MaxiSys Vehicle Diagnostic Report
Vehicle information
GM 2008 Chevrolet
VIN: Mileage:
Diagnostics time: 2023/05/17 18:14 Path: Control unit > V6 engine > Trouble codes > Read codes >
Additional DTC(s) >
Read codes
1. P0571:00 Brake switch circuit malfunction
Last test: Not ran
2. P0504:00 Brake switch circuit malfunction
Last test: Not ran
3. P0123:00 Throttle position sensor 1 circuit high voltage
Last test: Not ran
4. P0122:00 Throttle position sensor 1 circuit low voltage
Last test: Not ran
5. P0121:00 Throttle position sensor 1 circuit range/performance
Last test: Not ran
6. P0223:00 Throttle position sensor 2 circuit high voltage
Last test: Not ran
7. P0222:00 Throttle position sensor 2 circuit low voltage
Last test: Not ran
8. P0221:00 Throttle position sensor 2 circuit range/performance
Last test: Not ran
9. P2100:00 Throttle control motor malfunction
Last test: Not ran
10. P2101:00 Throttle control position range/performance
Last test: Not ran
11. P0638:00 Commanded versus actual throttle position correlation
Last test: Not ran
12. P013A:00 O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2
Last test: Not ran
13. P013E:00 O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2
Last test: Not ran
14. P013C:00 O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2
Last test: Not ran
15. P014A:00 O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2
Last test: Not ran
16. P1258:00 Engine coolant over temperature - protection mode active
Last test: Not ran
17. P0011:00 Intake camshaft position range/performance (bank 1)
Last test: Not ran
www.autel.com Page 1
MaxiSys Vehicle Diagnostic Report
18. P0021:00 Intake camshaft position range/performance (bank 2)
Last test: Not ran
19. P2177:00 Fuel trim lean during cruising/ acceleration (bank 1)
Last test: Not ran
20. P2178:00 Fuel trim rich during cruising/ acceleration (bank 1)
Last test: Not ran
21. P2179:00 Fuel trim lean during cruising/ acceleration (bank 2)
Last test: Not ran
22. P2180:00 Fuel trim rich during cruising/ acceleration (bank 2)
Last test: Not ran
23. P0101:00 Mass air flow sensor circuit range/performance
Last test: Not ran
24. P0141:00 O2 sensor heater circuit range/performance (bank 1 sensor 2)
Last test: Not ran
25. P0161:00 O2 sensor heater circuit range/performance (bank 2 sensor 2)
Last test: Not ran
26. P0038:00 O2 sensor heater circuit high voltage (bank 1 sensor 2)
Last test: Not ran
27. P0037:00 O2 sensor heater circuit low voltage (bank 1 sensor 2)
Last test: Not ran
28. P0036:00 O2 sensor heater circuit malfunction (bank 1 sensor 2)
Last test: Not ran
29. P0058:00 O2 sensor heater circuit high voltage (bank 2 sensor 2)
Last test: Not ran
30. P0057:00 O2 sensor heater circuit low voltage (bank 2 sensor 2)
Last test: Not ran
31. P0056:00 O2 sensor heater circuit malfunction (bank 2 sensor 2)
Last test: Not ran
32. P0135:00 O2 sensor heater circuit range/performance (bank 1 sensor 1)
Last test: Not ran
33. P0053:00 O2 sensor heater resistance range/performance (bank 1 sensor 1)
Last test: Not ran
34. P0155:00 O2 sensor heater circuit range/performance (bank 2 sensor 1)
Last test: Not ran
35. P0059:00 O2 sensor heater resistance range/performance (bank 2 sensor 1)
Last test: Not ran
36. P0420:00 Catalyst system low efficiency (bank 1)
Last test: Not ran
37. P0430:00 Catalyst system low efficiency (bank 2)
Last test: Not ran
38. P0324:00 Knock sensor module performance
www.autel.com Page 2
MaxiSys Vehicle Diagnostic Report
Last test: Not ran
39. P0328:00 Knock sensor circuit high frequency (bank 1)
Last test: Not ran
40. P0327:00 Knock sensor circuit low frequency (bank 1)
Last test: Not ran
41. P0326:00 Knock Sensor 1 Circuit Range/Performance Bank 1 or Single Sensor
Last test: Not ran
42. P0333:00 Knock sensor circuit high frequency (bank 2)
Last test: Not ran
43. P0332:00 Knock sensor circuit low frequency (bank 2)
Last test: Not ran
44. P0331:00 Knock Sensor 2 Circuit Range/Performance Bank 2
Last test: Not ran
45. P2270:00 O2 sensor lean/rich switch signal malfunction (bank 1 sensor 2)
Last test: Not ran
46. P2271:00 O2 sensor rich/lean switch signal malfunction (bank 1 sensor 2)
Last test: Not ran
47. P2272:00 O2 sensor lean/rich switch signal malfunction (bank 2 sensor 2)
Last test: Not ran
48. P2273:00 O2 sensor rich/lean switch signal malfunction (bank 2 sensor 2)
Last test: Not ran
49. P0133:00 O2 sensor circuit slow response (bank 1 sensor 1)
Last test: Not ran
50. P0153:00 O2 sensor circuit slow response (bank 2 sensor 1)
Last test: Not ran
51. P2097:00 Post catalyst O2 sensor fuel trim above upper limit (bank 1)
Last test: Not ran
52. P2096:00 Post catalyst O2 sensor fuel trim below lower limit (bank 1)
Last test: Not ran
53. P2099:00 Post catalyst O2 sensor fuel trim above upper limit (bank 2)
Last test: Not ran
54. P2098:00 Post catalyst O2 sensor fuel trim below lower limit (bank 2)
Last test: Not ran
55. P0138:00 O2 sensor circuit high voltage (bank 1 sensor 2)
Last test: Not ran
56. P0137:00 O2 sensor circuit low voltage (bank 1 sensor 2)
Last test: Not ran
57. P0140:00 O2 sensor circuit no activity detected (bank 1 sensor 2)
Last test: Not ran
58. P2232:00 O2 sensor signal short to heater circuit (bank 1 sensor 2)
Last test: Not ran
www.autel.com Page 3
MaxiSys Vehicle Diagnostic Report
59. P0158:00 O2 sensor circuit high voltage (bank 2 sensor 2)
Last test: Not ran
60. P0157:00 O2 sensor circuit low voltage (bank 2 sensor 2)
Last test: Not ran
61. P0160:00 O2 sensor circuit no activity detected (bank 2 sensor 2)
Last test: Not ran
62. P2235:00 O2 sensor signal short to heater circuit (bank 2 sensor 2)
Last test: Not ran
63. P0041:00 O2 sensor signals not plausible (bank 1 sensor 2 & bank 2 sensor 2)
Last test: Not ran
64. P0692:00 Cooling fan relay 1 circuit high voltage
Last test: Not ran
65. P0691:00 Cooling fan relay 1 circuit low voltage
Last test: Not ran
66. P0480:00 Cooling fan relay 1 circuit malfunction
Last test: Not ran
67. P0694:00 Cooling fan relay 2 and 3 circuit high voltage
Last test: Not ran
68. P0693:00 Cooling fan relay 2 and 3 circuit low voltage
Last test: Not ran
69. P0481:00 Cooling fan relay 2 and 3 circuit malfunction
Last test: Not ran
70. P1011:00 Intake camshaft actuator park position (bank 1)
Last test: Not ran
71. P1013:00 Intake camshaft actuator park position (bank 2)
Last test: Not ran
72. P2187:00 Fuel trim lean during idling/ deceleration (bank 1)
Last test: Not ran
73. P2188:00 Fuel trim rich during idling/ deceleration (bank 1)
Last test: Not ran
74. P2189:00 Fuel trim lean during idling/ deceleration (bank 2)
Last test: Not ran
75. P2190:00 Fuel trim rich during idling/ deceleration (bank 2)
Last test: Not ran
76. P0368:00 Exhaust camshaft position sensor high voltage (bank 1)
Last test: Not ran
77. P0367:00 Exhaust camshaft position sensor low voltage (bank 1)
Last test: Not ran
78. P0366:00 Exhaust camshaft position sensor range/performance (bank 1)
Last test: Not ran
79. P0393:00 Exhaust camshaft position sensor high voltage (bank 2)
www.autel.com Page 4
MaxiSys Vehicle Diagnostic Report
Last test: Not ran
80. P0392:00 Exhaust camshaft position sensor low voltage (bank 2)
Last test: Not ran
81. P0391:00 Exhaust camshaft position sensor range/performance (bank 2)
Last test: Not ran
82. P0850:00 Park/neutral signal circuit incorrect signal
Last test: Not ran
83. P0111:00 Intake Air Temperature Sensor 1 Circuit Range/Performance
Last test: Not ran
84. P0128:00 Engine coolant temperature below thermostat regulating temperature
Last test: Not ran
85. P0116:00 Engine coolant temperature sensor circuit range/performance
Last test: Not ran
86. P0501:00 Vehicle Speed Sensor A Range/Performance
Last test: Not ran
87. P0513:00 Wrong transponder key
Last test: Not ran
88. P1631:00 Immobiliser fuel enable incorrect signal
Last test: Not ran
89. P1648:00 Wrong security code entered
Last test: Not ran
90. P0338:00 Crankshaft position sensor circuit high duty cycle
Last test: Not ran
91. P0335:00 Crankshaft position sensor circuit malfunction
Last test: Not ran
92. P0336:00 Crankshaft position sensor signal range/performance
Last test: Not ran
93. P0575:00 Cruise Control Input Circuit
Last test: Not ran
94. P167D:00 Please refer to vehicle service manual.
Last test: Not ran
95. P2301:00 Ignition coil cylinder 1 circuit high voltage
Last test: Not ran
96. P2300:00 Ignition coil cylinder 1 circuit low voltage
Last test: Not ran
97. P0351:00 Ignition coil cylinder 1 circuit malfunction
Last test: Not ran
98. P2304:00 Ignition coil cylinder 2 circuit high voltage
Last test: Not ran
99. P2303:00 Ignition coil cylinder 2 circuit low voltage
Last test: Not ran
www.autel.com Page 5
MaxiSys Vehicle Diagnostic Report
100. P0352:00 Ignition coil cylinder 2 circuit malfunction
Last test: Not ran
101. P2307:00 Ignition coil cylinder 3 circuit high voltage
Last test: Not ran
102. P2306:00 Ignition coil cylinder 3 circuit low voltage
Last test: Not ran
103. P0353:00 Ignition coil cylinder 3 circuit malfunction
Last test: Not ran
104. P2310:00 Ignition coil cylinder 4 circuit high voltage
Last test: Not ran
105. P2309:00 Ignition coil cylinder 4 circuit low voltage
Last test: Not ran
106. P0354:00 Ignition coil cylinder 4 circuit malfunction
Last test: Not ran
107. P2313:00 Ignition coil cylinder 5 circuit low voltage
Last test: Not ran
108. P2312:00 Ignition coil cylinder 5 circuit low voltage
Last test: Not ran
109. P0355:00 Ignition coil cylinder 5 circuit malfunction
Last test: Not ran
110. P2316:00 Ignition coil cylinder 6 circuit high voltage
Last test: Not ran
111. P2315:00 Ignition coil cylinder 6 circuit low voltage
Last test: Not ran
112. P0356:00 Ignition coil cylinder 6 circuit malfunction
Last test: Not ran
113. P2089:00 Intake camshaft position control solenoid circuit high voltage (bank 1)
Last test: Not ran
114. P2088:00 Intake camshaft position control solenoid circuit low voltage (bank 1)
Last test: Not ran
115. P0010:00 Intake camshaft position control solenoid circuit malfunction (bank 1)
Last test: Not ran
116. P2093:00 Intake camshaft position control solenoid circuit high voltage (bank 2)
Last test: Not ran
117. P2092:00 Intake camshaft position control solenoid circuit low voltage (bank 2)
Last test: Not ran
118. P0020:00 Intake camshaft position control solenoid circuit malfunction (bank 2)
Last test: Not ran
119. P0262:00 Injector 1 control circuit high voltage
Last test: Not ran
120. P0261:00 Injector 1 control circuit low voltage
www.autel.com Page 6
MaxiSys Vehicle Diagnostic Report
Last test: Not ran
121. P0201:00 Injector 1 control circuit malfunction
Last test: Not ran
122. P0265:00 Injector 2 control circuit high voltage
Last test: Not ran
123. P0264:00 Injector 2 control circuit low voltage
Last test: Not ran
124. P0202:00 Injector 2 control circuit malfunction
Last test: Not ran
125. P0268:00 Injector 3 control circuit high voltage
Last test: Not ran
126. P0267:00 Injector 3 control circuit low voltage
Last test: Not ran
127. P0203:00 Injector 3 control circuit malfunction
Last test: Not ran
128. P0271:00 Injector 4 control circuit high voltage
Last test: Not ran
129. P0270:00 Injector 4 control circuit low voltage
Last test: Not ran
130. P0204:00 Injector 4 control circuit malfunction
Last test: Not ran
131. P0274:00 Injector 5 control circuit high voltage
Last test: Not ran
132. P0273:00 Injector 5 control circuit low voltage
Last test: Not ran
133. P0205:00 Injector 5 control circuit malfunction
Last test: Not ran
134. P0277:00 Injector 6 control circuit high voltage
Last test: Not ran
135. P0276:00 Injector 6 control circuit low voltage
Last test: Not ran
136. P0206:00 Injector 6 control circuit malfunction
Last test: Not ran
137. P2123:00 Accelerator pedal position sensor 1 voltage high
Last test: Not ran
138. P2122:00 Accelerator pedal position sensor 1 voltage low
Last test: Not ran
139. P2138:00 Accelerator pedal position sensor 1-2 correlation
Last test: Not ran
140. P2128:00 Accelerator pedal position sensor 2 voltage high
Last test: Not ran
www.autel.com Page 7
MaxiSys Vehicle Diagnostic Report
141. P2127:00 Accelerator pedal position sensor 2 voltage low
Last test: Not ran
142. P0463:00 Fuel level sensor high voltage
Last test: Not ran
143. P0462:00 Fuel level sensor low voltage
Last test: Not ran
144. P2066:00 Fuel level sensor 2 range/performance
Last test: Not ran
145. P0461:00 Fuel level sensor range/performance
Last test: Not ran
146. P2068:00 Fuel level sensor 2 high voltage
Last test: Not ran
147. P2067:00 Fuel level sensor 2 low voltage
Last test: Not ran
148. P2636:00 Fuel pump insufficient flow detected
Last test: Not ran
149. P0103:00 Mass air flow sensor voltage high
Last test: Not ran
150. P0102:00 Mass air flow sensor voltage low
Last test: Not ran
151. P0100:00 Mass or Volume Air Flow A Circuit
Last test: Not ran
152. P0687:00 Engine control ignition relay circuit high voltage
Last test: Not ran
153. P0686:00 Engine control ignition relay circuit low voltage
Last test: Not ran
154. P0685:00 Engine control ignition relay circuit malfunction
Last test: Not ran
155. P0032:00 O2 sensor heater circuit high voltage (bank 1 sensor 1)
Last test: Not ran
156. P0031:00 O2 sensor heater circuit low voltage (bank 1 sensor 1)
Last test: Not ran
157. P0030:00 O2 sensor heater circuit malfunction (bank 1 sensor 1)
Last test: Not ran
158. P0052:00 O2 sensor heater circuit high voltage (bank 2 sensor 1)
Last test: Not ran
159. P0051:00 O2 sensor heater circuit low voltage (bank 2 sensor 1)
Last test: Not ran
160. P0050:00 O2 sensor heater circuit malfunction (bank 2 sensor 1)
Last test: Not ran
161. P0629:00 Fuel pump relay voltage high
www.autel.com Page 8
MaxiSys Vehicle Diagnostic Report
Last test: Not ran
162. P0628:00 Fuel pump relay voltage low
Last test: Not ran
163. P0627:00 Fuel pump relay circuit malfunction
Last test: Not ran
164. P0507:00 Idle speed control RPM too low
Last test: Not ran
165. P0506:00 Idle speed control RPM too low
Last test: Not ran
166. P0132:00 O2 sensor circuit high voltage (bank 1 sensor 1)
Last test: Not ran
167. P0131:00 O2 sensor circuit low voltage (bank 1 sensor 1)
Last test: Not ran
www.autel.com Page 9
