MATERIAL SAFETY DATA SHEET
FLORGARD EPU SL PART B
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE
COMPANY/UNDERTAKING
Identification ofthe substanceorpreparation
Product name : FLORGARDEPUSLPartB
Use of the : F or floor coating
ubstance/preparation Application
Company/undertaking identification
Supplier : APURVA INDIA PRIVATE LIMITED
nd
New Udyog Mandir No.2,2 Floor,
Office No.2, 7C, Pitambar ane,
Mahim(w),Mumbai 400 016
Maharashtra, India
Tel.No. 91 22 24475051 Fax No. 91 22 24475056
2. HAZARDS IDENTIFICATION
Harmful by inhalation.
May cause sensitisation by inhalation and skin contact.
Irritating to eyes, respiratory system and skin.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance/preparation : Multi-constituent substance
Ingredient name CAS % Risk phrases
number
Benzyl Alcohol 100‐51‐6 > 5.0%
Bis (Dimethyl amino methyl) phenol 71074‐89‐0 <1.0%
Isophorone Diamine 2855‐13‐2 > 60% R21/22, 34, 42/43
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in
this section.
4. FIRST AID MEASURES
If inhaled: Take the person into the fresh air and keep him warm, let him rest; if there is difficulty in
breathing, medical advice is required.
In case of skin contact: In the event of contact with the skin, preferably wash with a
cleanser based on polyethylene glycol or with plenty of warm water and soap. Consult a
doctor in the event of a skin reaction.
In case of eye contact: Hold the eyes open and rinse with preferably lukewarm water for a
sufficiently long period of time (at least 10 minutes). Contact an
ophthalmologist. If swallowed: DO NOT induce the patient to vomit, medical advice is required.
Notes to physician: The product irritates the respiratory tract and may trigger sensitisation of
the skin and respiratory tract. Treatment of acute irritation or bronchial constriction is
primarily symptomatic. Extended medical treatment may be required depending on the
degree of exposure and the severity of the symptoms.
Date of issue/Date of revision : 26 /6 /2013 2/5
5. FIRE-FIGHTING MEASURES
Suitable extinguishing media: Carbon dioxide (CO2), Foam, extinguishing powder, in cases
of larger fires, water spray should be used.
Unsuitable extinguishing media: High volume water jet
Burning releases carbon monoxide, carbon dioxide, oxides of nitrogen, isocyanate vapors
and traces of hydrogen cyanide. In the event of fire and/or explosion do not breathe fumes.
Fire in vicinity poses risk of pressure build-up and rupture. Containers at risk from fire should
be cooled with water and, if possible, removed from the danger area.
During fire-fighting respirator with independent air-supply and airtight garment is required.
Do not allow contaminated extinguishing water to enter the soil, ground-water or surface waters.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions: Put on protective equipment (see chapter 8). Ensure adequate
ventilation/exhaust extraction. Keep unauthorized persons away.
Environmental precautions: Do not flush into surface water or sanitary sewer system.
Methods for cleaning up: Remove mechanically; cover the remainder with wet, absorbent
material (e.g. sawdust, chemical binder based on calcium silicate hydrate, sand).
After approx. one hour transfer to waste container and do not seal (evolution of
CO2!). Keep damp in a safe ventilated area for several days.
7. HANDLING AND STORAGE
Handling
Provide sufficient air exchange and/or exhaust in work rooms. Exhaust ventilation necessary
if product is sprayed.
Storage
Keep container tightly closed and dry. Further information on the storage conditions which
must be observed to preserve quality can be found in our product information sheet.
Date of issue/Date of revision : 26 /6 /2013 3/5
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Wear protective clothing, including eye protection and PVC or synthetic/rubber gloves. Wash hands and exposed skin before
meals and after work. Do not eat, drink or smoke whilst handling the product.
Respiratory protection:
Respiratory protection required in insufficiently ventilated working areas and during spraying.
An air-fed mask, or for short periods of work, a combination of charcoal filter and particulate
filter is recommended.
In case of hypersensitivity of the respiratory tract (e.g. asthmatics and those who suffer
from chronic bronchitis) it is inadvisable to work with the product
Hand protection:
Suitable materials for safety gloves; DIN EN 374-3:
Polychloroprene - CR: thickness >=0,5mm; breakthrough time >=480min.
Nitrile rubber - NBR: thickness >=0,35mm; breakthrough time >=480min.
Butyl rubber - IIR: thickness >=0,5mm; breakthrough time >=480min.
Fluorinated rubber - FKM: thickness >=0,4mm; breakthrough time >=480min.
Recommendation: contaminated gloves should be disposed of.
Eye protection:
Wear eye/face protection.
Skin and body protection:
Wear suitable protective clothing.
Hygiene measures:
Keep away from foodstuffs, drinks and tobacco. Wash hands before breaks and at the end of
workday. Keep working clothes separately. Take off all contaminated clothing immediately
Date of issue/Date of revision : 26 /6 /2013 4/5
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance Pale liquid Oxidising properties None
o
Odour Amine –like Vapour pressure < 8 hpa @ 25 C
o
pH > 7 (in water) Relative density 1.06 (25 C)
Boiling point Decomposes Bulk density Not relevant
Melting point Not Relevant Viscosity No data
o
Flash point >100 C (CC) Solubility Partially miscible with water
Autoignition temperature No data Partition coefficient No data
Explosive properties No data Other data Avoid contact with strong acids
and oxidizers.
10. STABILITY AND REACTIVITY
Chemical stability : The product is stable.
Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions
Conditions to avoid : No specific data.
Materials to avoid :
No known incompatibility
Date of issue/Date of revision : 26 /6 /2013 5/5
11. TOXICOLOGICAL INFORMATION
LD50 (rat, oral): > 5000mg/kg (by calculation). Eye irritation (rabbit): corrosive. Skin irritation (rabbit): corrosive.
Dermal sensitisation (guinea pig): sensitiser.
12. ECOLOGICAL INFORMATION
Ecotoxicological studies at the preparation are not available.
MOBILITY Likely to be mobile in soil.
DEGRADABILITY Readily biodegradable
ACCUMULATION There is little potential for bioaccumulation. Biomagnification is unlikely.
ECOTOXICITY Harmful to aquatic organisms:
13. DISPOSAL CONSIDERATIONS
Methods of disposal : The generation of waste should be avoided or minimized wherever possible. Empty
containers or liners may retain some product residues. This material and its container
must be disposed of in a safe way. Dispose of surplus and non-recyclable products via a
licensed waste disposal contractor. Disposal of this product, solutions a nd a n y b y - p r
o d u cts s h o u ld at a ll ti m es c o m p ly w ith the r e q u i r e m e nts o f environmental
protection and waste disposal legislation and any regional local authority requirements.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and
sewers.
14. TRANSPORT INFORMATION
International transport regulations
This material is not hazardous material for purpose of transportation under US department of Transportation table
of Hazardous materials,49 CFR 172.101
15. REGULATORY INFORMATION
Risk phrases : This product is not classified according to EU legislation.
Product use : Industrial applications.
16. OTHER INFORMATION
National Fire Protection :
Association (U.S.A.)
0 Flammability
0 0
Health Instability/Reactivity
Special
History
Version :1
Disclaimer
Information contained in this material safety data sheet is believed to be reliable and given in good faith,
but no representation, guarantee or warranties of any kind are made as to its accuracy, suitability for a
particular application or results to be obtained from them.
The user of this material decides what safety measures are necessary to safely use this material, either alone
or in combination with other materials.
FLORGARD EPU SL Part B
