D2008type

Electronic Weighing Indicator

User Manual

Version: August. 2013

●Please read this manual carefully before using

●Please keep this manual properly for reference

a
 Index

1 Technical parameter .........................................................................................................................................1

2 Operation instructions ......................................................................................................................................2
2.1 Start-up and automatic start-up zero setting .........................................................................................2
2.2 Manual zeto setting ...............................................................................................................................2
2.3 Tare .......................................................................................................................................................2
2.4 Zero Tare ...............................................................................................................................................2
2.5 Date and time check and setting .........................................................................................................2
3 Store and print weighing record .......................................................................................................................2
3.1 Store weighing record ...........................................................................................................................2
3.2. Input method of tare storage ................................................................................................................3
3.3. Printing of weighing record .................................................................................................................3
3.4. Statistical form printing .......................................................................................................................4
3.5 Inquiry weighing record ........................................................................................................................5
3.6 Delete weighing record .........................................................................................................................7
3.7 Delete method of tare storage ...............................................................................................................7
3.8．Inquirying print .....................................................................................................................................7
4 Information tips..............................................................................................................................................7
Appendix A：the example of printing operation ..................................................................................................8
Appendix B：Examples of breakdown ...............................................................................................................10

▲The connection between load cell and indicator must be reliable, load cell's shielding wire must be reliable
grounding. Connection inserting or pull out is not allow when indicator is under the state of power, prevent
electrostatic damage the indicator or the load cell .
▲ Indicator and load cell are static sensitive equipment,anti-static measure must be taken when using, the
welding operation or other high voltage operation on the weighing pad is prohibited , at the thunderstorm
season, the reliable avoid measures must be implemented to prevent the lightning strike the load cell and the
indicator, ensure the security of the operating personne and running of the weighing equipment and related
equipment.
▲ Can not use in the area of flammable gas or flammable vapor,also can not use in the tank weighing system
with pressure.
▲Indicator and load cell must be away from the field with strong electric and magnet,and be away from strong
corresive substance ,be away from inflammable and explosive materials.
▲Using strong solvents(such as benzene,nitro-class oil)to clean the housing is prohibited.
▲Can not inject the liquid or other conductive particle into indicator to prevent to damage and electronic
shock.

b
1 Technical parameter

1.Type D2008 (H)(AC)、

D2008(HP)(AC)、
D2008(HP1)(AC)
2.Digital load cell interface:
Communication mode RS485
Signal transmission distance 30M when connected with 12 load cells,pls contact us if you need
further
Transmission baud rate 9600、19200bps
Excitation power DC12~14.8V
Digital interface ability ≤16 digital load cells
3.Display： 7 digits of LED，7 digits of status symbols
4. Keyboard
Number Keys 0~9
Function keys 24 pcs（10 of 24 are combined with Number keys）
5.Clock
display year, month, date, hour, minute and second, leap year and leap month automatically.
6.Scoreboard display interface (electric isolated with load cell interface)
transmission mode: current loop and RS232
Transmission baud rate: 600bps
7.Serial communication interface (electric isolated with load cell interface)
transmission mode: RS232
Baud rate: Options of 600/1200/2400/4800/9600/19200
8.Printing interface (electric isolated with load cell interface)
With standard parallel printing interface, which can be connected with the wide line
printers , such as ESPON LQ-300K ＋ Ⅱ 、 ESPON LQ-300K 、 ESPON
LQ-300K ,ESPON LQ-680K 、ESPON LQ-730K 、ESPON LQ-1600K（＋）、
KX-P1131、KX-P1121、DS-300
9.Data storage
can store 1,000 groups of vehicle numbers and tare weight, 1500 groups new
weighing records, 300 groups uncompleted weighing records, 6 groups overload
records.
10. Operating environment
Power input : AC 220V 50HZ
DC 12V
Operating temperature: 0℃ ~ 40℃
Storage temperature : -25℃ ~ 55℃
Relative humidity : ≤85%RH

1
2 Operation instructions
2.1 Start-up and automatic start-up zero setting
Connect to power supply and turn on the power switch. The indicator begins self-checking. After successful
self-checking, the indicator enters the weighing status.
During the start-up, if the zero point is off-set but still in the range preset, the indicator will automatically.
Refer to manual of calibration for the range of start-up zero setting.

2.2 Manual zero setting

Zero setting function is only valid when stability light is on.
The key【ZERO】will not work when the off-set is over the range of manual zero setting. Refer to manual of
calibration for the range of start-up zero setting.
Press the key【ZERO】and the indicator will return to zero and the zero light will be on.

2.3 Tare
D20 offers 2 types of taring.
Under the weighing status.
A: Common taring:
When the weight data is over 0 and stable, press the key【Tare】and the value displayed will be deducted
as tare weight. At this time, the indicator will display value of net weight. Tare indicating light will be on and
gross indication light will be off.
B: Preset the tare weight
Press the key 【 Preset 】 and the indicator will display 【 P***** 】 . Then input the tare weight, press
【ENTER】and indicator will display original tare weight.

2.4 Zero tare

There are 2 modes:
A. Under the status of taring, press【ZERO】to clear the tare weight and the tare indicating light will be off.
This operation will be limited by Pn parameter
B. Press 【Preset】,set the tare weight is 0.

2.5 Date and time check and setting

steps operation display explain
1 press【CLOCK】 d12.05.13 Display the date
press d12.05.13 Modify the date
2
【number key】
press d12.05.15 Enter current date
3
【120515】
4 press【enter】 d09.08.15 Show current date
press【enter】 t12.53.48 Mark: if open the timing function, can not modify
5
the date
press t12.53.30 Show the time
6
【number key】
press t12.53.45 Enter correct time
7
【125345】
press t12.53.45 Show current time
8
【enter 】
press【weigh】 Weighing
9
interface

3. The save and print of weigh result

3.1．The save of weigh record
2
（1）This indicator asked the car No. is 5 digit(1~99999),Art.No.is 3 digit（0~200）,
(2) It can save 1500 group weigh records mostly, after full, will delete the earliest group result.
(3) There are 3 ways to save the data:
① weight directly(press key【save1】)save: When you make one weight, it can make the data as one
group to save and print
②First preset or call the known tare weight when weighing, (press key [ save1]) storage one time to
constitute a complete set of records; or weighing cargo vehicles is only a cargo (the car number is00000 or do
no use the number), (press [save 2] or [Save 1] key) one time and storage constitute a complete set of
records.
③Weighing twice save(press [Save 2] key): the first empty (press the [Save 2] key) storage ,then full
of cars (press 【 save 2】 key) storage, or the first full car ( press 【save 2】 key) save and then empty
(press [save 2] key) storage, which means that after two (press 【 save 2 】 key) save will constitute a
complete set of records. Press [Save 2] key storage, in order to automatically identify the distinction between
above ②, ③ two kinds of storage, especially for the following agreements:
▲! The vehicle's license plate number must be any number between 00001 and 99999. That is to say 00000
can not be used as a real vehicle license plate number. If the license plate number is set to 00000 when you
come to weighing a vehicle loading a cargo. At this point the indicator will be stored in accordance with ②
the way.
▲! If the sign of the indicator peeled is lighting, tare known storage time will constitute a complete record.
▲! If the license plate number is set to 00000 other than any 5-digit, peeled and indicator identifier does not
shine (is Gross state) must be twice the storage operation can constitute a complete record.
▲! If you do not choose to use the license plate number, it is mean that do not weigh vehicles, one storage
will constitute a complete record.
(4) Save operation method
Please check the appendix A detail for examples
(5) When the data is unstable, or gross weight ≤ 0 or gross weight ≤ net weight or does not meet the return
to zero conditions, can not be stored, otherwise the indicator display [ Err 19] in order to prompt the operator
(6) About auto save and print
① Please check the print setting chapter for the setting of Auto save print
② when auto save print, do not have 2 save ways.
③ when auto save, the saved car No., cargo No. is the setted well ones before saving
④ There are 3 conditions for the auto save tare weight value:
a) When the peeled mark of indicator is lighting, store the group record as the tare weigh value
b) When the peeled mark of indicator is not lighting, automatically find the tare weigh value below
this car No. in ram, save this tare weigh value to this group record.
c) When the peeled mark of indicator is not lighting, and there is no tare weight value in ram, will
save in the group record as the cargo form.
3.2．The input method of tare weight save
The indicator can store 1500 tare values of vehicle number. There are 3 methods to input.
1. Input tare with number key: (*: original value)
Step Operation Display Explanation
1 Press【V.N】 Under weighing status
o ***** Input vehicle number. For example: 35790.
Input vehicle o 35790
2
number
Press【ENTER】
P ***** Input tare weight. For example: 1000(kg).
3 Input tare value P 01000
Press【ENTER】
4 Return to weighing status End
Mark:step 2:Press【CLEAN】,if has this vehicle number,when delate,will show”PASS”
2. Save tare by weighing:
Under the weighing status, place the empty vehicle on the scale. Wait until the scale is stable, press【V.N】
and input the vehicle number, and then press【PRESET】.
3.3 The mothed for Vehicle tare checking and clear
3
step operation display explain
1 press【check】 S-CodE Enter password
2 press【111111】 S- - - - - - fixed password“111111”
3 press【ENTER】 rEAd 00 Choose function number
4 press【6】 rEAd 06 choose 6to check vehicle tare
5 press【ENTER】 PEr *** show store space usage percentage(store
number/1000)
6 press【ENTER】 o ***** show first vehicle number
7 press【ENTER】 P****** show the checked vehicle tare
9 press【ENTER】 o ***** still show first vehicle number
Mark:step 6 and 7:Press【CLEAN】,clear this vehicle tare; Press【←/→】,check the front and back vehicle
tare.
3.4．Print of weighing record
1． Printing parameter must be set correctly before printing. (Refer to the part of printing parameter setting
of technical manual)
2． The storing and printing of the indicator are simultaneous. At the same time when a group of complete
record is stored with【SAVE1】or【SAVE2】, it will be printed out. (If the printing setup is effective,
namely the model of the printer is non-zero and printing while storing is selected)
3． If the weighing record is not printed successfully because of some reason (ex.: printer fault), after the
fault is eliminated, press【REPRINT】and print the record stored currently.
4． In the end of a period of weighing, may press【A.P】to print out the accumulated value.
5． If press【SAVE2】and use the two-time storage (loaded after empty, or empty after loaded), during
the first storing, because the record is not completed, the indicator displays【LoAd】for 1.5 seconds but
does not print. However, if press【REPRINT】at this time, the incomplete record can still be printed out.
The printing result is as below:
① Serial number is 0;
② Gross weight and net weight are all 0;
③ Tare weight is the weight value displayed currently.
3.5 Statistical form printing

Parameter or
Paremeter or Function Type
Function Code
00 General Form
01 Detail Form in Certain Date
02 Detail Form during Certain Period
03 Detail Form for Certain Vehile No.
04 Detail Form for Certain Cargo No.
1. Total detail list Form
Steps Operation Display Explanation
1 Press【Form】 Pb 00 Choose total list form
Press【Enter】 Print Begin printing the form. Back to the weighing
2
status after printing
2.Some day detail list form
Steps Operation Display Explanation
Press【Form】 Pb 00
1
2 Press【01】 Pb 01 press“01”，choose some day detail list form
3 press【ENTER】 d00.00.00 Enter date
4 press【120520】 d12.05.20 For example 2012-05-20
5 Press【Enter】 Print Begin printing the form. Back to the weighing status
4
 after printing
3.Some time detail list form
Steps Operation Display Explanation
Press【Form】 Pb 00
1
2 press【02】 Pb 02 press“02”，choose some time detail list form
3 press【ENTER】 d00.00.00 Enter start date
4 press【40101】 d12.05.20 For example 2012-05-20
5 press【ENTER】 d00.00.00 Enter end date
6 press【40101】 A12.05.20 For example 2012-05-20
Press【Enter】 Print Begin printing the form. Back to the weighing status
7
after printing
4.Vehicle No. detail list form
Steps Operation Display Explanation
1 Press【Form】 Pb 00
2 press【03】 Pb 03 press“03”，choose vehicle NO. detail list form
3 press【ENTER】 o 00000 Enter Vehicle number
4 press【00123】 o 00123 Vehicle number is“00123”
Press【Enter】 Print Begin printing the form. Back to the weighing status
5
after printing
5.Cargo No. detail list form
Steps Operation Display Explanation
Press【Form】 Pb 00
1
2 press【04】 Pb 04 press“04”，choose cargo NO. detail list form
3 press【ENTER】 hn ** Enter cargo number
4 press【123】 hn 123 Cargo number is“123”
Press【Enter】 Print Begin printing the form. Back to the weighing status
5
after printing
3.6．Inquiry and clear weighing record
3.6.1 Press 【Check】to check the memory contents in the indicator by different modes. Operation method
are as follows:
Press 【Check】 under weighing status (If check encrypt is selected, the indicator will display 【S-CodE】to
ask to input the password. After the password is passed) the indicator will display 【rEAd 00】to ask to
enter the inquiry mode.
rEAd 1 Check by Date rEAd 2 Check by Vehicle No.
rEAd 3 Check by Cargo No. rEAd 6 Check/clear vehicle
No.’s tare
rEAd 11 check imperfect rEAd 12 check imperfect
record by date record by vehicle
number
Press 【Enter】after enter the inquiry mode and the indicator will prompt to enter the required conditions for
the inquiry such as date, vehicle no., cargo no., customer no., remarks no. etc. After that it will display the
required records one by one. when check the complete and uncomplete record, the newest record will be
displaied.
3.6.2． Example for Inquiry Operation:
Example：Inquiry according to the date, i.e, inquiry the complete records in certain date
Step Operation Display Explanation
1 Under Weighing Status Enter code

5
 Press【Check】 S-CodE
2 press【111111】 S- - - - - - Fix code“111111”
3 PRESS【ENTER】 rEAd 00 Choose function number
4 press【1】 rEAd 01 choose number 1,check the complete record
as per date
5 PRESS【ENTER】 no 0001 Show first record
6 PRESS【ENTER/↓】 d12.05.31 show first record date
7 PRESS【ENTER/↓】 t09.58.44 show first record date
8 PRESS【ENTER/↓】 o 12345 show first record vehicle number
9 PRESS【ENTER/↓】 hn 003 show first record cargo number
10 PRESS【ENTER/↓】 A001.200 show first record gross weight
11 PRESS【ENTER/↓】 t000.200 show first record tare
12 PRESS【ENTER/↓】 A001.000 show first record net weight
13 PRESS【ENTER/↓】 no 0001 Back to first record
Note:step 5-step 12,if the current weigh record do not have【REPRINT】,it will display【Err 17】,otherwise,
clear the weigh record. If press【←】will check the latest full weigh record, press 【→】will check before
full weigh record.
Step6:if press 【 clean 】 ,if the current weigh record still do not have 【 REPRINT 】 ,it will display 【 Err
17】,otherwise will clean all weigh record for this date.
3.7 Delate operation for weighing record and vehicle number tare
Step Operation Display Explanation
1 press【CLEAN】 S-CodE Enter code
2 press【111111】 S- - - - - - Fix code“111111”
3 press【ENTER】 SurE 0 Choose function number
1.Delate all complete record and uncompleted record
2.Delate all vehicle number tare
3.Delate all uncompleted record
4 press【1】 SurE 1 Choose to delete all complete record and uncompleted
record
5 press【ENTER】 ---- Deleting….
PASS finished, return to【weighing display】

3.8. Inquiry and print

The indicator can print out the record which is being inquiried, the operation is as below: during inquiring and
when displaying any one record , press 【Reprint】 to print out this inquired record. The number is 0.

4. Information tips
4.1 normal information tips
number display Explanation
【 ------- 】 please wait, the inner part of indicator is under calculating,
1
don’t make any operation
2 【 Print 】 the data is connecting between indicator and printer.
3 【 Load 】 the first data storing between the 2 times of weighting
4 【 End 】 Operation end
5 【 PASS】 Setting changed successfully
6 【Lo bAt】 Low power, will power off
7 【 -】 Voltage is under 10.2V,please recharge in time
8 【 SAVE 】 Data saving

4.2.wrong operation information tips:

number display Explanation
1 【Err 03】 overloading warning, must unload all or part of loading.

6
 2 【Err 08】 no record under this condition
【Err 11】 storing space is full with vehicle no., please delete part or all
3
of stored tare
【Err 12】 can not print the form of record by mini printer.or POS
4
【Err 17】 Parameter setting does not meet requirements, please refer to
5
the related parameters input range
【Err 19】 Zero negative weighing or instability cannot print, do not
meet back to zero conditions don't print; Storage of input
parameter not meets the requirement; Discrepancy zeros
6
conditions; Do not conform to the skin condition: unstable
negative; no tare information when check vehicle number

7 【Err 26】 time to power off

8 【Err 27】 The testing time is end
【Err 28】 Print date of the storage of weighing less than has the record
9
date
10 【Err 30】
11 【ECC 01~16】 N load cell’s communication wrong
【ECCP 01~16】 N digital load cell ’ s communication and security is not
12
available
【Err P】 printer connection error, printer error or printer didn't have
13 paper, please add paper or press weighing key to exit

4.3.Other information tips：

number display Explanation
1 【 --S-- 】 start work to zero
2 【S-CodE 】 code”111111”
3 【C-CodE 】 enter calibration code
4 【d-CodE 】 enter trial deadline code

Appendix A: print operation for example:

In printing in the control parameters choose not to input car number, and money order, for in the operation
of the corresponding will print skip steps, use at the same time the current meter car number and money
order memory unit original data storage. If in the storage projects choose not to use car number or money
order, for in the print operation when also can skip the corresponding steps, and do not store and print the
corresponding project (as shown in the technical specifications chapter 6 and 6 Settings).
1. One manual operation preset tare print weighing list
Step Status Operation Display Explanation
Vehicles to Press【preset】 P000.000 Tip input tare weight values
1
weigh in
Input tare If the input [1000] P001.000
2
weight value
Press【enter】 - 1.000 Show the scale gross/net weight value, to
skin FuLiang logo.
Note: at this time to switch to display
3
meter net state (according to the
net/gross 】 can switch over the show
state).
4 Waiting for Press【Save 1】 o ***** Display the original car number. Hint user
7
 stability OR input new car number. Note: if user
storage projects choose not to use the car
Press【Save 2】
number or in print control parameters
choose not to enter in the car number (see
chapter 3 "print parameter Settings" part),
this step is not in the show car number
and suggests the new car number input,
directly to step 6
Input vehicle FOR Press o 00123
5
number 【00123】
Press【enter】 HN *** Display the original cargo no. ask to user
6
enter new cargo number
Input money FOR input【001】 HN 001 Cargo number 001
7
order
8 Press【enter】 PriNt Print weighing list.
Note:when the tare light is on,can go the step 4.do not need operate step1-3 each time.
2.One manual operation print weighing list
Step Status Operation Display Explanation
The goods Press【Save 1】 o ***** Display the original car number. Ask user
1 pounds, for input new vehicle number。
stability
Input vehicle input【00123】 o 00123 Enter vehicle number,such as 00123
2
number
Press【enter】 HN *** Display the original cargo no. ask to user
3
enter new cargo number
Input money FOR input【001】 HN 011
4
order Press【enter】
5 PriNt Print weighing list.
Note: when no this vehicle number tare, indicator will imprint the GW is current value,
tare is 0.
3.two weighing print weighing list (namely first after the first car or empty car heavy
weight after car, here to the former empty car for example)
Step Status Operation Display Explanation
The empty Press【Save 2】 o ***** Display the original vehicle number. ask
vehicle is on user input new number.
1
weighing, for
stability
Input car input【00123】 o 00123 If the new number is the same with
2 number before vehicle number, do not need to
enter new one.
Press【enter】 HN *** Display the original cargo no. ask user
3
input new cargo no.
Input money FOR input【001】 HN 011
4
order
5 Press【enter】 LoAd back to weighing state after 1.5 seconds
Heavy vehicle Press【Save2】 o ***** Display the original car number. ask
is on user input the vehicle number the same
6
weihging, for as "step 2"
stability
Press【enter】 HN *** Display the original car number. ask
7 user input the vehicle number the same
as "step 4"
8 Press【enter】 PriNt Print weighing list

Before use configuration for Auto print weigh list

The detail please check the 《 calibration manual 》 Chapter 6,section 6.,set Quto, Return to zero HL and
8
minimum print weigh L.

Appendix B：Examples of breakdown and statistic form

Breakdown ( total)

No. Date Time Vehicle Cargo G.W. Tare N.W.

No. No. (t) (t) (t)
0001 05 20：06 00001 003 2.003 1.000 1.003
0002 05 20：21 00123 004 1.000 1.000 0.000
0003 05 20：41 00001 010 1.000 0.100 0.900
0004 05 20：44 00001 001 1.000 0.100 0.900
0005 05 20：45 00001 050 1.000 0.100 0.900
0006 05 20：45 00002 06 1.000 0.100 0.900
Total： G.W.： 7.003 t N.W.：
4.603

Applicable model：D2008 型(H、HP、HP1)

D2008 型(D28)
D2008 型(20KB、20KBP、20KBP1)