2.
Display1
KT-LCD10YN E-Bike Display User Manual
Hold button to start up and enter display .
Dear customer, please read this manual before you use KT-LCD10YN Display. The manual will guide you use the
instrument correctly to achieve a variety of vehicle control and vehicle status displays.
Functions and Display
Instruments using the structure form of instrument body portion and the operation buttons are 2.1 Turn on backlight and headlights
designed separately. Hold long to turn on backlight and headlights (the
controller should have headlight drive output function); hold
long again to turn off the backlight and headlights.
2.2 Assist ratio gear (ASSIST) switch
Press or to switch 1-5 file gear. Gear 1 is for the
minimum power, gear 5 is for the highest power. Each startup
will automatically restore the gear shutdown last time (the
user can set randomly). Gear 0 is without booster function.
1 UP Button 9 6Km/H push power assist 2.3 6Km/H assist promotion function
2 The brake display 10 i Information Button Hold and flashes, the vehicle drives at the
3 DOWN Button 11 Km/H Riding speed(metric) speed not more than 6Km /h. Release button, the
4 Backlight and headlights 12 MOT Power display function is invalid.
DST Trip distance ℃ Environment temperature
5 13
ODO Total distance ℉ Environment fahrenheit 2.4 Display and delete of single data
6 ASSIST Pas level 14 Battery capacity indicator After power on for 5 seconds, hold and at the
same time, single trip riding time (TM) and single trip
TIM Single trip time AVS Average speed
7 15 distance (DST) flash, hold i button shortly, the content of
TTM Total trip time MXS MAX speed
both is cleared. If failed holding the button within 5 seconds,
8 SW Button
it will automatically return the display interface after 5
seconds, original content is preserved.
Operation
3. Display2
1. ON/OFF
Hold i button shortly in display 1 to enter display 2.
Hold button long to turn on the power, and hold long for a second time to turn off
In the riding mode after 5 seconds, display 2 automatically
the power. When the motor stops driving and when the e-bike is not used for a consecutive 5
returns to display 1, and the original motor power (MOTOR
minutes, it will automatically shut down and turn off the motor power supply.
W) display the output of temperature detection signal).
4. Display 3 Press i button to save and press to go to the next
Hold i button shortly in display 2 to enter display 3. parameter settings.
In the riding condition, five seconds later, a single 3. Set the metric units
maximum speed (MXS) display automatically returns to the The metric units will be set after finishing setting wheel
real riding speed (Km/H). diameter, press i button UNT flash. Press or to
5. In display 3, hold i button shortly,and the display will select the three metric units of speed, mileage, and
re-enter display 1. ambient temperature in synchronization.
6. Hold button to turn off the display and the power supply of controller. Code Speed Mileage Ambient temperature
7. Automatically prompt interface 0 Km/H Km ℃(Centigrade temperature)
7.1 Error Code Display 1 MPH Mil ℃(Centigrade temperature)
1. Motor position sensor fault! 2 Km/H Km ℉（Fahrenheit）
2. THROTTLE fault! 3 MPH Mil ℉（Fahrenheit）
3. Motor or controller short circuit fault! 4. Press i button UNT stop flash after metric unit setting is completed. Hold i button long to exit
Electronic control system failure will display (flashing) fault code. Once the fault from setting environment of routine projects and save the setting values, returning to display
was removed, it automatically exits from the fault code display interface. 5. Exit from routine project setting
7.2 Motor temperature alarm When the motor temperature (the internal motor should be All three routine project settings can exit from the setting environment and return to the
equipped with the temperature sensor and the output of temperature detection signal) is over display by holding i button long after each setting is completed, meanwhile the setting values are
the warning value, MOTOR ℃ (℉) flashes to alarm at any display, meanwhile the motor saved.
controller will offer the appropriate protection to motor. Under each setting interface, if the button failed holding for more than 1 minute, it will
General Project Setting automatically return to display 1, and the setting value is invalid.
1. Set maximum riding speed Outline Drawings and Dimensions
Within power on 5 seconds, hold and at 1. Dimensions of main instrument body 2. Mounting dimensions of double brackets
the same time to enter maximum riding speed Km/H and
MXS setting, press i button maximum riding speed
flashing, then press or to set the maximum
riding speed (default 25Km/H). Press i button to save the
setting, and press to the next parameter settings.
2. Wheel diameter setting 3. Wiring diagram
The wheel diameter will be set after finishing setting
the maximum riding speed, press i button wheel diameter
specifications flashes. Press or to set the
specifications of wheel diameter. Select the range
6,8,10,12,14,16,18,20,22,24,26,700c,28and 29 inches.
