工业缝纫机安全使用注意事项：

1.必须遵守基本措施；

2.必须经过专业培训，对缝纫机设备性能、

3.使用前应检查所有安全装置；

4.在安装机针、更换机针、压脚、针板、送布牙、弯针、旋梭或修理时，应立即关闭电源；

5.离开缝纫机或工作场所时应关闭电源；

6.使用离合马达时，要等待马达完全停止后再进行；

7.缝纫机及附属装置使用的机油，润滑油等液体流入眼睛或沾到皮肤上应立即清洗；

8.禁止用手触摸缝纫机通电时的零件或装置；

9.有关工业用平缝机与包缝机的修理、改造、主要机构的调整由专门技术人员来进行；

10.一般的维修保养由专人进行；

11.在电气方面的修理应在电气技术员的监督和指导下进行；

12.缝纫机使用期间应定期清扫；

13.为了正常安全运转，应安装地线，同时应在不受高频焊接机等强噪声源影响的环境下使用；

14.电源插头应由专人安装；

15.工业用平缝机、包缝机在指定用途以外不能使用。

环保要求：
1、使用过程中产生的废油及其他废弃物请根据当地环保的要求进行合理的处置。

2、请在使用完后及时关闭电源，减少电能的消耗。

3、请在说明书要求的电压及环境下使用，已延长产品的使用寿命，减少废弃物的产生。

4、机器报废后请勿将本机器及其附件作为普通的生活垃圾处理。请遵守本设备及其附件处

理的本地法令，并支持回收行动。
Notes for safe use of industrial sewing machines：
1. Basic measures must be observed.

2. Pass the specialized training and master sewing machine equipment performance.
3. All safety devices should be checked before use.

4. When installing needle, and changing needle, presser foot, plate, feed dog , bent

needle, hook or repairing, the power supply should be turned off immediately.
5. Power should be turned off when leaving the sewing machine or workplace.

6. When using the clutch motor, please wait until the motor stops completely.

7. The machine oil and other liquids used in sewing machines and ancillary devices
should be cleaned immediately when they are put into eyes or touch skin.

8. Do not touch the parts or devices when the machine is powered by hand.

9. The repair, renovation and adjustment of the main mechanisms of the relevant
industrial sewing machines and overseers shall be carried out by specialized technicians.

10. General maintenance is carried out by specially-assigned persons.

11. Electrical repairs should be performed under the supervision and direction of the
electrical technician.

12. The machine should be cleaned regularly during operation.

13. In order to operate normally and safely, ground lines should be installed, and they
should be used in an environment free from strong noise sources such as high

frequency welding machine.

14. Power plug should be installed by specially-assigned person.

15. Industrial lockstitch sewing machine and overlock sewing machine can not be used

except the designated use.

Environmental requirements：
Please dispose the waste oil and other waste products properly according to local

environmental protection requirements.

Please turn off the power after use to reduce power consumption.

Please use under the voltage and environment required in the manual to extend the

service life of the product and reduce waste generation.

4、Do not treat the machine and its accessories as ordinary household garbage after

being scrapped. Please comply with local laws governing the disposal of the equipment

and its accessories and support recycling operations.

 使用说明书/Manual book
目录 Contents ………………………………………………………………………………………………… 页 Page
1 安全 Safety ……………………………………………………………………………………………………………… 2
2 特点及用途 Special features and applications …………………………………………………………3
3 技术参数 Specifications ………………………………………………………………………………………… 4
4 控制器 Controls ……………………………………………………………………………………………………… 4
4.01 控制开关 Controls On/off switch ……………………………………………………………………………… 4
4.02 机头开关 Keys on the machine head ……………………………………………………………………… 5
4.03 脚踏板 Pedal …………………………………………………………………………………………………………5
4.04 手动抬压脚 Lever for lifting roller presser ……………………………………………………………… 6
4.05 膝控杠杆 Knee lever …………………………………………………………………………………………… 6
4.06 针距调节按钮 Key for setting stitch length ………………………………………………………………7
4.07 轮前转向 Swing out roller presser ………………………………………………………………………… 7
5 安装 ………………………………………………………………………………………………………………………8
5.01 调整台板高度 Adjusting the table-top height ……………………………………………………… 8
5.02 安装线架 Fitting the reel stand …………………………………………………………………………9
6 调试 Commissioning ………………………………………………………………………………………… 9
6.01 安装机针 Inserting the needle …………………………………………………………………………10
6.02 绕底线、调节缝线张力 Winding the bobbin thread, adjusting the thread tension …… 11
6.03 拆卸/安装梭壳 Removing/Inserting the bobbin case ………………………………………………12
6.04 梭壳穿线/调整梭线张力
Threading the bobbin case/Adjusting the bobbin thread tension …………………………13
6.05 单针穿线及调节张力
Threading the needle thread and regulating its tension (Single Needle) ………………14
6.06 双针穿线及调节张力
Threading the needle thread and regulating its tension (Double Needle) ………………16
6.07 针距的调节 Setting the stitch length … …………………………………………………………………17
7 维护和保养 Care and maintenance ……………………………………………………………………… 18
7.01 维修和维护周期 Servicing and maintenance intervals ……………………………………………18
7.02 清理 Cleaning ……………………………………………………………………………………………………18
7.03 锁头槽的润滑 Oiling the hook ……………………………………………………………………………19
7.04 梭头的润滑注油 Oil bowl for hook lubrication ………………………………………………………20
7.05 传动齿轮的润滑 Lubricating the bevel gears …………………………………………………………20
1 安全 Safety
• 机器应该由受过专业训练或具有足够操作经验者在完全阅读和理解本说明书后操作。
• This machine may only be operated by adequately trained operators and
only after having completely read and understood the Instruction Manual!

• 机器不能在没有安全装置下操作，必须遵循有关操作的所有安全规定。
• This machine may only be used for the purpose for which it is intended and
may not be operated without its safety devices. All safety regulations relevant
to its operation are to be adhered to.

• 当换缝纫零件（如机针、轮钱、针板和梭仔）、穿线、离开机器后无人操作或者在维
修保养时，应该关掉转换开关或拔掉电源插头。
• When exchanging sewing tools (e.g. needle, roller presser, needle plate and
bobbin), when threading the machine, when leaving the machine unattended
and during maintenance work, the machine is to be separated from the
power supply by switching off the On/Off switch or by removing the plug
from the mains!

• 日常维护工作应由受过训练的人员进行。
• Everyday maintenance work is only to be carried out by appropriately trained
personnel!

• 维修和特殊的维护工作只能由合格的服务人员或受过专业训练的人员进行。
• Repairs and special maintenance work may only be carried out by qualified
service staff or appropriately trained personnel!

• 电器设备操作只能由受过相关训练的人员操作。
• Work on electrical equipment may only be carried out by appropriately
trained personnel!

• 不允许在带有电压的零件和装置上工作。
• Work is not permitted on parts and equipment which are connected to the
power supply.

2
• 必须在遵守所有相关的安全规定的前提下才能修改和变更机器。
• Modifications and alterations to the machine may only be carried out under
observance of all the relevant safety regulations!

• 在维修工作中只允许使用我们批准使用的备件，需要明确指出的是，所有不是由我
们供货的备件和附件都未经我们检查，也没有被我们批准使用。装入和/或使用这样
的产品可能会对机器的设计特性造成负面影响，对由于使用非原装零件造成的损失，
我们不承担任何责任。
• Only spare parts which have been approved by us are to be used for repairs!
We expressly point out that any replacement parts or accessories which are
not supplied by us have not been tested and approved by us. The installation
and/or use of any such products can lead to negative changes in the
structural characteristics of the machine. We are not liable for any damage
which may be caused by non-original parts.

2 特点及用途 Special features and applications

单/双针高速罗拉车（自动剪线、自动回缝、自动抬压脚）用于制鞋业，特别适用于缝
制高档皮鞋、包袋、手套、帽子等弧形中厚料物品。
Single/Double Needle Post-bed Sewing Machine (Thread Trimming、Backstitch
Sewing、Presser Foot) is used for shoe manufacturing, It is especially available
for sewing on medium heavy weight articles with arc-shaped, such as superior
leather shoes, hand bags, gloves, caps etc, it ensures you easy daily
maintenance.
任何没有被制造商确认的机器使用都是不合理的，制造商不承担任何使用不
当造成的机器损坏。合理的使用机器应遵循制造商确认的所有操作，包括调
试、维护和维修措施。
Any and all uses of this machine which have not been approved of by
the manufacturer are considered to be inappropriate! The
manufacturer cannot be held liable for any damage caused by the
inappropriate use of the machine! The appropriate use of the
machine includes the observance of all operational, adjustment,
maintenance and repair measures required by the manufacturer!

3
3 技术参数 Specifications
机针类型 Stitch type: …………………………………………………………… DP5X16 (#11-#20)
最大缝目 Max stitch length 7 mm/单针 Single Needle 5mm/双针 Double Needle
最高缝纫速度 S.P.M……………………………………………………………………………2000 r/min
噪音 Noise data………………………………………………………………………… 73db (±2.5db)
净重 N.W .………………………………………………………………………………………………… 70KG
毛重 G.W .………………………………………………………………………………………………… 76KG

机头尺寸 Sewing head dimensions:

总长 Length………………………………………………………………………………………… 615 mm
总宽 Width ………………………………………………………………………………………… 180 mm
高度（台板以上）Height (above table) ……………………………………………… 500 mm
台板尺寸 Bedplate dimensions…………………………………………………… 518 x 178 mm

4 控制器 Controls
4.01 控制开关 Controls On/off switch

• 通过 1 键来接通或关闭电源。

•Through the key 1 to switch on or off the

power

4
4.02 机头开关 Keys on the machine head

• 机器工作时，按下按钮 1，机器倒针。
• 按钮 2 用于经行参数设置

•As long as key 1 is pressed during sewing,

the machine sews in reverse.
• Keys 2 can be used for parameter
settings

4.03 脚踏板 Pedal

0 = 中间位（机器不工作）
+1 = 机器处于缝制状态
-1 = 抬压脚
-2 = 剪线，单段缝制结束

0 = Neutral position
+1 = Sewing
-1 = Raise roller presser
-2 = Trim sewing threads

5
4.04 手动抬压脚 Lever for lifting roller presser

• 通过压棒提杆 1 可抬起轮前组件。

•The roller presser can be raised by

turning lever 1.

4.05 膝控杠杆 Knee lever

• 按箭头所示方向移动膝控杠杆 1 可抬起轮前
组件。

• The roller presser can be raised by

pres­sing the knee lever 1 in the
direction of the arrow.

6
4.06 针距调节按钮 Key for setting stitch length

• 按下按钮 1 不放，转动皮带轮可调节针距。

• The stitch length is set by pressing key 1

and turning the balance wheel.

4.07 轮前转向 Swing out roller presser

• 当轮前抬起时，可以推动轮前使之旋转。.

• When the roller presser is raised, it can

be swung out by pulling it lightly
down­wards.

7
5 安装 Installation

为了运输方便，包装时要求尽可能的降低台板。以下描述如何调整台板高度。
The method of packaging used requires that the table top be lowered
for transport. The following is a description of how to adjust the
height of the table top.

5.01 调整台板高度 Adjusting the table-top height

• 松开螺丝 1 和螺丝 2.按需要调整台板高度。

• 锁紧螺丝 1。
• 调整脚踏板至您可以舒适工作的位置，然后锁紧螺丝 2。
• Loosen screws 1 and 2 and set the desired table-top height
• Tighten screws 1 well.
• Adjust the position of the pedal so that you can operate it comfortably and
tighten screw 2.

8
5.02 安装线架 Fitting the reel stand

• 如图所示安装线架。
• Fit the reel stand as shown.

6 调试 Commissioning
本说明书中的所有指令和条例必须遵循，特别要注意安全说明。
All instructions and regulations in this instruction manual must be
observed. Special attention must be paid to all safety regulations!

所有安装工作必须由受过相关培训的人员经行。安装时关掉开关，脱离电压，
或拔掉电源插座上的插头。
All setting-up work must only be carried out by personnel with the
appropriate training. For all setting-up work the machine must be
disconnected from its power supply by turning off the on/off switch,
or removing the plug from the electric power socket.

9
6.01 安装机针 Inserting the needle

关掉机器，机器的意外启动可能会对您造成受伤的危险。
Switch off the machine!
Danger of injury due to unintentional starting of the machine!

• 提升压脚 1 且向外旋转。
• 松掉螺丝 2，将针插入最深处。长沟槽必须面向左（单针）。
• 松掉螺丝 2，将针插入最深处，左针的长沟槽向右，右针的长沟槽向左（双针）。
• 锁紧螺丝 2，压脚转向至原位。
• Raise the roller presser 1 and swing it out.
• Loosen screw 2 and insert the needle as far as possible. The long groove
must face to the left （Single Needle） .
• Loosen screws 2 and insert the needles as far as possible. the long groove of
the left needle is facing right, and that of the right needle is facing left
（Double Needle）.
• Tighten screws 2 and swing roller presser 1 back into position.

10
6.02 绕底线，调节缝线张力 Winding the bobbin thread, adjusting the thread
tension

• 安装空梭子 1 至梭子轴 2 上。
• 按图穿线且逆时针旋转梭子几圈。
• 按下梭子轴 2 和顶杆 3 接通打线器。
• Place an empty bobbin 1 onto bobbin shaft 2.
• Thread the bobbin in accordance with the pictures and wind it
anti-clockwise around bobbin 1 a few times.
• Switch on the bobbin winder while at the same time pressing bobbin winder
spindle 2 and lever 3.

机器运转时梭子会自动绕满。
The bobbin fills up during sewing.

• 梭子 1 上线的张力可以通过滚花螺丝 4 调节。
• 梭子上的线绕满时会自动停止绕线。
• 拿下绕满线的梭子 1，通过切刀 5 剪线。

11
• The tension of the thread on bobbin 1 can be adjusted with knurled screw 4.
• The bobbin winder stops automatically when bobbin 1 is full.
• Remove the filled bobbin 1 and cut the thread on knife 5.

如果绕线不均匀，松掉螺丝 6 根据需要旋转绕线柄 7，调整好后锁紧螺丝 6。

If the thread is wound unevenly, loosen nut 6 and turn thread guide 7
accordingly. Retighten nut 6 after the adjustment.

6.03 拆卸/安装梭壳 Removing/Inserting the bobbin case

关掉机器，机器的意外启动可能会对
您造成伤害。
Switch the machine off! Danger
of injury if the machine is started
accidentally!
拆卸梭壳：
• 打开大斧盖
• 拔起闭锁 1 取出梭壳 2.
Removing the bobbin case:
• Open the post cap.
• Raise latch 1 and remove bobbin case 2.

安装梭壳：
• 放入梭壳 2.
• 按下闭锁，关上大斧盖。
Inserting the bobbin case:
• Insert bobbin case 2.
• Close the latch and close the post cap.

12
6.04 梭壳穿线/调整梭线张力
Threading the bobbin case/Adjusting the bobbin thread tension

• 装入梭子至梭壳 1 内。
• 线穿过弹板 2 下面的槽内。
• 线穿过凹口。
• 通过旋转螺丝 3 调整线的张力。
• Insert the bobbin into the bobbin
case 1.
• Pass the thread through the slot under
spring 2.
• Pass the thread through the notch.
• Adjust the thread tension by turning
screw 3.

13
6.05 单针穿线及调节张力
Threading the needle thread and regulating its tension ( single needle)

关掉机器，机器的意外启动可能会对您造成伤害。
Switch the machine off!
Danger of injury if the machine is started accidentally!

14
• 如图所示穿线
• 穿线方向为从左到右。
• 通过滚花螺丝 1 可以调节线的张力。
• Thread the needle thread as shown.
• The needle is threaded from the left to the right.
• Adjust the needle thread tension by turning milled screw 1.

15
6.06 双针穿线及调节张力
Threading the needle thread and regulating its tension( double
needle)

关掉机器，机器的意外启动可能会对您造成受伤的危险。
Switch the machine off!

16
 Danger of injury if the machine is started accidentally!
• 双针穿线方法如图所示
• 左针穿线方向为从右到左，右针的穿线方向为从左到右。
• 通过滚花螺丝 1 可以调节线的张力。
• Thread both needle threads as shown.
• The left needle is threaded from the right to the left, and the right needle
from the left to the right.
• Adjust the needle thread tensions by turning milled screws 1.

6.07 针距的调节 Setting the stitch length

• 按住按钮 1 不放，旋转皮带轮直到针锁锁入凹槽位置。
• 按住按钮 1，来回转动皮带轮直到所需针距。
• Press key 1 and at the same time turn the balance wheel until the stitch
setter clicks into position.
• Hold down key 1 and turn the balance wheel to and fro until the stitch length
required is shown on the scale 2 opposite the bottom edge 3 of the belt
guard recess.

17
7 维护和保养 Care and maintenance
7.01 维修和维护周期 Servicing and maintenance intervals
清理……………………………………………………………………………每天，连续操作时更频繁
检查油位（面线润滑/锁头润滑）……………………………………………………每天使用之前
锁头槽的注油 ………………………………………………………………………………每天使用之前
传动齿轮的润滑 …………………………………………………………………………………一年一次
Clean………………………………… daily, more frequently if in continuous operation
Oil level (thread lubrication/hook lubrication) …………………… daily, before use
Oil the hook ……………………………………………………………………… daily, before use
Lubricate the bevel gears ……………………………………………………………once a year

7.02 清理 Cleaning
在机器连续使用时，每天都需对梭头、内斧、平面送料齿轮经行清理几次。
Clean the hook, hook compartment and toothed wheel 3 daily, several times if
in continuous use.
关掉机器，机器的意外启动可能
会对您造成受伤的危险
Switch the machine off!
Danger of injury if the
machine is started
accidentally!
• 将针棒移至最高点。
• 打开大斧盖，取下梭壳盖和梭子。
• 选松压板 1.
• 旋转手轮知道梭壳尖点进入梭头槽内
约 5mm.
• 取下梭壳 2.
• 用石蜡清理梭壳。
• 放入梭壳时要确保梭子能顺利装入。
• 梭壳凸起插入针板槽内。
• 锁紧压板 1.关上大斧盖。

18
• Bring the needle bar to its highest position.
• Open the post cap and remove the bobbin case cap and the bobbin.
• Unscrew hook gib 1.
• Turn the handwheel until the point of bobbin case 2 penetrates into the
groove of the hook race approx. 5 mm.
• Remove bobbin case 2.
• Clean the hook race with paraffin.
• When inserting the bobbin case 2, ensure that the horn of the bobbin.
• case 2 engages in the groove of the needle plate.
• Screw hook gib 1 back on and close the post cap.

7.03 锁头槽的润滑 Oiling the hook

关掉机器，机器的意外启动可能会
对您造成伤害的危险。
Switch the machine off!
Danger of injury if the
machine is started
accidentally!

• 在机器调试前或机器长期未操作的情况
下，需要将勾线器（见箭头）注滴几滴润
滑油。
• Before commissioning the machine,
and after long periods out of
operation, pour a few drops of oil into
the hook race (see arrow).

19
7.04 梭头的润滑注油 Oil bowl for hook lubrication

使用之前必须检查油位。必须经
向油盒 1 内加油。
• 如果需要可以从注油孔加油
Check the oil level before each
use.
There must always be oil in
reservoir 1.
• If required refill oil through hole.

7.05 传动齿轮的润滑 Lubricating the bevel gears

关掉机器，机器意外启动可能对您造成受伤的危险。
Switch the machine off!
Danger of injury if the machine is started accidentally!

• 所有的传动齿轮必须每年提供一次新的油脂。
• 倾斜机器可方便操作。
• All bevel gears must be supplied with new grease once a year.
• Tilt the sewing head back onto the support.

20
零件手册
PARTS BOOK
 零件样本/Parts book
1. 本体机构

ARM BED AND IT'S ACCESSORIES ................................................................................................................... 01

2. 压棒机构

PRESSER FOOT BAR MECHANISM ...................................................................................................................05

3. 天平及针棒摇动台机构

TAKE-UP LEVER & NEEDLE BAR ROCKING MECHANISM .......................................................................... 07

4. 缝线压力调整机构

UPPER THREAD TENSION REGULATION MECHANISM .............................................................................. 11

5. 主轴传动机构

UPPER & MAIN SHAFT TRANSMISSION MECHANISM............................................................................... 13

6.1 下送料、剪线机构 JK-6691、JK-6692

LOWER FEED & THREAD TRIMMING MECHANISM .................................................................................... 15

6.2 下送料、剪线机构 JK-6691-X、JK-6681

LOWER FEED & THREAD TRIMMING MECHANISM .................................................................................... 17

7.1 轮前、上边心机构（被动送料）

ROLLER PRESSER FOOT & UPPER SIDE SHAFT MECHANISM .................................................................. 19

7.2 轮前、上边心机构（-1 型选配）

（主动送料）

ROLLER PRESSER FOOT & UPPER SIDE SHAFT MECHANISM .................................................................. 21

8.1 右边座机构 JK-6691、JK-6692

RIGHT SIDE BRACKET MECHANISM ................................................................................................................23

8.2 右边座机构 JK-6691-X

RIGHT SIDE BRACKET MECHANISM ................................................................................................................ 27

9.1 单针中座机构 JK-6691

SINGLE NEEDLE CENTRAL BRACKET MECHANISM.....................................................................................29

9.2 单针中座机构 JK-6691-X

SINGLE NEEDLE CENTRAL BRACKET MECHANISM.....................................................................................33

10.1 双针左边座及中座机构 JK-6692

DOUBLE NEEDLE LEFT SIDE BRACKET & CENTRAL BRACKET MECHANISM ....................................... 37

10.2 中座机构 JK-6681

CENTRAL BRACKET MECHANISM .................................................................................................................... 41

11. 倒针机构 JK-6692、JK-6691-X、JK-6681

DOUBLE NEEDLE REVERSE STITCHING MECHANISM ................................................................................45

12. 随机附件

ACCESSORIES ........................................................................................................................................................ 47

13. 电器连接图

ELECTRICITY ELEMENTS FIG ..............................................................................................................................49

1 本体机构
ARM BED AND IT'S ACCESSORIES

107A 108-1
104 110-1
109A 110-2 114B-1
110
110-3
104 110-4
110-5
105
119 115

120
116

106
103

102

152
151
101 151-1
151-1

127
(按型体配置)

127A
128
136
128
128-1

965B-03 131A
965B-10
965B-09 965B-01

965B-09 956-4
965B-08 956-6
965B-07 965B-02
956-5 956-1 147 130
965B-06
956-2 146
964 148
965B-04 957-1 956-3 149
965B-05 956
957-2 150 145
957 131-1
961 144
966-1 969B
961-1

966B 143
966-3
138 139B
966-2 132B
140 142
131
141 141-1
138A

1
1 本体机构
ARM BED AND IT'S ACCESSORIES
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
101
C01156 内六角圆柱头螺钉M5×25 Screw pan M5×25 1
102
C01220 内六角圆柱头螺钉M5×60 Screw pan M5×60 1
103
155211001 面板 Face palte 1
104
C01266 内六角盘头螺钉M4×8 Screw pan M4×8 8
105
155212001 松线防护板 Cover 1
106
15520100100 机壳组件 Machine shell components 1
107A
155212002 大防沙板 Cover 1
108-1
C01021 内六角盘头螺钉M5×10 Screw pan M5×10 2
109A
155211002 挑线杆防护罩 Thread takeup lever cover 1
110
155213004 绕线夹线器组件 Bobbin thread tension asm 1
114B
15523000200 电控组件/一体机 Machine electronic control 1
114C
15543000100 电控组件/一体机 Machine electronic control 1 6681专用电控
114B-1
C01156 内六角圆柱头螺钉M5×25 Screw pan M5×25 5
115
155213005 穿线杆 Spool pin 1
116
C01069 六角螺母 M6 Nut M6 1
119
155211003 油盖 Rubber plug 1
120
155211004 压棒盖 Rubber plug 1
127
155212003 支架 Bracket 1
127A
155212004 支架 Bracket 1
128
C01125 内六角圆柱头螺钉M6×10 Screw pan M6×10 3
128-1
C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 1
130
1550S11001 一字圆柱头螺钉M5×10 Screw pan M5×10 5
131
C01125 内六角圆柱头螺钉M6×12 Screw pan M6×12 3
131A
155212003 底盘座 Bottom cover 1
131-1
C01144 内六角圆柱头螺钉M6×10 Screw pan M6×10 3
132B
155212005 电磁铁安装板 Solenoid Mounting plate 1
136
1552S30001 脚柱 Bed leg 2
138A
155230001 抬压脚电磁阀 Elevating foot solenoid valve 1
141
15521200600 压脚弹片组 Pressure foot spring 1
141-1
C01022 平垫圈 Flat washer 2
142
1550S11013 一字圆柱头螺钉M4×8 Screw pan M4×8 2
143
15520100200 脚架连接块(组件） Connoctor 1
144
155212007 压脚提升弯杆 Bending rod 1
145A
155201003 脚架连杆头（组件） Connoctor 1
147
155212008 拉簧座 Tension spring seat 1
148
C01023 垫片 M5 Washer M5 2
149
C01130 内六角圆柱头螺钉M5×8 Screw pan M5×8 2
151
15523000800 机头三角按键组 Switch assembly 1
151-1
C01139 内六角圆柱头螺钉M3×6 Screw pan M3×6 2
155231019 面板标牌 Panel signs 1
956 155209018 开关压板 Switch plate 1
956-1 C01232 内六角凹端紧定螺钉M4×16 Screw pan M4×16 1
956-2 C01070 六角螺母 M4 Nut M4 1
956-3 155226009 限位柱 Limit column 1
956-4 155227004 栓销弹簧 Pin spring 1
956-5 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
956-6 C01092 内六角凹端紧定螺钉M4×4 Screw pan M4×4 1
957 155212038 倒缝把手座 Reverse feed lever fixing plate 1
957-1 C01243 内六角沉头螺钉M5×8 Screw pan M5×8 2
957-2 C01225 内六角圆柱头螺钉M3×14 Screw pan M3×14 2
961 155008007 定环 Stationary ring 1
961-1 1550S14001 螺钉 Screw 2
964 155202019 倒缝把手轴 Reverse feed lever shaft 1
965B-01 155201022 倒缝把手 Reverse feed lever 1

2
1 本体机构
ARM BED AND IT'S ACCESSORIES

107A 108-1
104 110-1
109A 110-2 114B-1
110
110-3
104 110-4
110-5
105
119 115

120
116

106
103

102

152
151
101 151-1
151-1

127
(按型体配置)

127A
128
136
128
128-1

965B-03 131A
965B-10
965B-09 965B-01

965B-09 956-4
965B-08 956-6
965B-07 965B-02
956-5 956-1 147 130
965B-06
956-2 146
964 148
965B-04 957-1 956-3 149
965B-05 956
957-2 150 145
957 131-1
961 144
966-1 969B
961-1

966B 143
966-3
138 139B
966-2 132B
140 142
131
141 141-1
138A

3
1 本体机构
ARM BED AND IT'S ACCESSORIES
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
965B-02 155201023 旋转把手组 Rotating handle 1
965B-03 155226010 固定销 Dowel pin 1
965B-04 C01092 内六角凹端紧定螺钉 Screw 1
965B-05 155208001 锁圈 Lock ring 1
965B-06 155227011 弹簧M4×5 Spring M4×5 1
965B-07 155209020 钢珠Sφ 8 Steel ball Sφ 8 1
965B-08 C01272 六角螺母 Nut 2
965B-09 C01030 平垫圈 Flat washer 2
965B-10 C01287 内六角圆头带垫螺钉M3×16 Screw pan M3×16 1
966B 155204012 倒缝摆杆 Rod of reverse stitching 1
966-1 C01134 内六角圆柱头螺钉M4×10 Screw pan M3×16 1
966-2 C01134 内六角圆柱头螺钉M4×10 Screw pan M3×16 2
966-3 C01022 平垫圈M4 Flat washer M4 2
969B 15523001300 点动开关 Inching switch 1

4
2 压棒机构
PRESSER FOOT BAR MECHANISM

231 238
232
233 234
239

240-1
240

240-2
235 202

236
229

237 236-1 204

246
247

248
205
201
203

249
247
221 242 226
248 205-1
241
220

219 224
243 244
223
222

208

206
228 207 218
228-1

227 218-1
211
210 212
210-1 213 214
215

217

5
2 压棒机构
PRESSER FOOT BAR MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
201 1550S11002 一字无头螺丝 Screw 1
202 155211005 一字无头调压螺丝 Screw 1
203 155212009 弹片压板 Shrapnel plate 1
204 155003001 压棒上套管 Upper casing of pressure bar 1
205 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 2
C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1 6692
205-1 C01172 内六角凹端紧定螺钉M5×5 Screw pan M5×5 1 6692
206 155001001 压棒固定座 Setting seat of pressure bar 1
207 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 2
208 155003002 压棒下套管 Running casing of pressure bar 1
210 155009001 轨导棒 Guide rods 1
210-1 C01088 内六角凹端紧定螺钉M5×8 Screw pan M5×8 1
211 155201004 轮前下座 Front seat 1
212 155201005 轮前连接座 Connecting seat 1
213 1550S11012 一字圆柱头螺丝 Screw 1
214 155027001 弹簧 Spring 1
215 155009002 顶针座 Thimble seat 1
217 B01001111 六角头螺栓M4×8 Bolt M4×8 1
218 155202001 压棒 Pressure bar 1
218-1 1550S15001 螺钉 Screw 1
219 1550S11003 一字圆柱头螺丝 Screw 1
220 155027002 弹簧 Spring 1
221 155004001 小夹线组件 Bobbin thread tensionasm 1
222 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
223 155004002 压棒提杆 Lifting rod of pressure bar 1
224 155203001 压棒提杆套管 Lifting sleeve of pressure bar 1
226 155201006 压棒提升器 Lifter of pressure bar 1
228A 155002001 压脚长轴 Presser foot long axis 1
228-1 C0196 轴用挡圈 Circlips for shaft 1
229 155028001 调整垫片 Washer 2
231 155012001 弹簧固定板 Spring fixing plate 1
232 155227003 离合拉簧 Clutch spring 1
233 155012002 弹簧固定板 Spring fixing plate 1
234 155227001 脚弓连接杠杆 Arch connecting lever 1
235 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 2
236 C01177 内六角锥端紧定螺钉M6×30 Screw pan M6×30 1
236-1 C01109 内六角平端紧定螺钉M6×35 Screw pan M6×35 1
237 C01069 六角螺母M6 Nut M6 2
238 155212025 开口挡圈M4 E rings M4 1
239 C01131 内六角圆柱头螺钉M6×8 Screw pan M6×8 1
240 155004003 上下输送臂 Upper and lower conveying arm 1
241 155202002 压棒提杆轴 Pressure rod lifting shaft 1
242 155208001 锁圈 Lock ring 1
243 C01092 内六角凹端紧定螺钉M4×4 Screw pan M4×4 1
244 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 2
246 155211012 线夹R-16.2 Clip R-16.2 1
247 C01022 平垫圈M4 Flat washer M4 2
248 C01139 内六角圆柱头螺钉 M4×8 Screw pan M4×8 2
249 155211010 油管护架 Tubing guard 1

6
3 天平及针棒摇动台机构
TAKE-UP LEVER & NEEDLE BAR ROCKING MECHANISM

305 303
SINGLE NEEDLE
单针 307
305-4 309
305-3 308
305-2 305-5 331 307
305-1

305-7

305-6 双针 331 332

305-15 DOUBLE NEEDLE 332 327-1 327
310
305-9 305-14 360
305-8 358 327-2
305-13
305-14

359
330A
306 330B
305-11 326
305-10
333
305-12 针
325 单 E
L
302 305-16 EED
327A N
LE
NG
334 SI 345
349
336 348
335
340
337
341
338
双针
DOUBLE NEEDLE
311
340 324

341-1 339
E
357 针 E NEEDL 324-1
双 OUBL
356
D
EL
DE
EN
EL
EL 针 GNI
DE 单S 313 323B-3
EN 342 311A 312 323B-1 311
EL 323B
针 BUO 344
双D 350 307 361
308 311
309 320 322
307 319 323B-2
343 315-1
324
352 315
351
314 321 324-1
353 346 315-2
354 328
353-1 单针
SINGLE NEEDLE 329

7
3 天平及针棒摇动台机构
TAKE-UP LEVER & NEEDLE BAR ROCKING MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
302 1550s12001 六角头螺丝M5×10 Screw pan M5×10 1
303 C01088 内六角凹端紧定螺钉M5×8 Screw pan M5×8 2
305 155238001 挑线杆组件 Thread take-up asm 1
155238002 挑线杆组件 Thread take-up asm 1 6692
306 155009003 针棒道引滑块 Needle bar guide slider 1
307 155012003 盘形垫片 Disc gasket 4 6691/6691-X/6681
308 155003003 套管 casing 2 6691/6691-X/6681
309 155024003 滚针轴承 Needle bearing 2 6691/6691-X/6681
310 155212013 调整垫片 Washer 1 6691/6691-X/6681
311 C01129 内六角圆柱头螺钉M6×16 Screw pan M6×16 2
C01129 内六角圆柱头螺钉M6×16 Screw pan M6×16 1 6692
311A C01132 内六角圆柱头螺钉 M5×12 Screw pan M5×12 1 6691/6691-X/6681
312 155201007 针送支臂 Needle delivery arm 1 6691/6691-X/6681
313 C01222 内六角圆柱头螺钉M5×14 Screw pan M5×14 1 6691/6691-X/6681
314 C0197 轴用弹性挡圈-A型 24 Circlips for shaft - type A 1 6691/6691-X/6681
315 155201008 凸轮连杆 Cam connecting rod 1 6691/6691-X/6681
315-1 155201009 凸轮连杆接块 Connecting block 1 6691/6691-X/6681
315-2 C01128 内六角圆柱头螺钉M4×6 Screw pan M4×6 1 6691/6691-X/6681
319 C01070 六角螺母M4 Nut M4 1 6691/6691-X/6681
320 C0189 内六角圆柱头螺钉M4×30 Screw pan M4×30 1 6691/6691-X/6681
321 155024001 滚针轴承 Needle bearing 1 6691/6691-X/6681
322 155209001 滑块凸轮 Slider cam 1 6691/6691-X/6681
323B 155209008 滑块凸轮导向座 Slide cam guide seat 1 6691/6691-X/6681
323B-1 155212010 固定块 Fixed block 1 6691/6691-X/6681
323B-2 155227004 弹簧 Spring 1 6691/6691-X/6681
323B-3 C01142 内六角圆柱头螺钉M3×6 Screw pan M3×6 2
324 155201010 滑块凸轮摆杆 Swinging rod of slider cam 1 6691/6691-X/6681
324-1 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
325 C01100 内六角沉头螺钉M4×6 Screw pan M4×6 2 6691/6691-X/6681
326 C01103 内六角沉头螺钉M4×8 Screw pan M4×8 2 6691/6691-X/6681
327 155212011 盖板 Cover plate 1
327-1 C0195 内六角沉头螺钉 M4×12 Screw pan M4×12 2
327-2 C01094 内六角凹端紧定螺钉M4×10 Screw pan M4×10 3
327A 155212012 电磁铁固定板 Electromagnet fixed plate 1 6691/6691-X/6681
328 155026001 固定（短)销 Pin （short） 1 6691/6691-X/6681
329 155024002 滚针轴承 Needle bearing 1 6691/6691-X/6681
330A 15523000300 针摆电磁铁(倒针切换） Needle pendulum electromagnet 1 6691/6691-X/6681
330B 155211006 尼龙垫 Nylon mat 1 6691/6691-X/6681
331 155008001 固定环 Retaining ring 1
332 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 1
335A 15520101100 针棒座组件 Needle bar support frame 1
336 155023001 油棉 Oil cotton 1
337 155009004 针棒连接器导槽 Needle bar connecting link guide 1
338 1550S11004 一字圆柱头螺丝 Screw 2
339 155023002 油棉 Oil cotton 1
340 155012017 油棉压板 Pressboard of oil cotton 3
341 1550S11013 一字圆柱头螺丝 Screw 2
341-1 C01092 内六角凹端紧定螺钉M4×4 Screw pan M4×4 1 6692
342 155002002 单针针棒 Needle bar 1 6691/6691-X/6681
343 155012004 针棒套环 Ring clamp 1 6691/6691-X/6681
344 1550S11006 螺钉 M3×0.5×4 Screw pan M3×0.5×4 1 6691/6691-X/6681
345 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 1 6691/6691-X/6681
346 155217001 车针 INDP×5#16 Needle INDP×5#16 6 6691/6691-X/6681
155217001 车针 INDP×5#16 Needle INDP×5#16 12 6692

8
3 天平及针棒摇动台机构
TAKE-UP LEVER & NEEDLE BAR ROCKING MECHANISM

305 303
SINGLE NEEDLE
单针 307
305-4 309
305-3 308
305-2 305-5 331 307
305-1

305-7

305-6 双针 331 332

305-15 DOUBLE NEEDLE 332 327-1 327
310
305-9 305-14 360
305-8 358 327-2
305-13
305-14

359
330A
306 330B
305-11 326
305-10
333
305-12 针
325 单 E
L
302 305-16 EED
327A N
LE
NG
334 SI 345
349
336 348
335
340
337
341
338
双针
DOUBLE NEEDLE
311
340 324

341-1 339
E
357 针 E NEEDL 324-1
双 OUBL
356
D
EL
DE
EN
EL
EL 针 GNI
DE 单S 313 323B-3
EN 342 311A 312 323B-1 311
EL 323B
针 BUO 344
双D 350 307 361
308 311
309 320 322
307 319 323B-2
343 315-1
324
352 315
351
314 321 324-1
353 346 315-2
354 328
353-1 单针
SINGLE NEEDLE 329

9
3 天平及针棒摇动台机构
TAKE-UP LEVER & NEEDLE BAR ROCKING MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
348 155227002 拉簧 Tension spring 1 6691/6691-X/6681
349 C01074 六角螺母M5 Nut M5 1 6691/6691-X/6681
350 155002003 双针针棒 Needle bar 1 6692
351 C01134 内六角圆柱头螺钉M4×10 Screw pan M5×12 1 6692
352 155008002 针棒套环 Ring clamp 1 6692
353 155201012 针榴3.2/2.8两种规格 Needle holder (3.2/2.8) 1 6692
356 1550S11007 螺钉 M5×0.8×6 Screw pan M3×0.8×6 1 6692
357 155012005 针棒座固定板 Needle bar fixing plate 1 6692
358 155003004 摆针轴左套管 Bushing 1 6692
359 C0184 内六角凹端紧定螺钉M6×8 Screw pan M6×8 1 6692
360 155003005 摆针轴右套管 Bushing 1 6692

10
4 缝线压力调整机构 UPPER THREAD TENSION REGULATION MECHANISM

418

405 417
406 417
416
404-1 414 416-1
404-2
404-3 410
404-4
404-5
404-6
404-7
409 404-8
413A 404-9
404-10
404-24
412-30(x2) 404-11 404-22
404 404-12
412-27
412-26 404-13
404-23
412-28(x2) 404-19
407 404-20
412-25 404-14 404-18 404-21
412-23
412-29(x2) 404-15 404-17
412-24 412-22
404-16
412-21 412-20
412-31
412-19
412-18
412-13
412-17

412-11
412-12
412-09 412 单针
412-10
415 SINGLE NEEDLE
412-08 412-16
412-15
412-07
412-14
411 412-06
412-05
412-04
412-03

412-02
412-01
419-33

419-30(x2) 419-22
419-21 419-20
419-27 419-26 419-23

419-22
419-28(x2)
419-21 419-20
419-34
419-18
419-25
419-29(x2) 419-17
419 双针 419-24
DOUBLE NEEDLE
419-32
419-19
419-13 419-16
419-31 419-12 419-15
419-14
419-10
419-09 419-11 419-18
415 419-08 419-17
419-16
419-15
419-07
419-14
411 419-06
419-05
419-04
419-03
419-02
419-01

11
4 缝线压力调整机构
UPPER THREAD TENSION REGULATION MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
404 15521300100 绕线器组件 Bobbin winder unit 1
405 C0184 内六角凹端紧定螺钉M6×8 Screw pan M6×8 2
406 155208003 锥形传动轮 Conical drive wheel 1
407 C0193 开槽沉头螺钉M4×8 Screw pan M4×8 1
409 C01021 内六角半圆头螺钉M5×10 Screw pan M5×10 1
410 15521201400 松线销组件 Tension releasing pin asm 1
411 C01088 内六角凹端紧定螺钉M5×8 Screw pan M5×8 1
412 15521300200 夹线组件 Thread tension asm 1 6691/6691-X/6681
413A 155213003 过线板 Thread tension guide plate 1
414 1552S16001 调整螺母 Adjiusting nut 1
415 C01021 内六角半圆头螺钉M5×10 Screw pan M5×10 2
416 155212015 松线阀座 Solenoid valve fixing plate 1
416-1 C01281 内六角圆柱头螺钉M3×6 Screw pan M3×6 2
417 C01106 内六角沉头螺钉M5×10 Screw pan M5×10 2
418 15523001100 电磁阀（松线） Solenoid valve (loose thread) 1
419 15521300300 夹线组件 Thread tension asm 1 6692

12
 5 主轴传动机构
UPPER & MAIN SHAFT TRANSMISSION MECHANISM

529-3
529
528(单针SINGLE NEEDLE)
528-1(双针DOUBLE NEEDLE)

529-5
513 529-2
529-4

529-1
512
527-1
506 509
527 517
503
501 502 508

517
527-1
507
519 518

525 526
520 527
525
521 522 523 510

517
524 517
525 538

535-8
535-6
535-5
535-4 521
535-3 535-10 517
535-9 539
535-1 535-7 534
546 540
534 541 559
535-2
557 545 559-1
558 559-2
535 542-7
533 542-6 559-3
542-5
559-10
542-4 559-4
542-3 559-11
559-5
542-2 559-9 559-6
542-8
559-5
559-8 559-7
542-11
544-1 542-1 542-10
537 536
560
561
544 543 542 542S
562 563 564

13
5 上轴及主传动机构
UPPER & MAIN SHAFT TRANSMISSION MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
501 1550S11008 螺钉（M5×13) Screw pan M5×13 2
502 1550S14001 螺钉（M6×0.75×6） Screw pan M6×0.75×6 2
503 155024004 滚珠轴承 (BB6204ZZNR) Ball bearing (BB6204ZZNR) 1
505 1550S14001 螺钉（M6×0.75×6） Screw pan M6×0.75×6 2
506 155202003 上轴 Upper shaft 1
507 155024005 滚珠轴承 (BB6004ZZNR) Ball bearing (BB6004ZZNR) 1
508 155003006 上轴套管 Casing of upper shaft 1
509 155225001 连轴器 Coupling 1
510 155035002 同步带 Synchronous belt 1
511 155235001 带轮调节机构 Pulley regulating mechanism 1
512 15523000400 电机 Motor 1
513 C01221 内六角圆柱头螺钉M5×20 Screw pan M5×20 4
517 1550S14001 内六角无头螺丝 M6×0.75×6Screw pan M6×0.75×6 12
518 1550S11009 一字半圆头定位螺丝 Screw 1
519 155001002 凸轮 Cam 1
591A 155210001 凸轮 Cam 1
519B 15521000200 凸轮组件 Cam asm 1
520 1550S15002 一字无头螺丝 Screw 1
521 155011002 保护盖 Protection cap 1
522 155029002 C型扣环 C-Retaining ring 1
523 155024006 滚珠轴承 (BB6203ZZNR) Ball bearing (BB6203ZZNR) 1
524 155202004 中轴 Shaft 1
525 155025001 齿形带轮(上） Timing wheel 2
526 155024005 滚珠轴承 Ball bearing 1
527 155003006 上轴套管 Upper shaft bushing 1
527-1 1550S14001 内六角无头螺丝 M6×0.75×6Screw pan M6×0.75×6 2
528 155011003 缝目指示环 Feed regulator scale 1
529 155211009 手轮 Handwheel 1
529-1 155203004 手轮连接盘 Handwheel connection plate 1
529-2 C0184 内六角凹端紧定螺钉M6×8 Screw pan M6×8 2
529-3 C01021 内六角平圆头螺钉M5×10 Screw pan M5×10 2
529-4 C0199 内六角圆头带垫螺钉M6×10 Screw pan M6×10 1
533 155202005 万向连接轴（长） Universal connecting shaft 1
533A 155202018 万向连接轴（长） Universal connecting shaft
534 1550S14001 螺钉（M6×0.75×6） Screw pan M6×0.75×6 2
535 15520101400 离合器组件 Clutch assembly 1
536 155024002 滚针轴承 Needle bearing 1
537 155026002 固定销（26) Dowel pin (26) 1
538 155035003 同步带 Synchronous belt 1
539 155025002 齿形带轮（下） Timing wheel(down) 1
540 155003007 轴承套管（右） Casing of bearing(right) 1
541 155024006 滚珠轴承 (BB6203ZZNR) Ball bearing (BB6203ZZNR) 1
542 15500100300 凸轮组件 Cam asm 1
542S C0184 内六角凹端紧定螺钉M6×8 Screw pan M6×8 2
543 155024014 滚珠轴承 (61906ZZ) Ball bearing (61906ZZ) 1
544 155005002 连杆 Connecting rod 1
544-1 155212016 垫片 Washer 1
545 1550240013 滚珠轴承 (BB6202ZZNR) Ball bearing (BB6202ZZNR) 1
546 155201015 剪线凸轮 Trimming cam 1
557 155208005 定环 Fixed ring 1
558 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 2
559 15521201700 送料调整按钮（组件） Feeding adjustment button asm 1
560 C0221 开槽圆柱头螺钉M4×10 Screw pan M4×10 1
561 155227010 压簧 Compression spring 1
562 C01020 平垫圈M6 Flat washer M6 1
563 155226003 按钮销 Button pin 1
564 155208008 开口挡圈 E rings 1

14
6.1 下送料、剪线机构 (JK-6691 、JK-6692)
LOWER FEED & THREAD TRIMMING MECHANISM

307
双针 308
DOUBLE NEEDLE 307
309

604-1 603
606
607-1
607 602 615
608
614
609

611

307
309 610
308 613A
307 307
309 612
602
601 308
307 617
616
616
E
EEDL
603 613 641
针
单 INGLE N
S
604
617 648 611
609 608
606 640

607-1
614 双针
DOUBLE NEEDLE
607 EL
DE
EN
609 620 EL 621
608 单针 625 针 GNI 623
SINGLE NEEDLE 626 单S 624
618
619
双针
DOUBLE NEEDLE
623
620 620 621

642 618 627

619

646
628
624
623 645 631
636 635
621 623 629
644 630
643 639
639-1
619 632
638
647 633
637 634

15
6.1 下送料及剪线机构 (JK-6691、JK-6692)
LOWER FEED & THREAD TRIMMING MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
307 155012003 盘形垫片 Disc gasket 6
308 155003003 轴承套管 Casing of bearing 3
309 155024003 滚针轴承 Needle bearing 3
601 C01043 轴用挡圈M15 Circlips for shaft M15 1
602 155012008 垫片 Washer 2
603 155202006 下送料轴 Feed rocker shaft 1
604 155004005 万向连接头 Crank 1
604-1 155004006 万向连接头 Crank 1 6692
606 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 1
607 155004007 万向连接座 Clamp 1
607-1 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 1
608 55S011016 一字圆柱头螺丝 Screw 2
609 155023003 油棉垫 Oil cotton pad 2
610 155026002 固定销（长） Dowel pin 1
611 155024002 滚针轴承 Needle bearing 2
612 155005003 连杆 Connecting rod 1
613 155204005 右单向输送支臂 Right one-way delivery arm 1 6692
613A 155204006 单向输送支臂 One-way delivery arm 1 6691/6691-X/6681
614 1550S14001 螺钉（M6×0.75×6） Screw pan M6×0.75×6 2
615 155008004 固定环 Retaining ring 1
616 C01212 内六角凹端紧定螺钉M5×4 Screw pan M5×4 2
617 C01159 内六角圆柱头螺钉M5×16 Screw pan M5×16 2
618 155205004 摆杆 Swinging rod 1
619 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 1
620 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
621 155226004 摆杆销（短） Pendulum pin 1
623 C01020 平垫圈M6 Flat washer M6 2 6691/6691-X/6681
C01020 平垫圈M6 Flat washer M6 3 6692
624 155212018 拉杆 Pull rod 1
625 155226005 拉簧销 Tension spring pin 1
626 155227005 拉簧 Tension spring 1
627 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
630A 15520400800 离合器臂（组件） Clutch arm (asm) 1
631 155202007 离合器轴 Clutch shaft 1
632 155209010 剪线座 Trimmer 1
633 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
634 C01157 内六角圆柱头螺钉M5×30 Screw pan M5×30 2
635 C01100 内六角沉头螺钉M4×6 Screw pan M4×6 2
636 155212019 电磁铁固定板 Electromagnet fixing plate 1
637 C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 2
638 15523000600 电磁铁（剪线） Electromagnet（trimming) 1
639 155211006 尼龙垫 Nylon mat 1
639-1 C01066 六角薄螺母M4 Nut M4 2
640 155026002 固定销(长) Dowel pin（length) 1
641 155004008 左单向输送支臂 Left one-way delivery arm 1 6692
641A 155204001 左单向输送支臂 Left one-way delivery arm 1
642 155205005 双针左摆杆 Left swing rod of Double needle 1 6692
643 155226006 摆杆销 Pin of swinging rod 1 6692
644 C01022 平垫圈 Flat washer 2 6692
645 155212020 切线连接块一 Tangent connecting block 1 1 6692
646 155212021 切线连接块二 Tangent connecting block 2 1 6692
647 C01023 平垫圈M5 Flat washer M5 2
648 C01085 内六角凹端紧定螺钉M5×4 Screw pan M5×4 1 6692

16
6.2 下送料、剪线机构 (JK-6691-X、JK-6681)
LOWER FEED MECHANISM

307
308
309
307

615
614

611

307
309 610
308 613A
307 307
309 612
602
601 308
307 617
616
616
603

604
611
606 609 608 640

607-1
607

609
608
DT983
DT984
DT985
DT982
DT981 DT987
DT980 DT986
DT979
DT919-1
DT919 DT977
DT976 DT973
DT919-2
DT978
DT974

DT972

DT975 DT969
DT965 DT968
DT964 DT971
DT988
DT970
DT963 DT966 DT967

17
6.2 下送料、剪线机构零件明细 （JK-6691-X、JK-6681）
LOWER FEED MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
307 155012003 盘形垫片 Disc gasket 6
308 155003003 培林套管 Bearing casing 3
309 155024003 滚针轴承 Needle bearing 3
601 C01043 轴用挡圈M15 Circlips for shaft M15 1
602 155012008 垫片 Washer 1
603 155202006 送料轴 Feed rocker shaft 1
604 155004005 万向连接头 Crank 1
606 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 1
607 155004007 万向连接座 Clamp 1
607-1 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 1
608 55S011016 一字圆柱头螺丝M4×10 Screw pan M4×10 2
609 155023003 油棉垫 Oil cotton pad 2
610 155026002 固定销（长） Dowel pin(long) 1
611 155024002 滚针轴承 Needle bearing 2
612 155005003 连杆 Link 1
613A 155204006 单向输送支臂 One-way delivery arm 1
614 1550S14001 内六角无头螺丝 Screw 2
615 155008004 固定环 Retaining ring 1
616 C01085 内六角凹端紧定螺钉M6×6 Screw pan M6×6 3
617 C01159 内六角圆柱头螺钉M5×16 Screw pan M5×16 2
640 155026002 固定销(长) Dowel pin 1
DT919 155405002 刀轴摆杆 Pendulum of knife shaft 1
DT919-1 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 2
DT919-2 C01169 内六角圆柱头螺钉M3×6 Screw pan M3×6 1
DT963 155426005 凸轮销A Pin of cam A 1
DT964 155412004 钢球 Steel ball 1
DT965 155401007 剪线定位座 Thread trimming seat 1
DT966 155408007 隔套 Spacer 1
DT967 C01092 内六角凹端紧定螺钉M4×4 Screw pan M4×4 1
DT968 155426006 提升把手销 Pin of lift handle 1
DT969 155405003 拉杆接头 Connector of pull rod 1
DT970 C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 2
DT971 C01100 内六角沉头螺钉M4×8 Screw pan M4×8 4
DT972 155412005 电磁铁固定板 Electromagnet fixed plate 1
DT973 155430001 电磁铁 Electromagnet 1
DT974 155405004 剪线拉杆 Trimming pull rod 1
DT975 C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 1
DT976 155426007 摆动拉杆销 pull rod 1
DT977 155402005 剪线摆杆轴 Trimming pendulum shaft 1
DT978 C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 1
DT979 155426008 摆杆销 Pin of swinging rod 1
DT980 155402006 摆动拉杆 swinging lever 1
DT981 C01087 内六角凹端紧定螺钉M3×6 Screw pan M3×6 1
DT982 155426009 摆动拉杆销 Pin of swinging lever 1
DT983 C01074 螺母M4 Nut M4 1
DT984 155402007 剪线摆杆 Trimming pendulum 1
DT985 C01085 内六角凹端紧定螺钉M5×4 Screw pan M5×4 2
DT986 155427001 拉簧 Tension spring 1
DT987 155426010 拉杆销 Pin of pull rod 1
DT988 C01023 平垫圈M5 Flat washer M5 3

18
7.1 轮前、上边心机构 (被动送料)
ROLLER PRESSER FOOT & UPPER SIDE SHAFT MECHANISM

704

718 710
744
718-1 743 731
718-16
718-14
730
718-2 718-15 701
718-3 718-13
718-12
718-2 702
711
718-4
718-11 703
718-10
718-9
718-5 718-8
718-7

718-6

706 707
716

705 706

709 715
723
729
708 728
714 724
722
725
713
307 712
308
309 727
307 704-1 734
721
734 733 726
单针 720
SINGLE NEEDLE
732 734 725
732 719
733
732 724
740 738 732
734 725
737 739
727
736 718
双针 734
735 DOUBLE NEEDLE

726
717
741 307
742 309 725
308
307 724

19
7.1 轮前及上边心机构(被动送料)
ROLLER PRESSER FOOT & UPPER SIDE SHAFT MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
307 155012003 盘形垫片 Disc gasket 4
308 155003003 轴承套管 Casing of bearing 2
309 155024003 滚针轴承 Needle bearing 2
701 C01128 内六角圆柱头螺钉 M4×6 Screw pan M4×6 2
702 155201016 轮前倒针座 Holder of backstitch 1
703 155203006 后套 Counter 1
704 C0207 圆柱销 3×18（u级） Cylindrical pin 3×18 (u grade) 1
704-1 C0186 圆柱销 3×16（u级） Cylindrical pin 3×16 (u grade) 1
705 155226007 固定销 Dowel pin 1
706 C01130 内六角圆柱头螺钉 M5×8 Screw pan M5×8 2
707 155204009 离合器后摆杆 Clutch rear swing lever 1
708 155204010 离合器前摆杆 Clutch front swing lever 1
709 155203007 前套 Toe cap 1
710 155209004 万向轴承座 Universal bearing holder 1
711 C01218 内六角圆柱头螺钉M6×35 Screw pan M6×35 2
712 C0203 轴用挡圈 16 Circlips for shaft 1
713 155209005 摆杆连接块 Connecting block of swing bar 1
714 155212022 垫片 Washer 1
715 155227006 压簧 Compression spring 1
716 15523000700 上轮钱倒针电磁阀 Backstitch solenoid valve 1
717 1550S11012 一字圆柱头螺丝 Slotted head screw 1
718 155225003 轮钱组件/30中号/白色 Roller press asm/30medium/white 1
719 155225004 轮钱倒针下离合器 Lower clutch of backstitch 1
720 155225005 轮钱倒针上离合器 Upper clutch of backstitch 1
721 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 2
722 155202008 滚轮联接轴上节 Roller coupling shaft (upper) 1
723 C01278 弹性销 3×10 Elastic pin 3×10 1
724 155012010 E型扣环 E-type buckle 4
725 155012011 调整垫片 Adjusting washer 6
726 155024009 单向轴承座 One-way bearing holder 2
727 155024010 滚针轴承 Needle bearing 2
728 155227010 压簧 Compression spring 1
729 155212023 垫圈 Washer 1
730 155024011 万向轴承座 Universal bearing 1
731 155012013 C行扣环 C-shaped buckle 2
732 155023003 油棉垫 Oil cotton pad 4
733 155005005 万向连杆 Universal connecting rod 2
734 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 4
735 155004005 万向连接头 Crank 1
736 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 1
737 155012008 垫片 Washer 1
738 155004007 万向连接座 Clamp 1
739 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 1
740 155202009 上边心轴 Shaft 1
741 155008001 固定环 Retaining ring 1
742 1550S14001 内六角无头螺钉M6×0.75×6 Screw pan M6×0.75×6 1
734 C01099 内六角沉头螺钉M5×12 Screw pan M5×12 2
744 155009007 连接块 Link block 1

20
7.2 轮前、上边心机构(-1型) (主动送料)
ROLLER PRESSER FOOT & UPPER SIDE SHAFT MECHANISM

BF704
BF705
BF706

BF718

BF718-6

BF745 BF718-7
BF742 BF718-1
BF718-2
BF718-2
BF735
BF718-3
BF748
BF718-3
BF710 BF747
BF734 BF718-2
BF749 BF704 BF718-2
BF750 BF706 BF718-1
BF707 BF701
BF747 BF749 BF702
BF713 BF751 BF718-4
BF705
BF703
BF711 BF701
BF748 BF702
BF712 BF708 BF718-5
BF707 BF706
BF709 BF735
BF715 BF736
BF702 BF704
BF701
BF703
BF737
BF702 BF736
BF701 BF714 BF739 BF738
BF723 BF726
BF743 BF725 BF733
BF742
BF744 BF706
BF742 BF732
BF743
BF741 BF705
BF730
BF719-16 BF724 BF731 BF704
BF719-15 BF720
BF728
BF727
BF719-14
BF721
BF719-1
BF729
BF719-2 BF719-13 BF740
BF719-3 BF719-12
BF719-10 BF728
BF719-2 BF746 BF727
BF719-4

BF719-11 BF719
BF719-5 BF719-9
BF719-7 BF719
BF719-6 BF719-8

21
7.2 轮前及上边心机构 ﴾‐1型﴿ ﴾主动送料﴿
ROLLER PRESSER FOOT & UPPER SIDE SHAFT MECHANISM

序号 件号 零部件名称 Name of parts 数量 备注

N0. Part No. Amt.
BF701 1550S11016 一字圆柱头螺丝M4×10 Screw pan M4×10 4
BF702 155023003 油棉垫 Oil cotton pad 4
BF703 155205006 万向连杆 Universal connecting rod 2
BF704 155012014 C型扣环 C-shaped buckle 2
BF705 155212024 调整垫片 Adjusting washer 3
BF706 155024012 轴承 608ZZ Bearing 608ZZ 4
BF707 155224012 单向培林座 One-way bearing holder 2
BF708 155024010 滚针轴承 Needle bearing 2
BF709 155202010 培林轴 Shaft 1
BF710 155202011 上边心轴 Shaft 1
BF711 155012008 垫片 Washer 2
BF712 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 1
BF713 155004006 万向连接头 Crank 1
BF714 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 1
BF715 155004007 万向连接座 Clamp 1
BF718 B01019006 倒缝齿轮芯轴组件 Backstack gear spindle asm 1
BF719 155225003 轮钱组件 Upper feeding wheel asm 1
BF720 C01092 内六角凹端紧钉螺钉M5×4 Screw pan M5×4 4
BF721 155503001 万向连轴器 Universal 1
BF723 155204011 倒针摆杆 Rod of reverse stitching 1
BF724 155202012 旋转轴 Rotating shaft 1
BF725 C01083 内六角凹端紧钉螺钉M4×6 Screw pan M4×6 1
BF726 155228001 垫片 Washer 1
BF727 C01083 内六角凹端紧钉螺钉M4×5 Screw pan M4×5 4
BF728 155208004 锁圈 Lock ring 2
BF729 155209003 弓形件 Bow 1
BF730 155227007 拉簧 Tension spring 1
BF731 C01281 内六角圆柱头螺钉M3×8 Screw pan M3×8 1
BF732 C01030 平垫片 Flae washer 1
BF733 155209011 拉簧固定座 Setting seat of tension spring 1
BF734 1550S14001 螺丝M6×0.75×6 Screw M6×0.75×6 2
BF735 155225013 斜锥齿轮A Bevel gear A 1
BF736 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 2
BF737 155201017 轮钱倒缝座 Upper feed wheelasm seat 1
BF738 C01086 内六角凹端紧钉螺钉M5×6 Screw pan M5×6 1
BF739 C01227 内六角圆柱头螺钉M3×4 Screw pan M3×4 1
BF740 C01049 圆柱销﴾B型‐h级﴿3×28 Cylindrical pin(B-h)3×28 1
BF741 155202013 弓形件滑动轴 Bow sliding shaft 1
BF742 C01132 内六角圆柱头螺钉M5×10 Screw pan M5×10 2
BF743 C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 2
BF744 155212026 电磁铁固定板 Electromagnet fixed plate 1
BF745 155209012 连接板 Connectionn plate 1
BF746 15523000300 电磁铁（上下倒针切换） Electromagnet 1
BF747 155008001 固定环 Retaining ring 2
BF748 1550S14001 螺钉 Screw 2
BF749 155012003 盘形垫片 Disc gasket 4
BF750 155003003 培林套管 Bearing casing 2
BF751 155024003 滚针轴承 Needle bearing 2
BF752 1550S11017 一字圆柱头螺丝 Screw pan 2
BF753 C01130 内六角圆柱头螺钉M5×8 Screw pan M5×8 2
BF754 1550S11018 一字圆柱头螺丝 Screw pan 1

22
8.1 右边座机构 (JK-6691、JK-6692)
RIGHT SIDE BRACKET MECHANISM

839
802-2 838
801 802-3 843
802 802-1 830 829 832
836
802-4 833 844 843-4 843-1
804 802-6
802 802-5 843-5
831
828 802-7 837

827 802-8
840
826 802-10 802-9 843-2
841 846
841A 842 843-3
834 845
805A 835 847
841-1
805 821 822 818-1 819

818-2 EL
819 DE
873 EN
820 824 EL
针 ELD 821 822
823 810 针 BUO
单 EE 811 双D
N
806 EL
GN 819
808 IS EL
DE
855
873
EN
854 EL
针 BUO
818 双D
819
870
825
817 809

852
816 单针
SINGLE NEEDLE

869
863 877
808 814 866
871 876
872
868 815 871-1 双针 860
DOUBLE NEEDLE 874
851 874-1
807
812 850 875 861
869 813 876 865
849 848 单针 862
双针 854-1 SINGLE NEEDLE
814 DOUBLE NEEDL
848
E
856A 单针
SINGLE NEEDLE 857
856B 双针
815
854-1
855-1 DOUBLE NEEDLE 858
849
855-1 859

23
8.1 右边座机构 (JK-6691、JK-6692)
RIGHT SIDE BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
801 1550S11014 螺丝 M5×0.8×20 Screw pan M5×0.8×20 1
802 15521800100 旋梭组件 Hook asm 1
804 155209013 大釜护盖 Cauldron fender 1
805A 15520201400 单针釜轴套管组件 Hook driver 1
807 155228002 轴承垫片 Bearing gasket 1
809 155221001 油管 Tubing 1
810 15522100200 油管(组件) Tubing (asm) 1
811 1550S11013 开槽圆柱头螺钉M4×6 Screw pan M4×6 1
812 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 2
813 155203008 下套管 Running casing 1
814 155229001 卡簧 Circlip 2
815 155203009 斧轴套管 Axe shaft casing 2
816 155223001 油棉垫 Oil cotton pad 1
817 C01040 孔用挡圈M28 Circlips for hole 1
818 155201018 单针边座 Single needle side seat 1
818-1 C0194 内六角圆柱头螺钉M6×16 Screw pan M6×16 2
818-2 155028002 垫片 Washer 2
819 C01266 内六角平圆头螺钉M4×8 Screw pan M4×8 10
820 155212027 边盖板(单针） Side cover (single needle) 1 6691/6691-X/6681
821 155026003 调整销 Adjustig pin 2
822 C01093 内六角凹端紧定螺钉M4×8 Screw pan M4×8 2
823 1552S11001 开槽圆柱头螺钉 Screw 1
824 155212028 弹簧板 Spring plate 1
826 155222001 橡皮垫 Rubber mat 1
827 155228003 垫片 Washer 1
828 C01044 轴用挡圈M20 Circlips for shaft 1
829 155226008 调节销 Adjustig pin 1
830 1552s11002 螺钉 Screw 1
831 155219001 定刀 Fixed knife 1
832 155212029 弹片 shrapnel 1
833 1552S11003 螺钉 Screw 1
834 C01083 内六角凹端紧定螺钉M4×5 Screw pan M4×5 2
836 C01161 内六角圆柱头螺钉M4×25 Screw pan M4×25 1
838 155219002 动刀 Moving knife 1
839 C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 1
840 C01147 内六角圆柱头螺钉M4×12 Screw pan M4×12 1
841A 15520101900 刀座组件 Tool holder assembly 1
841-1 155212030 刀座垫片 Gasket of Tool holder 0
843 15521203100 大釜盖组件 Post cap 1
843-1 C01266 内六角平圆头螺钉M4×8 Screw pan M4×8 2
844 155202015 牛 角 Rotating hook opener 1
845 C01147 内六角圆柱头螺钉M4×12 Screw pan M4×12 1
846 C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 1
847 155209014 牛角固定座 Rotating hook opener bracket 1
848 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 2
849 155025003 大齿轮 Bevel gear(large) 1
850 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 2
851 155025004 小齿轮 Bevel gear(small) 1
852 155212032 边盖板 Side cover 1 6691/6691-X/6681
854 C01085 内六角凹端紧定螺钉M5×4 Screw pan M5×4 2
854-1 1550S14001 内六角无头螺钉 M6×0.75×6Screw pan M6×0.75×6 2
855 155208005 定环 Stationary ring 1
855-1 155008006 定环 Stationary ring 1
856A 155202016 万向连接轴 Universal connecting shaft 1 6691/6691-X/6681

24
8.1 右边座机构 (JK-6691、JK-6692)
RIGHT SIDE BRACKET MECHANISM

839
802-2 838
801 802-3 843
802 802-1 830 829 832
836
802-4 833 844 843-4 843-1
804 802-6
802 802-5 843-5
831
828 802-7 837

827 802-8
840
826 802-10 802-9 843-2
841 846
841A 842 843-3
834 845
805A 835 847
841-1
805 821 822 818-1 819

818-2 EL
819 DE
873 EN
820 824 EL
针 ELD 821 822
823 810 针 BUO
单 EE 811 双D
N
806 EL
GN 819
808 IS EL
DE
855
873
EN
854 EL
针 BUO
818 双D
819
870
825
817 809

852
816 单针
SINGLE NEEDLE

869
863 877
808 814 866
871 876
872
868 815 871-1 双针 860
DOUBLE NEEDLE 874
851 874-1
807
812 850 875 861
869 813 876 865
849 848 单针 862
双针 854-1 SINGLE NEEDLE
814 DOUBLE NEEDL
848
E
856A 单针
SINGLE NEEDLE 857
856B 双针
815
854-1
855-1 DOUBLE NEEDLE 858
849
855-1 859

25
8.1 右边座机构 (JK-6691、JK-6692)
RIGHT SIDE BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
856B 155202017 万向连接轴 Universal connecting shaft 1 6692
857 155211010 油管护架 Tubing guard 1
858 C01022 平垫圈M5 Flat washer M5 1
859 C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 1
860 155221003 油管 Tubing 1
861 155212033 线卡 Ply-yard drill 1
862 C01127 内六角圆柱头螺钉M4×16 Screw pan M4×16 1
863 155212034 护线架 Thread guard 1
865 155236001 油管接头 The tubing connector 1 6691/6691-X/6681
866 155211011 油镜 Oil mirror 1
868 155224013 平面轴承 Plane bearing 1
869 155224014 滚针轴承 Needle bearing 2
870 B94049 滚珠轴承（6001-2RZ/Z2） Ball bearing（6001-2RZ/Z2） 1
871 155008007 定环 Stationary ring 1
871-1 155228005 垫片 Washer 2
872 1550S14002 内六角无头平端螺丝 Screw 2
873 155212035 双针边盖板 Side cover of double needle 2 6692
874 155236002 油管接头 三通 The tubing connector Tee 1 6692
874-1 155221004 油管 Tubing 1 6692
875 155212036 线卡 Ply-yard drill 1 6692
876 C01139 内六角圆柱头螺钉M4×10 Screw pan M4×10 1 6692
877 C0198 O型圈 32×1 O-ring 32×1 1 6692

26
8.2 右边座机构 （JK-6691-X）
RIGHT SIDE BRACKET MECHANISM

DT901
DT902 DT953 DT951

DT903 DT954 DT950

DT904 DT947 DT949
DT905
DT946 DT948
DT944
DT906 DT955 DT924
DT940 DT559 DT940
DT907
DT956 DT945
DT943
DT939
DT939
DT908

DT942
DT941
DT911
DT938
DT936
DT909 DT937 DT935
DT910 DT957

DT934

DT933
DT907 DT935

DT912 DT930
DT913 DT933 DT932
DT914 DT931
DT929
DT928

DT912 DT927
DT913
DT919
DT915
DT919-1
DT920
DT916 DT922
DT921
DT922
DT958
DT917
DT918 DT924
DT923

DT926

27
8.2 右边座机构零件明细 （JK-6691-X）
RIGHT SIDE BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
DT901 155418001 梭仔子 Shuttle 1
DT902 15541800100 旋梭 Hook 1 进口旋梭
DT903 155405001 牛角摆杆 Rotating hook opener pendulum 1
DT904 155426004 牛角摆杆销 Rotating hook opener swing pin 1
DT905 155419002 动刀 Movable knife 1
DT906 155428004 平垫片 Flat Washer 1
DT910 15540200100 釜轴套管（组件） Axe shaft casing（asm） 1
DT911 C01227 内六角圆柱头螺钉 Screw pan 1
DT912 C01093 内六角凹端紧定螺钉M4×6 Screw pan M4×6 2
DT913 155026003 调整销 Adjustig pin 2
DT914 155403001 釜轴大套管 Axe shaft large casing 1
DT915 155408008 釜轴下衬套 Axe shaft lower bushing 1
DT916 155424001 滚针轴承 Needle bearing 1
DT917 155408006 釜轴下锁圈 Axe shaft locking ring 1
DT918 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 2
DT920 155408005 定环 Stationary ring 1
DT921 155425007 小齿轮 Bevel gear(samll) 1
DT922 1550S14003 螺钉 Screw 2
DT923 15542100100 油管组件 Tubing components 1
DT924 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 4
DT926 C01142 内六角圆柱头螺钉M3×8 Screw pan M3×8 2
DT927 155402008 万向连接轴（短） Universal connecting shaft(short) 1
DT928 155408003 定环 Stationary ring 1
DT929 155425005 大齿轮 Bevel gear(large) 1
DT930 1550S14001 螺钉M6×0.75×6 Screw M6×0.75×6 2
DT931 C01040 孔用挡圈 Circlips for hole 2
DT932 B94049 轴承6001-2RZ Bearing 6001-2RZ 2
DT933 C01083 内六角凹端紧定螺钉M4×5 Screw pan M4×5 4
DT934 155401002 剪线凸轮 Trimming cam 1
DT935 155408003 锁圈 Lock ring 2
DT936 C01212 内六角凹端紧定螺钉M6×6 Screw pan M6×6 2
DT937 155428002 垫片 Washer 4
DT938 C0194 内六角圆柱头螺钉M6×16 Screw pan M6×16 4
DT939 155212006 边盖板 Side cover 2
DT940 C01266 内六角平圆头螺钉M4×8 Screw pan M4×8 8
DT941 1552S11001 开槽圆柱头螺钉M4×6 Screw pan M4×6 1
DT942 155212028 弹簧板 Spring plate 1
DT943 C01127 内六角圆柱头螺钉M4×16 Screw pan M4×16 2
DT944 1554S10001 动刀螺丝 Screw 2
DT945 C01280 圆柱销3×8 Cylindrical pin3×8 2
DT946 155426001 牛角座销 Rotating hook opener bracket pin 1
DT947 C01093 内六角凹端紧定螺钉M4×6 Screw pan M4×6 1
DT948 1554S10004 牛角螺钉 Screw 1
DT949 155402002 牛角 Rotating hook opener 1
DT950 155409002 牛角座 Rotating hook opener bracket 1
DT951 1554S10005 牛角销螺钉 Screw 1
DT953 15521203100 釜盖组件 Kettle cover assembly 1
DT954 C01266 内六角平圆头螺钉M4×8 Screw pan M4×8 2
DT955 155412001 夹线弹片 Clipping shrapnel 1
DT956 155401005 夹线弹片座 Clipping shrapnel seat 1
DT957 155201018 单针边座 Single needle side seat 1
DT958 155412003 油管支架 Tubing bracket 1
DT959 155409005 牛角座接块 Rotating hook opener bracket linker 1

28
9.1 单针中座及下倒缝机构 (JK-6691)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM

901-1
901-2A/小孔 SMALL
901-2B/中孔MEDIUM
901-2C/大孔 LARGE
920-7
920-6
901-3 920-5
920-4
920-3 920-9
901 920-8
920-10
920-11
920-2 920-1 920-12
903 902 908

920-13

920
904
907 919
915S 918
909 911 911S 912
911S 913 921
905
917S
913S 919
906
916S 917S 918
910 919S 916C
911S
916
913S
915

817 915S
915S 917
914S 916S
913S
930S
732 916A
870
952S 915
870-1 727
870-2 914
929S 928S 913

732
930S 928S 948S

727 945S

943S XW76
947S
939S
938S 944S 951S
943S-1
946S 951S
931S 915S 950D
935S 914S 941S
933S 942S
932S 911S 913S
934S 936S
931S-2 937S
931S-1

29
9.1 单针中座及下倒缝机构 (JK-6691)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
727 155024010 滚针轴承 Needle bearing 2
732 155023003 油棉垫 Oil cotton pad 2
817 C01040 孔用挡圈 28 Circlips for hole 1
870 B94049 轴承6001-2RZ Bearing 6001-2RZ 1
870-1 155208007 定环 Stationary ring 1
870-2 C01083 内六角凹端紧定螺钉M4×5 Screw pan M4×5 2
901 15521500100 单针针板 Throat plate 1
902 155028002 垫片 Washer 2
903 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 2
904 1550S11015 一字圆柱头螺丝 Screw 1
905 C0194 内六角圆柱头螺钉M6×16 Screw pan M6×16 2
906 155028002 垫片 Washer 2
907 155026005 调整销 Adjustig pin 1
908 C0193 开槽沉头螺钉M4×8 Screw pan M4×8 2
909 C01091 内六角凹端紧定螺钉M4×10 Screw pan M4×10 1
910 155211004 压棒盖 Cover for pressing stick 1
911 155201025 单针中座 Support plate 1
912 155025006 中座小齿轮 Bevel gear 1
913 1550S14001 螺钉M6×0.75×6 Screw M6×0.75×6 4
914 155025007 中座小齿轮 Bevel gear 1
915 C01083 内六角凹端紧定螺钉M4×6 Screw pan M4×6 2
916 155203010 套管 Casing 1
916A 155003009 下套管 Running casing 1
916C 155224015 滚针轴承 Needle bearing 1
917 155002005 中座轴 Shaft 1
918 C01085 内六角凹端紧定螺钉M5×4 Screw pan M5×4 4
919 155009009 轴连接器 Shaft connector 2
920 15522500800 单针送金组件 Single needle feeding component 1
921 155011005 塑料接头 Plastic connector 1
911S C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 7
913S 155012014 C型扣环 C-shaped buckle 4
914S 155228006 调整垫片 Adjiusin washer 2
915S 155024012 轴承608ZZ Bearing 608ZZ 4
916S 155002006 轴承轴 Bearing shaft 2
917S 155225006 锥形齿轮 Bevel gear 2
919S 155225007 锥形齿轮 Bevel gear 1
928S 155224016 单向轴承座 NA/SK One-way bearing holder NA/SK 2
929S 155205007 万向连杆A Universal connecting rod A 1
930S C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 2
931S 155201024 倒针座 Holder of backstitch 1
931S-1 C01145 内六角圆柱头螺钉M6×20 Screw pan M6×20 2
931S-2 C01020 平垫圈M6 Flat washer M6 2
932S C0177 内六角平端紧定螺钉M4×16 Screw pan M4×16 1
933S C01070 六角螺母M4 Nut M4 1
934S C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 1
935S 155226011 滑动销 Sliding pin 1
936S C01134 内六角圆柱头螺钉M4×8 Screw pan M4×8 2
937S 155212039 滑块限位座 Limited seat of slider 1
938S 155226012 调节销 Adjustig pin 1
939S 155227017 压簧 Compression spring 2
941S C01022 平垫圈M4 Flat washer M4 2
942S C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 2
943S 155209017 倒针滑块 Slider of backstitch 1
943S-1 155211007 滑套 Sliding sleeve 1

30
9.1 单针中座及下倒缝机构 (JK-6691)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM

901-1
901-2A/小孔 SMALL
901-2B/中孔MEDIUM
901-2C/大孔 LARGE
920-7
920-6
901-3 920-5
920-4
920-3 920-9
901 920-8
920-10
920-11
920-2 920-1 920-12
903 902 908

920-13

920
904
907 919
915S 918
909 911 911S 912
911S 913 921
905
917S
913S 919
906
916S 917S 918
910 919S 916C
911S
916
913S
915

817 915S
915S 917
914S 916S
913S
930S
732 916A
870
952S 915
870-1 727
870-2 914
929S 928S 913

732
930S 928S 948S

727 945S

943S XW76
947S
939S
938S 944S 951S
943S-1
946S 951S
931S 915S 950D
935S 914S 941S
933S 942S
932S 911S 913S
934S 936S
931S-2 937S
931S-1

31
9.1 单针中座及下倒缝机构 (JK-6691)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
944S 155209006 顶杆挡块 Baffle plate of ejection pin 1
945S C01142 内六角圆柱头螺钉M3×8 Screw pan M3×8 2
946S 155220001 螺钉 Screw 1
947S 155212040 顶杆 Ejection pin 1
948S 15523000300 下送金倒针电磁阀 Solenoid valve for backstitch 1
950D 155212041 下倒针电磁阀座 Solenoid valve seat 1
951S C01137 内六角圆柱头螺钉M5×8 Screw pan M5×8 3
952S 155205008 万向连杆B Universal connecting rod B 1
×W76 155227016 锥形弹簧 Conical spring 1

32
9.2 单针中座及下倒缝机构 (JK-6691-X)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM

901-3
901-2
920-7
920-6
920-5
901-1 920-4
920-3 920-9
920-8
920-10
920-11
DT01 901 920-2 920-1 920-12
903 902 908 DT02

920-13

920
904
907 919
915S 918
909 911 911S 912
911S 913 921
905
917S
913S 919
906
916S 917S 918
910 919S 916C
911S
916
913S
915

817 915S
915S 917
914S 916S
913S
930S
732 916A
870
952S 915
870-1 727
870-2 914
929S 928S 913

732
930S 928S 948S

727 945S

943S XW76
947S
939S
938S 944S 951S
943S-1
946S 951S
931S 915S 950D
935S 914S 941S
933S 942S
932S 911S 913S
934S 936S
931S-2 937S
931S-1

33
9.2 单针中座及下倒缝机构 (JK-6691-X)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
DT01 155419001 定刀 Fixed knief 1
DT02 1554S10001 定刀螺钉 Screw 2
727 155024010 滚针轴承 Needle bearing 2
732 155023003 油棉垫 Oil cotton pad 2
817 C01040 孔用挡圈 28 Retaining ring 28 1
870 B94049 轴承6001-2RZ Bearing6001-2RZ 1
870-1 155208007 定环 Ring 1
870-2 C01083 内六角凹端紧定螺钉M4×5 Screw pan M4×5 2
901 15521500200 单针短线头针板 Single needle short lined plate 1
902 155028002 垫片 Washer 2
903 C01132 内六角圆柱头螺钉M5×12 Screw pan M5×12 2
904 1550S11015 一字圆柱头螺丝 Screw pan 1
905 C0194 内六角圆柱头螺钉M6×16 Screw pan M6×16 2
906 155028002 垫片 Washer 2
907 155026005 调整销 Adjusting pin 1
908 C0193 开槽沉头螺钉M4×8 Screw pan M4×8 2
909 C01091 内六角凹端紧定螺钉M4×10Screw pan M4×10 1
910 155211004 压棒盖 Pressure bar cover 1
911 155201027 短线头单针中座 Single needle short lined bevel 1
912 155025006 中座小齿轮 Bevel gear 1
913 1550S14001 螺钉M6×0.75×6 Screw M6×0.75×6 4
914 155025007 中座小齿轮 Bevel gear 1
915 C01083 内六角凹端紧定螺钉M4×6 Screw pan M4×6 2
916 155203010 套管 Casing 1
916A 155003009 下套管 Running casing 1
916C 155224015 滚针轴承 Needle bearing 1
917 155002005 中座轴 Shaft 1
918 C01085 内六角凹端紧定螺钉M5×4 Screw pan M5×4 4
919 155009009 轴连接器 Shaft connector 2
920 15522500800 单针送金组件 Single needle feeding component 1
921 155011005 塑料接头 Plastic connector 1
911S C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 7
913S 155012014 C型扣环 C-shaped buckle 4
914S 155228006 调整垫片 Washer 2
915S 155024012 轴承608ZZ Bearing 608ZZ 4
916S 155002006 培林轴 Shaft 2
917S 155225006 锥形齿轮 Bevel gear 2
919S 155225007 锥形齿轮 Bevel gear 1
928S 155224016 单向培林座 NA/SK One-way bearing holder NA/SK 2
929S 155205007 万向连杆A Universal joint A 1
930S C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 2
931S 155201024 倒针座 Holder of backstitch 1
931S-1 C01145 内六角圆柱头螺钉M6×20 Screw pan M6×20 2
931S-2 C01020 平垫圈M6 Flat Washer M6 2
932S C0177 内六角平端紧定螺钉M4×16Screw pan M4×16 1
933S C01070 六角螺母M4 Nut M4 1
934S C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 1
935S 155226011 滑动销 Sliding pin 1
936S C01134 内六角圆柱头螺钉M4×8 Screw pan M4×8 2
937S 155212039 滑块限位座 Limited seat of slider 1
938S 155226012 调节销 Adjustig pin 1
939S 155227017 压簧 Compression spring 2
941S C01022 平垫圈M4 Flat Washer M4 2
942S C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 2

34
9.2 单针中座及下倒缝机构 (JK-6691-X)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM

901-3
901-2
920-7
920-6
920-5
901-1 920-4
920-3 920-9
920-8
920-10
920-11
DT01 901 920-2 920-1 920-12
903 902 908 DT02

920-13

920
904
907 919
915S 918
909 911 911S 912
911S 913 921
905
917S
913S 919
906
916S 917S 918
910 919S 916C
911S
916
913S
915

817 915S
915S 917
914S 916S
913S
930S
732 916A
870
952S 915
870-1 727
870-2 914
929S 928S 913

732
930S 928S 948S

727 945S

943S XW76
947S
939S
938S 944S 951S
943S-1
946S 951S
931S 915S 950D
935S 914S 941S
933S 942S
932S 911S 913S
934S 936S
931S-2 937S
931S-1

35
9.2 单针中座及下倒缝机构 (JK-6691-X)
SINGLE NEEDLE CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
943S 155209017 倒针滑块 Slider of backstitch 1
943S-1 155211007 滑套 Sliding sleeve 1
944S 155209006 顶杆挡块 Baffle plate of ejection pin 1
945S C01142 内六角圆柱头螺钉M3×8 Screw pan M3×8 2
946S 155220001 螺钉 Screw 1
947S 155212040 顶杆 Ejection pin 1
948S 15523000300 下送金倒针电磁阀 Solenoid valve for backstitch 1
950D 155212041 下倒针电磁阀座 Solenoid valve seat 1
951S C01137 内六角圆柱头螺钉M5×8 Screw pan M5×8 3
952S 155205008 万向连杆B Universal joint B 1
×W76 155227016 锥形弹簧 Conical spring 1

36
10.1 双针左边座及中座机构
DOUBLE NEEDLE LEFT SIDE BRACKET & CENTRAL BRACKET M ECHANISM

921S
921S-3
810 844
921S-2A/小孔SMALL
811 845 921S-2B/大孔LARGE
802 823 824 846
921S-1
847
804
908 922S
902S-1
925S
902S 908
904S 841-1

905S 843-1
826
843-3
906S 905 926S
822 821 924S
843-5
843-2 906
905 927S
843 923S
822
805 907S 906 821

843-1A 839
838 830
829
836
831
906S 816
870 833 832
808 870-1
840
869
806 817 837
808 868 870-2 814

834
807 815 835

869
841
813 841A
903S 814 812 842

815
802-2
801 802-3
802-1
908S
918S 802-4
901S 802
850 909S 802-6
901S 802-5
917S 910S
913S
910S-1 802-7
805S 915S
917S 850 851 802-8
914S 915S 919S 802-10 802-9
913S 916S

916S-1

37
10.1 双针左边座及中座机构 (JK-6692)
DOUBLE NEEDLE LEFT SIDE BRACKET & CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
801 1550S11014 螺丝 M5×0.8×20 Screw pan M5×0.8×20 1
802 15521800100 旋梭组件 Hook asm 1
804 155209013 大釜护盖 Cauldron fender 1
805S 5530200100 釜轴(双针组件） Shaft 1
807 155228002 轴承垫片 Bearing gasket 1
810 15522100200 油管组件 Tubing components 1
811 1550S11013 开槽圆柱头螺钉M4×6 Screw pan M4×6 1
812 1550S14001 螺钉M6×6 Screw M6×6 2
813 155203008 下套管 Running casing 1
814 155229001 卡簧 Circlip 2
815 155203009 釜轴套管 Axe shaft casing 2
816 155223001 油棉垫 Oil cotton pad 1
817 C01040 孔用挡圈M28 Circlips for hole 1
821 155026003 调整销 Adjustig pin 2
822 C01093 内六角凹端紧定螺钉M4×8 Screw pan M4×8 2
823 1552S11001 开槽圆柱头螺钉 Screw 1
824 155212028 弹簧板 Spring plate 1
826 155222001 橡皮垫 Rubber mat 1
829 155226008 调节销 Adjustig pin 1
830 1552S11002 螺钉 Screw 1
831 155219001 定刀 Fixed knife 1
832 155212029 弹片 Shrapnel 1
833 1552S11003 螺钉 Screw 1
836 C01161 内六角圆柱头螺钉M4×25 Screw pan M4×25 1
838 155219002 动刀 Moving knife 1
839 C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 1
840 C01147 内六角圆柱头螺钉M4×12 Screw pan M4×12 1
841A 155201026 刀座（组件） Tool holder (assembly) 1
843 15521203100 大釜盖组件 Large kettle cover assembly 1
843-1A C01266 内六角平圆头螺钉M4×8 Screw pan M4×8 2
844 155202015 牛角 Rotating hook opener 1
845 C01147 内六角圆柱头螺钉M4×12 Screw pan M4×12 1
846 C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 1
847 155209014 牛角固定座 Rotating hook opener bracket 1
850 1550S14001 内六角无头螺丝M6×0.75×6 Screw pan M6×0.75×6 6
851 155025004 小齿轮 Bevel gear(samll) 1
868 155224013 平面轴承 Plane bearing 1
869 155224014 滚针轴承 Needle bearing 2
870 B94049 轴承 6001-2RZ Bearing 6001-2RZ 1
870-1 155208007 定环 Stationary ring 1
870-2 C01083 内六角凹端紧定螺钉M4×5 Screw pan M4×5 2
901S C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 4
902S 155225009 送料平面齿轮 Plane gear of feeding 2
902S-1 1550S20002 内六角凹端紧定螺钉 Screw 1
905 C0194 内六角圆柱头螺钉M6×16 Screw pan M6×16 2
906 155028002 垫片 Washer 2
908 C0193 开槽沉头螺钉M4×8 Screw pan M4×8 2
908S 155228007 调整垫片 Adjusting washer 1
909S 155225010 送料大齿轮 Bevel gear(large) 1
910S 155228005 调整垫片 Adjusting washer 1
910S-1 155228008 垫片 Washer 2
913S 155012014 C型扣环 C-shaped buckle 2
914S 155228006 调整垫片 Adjusting washer 1
915S 155024012 轴承608ZZ Bearing 608ZZ 2

38
10.1 双针左边座及中座机构
DOUBLE NEEDLE LEFT SIDE BRACKET & CENTRAL BRACKET M ECHANISM

921S
921S-3
810 844
921S-2A/小孔SMALL
811 845 921S-2B/大孔LARGE
802 823 824 846
921S-1
847
804
908 922S
902S-1
925S
902S 908
904S 841-1

905S 843-1
826
843-3
906S 905 926S
822 821 924S
843-5
843-2 906
905 927S
843 923S
822
805 907S 906 821

843-1A 839
838 830
829
836
831
906S 816
870 833 832
808 870-1
840
869
806 817 837
808 868 870-2 814

834
807 815 835

869
841
813 841A
903S 814 812 842

815
802-2
801 802-3
802-1
908S
918S 802-4
901S 802
850 909S 802-6
901S 802-5
917S 910S
913S
910S-1 802-7
805S 915S
917S 850 851 802-8
914S 915S 919S 802-10 802-9
913S 916S

916S-1

39
10.1 双针左边座及中座机构 (JK-6692)
DOUBLE NEEDLE LEFT SIDE BRACKET & CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
916S 155002006 轴承轴 Bearing shaft 1
916S-1 1550S11012 螺钉 M4×0.7×8 Screw pan M4×0.7×8 1
917S 155225006 锥形齿轮 Bevel gear 2
918S 155225011 送料齿轮 Feeding gear 1
921S 5531500100 双针针板组件 Throat plate 1
922S 1550S11014 螺丝 M4×0.7×10 Screw pan M4×0.7×10 2
923S 1550S11015 螺丝 M4×8 Screw pan M4×8 4
924S 55301001 双针中座 Support plate 1
925S 155225012 送料齿轮 Feeding gear 1
926S 155209021 固定板 Thrust collar 1
927S 5530100200 双针左边座 Side bracket(left) 1

40
10.2 细柱中座机构 （JK-6681）
CENTRAL BRACKET MECHANISM

LZ14

LZ11 LZ15
LZ12 LZ13
LZ36
LZ10 LZ24-1
LZ37
LZ21
LZ09 LZ09-3
LZ09-1 LZ22 LZ38
LZ08 LZ25
LZ146 LZ24 LZ23 LZ41-1
LZ07 LZ02 LZ130 LZ41-2
LZ09-2 LZ144 LZ141
LZ06 LZ143
LZ18 LZ131
LZ05
LZ04 LZ17
LZ05
LZ19
LZ03
LZ31 LZ25
LZ01 LZ29
LZ40
LZ32 LZ33 LZ30

LZ109 LZ34
LZ35
LZ41

LZ108 LZ41-2
LZ42
LZ107
LZ106 LZ42-1
LZ105 LZ88 LZ41A
LZ151
LZ76 LZ83 LZ89
LZ155 LZ77 LZ85
LZ150 LZ86 DT919-2
LZ165
LZ152 LZ78 DT919
LZ153 LZ84 LZ87
LZ154 DT919-1
LZ153 LZ80
LZ71
LZ152 LZ102
LZ156 LZ81 LZ74
LZ151
LZ73
LZ158 LZ72
LZ151
LZ70
LZ71
LZ79 LZ133
LZ78
LZ77 LZ159
LZ75 LZ164
LZ165 LZ132 LZ120
LZ167
LZ76

LZ68
LZ78
LZ75-1

LZ69

41
10.2 细柱中座机构零件明细 （JK-6681）
CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
LZ01 1554S10001 定刀螺钉 Screw 2
LZ02 155412001 夹线弹片 Clipping shrapnel 1
LZ03 155419001 定刀 Fixed knief 1
LZ04 C01103 内六角沉头螺钉M4×8 Screw pan M4×8 2
LZ05 C01102 内六角沉头螺钉M3×6 Screw pan M3×6 3
LZ06 15541500100 针板座 Needle plate holder 1
LZ07 155415001 针板片 Needle plate 1
LZ08 1554S10002 针板螺钉 Screw 1
LZ09 15542500100 下送金组件 Under feeding component(asm) 1
LZ10 155425004 送金销 Pin 1
LZ11 155412002 大釜盖 Large kettle cove 1
LZ12 C01048 圆柱销3×20 Cylindrical pin3×20 1
LZ13 155402001 下送金小齿轮 Feeding component bevel gear(small) 1
LZ14 155418001 梭仔子 Shuttle 1
LZ15 15541800100 旋梭 Hook 1
LZ18 155408001 送料齿轮导向套 Feeding gear guide sleeve 1
LZ19 155409001 送料齿轮调整套 Feeding gear adjusting sleeve 1
LZ21 155409002 牛角座 Rotating hook opener bracket 1
LZ22 155402002 牛角 Rotating hook opener 1
LZ23 1554S10004 牛角螺钉 Screw 1
LZ24 155426001 牛角座销 Rotating hook opener bracket pin 1
LZ24-1 1554S10005 牛角销螺丝 Screw 1
LZ28 C01093 内六角凹端紧定螺钉M4×6 Screw pan M4×6 2
LZ29 155426002 调整销 Adjustig pin 1
LZ30 155426003 调整销 Adjustig pin 1
LZ31 155428001 针板调整垫片 Adjustig washer 1
LZ32 1554S10003 定位螺钉 Screw pan 2
LZ33 C01093 内六角凹端紧定螺钉M4×6 Screw pan M4×6 1
LZ34 C0194 内六角圆柱头螺钉M6×16 Screw pan M6×16 4
LZ35 155428002 垫片 Washer 4
LZ36 155405001 牛角摆杆 Rotating hook opener pendulum 1
LZ37 155426004 牛角摆杆销 Rotating hook opener swing pin 1
LZ38 155419002 动刀 Movable knife 1
LZ40 C01227 内六角圆柱头螺钉M3×4 Screw pan M3×4 1
LZ41-1 155428004 平垫圈 Flat Washer 1
LZ41A 15540200100 釜轴套管（组件） Axe shaft casing（asm） 1
LZ42 155403001 釜轴大套管 Axe shaft large casing 1
LZ42-1 155424001 滚针轴承 Needle bearing 1
LZ68 155425005 大齿轮 Bevel gear(large) 1
LZ69 155202016 万向连接轴 Universal connecting shaft 1
LZ70 155408002 锁圈 Lock ring 1
LZ71 C01092 内六角凹端紧定螺钉M4×4 Screw pan M4×4 4
LZ72 155425006 送料大齿轮 Bevel gear(large) 1
LZ73 B94024 HK0709滚针轴承 HK0709 needle bearing 1
LZ74 155425007 小齿轮 Bevel gear(small) 1
LZ75 155401001 轴承座 Bearing holder 1
LZ75-1 C01145 内六角圆柱头螺钉 Screw pan M4×8 2
LZ76 C01040 孔用挡圈 Circlips for hole 2
LZ77 B94049 轴承6001-2RZ Bearing 6001-2RZ 2
LZ78 155408003 锁圈 Lock ring 3
LZ79 155401002 剪线凸轮 Trimming cam 1
LZ80 155408005 定环 Ring 1
LZ81 155425008 下送料大齿轮 Bevel gear(large) 1

42
10.2 细柱中座机构 （JK-6681）
CENTRAL BRACKET MECHANISM

LZ14

LZ11 LZ15
LZ12 LZ13
LZ36
LZ10 LZ24-1
LZ37
LZ21
LZ09 LZ09-3
LZ09-1 LZ22 LZ38
LZ08 LZ25
LZ146 LZ24 LZ23 LZ41-1
LZ07 LZ02 LZ130 LZ41-2
LZ09-2 LZ144 LZ141
LZ06 LZ143
LZ18 LZ131
LZ05
LZ04 LZ17
LZ05
LZ19
LZ03
LZ31 LZ25
LZ01 LZ29
LZ40
LZ32 LZ33 LZ30

LZ109 LZ34
LZ35
LZ41

LZ108 LZ41-2
LZ42
LZ107
LZ106 LZ42-1
LZ105 LZ88 LZ41A
LZ151
LZ76 LZ83 LZ89
LZ155 LZ77 LZ85
LZ150 LZ86 DT919-2
LZ165
LZ152 LZ78 DT919
LZ153 LZ84 LZ87
LZ154 DT919-1
LZ153 LZ80
LZ71
LZ152 LZ102
LZ156 LZ81 LZ74
LZ151
LZ73
LZ158 LZ72
LZ151
LZ70
LZ71
LZ79 LZ133
LZ78
LZ77 LZ159
LZ75 LZ164
LZ165 LZ132 LZ120
LZ167
LZ76

LZ68
LZ78
LZ75-1

LZ69

43
10.2 细柱中座机构零件明细 （JK-6681）
CENTRAL BRACKET MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
LZ84 B94063 轴承6800-ZZ Bearing6800-ZZ 1
LZ85 155402003 下送料齿轮轴 Feed rocker shaft 1
LZ86 155409003 送料轴下衬套 Feeding shaft lower bushing 1
LZ87 155425009 下送料小齿轮 Bevel gear(small) 1
LZ88 155409004 釜轴下衬套 Axe shaft lower bushing 1
LZ89 155408006 釜轴下锁圈 Axe shaft locking ring 1
LZ102 1550S14003 内六角平端无头螺钉 Screw pan 2
LZ105 C01226 内六角圆柱头螺钉M3×12 Screw pan M3×12 1
LZ106 C01125 内六角圆柱头螺钉M6×12 Screw pan M6×12 2
LZ107 C01045 销φ 5×16 Pin φ 5×16 2
LZ108 155401003 中座后固定座 Middle seat fixed block 1
LZ109 155401004 中座 Middle seat 1
LZ120 15542100100 油管组件 Tubing components 1
LZ130 155401005 夹线弹片座 Clipping shrapnel seat 1
LZ131 155401006 固定块 Fixed block 1
LZ132 C01142 内六角圆柱头螺钉 Screw pan 2
LZ133 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 2
LZ141 C01102 内六角沉头螺钉M3×6 Screw pan M3×6 1
LZ143 1554S17001 螺钉 Screw 1
LZ144 C01140 内六角圆柱头螺钉M2.5×5 Screw pan M2.5×5 1
LZ146 1554S13001 螺钉M2 Screw M2 1
LZ150 155425010 送料齿轮 Feeding gear 1
LZ151 1550S14001 螺钉M6×0.75×6 Screw M6×0.75×6 8
LZ152 155012014 C型扣环 C-Retaining ring 2
LZ153 155024012 轴承 Bearing 2
LZ154 155425011 锥形齿轮 Bevel gear 2
LZ155 C01086 内六角凹端紧定螺钉 Screw pan 4
LZ156 155402004 培林轴 Shaft 1
LZ158 155428003 调整垫片 Washer 1
LZ159 155412003 油管座 Tubing seat 1
LZ164 C01212 内六角凹端紧定螺钉M6×6 Screw pan M6×6 2
LZ165 C01083 内六角凹端紧定螺钉M4×5 Screw pan M4×5 4
LZ167 1550S14001 螺钉M6×0.75×6 Screw M6×0.75×6 4
DT919 155405002 刀轴摆杆 Pendulum of knife shaft 1
DT919-1 C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 2
DT919-2 C01169 内六角圆柱头螺钉M3×6 Screw pan M3×6 1

44
11 倒针机构 (JK-6692、JK-6691-X、JK-6681)
REVERSE STITCHING & THREAD TRIMMING MECHANISM

954S

956S

955S

917S 961S
957S
919S
911S 958S
960S 959S
913S
915S

916S
953S

952S

930S
727 732
929S
929S 928S
单针
732 SINGLE NEEDLE
930S
928S

948S
727
943S 945S

XW76
947S
939S
938S 944S
943S-1
946S

931S 915S 951S

914S 951S
935S
933S 913S 950D
911S 936S
932S 931S-2 941S
934S 931S-1 937S 942S

45
11 倒针机构 (JK-6692、JK-6691-X、JK-6681)
REVERSE STITCHING & THREAD TRIMMING MECHANISM
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
727 155024010 滚针轴承 Needle bearing 2
732 155023003 油棉垫 Oil cotton pad 2
911S C01086 内六角凹端紧定螺钉M5×6 Screw pan M5×6 3
913S 155012014 C型扣环 C-shaped buckle 2
915S 155024012 轴承608ZZ Bearing 608ZZ 2
916S 155002006 培林轴 Shaft 1
919S 155225007 锥形齿轮 Bevel gear 1
928S 155224016 单向培林座 NA/SK One-way bearing holder NA/SK 2
929S 155205007 万向连杆A Universal connecting rod A 1
930S C01134 内六角圆柱头螺钉M4×10 Screw pan M4×10 1
931S 155201024 倒针座 Backstitch seat 1
931S-1 C01145 内六角圆柱头螺钉M6×20 Screw pan M6×20 2
931S-2 C01020 平垫圈M6 Flat washer M6 2
932S C0177 内六角平端紧定螺钉M4×16 Screw pan M4×16 1
933S C01074 六角螺母M4 Nut M4 1
934S C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 1
935S 155226011 滑动销 Sliding pin 1
936S C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 2
937S 155212039 滑块限位座 Limited seat of slider 1
938S 155226012 调节销 Adjustig pin 1
939S 155227017 压簧 Compression spring 2
940S 1550S20001 开槽无头轴位螺钉 Screw 1
941S C01022 平垫圈M4 Flat washer M4 2
942S C01139 内六角圆柱头螺钉M4×8 Screw pan M4×8 2
943S 155209017 倒针滑块 Slider of backstitch 1
943S-1 155211007 滑套 Sliding sleeve 1
944S 155209006 顶杆挡块 Baffle plate of ejection pin 1
945S C01142 内六角圆柱头螺钉M3×8 Screw pan M3×8 2
946S 155220001 螺钉 Screw 1
947S 155212040 顶杆 Ejection pin 1
948S 15523000300 下送金倒针电磁阀 Solenoid valve for backstitch 1
950C 155212037 下倒针电磁阀座 Solenoid valve seatofbackstitch 1
951S C01137 内六角圆柱头螺钉M5×10 Screw pan M5×10 3
952S 155211011 油镜 Oil mirror 1
953S C0208 O型圈32×1 O-ring 32×1 1
954S 155221003 油管 Tubing 1
955S 155217002 开槽沉头螺钉M4×16 Screw pan M4×16 1
956S 155212033 线卡 Ply-yard drill 1
957S 155211010 油管护架 Tubing guard 1
958S C01023 平垫圈 Flat washer 1
959S C01147 内六角圆柱头螺钉M4×12 Screw pan M4×12 1
960S 155236001 油管接头 The tubing connector 1
961S 155221001 油管 Tubing 1
×W76 155227016 锥形弹簧 Conical spring 1

46
12 随机附件 ACCESSORIES

F003B F030 F004 F028

F003B-04
F003B-03 F003B-08

F003B-06
F003B-02
F005
F003B-05 F003B-09
F003B-10
F003B-01 F003B-07
F007
F006
F027

F011 F001
F012 INDPx5#16
F009 F010
F002 F013

F022
F022 F016 F017
F017-04
F014
F017-03
F016 F014
F017-06

F017-05

F017-12 F017-11
F017-08

F025 F008
F017-09

F024 F017-10

F031 F019A-05
F019A-06
F023 F019A-11
F019A-04 F019A-07
F019A-02 F019A-03
F019A-01
F019A-13 F019A-12

F019A-10
F026
F019A-09

F019A
F019A-08-1
根据客户要求配置
F019A-08-2
According to customer
F019A-08-3
requirments

47
12 随机附件
ACCESSORIES
序号 件号 数量
零部件名称 Name of parts 备注
N0. Part No. Amt.
F001 155031001 内六角扳手(2mm) Allen key (2mm) 1
155031002 内六角扳手(2.5mm) Allen key (2.5mm) 1
155031003 内六角扳手(3mm) Allen key (3mm) 1
155031004 内六角扳(4mm) Allen key (4mm) 1
155031005 内六角扳手(5mm) Allen key (5mm) 1
F002 155231002 横嘴油壶 Horizontal mouth oil pot 1
F003B-01 155231003 线架盘 Thread stand rack 1
F003B-02 155231004 线架 Thread stand 1
F003B-03 155231005 线架螺钉 Screw of thread stand 2
F003B-04 155231006 尼龙挡圈 Nylon retaining ring 2
F003B-05 C01212 内六角凹端紧定螺钉M6×6 Screw pan M6×6 2
F003B-06 155231007 支撑杆 Stand rod 2
F003B-07 C01074 六角螺母M5 Nut M5 2
F003B-08 155231008 支撑芯 Support core 4
F003B-09 平垫圈M5 Washers M5 2
F003B-10 C01034 弹簧垫圈M5 Spring washer M5 2
F004 155231009 油盘 Oil pan 1
F005 155231010 工具盒 Tool box 1
F006 155231011 梭仔子 Shuttle 3
F007 C0192 圆钢钉8分 Round steel nail 0.05KG
F009 155031006 螺丝起子（小） Screwdriver (small) 1
F010 155031007 螺丝起子（中） Screwdriver (middle) 1
F011 155031008 螺丝起子（大） Screwdriver (big) 1
F012 15503100900 枕木(组件） Sleeper (component) 1
F014 155031011 橡胶垫 Rubber mat 2
F016 155231012 后纽扣橡胶垫 Rubber mat of rear button 2
F017 155231013 脚弓组 Ankle arch group 1
F019A 155231014 靠边组件 Edge assembly 1
F022 155231015 橡胶垫 Rubber mat 2
F027 155031013 后纽扣 Rear button 2
F030 155231001 附件纸箱 Accessory carton 1
155231018 附件装箱盒 Accessory box 1
D03005 标牌铆钉/不锈钢 Sign rivet / stainless steel 6
155231024 机头罩 Nose covering 1
155231029 木螺丝 Wood screw 4
E98054 车针 INDPX5#16 Needle INDPX5#16 5
155231023 号码牌 Identification tag 1
155231020 合格证 Certificate 1
155231021 罗拉车纸箱 Roller carton 1
155231022 机身泡沫组件 Foam for machine 1
E04034 PE袋 PE bag 1
155231029 木螺丝5×25 Wood screw 5×25 4
155231030 说明书 Instructions 1

48
13 电器连接图 ELECTRICITY ELEMENTS FIG

EW01
X2.1

138
抬压脚 X2.2

X2.3

638 X3.1
剪线 松线
418
948S X3.2
下倒缝

716
上倒缝 X4

X8
330A
针摆 X8.1
969B
X8.2

151
512-3

49