Machine Translated by Google

1 2 3 4 5 6 7 8

Hook customers take care of themselves Well plan SpecificationTechnical specification

Well elevation Pÿ15KN Schematic diagram of the hall door on the top floor

The outer width of the frame is 1530 Type Of Lift Elevator Type Wire Rope Villa Ladder A

Model Of Lift S1000

Well width 1430 Elevator model

Car gauge 1220 Rated Load(kg) load 480kg

Host installation surface

056
056
Rated Speed(m/s) speed 0.3m/s
Counterweight rail distance 950

Roping Traction ratio 2:1

0024

051
Type Of Control control type VVVF
003

150 Floor/ Stop/Door 3

floor/station/door landing door 3 3
0022

0051
Door Open Type Open the door on the left side to open the automatic door
45
top_height
Car net width 1100
800 x 2100

097
Door Dimension

0022
B

0012
046
350
B Car Dimension Car net size 1100 x 1150 2300
x
Door
door door

0521
Min Floor Spacing minimum floor distance OPH+500
100

Motor Power(kw) motor power

2.7

05
eW
n
d
1
eC
n
d
1

pet7
prta1
urF
o
d
1

h0tll3
h0t5
eat8
pis3
eedm
0 e
Rated Current(A) rated current 13

066
300 150 Supply For Power Power supply A.C 3-380V 50HZ

097
door width 800
Control cabinet hole
decorative level

07
A.C 2-220V 50HZ

08
Supply For Light lighting power supply

03
R1 35
Force Into Building
R2 30
C

001
Door opening width 800, Pit Force (KN)
R3/R4 12
C
Schematic diagram of hall doors on other floors
365 door opening width 1000 65

Special Instructions:

1. At present, there are no relevant laws and regulations for villa home elevators that require compulsory acceptance

, so villa elevators do not need to apply for inspection. This design scheme refers to the provisions

003
of "GB/T 21739- and implements the 2008 Household Elevator Manufacturing and Installation Specifications"

related design specifications.

2. Special reminder: villa elevators are only for installation in private residences, for a single

Buffer/Hook Diagram family members use. or installed in buildings for non-single-family use,
45
As a vehicle for a single family to enter their residence, but the public within the building
0051

0022

0012
lift
Or other occupants cannot enter and use.
0066

Press /

3. The user installs the main switch of power (three-phase five-wire) and lighting main power on the

051
D
door door On the wall where the power box is 1.3 meters above the ground at the designated place on the top floor. The power supply of the elevator should be

D Separately controlled and identified by marks. The supply voltage fluctuation should be within the rated voltage ±7

0521
% range.

height 4. The four walls of the hoistway (including the ring beams of each layer) should be vertical, and the horizontal dimension of the hoistway (
049

05
hook The allowable deviation value of the minimum headroom size measured with a plumb line is: 0ÿÿ20

mm.

003
5. A permanent electrical lighting device should be installed in the shaft, and the distance from the highest to the lowest is 0.3m

One for each, reasonably arranged in the middle to ensure that the brightness of the shaft is not less than 50LX
800
door width decorative level
6. The bottom of the hoistway should be equipped with a pit, except for the buffer seat, guide rail seat and drainage

Outside the device, the bottom of the pit should be smooth and flat, and the pit should not be used as a water pit

eWn
d
1

urF
o
d
1
pet7

eat8
e
use. After installation of guide rails, buffers, fences, etc.

h0tll3

pis3
eedm
0
003

After construction, the pit shall not seep or leak.

003

7. After the traction machine is installed, the vertical error of the car and the counterweight guide rail in the X/Y direction
097

AND

The difference is ÿ1mm, and the installation gap between the car and the counterweight guide shoe and guide rail is ÿ3mm.
0022

AND 8. After the steel belt is hung, all the forces should be adjusted to be consistent, and it should pass the inspection of moving and slow cars

buffer Whether there is deviation of the steel belt. If there is deviation, check the concentric straightness of the three,

Two-axis horizontality of the host.

top floor 4200
0051

6F
Door
715 715
5F SAFE ELEVATOR
Well clear width 1430
4F
project name:
The outer width of the frame is 1530
3F The presidential
residence Project
0021

008

2f

Drawing Numbers WJS230805001 Version A

1F F
Pit
design Date 2023/8/5
F
-1F 3300
review Date
-2F 3300
Customer confirmation (stamp)

Note: 1. This figure is not to scale, please do not measure, the unit is mm; 2. The control cabinet must be within 2m of the hoistway, and the excess cable must be lengthened. pit 1200

Floor height(mm) signature: date:

1 2 3 4 5 6 7 8