Channel 1mm 6100 17.16
60

Roof Infill Strip – Flatdek

Product Length mm $/ea
Profile Foam Infill 260 4.49
(50mm H x 20mm W)

Foam Strip – Flatdek

Product Length mm $/ea
Foam Strip for receiver channel 2000 11.42
(50mm H x 20mm W)

Fasteners – Flatdek
Application Type Unpainted Painted Unpainted Painted
$/1000 $/1000 $/100 $/100
Steel up to SH1016 166.73 237.10 22.29 29.32
3.0mm BMT Metal Hex Head

Notes: 4 fasteners per m2 (Estimate for non-cyclonic area)

47 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Translucent Sheeting – Flatdek

Product Grams/m2 $/lm
Fibreglass 2400 68.95

Maximum length = 12200mm, Minimum length = 900mm

Notes:

Roofing
1. An extra charge will apply to lengths over 11000mm.
2. Available in Clear and Opal.
3. 32mm Weatherlok Washer required for all translucent sheeting.
4. Please refer to page 79 for other products in the Translucent Sheeting range.

Translucent Sheeting Accessories

Product Width (mm) Length $/roll $/1000
Roofing Wire 1800mm 50m 263.63 N/A
(2 x 300 x 150mm)
Lapseal 50mm x 6mm 11.7m 64.49 N/A
75mm x 6mm 11.7m 92.77 N/A
100mm x 6mm 11.7m 118.86 N/A
Weatherlok Washer 32mm (Dia) N/A 373.01
(Fibreglass only)

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 48
 New South Wales/ACT

Rooftrak
Description BMT Length (mm) $/ea
KIT 675 1.2 3018 566.71
KIT 675 1.2 6073 1058.29
KIT 675 Heavy Duty 2.0 3018 POA
KIT 675 Heavy Duty 2.0 6073 POA
675 L Connection Kit 62.55
Kit 675 shown above.
675 T Connection Kit 71.16
Roofing

675 X Connection Kit 71.16

224 mm 224 mm 675 Start/Finish End Plates Kit 53.02
65 mm

65 mm

675 Support Bracket 48.81

Male-male plank Male-female plank KIT 450 1.2 3018 362.91
KIT 450 1.2 6073 703.06
KIT 450 Heavy Duty 2.0 3018 POA
KIT 450 Heavy Duty 2.0 6073 POA
450 L Connection Kit 53.80
450 T Connection Kit 62.55
450 X Connection Kit 62.55
450 Start/Finish End Plates Kit 35.42
450 Support Bracket 36.39
Universal Support Plate POA

Notes:
1. Kits: Rooftrak is supplied in kits that include components and fixings.
2. Dimensions: The Rooftrak 450 system uses two planks (Total 450mm wide)
Rooftrak 675 uses three planks (Total 675mm wide)
3. Heavy Duty Rooftrak may be available on application.

NEED HELP?
Speak to an expert on 1800 641 417
For assistance with:
• Product Information • Spanning Advice
• Brochures & Manuals • Colour Samples
• Material Compatibility
Real People. Real Help.

49 Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08
 New South Wales/ACT

Components supplied in kits – Rooftrak

Description M/F M/M Support Screws Rivets L Heel/Toe
planks planks brackets (bag) (bag) bracket End plates
KIT 675
6 metre straight run 2 1 5 1 1
3 metre straight run 2 1 3 1 1
L Connection 1 1 3
T Connection 1 2 3

Roofing
X Connection 1 4
Start/Finish End Plate 6
675 Support Bracket 1
KIT 450
6 metre straight run 1 1 5 1 1
3 metre straight run 1 1 3 1 1
L Connection 1 1 2
T Connection 1 2 2
X Connection 1 4
Start/Finish End Plate 4
450 Support Bracket 1

Prices are subject to change without notice. Price excludes GST. Additional charges may apply. Effective 31/08/08 50