DRW170183AC

LCD Display Multi Panel Meter Measurement Input Zero Adjustment

Forces the display value of measured input to 0 (Zero).
Reset

MX4W SERIES
DC voltage DC current
● Zero adjustment range: -99 to 99 RUN mode
Measurement Input Display range Measurement Input Display range
Display Display ● Zero adjustment method:
input range impedance [STND] input range impedance [STND]
① Hold + keys for 3 sec at the same time.
INSTRUCTION MANUAL + + 5 sec
MODE
0.0-500.0V 50)0 0.0 to 500.0 0.000-5.000A %000 0.000 to 5.000
+ 3 sec
0-500V 500 0 to 500 0.00-5.00A %00 0.00 to 5.00 )15 )00
0.0-200.0V 0.0 to 200.0 0.000-2.000A @000
0.02Ω
0.000 to 2.000
INiT NO YES
20)0
4.062MΩ ②S  et display holding/zero adjustment [DI-T] of
0-200V 200 0 to 200 0.00-2.00A @00 0.00 to 2.00 MODE MODE

parameter 2 group as zero adjustment [ZERO].

0.00-50.00V 5)00 0.00 to 50.00 0.0-500.0mA 50)0 0.0 to 500.0 Short 3, 4 terminals and zero adjustment is
0.0-50.0V 5)0 0.0 to 50.0 0-500mA 500 0 to 500 INiT ※1
available.
0.00-20.00V 2)00 0.00 to 20.00 0.0-200.0mA 20)0 0.0 to 200.0 ※When zero adjustment is completed by ① or ② >>>>
0.87Ω
0.0-20.0V 2)0 0.0 to 20.0 0-200mA 200 0 to 200 method, the display part displays zero and the
50)0
0.000-5.000V %000 0.000 to 5.000 0.00-50.00mA 5)00 0.00 to 50.00 adjusted value is saved at [ZERO] of parameter
0.00-5.00V %00 0.00 to 5.00 0.0-50.0mA 5)0 0.0 to 50.0 1 group automatically.
Thank you for choosing our Autonics product. 1.000-5.000V 1-5A
162kΩ
1.000 to 5.000 0.00-20.00mA 2)00 0.00 to 20.00 ※If zero adjustment range is exceeded, the error
※1: F
 lashes twice sequentially and returns to
Please read the following safety considerations before use. 1.00-5.00V 1-5B 1.00 to 5.00 0.0-20.0mA 2)0 0.0 to 20.0 [OVER] flashes twice and it returns to RUN
RUN mode.
0.000-2.000V @000 0.000 to 2.000 4.00-20.00mA 4A20 4.00 to 20.00 mode, by maintaining previous setting value.
Safety Considerations 0.00-2.00V @00 0.00 to 2.00 4.0-20.0mA 4B20
21.87Ω
4.0 to 20.0 Parameter Group
※Please observe all safety considerations for safe and proper product operation to avoid hazards. 0.0-500.0mV 50)0 0.0 to 500.0 0.000-5.000mA %000 0.000 to 5.000
Parameter (0 to 2 group) setting
0-500mV 500 0 to 500 0.00-5.00mA %00 0.00 to 5.00
※ symbol represents caution due to special circumstances in which hazards may occur. 1. Each parameter and corresponding setting value will flash alternately every 0.5 sec.
0.0-200.0mV 20)0 0.0 to 200.0 0.000-2.000mA @000 0.000 to 2.000
4kΩ 2. Press the key to save the setting value and move to the next parameter.
Warning Failure to follow these instructions may result in serious injury or death. 0-200mV 200 0 to 200 0.00-2.00mA @00 0.00 to 2.00
3. If there is no key input for 60 sec, the unit will return to RUN mode.
0.00-50.00mV 5)00 0.00 to 50.00 -5.000-5.000A ,-%000 -5.000 to 5.000
Caution Failure to follow these instructions may result in personal injury or product damage. 4. Hold the key for 3 sec to return to RUN mode.
0.0-50.0mV 5)0 0.0 to 50.0 -5.00-5.00A ,-%00 0.02Ω -5.00 to 5.00 5. Press the , keys to change the set value.
-500.0-500.0V -500.0 to 500.0 -2.000-2.000A -2.000 to 2.000
Warning ,-50)0 ,-@000 ( : moves digits, : changes setting value)
-500-500V ,-500 -500 to 500 -2.00-2.00A ,-@00 -2.00 to 2.00 ※ Dotted parameters may not appear by model type or other parameter settings.
1. F ail-safe device must be installed when using the unit with machinery that may cause 4.062MΩ
-200.0-200.0V ,-20)0 -200.0 to 200.0 -500.0-500.0mA ,-50)0 -500.0 to 500.0 ※1. Refer to ' Measurement Input Type And Range'.
serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment,
ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster -200-200V ,-200 -200 to 200 -500-500mA ,-500 -500 to 500 Parameter 0 group
prevention devices, etc.) -50.00-50.00V ,-5)00 -50.00 to 50.00 -200.0-200.0mA ,-20)0 -200.0 to 200.0
0.87Ω
Failure to follow this instruction may result in fire, personal injury, or economic loss. -50.0-50.0V ,-5)0 -50.0 to 50.0 -200-200mA ,-200 -200 to 200 RUN mode
2. Install on a device panel to use. -20.00-20.00V ,-2)00 -20.00 to 20.00 -50.00-50.00mA ,-5)00 -50.00 to 50.00 MODE
Failure to follow this instruction may result in electric shock or fire. MODE

3. D o not connect, repair, or inspect the unit while connected to a power source. -20.0-20.0V ,-2)0 -20.0 to 20.0 -50.0-50.0mA ,-5)0 -50.0 to 50.0
162kΩ Does not appear when OUT1 preset output
Failure to follow this instruction may result in electric shock or fire. -5.000-5.000V ,-%000 -5.000 to 5.000 -20.00-20.00mA ,-2)00 -20.00 to 20.00 Max. value of operation mode [OU!T] of parameter 2 group is set
OUT1 high-limit OU!H
4. C heck 'Connections' before wiring. -5.00-5.00V ,-%00 -5.00 to 5.00 -20.0-20.0mA ,-2)0 -20.0 to 20.0 input range
※1
as OFF/LOW.
preset value
Failure to follow this instruction may result in fire. -2.000-2.000V ,-@000 -2.000 to 2.000 -5.000-5.000mA , -%000 -5.000 to 5.000
5. D o not disassemble or modify the unit. 21.87Ω
MODE
Setting range: -9999 to 9999
Failure to follow this instruction may result in electric shock or fire. -2.00-2.00V ,-@00 -2.00 to 2.00 -5.00-5.00mA ,-%00 -5.00 to 5.00 Does not appear when OUT1 preset output
-500.0-500.0mV ,-50)0 -500.0 to 500.0 -2.000-2.000mA ,-@000 -2.000 to 2.000 OUT1 low-limit Min. value of operation mode [OU!T] of parameter 2 group is set
Caution preset value
OU!L input range
※1
-500-500mV ,-500 -500 to 500 -2.00-2.00mA ,-@00 -2.00 to 2.00 as OFF/HIGH.
MODE
1. W
 hen connecting the power/measurement input, use 24(0.20mm ) to AWG 15(1.65mm ) cable 2 2 -200.0-200.0mV ,-20)0 -200.0 to 200.0 Setting range: -9999 to 9999
4kΩ
and tighten the terminal screw with a tightening torque of 0.78 to 0.98N.m. -200-200mV ,-200 -200 to 200 Does not appear when OUT2 preset output
Failure to follow this instruction may result in fire or malfunction due to contact failure. OUT2 high-limit Max. value of operation mode [OU@T] of parameter 2 group is set
-50.00-50.00mV ,-5)00 -50.00 to 50.00 OU@H input range
※1
2. U
 se the unit within the rated specifications. preset value as OFF/LOW.
-50.0-50.0mV ,-5)0 -50.0 to 50.0
Failure to follow this instruction may result in fire or product damage. MODE
Setting range: -9999 to 9999
3. U
 se dry cloth to clean the unit, and do not use water or organic solvent. AC voltage AC current
Failure to follow this instruction may result in electric shock or fire. Measurement Input Display range Measurement Input Display range Min. value of
Does not appear when OUT2 preset output
Display Display OUT2 low-limit
4. D
 o not use the unit in the place where flammable/explosive/corrosive gas, humidity, direct input range impedance [STND] input range impedance [STND] preset value
OU@L input range
※1 operation mode [OU@T] of parameter 2 group is set
sunlight, radiant heat, vibration, impact, or salinity may be present. 0.0-500.0V 50)0 0.0 to 500.0 0.000-5.000A %000 0.000 to 5.000 MODE
as OFF/HIGH.
Failure to follow this instruction may result in fire or explosion. Setting range: -9999 to 9999
5. K
 eep metal chip, dust, and wire residue from flowing into the unit. 0-500V 500 0 to 500 0.00-5.00A %00 0.00 to 5.00
0.02Ω
Failure to follow this instruction may result in fire or product damage. 0.0-200.0V 20)0 0.0 to 200.0 0.000-2.000A @000 0.000 to 2.000 Max. monitoring +
4.062MΩ hPEK reset )0
0-200V 200 0 to 200 0.00-2.00A @00 0.00 to 2.00 value
Do not appear when monitoring delay time [PEaK]
Model 0.0-110.0V 11)0 0.0 to 110.0 0.0-500.0mA 50)0 0.0 to 500.0
MODE
of parameter 2 group is set as 00 sec [00 S]. Hold
0-110V 110 0 to 110 0-500mA 500 0 to 500 the + for over 1 sec, to reset the parameter.
Model Measurement input Power supply Output Min. monitoring +
0.00-50.00V 5)00 0.00 to 50.00 0.0-200.0mA 20)0 0.0 to 200.0 lPEK )0
MX4W-V-FN Indicator 0.87Ω value reset
0.0-50.0V 5)0 0.0 to 50.0 0-200mA 200 0 to 200
MX4W-V-F1 DC/AC voltage NPN open collector output MODE

0.00-20.00V 2)00 0.00 to 20.00 0.00-50.00mA 5)00 0.00 to 50.00

MX4W-V-F2 24-240VAC 50/60Hz, PNP open collector output
0.0-20.0V 2)0 0.0 to 20.0 0.0-50.0mA 5)0 0.0 to 50.0 Parameter 1 group
MX4W-A-FN 24-240VDC Indicator 162kΩ
0.000-5.000V %000 0.000 to 5.000 0.00-20.00mA 2)00 0.00 to 20.00
MX4W-A-F1 DC/AC current NPN open collector output RUN mode
0.00-5.00V %00 0.00 to 5.00 0.0-20.0mA 2)0 0.0 to 20.0
MX4W-A-F2 PNP open collector output MODE

0.000-2.000V @000 0.000 to 2.000 0.000-5.000mA %000 0.000 to 5.000 3 sec

MODE 2 sec
21.87Ω
0.00-2.00V @00 0.00 to 2.00 0.00-5.00mA %00 0.00 to 5.00
Unit Description 1. Measurement value display part 0.0-500.0mV 50)0 0.0 to 500.0 0.000-2.000mA @000 0.000 to 2.000 PA1
5 6 7 8 2. key MODE
0-500mV 500 0 to 500 0.00-2.00mA @00 0.00 to 2.00
: Press the key to enter parameter groups, return RUN 0.0-200.0mV 20)0 0.0 to 200.0 Input type
mode, move parameters, or save the setting values. 4kΩ
2 3. key
0-200mV 200 0 to 200 DCAC DC ,-DC AC
: Press the key to move digits, enter parameters, or 0.00-50.00mV 5)00 0.00 to 50.00 MODE

1 3 move parameter setting values. 0.0-50.0mV 5)0 0.0 to 50.0

Input range
4. key ※Display range of [SCAL] will vary depending on the decimal point. Max. value of
IN-R ※1 Input range varies depending on model, input type [DCAC].
4 : Press the key to change digit value, enter or change (-9999 to 9999, -999.9 to 999.9, -99.99 to 99.99, -9.999 to 9.999) input range
parameters, or chage the parameter setting value. ※When changing measurement input type, OU .H/OU .L/H.PEK/L.PEK/DISP/IN-T/DOT/H-SC/L-SC/ MODE

5. C
 ontrol output (OUT1/OUT2) indicator (red, indicator model: white) SPAN/ZERO/eSPN/H-RG/L-RG/D.UNT/OU .T/HYs parameters are reset.
6. MAX/MIN indicator (green, indicator model: white) ※Frequency measurement range (AC voltage/current): 0.100 to 1200Hz Standard Scale Frequency Power factor
※Check the unit indicator when selecting measurement input type. Display
: When input is over/below the range, HHHH or LLLL appears.
7. AC/DC indicator (green, indicator model: white)
※Parameter setting order of input range [IN-R] is followed by the above table. DISP STND SCAL FREQ PF
E.g.) AC current: %000 → %00 → @000 → … → @000 → @00 AC voltage/current DC voltage/current
8. Unit (V/mV/A/mA/Hz/%) indicator (yellow, indicator model: white) ※When "HHHH" or "LLLL" is flashes with a certain measurement input, disconnect power supply and
MODE

then check the cables.

Dimensions (unit: mm) ※Connect to the input terminals whose 30% to 100% of the input range includs the max. value of the AC measurement
input range to measure. When the max. input value is under the 30% of the input terminal range,
91.5 ● Panel cut-out display accuracy is degraded. When the max. input value is over the 100%, it may result in input IN-T AVG RMS ※Only appears in input type is set as [AC].
Min. 116 terminal damage. MODE

Preset Output Operation Mode [PA 2 group: OU!T/OU@T] Standard

[STND] at
Scale [SCAL] at
display [DISP]
Frequency [FREQ] at display
[DISP] (AC voltage/current)
Power factor [PF] at display
[DISP] (DC voltage/current)
45+0.6

Operation display
0

96 4 20 Output operation Description

mode [DISP] High-limit
Min. 52

Decimal point location Decimal point location input value

92+0.8 Max. value of
0
DOT Setting range:
DOT Setting range: H-RG input range
※1
OFF No output 0, )0, )00, )000 0, )0, )00, )000
44.4
48

OUT1 output No output MODE MODE MODE

High-limit scale value

OUT1.H Hysteresis Max. value of
ON period: Display value ≥ OU!H H-SC Mantissa of gradient Low-limit
● Bracket HIGH (HYS) input range
※1
OFF period: Display value ≤ OU!H- HYs1 correction for frequency input value
OUT1 output
MODE
Min. value of
● Terminal cover 4.9 SPAN !000 L-RG ※1
input range
36 3 MODE Setting range: MODE
Low-limit scale value
Hysteresis ON period: Display value ≤ OU!L 0.100 to 9.999
15.5

LOW OUT1.L Min. value of

(HYS) OFF period: Display value ≥ OU!L+ HYs1 L-SC ※1 (times)
22

OUT1 output input range

93.7 15.9 MODE

Index of gradient
ON period: Display value ≤ OU!L, Span correction of correction for frequency
OUT1.H
Connections and Insulated Block Diagram HL OUT1.L
Hysteresis
(HYS)
Display value ≥ OU!H high limit value
Setting range: eSPN 10-0
※Use terminals of size specified below. OFF period: Display value ≥ OU!L+ HYs1, SPAN !000
OUT1 output 0.100 to 9.999 Setting range:
Display value ≤ OU!H- HYs1 MODE
a b MODE (times) 10-0,10-1,
ON period: Display value ≥ OU!L, Deviation correction of
10-2,10 1
a b Min. Max. OUT1.H Hysteresis Display value ≤ OU!H low limit value
3.0mm 6.0mm HL-G OUT1.L (HYS) Setting range:
<Forked> OFF period: Display value ≤ OU!H- HYs1,
OUT1 output ZERO 00 -99 to 99
Display value ≥ OU!H+ HYs1
MX4W-V-F MX4W-A-F MODE

※Set preset output mode separately for each OUT1/OUT2.

※4 ※4
※OUT1/OUT2 are operated individually depending on the set preset output operation mode. Unit
※1 ※5
※8 SOURCE ※8 SOURCE ※High/low preset value parameters of the parameter 0 group appear by setting preset output dUNT Setting range: MV, V, MA, A, HZ, OFF
※2 24-240 ※6 24-240
Hold/Zero VAC/VDC Hold/Zero VAC/VDC
operation mode.
※3 ※7 MODE
※When changing preset output operation mode, OU .H/ OU .L/HYs are reset.
※1: DC±500mV/±200mV/±50mV, ※5: DC±20mA/4-20mA/±5mA/±2mA, Parameter 2 group
AC0-500mV/0-200mV/0-50mV
※2: DC±20V/±5V/1-5V/±2V,
AC0-20mA/0-5mA/0-2mA
※6: DC±500mA/±200mA/±50mA, Factory Defaults RUN mode
AC0-20V/0-5V/0-2V AC0-500mA/0-200mA/0-50mA MX4W-V MX4W-V MX4W-V MX4W-A MX4W-A MX4W-A MODE 3 sec
Group Parameter
※3: DC±500V/±200V/±50V, ※7: DC±5A/±2A, AC0-5A/0-2A (DC) (±DC) (AC) (DC) (±DC) (AC) MODE 4 sec
AC0-500V/0-200V/0-110V/0-50V ※8: Indicator model does not have the hold/zero OU!H ※1
50)0 50)0 50)0 %000 %000 %000
※4: F or using DC power, connect wires regardless terminal. OU!L※1 00)0 ,-50)0 00)0 )000 ,-%000 )000 PA2
of polarity. PA0
OU@H※1 50)0 50)0 50)0 %000 %000 %000
NPN open collector output PNP open collector output Option output ADC input circuit
Power (PA 0 ※1
OUT1 preset ※Do not appear at indicator models.
OU@L 00)0 ,-50)0 00)0 )000 ,-%000 )000
and hold/zero and display part group) output operation OU!T OFF
hPEK )0 )0 )0 )0 )0 )0
1 2 3 4 5 6 7 8 9 10 mode MODE
lPEK )0 )0 )0 )0 )0 )0 Setting range: OFF, HIGH, LOW, HL, HL-G
OUT1 OUT2 Hold/Zero OUT1 OUT2 Hold/Zero ※Input and output are insulated from the power. DCAC DC -DC AC DC ,-DC AC OUT2 preset
IN-R 50)0 ,-50)0 50)0 %000 ,-%000 %000 output operation OU@T OFF
Specifications DISP STND STND STND STND STND STND mode MODE

Model MX4W-V-F MX4W-A-F

IN-T - - AVG - - AVG
Measurement input DC/AC voltage DC/AC current
DOT 00)0 00)0 00)0 )000 )000 )000 OUT1 preset
PA1 H-SC
HYs1 0)1 Does not appear when preset output operation mode
DC input: a pprox. -110 to 110% of each measurement input range 50)0 50)0 50)0 %000 %000 %000 hysteresis
Max. allowable input (when not using minus input: -10 to 110%) (PA 1 L-SC 00)0 ,-50)0 00)0 )000 ,-%000 )000 MODE
[OU!T, OU@T] is set as OFF.
AC input: approx. 110% of each measurement input range group) SPAN !000 !000 !000 !000 !000 !000 OUT2 preset Setting range: within 10% of max. display range of input
Power supply 24-240VAC 50/60Hz, 24-240VDC ZERO 00 00 00 00 00 00 hysteresis
HYs2 0)1 (if display range is over 10000, it is fixed as 999)
Allowable voltage range 90 to 110% of the rated voltage eSPN - - 10-0 - - 10-0 MODE

Power supply Max. 5VA (24-240VAC 50/60Hz), Max. 3W (24-240VDC ) H-RG 50)0 50)0 - %000 %000 - Startup
Display method
※1 12-segment (measurement value display part: white, character height: 19mm), L-RG 00)0 ,-50)0 - )000 ,-%000 - compensation STaT 0)0 Setting range: 00.0 to 99.9 sec
other display parts (red, green, yellow, indicator model: white) LCD method dUNT V V V A A A time MODE

23℃±5℃ - D  C input: ±0.1% F.S. ±2-digit, AC input: ±0.3% F.S. ±3-digit OU!T※1 OFF OFF OFF OFF OFF OFF Monitoring
Display accuracy
※The terminal for 5A of current input, ±0.3% F.S. ±3-digit OU@T※1 OFF OFF OFF OFF OFF OFF delay time PEaK 00 S Setting range: 00 to 30 sec
0℃ to 50℃ - DC/AC input: ±0.5% F.S. ±3-digit HYs1※1, ※2 0)1 0)1 0)1 )001 )001 )001 MODE
※The terminal for 5A of current input, ±1% F.S. ±3-digit
PA2 HYs2※1, ※2 0)1 0)1 0)1 )001 )001 )001
Display cycle 0.2 to 5.0 sec (select per 0.1 sec) Display period DIsT )2 5 Setting range: 0.2 to 5.0 sec
(PA 2 STaT 0)0 0)0 0)0 0)0 0)0 0)0
A/D conversion method Sigma-Delta ( - ) analog-to-digital converter
group) PEaK 00 S 00 S 00 S 00 S 00 S 00 S MODE
Sampling cycle DC input: 50ms (resolution 1/20,000), AC input: 16.6ms (resolution 1/20,000)
DIsT Set display holding or zero adjustment by shorting 3, 4
)2 S )2 S )2 S )2 S )2 S )2 S Display value
Max. display range -9999 to 9999 (4-digit)
DI-T HOLD HOLD HOLD HOLD HOLD HOLD holding/ DI-T HOLD terminals.
NPN/PNP open collector output Setting range: HOLD (display holding), ZERO (zero adjustment)
※2 LOC OFF OFF OFF OFF OFF OFF Zero adjustment MODE
Preset output Load voltage: max. 30VDC Load current: max. 100mA ※Does not appear at indicator models.
Residual voltage: max. 1VDC (NPN), max. 2VDC (PNP) ※1: Does not appear in indicator models.
※3 ※2: It will vary depending on input range [IN-R] setting. Setting range:
AC measurement Select RMS value/AVG value measurement methods
※3 Lock LOC OFF OFF Unlock Lock parameter
Frequency measurement Measurement range: 0.100 to 1200Hz (varies depending on the decimal point)
Insulation resistance Over 100MΩ (at 500VDC megger) Cautions during Use MODE
LOC2
1, 2 groups
Dielectric strength 3,000VAC 50/60Hz for 1 min (between all terminals and case) 1. Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected accidents. Lock parameter Lock parameter
LOC1 LOC3
2. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting 1 group 0, 1, 2 groups
Noise immunity ±2kV the square wave noise (pulse width: 1㎲) by the noise simulator
Mechanical 0.75mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 2 hours the power.
Vibration
Malfunction 0.5mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 10 min 3. Keep away from high voltage lines or power lines to prevent inductive noise.
In case installing power line and input signal line closely, use line filter or varistor at power line and
Major Products
Mechanical 100m/s2 (approx. 10G) in each X, Y, Z direction for 3 times Photoelectric Sensors Temperature Controllers
Shock shielded wire at input signal line.
Malfunction 300m/s2 (approx. 30G) in each X, Y, Z direction for 3 times Fiber Optic Sensors Temperature/Humidity Transducers
Do not use near the equipment which generates strong magnetic force or high frequency noise. Door Sensors SSRs/Power Controllers
Environ- Ambient temp. -10 to 50℃, storage: -20 to 60℃
ment Connection with the line filter Connection with the varistor Door Side Sensors Counters
Ambient humi. 35 to 85%RH, storage: 35 to 85%RH
Area Sensors Timers
Double insulation or reinforced insulation (mark: , dielectric strength between the Install the line filter close Proximity Sensors Panel Meters
Insulation type
measurement input part and the power part: 1kV) to the panel meter
HI Pressure Sensors Tachometers/Pulse (Rate) Meters
Approval HI 110/ Rotary Encoders Display Units
※4 110/ Panel meter Connector/Sockets Sensor Controllers
Weight Approx. 100g (approx. 77g) Panel meter 220VAC http://www.autonics.com
220VAC LOW Switching Mode Power Supplies
※1: When using the unit at low temperature (below 0℃), display cycle is slow due to characteristics of LCD. LOW Control Switches/Lamps/Buzzers HEADQUARTERS:
Control output operates normally. I/O Terminal Blocks & Cables 18, Bansong-ro 513beon-gil, Haeundae-gu, Busan,
※2: Indicator model (MX4W- -FN) does not have the function. Stepper Motors/Drivers/Motion Controllers
※3: AC, frequency measurement are available when input type is AC. Earth ground South Korea, 48002
Graphic/Logic Panels TEL: 82-51-519-3232
※4: The weight includes packaging. The weight in parenthesis is for unit only.
4. This unit may be used in the following environments. Field Network Devices E-mail: sales@autonics.com
※Environment resistance is rated at no freezing or condensation.
※The above specifications are subject to change and some models may be discontinued without notice. ①Indoors (in the environment condition rated in 'Specifications') ②Altitude max. 2,000m Laser Marking System (Fiber, Co₂, Nd:YAG)
Laser Welding/Cutting System DRW170183AC
※Be sure to follow cautions written in the instruction manual and the technical descriptions (catalog, homepage). ③Pollution degree 2 ④Installation category II