20BF8199E2.

book Page 1 Monday, February 28, 2011 10:46 AM

EAU10023

Read this manual carefully before operating this vehicle.

OWNER’S MANUAL

AF115S
20B-F8199-E2

DIC183
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

EAU46090

Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

EAU10050 INTRODUCTION
EAU10102

Welcome to the Yamaha world of motorcycling!

As the owner of the AF115S, you are benefiting from Yamaha’s vast experience and newest technology regarding the design
and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
Please take the time to read this manual thoroughly, so as to enjoy all advantages of your AF115S. The Owner’s Manual
does not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourself and
others from trouble and injury.
In addition, the many tips given in this manual will help keep your motorcycle in the best possible condition. If you have any
further questions, do not hesitate to contact your Yamaha dealer.
The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-
rent product information available at the time of printing, there may be minor discrepancies between your motorcycle and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.
EWA10031

_
WARNING
Please read this manual carefully and completely before operating this motorcycle.
_
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

IMPORTANT MANUAL INFORMATION EAU10122

EAU10132

Particularly important information is distinguished in this manual by the following notations:

This is the safety alert symbol. It is used to alert you to potential personal injury haz-
ards. Obey all safety messages that follow this symbol to avoid possible injury or
death.

A WARNING indicates a hazardous situation which, if not avoided, could result in

WARNING death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid damage to the
NOTICE vehicle or other property.

TIP A TIP provides key information to make procedures easier or clearer.

20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

IMPORTANT MANUAL INFORMATION

EAU37431

AF115S
OWNER’S MANUAL
©2011 by Thai Yamaha Motor Co., Ltd.
1st edition, February 2011
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Thai Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in Thailand.
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

TABLE OF CONTENTS EAU10210

LOCATION OF IMPORTANT FOR YOUR SAFETY – Adjusting the carburetor ............... 7-15
LABELS..............................................1-1 PRE-OPERATION CHECKS ............. 5-1 Adjusting the engine idling
speed ........................................ 7-16
1 SAFETY INFORMATION ..................2-1 OPERATION AND IMPORTANT Adjusting the throttle grip free
Further safe-riding points ................2-5 RIDING POINTS................................. 6-1 play ........................................... 7-17
Helmets ...........................................2-6 Starting and warming up a cold Valve clearance ........................... 7-17
engine ......................................... 6-1 Tires ............................................. 7-18
DESCRIPTION ...................................3-1 Starting a warm engine .................. 6-2 Spoke wheels .............................. 7-19
Left view ..........................................3-1 Starting off ...................................... 6-2 Checking the brake lever free
Right view ........................................3-2 Acceleration and deceleration ........ 6-2 play ........................................... 7-20
Controls and instruments.................3-3 Braking ............................................ 6-3 Adjusting the rear brake lever free
Tips for reducing fuel play ........................................... 7-20
INSTRUMENT AND consumption ............................... 6-3 Checking the front brake pads
CONTROL FUNCTIONS ....................4-1 Engine break-in .............................. 6-4 and rear brake shoes ............... 7-21
Main switch .....................................4-1 Parking ........................................... 6-4 Checking the brake fluid level ...... 7-21
Keyhole cover..................................4-2 General note .................................. 6-5 Changing the brake fluid .............. 7-22
Indicator and warning lights.............4-3 Checking the V-belt ..................... 7-22
Speedometer unit ...........................4-3 PERIODIC MAINTENANCE AND Checking and lubricating the
Fuel gauge ......................................4-4 ADJUSTMENT ................................... 7-1 cables ....................................... 7-23
Handlebar switches ........................4-4 Owner’s tool kit ............................... 7-1 Checking and lubricating the
Front brake lever ............................4-5 Periodic maintenance chart for the throttle grip and cable ............... 7-23
Rear brake lever .............................4-5 emission control system ............. 7-2 Lubricating the front and rear
Fuel tank cap ..................................4-5 General maintenance and brake levers .............................. 7-23
Fuel .................................................4-6 lubrication chart .......................... 7-3 Checking and lubricating the
Catalytic converters ........................4-7 Removing and installing cowlings centerstand and sidestand ....... 7-24
Starter (choke) lever ........................4-8 and panels .................................. 7-6 Checking the front fork ................. 7-25
Kickstarter .......................................4-8 Checking the spark plug ................. 7-8 Checking the steering .................. 7-25
Seat ................................................4-9 Engine oil and oil strainer ............. 7-10 Checking the wheel bearings ....... 7-26
Helmet holders ...............................4-9 Final transmission oil .................... 7-12 Battery ......................................... 7-26
Storage compartment ...................4-10 Air filter and V-belt case air filter Replacing the fuse ....................... 7-28
Luggage hook ...............................4-10 elements ................................... 7-13 Replacing a headlight bulb .......... 7-28
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

TABLE OF CONTENTS
Replacing a front turn signal
light bulb or an auxiliary light
bulb ...........................................7-29
Replacing the tail/brake light bulb
or a rear turn signal light bulb ...7-30
Troubleshooting ............................7-31
Troubleshooting chart ...................7-33

MOTORCYCLE CARE AND

STORAGE ..........................................8-1
Care ................................................8-1
Storage ...........................................8-3

SPECIFICATIONS..............................9-1

CONSUMER INFORMATION...........10-1
Identification numbers ..................10-1
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

LOCATION OF IMPORTANT LABELS EAU45762

EAU10384

Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of
1 your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label
is available from your Yamaha dealer.

123

ZAUU0744

1-1
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

LOCATION OF IMPORTANT LABELS

1 3

Starting and warming up

a cold engine
1. Turn the starter (choke) on and completely close the throttle.
2. Apply either front or rear brake to prevent the motorcycle
move forward while starting.
3. Start the engine by pushing the start switch. (Do not pushing
the start switch continuously more than 2-3 second on any
one atttempt.)
4. After starting the engine, then keep the engine warm by
turning the starter (choke) on about 30 seconds.
5. After finished warming the engine, turn the starter (choke)
completely to the OFF position.

1-2
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION EAU10223

EAUU1070
Safe Riding Therefore:
Be a Responsible Owner
Perform the pre-operation checks each • Wear a brightly colored jacket.
As the vehicle’s owner, you are respon-
time you use the vehicle to make sure it • Use extra caution when you are
sible for the safe and proper operation
is in safe operating condition. Failure to approaching and passing
of your motorcycle.
inspect or maintain the vehicle properly through intersections, since in-
2 Motorcycles are single-track vehicles.
increases the possibility of an accident tersections are the most likely
Their safe use and operation are de-
or equipment damage. See page 5-1 places for motorcycle accidents
pendent upon the use of proper riding
for a list of pre-operation checks. to occur.
techniques as well as the expertise of
● This motorcycle is designed to • Ride where other motorists can
the operator. Every operator should
carry the operator and a passen- see you. Avoid riding in another
know the following requirements before
ger. motorist’s blind spot.
riding this motorcycle.
TIP ● Many accidents involve inexperi-
He or she should:
Although this motorcycle is designed to enced operators. In fact, many op-
● Obtain thorough instructions from
carry a passenger, always comply with erators who have been involved in
a competent source on all aspects
the local regulations. accidents do not even have a cur-
of motorcycle operation.
rent driver’s license.
● Observe the warnings and mainte-
● The failure of motorists to detect • Make sure that you are qualified
nance requirements in this Own-
and recognize motorcycles in traf- and that you only lend your mo-
er’s Manual.
fic is the predominating cause of torcycle to other qualified opera-
● Obtain qualified training in safe
automobile/motorcycle accidents. tors.
and proper riding techniques.
Many accidents have been • Know your skills and limits.
● Obtain professional technical ser-
caused by an automobile driver Staying within your limits may
vice as indicated in this Owner’s
who did not see the motorcycle. help you to avoid an accident.
Manual and/or when made neces-
Making yourself conspicuous ap- • We recommend that you prac-
sary by mechanical conditions.
pears to be very effective in reduc- tice riding your motorcycle
ing the chance of this type of where there is no traffic until you
accident.
2-1
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION
have become thoroughly famil- • The passenger should always ● The use of a jacket, substantial
iar with the motorcycle and all of hold onto the operator, the seat shoes, trousers, gloves, etc., is ef-
its controls. strap or grab bar, if equipped, fective in preventing or reducing
● Many accidents have been with both hands and keep both abrasions or lacerations.
caused by error of the motorcycle feet on the passenger footrests. ● Never wear loose-fitting clothes,
operator. A typical error made by Never carry a passenger unless otherwise they could catch on the 2
the operator is veering wide on a he or she can firmly place both control levers or wheels and cause
turn due to excessive speed or un- feet on the passenger footrests. injury or an accident.
dercornering (insufficient lean an- ● Never ride under the influence of ● Always wear protective clothing
gle for the speed). alcohol or other drugs. that covers your legs, ankles, and
• Always obey the speed limit and ● This motorcycle is designed for feet. The engine or exhaust sys-
never travel faster than warrant- on-road use only. It is not suitable tem become very hot during or af-
ed by road and traffic condi- for off-road use. ter operation and can cause
tions. burns.
• Always signal before turning or Protective Apparel ● A passenger should also observe
changing lanes. Make sure that The majority of fatalities from motorcy- the above precautions.
other motorists can see you. cle accidents are the result of head in-
● The posture of the operator and juries. The use of a safety helmet is the Avoid Carbon Monoxide Poisoning
passenger is important for proper single most critical factor in the preven- All engine exhaust contains carbon
control. tion or reduction of head injuries. monoxide, a deadly gas. Breathing car-
• The operator should keep both ● Always wear an approved helmet. bon monoxide can cause headaches,
hands on the handlebar and ● Wear a face shield or goggles. dizziness, drowsiness, nausea, confu-
both feet on the operator foot- Wind in your unprotected eyes sion, and eventually death.
rests during operation to main- could contribute to an impairment Carbon Monoxide is a colorless, odor-
tain control of the motorcycle. of vision that could delay seeing a less, tasteless gas which may be
hazard. present even if you do not see or smell
any engine exhaust. Deadly levels of
2-2
 20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION
carbon monoxide can collect rapidly ty and handling if the weight distribution as possible and make sure to dis-
and you can quickly be overcome and of the motorcycle is changed. To avoid tribute the weight as evenly as
unable to save yourself. Also, deadly the possibility of an accident, use ex- possible on both sides of the mo-
levels of carbon monoxide can linger treme caution when adding cargo or torcycle to minimize imbalance or
for hours or days in enclosed or poorly accessories to your motorcycle. Use instability.
2 ventilated areas. If you experience any extra care when riding a motorcycle ● Shifting weights can create a sud-
symptoms of carbon monoxide poison- that has added cargo or accessories. den imbalance. Make sure that ac-
ing, leave the area immediately, get Here, along with the information about cessories and cargo are securely
fresh air, and SEEK MEDICAL TREAT- accessories below, are some general attached to the motorcycle before
MENT. guidelines to follow if loading cargo to riding. Check accessory mounts
● Do not run engine indoors. Even if your motorcycle: and cargo restraints frequently.
you try to ventilate engine exhaust The total weight of the operator, • Properly adjust the suspension
with fans or open windows and passenger, accessories and cargo for your load (suspension-ad-
doors, carbon monoxide can rap- must not exceed the maximum load justable models only), and
idly reach dangerous levels. limit. Operation of an overloaded ve- check the condition and pres-
● Do not run engine in poorly venti- hicle could cause an accident. sure of your tires.
lated or partially enclosed areas • Never attach any large or heavy
such as barns, garages, or car- Maximum load: items to the handlebar, front
ports. 163 kg (359 lb) fork, or front fender. Such items
● Do not run engine outdoors where can create unstable handling or
When loading within this weight limit,
engine exhaust can be drawn into a slow steering response.
keep the following in mind:
a building through openings such ● This vehicle is not designed to
● Cargo and accessory weight
as windows and doors. pull a trailer or to be attached to
should be kept as low and close to
a sidecar.
the motorcycle as possible. Se-
Loading
curely pack your heaviest items as
Adding accessories or cargo to your
close to the center of the vehicle
motorcycle can adversely affect stabili-
2-3
20BF8199E2.book Page 4 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION
Genuine Yamaha Accessories cause of potential safety hazards to are added to the handlebar or
Choosing accessories for your vehicle you or others. Installing aftermarket front fork area, they must be as
is an important decision. Genuine products or having other modifications lightweight as possible and
Yamaha accessories, which are avail- performed to your vehicle that change should be kept to a minimum.
able only from a Yamaha dealer, have any of the vehicle’s design or operation • Bulky or large accessories may
been designed, tested, and approved characteristics can put you and others seriously affect the stability of 2
by Yamaha for use on your vehicle. at greater risk of serious injury or death. the motorcycle due to aerody-
Many companies with no connection to You are responsible for injuries related namic effects. Wind may at-
Yamaha manufacture parts and acces- to changes in the vehicle. tempt to lift the motorcycle, or
sories or offer other modifications for Keep the following guidelines in mind, the motorcycle may become un-
Yamaha vehicles. Yamaha is not in a as well as those provided under “Load- stable in cross winds. These ac-
position to test the products that these ing” when mounting accessories. cessories may also cause
aftermarket companies produce. ● Never install accessories or carry instability when passing or be-
Therefore, Yamaha can neither en- cargo that would impair the perfor- ing passed by large vehicles.
dorse nor recommend the use of ac- mance of your motorcycle. Care- • Certain accessories can dis-
cessories not sold by Yamaha or fully inspect the accessory before place the operator from his or
modifications not specifically recom- using it to make sure that it does her normal riding position. This
mended by Yamaha, even if sold and not in any way reduce ground improper position limits the free-
installed by a Yamaha dealer. clearance or cornering clearance, dom of movement of the opera-
limit suspension travel, steering tor and may limit control ability,
Aftermarket Parts, Accessories, and travel or control operation, or ob- therefore, such accessories are
Modifications scure lights or reflectors. not recommended.
While you may find aftermarket prod- • Accessories fitted to the handle- ● Use caution when adding electri-
ucts similar in design and quality to bar or the front fork area can cal accessories. If electrical acces-
genuine Yamaha accessories, recog- create instability due to improp- sories exceed the capacity of the
nize that some aftermarket accessories er weight distribution or aerody- motorcycle’s electrical system, an
or modifications are not suitable be- namic changes. If accessories
2-4
 20BF8199E2.book Page 5 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION
electric failure could result, which ● Secure the motorcycle with tie- EAU10373

could cause a dangerous loss of downs or suitable straps that are Further safe-riding points
● Be sure to signal clearly when
lights or engine power. attached to solid parts of the mo-
torcycle, such as the frame or up- making turns.
Aftermarket Tires and Rims per front fork triple clamp (and not, ● Braking can be extremely difficult
2 The tires and rims that came with your for example, to rubber-mounted on a wet road. Avoid hard braking,
motorcycle were designed to match the handlebars or turn signals, or parts because the scooter could slide.
performance capabilities and to pro- that could break). Choose the lo- Apply the brakes slowly when
vide the best combination of handling, cation for the straps carefully so stopping on a wet surface.
braking, and comfort. Other tires, rims, ● Slow down as you approach a cor-
the straps will not rub against
sizes, and combinations may not be painted surfaces during transport. ner or turn. Once you have com-
appropriate. Refer to page 7-18 for tire ● The suspension should be com-
pleted a turn, accelerate slowly.
specifications and more information on ● Be careful when passing parked
pressed somewhat by the tie-
replacing your tires. downs, if possible, so that the mo- cars. A driver might not see you
torcycle will not bounce excessive- and open a door in your path.
Transporting the Motorcycle ● Railroad crossings, streetcar rails,
ly during transport.
Be sure to observe following instruc- iron plates on road construction
tions before transporting the motorcy- sites, and manhole covers be-
cle in another vehicle. come extremely slippery when
● Remove all loose items from the wet. Slow down and cross them
motorcycle. with caution. Keep the scooter up-
● Point the front wheel straight right, otherwise it could slide out
ahead on the trailer or in the truck from under you.
bed, and choke it in a rail to pre- ● The brake pads could get wet
vent movement. when you wash the scooter. After
washing the scooter, check the
brakes before riding.
2-5
20BF8199E2.book Page 6 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION
● Always wear a helmet, gloves, EAUU0030

trousers (tapered around the cuff Helmets

and ankle so they do not flap), and Operating this vehicle without an ap-
a bright colored jacket. proved motorcycle helmet increases
● Do not carry too much luggage on your chances of a severe head injury or
the scooter. An overloaded scoot- death in the event of an accident. The 2
er is unstable. Use a strong cord to majority of fatalities from motorcycle or
secure any luggage to the carrier scooter accidents are the result of head
(if equipped). A loose load will af- injuries. The use of a safety helmet is ZAUU0003

fect the stability of the scooter and the single most critical factor in the pre- Correctly helmet wearing
could divert your attention from the vention or reduction of head injuries.
road. (See page 2-3.)
Always select an approved
motorcycle helmet
Pay attention to the following when
choosing a motorcycle helmet.
● The helmet must meet the safety
standard “TIS”.
● The helmet size must match the
ZAUU0007
size of the rider’s head.
Incorrectly helmet wearing
● Never subject a helmet to heavy
shocks. Wearing the helmet correctly
Always connect the chin strap. In the
case of an accident, the helmet has a
much less chance of coming off if the
chin strap is connected.

2-6
 20BF8199E2.book Page 7 Monday, February 28, 2011 10:46 AM

SAFETY INFORMATION
Types of helmets and their usage
● Half-type: use only for riding at low
speeds

ZAUU0004

● Full-type: use only for riding at low

to mid-range speeds

ZAUU0005

● Full-face-type: use for riding at

mid-range to high speeds

ZAUU0006

2-7
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

EAU10401 DESCRIPTION
EAU10410

Left view
1 2 3 4 5 6 7 8

ZAUU0745 11 10 9
1. Headlight/Auxiliary lights (page 7-28, 7-29) 10.Engine oil drain bolt A (page 7-11)
2. Front turn signal lights (page 7-29) 11.Engine oil drain bolt B (page 7-11)
3. Luggage hook (page 4-10)
4. Throttle stop screw (page 7-16)
5. Owner’s tool kit (page 7-1)
6. Seat lock (page 4-9)
7. Rear turn signal lights (page 7-30)
8. Tail/brake light (page 7-30)
9. Kickstarter (page 4-8)
3-1
 20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

DESCRIPTION
EAU10420

Right view
1 2 3 4 5 6

ZAUU0746 7
1. Fuel tank cap (page 4-5)
2. Air filter element (page 7-13)
3. Dry battery (page 7-26)
4. Fuse (page 7-28)
5. Helmet holder (page 4-9)
6. Front brake fluid reservoir (page 7-21)
7. Engine oil filler cap (page 7-10)

3-2
20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

DESCRIPTION
EAU10430

Controls and instruments

1 2 3 4 5 6 7 8

ZAUU0747

1. Rear brake lever (page 4-5)

2. Starter (choke) lever (page 4-8)
3. Left handlebar switches (page 4-4)
4. Fuel gauge (page 4-4)
5. Speedometer unit (page 4-3)
6. Right handlebar switches (page 4-4)
7. Throttle grip (page 7-17)
8. Front brake lever (page 4-5)
9. Main switch (page 4-1)
3-3
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS EAU1044P

EAUU0061
TIP To lock the steering
Main switch _

The headlight, auxiliary lights, meter

lighting and taillight come on automati-
cally when the engine is started.
_

EAU10661

OFF
All electrical systems are off. The key
can be removed.
EWA10061
ZAUU0013
4 ZAUU0748 WARNING
_ 1. Turn the handlebars all the way to
Never turn the key to “OFF” or the left.
The main switch controls the ignition
“LOCK” while the vehicle is moving. 2. Push the key in from the “OFF” po-
and lighting systems. The various main
Otherwise the electrical systems will sition, release it, and then turn it to
switch positions are described below.
be switched off, which may result in “LOCK”.
TIP
_
loss of control or an accident. 3. Remove the key.
The main switch is equipped with a _

keyhole cover. (See page 4-2.) EAU10701

LOCK
EAU37441 The steering is locked, and all electrical
ON systems are off. The key can be re-
All electrical circuits are supplied with moved.
power, and the engine can be started.
The key cannot be removed.

4-1
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

To unlock the steering EAUU0070
turn the key to the left to open the cov-
Keyhole cover er.

To close the keyhole cover

ZAUU0014
ZAUU0015 4
Insert the key and turn it to “OFF”.
1. Ignition key
2. Safety key ZAUU0017

Insert the key head into the keyhole

To open the keyhole cover
cover receptacle as shown, and then
turn the key to the right to close the
cover.

ZAUU0016

Insert the key head into the keyhole

cover receptacle as shown, and then

4-2
 20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

EAU11004
The electrical circuit of the warning light EAUT1821

Indicator and warning lights can be checked by turning the key to Speedometer unit
2 1 3 “ON”. The warning light should come 1 2
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
km/h a Yamaha dealer check the electrical km/h
circuit.
4 ZAUU0749 ZAUU0750
EAU11020
1. High beam indicator light “ ” Turn signal indicator light “ ” 1. Speedometer
2. Engine trouble warning light “ ” This indicator light flashes when the 2. Odometer
3. Turn signal indicator light “ ” turn signal switch is pushed to the left The speedometer unit is equipped with
EAU11080
or right. a speedometer and an odometer. The
High beam indicator light “ ” speedometer shows the riding speed.
This indicator light comes on when the The odometer shows the total distance
high beam of the headlight is switched traveled.
on.

EAU11484

Engine trouble warning light “ ”

This warning light comes on if a prob-
lem is detected in the electrical circuit
monitoring the engine. If this occurs,
have a Yamaha dealer check the self-
diagnosis system.

4-3
20BF8199E2.book Page 4 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

EAU12140 EAU12348

Fuel gauge Handlebar switches EAU12400

Dimmer switch “ / ”
1 Left Set this switch to “ ” for the high
beam and to “ ” for the low beam.

EAU12460

Turn signal switch “ / ”

To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
ZAUU0751 turn, push this switch to “ ”. When re- 4
1. Fuel gauge leased, the switch returns to the center
ZAUU0020 position. To cancel the turn signal
The fuel gauge indicates the amount of
1. Dimmer switch “ / ” lights, push the switch in after it has re-
fuel in the fuel tank. The needle moves
2. Turn signal switch “ / ” turned to the center position.
towards “E” (Empty) as the fuel level
3. Horn switch “ ”
decreases. When the needle reaches EAU12500

“E”, refuel as soon as possible. Horn switch “ ”

Right
Press this switch to sound the horn.
TIP
_

Do not allow the fuel tank to empty itself EAUM1132

completely. Start switch “ ”

_
Push this switch while applying the
front or rear brake to crank the engine
with the starter. See page 6-1 for start-
ing instructions prior to starting the en-
gine.
ZAUU0021

1. Start switch “ ”

4-4
 20BF8199E2.book Page 5 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

EAU12900 EAU12950 EAU37471

Front brake lever Rear brake lever Fuel tank cap

4 ZAUU0022 ZAUU0159 ZAUU0024

1. Front brake lever 1. Rear brake lever 1. Fuel tank cap

a. Open.
The front brake lever is located on the The rear brake lever is located on the
b. Close.
right handlebar grip. To apply the front left handlebar grip. To apply the rear
brake, pull this lever toward the handle- brake, pull this lever toward the handle-
To remove the fuel tank cap
bar grip. bar grip.
1. Open the seat. (See page 4-9.)
2. Turn the fuel tank cap counter-
clockwise and pull it off.

4-5
20BF8199E2.book Page 6 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

EAU13212
other sources of ignition such as
Fuel the pilot lights of water heaters and
clothes dryers.
2. Do not overfill the fuel tank. Stop
filling when the fuel reaches the
bottom of the filler tube. Because
fuel expands when it heats up,
heat from the engine or the sun
ZAUU0025 can cause fuel to spill out of the
ZAUU0026 fuel tank. 4
To install the fuel tank cap 3. Wipe up any spilled fuel immedi-
1. Fuel tank filler tube
1. Insert the fuel tank cap into the ately. NOTICE: Immediately
2. Fuel level
tank opening and turn it clockwise wipe off spilled fuel with a
until the “ ” marks on the cap Make sure there is sufficient gasoline in
clean, dry, soft cloth, since fuel
and tank are aligned. the tank.
EWA10881
may deteriorate painted surfac-
2. Close the seat. es or plastic parts. [ECA10071]
EWA11091 WARNING
_
4. Be sure to securely close the fuel
WARNING Gasoline and gasoline vapors are
_
tank cap.
Make sure that the fuel tank cap is extremely flammable. To avoid fires EWA15151

properly closed after filling fuel. and explosions and to reduce the WARNING
Leaking fuel is a fire hazard. risk of injury when refueling, follow _

Gasoline is poisonous and can

_
these instructions.
_
cause injury or death. Handle gaso-
1. Before refueling, turn off the en- line with care. Never siphon gaso-
gine and be sure that no one is sit- line by mouth. If you should swallow
ting on the vehicle. Never refuel some gasoline or inhale a lot of gas-
while smoking, or while in the vi- oline vapor, or get some gasoline in
cinity of sparks, open flames, or your eyes, see your doctor immedi-
4-6
 20BF8199E2.book Page 7 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

ately. If gasoline spills on your skin, Yamaha products can use gasohol EAU13445

wash with soap and water. If gaso- [E10] Octane 91 or higher. However, Catalytic converters
line spills on your clothing, change when filling with gasohol, cold engine This vehicle is equipped with catalytic
your clothes. starting may be difficult. Therefore, be converters in the exhaust system.
EWA10862
_

sure to follow the procedures in “Start-

WARNING
EAUU0042 ing a cold engine”. _

ECAU0010 The exhaust system is hot after op-

Recommended fuel: NOTICE eration. To prevent a fire hazard or
Regular unleaded gasoline or gaso- _

burns:
Using gasohol may cause engine
hol (91 min. pump octane) ● Do not park the vehicle near
4 Fuel tank capacity: trouble depending on the engine. If
gasohol is used and engine trouble possible fire hazards such as
4.1 L (1.08 US gal) (0.90 Imp.gal)
occurs, contact your Yamaha dealer grass or other materials that
ECA11400
as soon as possible. easily burn.
NOTICE _ ● Park the vehicle in a place
_

Use only unleaded gasoline. The where pedestrians or children

use of leaded gasoline will cause se- are not likely to touch the hot
vere damage to internal engine exhaust system.
parts, such as the valves and piston ● Make sure that the exhaust sys-
rings, as well as to the exhaust sys- tem has cooled down before do-
tem. ing any maintenance work.
_
● Do not allow the engine to idle

Gasohol more than a few minutes. Long

Gasohol is a mixture of unleaded gaso- idling can cause a build-up of
line and ethanol. Gasohol contains heat.
_

90% gasoline and 10% ethanol which

is called “E10”.

4-7
20BF8199E2.book Page 8 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

ECA10701 EAU13590 EAU37650

NOTICE Starter (choke) lever “ ” Kickstarter

_

Use only unleaded gasoline. The

use of leaded gasoline will cause
unrepairable damage to the catalytic
converter.
_

ZAUU0027 ZAUU0028 4
1. Starter (choke) lever “ ” 1. Kickstarter

Starting a cold engine requires a richer If the engine fails to start by pushing the
air-fuel mixture, which is supplied by start switch, try to start it by using the
the starter (choke). kickstarter. To start the engine, fold out
Move the lever in direction (a) to turn on the kickstarter lever, move it down light-
the starter (choke). ly with your foot until the gears engage,
Move the lever in direction (b) to turn off and then push it down smoothly but
the starter (choke). forcefully.

4-8
 20BF8199E2.book Page 9 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

EAU13891 EAU37481
To release a helmet from a helmet
Seat Helmet holders holder
Open the seat, remove the helmet from
To open the seat
the helmet holder, and then close the
1. Insert the key in the lock, and then seat.
turn it as shown.
2. Fold the seat up.

4 ZAUU0030

1. Seat lock
2. Helmet holders (✕ 2)

The helmet holders are located under

the seat.
ZAUU0029

1. Seat lock To secure a helmet to a helmet

2. Seat
holder
1. Open the seat. (See page 4-9.)
To close the seat
2. Attach a helmet to a helmet hold-
1. Fold the seat down, and then push
er, and then securely close the
it down to lock it in place.
seat. WARNING! Never ride with
2. Remove the key.
a helmet attached to the helmet
TIP
_
holder, since the helmet may hit
Make sure that the seat is properly se- objects, causing loss of control
cured before riding. and possibly an accident. [EWA10161]
_

4-9
20BF8199E2.book Page 10 Monday, February 28, 2011 10:46 AM

INSTRUMENT AND CONTROL FUNCTIONS

EAU14532
● Since the storage compartment EAUT1072

Storage compartment accumulates heat when ex- Luggage hook

posed to the sun and/or the en-
gine heat, do not store anything
susceptible to heat, consum-
ables or flammable items inside
it.
● To avoid humidity from spread-
ing through the storage com-
ZAUU0031 partment, wrap wet articles in a ZAUU0032 4
1. Storage compartment plastic bag before storing them 1. Luggage hook
There is a storage compartment under in the compartment. EWAT1031
● Since the storage compartment
the seat. WARNING
EWA10961 may get wet while the scooter is _

● Do not exceed the load limit of

WARNING being washed, wrap any articles
_
1 kg (2.2 lb) for the luggage
● Do not exceed the load limit of stored in the compartment in a
hook.
1 kg (2.2 lb) for the storage com- plastic bag.
● Do not exceed the maximum
partment. ● Do not keep anything valuable
load of 163 kg (369 lb) for the ve-
● Do not exceed the maximum or breakable in the storage
hicle.
load of 163 kg (359 lb) for the ve- compartment.
_

hicle.
_ TIP
_

ECA10081 Do not leave your scooter unattended

NOTICE with the seat open.
_
_

Keep the following points in mind

when using the storage compart-
ment.
4-10
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

FOR YOUR SAFETY – PRE-OPERATION CHECKS EAU15582

EAU15596

Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151

WARNING
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
ITEM CHECKS PAGE
• Check fuel level in fuel tank.
5 Fuel • Refuel if necessary. 4-6
• Check fuel line for leakage.
• Check oil level in engine.
Engine oil • If necessary, add recommended oil to specified level. 7-10
• Check vehicle for oil leakage.
Final transmission oil • Check vehicle for oil leakage. 7-12
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Front brake • Replace if necessary. 7-21
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• Lubricate cable if necessary.
Rear brake 7-20
• Check lever free play.
• Adjust if necessary.

5-1
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

FOR YOUR SAFETY – PRE-OPERATION CHECKS

ITEM CHECKS PAGE
• Make sure that operation is smooth.
• Check throttle grip free play.
Throttle grip 7-17, 7-23
• If necessary, have Yamaha dealer adjust throttle grip free play and lubricate cable and
grip housing.
• Make sure that operation is smooth.
Control cables 7-23
• Lubricate if necessary.
• Check for damage.
• Check tire condition and tread depth.
Wheels and tires 7-18, 7-19
• Check air pressure.
• Correct if necessary.
• Make sure that operation is smooth.
Brake levers 7-23
• Lubricate lever pivoting points if necessary.
• Make sure that operation is smooth.
Centerstand, sidestand 7-24
• Lubricate pivots if necessary.
5
• Make sure that all nuts, bolts and screws are properly tightened.
Chassis fasteners —
• Tighten if necessary.
Instruments, lights, signals and • Check operation.
—
switches • Correct if necessary.

5-2
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

OPERATION AND IMPORTANT RIDING POINTS EAU15944

EAU15951 EAUU0205
If the engine fails to start, release
Starting and warming up a the start switch, wait a few sec-
Read the Owner’s Manual carefully to cold engine onds, and then try again. Each
become familiar with all controls. If
starting attempt should be as short
there is a control or function you do not
as possible to preserve the bat-
understand, ask your Yamaha dealer.
EWA10271
tery. Do not crank the engine more
WARNING than 5 seconds on any one at-
_

tempt. If the engine does not start

Failure to familiarize yourself with
with the starter motor, try using the
the controls can lead to loss of con-
kickstarter with the motorcycle on
trol, which could cause an accident
the centerstand.
or injury. ZAUU0033
_

1. Starter (choke) lever “ ”

TIP
_

EAUV0120
ECAV0030
ECA10250 If the engine fails to start several times
6 NOTICE by pushing the start switch, try again
NOTICE _

_
See page 6-4 for engine break-in in- with the throttle grip 1/8 to 1/4 open.
Do not ride in water that is deep _

structions prior to operating the ve- 4. After starting the engine, move the
enough to allow engine parts, espe-
hicle for the first time. starter (choke) back halfway.
cially the air filter intake, to become _

wet or submersed. If the engine is al- 1. Turn the key to “ON”. 5. When the engine is warm, turn the
lowed to be submersed in water, be 2. Turn on the starter (choke) and starter (choke) off.
ECA11042
sure to remove the water from the completely close the throttle grip.
air filter case as soon as possible to (See page 4-8.) NOTICE
_

prevent extensive engine damage. 3. Start the engine by pushing the For maximum engine life, never ac-
(See “PERIODIC MAINTENANCE start switch, while applying the celerate hard when the engine is
AND ADJUSTMENT” for details.) front or rear brake or by pushing cold!
_
_

the kickstarter lever down.

6-1
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

OPERATION AND IMPORTANT RIDING POINTS

EAU16640 EAU16761 EAU16780

Starting a warm engine Starting off Acceleration and deceleration

Follow the same procedure as for start-
ing a cold engine with the exception TIP
_

Before starting off, allow the engine to

that the starter (choke) is not required
warm up.
when the engine is warm. _

1. While pulling the rear brake lever

km/h
with your left hand and holding the
grab bar with your right hand, push
the scooter off the centerstand.
2. Sit astride the seat, and then ad- ZAUU0752

just the rear view mirrors. The speed can be adjusted by opening
3. Switch the turn signals on. and closing the throttle. To increase the
4. Check for oncoming traffic, and speed, turn the throttle grip in direction
then slowly turn the throttle grip (a). To reduce the speed, turn the throt- 6
(on the right) in order to take off. tle grip in direction (b).
5. Switch the turn signals off.

6-2
 20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

OPERATION AND IMPORTANT RIDING POINTS

EAU16793 EWA10300 EAU16820

Braking WARNING Tips for reducing fuel

_

● Avoid braking hard or suddenly consumption

Front brake (especially when leaning over to Fuel consumption depends largely on
one side), otherwise the scooter your riding style. Consider the following
may skid or overturn. tips to reduce fuel consumption:
● Railroad crossings, streetcar ● Avoid high engine speeds during
rails, iron plates on road con- acceleration.
struction sites, and manhole ● Avoid high engine speeds with no
covers become extremely slip- load on the engine.
pery when wet. Therefore, slow ● Turn the engine off instead of let-
down when approaching such ting it idle for an extended length of
ZAUU0037
areas and cross them with cau- time (e.g., in traffic jams, at traffic
tion. lights or at railroad crossings).
6 Rear brake ● Keep in mind that braking on a
wet road is much more difficult.
● Ride slowly down a hill, as brak-
ing downhill can be very diffi-
cult.
_

1. Close the throttle completely.

2. Apply both front and rear brakes
simultaneously while gradually in-
ZAUU0038 creasing the pressure.

6-3
20BF8199E2.book Page 4 Monday, February 28, 2011 10:46 AM

OPERATION AND IMPORTANT RIDING POINTS

EAU16830
150–500 km (90–300 mi) EAU17213

Engine break-in Avoid prolonged operation above 1/2 Parking

There is never a more important period throttle. When parking, stop the engine, and
in the life of your engine than the period Rev the engine freely through the then remove the key from the main
between 0 and 1000 km (600 mi). For gears, but do not use full throttle at any switch.
this reason, you should read the follow- time.
EWA10311

ing material carefully. _

WARNING
Since the engine is brand new, do not ● Since the engine and exhaust
500–1000 km (300–600 mi)
put an excessive load on it for the first Avoid prolonged operation above 3/4 system can become very hot,
1000 km (600 mi). The various parts in throttle. park in a place where pedestri-
the engine wear and polish themselves ans or children are not likely to
to the correct operating clearances. 1000 km (600 mi) and beyond touch them and be burned.
During this period, prolonged full-throt- Avoid prolonged full-throttle operation. ● Do not park on a slope or on
tle operation or any condition that might Vary the engine speed occasionally. soft ground, otherwise the vehi-
result in engine overheating must be NOTICE: After 1000 km (600 mi) of cle may overturn, increasing the 6
avoided. operation, the engine oil must be risk of a fuel leak and fire.
changed, the oil filter cartridge or el- ● Do not park near grass or other
EAU37792
ement replaced, and the oil strainer flammable materials which
0–150 km (0–90 mi)
cleaned. If any engine trouble might catch fire.
Avoid prolonged operation above 1/3 _

throttle. should occur during the engine

After every hour of operation, stop the break-in period, immediately have a
engine, and then let it cool for five to ten Yamaha dealer check the vehicle.
[ECA10362]
minutes.
Vary the engine speed from time to
time. Do not operate the engine at one
set throttle position.

6-4
 20BF8199E2.book Page 5 Monday, February 28, 2011 10:46 AM

OPERATION AND IMPORTANT RIDING POINTS

EAUU1240

General note
Much can be gained from the correct use and maintenance of a motorcycle.

1. THE CUSTOMERS CAN USE THE FULLEST 2. A MOTORCYCLE CAN KEEP ITS PERFORMANCE
POTENTIAL OF YAMAHA MOTORCYCLES CAPABILITY FOR A LONGER TIME

Comparison of wear on engine parts

(piston, piston ring, cylinder, etc.)
100% With maintenance

Perfect operative
condition
Without
maintenance

6
Distance
covered (km) Engine overhaul, cylinder
boring, piston ring change, etc.
ZAUU0736

6-5
20BF8199E2.book Page 6 Monday, February 28, 2011 10:46 AM

OPERATION AND IMPORTANT RIDING POINTS

3. FUEL COST AND REPAIR EXPENSES CAN BE 4. A MOTORCYCLE CAN DEMAND A HIGH PRICE
KEPT TO A MINIMUM WHEN IT IS TRADED IN AS A USED PRODUCT

Fuel consumption
With maintenance
100%

Without
maintenance
Distance covered (km)

Customer’s running cost

(fuel cost plus maintenance and repair expenses)
S Without maintenance
Big repairs at higher expenses 6
With maintenance

Distance covered (km)

ZAUU0737

6-6
 20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT EAU1722F

EAU17244 EWA15122 EAU17542

WARNING Owner’s tool kit

Periodic inspection, adjustment, and _

lubrication will keep your vehicle in the Turn off the engine when performing
safest and most efficient condition pos- maintenance unless otherwise
sible. Safety is an obligation of the vehi- specified.
● A running engine has moving
cle owner/operator. The most impor-
tant points of vehicle inspection, adjust- parts that can catch on body
ment, and lubrication are explained on parts or clothing and electrical
the following pages. parts that can cause shocks or
The intervals given in the periodic fires.
ZAUU0039
● Running the engine while ser-
maintenance charts should be simply 1. Owner’s tool kit
considered as a general guide under vicing can lead to eye injury,
burns, fire, or carbon monoxide The owner’s tool kit is located under
normal riding conditions. However, de-
poisoning – possibly leading to the passenger seat. (See page 4-9.)
pending on the weather, terrain, geo-
death. See page 2-2 for more in- The service information included in this
graphical location, and individual use,
formation about carbon monox- manual and the tools provided in the
the maintenance intervals may need to
ide. owner’s tool kit are intended to assist
7 be shortened.
EWA10321
_

EWA15460
you in the performance of preventive
WARNING WARNING maintenance and minor repairs. How-
_ _
ever, additional tools such as a torque
Failure to properly maintain the ve- Brake discs, calipers, drums, and
wrench may be necessary to perform
hicle or performing maintenance ac- linings can become very hot during
certain maintenance work correctly.
tivities incorrectly may increase use. To avoid possible burns, let
your risk of injury or death during brake components cool before TIP
_

service or while using the vehicle. If touching them. If you do not have the tools or experi-
you are not familiar with vehicle ser- _

ence required for a particular job, have

vice, have a Yamaha dealer perform a Yamaha dealer perform it for you.
service. _

7-1
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU0620

TIP
_

● The annual checks must be performed every year, except if a kilometer-based maintenance is performed in-
stead.
● From 20000 km, repeat the maintenance intervals starting from 4000 km.
● Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and techni-
cal skills.
_

EAUU1290

Periodic maintenance chart for the emission control system

ODOMETER READING (km)
1000 4000 8000 12000 16000 ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB
or or or or or CHECK
2 months 6 months 10 months 14 months 18 months
1 * Fuel line • Check fuel and vacuum hoses for cracks or
√ √ √ √ √
damage.
2 Spark plug • Check condition. 7
√ √ √ √
• Clean and regap.
• Replace. Every 10000 km (6000 mi)
3 * Valves • Check valve clearance.
√ √
• Adjust if necessary.
4 * Carburetor • Adjust engine idling speed. √ √ √ √ √ √
5 * Muffler and exhaust pipe • Check the screw clamp(s) for looseness. √ √ √ √ √
6 * Air induction system • Check the air cut-off valve, reed valve, and hose
for damage. √ √ √ √ √
• Replace any damaged parts if necessary.

7-2
 20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU1280

General maintenance and lubrication chart

ODOMETER READING (km)
1000 4000 8000 12000 16000 ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
or or or or or
2 months 6 months 10 months 14 months 18 months
1 Air filter element • Replace. Every 16000 km (10000 mi)
2 Air filter check hose • Clean. √ √ √ √ √
3 * V-belt case air filter • Clean.
√ √ √ √
element • Replace if necessary.
4 * Battery (MF type) • Check battery voltage.
• Change battery if necessary. √ √ √ √ √ √

5 * Front brake • Check operation, fluid level and vehicle for fluid √ √ √ √ √ √
leakage.
• Replace brake pads. Whenever worn to the limit
6 * Rear brake • Check operation and adjust brake lever free √ √ √ √ √ √
play.
• Replace brake shoes. Whenever worn to the limit
7 * Brake hose • Check for cracks or damage.
7 • Check for correct routing and clamping. √ √ √ √ √

• Replace. Every 4 years

8 * Wheels (spoke) • Check runout, spoke tightness and for damage.
• Tighten spokes if necessary. √ √ √ √ √

9 * Tires • Check tread depth and for damage.

• Replace if necessary.
• Check air pressure. √ √ √ √ √
• Correct if necessary.
10 * Wheel bearings • Check bearing for looseness or damage. √ √ √ √
11 * Swingarm • Check operation and for excessive play. √ √ √ √
• Lubricate with lithium-soap-based grease. Every 12000 km (7500 mi)

7-3
20BF8199E2.book Page 4 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

ODOMETER READING (km)
1000 4000 8000 12000 16000 ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB
or or or or or CHECK
2 months 6 months 10 months 14 months 18 months
12 * Steering bearings • Check bearing play and steering for roughness. √ √ √ √ √
• Lubricate with lithium-soap-based grease. Every 12000 km (7500 mi)
13 * Chassis fasteners • Make sure that all nuts, bolts and screws are √ √ √ √ √
properly tightened.
14 Sidestand, centerstand • Check operation.
√ √ √ √ √
• Lubricate with lithium-soap-based grease.
15 * Front fork • Check operation and for oil leakage. √ √ √ √
• Change the front fork oil. Every 20000 km (12000 mi)
16 * Shock absorber • Check operation and shock absorber for oil √ √ √ √
assembly leakage.
17 Engine oil • Change. Every 4000 km
√ √
• Check oil level and vehicle for oil leakage. (2400 mi)
18 * Engine oil strainer • Clean. √ √
19 Final transmission oil • Check vehicle for oil leakage. √ √ Every 8000 km (5000 mi)
• Replace. √ Every 12000 km (7500 mi) 7
20 * V-belt • Check for damage and wear. √ √ √ √
• Replace. Every 25000 km (15500 mi)
21 * V-belt secondary sheave • Lubricate. Every 12000 km (7500 mi)
22 * Front and rear brake
• Check operation. √ √ √ √ √ √
switches
23 Moving parts and cables • Lubricate. √ √ √ √ √
24 * Throttle grip • Check operation.
• Check throttle grip free play, and adjust if √ √ √ √ √
necessary.
• Lubricate cable and grip housing.
25 * Lights, signals and • Check operation. √ √ √ √ √ √
switches • Adjust headlight beam.

7-4
 20BF8199E2.book Page 5 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU0771

TIP
_

● Air filter
• This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com-
pressed air to avoid damaging it.
• The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
● V-belt case air filter
• The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
● V-belt
• The V-belt should be checked at the initial 8000 km (5000 mi) and every 4000 km (2500 mi) thereafter. Replace the
V-belt if any damage or excessive wear is found. The V-belt needs to be replaced every 25000 km (16000 mi) even
if there is no wear or damage.
● Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level. After dissembling the brake master cylinders and cal-
ipers, always change the brake fluid.
• Every two years replace the internal components of the brake master cylinder and caliper, and change the brake fluid.
7 • Replace the brake hose every four years and if cracked or damaged.
_

7-5
20BF8199E2.book Page 6 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU18712
2. Remove the screws, and then pull EAU19281

Removing and installing the panel off as shown.

Panel B
cowlings and panels
To remove the panel
3 1 4 Remove the screw, and then pull the
panel off as shown.
5

ZAUU0041

ZAUU0753 2 1. Panel A
2. Screw (✕ 3)
1. Panel A 4. Cowling A
2. Panel B 5. Cowling B To install the panel ZAUU0043

3. Panel C 1. Panel B
Place the panel in the original position,
2. Screw (✕ 1)
The cowlings and panels shown need and then install the screws.
7
to be removed to perform some of the
To install the panel
maintenance jobs described in this
Place the panel in the original position,
chapter. Refer to this section each time
and then install the screw.
a cowling or panel needs to be re-
moved and installed.

EAU19482

Panel A
ZAUU0042
To remove the panel
1. Open the seat. (See page 4-9.)
7-6
 20BF8199E2.book Page 7 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

To install the panel
1. Place the panel in the original po-
sition, and then install the screws.
1
3 2 2. Place the grab bar in the original
position, and then install the bolts.

Tightening torque:
Grab bar bolt:
ZAUU0044 ZAUU0045 1 10 Nm (1.0 m·kgf, 7.23 ft·lbf)
1. Bolt (✕ 4)
EAUU0510 EAUU0272
2. Panel C
Panel C Cowling A
3. Grab bar
3. Remove the screws, and then pull
To remove the panel To remove the cowling
the panel off as shown.
1. Open the seat. (See page 4-9.)
2. Remove the bolts, and then pull 1
the grab bar off as shown.
7 2

1 1 ZAUU0754
ZAUU0046
1. Cowling A
1. Screw (✕ 4)
2. Panel C 1. Remove the screws from cowling
B.

7-7
20BF8199E2.book Page 8 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

To install the cowling EAUT1835

1. Align the projections on cowling A Checking the spark plug

1 with the slots of cowling B, and The spark plug is an important engine
then push cowling A into the origi- component, which is easy to check.
nal position. Since heat and deposits will cause any
2. Install cowling B by installing the spark plug to slowly erode, the spark
screws. plug should be removed and checked
2
in accordance with the periodic mainte-
ZAUU0755 nance and lubrication chart. In addition,
1. Screw (✕ 2)
the condition of the spark plug can re-
2. Cowling B veal the condition of the engine.
2. Pull cowling A off as shown.
To remove the spark plug
1. Place the vehicle on the center-
stand.
ZAUU0757 2. Remove panel A and B. (See page
7-6.) 7
TIP 3. Remove the spark plug cap.
_

When installing cowling A, push in on

the areas shown from bottom to top.
_

ZAUU0756

TIP
When removing cowling A, pull out on
the areas shown from top to bottom.
_

ZAUU0578

1. Spark plug cap

7-8
 20BF8199E2.book Page 9 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

4. Remove the spark plug as shown, 2. Check the spark plug for electrode 2. Clean the surface of the spark
with the spark plug wrench includ- erosion and excessive carbon or plug gasket and its mating sur-
ed in the owner’s tool kit. other deposits, and replace it if face, and then wipe off any grime
necessary. from the spark plug threads.
3. Install the spark plug with the
Specified spark plug: spark plug wrench, and then tight-
C6HSA (NGK) or U20FS-U (DENSO) en it to the specified torque.

To install the spark plug Tightening torque:

1. Measure the spark plug gap with a Spark plug:
wire thickness gauge and, if nec- 15 Nm (1.5 m·kgf, 11 ft·lbf)
ZAUU0579
essary, adjust the gap to specifica-
1. Spark plug wrench TIP
tion. _

If a torque wrench is not available when

To check the spark plug installing a spark plug, a good estimate
1. Check that the porcelain insulator of the correct torque is 1/4–1/2 turn
around the center electrode of the past finger tight. However, the spark
7
spark plug is a medium-to-light tan plug should be tightened to the speci-
(the ideal color when the vehicle is fied torque as soon as possible.
ridden normally). _

1 4. Install the spark plug cap.

TIP
_

5. Install the panel.

If the spark plug shows a distinctly dif- ZAUU0703

ferent color, the engine could be oper- 1. Spark plug gap

ating improperly. Do not attempt to
diagnose such problems yourself. In- Spark plug gap:
stead, have a Yamaha dealer check 0.6–0.7 mm (0.024–0.028 in)
the vehicle.
_

7-9
20BF8199E2.book Page 10 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU0343

Engine oil and oil strainer

The engine oil level should be checked
before each ride. In addition, the oil 1
must be changed and the oil strainer
cleaned at the intervals specified in the
periodic maintenance and lubrication
chart.
ZAUU0758 ZAUU0054
To check the engine oil level 1. Oil filler cap 1. Dipstick
1. Place the vehicle on the center- EWAU0030 2. Maximum level mark
stand. A slight tilt to the side can WARNING 3. Minimum level mark
_

result in a false reading. The muffler and muffler protector 4. If the engine oil is at or below the
2. Start the engine, warm it up for become very hot during use. To minimum level mark, add sufficient
several minutes, and then turn it avoid possible burns, let the muffler oil of the recommended type to
off. and protector cool before removing raise it to the correct level.
3. Wait a few minutes until the oil set- the oil filler cap. 5. Insert the dipstick into the oil filler 7
tles, remove the oil filler cap, wipe _
hole, and then tighten the oil filler
the dipstick clean, insert it back TIP
_
cap.
into the oil filler hole (without The engine oil should be between the
screwing it in), and then remove it minimum and maximum level marks. To change the engine oil and clean
again to check the oil level.
_

the oil strainer

1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
7-10
 20BF8199E2.book Page 11 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

TIP
_

2 1 Make sure that the O-ring is properly

seated.
_

Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m·kgf, 14 ft·lbf)
Engine oil drain bolt B:
ZAUU0055 ZAUU0056
20 Nm (2.0 m·kgf, 14 ft·lbf)
1. Engine oil drain bolt A 1. Oil strainer
7. Refill with the specified amount of
2. Engine oil drain bolt B 2. Compression spring
the recommended engine oil, and
3. Remove the engine oil filler cap 3. O-ring
then install and tighten the oil filler
and drain bolt B to drain the oil TIP
_ cap.
from the crankcase. NOTICE: When only changing the engine oil, re-
When removing the engine oil move drain bolt A. When changing the Recommended engine oil:
drain bolt, the O-ring, compres- engine oil and cleaning the engine oil Engine oil brand:
7 sion spring, and oil strainer will strainer, remove drain bolt B also. YAMALUBE
fall out. Take care not to lose _
Engine oil type:
4. Clean the engine oil strainer with See page 9-1.
these parts. [ECA11001]
solvent, and then check it for dam- Oil quantity:
age and replace it if necessary. 0.8 L (0.85 US qt, 0.70 Imp.qt)
5. Check the O-ring for damage and
replace it if necessary. TIP
_

6. Install the engine oil strainer, com- Be sure to wipe off spilled oil on any
pression spring, O-ring and engine parts after the engine and exhaust sys-
oil drain bolt, and then tighten the tem have cooled down.
_

drain bolt to the specified torque.

7-11
20BF8199E2.book Page 12 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

ECA11620 EAU20065
3. Place an oil pan under the final
NOTICE Final transmission oil transmission case to collect the
_

● In order to prevent clutch slip- used oil.

page (since the engine oil also 4. Remove the final transmission oil
lubricates the clutch), do not filler cap and its O-ring from the fi-
mix any chemical additives. Do nal transmission case.
not use oils with a diesel speci- 5. Remove the final transmission oil
fication of “CD” or oils of a drain bolt and its gasket to drain
higher quality than specified. In the oil from the final transmission
addition, do not use oils labeled ZAUU0057 case.
“ENERGY CONSERVING II” or 1. Final transmission oil filler cap
higher.
The final transmission case must be
● Make sure that no foreign mate-
checked for oil leakage before each
rial enters the crankcase.
_
ride. If any leakage is found, have a
8. Start the engine, and then let it idle Yamaha dealer check and repair the
for several minutes while checking scooter. In addition, the final transmis-
7
it for oil leakage. If oil is leaking, sion oil must be changed as follows at
immediately turn the engine off the intervals specified in the periodic ZAUU0058

and check for the cause. maintenance and lubrication chart. 1. Final transmission oil drain bolt
9. Turn the engine off, and then 1. Start the engine, warm up the final 6. Install the final transmission oil
check the oil level and correct it if transmission oil by riding the drain bolt and its new gasket, and
necessary. scooter for several minutes, and then tighten the bolt to the speci-
then stop the engine. fied torque.
2. Place the scooter on the center-
stand.

7-12
 20BF8199E2.book Page 13 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU1270
3. Replace the air filter element by
Tightening torque: Air filter and V-belt case air pulling it out.
Final transmission oil drain bolt:
22 Nm (2.2 m·kgf, 16 ft·lbf)
filter elements
The air filter element should be re-
7. Refill with the specified amount of placed at every 16000 km (10000 mi)
the recommended final transmis- and the V-belt case air filter element
sion oil. WARNING! Make sure should be cleaned at the intervals
that no foreign material enters specified in the periodic maintenance
the final transmission case. and lubrication chart. Service the air fil-
Make sure that no oil gets on ter elements more frequently if you are
ZAUU0068
the tire or wheel. [EWA11311] riding in unusually wet or dusty areas.
1. Air filter element (wet type)

Recommended final transmission oil: Replacing the air filter element 4. Place a new air filter element in the
See page 9-1. 1. Place the vehicle on the center- original position.
Oil quantity: stand. 5. Install the air filter case cover by
0.10 L (0.11 US qt, 0.09 Imp.qt)
2. Remove the air filter case cover by installing the screws.
7 8. Install the final transmission oil fill- removing the screws.
er cap and its new O-ring, and Cleaning the V-belt case air filter
then tighten the oil filler cap. element
9. Check the final transmission case 1. Place the vehicle on the center-
for oil leakage. If oil is leaking, stand.
check for the cause. 2. Remove the V-belt air filter case
assembly by removing the bolts
and loosening the screw clamp.

ZAUU0067

1. Air filter case cover

2. Screw (✕ 4)
7-13
20BF8199E2.book Page 14 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

ZAUU0069 ZAUU0071 ZAUU0072

1. V-belt case air filter cover 1. V-belt air filter element

TIP
2. Bolt (✕ 2) 5. Clean the element with solvent,
_

The element should be wet but not

3. Clamp and then squeeze the remaining dripping.
3. Remove the V-belt air filter case solvent out. _

cover by removing the bolts. 6. Check the element for damage

Recommended oil:
and replace it if necessary. Yamaha foam air filter oil or other
7. Apply oil of the recommended type quality foam air filter oil
to the entire surface of the ele- 7
ment, and then squeeze the ex- 8. Install the element into the filter
cess oil out. WARNING! Use only case.
a dedicated parts cleaning sol- 9. Place the air filter case cover in its
vent. To avoid the risk of fire or original position, and then install
explosion, do not use gasoline the bolts and tighten the screw
ZAUU0070
or solvents with a low flash clamp. NOTICE: Make sure that
1. V-belt case air filter inner cover
point. [EWA10431] NOTICE: To avoid each filter element is properly
2. Bolt (✕ 4)
damaging the air filter element, seated in its case. The engine
4. Remove the V-belt case air filter should never be operated with-
handle it gently and carefully,
element by pulling it out. out the filter elements installed,
and do not twist it. [ECA10521]
7-14
 20BF8199E2.book Page 15 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

otherwise the piston(s) and/or EAU21280

cylinder(s) may become exces- Adjusting the carburetor

sively worn. [ECA10531] The carburetor is an important part of
the engine and requires very sophisti-
Cleaning the air filter caps and cated adjustment. Therefore, most car-
check hose buretor adjustments should be left to a
1. Check each cap at the bottom left Yamaha dealer, who has the neces-
side of the air filter case and the sary professional knowledge and expe-
hose at the bottom of the V-belt ZAUU0074 rience. The adjustment described in
case for accumulated dirt or water. 1. Air filter check hose the following section, however, may be
2. If dirt or water is visible, remove serviced by the owner as part of routine
the hose or caps from their clamp. maintenance.
ECA10550
3. Drain dirt or water into a proper
NOTICE
container. _

The carburetor has been set and ex-

4. Install the air filter check hose or
tensively tested at the Yamaha fac-
caps to the original position.
7 tory. Changing these settings
TIP
_
without sufficient technical knowl-
ZAUU0073 The air filter check hose or caps need edge may result in poor perfor-
1. Air filter cap more frequent cleaning after riding in mance of or damage to the engine.
the rain, washing the vehicle, or in case _

of overturn. If the check hose or caps

are clogged, have a Yamaha dealer
service the vehicle.
_

7-15
20BF8199E2.book Page 16 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU0321
5. Remove the rubber cap and insert
Adjusting the engine idling a Phillips screwdriver into the
Engine idling speed:
1500–1700 r/min
speed throttle stop screw hole.
The engine idling speed must be TIP
_

checked and, if necessary, adjusted as If the specified idling speed cannot be

follows at the intervals specified in the obtained as described above, have a
periodic maintenance and lubrication Yamaha dealer make the adjustment.
chart. _

ECAU0040
The engine should be warm before
NOTICE
making this adjustment. _

The engine idling speed should be

TIP
_
ZAUU0075 adjusted to specification. If the idle
● The engine is warm when it quick- 1. Rubber cap speed is too low, the engine may be
ly responds to the throttle. 6. To increase the engine idling hard to start. If the idle speed is too
● A diagnostic tachometer is needed high, fuel consumption will in-
speed, turn the screw in direction
to make this adjustment. (a). To decrease the engine idling crease. Always adjust the engine
1. Open the seat. (See page 4-9 for speed, turn the screw in direction idling speed when the engine is 7
seat opening and closing proce- (b). warm.
_

dures.) 7. Install the panel and close the

2. Remove panel A. (See page 7-6 seat.
for panel removal and installation
procedures.)
3. Attach the tachometer to the spark
plug lead.
4. Check the engine idling speed
and, if necessary, adjust it to spec-
ZAUU0076
ification as follows. 1. Throttle stop screw
7-16
 20BF8199E2.book Page 17 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU21374
2. To increase the throttle grip free EAU21401

Adjusting the throttle grip free play, turn the throttle grip free play Valve clearance
play adjusting nut in direction (a). To The valve clearance changes with use,
decrease the throttle grip free play, resulting in improper air-fuel mixture
turn the adjusting nut in direction and/or engine noise. To prevent this
(b). from occurring, the valve clearance
3. Tighten the locknut. must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

ZAUU0077

1. Throttle grip free play adjusting nut

2. Locknut
3. Cable cover
c. Throttle grip free play

The throttle grip free play should mea-

7
sure 3.0–7.0 mm (0.12–0.28 in) as
shown. Periodically check the throttle
grip free play and, if necessary, adjust it
as follows.

TIP
_

The engine idling speed must be cor-

rectly adjusted before checking and ad-
justing the throttle grip free play.
_

1. Loosen the locknut.

7-17
20BF8199E2.book Page 18 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU0714
weight of rider, passenger, car- Tire inspection
Tires go, and accessories approved
To maximize the performance, durabil- for this model. C
ity, and safe operation of your motorcy- _

cle, note the following points regarding

Tire air pressure (measured on cold
the specified tires. tires):
Up to 90 kg (198 lb): A B
Tire air pressure Front:
The tire air pressure should be 200 kPa (2.00 kgf/cm2, 29 psi)
checked and, if necessary, adjusted Rear: ZAUU0743

before each ride. 225 kPa (2.25 kgf/cm2, 33 psi) A. Tire sidewall
EWA10503
90 kg (198 lb) to maximum load: B. Tire wear indicator
Front: C. Tire tread depth
WARNING 200 kPa (2.00 kgf/cm2, 29 psi)
The tires must be checked before each
_

Operation of this vehicle with im- Rear:

proper tire pressure may cause se- 225 kPa (2.25 kgf/cm2, 33 psi) ride. If the tire shows crosswise lines B
vere injury or death from loss of Maximum load*: (minimum tread depth), if the tire has a
control. 163 kg (359 lb) nail or glass fragments in it, or if the
* Total weight of rider, passenger, 7
● The tire air pressure must be sidewall is cracked, have a Yamaha
cargo and accessories
checked and adjusted on cold dealer replace the tire immediately.
tires (i.e., when the temperature EWA10511

of the tires equals the ambient WARNING Minimum tire tread depth (front and
_
rear):
temperature). Never overload your vehicle. Opera-
1.0 mm (0.04 in)
● The tire air pressure must be tion of an overloaded vehicle could
adjusted in accordance with the cause an accident. TIP
_

riding speed and with the total

_

The tire tread depth limits may differ

from country to country. Always comply
with the local regulations.
_

7-18
 20BF8199E2.book Page 19 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

Tire information EWA10562 EAU21943

This motorcycle is equipped with tube WARNING Spoke wheels EWA10610

_

tires. ● It is dangerous to ride with a WARNING

EWA10461
worn-out tire. When a tire tread _

The wheels on this model are not de-

WARNING begins to show crosswise lines,
_
signed for use with tubeless tires.
The front and rear tires should be of have a Yamaha dealer replace
Do not attempt to use tubeless tires
the same make and design, other- the tire immediately.
on this model.
wise the handling characteristics of ● The replacement of all wheel _

the vehicle may be different, which and brake-related parts, includ- To maximize the performance, durabil-
could lead to an accident. ing the tires, should be left to a ity, and safe operation of your motorcy-
_

Yamaha dealer, who has the cle, note the following points regarding
After extensive tests, only the tires list- the specified wheels.
necessary professional knowl-
ed below have been approved for this
edge and experience. ● The wheel rims should be checked
model by Yamaha Motor Co., Ltd.
● It is not recommended to patch for cracks, bends, warpage or oth-
Front tire: a punctured tube. If unavoid- er damage, and the spokes for
Size: able, however, patch the tube looseness or damage before each
70/90-14M/C 34P very carefully and replace it as ride. If any damage is found, have
7 Manufacturer/model: soon as possible with a high- a Yamaha dealer replace the
IRC/NF59, Vee Rubber/V282F quality product. wheel. Do not attempt even the
Rear tire: smallest repair to the wheel. A de-
● Ride at moderate speeds after
Size:
changing a tire since the tire formed or cracked wheel must be
80/90-14M/C 40P
surface must first be “broken replaced.
Manufacturer/model:
in” for it to develop its optimal ● The wheel should be balanced
IRC/NR76, Vee Rubber/V282R
characteristics. whenever either the tire or wheel
_
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.
7-19
20BF8199E2.book Page 20 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU37913 EAU22170

Checking the brake lever free Adjusting the rear brake lever
play free play

ZAUU0082

1. Rear brake lever free play adjusting nut

EWA10650
ZAUU0079 ZAUU0081
WARNING
There should be no free play at the 1. Rear brake lever free play _

If proper adjustment cannot be ob-

brake lever end. If there is free play, The brake lever free play should mea- tained as described, have a Yamaha
have a Yamaha dealer inspect the sure 10.0–20.0 mm (0.39–0.79 in) as dealer make this adjustment.
brake system. shown. Periodically check the brake le- _

EWA14211
ver free play and, if necessary, adjust it 7
WARNING
_
as follows.
A soft or spongy feeling in the brake
To increase the brake lever free play,
lever can indicate the presence of
turn the adjusting nut at the brake shoe
air in the hydraulic system. If there
is air in the hydraulic system, have a plate in direction (a). To decrease the
Yamaha dealer bleed the system be- brake lever free play, turn the adjusting
fore operating the vehicle. Air in the nut in direction (b).
hydraulic system will diminish the
braking performance, which may re-
sult in loss of control and an acci-
dent.
_

7-20
 20BF8199E2.book Page 21 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU22380
peared, have a Yamaha dealer replace EAUU0830

Checking the front brake pads the brake pads as a set. Checking the brake fluid level
and rear brake shoes
The front brake pads and the rear EAU22540

brake shoes must be checked for wear Rear brake shoes

at the intervals specified in the periodic
maintenance and lubrication chart.

EAU22430

Front brake pads

ZAUU0086

1. Minimum level mark

Insufficient brake fluid may allow air to

ZAUU0161
enter the brake system, possibly caus-
1. Brake shoe wear indicator
ing it to become ineffective.
2. Brake shoe wear limit line
Before riding, check that the brake fluid
The rear brake is provided with a wear is above the minimum level mark and
7 indicator, which allows you to check the replenish if necessary. A low brake flu-
ZAUU0083
brake shoe wear without having to dis- id level may indicate worn brake pads
1. Brake pad wear indicator groove (✕ 2)
assemble the brake. To check the and/or brake system leakage. If the
Each front brake pad is provided with brake shoe wear, check the position of brake fluid level is low, be sure to check
wear indicator grooves, which allow the wear indicator while applying the the brake pads for wear and the brake
you to check the brake pad wear with- brake. If a brake shoe has worn to the system for leakage.
out having to disassemble the brake. point that the wear indicator reaches Observe these precautions:
To check the brake pad wear, check the wear limit line, have a Yamaha ● When checking the fluid level,
the wear indicator grooves. If a brake dealer replace the brake shoes as a make sure that the top of the mas-
pad has worn to the point that the wear ter cylinder is level by turning the
set.
indicator grooves have almost disap- handlebars.
7-21
20BF8199E2.book Page 22 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

● Use only the recommended quali- EAU22721 EAUU0310

ty brake fluid, otherwise the rubber Changing the brake fluid Checking the V-belt
seals may deteriorate, causing Have a Yamaha dealer change the The V-belt must be checked and re-
leakage and poor braking perfor- brake fluid at the intervals specified in placed by a Yamaha dealer at the inter-
mance. the TIP after the periodic maintenance vals specified in the periodic
and lubrication chart. In addition, have maintenance and lubrication chart.
Recommended brake fluid: the oil seals of the brake master cylin-
YAMAHA GENUINE BRAKE FLUID der and caliper as well as the brake
or equivalent DOT3 or DOT4 hose replaced at the intervals listed be-
low or whenever they are damaged or
● Refill with the same type of brake leaking.
fluid. Mixing fluids may result in a ● Oil seals: Replace every two
harmful chemical reaction and years.
lead to poor braking performance. ● Brake hose: Replace every four
● Be careful that water does not en- years.
ter the master cylinder when refill-
ing. Water will significantly lower
the boiling point of the fluid and 7
may result in vapor lock.
● Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.
● As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.
7-22
 20BF8199E2.book Page 23 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU23095 EAU23114 EAU43641

Checking and lubricating the Checking and lubricating the Lubricating the front and rear
cables throttle grip and cable brake levers
The operation of all control cables and The operation of the throttle grip should
the condition of the cables should be be checked before each ride. In addi- Front brake
checked before each ride, and the ca- tion, the cable should be lubricated by
bles and cable ends should be lubricat- a Yamaha dealer at the intervals spec-
ed if necessary. If a cable is damaged ified in the periodic maintenance chart.
or does not move smoothly, have a The throttle cable is equipped with a
Yamaha dealer check or replace it. rubber cover. Make sure that the cover
WARNING! Damage to the outer is securely installed. Even though the
housing of cables may result in in- cover is installed correctly, it does not
ternal rusting and cause interfer- completely protect the cable from water
ZAUU0759
ence with cable movement. Replace entry. Therefore, use care not to pour
damaged cables as soon as possi- water directly onto the cover or cable
ble to prevent unsafe conditions. when washing the vehicle. If the cable Rear brake
7 [EWA10711] or cover becomes dirty, wipe clean with
a moist cloth.
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil

ZAUU0760

7-23
20BF8199E2.book Page 24 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

The pivoting points of the front and rear EAU23213

brake levers must be lubricated at the Checking and lubricating the Recommended lubricant:
Lithium-soap-based grease
intervals specified in the periodic main- centerstand and sidestand
tenance and lubrication chart.

Recommended lubricants:
Front brake lever:
Silicone grease
Rear brake lever:
Lithium-soap-based grease

ZAUU0089

The operation of the centerstand and

sidestand should be checked before
each ride, and the pivots and metal-to-
metal contact surfaces should be lubri-
cated if necessary. 7
EWA10741

_
WARNING
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or re-
pair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
_

7-24
 20BF8199E2.book Page 25 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU23272 EAU23283

Checking the front fork Checking the steering

The condition and operation of the front Worn or loose steering bearings may
fork must be checked as follows at the cause danger. Therefore, the operation
intervals specified in the periodic main- of the steering must be checked as fol-
tenance and lubrication chart. lows at the intervals specified in the pe-
riodic maintenance and lubrication
To check the condition chart.
Check the inner tubes for scratches, ZAUU0761 1. Place a stand under the engine to
damage and excessive oil leakage. ECA10590 raise the front wheel off the
NOTICE ground. (See page 7-24 for more
To check the operation _

information.) WARNING! To
If any damage is found or the front
1. Place the vehicle on a level sur- avoid injury, securely support
fork does not operate smoothly,
face and hold it in an upright posi- the vehicle so there is no dan-
have a Yamaha dealer check or re-
tion. WARNING! To avoid injury, ger of it falling over. [EWA10751]
pair it.
securely support the vehicle so _

7 there is no danger of it falling

over. [EWA10751]
2. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
ZAUU0091

7-25
20BF8199E2.book Page 26 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

2. Hold the lower ends of the front EAU23291 EAUU0921

fork legs and try to move them for- Checking the wheel bearings Battery
ward and backward. If any free The front and rear wheel bearings must This model is equipped with a VRLA
play can be felt, have a Yamaha be checked at the intervals specified in (Valve Regulated Lead Acid) battery.
dealer check or repair the steering. the periodic maintenance and lubrica- There is no need to check the electro-
tion chart. If there is play in the wheel lyte or to add distilled water. However,
hub or if the wheel does not turn the battery lead connections need to be
smoothly, have a Yamaha dealer checked and, if necessary, tightened.
check the wheel bearings.

ZAUU0092

1. Negative battery lead 7

2. Battery band
3. Positive battery lead
4. Battery cover
EWA10760

_
WARNING
● Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-

7-26
 20BF8199E2.book Page 27 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

ways shield your eyes when To charge the battery 2. If the battery will be stored for
working near batteries. In case Have a Yamaha dealer charge the bat- more than two months, check it at
of contact, administer the fol- tery as soon as possible if it seems to least once a month and fully
lowing FIRST AID. have discharged. Keep in mind that the charge it if necessary.
• EXTERNAL: Flush with plenty battery tends to discharge more quickly 3. Fully charge the battery before in-
of water. if the vehicle is equipped with optional stallation. NOTICE: When install-
• INTERNAL: Drink large quan- electrical accessories. ing the battery, be sure the key
tities of water or milk and im- ECA16521
is turned to “OFF”, then con-
mediately call a physician. NOTICE nect the positive lead before
_

• EYES: Flush with water for 15 To charge a VRLA (Valve Regulated connecting the negative lead.
minutes and seek prompt Lead Acid) battery, a special (con- [ECA16840]

medical attention. stant-voltage) battery charger is re- 4. After installation, make sure that
● Batteries produce explosive hy- quired. Using a conventional battery the battery leads are properly con-
drogen gas. Therefore, keep charger will damage the battery. nected to the battery terminals.
sparks, flames, cigarettes, etc., _

ECA16530
away from the battery and pro-
To store the battery NOTICE
vide sufficient ventilation when _

1. If the vehicle will not be used for Always keep the battery charged.
7 charging it in an enclosed
more than one month, remove the Storing a discharged battery can
space.
battery, fully charge it, and then cause permanent battery damage.
● KEEP THIS AND ALL BATTER-
place it in a cool, dry place. NO- _

IES OUT OF THE REACH OF TICE: When removing the bat-

ECAU0050

CHILDREN. tery, be sure the key is turned to NOTICE

_
_

ECA10620
“OFF”, then disconnect the Do not ride the vehicle with the bat-
NOTICE negative lead before discon- tery disconnected or with a low-
_

Never attempt to remove the battery necting the positive lead. [ECA16302] charged battery. This will cause
cell seals, as this would permanent- hard engine starting, decreased
ly damage the battery. headlight life, and the flasher lights
_ may not operate properly.
_

7-27
20BF8199E2.book Page 28 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU23482 EAUU0930

Replacing the fuse Replacing a headlight bulb

If a headlight bulb burns out, replace it
as follows.
ECA10660

NOTICE
_

Do not touch the glass part of the

headlight bulb to keep it free from
ZAUU0094
oil, otherwise the transparency of
1. Fuse the glass, the luminosity of the bulb,
ZAUU0093
and the bulb life will be adversely af-
1. Battery band 2. Remove the blown fuse, and then
fected. Thoroughly clean off any dirt
2. Battery cover install a new fuse of the specified
and fingerprints on the headlight
3. Spare fuse amperage. WARNING! Do not
bulb using a cloth moistened with
use a fuse of a higher amperage
The fuse holder is located under the alcohol or thinner.
rating than recommended to
seat. (See page 4-9.) _

avoid causing extensive dam-

If the fuse is blown, replace it as fol-
age to the electrical system and 7
lows.
possibly a fire. [EWA15131]
1. Turn the key to “OFF” and turn off
all electrical circuits.
Specified fuse:
10.0 A

3. Turn the key to “ON” and turn on

the electrical circuits to check if the
devices operate.
1. Do not touch the glass part of the bulb.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
7-28
 20BF8199E2.book Page 29 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

1. Remove cowling A. (See page ECAU0070 EAUU0940

7-7.) NOTICE Replacing a front turn signal

_

If a headlight bulb of different watt- light bulb or an auxiliary light

age than recommended is used, it bulb
may cause the battery to discharge If a front turn signal light or an auxiliary
or affect the headlight lighting. light bulb burns out, replace it as fol-
lows.
_

4. Install the cowling.

1. Remove cowling A. (See page
5. Have a Yamaha dealer adjust the
7-7.)
headlight beam if necessary.
2. Remove the socket (together with
ZAUU0762
the bulb) by turning it counter-
1. Cowling A
clockwise.
2. Remove the headlight bulb holder
by pushing it inward and turning it
counterclockwise, and then re-
move the burnt out bulb.
7 3. Place a new bulb into position, and
then secure it with the bulb holder.

ZAUU0097

1. Front turn signal light bulb socket

2. Auxiliary light bulb socket

3. Remove the burnt out bulb by pull-

ing it out.
ZAUU0096

1. Headlight bulb holder

7-29
20BF8199E2.book Page 30 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAUU1250
4. Remove the burnt-out bulb from
Replacing the tail/brake light the socket by pushing it in and
bulb or a rear turn signal light turning it counterclockwise.
bulb
Place the vehicle on the centerstand.

Tail/brake light bulb

1. Open the seat. (See page 4-9 for
ZAUU0098 seat opening and closing proce-
1. Front turn signal light bulb dures.)
2. Auxiliary light bulb 2. Remove panel C. (See page 7-7
ZAUU0100
4. Insert a new bulb into the socket. for panel removing and installing
ECAU0080 1. Tail/brake light bulb
procedures.)
NOTICE 3. Remove the tail/brake light bulb 5. Insert a new bulb into the socket,
_

If a turn signal light bulb of different socket by turning it counterclock- push it in, and then turn it clock-
wattage than recommended is used, wise. wise until it stops.
ECAU0090
the turn signal light flashing may be 7
affected. NOTICE
_

_
If a taillight bulb of different wattage
5. Install the socket (together with the
than recommended is used, it may
bulb) by turning it clockwise.
cause the battery to discharge or af-
6. Install the cowlings.
fect the taillight lighting.
_

6. Install the socket into its original

ZAUU0099
position.
1. Tail/brake light bulb socket 7. Install the panel, and then securely
close the seat.

7-30
 20BF8199E2.book Page 31 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

Turn signal light bulb EAU25851

1. Open the seat. (See page 4-9 for Troubleshooting

seat opening and closing proce- Although Yamaha motorcycles receive
dures.) a thorough inspection before shipment
2. Remove panel C. (See page 7-7 from the factory, trouble may occur dur-
for panel removing and installing ing operation. Any problem in the fuel,
procedures.) compression, or ignition systems, for
3. Remove the turn signal light bulb example, can cause poor starting and
socket by turning it counterclock- ZAUU0102 loss of power.
wise. 1. Rear turn signal light bulb (✕ 2) The following troubleshooting chart
5. Insert a new bulb into the socket. represents a quick and easy procedure
ECAU0080 for checking these vital systems your-
NOTICE self. However, should your motorcycle
_

If a turn signal light bulb of different require any repair, take it to a Yamaha
wattage than recommended is used, dealer, whose skilled technicians have
the turn signal light flashing may be the necessary tools, experience, and
7 affected. know-how to service the motorcycle
_
properly.
ZAUU0101 6. Install the socket into its original
Use only genuine Yamaha replace-
1. Rear turn signal light bulb socket (✕ 2) position.
ment parts. Imitation parts may look
7. Install the panel, and then securely
4. Remove the burnt-out bulb from like Yamaha parts, but they are often
close the seat.
the socket by pulling it out. inferior, have a shorter service life and
can lead to expensive repair bills.

7-31
20BF8199E2.book Page 32 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EWA15141

_
WARNING
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or
property damage.
_

7-32
 20BF8199E2.book Page 33 Monday, February 28, 2011 10:46 AM

PERIODIC MAINTENANCE AND ADJUSTMENT

EAU25903

Troubleshooting chart
1. Fuel
There is enough fuel. Check the compression.
Check the fuel level in
the fuel tank.
The engine does not start.
There is no fuel. Supply fuel.
Check the compression.

2. Compression
There is compression. Check the ignition.
Operate the electric starter.
Have a Yamaha dealer
There is no compression.
check the vehicle.

3. Ignition Wipe off with a dry cloth and correct the Open the throttle halfway and operate
Wet
spark plug gap, or replace the spark plug. the electric starter.
Remove the spark plug
and check the electrodes.
The engine does not start.
Dry Have a Yamaha dealer check the vehicle.
Check the battery.
7
4. Battery The engine turns over
The battery is good.
quickly. The engine does not start.
Operate the electric starter. Have a Yamaha dealer
Check the battery lead connections, check the vehicle.
The engine turns over
and have a Yamaha dealer charge
slowly.
the battery if necessary.

7-33
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

EAU25981 MOTORCYCLE CARE AND STORAGE

EAUU0405
3. Remove extremely stubborn dirt, ter to clean plastic. However, if
Care like oil burnt onto the crankcase, the plastic parts cannot be thor-
While the open design of a motorcycle with a degreasing agent and a oughly cleaned with water, di-
reveals the attractiveness of the tech- brush, but never apply such prod- luted mild detergent with water
nology, it also makes it more vulnera- ucts onto seals, gaskets and may be used. Be sure to rinse
ble. Rust and corrosion can develop wheel axles. Always rinse the dirt off any detergent residue using
even if high-quality components are and degreaser off with water. plenty of water, as it is harmful
used. A rusty exhaust pipe may go un- to plastic parts.
noticed on a car, however, it detracts Cleaning ● Do not use any harsh chemical
from the overall appearance of a mo- ECA10783
products on plastic parts. Be
torcycle. Frequent and proper care NOTICE sure to avoid using cloths or
_

does not only comply with the terms of ● Avoid using strong acidic wheel sponges which have been in
the warranty, but it will also keep your cleaners, especially on spoked contact with strong or abrasive
motorcycle looking good, extend its life wheels. If such products are cleaning products, solvent or
and optimize its performance. used on hard-to-remove dirt, do thinner, fuel (gasoline), rust re-
not leave the cleaner on the af- movers or inhibitors, brake flu-
Before cleaning fected area any longer than in- id, antifreeze or electrolyte.
1. Cover the muffler outlet with a structed. Also, thoroughly rinse ● Do not use high-pressure wash-
plastic bag after the engine has the area off with water, immedi- 8
ers or steam-jet cleaners since
cooled down. ately dry it, and then apply a they cause water seepage and
2. Make sure that all caps and covers corrosion protection spray. deterioration in the following ar-
as well as all electrical couplers ● Improper cleaning can damage eas: seals (of wheel and swing-
and connectors, including the plastic parts (such as cowlings, arm bearings, fork and brakes),
spark plug cap, are tightly in- panels, windshields, headlight electric components (couplers,
stalled. lenses, meter lenses, etc.) and connectors, instruments,
the mufflers. Use only a soft, switches and lights), breather
clean cloth or sponge with wa- hoses and vents.
8-1
 20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

MOTORCYCLE CARE AND STORAGE

● For vehicles equipped with a After riding in the rain or near the sea 3. To prevent corrosion, it is recom-
windshield: Do not use strong Since sea salt is extremely corrosive mended to apply a corrosion pro-
cleaners or hard sponges as carry out the following steps after each tection spray on all metal,
they will cause dulling or ride in the rain or near the sea. including chrome- and nickel-plat-
scratching. Some cleaning 1. Clean the motorcycle with cold ed, surfaces.
compounds for plastic may water and a mild detergent after 4. Use spray oil as a universal clean-
leave scratches on the wind- the engine has cooled down. er to remove any remaining dirt.
shield. Test the product on a NOTICE: Do not use warm wa- 5. Touch up minor paint damage
small hidden part of the wind- ter since it increases the corro- caused by stones, etc.
shield to make sure that it does sive action of the salt. [ECA10791] 6. Wax all painted surfaces.
not leave any marks. If the wind- 2. Apply a corrosion protection spray 7. Let the motorcycle dry completely
shield is scratched, use a quali- on all metal, including chrome- before storing or covering it.
ty plastic polishing compound and nickel-plated, surfaces to pre- EWA10942

after washing. vent corrosion. _

WARNING
_
Contaminants on the brakes or tires
After normal use After cleaning can cause loss of control.
Remove dirt with warm water, a mild 1. Dry the motorcycle with a chamois ● Make sure that there is no oil or

detergent, and a soft, clean sponge, or an absorbing cloth. wax on the brakes or tires. If
8 and then rinse thoroughly with clean 2. Use a chrome polish to shine necessary, clean the brake
water. Use a toothbrush or bottlebrush chrome, aluminum and stainless- discs and brake linings with a
for hard-to-reach areas. Stubborn dirt steel parts, including the exhaust regular brake disc cleaner or ac-
and insects will come off more easily if system. (Even the thermally in- etone, and wash the tires with
the area is covered with a wet cloth for duced discoloring of stainless- warm water and a mild deter-
a few minutes before cleaning. steel exhaust systems can be re- gent.
moved through polishing.)

8-2
20BF8199E2.book Page 3 Monday, February 28, 2011 10:46 AM

MOTORCYCLE CARE AND STORAGE

● Before operating the vehicle, EAU26303
1. Follow all the instructions in the
test its braking performance Storage “Care” section of this chapter.
and cornering behavior. 2. Drain the carburetor float chamber
Short-term
_

ECAU0020 by loosening the drain bolt; this will

Always store your scooter in a cool, dry prevent fuel deposits from building
NOTICE place and, if necessary, protect it
_

up. Pour the drained fuel into the

● Apply spray oil and wax spar- against dust with a porous cover. Be
fuel tank.
ingly and make sure to wipe off sure the engine and the exhaust sys- 3. Fill up the fuel tank and add fuel
any excess. tem are cool before covering the scoot- stabilizer (if available) to prevent
● Never apply oil or wax to any er.
the fuel tank from rusting and the
rubber parts, plastic parts or ECA10820
fuel from deteriorating.
headlight, taillight and meter NOTICE
_
4. Perform the following steps to pro-
lenses, but treat them with a ● Storing the scooter in a poorly
tect the cylinder, piston rings, etc.
suitable care product. ventilated room or covering it
from corrosion.
● Avoid using abrasive polishing with a tarp, while it is still wet,
a. Remove the spark plug cap and
compounds as they will wear will allow water and humidity to
spark plug.
away the paint. seep in and cause rust.
_ b. Pour a teaspoonful of engine oil
● To prevent corrosion, avoid
TIP into the spark plug bore.
_
damp cellars, stables (because
● Consult a Yamaha dealer for ad- c. Install the spark plug cap onto 8
of the presence of ammonia)
vice on what products to use. the spark plug, and then place
and areas where strong chemi-
● Washing, rainy weather or humid the spark plug on the cylinder
cals are stored.
climates can cause the headlight _
head so that the electrodes are
lens to fog. Turning the headlight grounded. (This will limit spark-
Long-term ing during the next step.)
on for a short period of time will
Before storing your scooter for several d. Turn the engine over several
help remove the moisture from the
months: times with the starter. (This will
lens.
_
coat the cylinder wall with oil.)
8-3
 20BF8199E2.book Page 4 Monday, February 28, 2011 10:46 AM

MOTORCYCLE CARE AND STORAGE

WARNING! To prevent dam- 8. Remove the battery and fully
age or injury from sparking, charge it. Store it in a cool, dry
make sure to ground the place and charge it once a month.
spark plug electrodes while Do not store the battery in an ex-
turning the engine over. cessively cold or warm place [less
[EWA10951] than 0 °C (30 °F) or more than
e. Remove the spark plug cap 30 °C (90 °F)]. For more informa-
from the spark plug, and then tion on storing the battery, see
install the spark plug and the page 7-27.
spark plug cap.
5. Lubricate all control cables and the TIP
_

Make any necessary repairs before

pivoting points of all levers and
storing the scooter.
pedals as well as of the side- _

stand/centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alterna-
8 tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
7. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.

8-4
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

EAU26321 SPECIFICATIONS
Dimensions: Engine oil: Spark plug gap:
Overall length: Recommended brand: 0.6–0.7 mm (0.02–0.03 in)
1830 mm (72.0 in) YAMALUBE Clutch:
Overall width: Type: Clutch type:
705 mm (27.8 in) YAMALUBE 4-AT SAE 20W-40 or Dry, centrifugal automatic
Overall height: SAE 10W-30 Transmission:
1050 mm (41.3 in) Recommended engine oil grade: Primary reduction ratio:
Seat height: API Service “SG” type or higher, JASO 1.000
745 mm (29.3 in) standard MA Final drive:
Wheelbase: Quantity (periodic oil change): Gear
1240 mm (48.8 in) 0.80 L (0.85 US qt) (0.70 Imp.qt) Secondary reduction ratio:
Ground clearance: Final transmission oil: 10.123 (47/15 ✕ 42/13)
125 mm (4.9 in) Type: Transmission type:
Minimum turning radius: YAMALUBE 4 or SAE 10W-40 “SE” type V-belt automatic
1800 mm (70.9 in) motor oil Chassis:
Weight: Quantity (periodic oil change): Frame type:
Curb weight: 0.10 L (0.11 US qt) (0.09 Imp.qt) Underbone steel tube
96.0 kg (212 lb) Air filter: Caster angle:
Maximum load: Air filter element: 26.5 °
163 kg (359 lb) Oil-coated paper element Trail:
Engine: Fuel: 100.0 mm (3.94 in)
Engine type: Recommended fuel: Front tire:
Air-cooled 4-stroke, SOHC Regular unleaded gasoline or gasohol Type:
Cylinder arrangement: (E10) (91 min. pump octane) Tube tire
Forward inclined single cylinder Fuel tank capacity: Size:
Displacement: 4.1 L (1.08 US gal) (0.90 Imp.gal) 70/90-14M/C 34P
114.0 cm3 (6.95 cu.in) Carburetor: Manufacturer/model:
Bore ✕ stroke: Manufacturer: IRC/NF59
50.0 ✕ 57.9 mm (1.97 ✕ 2.28 in) KEIHIN VEE RUBBER/V282F 9
Compression ratio: Model ✕ quantity: Rear tire:
8.80 :1 NCV24 ✕ 1 Type:
Starting system: Spark plug(s): Tube tire
Electric starter and kickstarter Manufacturer/model: Size:
Lubrication system: DENSO/U20FS-U 80/90-14M/C 40P
Wet sump NGK/C6HSA

9-1
 20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM

SPECIFICATIONS
Manufacturer/model: Front suspension: Rear turn signal light:
IRC/NR76 Type: 12 V, 10.0 W ✕ 2
VEE RUBBER/V282R Telescopic fork Auxiliary light:
Tire air pressure (measured on cold Spring/shock absorber type: 12 V, 3.4 W ✕ 1
tires): Coil spring/Oil damper Meter lighting:
Front: Wheel travel: 14 V, 1.4 W ✕ 1
200 kPa (29 psi) (2.00 kgf/cm2) 90.0 mm (3.54 in) High beam indicator light:
Rear: Rear suspension: 12 V, 1.7 W ✕ 1
Type: Turn signal indicator light:
225 kPa (33 psi) (2.25 kgf/cm2)
Unit swing 12 V, 1.7 W ✕ 1
Front wheel:
Spring/shock absorber type: Engine trouble warining light:
Wheel type:
Coil spring/Oil damper 12 V, 1.7 W ✕ 1
Spoke wheel
Rim size:
Wheel travel: Fuse:
80.0 mm (3.15 in) Main fuse:
14 ✕ 1.40
Rear wheel: Electrical system: 10.0 A
Ignition system:
Wheel type:
DC C.D.I.
Spoke wheel
Charging system:
Rim size:
AC magneto
14 ✕ 1.60
Front brake: Battery:
Model:
Type:
GTZ5S
Single disc brake
Voltage, capacity:
Operation:
12 V, 3.5 Ah
Right hand operation
Recommended fluid: Headlight:
Bulb type:
DOT 3 or 4
Krypton bulb
Rear brake:
Type: Bulb voltage, wattage ✕ quantity:
9 Headlight:
Drum brake
12 V, 32.0 W/32.0 W ✕ 1
Operation:
Tail/brake light:
Left hand operation
12 V, 5.0 W/21.0 W ✕ 1
Front turn signal light:
12 V, 10.0 W ✕ 2

9-2
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

EAU26344 CONSUMER INFORMATION

EAUV0090 EAU26410 EAUU1260

Identification numbers Vehicle identification number Engine serial number

Record the vehicle identification num- 1
ber and engine serial number in the
spaces provided below for assistance
when ordering spare parts from a
Yamaha dealer or for reference in case
the vehicle is stolen.
VEHICLE IDENTIFICATION NUM-
BER: ZAUU0104 ZAUU0105

1. Vehicle identification number 1. Engine serial number

The vehicle identification number is The engine serial number is stamped

stamped into the frame. on the top left side of the crankcase.

ENGINE SERIAL NUMBER: TIP

_

The vehicle identification number is

used to identify your motorcycle and
may be used to register your motorcy-
cle with the licensing authority in your
area.
_

10

10-1
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM
20BF8199E2.book Page 2 Monday, February 28, 2011 10:46 AM
20BF8199E2.book Page 1 Monday, February 28, 2011 10:46 AM

PRINTED IN THAILAND