HT Light duty metal anchors

Economical metal frame anchor

Anchor version Benefits
- Fastening door and window
frames
HT
- No risk of distortion or forces of
(M8-M10)
constraint
- Expansion cone cannot be lost

Base material Load conditions

Autoclaved Fire
Concrete
Solid brick Hollow brick aerated resistance
(non-cracked)
concrete

Approvals / certificates
Description Authority / Laboratory No. / date of issue
Fire test report IBMB, Braunschweig UB 3016/1114-CM / 2006-03-13
Assessment report (fire) warringtonfire WF 327804/A / 2013-07-10

Basic loading data ( for a single anchor)

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Base material as specified in the table
- Non-cracked concrete: fcc ≥ 20 N/mm2
- Minimum base material thickness

Characteristic resistance
Anchor size HT 8 HT 10
NRk [kN] 4,2 5,0
Concrete, fcc=30 N/mm2
VRk [kN] 6,6 7,0
NRk [kN] - 0,3
Aerated concrete PP2a)
VRk [kN] - 0,5
NRk [kN] 1,8 2,6
Solid brick Mz 12
VRk [kN] - 5,0
NRk [kN] 1,8 2,6
Sand-lime solid brick, KS 12
VRk [kN] - 5,0
NRk [kN] - 1,5
Sand-lime hollow brick, KSL
VRk [kN] - 0,5
a) Rotary drilling only.

1 Updated: Dec-17
Recommended loads
Anchor size HT 8 HT 10
NRec [kN] 1,4 1,7
Concrete, fcc=30 N/mm2
VRec [kN] 0,5 0,5
NRec [kN] - 0,1
Aerated concrete PP2a)
VRec [kN] - 0,15
NRec [kN] 0,6 0,8
Solid brick Mz 12
VRec [kN] - 0,5
NRec [kN] 0,6 0,8
Sand-lime solid brick, KS 12
VRec [kN] - 0,5
NRec [kN] - 0,5
Sand-lime hollow brick, KSL
VRec [kN] - 0,15
a) Rotary drilling only.

Materials

Material quality
Part Material
Bolt Steel strength 4.8, zinc plated to 5 µm
Sleeve Steel 02 DIN 17162, sendzimir zinc plated to 20 µm

Setting information

Setting details
Anchor size HT 8 8x72 8x92 8x112 8x132 8x152 8x182
Nominal diameter of drill bit d0 [mm] 8 8 8 8 8 8
Depth of drill hole h1 [mm] 50 50 50 50 50 50
Anchorage depth hnom [mm] 30 30 30 30 30 30
Anchor length L [mm] 72 92 112 132 152 182
Torque moment Tinsta) [Nm] 100 100 100 100 100 100
Minimum base material thickness hmin [mm] 4 4 4 4 4 4
Drill bit TE-CX-8/17 TE-CX-8/22 TE-CX-8/27

Setting details
Anchor size HT 10 10x72 10x92 10x112 10x132 10x152 10x182 10x202
Nominal diameter of drill bit d0 [mm] 10 10 10 10 10 10 10
Depth of drill hole h1 [mm] 50 50 50 50 50 50 50
Anchorage depth hnom [mm] 30 30 30 30 30 30 30
Anchor length L [mm] 72 92 112 132 152 182 202
Torque moment Tinsta) [Nm] 100 100 100 10 10 10 10
Minimum base material thickness hmin [mm] 8/4 8/4 8/4 8/4 8/4 8/4 8/4
TE-C-
Drill bit TE-C-10/17 TE-C-10/22 TE-C-10/27
10/37
a) First value: solid base material, second value: hollow base material.

Updated: Dec-17 2
 min. 50mm

Installation equipment
Anchor size HT 8 HT 10
Rotary hammer TE1-TE16
Other tools hammer, screwdriver

Setting instruction

*For detailed information on installation see instruction for use given with the package of the product.
Setting instruction
1. Drill hole with the drill bit 2. Install anchor 3. Drive screw into anchor

3 Updated: Dec-17
Updated: Dec-17 4