IP5407

2A charge 2.1A / 2.4A discharge integrated DCP

function mobile power SOC
 ESD:4KV, instantaneous withstand
1 Features voltage :11V

 Charge and discharge of synchronous 2 application

switch  Power bank
 2.1A / 2.4A synchronous boost conversion,  Mobile phones, tablets and other portable
2.0A synchronous switch charging devices
 Boost efficiency up to 93%
 Charging efficiency up to 91% 3 Introduction
 Built-in power supply path management,
supporting charging and discharging at the
IP5407 is a multi-function power management
same time
 Double click to turn on the Output supports soc with integrated boost converter, lithium battery
linear compensation of 60mV charge management, and battery power indication,
 charging providing a complete power solution for mobile
 Automatically adjust the charging current to
power.
match the output capability of the adapter
 Support 4.20V,4.35V batteries IP5407 has high integration and rich functions,
 Power display so it only needs few peripheral devices in
 Support 4/2/1 LED power display application，effectively reduce the size of the overall
Supports 4 light models: IP5407
solution and reduce BOM cost.
Support 2/1 light models: IP5407_2D1D
 Multifunction IP5407's synchronous boost system provides
 Built-in floodlight driver 2.1A / 2.4A output current, and the conversion
 Automatically detect phone insertion and efficiency is as high as 93%. At light load, it
removal automatically turns off the LED power indicator
 Integrated mobile phone charging current and maintains the 5V voltage output to sleep, and
intelligent identification DCP
 Support battery NTC temperature protection. the quiescent current drops below 150uA.
 Low power consumption IP5407 uses switch charging technology to
 Output fixed normally open 5V provide 2.0a current at the input, with charging
 Standby power consumption is less than efficiency up to 91%.Built-in IC internal
150uA
temperature and input voltage detection and
 BOM are simple and few intelligent adjustment of charging current.
 Built-in power MOS, single inductor realizes
IP5407 supports 4, 2, 1 LED power display and
charging and discharging
lighting functions.
 Multiple protections and high reliability
IP5407 is available in ESOP8 package.
 Output over-current, over-voltage,
short-circuit protection
 Input overvoltage, overcharge, overdischarge,
overcurrent discharge protection
 over-temperature protection

V1.31 http://www.injoinic.com 1 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
VIN 1 8 VOUT
VIN VOUT
Micro-B TYPE-A
GND GND
2 7 BAT+
DCP DCP SW
C6
Option for EMI/NC

3 KEY
6 VOUT
BAT DCP TYPE-A
GND

4 5

GND
D2 50%
LED1 LED2
D4 100% D3 75%
9
D1 25%

Figure 1 application schematic diagram (4LED indicates power)

4 Pin definition

1 8
VIN VOUT

2 7
DCP SW
power
3 PAD 6
KEY BAT
4 5
LED1 LED2

ESOP8

Figure 2 IP5407 pin diagram

Pin Name Pin Number Pin Description

VIN 1 DC5V charge input pin

DCP 2 Connect to USBA D- D+

KEY 3 Key input, floodlight drive, NTC function reuse pin.

LED1 4 LED drive pin

LED2 5 LED drive pin

Boost input pin, connect the positive electrode of

BAT 6
lithium battery.
SW 7 DC-DC switch pin

VOUT 8 5V boost output pin

PowerPAD Connect to GND

V1.31 http://www.injoinic.com/ 2 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
5 The internal block diagram

VOUT LX
BAT

VBAT+

VIN

Bandgap
OPth

Boost/Charger driver
SYSTEM
CONTROL

KEY/WLED LED
/NTC DRIVER

KEY L2 L1

GND

Figure 3 IP5407 internal block diagram

6 IP series mobile power IC model selection table

Charge and Main feature:
package
discharge
IC Com
Numb flood
TYPE dischar Char USB QC PD3.0 specifica pati
er of light keys I2C DCP
ge ge C 认证 /PPS tion bilit
LED
y
IP5303 1.0A 1.2A 1,2 √ √ - - - - - ESOP8
PIN2PIN

IP5305 1.0A 1.2A 1,2,3,4 √ √ - - - - - ESOP8

IP5306 2.4A 2.1A 1,2,3,4 √ √ √ - - - - ESOP8
IP5406 2.4A 2.1A 1,2,4 √ √ - - - - - ESOP8
IP5407 2.4A 2.1A 1,2,4 √ √ - - - - - ESOP8
IP5207 1.2A 1.2A 3,4,5 √ √ - √ - - - QFN24
IP5207T 1.2A 1.2A 1,2,3,4 √ √ √ √ - - - QFN24
PIN2PIN

IP5109 2.1A 2.1A 3,4,5 √ √ √ - - - - QFN24

IP5209 2.4A 2.1A 3,4,5 √ √ √ √ - - - QFN24
IP5310 3.1A 3.0A 1,2,3,4 √ √ √ √ √ - - QFN32
IP5506 2.4A 2.1A 数码管 √ √ √ - - - - ESOP16
IP5508 2.4A 2.1A Nixie √ √ √ √ - - - QFN32

V1.31 http://www.injoinic.com/ 3 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
tube
IP5322 18W 4.0A 1,2,3,4 √ √ √ √ - √ - QFN32
IP5328P 18W 4.0A 1,2,3,4 √ √ √ √ √ √ √ QFN40

Order model
Order model Instructions
IP5407 Standard product, support 4 lights display
IP5407_4V35 4.35V battery
IP5407_YYY Double click to turn on the light
IP5407_YYY_4V35 Double click to turn on the light，4.35V
battery.
IP5407_2D1D Support two lights and one light display.
IP5407_2D1D _4V35 4.35V battery，support two lights and one
light display

7 Silkscreen instructions

TOP Marking

IP5407
Injoinic Logo
LLLLLLLL

Notes:
IP5407: Part Number
LLLLLL: Lot ID

8 Absolute Maximum Ratings

parameters symbol Value unit
Port input voltage range VIN -0.3 ~6 V
Junction Temperature Range TJ -40 ~ 150 ℃
Storage Temperature Range Tstg -60 ~ 150 ℃
Thermal Resistance
θJA 40 ℃/W
(Junction to Ambient)
ESD (Human Body Model) ESD 4 KV
* Stresses higher than the values listed in the Absolute Maximum Ratings section may cause permanent damage to
the device. Excessive exposure to any absolute maximum rating conditions may affect device reliability and service
life

V1.31 http://www.injoinic.com/ 4 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
9 Recommended working conditions
parameters symbol minimum Classic value maximum unit

Input voltage VIN 4.65 5 6 V

* Beyond these operating conditions, device operating characteristics cannot be guaranteed.

10 Electrical characteristics
unless otherwise stated，TA=25℃，L=1.0uH
minim Classic maxim
parameters symbol Test Conditions. unit
um value um
Charging system.

Input voltage VIN VBAT=3.7V 5 V

Input overvoltage. VINOV 5.6 V

CV constant voltage CV4.2V 4.2V battery configuration. 4.20 V
charging voltage.
CV4.35V 4.345 battery configuration. 4.35 V
Charge cut-off
Istop Input 5V 300 mA
current.
VIN port charging current input terminal
Charge current IVIN 1.9 A
current.
Trickle charging
ITRKL VIN=5v，BAT=2.7v 100 mA
current
Current cut-off
VTRKL 3 V
voltage.
Recharge Voltage
VRCH 4.1 V
Threshold
Charging deadline. TEND 24 Hour

Boost system
Battery operating
VBAT 3 3.7 4.4 V
voltage
Discharge cut-off
VBATLOW IOUT=1A 2.95 V
voltage
VBAT=3.7V @0A 5.0 5.12 5.25 V
DC output voltage. VOUT
VBAT=3.7V @2.1A 4.75 5 5.15 V
Output voltage
ΔVOUT VBAT=3.7V，VOUT=5.0V，fs=500KHz 100 mV
ripple
Boost system
IOVP VBAT=3.7V 2.8 A
over-current

V1.31 http://www.injoinic.com/ 5 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
shutdown current.
Load overcurrent
TUVD output voltage is continuously below 4.2V 30 ms
detect time
Load short-circuit
TOCD Output current continuously higher than 5A 150 us
detection time

Control System.

switching Discharge switching frequency 950 KHz

fs
frequency Charge switching frequency 500 KHz

PMOS on-resistance VBAT=3.7V 40 mΩ

NMOS rDSON
VBAT=3.7V 30 mΩ
on-resistance
VIN and VOUT
rDSON VIN=5V 80 mΩ
PMOS
Input overcurrent
IIDOCP VIN=5V 3 A
protection.
Battery input
ISTB VIN=0V，VBAT=3.7V 100 uA
standby current
LED lighting drive
Ilight 20 mA
current
LED display drive IL1
5 mA
current IL2
Automatic load Load current is continuously less than
TloadD 36 s
detection time 45mA
Light load off lamp
Iplout VABT=3.7V 50 mA
current.
Short press on key
TOnDebounce 50 ms
wake up time
Turn on the light
TKeylight 2 s
time
Thermal shut down
TOTP Rising temperature 150 ℃
temperature
Thermal shut down
ΔTOTP 40 ℃
hysteresis

V1.31 http://www.injoinic.com/ 6 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
11 Function description

Boost

IP5407 integrates a Boost DCDC converter with an output of 5V and a load capacity of 2.1A. The switching
frequency is 950KHz, 3.8V input, and the efficiency is 92% at 5V / 2.1A. Built-in soft-start function to prevent
malfunction caused by excessive inrush current during startup. Integrated output over-current, short-circuit,
over-voltage, over-temperature protection functions When an output overcurrent or short circuit is detected, the
output will be restarted every second to ensure that the system works stably and reliably. lP5407 will turn on the
5V boost output and power display after the BAT voltage is greater than 3.2V. When the output current is less
than 50mA and after 36s, the power display will be turned off and the output voltage will be fixed at 5V to enter
the low power consumption mode. When the IP5407 detects that the BAT voltage is lower than 3.0V, it will turn
off the output. After the BAT voltage rises, it needs to be charged and activated to output normally.

Figure 4 Boost efficiency curve

Charge

IP5407 has a constant current, constant voltage lithium battery charger with a synchronous switch structure.
When the battery voltage is less than 3v, 100mA slip current charging is used; when the battery voltage is greater
than 3V, it enters constant current charging, and the VIN input current limiting loop works; when the battery
voltage is greater than 4.2V, it enters constant voltage charging.After the charging is completed, if the battery
voltage is lower than 4.1V, restart the battery charging
P5407 adopts switch charging technology, with a switching frequency of 500KHz and a charging current of
2.0A at the VIN input terminal. The charging efficiency is up to 91%.
Adaptive power path management, support charge and discharge simultaneously.
IP5407 charging will automatically adjust the charging current to adapt to adapters with different load
capacities, without pulling the charger.

V1.31 http://www.injoinic.com/ 7 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
Key / Lights / NTC

IP5407's keys, lighting lamp drive, and NTC temperature detection are realized by time-multiplexing. Refer
to the schematic diagram in Figure 5
IP5407 can recognize long and short button operation
 The key duration is longer than 50ms, but less than 2s, which is a short press action. A short press will
turn on the power indicator and boost output.
 If the key is pressed for longer than 2s, it is a long-press action. A long-press will turn the lighting LED
on or off.
 There will be no response when the key action is less than 50ms.
IP5407 integrates NTC function to detect battery temperature. When IP5407 is working, NTC
PIN outputs a current of 20uA. At the same time, it detects the voltage of the NTC PIN to
determine the current battery temperature.

KEY HT VH=0.38V/0.56V
COMP
LT VL=1.32V/1.52V
82K RNTC=100K
B=3950
V=20uA*(R1//RNTC)

key flashliggt NTC

Figure 5 Schematic diagram of key, lights, NTC

In the charging state: When NTC PIN detects a voltage of 1.32V, it means that the battery is 0 degrees , and stops
charging the battery;
When NTC PIN detects a voltage of 0.56V, it means that the battery is at 45 degrees, and stops charging the
battery;
In the discharge state:When NTC PIN detects a voltage of 1.52V, it means that the battery is -15 degrees low, and
stops charging to discharge to the outside;
When NTC PIN detects a voltage of 0.38V, it means that the battery is 60 degrees, and stops discharging to
the outside;
If the project does not require NTC, you need to connect the KEY pin to a 51K resistor to GND. Otherwise, it
may cause abnormal charging and discharging. When the IP5407 detects a key press, it will maintain the NTC
detection result before the key is pressed, and the NTC detection returns to normal after the key is released.

V1.31 http://www.injoinic.com/ 8 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
Light display mode

D1 51R
LED1
Four lights
IP5407 D3 D4
D2 51R
LED2 BAT

D1

Two lights LED1

IP5407_2D1D D2
LED2

D1
LED2
One light
1K
IP5407_2D1D LED1
BAT

Figure 6 LED display mode

 4 light mode (IP5407 standard only supports 4 lights)
Discharge
battery capacity C(%) D1 D2 D3 D4

C≥75% ON ON ON ON

50%≤C＜75% ON ON ON OFF

25%≤C＜50% ON ON OFF OFF

3%≤C＜25% ON OFF OFF OFF

0%＜C＜3% 1Hz Flash OFF OFF OFF

V1.31 http://www.injoinic.com/ 9 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
Charge
battery capacity
D1 D2 D3 D4
C(%)
battery full ON ON ON ON

75%≤C ON ON ON 0.5Hz Flash

50%≤C＜75% ON ON 0.5Hz Flash OFF

25%≤C＜50% ON 0.5Hz Flash OFF OFF

C＜25% 0.5Hz Flash OFF OFF OFF

 2 light mode（Custom model： IP5407_2D1D）

status D1 D2
Charge charging process ON OFF
battery full OFF OFF
Discharge regular OFF ON
discharge
low battery OFF 1Hz Flash

 1 light mode （Custom model ：IP5407_2D1D）

status D1
Charge charging process 0.5HZ Flash
battery full ON
Discharge regular discharge ON
low battery 1Hz Flash

Mobile phone charging current intelligent identification DCP

IP5407 integrates the intelligent identification of mobile phone charging current, automatically switches the D
+ and D- line connection for the connected mobile phone device, so that the mobile phone charging current is
adapted to the maximum value, and the mobile phone is charged faster.
Support D+D- short USB dedicated charging port
Support D + application 2.7V voltage, D- application 2.7V voltage Apple 2.4A charging port

V1.31 http://www.injoinic.com/ 10 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
12 Typical application schematic
IP5407 only need inductor, capacitor, resistor to achieve a complete function of the mobile
power solution
VIN 1 8 VOUT
VIN VOUT
Micro-B TYPE-A
C3 22uF C7 22uF C5 22uF
GND GND
R6 2R
2 7 BAT+
DCP DCP SW
L1 1.0UH
C1 10uF
C6
Option for EMI/NC C2 10uF
R2 20R
3 KEY
6 VOUT
BAT DCP TYPE-A
If the lighting function is R1 510R GND
R3 51R
not needed, R1 and R2 can
be omitted R5 82K
4 5
GND
D2 50%
LED1 LED2 R7
If NTC function is not RNTC 100K
BAT+ 1K
needed, R5 sticks 51K, D4 100% D3 75%
9
VDD NC

RNTC can be omitted C6 GND VM

BAT- 0.1uF
D1 25% R4 51R VS VM

IP3025 Lithium protection

circuit

Figure 7 4LED power display typical application schematic

Recommended inductor models:SPM70701R0
Heat Rating Saturation
DC Resistance
Inductance Current Current Measuring
DARFON PIN Tolerance (mΩ)
(uH) DC Amp. DC Amps. Condition
Typ. Max. Idc(A)Max. Isat(A)Max.
SPM70701R0 1.0 ±20% 8.5 8 10 12
Recommended lithium battery IC models
Overcharge Detection Overdischarge Detection Overcurrent
INJOINIC Pack age
Voltage [VCU] (V) Voltage [VDL] (V) Detection Current [IOV] (A)
IP3025A SOT23-6 4.3V 2.5V 7A

V1.31 http://www.injoinic.com/ 11 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
13 Package information.

MILLIMETER
SYMBOL
MIN NOM MAX
A -- -- 1.65
A1 0.05 -- 0.15
A2 1.30 1.40 1.50
A3 0.60 0.65 0.70
b 0.39 -- 0.48
b1 0.38 0.41 0.43
c 0.21 -- 0.25
c1 0.19 0.20 0.21
D 4.70 4.90 5.10
E 5.80 6.00 6.20
E1 3.70 3.90 4.10
e 1.27BSC
L 0.50 0.60 0.80
L1 1.05BSC
θ 0 -- 8º
D1 -- 2.09 --
E2 -- 2.09 --

V1.31 http://www.injoinic.com/ 12 / 13 Copyright © 2019, Injoinic Corp.

 IP5407
IMPORTANT NOTICE
INJOINIC TECHNOLOGY and its subsidiaries reserve the right to make corrections, enhancements,
improvements and other changes to its semiconductor products and services. Buyers should obtain the latest
relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to INJOINIC TECHNOLOGY's
terms and conditions of sale supplied at the time of order acknowledgment.
INJOINIC TECHNOLOGY assumes no liability for applications assistance or the design of Buyers' products.
Buyers are responsible for their products and applications using INJOINIC TECHNOLOGY's components. To
minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and
operating safeguards.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and
safety-related requirements concerning its products, and any use of INJOINIC TECHNOLOGY's components in its
applications, notwithstanding any applications-related information or support that may be provided by INJOINIC
TECHNOLOGY. Buyer represents and agrees that it has all the necessary expertise to create and implement
safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen
the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify
INJOINIC TECHNOLOGY and its representatives against any damages arising out of the use of any INJOINIC
TECHNOLOGY's components in safety-critical applications.
Reproduction of significant portions of INJOINIC TECHNOLOGY's information in INJOINIC TECHNOLOGY's data
books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated
warranties, conditions, limitations, and notices. INJOINIC TECHNOLOGY is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
INJOINIC TECHNOLOGY will update this document from time to time. The actual parameters of the product
may vary due to different models or other items. This document voids all express and any implied warranties.
Resale of INJOINIC TECHNOLOGY's components or services with statements different from or beyond the
parameters stated by INJOINIC TECHNOLOGY for that component or service voids all express and any implied
warranties for the associated INJOINIC TECHNOLOGY's component or service and is an unfair and deceptive
business practice. INJOINIC TECHNOLOGY is not responsible or liable for any such statements.

V1.31 http://www.injoinic.com/ 13 / 13 Copyright © 2019, Injoinic Corp.