0% found this document useful (0 votes)

375 views123 pages

2009 Harley Davidson Fat Bob 28

Uploaded by

Bob McRaw

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

375 views123 pages

2009 Harley Davidson Fat Bob 28

Uploaded by

Bob McRaw

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 123

2009

Fat Bob Owner's Manual

Safety First

Safe Operating Rules: Dyna Models

Motorcycles are different from other vehicles. They
operate, steer, handle and brake differently. Unskilled or
improper use could result in loss of control, death or
serious injury. (00556c)

Take a rider training course.
Read Owner's Manual before riding, adding accessories or servicing.
Wear a helmet, eye protection and protective clothing.
Never tow a trailer.

Before operating your new motorcycle it is your responsibility to read and follow the operating and
maintenance instructions in this manual, and follow these basic rules for your personal safety.

Know and respect the rules of the road (see RULES OF THE ROAD section). Carefully read
and observe the rules contained in the RIDING TIPS booklet accompanying this Owner's
Manual. Read and familiarize yourself with the contents of the MOTORCYCLE HANDBOOK
for your state.
Before starting engine, check for proper operation of brake, clutch, shifter, throttle controls,
correct fuel and oil supply.

Do not use aftermarket parts and custom made front forks
which can adversely affect performance and handling.
Removing or altering factory installed parts can adversely
affect performance and could result in death or serious
injury. (00001a)

Use only HarleyDavidson approved parts and accessories. Use of certain other
manufacturer's performance parts will void your new motorcycle warranty. See your Harley
Davidson dealer for details.

Stop the engine when refueling or servicing the fuel
system. Do not smoke or allow open flame or sparks near
gasoline. Gasoline is extremely flammable and highly
explosive, which could result in death or serious injury.
(00002a)

When refueling your motorcycle, the following rules should be observed.
Refuel in a well ventilated area with the engine turned off.
Remove fuel filler cap slowly.
Do not smoke or allow open flames or sparks when refueling or servicing the fuel system.
Do not fill fuel tank above the bottom of the filler neck insert.
Leave air space to allow for fuel expansion.

Do not store motorcycle with gasoline in tank within the
home or garage where open flames, pilot lights, sparks or
electric motors are present. Gasoline is extremely
flammable and highly explosive, which could result in
death or serious injury. (00003a)

Engine exhaust from this product contains chemicals
known to the State of California to cause cancer, and birth
defects or other reproductive harm. (00004f)

Wheel weights on wheels without spokes contain lead and
lead compounds, chemicals known to the State of
California to cause cancer, and birth defects or other
reproductive harm. (00356d)

Do not run motorcycle in a closed garage or confined area.
Inhaling motorcycle exhaust, which contains poisonous
carbon monoxide gas, could result in death or serious
injury. (00005a)

The jiffy stand locks when placed in the full forward (down)
position with vehicle weight on it. If the jiffy stand is not in
the full forward (down) position with vehicle weight on it,
the vehicle can fall over which could result in death or
serious injury. (00006a)

Be sure jiffy stand is fully retracted before riding. If jiffy
stand is not fully retracted, it can contact the road surface
causing a loss of vehicle control, which could result in
death or serious injury. (00007a)

A new motorcycle must be operated according to the special breakin procedure. See
Breakin Riding Rules.
Operate motorcycle only at moderate speed and out of traffic until you have become
thoroughly familiar with its operation and handling characteristics under all conditions.
NOTE:

We recommend that you obtain information and formal training in the correct motorcycle riding
technique. In the United States, the Motorcycle Safety Foundation® offers beginning and
advanced rider safety courses. Call (949)7273227 for information.

Do not exceed the legal speed limit or drive too fast for existing conditions. Always reduce
speed when poor driving conditions exist. High speed increases the influence of any other
condition affecting stability and increases the possibility of loss of control.
Pay strict attention to road surfaces and wind conditions. Any two wheeled vehicle may be
subject to upsetting forces such as wind blasts from passing trucks, holes in the pavement,
rough road surfaces, rider control error, etc. These forces may influence the handling
characteristics of your motorcycle. If this happens, reduce speed and guide the motorcycle
with a relaxed grip to a controlled condition. Do not brake abruptly or force the handlebar.
This may aggravate an unstable condition.
Keep cargo weight concentrated close to the motorcycle and as low as possible to minimize
the change in the motorcycle's center of gravity. Distribute weight evenly on both sides of
the vehicle and do not load bulky items too far behind the rider or add weight to the
handlebars or front forks. Do not exceed maximum specified load in each saddlebag.
NOTE:

New riders should gain experience under various conditions while driving at moderate speeds.

Operate your motorcycle defensively. Remember, a motorcycle does not afford the same
protection as an automobile in an accident. One of the most common accident situations
occurs when the driver of the other vehicle fails to see or recognize a motorcycle and turns
left into the oncoming motorcyclist. Operate only with headlamp on.
Wear an approved helmet, clothing, and foot gear suited for motorcycle riding. Bright or light
colors are best for greater visibility in traffic, especially at night. Avoid loose, flowing
garments and scarves.

Avoid contact with exhaust system and wear protective
clothing that completely covers legs while riding. Exhaust
pipes and mufflers get very hot when engine is running
and remain too hot to touch, even after engine is turned
off. Failure to wear protective clothing could result in
burns or other serious injury. (00009a)

When carrying passengers, it is your responsibility to instruct them on proper riding
procedures. (See Riding Tips for Motorcyclist included in your HarleyDavidson Owner's Kit.)
Do not allow other individuals, under any circumstances, to operate your motorcycle unless
you know they are experienced, licensed riders and are thoroughly familiar with the
operation of your particular motorcycle.

Protect your motorcycle against theft. After parking your motorcycle, lock the steering head
and remove ignition key from switch. Set security alarm if present.
Safe motorcycle operation requires alert mental judgment combined with a defensive driving
attitude. Do not allow fatigue, alcohol or drugs to endanger your safety or that of others.
Vehicles equipped with a sound system should have the volume adjusted to a nondistracting
level before operating vehicle.
Maintain your motorcycle in proper operating condition in accordance with Regular Service
Intervals: 2009 Dyna Models. Particularly important to motorcycle stability is proper tire
inflation pressure, tread condition, and proper adjustment of wheel bearings and steering
head bearings.

Do not operate vehicle with forks locked. Locking the forks
restricts the vehicle's turning ability, which could result in
death or serious injury. (00035a)

Perform the service and maintenance operations as
indicated in the regular service interval table. Lack of
regular maintenance at the recommended intervals can
affect the safe operation of your motorcycle, which could
result in death or serious injury. (00010a)

Do not operate motorcycle with loose, worn or damaged
steering or suspension systems. Contact a Harley
Davidson dealer for repairs. Loose, worn or damaged
steering or suspension components can adversely affect
stability and handling, which could result in death or
serious injury. (00011a)

Regularly inspect shock absorbers and front forks.
Replace leaking, damaged or worn parts that can
adversely affect stability and handling, which could result
in death or serious injury. (00012a)

Use HarleyDavidson replacement fasteners. Aftermarket
fasteners can adversely affect performance, which could
result in death or serious injury. (00013a)
See your HarleyDavidson service manual for proper torque values.
Aftermarket fasteners may not have the specific property requirements to perform properly.

Replace punctured or damaged tires. In some cases, small
punctures in the tread area may be repaired from within
the demounted tire by a HarleyDavidson dealer. Speed
should NOT exceed 50 mph (80 km/h) for the first 24 hours
after repair, and the repaired tire should NEVER be used
over 80 mph (130 km/h). Failure to follow this warning
could result in death or serious injury. (00015a)

Do not exceed the motorcycle's Gross Vehicle Weight
Rating (GVWR) or Gross Axle Weight Rating (GAWR).
Exceeding these weight ratings can affect stability and
handling, which could result in death or serious injury.
(00016e)

GVWR is the sum of the weight of the motorcycle, accessories, and the maximum weight of
the rider, passenger and cargo that can be safely carried.
The GVWR is shown on the information plate, located on the frame steering head.
GAWR is the maximum amount of weight that can be safely carried on each axle. Refer to
Weights: 2009 Dyna Models.

Do not tow a disabled motorcycle. Towing can adversely
affect stability and handling, which could result in death or
serious injury. (00017a)

Do not pull a trailer with a motorcycle. Pulling a trailer can
cause tire overload, reduced braking efficiency and
adversely affect stability and handling, which could result
in death or serious injury. (00018b)
Direct contact of D.O.T. 4 brake fluid with eyes can cause
irritation. Avoid eye contact. In case of eye contact flush
with large amounts of water and get medical attention.
Swallowing large amounts of D.O.T. 4 brake fluid can
cause digestive discomfort. If swallowed, obtain medical
attention. Use in well ventilated area. KEEP OUT OF
REACH OF CHILDREN. (00240a)

Consult a HarleyDavidson dealer regarding any questions
or problems that occur in the operation of your
motorcycle. Failure to do so can aggravate an initial
problem, cause costly repairs, cause an accident and
could result in death or serious injury. (00020a)

Be sure all equipment required by federal, state and local law is installed and in good
operating condition.

Rules of the Road

Always sound your horn, actuate your turn signals, and exercise caution when passing other
vehicles going in the same direction. Never try to pass another vehicle going in the same
direction at street intersections, on curves, or when going up or down a hill.
At street intersections give the rightofway. Do not presume you have the rightofway, as
the other driver may not know it is your turn.
Always signal when preparing to stop, turn or pass.
All traffic signs, including those used for the control of traffic at intersections, should be
obeyed promptly. SLOW DOWN signs near schools and CAUTION signs at railroad
crossings should always be observed and your actions governed accordingly.
When intending to turn, signal at least 100 feet 30.5 meters before reaching the turning
point. If turning across an intersection, move over to the centerline of the street (unless local
rules require otherwise). Slow down when entering the intersection and turn carefully.
Never anticipate a traffic light. When a change is indicated from GO to STOP (or vice versa)
in the traffic control systems at intersections, slow down and wait for the light to change.
Never run through a yellow or red traffic light.
While turning either right or left, watch for pedestrians, animals, as well as vehicles.
Do not leave the curb or parking area without signaling. Be sure your way is clear to enter
moving traffic. A moving line of traffic always has the rightofway.
Be sure your license plate is installed in the position specified by law and is clearly visible at
all times. Keep the plate clean.
Ride at a safe speed that is consistent with the type of highway you are on. Pay strict
attention to whether the road is dry, oily, icy or wet.
Watch for debris such as leaves or loose gravel.
Weather and traffic conditions on the highway dictate adjusting your speed and driving
habits accordingly.

Accessories and Cargo

HarleyDavidson Motor Company cannot test and make specific recommendations concerning
every accessory or combination of accessories sold. Therefore, the rider must be responsible for
safe operation of the motorcycle when installing accessories or carrying additional weight.

See the Accessory and Cargo section in your Owner's
Manual. Improper loading of cargo or installation of
accessories can affect motorcycle stability and handling,
which could result in death or serious injury. (00021a)

GVWR is the sum of the weight of the motorcycle, accessories, and the maximum weight of
the rider, passenger and cargo that can be safely carried.
GAWR is the maximum amount of weight that can be safely carried on each axle.
The GVWR and GAWR are shown on the information plate which is located on the frame
down tube.

Accessory and Cargo Guidelines

The following guidelines should be used when equipping a motorcycle, carrying passengers
and/or cargo.

Travel at speeds appropriate for road and conditions and
never travel faster than posted speed limit. Excessive
speed can cause loss of vehicle control, which could
result in death or serious injury. (00008a)
Do not exceed the legal speed limit or drive too fast for existing conditions. Always reduce
speed when poor driving conditions exist. High speed increases the influence of any other
condition affecting stability and increases the possibility of loss of control.
Pay strict attention to road surfaces and wind conditions. Any two wheeled vehicle may be
subject to upsetting forces such as wind blasts from passing trucks, holes in the pavement,
rough road surfaces, rider control error, etc. These forces may influence the handling
characteristics of your motorcycle. If this happens, reduce speed and guide the motorcycle
with a relaxed grip to a controlled condition. Do not brake abruptly or force the handlebar.
This may aggravate an unstable condition.
Keep cargo weight concentrated close to the motorcycle and as low as possible. This
minimizes the change in the motorcycle's center of gravity.
Distribute weight evenly on both sides of the vehicle.
Do not load bulky items too far behind the rider or add weight to the handlebars or front
forks.
Do not exceed maximum specified load in each saddlebag.
Luggage racks are designed for lightweight items. Do not overload racks.
Be sure cargo is secure and will not shift while riding and recheck the cargo periodically.
Accessories that change the operator's riding position may increase reaction time and affect
handling of the motorcycle.
Additional electrical equipment may overload the motorcycle's electrical system possibly
resulting in electrical system and/or component failure.

The front and/or rear guard(s) can provide limited leg and
cosmetic vehicle protection under unique circumstances.
(Fall over while stopped, very slow speed slide.) It is not
made or intended to provide protection from bodily injury
in a collision with another vehicle or any other object.
(00022a)

Large surfaces such as fairings, windshields, back rests, and luggage racks can adversely affect
handling. Only genuine HarleyDavidson items designed specifically for the motorcycle model
should be used with proper installation.

Only Touring HarleyDavidson Motorcycles are suitable for
sidecar use. Consult a HarleyDavidson dealer. Use of
motorcycles other than Touring models with sidecars
could result in death or serious injury. (00040a)

Noise Control System
Tampering

Owners are warned that removal or replacement of any noise control system component may be
prohibited by law. This prohibition applies prior to vehicle sale or delivery to the ultimate
purchaser. Use of a vehicle on which noise control system components have been removed or
rendered inoperative may also be prohibited by law.

Identification

Vehicle Identification Number

See V.I.N. Stamping Location. The full 17 digit serial or Vehicle Identification Number (V.I.N.)
is stamped on the steering head and on a label located on the right front frame down tube.

An abbreviated V.I.N. is stamped on the left side crankcase at the base of the rear cylinder.
NOTE:

Always give the full 17 digit Vehicle Identification Number when ordering parts or making any
inquiry about your motorcycle.

V.I.N. Stamping Location
Typical HarleyDavidson V.I.N.: 2009 Dyna Models

HarleyDavidson V.I.N. Breakdown: 2009 Dyna Models

POSITION DESCRIPTION POSSIBLE VALUES

1 Market designation 1=Originally manufactured for sale within the United States

5=Originally manufactured for sale outside of the United States
2 Manufacturer HD=HarleyDavidson
3 Motorcycle type 1=Heavyweight motorcycle (901 cc and larger)
4 Model See V.I.N. model table
5 Engine type 4=Twin Cam 96™, 1584 cc aircooled, fuelinjected
6 Introduction date 1=Regular

2=Midyear

3=California/regular

4=Cosmetic changes and/or special introductory date

5=California/cosmetic changes and/or special introductory date

6=California/midyear
7 V.I.N. check digit Can be 09 or X
8 Model year 9=2009
9 Assembly plant K=Kansas City, MO U.S.A.
10 Sequential number varies

V.I.N. Model Codes: 2009 Dyna Models

CODE MODEL CODE MODEL

GM FXD Dyna Super Glide® GX FXDB Street Bob™
GV FXDC Dyna Super Glide Custom® GY FXDF Fat Bob™
GN FXDL Dyna Low Rider®

Labels

See Labels: Dyna Models for safety and maintenance labels which were on the vehicle when
new. If removed, replacement labels may be purchased for your motorcycle. Refer to Labels:
Dyna Models for label descriptions.
NOTE:

Some labels may be available in different languages for destinations outside the U.S. See a
HarleyDavidson dealer for all labels available for purchase.

Labels: Dyna Models

LABEL PART NO. DESCRIPTION LOCATION

1 1536801A Battery warning Top of battery tray cover.
2 2910808 General warnings Top of air cleaner cover.
3 1356906 Fuse block label Inside left side cover.

Labels: Dyna Models

Specifications

Specifications: 2009 Dyna Models

Engine: 2009 Dyna Models

ITEM SPECIFICATION
Number of 2
cylinders
Type 4cycle, 45 degree

VType, air cooled
Compression 9.21
ratio
Bore 3.750 in. 95.25 mm
Stroke 4.380 in. 111.25 mm
Displacement 96.00 cu. in. 1584.00 cu. cm
Torque 92.00 ftlbs @ 3000 124.75 Nm @ 3000
RPM RPM

Ignition System: 2009 Twin Cam Models

COMPONENT SPECIFICATION
Ignition timing Not adjustable
Battery 12 volt, 19 amp/hr,

sealed and maintenance free
Spark plug type HD6R12
Spark plug size 12 mm
Spark plug gap 0.0380.043 in. 0.971.09 mm
Spark plug torque 1218 ftlbs 16.324.4 Nm

Transmission: 2009 Dyna Models

TRANSMISSION SPECIFICATION
Type Constant mesh, foot shift
Speeds 6 forward

NOTE:

Specifications in this publication may not match those of official certification in some markets due
to timing of publication printing, variance in testing methods, and/or vehicle differences.
Customers seeking officially recognized regulatory specifications for their vehicle should refer to
certification documents and/or contact their respective dealer or distributor.

Sprocket Teeth: 2009 Dyna Models

DRIVE ITEM NUMBER OF TEETH

Primary Engine 34
Clutch 46
Final Transmission 32
Rear wheel 66*
*64 teeth on Japanese models
Gear Ratios: 2009 Dyna Models

GEAR RATIO
DOMESTIC AND JAPANESE
INTERNATIONAL MODELS
1st 9.312 9.030
Gear
2nd 6.421 6.266
Gear
3rd 4.774 4.630
Gear
4th 3.926 3.807
Gear
5th 3.279 3.179
Gear
6th 2.790 2.706
Gear

NOTE:

Gross Vehicle Weight Rating (GVWR) (maximum allowable loaded vehicle weight) and
corresponding Gross Axle Weight Ratings (GAWR) are given on a label located on the frame
below the steering head.

Weights: 2009 Dyna Models

ITEM FXD FXDC FXDL FXDB FXDF

LB. KG LB. KG LB. KG LB. KG LB. KG
Weight (as 632.00 286.67 645.00 292.57 641.00 290.75 634.00 287.58 669.70 303.77
shipped
from
factory)
GVWR 1085.00 492.15 1085.00 492.15 1085.00 492.15 1085.00 492.15 1085.00 492.15
GAWR front 390.00 176.90 390.00 176.90 390.00 176.90 390.00 176.90 390.00 176.90
GAWR rear 695.00 315.25 695.00 315.25 695.00 315.25 695.00 315.25 695.00 315.25

Dimensions: 2009 Dyna Models

ITEM FXD FXDC FXDL FXDB FXDF

IN. MM IN. MM IN. MM IN. MM IN. MM
Wheel base 64.20 1630.68 64.20 1630.68 64.60 1640.89 64.20 1630.68 63.77 1619.76
Overall length 92.80 2357.12 92.90 2359.66 93.10 2364.74 92.80 2357.12 91.73 2329.94
Overall width 36.70 932.18 38.90 988.06 36.30 922.02 37.50 952.50 35.03 889.76
Road clearance 5.32 135.13 5.32 135.13 4.92 124.97 4.92 124.97 4.92 124.99
Overall height 46.80 1188.72 47.70 1211.58 47.00 1193.80 50.40 1280.16 44.56 1131.82
Saddle height* 26.60 675.64 26.80 680.72 25.80 655.32 25.56 649.22 26.10 662.94
*With 180 lb. 81.6 kg rider on seat.

Capacities: 2009 Dyna Models

ITEM FXD FXDC FXDL FXDB FXDF

U.S. LITERS U.S. LITERS U.S. LITERS U.S. LITERS U.S. LITERS
Fuel tank (total) 4.80 18.17 5.00 18.93 4.80 18.17 4.80 18.17 5.00 18.93
gal gal gal gal gal
Oil tank with filter 3.00 2.84 3.00 2.84 3.00 2.84 3.00 2.84 3.00 2.84
qt. qt. qt. qt. qt.
Transmission 1.00 0.95 1.00 0.95 1.00 0.95 1.00 0.95 1.00 0.95
qt. qt. qt. qt. qt.
(approximate)
Primary chaincase 1.00 0.95 1.00 0.95 1.00 0.95 1.00 0.95 1.00 0.95
qt. qt. qt. qt. qt.
(approximate)
Low fuel warning 0.90 3.41 0.90 3.41 0.90 3.41 0.90 3.41 0.90 3.41
light on gal gal gal gal gal

Tire Pressures: 2009 Dyna Models

MODEL LOAD TIRE PRESSURE (COLD)

FRONT REAR
PSI kPa PSI kPa
All models except FXDF Solo rider 30 206 36 248
Rider and passenger 30 206 40 275
FXDF Solo rider 36 248 36 248
Rider and passenger 36 248 40 275

Tire Sizes: 2009 Dyna Models

MODEL MOUNT SIZE NUMBER

All models except FXDF Front 19 in. D401F 100/9019
Rear 17 in. K591 160/70B17
FXDF Front 16 in. D427F 130/90B16
Rear 16 in. D427 180/70B16
2009 motorcycles use Dunlop HarleyDavidson tires only.

Bulb Chart: 2009 Dyna Models

LAMP DESCRIPTION BULBS CURRENT HD

REQUIRED DRAW PART
NUMBER
(AMPERAGE)
Headlamp High beam/low beam (FXDF, 2 5.0/4.58 6983808
domestic)
High beam/low beam (FXDF, 2 5.0/4.58 6888101
international)
High beam/low beam (all other 1 5.0/4.58 6832903
models)
Position lamp (FXDF, 1 0.32 5343697
international)
Position lamp (other models, 1 0.32 5343892
international)
Tail and stop lamp Tail/stop lamp (FXDB) Illuminated with LEDs. Replace entire
assembly upon failure.
Tail/stop lamp (other models, 1 0.59/2.10 6802699
domestic)
Tail/stop lamp (other models, 1 0.59/2.10 6816704
international)
Turn signal lamp Front/running 2 2.25/0.59 6816889A
Front international 2 1.75 6816384
Rear (FXDB, domestic) 2 2.25 6816889A
Rear (other models, domestic) 2 2.25 6857264B
Rear international 2 1.75 6816384
Instrument panel High beam indicator Illuminated with LEDs. Replace entire
indicators Oil pressure indicator assembly upon failure.
Neutral indicator
Turn signal indicators
Fuel Gauge All models use an LED built into the gauge.

Tire Data

Match tires, tubes, air valves and caps to the correct wheel
rim. Contact a HarleyDavidson dealer. Mismatching can
result in damage to the tire bead, allow tire slippage on the
rim or cause tire failure, which could result in death or
serious injury. (00023a)

Use only HarleyDavidson approved tires. See a Harley
Davidson dealer. Using nonapproved tires can adversely
affect stability, which could result in death or serious
injury. (00024a)

Tubeless tires fitted with the correct size inner tubes may be used on all HarleyDavidson laced
(wire spoked) wheels. Protective rubber rim strips must be used with tubeless tires (fitted with
correct size inner tubes) when mounted on laced (wire spoked) wheels.

Use inner tubes on laced (wire spoked) wheels. Using
tubeless tires on laced wheels can cause air leaks, which
could result in death or serious injury. (00025a)

Tubeless tires are used on all HarleyDavidson cast and disc wheels.

Tire sizes are molded on the tire sidewall. Inner tube sizes are printed on the tube.

HarleyDavidson front and rear tires are not the same.
Interchanging front and rear tires can cause tire failure,
which could result in death or serious injury. (00026a)

Do not inflate tire beyond maximum pressure as specified
on sidewall. Over inflated tires can blow out, which could
result in death or serious injury. (00027a)

HarleyDavidson tires are equipped with wear bars that run
horizontally across the tread. When wear bars become
visible and only 1/32 in. (0.8 mm) tread depth remains,
replace tire immediately. Using a worn tire can adversely
affect stability and handling, which could result in death or
serious injury. Use only HarleyDavidson approved
replacement tires. (00090b)

See Specifications: 2009 Dyna Models for tire pressures and sizes.

Gasoline Blends

Your motorcycle was designed to get the best performance and efficiency using unleaded
gasoline. Most gasoline is blended with alcohol and/or ether to create oxygenated blends. The
type and amount of alcohol or ether added to the fuel is important.

Do not use gasoline that contains methanol. Doing so can
result in fuel system component failure, engine damage
and/or equipment malfunction. (00148a)

Gasoline containing METHYL TERTIARY BUTYL ETHER (MTBE): Gasoline/MTBE blends
are a mixture of gasoline and as much as 15% MTBE. Gasoline/MTBE blends can be used
in your motorcycle.
ETHANOL is a mixture of 10% ethanol (Grain alcohol) and 90% unleaded gasoline.
Gasoline/ethanol blends can be used in your motorcycle if the ethanol content does not
exceed 10%.
REFORMULATED OR OXYGENATED GASOLINES (RFG): Reformulated gasoline is a
term used to describe gasoline blends that are specifically designed to burn cleaner than
other types of gasoline, leaving fewer tailpipe emissions. They are also formulated to
evaporate less when you are filling your tank. Reformulated gasolines use additives to
oxygenate the gas. Your motorcycle will run normally using this type of gas and Harley
Davidson recommends you use it when possible, as an aid to cleaner air in our
environment.
Do not use race gas or octane boosters. Use of these fuels will damage the fuel system.

Some gasoline blends might adversely affect the starting, driveability or fuel efficiency of the
motorcycle. If any of these problems are experienced, try a different brand of gasoline or gasoline
with a higher octane blend.

Fuel

Refer to Octane Ratings. Always use a good quality unleaded gasoline. Octane ratings are
usually found on the pump.

Avoid spills. Slowly remove filler cap. Do not fill above
bottom of filler neck insert, leaving air space for fuel
expansion. Secure filler cap after refueling. Gasoline is
extremely flammable and highly explosive, which could
result in death or serious injury. (00028a)

Use care when refueling. Pressurized air in fuel tank can
force gasoline to escape through filler tube. Gasoline is
extremely flammable and highly explosive, which could
result in death or serious injury. (00029a)

Modern service station pumps dispense a high flow of gasoline into a motorcycle fuel tank making
air entrapment and pressurization a possibility.

Octane Ratings

SPECIFICATION RATING
Pump Octane (R+M)/2 91 (95 RON)

Catalytic Converters: Dyna Models
All FXDF models are equipped with catalytic converters.

For all other Dyna models, only international, Japan, and California markets include catalytic
converters.

Do not operate catalytic converterequipped vehicle with
engine misfire or a nonfiring cylinder. If you operate the
vehicle under these conditions, the exhaust will become
abnormally hot, which can cause vehicle damage,
including emission control loss. (00149a)

Use only unleaded fuel in catalytic converterequipped
motorcycles. Using leaded fuel will damage the emission
control system. (00150b)

Controls and Indicators

General: Controls and Indicators

Read the CONTROLS AND INDICATORS section before
riding your motorcycle. Failure to understand the
operation of the motorcycle could result in death or
serious injury. (00043a)

Some features explained are unique to certain models. These features may be available as
accessories for your HarleyDavidson motorcycle. See a HarleyDavidson dealer for a complete
list of accessories that will fit your specific motorcycle.

Ignition/Headlamp Key Switch: Dyna Models

The automaticon headlamp feature provides increased
visibility of the rider to other motorists. Be sure headlamp
is on at all times. Poor visibility of rider to other motorists
can result in death or serious injury. (00030b)

See YOUR OWNER'S MANUAL section. Be sure to record all your key numbers in the space
provided at the front of this book.

See Ignition/Headlamp Key Switch: Dyna Models. The ignition/lamp key switch controls
electrical functions of the motorcycle.
Protect your vehicle against theft. After parking your
motorcycle, lock the steering head and remove ignition
key from switch. Failure to lock your motorcycle may
result in theft and/or equipment damage. (00151a)

Do not operate vehicle with forks locked. Locking the forks
restricts the vehicle's turning ability, which could result in
death or serious injury. (00035a)

Do not lubricate barrel locks with petroleum based
lubricants or graphite. Inoperative locks may result.
(00152a)

1. To remove the key from the ignition, push the key in and turn it counterclockwise.

2. Remove the key.
NOTES:

Refer to Ignition/Headlamp Key Switch: Dyna Models for key switch functions.
The lamps work when the switch is in the IGNITION position as required by law in some
localities.
On FXDC and FXDF models, remove the ignition key from the ignition lock while operating
the motorcycle. If you do not remove the key, it can fall out during operation.
Ignition/Headlamp Key Switch: Dyna Models

MODEL LOCATION AND OPERATION SWITCH FUNCTION

POSITION
FXD, On the right front of the motorcycle on OFF Ignition, lamps and accessories
FXDL, the steering head. are off.
FXDB
To unlock the switch and the front fork,
push the key in and turn it ACC* Accessories and hazard warning
counterclockwise. flasher can be turned on.
Instrument lamps are on. Brake
HDI: Press the lever/key (international) lamp and horn can be activated.
in and turn it clockwise to the OFF Key may be removed except on
position. Be sure to push key in to move international models.
key to either position.

Fork Lock: To lock the fork, move the
fork to the full left position. Push down
on key and turn it to the right, clockwise, IGNITION* Ignition, lamps and accessories
to the closed lock icon. Remove the are on.
key.
FXDC, Switch is on fuel tank instrument panel. OFF Ignition, lamps and accessories
FXDC, Switch is on fuel tank instrument panel. OFF Ignition, lamps and accessories
FXDF are off.
Switch is locked or unlocked by lifting
switch cover, inserting key and turning
key counterclockwise to lock or
clockwise to unlock. Key may be ACC* Accessories are on. Hazard
removed in any position. warning flashers can be operated.
Instrument lamps are on. Brake
Fork Lock: The fork lock is on the right lamp and horn can be activated.
front of the motorcycle on the steering
head. Insert key and press to turn the
lock to the closed lock icon. Remove the
key.
IGNITION* Ignition, lamps and accessories
To unlock the fork lock, insert key and are on.
press to turn the lock to the open lock
icon. Remove the key.
*International models have an additional function position lamp and tail lamp are also on.

1. Lock position
2. Unlock position
3. Open switch cover
4. OFF
5. ACC
6. Ignition
Ignition/Headlamp Key Switch: Dyna Models
1. Locked
2. Unlocked
Fork Lock: FXDC and FXDF Models

Fork Lock: Dyna Models

Protect your vehicle against theft. After parking your
motorcycle, lock the steering head and remove ignition
key from switch. Failure to lock your motorcycle may
result in theft and/or equipment damage. (00151a)

FXD, FXDL and FXDB: See Ignition/Headlamp Key Switch: Dyna Models. The fork lock is
incorporated with the Ignition/Headlamp Key Switch found on the right hand side of the steering
head. Refer to Ignition/Headlamp Key Switch: Dyna Models.

FXDC and FXDF: See Fork Lock: FXDC and FXDF Models. With the Ignition/Headlamp Key
Switch located on the console, only the fork lock is found in the right hand side steering head.

Do not operate vehicle with forks locked. Locking the forks
restricts the vehicle's turning ability, which could result in
death or serious injury. (00035a)

Using the fork lock immediately after parking your motorcycle will discourage unauthorized use or
theft when parking your motorcycle.

To Lock Fork
1. Turn fork to full left position.

2. Insert ignition key into fork lock.

3. Turn left (counterclockwise) to lock position.

4. Remove ignition key.

To Unlock Fork

1. Insert ignition key into fork lock.

2. Turn right (clockwise) to unlock position.

Hand Controls: Basic Operation

Electric Starter Switch

NOTE:

Off/Run switch MUST be in RUN position to operate engine.

See Handlebar Controls. The electric starter switch is located on the right handlebar control
group. See Starting the Engine for detailed operation procedures.

1. Put the engine off/run switch in the RUN position and the transmission in neutral. Neutral
(green) indicator lamp should be illuminated.

2. See Ignition/Headlamp Key Switch: Dyna Models. Turn ignition/headlamp key switch
to IGNITION and push the START switch to operate starter motor.

Engine OFF/RUN Switch

See Handlebar Controls. The engine off/run switch (7) turns the ignition power ON or OFF. The
engine off/run switch is located on the right handlebar control. Push the top portion of the engine
off/run switch to turn off ignition power and shut the engine off. Push the bottom portion of the
engine off/run switch to turn on ignition power.
NOTES:

The engine off/run switch must be in the RUN position to start or operate the engine.
The engine off/run switch should be used to shut the engine off.

1. To shut the engine off, push the top of the off/run switch to the ignition OFF position.

2. See Ignition/Headlamp Key Switch: Dyna Models. Turn the ignition key to the OFF
position to turn the ignition power completely OFF.

Throttle Control Grip

See Handlebar Controls. The throttle control grip (9) is located on the right handlebar control
and is operated with the right hand.

To reduce rider fatigue on long trips, a spring loaded throttle friction adjustment screw (10) is
located at the bottom of the throttle grip clamp on noncruise equipped models.

1. Slowly turn throttle control grip clockwise (toward the front of the bike) to close the throttle
(decelerate).

2. Slowly turn throttle control grip counterclockwise (toward rear of bike) to open the throttle
(accelerate).

Do not tighten throttle friction adjustment screw to the
point where the engine will not return to idle automatically.
Overtightening can lead to loss of vehicle control, which
could result in death or serious injury. (00031b)

3. Unscrew the throttle friction adjustment screw so the throttle returns to the idle position
when the hand is removed from the grip.

4. Screw the throttle adjustment screw in to increase friction on grip. This provides a damping
effect on throttle motion.
NOTE:

The throttle friction adjustment screw should not be used under normal stop and go operating
conditions.

Clutch Hand Lever

Do not position fingers between hand control lever and
handlebar grip. Improper hand positioning can impair
control lever operation and cause loss of vehicle control,
which could result in death or serious injury. (00032a)

See Handlebar Controls. The clutch hand lever (1) is located on the left handlebar and is
operated with the fingers of the left hand.

1. Slowly pull clutch hand lever in against handlebar grip to fully disengage clutch.

2. Shift to first gear using the gear shifter lever. See Shifting Gears: Six Speed.

3. Slowly release the clutch hand lever to engage clutch.

A clutch switch is incorporated into the left handlebar switch assembly. It enables the rider to start
the vehicle in any gear (or in neutral) as long as the clutch lever is pulled in. If the clutch is not
disengaged, the vehicle will not start.

Horn Switch
See Handlebar Controls. The horn is operated by pushing on the horn switch (2) located on the
left handlebar control group.

Headlamp Dimmer Switch

See Handlebar Controls. The headlamp dimmer switch (3) is located on the left handlebar. The
switch has two positions to activate the headlamps high or low beams.

Press the top of the headlamp dimmer beam switch to activate the high beam.
Press the bottom of the headlamp dimmer switch to return to the low beam.

See Indicator Lamps. The (blue) high beam indicator lamp will illuminate when the high beam is
on.

Turn Signal Switches

See Handlebar Controls. Each handlebar control group contains a turn signal switch.

The right turn signal switch (11) operates the right front and right rear flashing lamps.
The left turn signal switch (4) operates the left front and left rear flashing lamps.
NOTE:

Front turn signal lamps also function as running lamps (except International models).

1. Clutch hand lever
2. Horn switch
3. Headlamp dimmer switch
4. Left turn signal switch
5. Master cylinder reservoir
6. Electric starter switch
7. Engine off/run switch
8. Brake hand lever
9. Throttle control grip
10. Throttle friction adjusting screw
11. Right turn signal switch
Handlebar Controls

Turn Signal Switch Operation

The turn signal switches are used by the turn signal module to control turn signal operation based
on vehicle speed, vehicle acceleration and turn completion.
Momentarily depress the desired turn signal switch. The turn signal lamps will begin and continue
flashing until they are manually or automatically cancelled. As long as the motorcycle is
stationary, the signals will flash.
NOTES:

If you are signaling to turn in one direction and you depress the switch for the opposite turn
signal, the first signal is cancelled and the opposite side begins flashing.
If you want to stop the lamps from flashing, briefly depress the turn signal switch a second
time. The turn signal lamps will stop flashing.

Hazard Warning 4Way Flasher

Use the following method to activate the fourway flashers.

1. With the ignition key ON and security system disarmed (if equipped), press the left and right
turn signal switches at the same time.

2. Turn the ignition key OFF and arm the security system if present and desired. The fourway
flashers will continue for two hours.

3. To cancel fourway flashing, disarm the security system if necessary, turn the ignition key
ON and press the left and right turn signal switches at the same time.

This system allows a stranded vehicle to be left in the fourway flashing mode and secured until
help is found.

Indicator Lamps

See Indicator Lamps. Five indicator lamps are provided.

The green TURN indicators will flash when turn signals are activated; therefore, flashing
indicates the chosen turn direction. When the 4way hazard flashers are operating, both turn
indicators will flash simultaneously.
The blue BEAM indicator lamp, when lit, signals high beam headlamp operation.
The green NEUTRAL lamp, when lit, signals the transmission is in neutral gear.
The red OIL indicator lamp, when lit, signals that oil is not circulating through the engine.
NOTE:

The OIL indicator lamp will glow when the ignition is turned on prior to starting engine. With
engine running, lamp should be off when engine speed is above idle.

Several other circumstances that could cause the red oil indicator lamp to signal, include the
following:

If the oil pressure indicator lamp does not go off at speeds above idling, it is usually because
of an empty oil tank or diluted oil.
In freezing weather the oil feed may clog with ice and sludge, preventing oil circulation.
A grounded oil signal switch wire.
A faulty signal switch.
A damaged or improperly installed check valve.
Trouble with the pump.
If the oil pressure indicator lamp remains lit, always check
the oil supply first. If the oil supply is normal and the lamp
is still lit, stop the engine at once and do not ride further
until the trouble is located and the necessary repairs are
made. Failure to do so may result in engine damage.
(00157a)

1. Left turn
2. High beam
3. Neutral
4. Oil
5. Right turn
Indicator Lamps

Instruments: Dyna Models

Speedometer

Never attempt to tamper with or alter the vehicle odometer.
This is illegal. Tampering with or altering a vehicle
odometer may cause equipment damage. (00160a)

See Instruments: Dyna Models. The speedometer registers miles per hour (U.S. models) or
kilometers per hour (international models) of forward speed. The speedometer also provides the
following selectable functions:

Odometer
Trip odometers A and B
12 or 24 hour clock
The speedometer has a single display window for the above functions.

1. See Instruments: Dyna Models. Pressing the function switch with the ignition switch in
any position will activate the odometer reading and time. Time and mileage or kilometers
may be checked without unlocking ignition switch. Press and release function switch once to
view odometer. Press and release switch again to display time.

2. To check mileage on trip odometers, the ignition switch must be in the ACC or IGNITION
position. Press and release the function switch until the desired trip odometer reading is
displayed. An A or B in the upper left of the display window identifies trip odometers.

3. To reset or zero trip odometers, have desired (A or B) odometer in display window. Press
function switch and hold switch for 23 seconds. The trip odometer will be reset to zero.

4. Repeat the previous step if you wish to zero both trip odometers.

Setting Clock

1. Turn the ignition switch to ACC or IGNITION.

2. See Instruments: Dyna Models. Press function switch until time (hour and minutes) is
displayed. Press and hold the function switch for five seconds or until 12HR begins to blink
in the speedometer display window. Release the button.

3. Press and release the function switch once to advance to a blinking 24HR or military style
time display. Each time you press and release the button, the display will switch between
12HR and 24HR.

4. When the desired time style is displayed, press and hold the function switch for five
seconds. The display will switch to the time display with the hours blinking.
NOTE:

There is no AM or PM time setting required. So when correct hour is reached, press and
hold function switch to advance to minute setting.

5. Press and release the function switch repeatedly to advance the hours. Each time you press
and release the switch, the display will advance one hour.

6. When the correct hour is displayed, press and hold the function switch for five seconds. The
minutes display will start blinking.

7. Press and release the function switch repeatedly to advance the minutes display. Each time
you press and release the button, the display will advance one minute.

8. When the correct minutes are displayed, press and hold the function switch for five seconds.
The minutes display will stop blinking, indicating that the clock has been set.

9. Turn the ignition switch OFF.

Tachometer

See OPERATING RECOMMENDATIONS section. Do not
See OPERATING RECOMMENDATIONS section. Do not
operate the engine above maximum safe RPM as shown
under OPERATION (red zone on tachometer). Lower the
RPM by upshifting to a higher gear or reducing the amount
of throttle. Failure to lower RPM may cause equipment
damage. (00159a)

The tachometer registers the engine speed in revolutions per minute (RPM).

Tip Indicator Lamp

If tip occurs, check all controls for proper operation.
Restricted control movement can adversely affect the
performance of the brakes, clutch or ability to shift, which
could result in loss of vehicle control and death or serious
injury. (00350a)

Should motorcycle be tipped over, the word "tip" will appear in the odometer window. Engine will
not start until reset. To reset, cycle ignition/headlamp key switch ONOFFON.

Fuel Range Function

The fuel range function shows the approximate mileage available with the amount of fuel left in
the fuel tank.

1. With the ignition switch in the ACC or IGNITION position, press function switch until fuel
range function is displayed, as indicated by the letter 'r' in the left side of the odometer
display. The calculated remaining distance (miles or kilometers) to empty is displayed,
based on the amount of fuel in tank. Range can be accessed at any time using the function
switch.

2. When the low fuel warning lamp illuminates, the range feature will automatically be
displayed in the odometer unless this automatic popup feature is disabled by a press and
hold of the function switch while in range display mode. Automatic range popup feature will
show that it is disabled by blinking twice. Likewise, automatic range popup can be
reactivated by a press and hold of the function switch. Range will blink once when the
automatic popup feature is reenabled.
NOTE:
When the low fuel warning lamp turns on, there is approximately 0.90 gallon 3.41 liters
of fuel remaining in the tank. Refuel as soon as possible.
The range display is only updated when the vehicle is moving.

3. After the range calculation reaches 10 miles 16 kilometers remaining, the range display will
display "r Lo" to indicate that the vehicle will shortly run out of fuel.

4. Resetting the low fuel warning lamp and range requires an ignition cycle change.
1. Speedometer
2. Sixth gear lamp
3. Engine check lamp
4. Odometer/tripodometer
5. Low fuel warning lamp
6. Security system lamp
7. Battery discharge lamp
8. Fuel gauge
9. Tachometer
10. Function switch (back of gauge or side of console)
Instruments: Dyna Models

Warning Lamps

Engine Check Lamp

See Instruments: Dyna Models. The engine check lamp is located inside the instrument
cluster. Its purpose is to indicate whether or not the engine/engine management system is
operating normally. The engine lamp color is amber.

The engine lamp normally comes on when the ignition is first turned on and remains on for
approximately 4 seconds, as the engine management system runs a series of selfdiagnostics.

If the engine lamp comes on at any other time, see a HarleyDavidson dealer.

Low Fuel Lamp

See Instruments: Dyna Models. There is a low fuel warning lamp within the instrument cluster.
The low fuel lamp lights up to indicate that there is approximately 0.90 gallons 3.41 liters of
gasoline left in the tank. The low fuel lamp color is amber.

Battery Lamp

See Instruments: Dyna Models. The battery lamp indicates either overcharging or
undercharging of the battery. Refer to Battery: Dyna Models.

Security System Lamp
See Instruments: Dyna Models. The security system lamp will illuminate when the security
system is armed. Refer to HarleyDavidson Smart Security System

Gear Shift Lever

The clutch must be fully disengaged before attempting a
gear shift. Failure to fully disengage the clutch can result
in equipment damage. (00182a)

See Shift Pattern. The gear shift lever is located on the left side of the motorcycle and is
operated with the left foot. The transmission is a six speed sequential gear box.

1. Push the gear shift lever all the way down (full stroke) to shift the transmission to the next
lower gear.

2. Lift the gear shift lever all the way up (full stroke) to shift the transmission to the next higher
gear.
NOTES:
Release the gear shift lever after each gear change.
The lever must return to its central position before another gear change can be made.

First gear is the last gear position that can be found by pushing the gear shift lever full stroke
downward.

Neutral is located between first and second gear. The green neutral indicator lamp on the dash
will illuminate when the transmission is in neutral.

To shift from first gear to neutral, lift the gear shift lever 1/2 of its full stroke.

When the motorcycle is standing still and the engine is not running, shifting gears requires a
different technique. Before shifting in this condition, move the motorcycle backward and forward
with the clutch fully disengaged (clutch lever pulled in). While maintaining slight pressure on the
shift lever, shift from one gear to another.

Even with the engine running and the motorcycle standing still, difficulty may be experienced in
shifting gears. This difficulty occurs because transmission gears are not turning and shifting parts
are not lined up to permit engagement.

When difficulty of shifting gears is experienced, do not
under any circumstances, attempt to force the shift. The
results of such abuse will be a damaged or broken shifter
mechanism. (00161a)

See Shifting Gears: Six Speed for more information.
Shift Pattern

Brake System

Do not apply brake strongly enough to lock the wheel. A
locked wheel will skid and can cause loss of vehicle
control, which could result in death or serious injury.
(00053a)

The rear brake pedal controls the rear wheel brake and is located on the motorcycle's right side.
Operate the rear brake pedal with the right foot.

The front brake hand lever controls the front wheel brake and is located on the right handlebar.
Operate the hand lever with the fingers of the right hand.

Brakes should be applied uniformly and evenly to prevent wheels from locking up. A balance
between rear and front braking is generally best.

Jiffy Stand

Always park motorcycle on a level, firm surface. An
Always park motorcycle on a level, firm surface. An
unbalanced motorcycle can fall over, which could result in
death or serious injury. (00039a)

The jiffy stand is located on the left side of the motorcycle and swings outward to support the
motorcycle for parking.

Rear View Mirrors

Objects in mirrors are closer than they appear. Use caution
when judging distance of objects in mirrors. Failure to
judge correct distances could result in death or serious
injury. (00033a)

Your vehicle is equipped with two convex rear view mirrors.

This type of mirror is designed to give a much wider view to the rear than a flat mirror. However,
cars and other objects seen in this type of mirror will look smaller and farther away than they
actually are.

Use caution when judging the size or relative distance of objects seen in rear view mirrors.
Always adjust the rear view mirrors to clearly reflect the area behind the motorcycle before
riding.
NOTE:

Adjust mirrors so you can see a small portion of your shoulders in each mirror. This will help you
establish the relative distance of vehicles to the rear of your motorcycle.

Fuel Filler Cap: Dyna Models

All Models Except FXD
See Fuel Gauge and Fuel Filler Cap: Dyna Models (Except FXD). To open fuel filler cap,
turn cap counterclockwise and lift up. To close, turn fuel filler cap clockwise until it clicks. The
ratchet action of the cap prevents overtightening.
NOTES:

Fuel filler cap turns approximately a 3/4 turn before it starts unscrewing.
The fuel filler cap is located on the right side of the fuel tank. The cap on the left side is the
fuel gauge and is NOT removable.

FXD Models

See Fuel Gauge and Fuel Filler Cap: FXD Models. To open fuel filler cap, pull metal tab up
and turn knob counterclockwise and remove cap.

See SAFE OPERATING RULES and review safety procedures which follow.

Do not spill fuel onto the motorcycle while refueling.
Immediately wipe up fuel spills on your motorcycle. Fuel
can cause damage to cosmetic surfaces. (00147b)

Use only unleaded fuel in catalytic converterequipped
motorcycles. Using leaded fuel will damage the emission
control system. (00150b)

Do not use aftermarket fuel caps. Aftermarket fuel caps
may fit improperly and leak, which could lead to death or
serious injury. See a HarleyDavidson dealer for approved
fuel caps. (00034a)

1. Fuel gauge
2. Fuel filler cap
Fuel Gauge and Fuel Filler Cap: Dyna
Models (Except FXD)

1. Fuel gauge
2. Fuel filler cap
Fuel Gauge and Fuel Filler Cap: FXD Models

Rear Shock Preload Adjustment
Be sure both shock absorbers are adjusted to same
preload position. Improper adjustment can adversely affect
stability and handling, which could result in death or
serious injury. (00036a)

The rear shock absorber springs can be adjusted to five positions to compensate for various
loads.

For heavy loads, the springs should be compressed.
For lighter loads the springs should be extended.

See Rear Shock Absorber Spring Adjustment (Typical). To adjust the rear shock absorber,
turn spring adjusting cam to desired position with a SPANNER WRENCH HD9470052C . Both
spring adjusting cams must be adjusted to the same position. When returning to offcam position,
cams should be backed off in opposite direction.

Rear Shock Absorber Spring Adjustment (Typical)
Spanner Wrench (HD9470052C)

HandsFree Security Module

HarleyDavidson Smart Security System

Components

See Security Module w/Antenna (shown removed). The HarleyDavidson Smart Security
System (HDSSS) consists of a HandsFree Security Module (HFSM) (1) and a HandsFree
Antenna (2) mounted on the motorcycle, and a HandsFree Fob carried by the rider/passenger.

After parking the motorcycle, turn the ignition key to OFF and the Smart Security System will
automatically arm within five seconds. While armed, the starter and ignition are disabled and the
rider may leave the motorcycle knowing that the module will activate an alarm if someone tampers
with the ignition or attempts to move the motorcycle.

If the fob is present, the module will automatically disarm when the ignition key is turned to
IGNITION or ACCESS.
NOTE:

Do not relocate the module or the antenna on the motorcycle.

Options

Several options are available for the HarleyDavidson Smart Security System from the Harley
Davidson Genuine Motor Accessories and Motor Parts catalog. Options include:

Smart Siren and Smart Siren II.
Security Pager and Security Pager Receiver II.
Replacement Fobs.
See a HarleyDavidson dealer for details.

1. HandsFree Security Module
2. HandsFree Antenna
Security Module w/Antenna (shown
removed)

FCC Regulations

FCC ID: L2C0027TR IC ID: 3432A0027TR

FCC ID: L2C0028TR IC ID: 3432A0028TR

This device complies with Part 15 of the FCC Rules and with RSS210 of Industry Canada rules.
Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressively approved by the party responsible for
compliance could void the user's authority to operate the equipment.

The term "IC:" before the radio certification number only signifies that Industry Canada technical
specifications were met.

HandsFree Fob
Fob Assignment

See HandsFree Fob: Smart Security System. HandsFree Fobs are electronically assigned
to the HarleyDavidson Smart Security System by a HarleyDavidson dealer so that the module
can recognize a fob's unique signal. Only two fobs can be assigned to the module at any one
time.

Replacement fobs can be purchased from a dealership but can only be assigned to the
motorcycle by a trained HarleyDavidson technician.
NOTES:

The reusable label found on the fob packaging lists the serial number of the fob. For
reference, fix the label to a blank "NOTES" page in the Owner's Manual.
The serial number of the fob is also found on the inside of the fob. See Fob Battery.
The module will arm only if the fob has been assigned by a HarleyDavidson dealer and a
Personal Identification Number (PIN) has been entered in the system. The PIN should be
recorded on the Personal Information page in the front of this Owner's Manual and on the
removable wallet card.
Should the rider misplace the fob or if the fob fails, the rider can refer to the wallet card and
use the PIN to manually disarm the system. Refer to Arming and Disarming and
Troubleshooting.
The PIN can easily be changed by the rider at any time. Refer to Personal Identification
Number (PIN).

HandsFree Fob: Smart Security System

Riding with a Fob
Always carry the fob when riding, loading, fueling, moving, parking or servicing the
motorcycle. Carry the fob in a convenient pocket.
Do not leave the fob attached to the handlebars or store the fob in a saddlebag or Tour
Pak®. Unintentionally leaving the fob with the motorcycle when it's parked prevents the
system from activating the alarm.
Do not ride with the fob stored in a metal case or with the fob closer than 3.0 in. 76 mm to a
cell phone, PDA, display or other electronic device. Any electromagnetic interference may
prevent the fob from disarming the system.
For added security, always lock the fork and remove the ignition key when parked. If the fob
is within range and the motorcycle is unlocked, tampering with the motorcycle will not
activate the alarm.

Personal Identification Number (PIN)

The Personal Identification Number (PIN) is a number that can be used to disarm the Harley
Davidson Smart Security System in case an assigned fob is misplaced, fails or if the fob and
module cannot communicate because of electromagnetic interference.

A PIN is a fivedigit number (19, no zeros).

Changing the PIN

To maintain security, the rider can change the PIN at any time. Refer to Changing the PIN.

Changing the PIN

STEP ACTION WAIT FOR CONFIRMATION NOTES

NO.
1 Select a 5digit (1 thru 9) PIN
and record on the wallet card
from Owner's Manual.
2 With an assigned fob present,
turn IGN key IGNITIONOFF
IGNITIONOFFIGNITION.
3 Press left turn signal switch 3
times.
4 Press right turn signal switch Turn signals will flash 3 times. See figure showing the
1 time and release. Current PIN will appear in odometer window with
odometer. The first digit will be PIN display.
flashing.
5 Enter first digit (a) of new PIN
by pressing left turn signal
switch a times.
6 Press right turn signal switch The new digit (a) will replace the
1 time and release. current in odometer window.
7 Enter second digit (b) of new
PIN by pressing left turn
signal switch b times.
8 Press right turn signal switch The new digit (b) will replace the
1 time and release. current in odometer window.
9 Enter third digit (c) of new PIN
by pressing left turn signal
switch c times.
10 Press right turn switch 1 time The new digit (c) will replace the
and release. current in odometer window.
11 Enter fourth digit (d) of new
PIN by pressing left turn
signal switch d times.
12 Press right turn switch 1 time The new digit (d) will replace the
and release. current in odometer window.
13 Enter fifth digit (e) of new PIN
by pressing left turn signal
switch e times.
14 Press right turn switch 1 time The new digit (e) will replace the
and release. current in odometer window.
15 Before the module rearms, The odometer will return to Turning the ignition
turn the ignition key to OFF. mileage. key to OFF stores the
new PIN in the
module.

1. Current PIN (example) on PIN Change
2. PIN Disarm
Odometer Windows PIN

Security Status Indicator

See Security Status Indicator. The illuminated key icon in the speedometer face indicates the
status of the HarleyDavidson Smart Security System.
Armed: A key icon that blinks approximately every 3 seconds indicates that the system is
armed.
Disarmed: After the ignition/headlamp switch is turned to IGNITION and the system
disarms, the key icon will remain illuminated for approximately four seconds and then turn
off.
Service: A key icon that remains illuminated longer than four seconds indicates that service
of the module is required.

Security Status Indicator

Arming and Disarming

Arming

When the motorcycle is parked and the ignition key is turned to OFF, the HarleyDavidson Smart
Security System arms automatically within five seconds if no motion is detected. Even when the
fob is present, the system will arm.

On arming, the turn signals will flash twice and the optional siren will chirp twice. While armed, the
key icon in the speedometer face will flash every three seconds.
NOTE:

International Models: The HFSM must be in the Chirp Mode for the siren to chirp on arming or
on disarming. See Siren Chirp Mode (Confirmation).

Disarming

Once disarmed, the rider may ride or move the motorcycle for parking, storage or service without
setting off the alarm.
Fob: An armed Smart Security System is automatically disarmed when the ignition key is turned
to IGNITION with the fob present.

When the module disarms, the optional siren will chirp once and the key icon will illuminate for a
solid four seconds and then turn off.
NOTE:

Any motion, like lifting the motorcycle up off of its jiffy stand, or turning the ignition key to
IGNITION and the module will electronically "poll" for the presence of the fob. If the fob is present,
the system disarms.

Personal Identification Number (PIN): If the fob is misplaced or if the present fob fails to
communicate with the module, the system can be disarmed with the Personal Identification
Number (PIN).

Disarming with a PIN

Do not turn handlebars, straddle seat or lift motorcycle off the jiffy stand. During a PIN disarm, if
the Smart Security System detects motorcycle motion the system will activate the alarm.

Entering a PIN to Disarm HarleyDavidson Smart Security System

STEP ACTION WAIT FOR CONFIRMATION NOTES

NO.
1 If necessary, verify the Should be recorded on wallet
current 5digit PIN. card.
2 Turn ignition key to
IGNITION.
3 Quickly (within 2 seconds Key icon flashes at fast rate. See figure showing the
of turning ignition key) hold In the odometer window, a odometer window with PIN
both turn signal switches in flashing dash will be followed display. Five dashes will
until confirmation. by four more dashes. appear in the odometer
window.
4 Enter first digit (a) in the The first digit (a) in the
PIN by pressing left turn odometer will be the first digit
switch a times. in the PIN.
5 Press right turn switch 1 The first digit is stored and Serves as enter key.
time. the dash will flash.
6 Enter second digit (b) in the The second digit (b) in the
PIN by pressing left turn odometer will be the second
switch b times. digit in the PIN.
7 Press right turn switch 1 The second digit is stored Serves as enter key.
time. and the next dash will flash.
8 Enter third digit (c) in the The third digit (c) in the
PIN by pressing left turn odometer will be the third
switch c times. digit in the PIN.
9 Press right turn switch 1 The third digit is stored and Serves as enter key.
time. the next dash will flash.
10 Enter fourth digit (d) in the The fourth digit (d) in the
PIN by pressing left turn odometer will be the fourth
switch d times. digit in the PIN.
11 Press right turn switch 1 The fourth digit is stored and Serves as enter key.
time. the next dash will flash.
12 Enter fifth digit (e) in the The fifth digit (e) in the
PIN by pressing left turn odometer will be the fifth digit
switch e times. in the PIN.
13 Press right turn switch 1 The fifth digit is stored. The Smart Security System is
time. key icon stops blinking. disarmed.

NOTES:

At any time during a PIN disarm, if the fob is brought within range of the motorcycle, the
Smart Security System will disarm when the module receives the coded signal from the fob.
If a mistake is made while entering PIN, wait two minutes before another disarming attempt.
The Smart Security System will remain disarmed until the ignition key is turned to OFF.

Arming with Hazard Warning 4Way Flashers On

If it should be necessary to leave a motorcycle parked along side a roadway, the hazard warning
fourway flashers can be turned ON and the Smart Security System armed.

1. Turn ignition key to IGNITION.

2. Simultaneously press both left and right turn signal switches to turn the fourway flashers
ON.

3. Turn the ignition key to OFF to arm the Smart Security System.

To turn hazard warning flashers OFF, turn the ignition key to IGNITION and simultaneously press
the left and right turn signal switches.

Alarm

Warnings

Once armed, if the motorcycle is moved or lifted up off of its jiffy stand or if the ignition key is
turned to IGNITION and the fob is not present, the alarm will warn the operator with three
alternate flashes of the turn signals and a chirp of the optional siren.

Within four seconds, if the motorcycle is back on its jiffy stand and no further motion is detected
and/or the ignition key is turned to OFF, the module will remain armed without activating the
alarm.

If the motorcycle motion continues or the ignition key is not turned back to OFF, the module will
issue a second warning four seconds after the first.
NOTE:

During warnings and alarms, the starter motor and the ignition circuits are disabled.
The Alarm

If the Smart Security System is still detecting motion and/or if the ignition key has not been turned
back to OFF after a second warning, the system will activate the alarm.

When activated, the Smart Security System will:

Alternately flash the four turn signals.
See Optional Smart Siren. Sound the optional siren.

Duration: The alarm will stop within 30 seconds and if no motion is detected, the alarm will not
restart.

However, if motorcycle motion continues the system will repeat the 30 second alarm and recheck
for motion. The alarm will repeat this 30 second alarm cycle for five minutes (10 cycles) or until
the alarm is deactivated.
NOTE:

The alarm will also activate the LED, vibration or audible modes of a HarleyDavidson Security
Pager. A pager can operate either in silent or in combination with an optional Smart Siren. The
range of a pager can be up to 0.5 mile 0.8 km . See a HarleyDavidson dealer for details.

Optional Smart Siren

Deactivate the Alarm

Key Fob: Bring the fob to the motorcycle. After the module identifies that the fob is present, the
system will terminate the alarm.

Siren Chirp Mode (Confirmation)

Chirpless Mode
In the chirpless mode, the siren does not chirp on arming or disarming.
NOTE:

Even when armed in the chirpless mode, the siren still chirps warnings on movement and will
activate the alarm through cycles.

Chirp Mode

On arming in the chirp mode, the siren responds with two chirps. When disarming, the siren
responds with a single chirp.

Switching Modes

Cycling quickly through two armings and disarmings will switch the system from either the
chirpless mode or the chirp mode to its opposite.

1. With the fob present, the ignition switch to ON and the system disarmed, turn the ignition
switch OFF.

2. When the system arms (2 flashes of turn signals), immediately turn the ignition switch to
ON.

3. Wait until the security lamp goes out, then immediately turn the ignition switch OFF.

4. When the system arms (2 flashes of turn signals), immediately turn the ignition switch to ON
and wait for system to disarm.

Transport Mode

It is possible to arm the security system without enabling the motion detector for one ignition
cycle. This allows the vehicle to be picked up and moved in an armed state, however, any attempt
to start the engine will trigger the alarm.

To Enter Transport Mode

1. Turn the Ignition Switch to IGNITION.

2. Set the Engine Stop Switch to OFF.

3. With an assigned fob within range, turn the Ignition Switch from IGNITION to ACC.

4. Simultaneously press both the left and the right turn signal switches. This must be done
within five seconds of turning the Ignition Switch to ACC.

5. After the turn signals flash once, turn the Ignition Switch to OFF and the module is armed.

6. Confirmation: Turn signal blinks three times when armed for one ignition cycle.

To Exit Transport Mode
Return the system to normal operation:

With the fob present, turn the Ignition Switch to IGNITION to disarm the HFSM. To cancel the
transport mode, set the Engine Stop Switch to RUN.

Storage and Service Departments

Long Term Parking

To maintain arming, store the fob beyond the range of the module. If the motorcycle is to be
moved while parked, have the fob present.

If the motorcycle will not be operated for several months, such as during the winter season, follow
the Owner's Manual instructions for storage. Refer to Motorcycle Storage.

Service Departments

When the motorcycle is to be left at a HarleyDavidson dealer, there are two options:

1. Leave an assigned fob with the dealer.

2. To maintain possession of the fob, ask the dealer to disable the module for service (service
mode) before leaving the dealership.

Fob Battery

Replacing the Battery

Replace the key fob battery every year.

1. See HandsFree Fob Battery. Slowly turn a thin blade in the thumbnail slot (1) on the side
of the fob to separate the two halves.

2. Remove the battery (2) and discard.
NOTE:

Dispose of the old battery in accordance with local regulations.

3. Install a new battery (Panasonic 2032 or equivalent) with the positive (+) side down.

4. Align the two halves of the fob and snap together.
1. Thumbnail slot
2. Battery
3. Fob serial number
HandsFree Fob Battery

Power Disconnects

Optional Siren

On a power disconnect, to prevent the module from actuating the optional siren:

1. Verify that the fob is present.

2. Turn the ignition key to IGNITION.

3. Pull the main fuse from its holder or disconnect the battery.

Troubleshooting

Key Icon

If the system key icon stays illuminated while riding, see a HarleyDavidson dealer.

Fob

With the fob present, if the Smart Security System continues to actuate warnings and alarms, one
of the following can be the cause:

1. Electromagnetic Interference: Other electronic devices, power lines, or other
electromagnetic sources can cause the Smart Security System to operate inconsistently.

a. Verify that the fob is not in a metal enclosure or within 3.0 in. 76 mm of any other
electronic devices.

b. Place the fob on the seat and turn the ignition key to IGNITION. After the module
disarms, return the fob to a convenient location.

c. Move motorcycle at least 15 feet 5 m from the spot of interference.

2. Discharged Fob Battery: Use the PIN to disarm the module. Replace the battery. Refer to
Fob Battery.

3. A Damaged Fob: Use the PIN to disarm the motorcycle. Replacement fobs are available for
purchase from a HarleyDavidson dealer.

Siren

If the siren does not chirp two or three times on a valid arming command from the security
module, the siren is either in the Chirpless Mode, not connected, not working, or the siren
wiring was opened or shorted while the siren was disarmed.
If the siren is armed and the internal siren battery is dead, shorted, disconnected, or has
been charging for a period longer than 24 hours, the siren will respond with three chirps on
arming instead of two.
The internal siren battery may not charge if the vehicle's battery is less than 12.5 volts.
If the siren enters the selfdriven mode where it is powered from the siren's internal 9 volt
battery, the turn signal lamps may or may not alternately flash. If the security module
activates the siren, the turn signal lamps will alternately flash. If the siren has been armed
and a security event occurs, and the siren is in selfdriven mode, the siren will alarm for 20
to 30 seconds and then turn off for 5 to 10 seconds. This alarm cycle will be repeated ten
times if the siren is in the selfdriven mode.

Operation

Operating Recommendations: Dyna Models

Motorcycles are different from other vehicles. They
operate, steer, handle and brake differently. Unskilled or
improper use could result in loss of control, death or
serious injury. (00556c)

Take a rider training course.
Read Owner's Manual before riding, adding accessories or servicing.
Wear a helmet, eye protection and protective clothing.
Never tow a trailer.
Do not run the engine at extremely high RPM with clutch
disengaged or transmission in neutral. Running an engine
at high RPM can result in engine damage. (00177a)

The maximum recommended safe engine speed is 5500 RPM.
Do not idle engine unnecessarily for more than a few minutes with motorcycle standing still.

Do not exceed the maximum safe RPM specified below
under any conditions. Exceeding the maximum safe
engine RPM can result in equipment damage. (00248a)

NOTE:

The maximum recommended engine speed for Dyna model motorcycles is 5500 RPM.

Aircooled engines require air movement over the
cylinders and heads to maintain proper operating
temperature. Extended periods of idling or parade duty can
overheat the engine, resulting in serious engine damage.
(00178a)

An engine running long distances at high speed must be given closer than ordinary attention to
avoid overheating and possible engine damage.

This applies particularly to a motorcycle equipped with windshield and fairing.
NOTE:

Have the engine checked regularly and keep it well tuned.

When riding on wet roads, brake efficiency and traction are
greatly reduced. Failure to use care when braking,
accelerating or turning on wet roads can cause loss of
control, which could result in death or serious injury.
(00041a)

NOTE:

When descending upon a long, steep grade, downshift and use engine compression together with
intermittent application of both brakes to slow the motorcycle.

Continuous use of brake causes overheating and reduced
efficiency, which could result in death or serious injury.
(00042a)

Do not coast for long distances with the engine off or
idling. The transmission is properly lubricated only when
the engine is running. Coasting long distances can result
in transmission damage. (00180b)

Do not tow a disabled motorcycle. Towing can adversely
affect stability and handling, which could result in death or
serious injury. (00017a)

Breakin Riding Rules

The First 500 Miles (800 Kilometers)

The sound design, quality materials, and workmanship that are built into your new Harley
Davidson will give you optimum performance right from the start.

To allow your engine to wear in its critical parts, we recommend that you observe the riding rules
provided below for the first 500 miles 800 kilometers . Adherence to these suggestions will help to
assure good future durability and performance.

1. During the first 50 miles 80 kilometers of riding, keep the engine speed below 4000 RPM in
any gear. Do not lug the engine by running or accelerating at very low RPM, or by running at
high RPM longer than needed for shifting or passing.
NOTE:

For models without a tachometer, operate the motorcycle according to the speeds given in
Upshift (Acceleration) Gear Speeds: Six Speed and Downshift (Deceleration)
Gear Speeds: Six Speed during motorcycle breakin.

2. Up to 500 miles 800 kilometers , vary the engine speed and avoid operating at any steady
engine speed for long periods. Engine speed up to 5000 RPM in any gear is permissible.

3. Drive slowly and avoid fast starts at wide open throttle until the engine has warmed up.

4. Avoid lugging the engine by not running the engine at very low speeds in higher gears.

5. Avoid hard braking. New brakes need to be brokenin by moderate use for the first 200
miles 300 kilometers .

PreRiding Checklist

Read the CONTROLS AND INDICATORS section before
riding your motorcycle. Failure to understand the
operation of the motorcycle could result in death or
serious injury. (00043a)

Before riding your motorcycle at any time, make a general inspection to be sure it is in safe riding
condition.

1. Verify fuel is present in tank and add fuel if required.

2. Adjust mirrors to proper riding positions.

3. Verify oil is present in oil tank.

4. Check controls to make sure they operate properly. Operate the front and rear brakes,
throttle, clutch and shifter. All controls should operate freely without binding.

5. Check steering for proper operation by turning the handlebars through the full operating
range. Handlebars should turn smoothly without binding.

Be sure tires are properly inflated, balanced and have
adequate tread. Inspect your tires regularly and see a
HarleyDavidson dealer for replacements. Riding with
excessively worn, unbalanced or underinflated tires can
adversely affect stability and handling, which could result
in death or serious injury. (00014a)
6. Check tire condition and pressure. Incorrect pressure will result in poor riding characteristics
and can affect handling and stability. Refer to tire specifications for correct inflation pressure
to use.

Be sure headlamp, tail and stop lamp and turn signals are
operating properly before riding. Poor visibility of rider to
other motorists can result in death or serious injury.
(00478b)

7. Check all electrical equipment and switches including the headlamp, stop lamp, turn signals
and horn for proper operation.

8. Check for any fuel, oil or hydraulic fluid leaks.

9. Check secondary belt for wear or damage.

10. Service your motorcycle as necessary.

Jiffy Stand Interlock: International Models

Some international models are equipped with a jiffy stand interlock feature.

If the rider attempts to start the engine or pushes the starter button while the transmission is in
gear and the jiffy stand is down, then the jiffy stand interlock system will not permit the engine to
run. The message "SidE StAnd" will scroll across the odometer to indicate this to the rider.
Raising the jiffy stand (or putting the transmission in neutral) will permit the engine to run and
clear the message.

If the jiffy stand falls out of the fully retracted position while riding at speeds greater than 10 mph
15 km/h , then the jiffy stand interlock system will maintain engine operation and alert the rider
about this by illuminating the indicators (flash twice) and scroll the message "SidE StAnd" across
the odometer. The message will remain until the system detects the jiffy stand in the fully
retracted position again. The rider may continue to operate the vehicle while in this mode.

The rider may clear the text messages at any time by pressing the function switch once while the
vehicle is powered up.
NOTE:

If the operation of raising the jiffy stand and putting the transmission in gear is rapidly executed,
the jiffy stand bouncing off the frame could cause the jiffy stand interlock system to activate and
stop the engine.

Engine Idle Temperature Management System

For those riders who frequently find themselves in riding conditions where the vehicle is subjected
to prolonged idle conditions or traffic congestion, an optional dealer enabled engine calibration is
available. This calibration offers limited rear cylinder cooling with the vehicle stopped while the
engine is left at idle. This option is available for original equipment engine calibrations only. See
your dealer for details.

Starting the Engine
General

The engine should be allowed to run slowly for 1530
seconds. This will allow the engine to warm up and let oil
reach all surfaces needing lubrication. Failure to comply
can result in engine damage. (00563b)

Do not roll the throttle before starting. Rolling the throttle before starting the motorcycle is
unnecessary.

Starting

Shift transmission to neutral before starting engine to
prevent accidental movement, which could result in death
or serious injury. (00044a)

1. Turn ignition/headlamp key switch to IGNITION position. Do not roll the throttle.
NOTE:

The engine lamp will light for approximately 4 seconds and you will hear the fuel pump purr
for approximately 2 seconds as it operates to fill the fuel lines with gasoline.

2. See Right Handlebar Controls. Turn the off/run switch to RUN position.

3. Pull in clutch lever.
NOTE:

To activate the starting system, the clutch interlock circuitry requires that the clutch be
disengaged. The clutch lever must be pulled in against the left handlebar grip and/or the
transmission must be shifted to the neutral position (with the green neutral lamp lit).

4. Raise the jiffy stand (required on international models).

5. Press the starter button to start the motorcycle.

6. When the engine has started, you can operate your motorcycle as you normally would after
raising the jiffy stand.
NOTE:

If the fuel tank becomes completely dry, it may take a few seconds longer to start the motorcycle
after filling the tank. It will not be necessary to take any extraordinary measures before starting the
motorcycle.
1. Engine off/run switch
2. Engine start switch
Right Handlebar Controls

Stopping the Engine

1. Stop the engine by turning OFF the engine stop switch on right handlebar.

2. Turn OFF the ignition/headlamp key switch. If the engine should be stalled or stopped in any
way, turn off the ignition/headlamp key switch at once to prevent battery discharge.

Shifting Gears: Six Speed

Getting Started

The clutch must be fully disengaged before attempting a
gear shift. Failure to fully disengage the clutch can result
in equipment damage. (00182a)
NOTE:

Always start engine with transmission in neutral. Always start motorcycle forward motion from first
gear.

1. With motorcycle engine running and jiffy stand retracted, pull the clutch hand lever in against
handlebar grip to fully disengage clutch.
2. Push the foot shift lever down to end of its travel and release. The transmission is now in
first gear.

3. To start forward motion, release the clutch lever slowly to engage the clutch and at the same
time, open throttle gradually.

Upshift (Acceleration)

Refer to Upshift (Acceleration) Gear Speeds: Six Speed. Gear shift pattern is first gear
down, next five gears up. Engage second gear after the motorcycle has reached at the
appropriate shifting speed.

1. Close the throttle.

2. Disengage the clutch (pull clutch lever in).

3. See Upshift Pattern: Six Speed. Lift the gear shift lever up to the end of its travel and
release.

4. Engage the clutch (release clutch lever) and gradually open the throttle.

5. Repeat the previous steps to engage third, fourth, fifth, and sixth gears.
NOTES:

Disengage the clutch completely before each gear change.
Partially close the throttle so the engine will not drag when clutch is again engaged (clutch
lever released).

Upshift Pattern: Six Speed

Upshift (Acceleration) Gear Speeds: Six Speed

GEAR CHANGE MPH KPH

First to second 15 25
Second to third 25 40
Third to fourth 35 55
Fourth to fifth 45 70
Fifth to sixth 55 85

Downshift (Deceleration)

Do not downshift at speeds higher than those listed in the
Changing Gear Speeds table. Shifting to lower gears when
speed is too high can cause the rear wheel to lose traction
and lead to loss of vehicle control, which could result in
death or serious injury. (00045a)

See Downshift Pattern: Six Speed. Gear shift pattern is first gear down; next five gears up.
Refer to Downshift (Deceleration) Gear Speeds: Six Speed for shifting speeds.
NOTE:

The shifting speeds shown in the tables constitute a recommendation. Vehicle owners may
determine that individual shifting habits may differ from those stated and remain appropriate for
individual riding styles.

See Downshift Pattern: Six Speed. When engine speed decreases, as in climbing a hill or
running at a reduced speed, shift to the next lower gear while partially closing the throttle so the
engine accelerates as soon as the clutch lever is released.
NOTES:

Disengage the clutch completely before each gear change.
Partially close the throttle so the engine will not drag when clutch is again engaged (clutch
lever released).

Shift to neutral before stopping engine. Shifting
mechanism can be damaged by shifting gears while
engine is stopped. (00183a)

The gear shifter mechanism permits shifting the transmission to neutral from first gear.
Downshift Pattern: Six Speed

Downshift (Deceleration) Gear Speeds: Six Speed

GEAR CHANGE MPH KPH

Sixth to fifth 50 80
Fifth to fourth 40 65
Fourth to third 30 50
Third to second 20 30
Second to first 10 15

Maintenance and Lubrication

Safe Operating Maintenance

Good maintenance creates a safe motorcycle. A careful check of certain equipment must be
made after periods of storage. Also, frequently inspect the motorcycle between the regular service
intervals to determine if additional maintenance is necessary.

Check the following items:

1. Tires for correct pressure, abrasions or cuts.
2. Belt and primary chain for proper tension, wear or damage.

3. Brakes, steering and throttle for responsiveness and freedom from binding.

4. Brake fluid level and condition. Hydraulic lines and fittings for leaks. Also, check brake pads
and discs for wear.

5. Cables for fraying or crimping and free operation.

6. Engine oil and primary chaincase/transmission fluid levels.

7. Headlamp, tail lamp, brake lamp and turn signals for proper operation.

Breakin Maintenance

NOTE:

The performance of new motorcycle initial service is required to keep your new motorcycle
warranty in force and to assure proper emissions system operation.

Refer to Regular Service Intervals: 2009 Dyna Models. After a new motorcycle has been
ridden its first 1000 miles 1600 kilometers , it should be taken to an authorized HarleyDavidson
dealer for initial service operations.

Engine Lubrication

Do not switch lubricant brands indiscriminately because
some lubricants interact chemically when mixed. Use of
inferior lubricants can damage the engine. (00184a)

Engine oil is a major factor in the performance and service life of the engine. Always use the
proper grade of oil for the lowest temperature expected before the next scheduled oil change.
Refer to Recommended Engine Oils. Your authorized dealer has the proper oil to suit your
requirements.

If it is necessary to add oil and HarleyDavidson oil is not available, use an oil certified for diesel
engines. Acceptable diesel engine oil designations include: CF4, CG4, CH4 and CI4.

The preferred viscosities for the diesel engine oils in descending order are: 20W50, 15W40 and
10W40.

At the first opportunity, see an authorized dealer to change back to 100 percent HarleyDavidson
oil.

Recommended Engine Oils

HD TYPE VISCOSITY HD LOWEST AMBIENT COLD WEATHER STARTS

RATING TEMPERATURE BELOW 50° F (10° C)
HD Multi SAE HD 360 Below 40° F 4° C Excellent
grade 10W40
HD Multi SAE HD 360 Above 40° F 4° C Good
grade 20W50
HD Regular SAE 50 HD 360 Above 60° F 16° C Poor
HD Regular SAE 50 HD 360 Above 60° F 16° C Poor
Heavy
HD Extra SAE 60 HD 360 Above 80° F 27° C Poor
Heavy

Checking and Adding Oil

Oil level cannot be accurately measured on a cold engine.
For preride inspection, with motorcycle leaning on jiffy
stand on level ground, oil should register on dipstick
between arrows when engine is cold. Do not add oil to
bring the level to the FULL mark on a COLD engine.
(00185a)

See Dipstick Location: Dyna Models. Dipstick is located on lower right side of engine.

Oil Level Cold Check

Perform engine oil level COLD CHECK as follows:

1. See Dipstick Location: Dyna Models. For preride inspection with the vehicle resting on
the jiffy stand on level ground, unscrew and remove engine oil filler cap. Wipe off the
dipstick and insert it back into the oil pan with the cap screwed completely into the fill spout.

2. See Engine Oil Dipstick. Remove the dipstick and note the level of the oil. Oil level should
register between the two marks on the dipstick. If oil level is at or below the lower arrow, add
only enough oil to bring the level in the middle of the two marks (1) on the dipstick.
NOTE:

Clean oil from dipstick threads. If oil is present on threads, it can weep past the dipstick o
ring. This condition may be incorrectly diagnosed as an oil leak.

3. Replace filler cap and screw in securely.

Oil Level Hot Check

Perform engine oil level HOT CHECK as follows:

1. Ride motorcycle until engine is at normal operating temperature.

2. With the vehicle resting on the jiffy stand on level ground, allow engine to idle for 12
minutes. Turn engine off.

3. Remove and wipe off the dipstick. Insert it back with the cap screwed completely into the
filler neck.

4. Refer to Recommended Engine Oils. Remove the dipstick and note the level of the oil.
Add only enough oil to bring the level to the FULL mark on the dipstick. Do not overfill. Use
only recommended oil specified in Engine Lubrication.

5. Replace filler cap and screw in securely.
NOTE:

The engine will require a longer warm up period in colder weather.

Do not allow hot oil level to fall below Add/Fill mark on
dipstick. Doing so can result in equipment damage and/or
equipment malfunction. (00189a)

Do not overfill oil tank. Doing so can result in oil carryover
to the air cleaner leading to equipment damage and/or
equipment malfunction. (00190a)

Check engine oil supply at each complete fuel refill.
Refer to Regular Service Intervals: 2009 Dyna Models for recommended oil change
intervals.

Dipstick Location: Dyna Models
1. Lower arrow (add oil)
2. Cold check level
3. Upper arrow (hot check level)
Engine Oil Dipstick

NOTE:

See Engine Oil Dipstick. For cold check level, do not exceed midpoint on dipstick when filling
with oil.

Changing Oil and Filter

Do not switch lubricant brands indiscriminately because
some lubricants interact chemically when mixed. Use of
inferior lubricants can damage the engine. (00184a)

Be sure that no lubricants or fluids get on tires, wheels or
brakes when changing fluid. Traction can be adversely
affected, which could result in loss of control of the
motorcycle and death or serious injury. (00047d)

Twin Cam 96™ equipped vehicles require the premium oil filter (Part No. 6379899A Chrome or
Part No. 6373199A Black).
Engine Oil Drain Plug (oil pan under transmission, view from left side of vehicle)

1. Ride motorcycle until engine is warmed up to normal operating temperature.

2. See Dipstick Location: Dyna Models. Unthread the cap to remove the oil filler
plug/dipstick.

3. See Engine Oil Drain Plug (oil pan under transmission, view from left side of
vehicle). Remove the engine oil drain plug with oring. Allow oil to completely drain into a
suitable container.

Use HarleyDavidson oil filter wrench for filter removal.
This tool can prevent damage to crankshaft position
sensor and/or sensor cable. (00192b)

4. See Oil Filter Wrench (Part No. HD42311). Remove the oil filter using the OIL FILTER
WRENCH HD42311 or OIL FILTER WRENCH HD44067 . Clean the oil filter mount flange
of any old gasket material.
NOTE:

Dispose of oil and oil filter in accordance with local regulations.

5. See Applying Thin Oil Film. Lube the gasket on new oil filter with engine oil and install
new filter. Hand tighten oil filter 1/23/4 turn after gasket contacts filter mounting surface.

6. See Engine Oil Drain Plug (oil pan under transmission, view from left side of
vehicle). Install oil tank drain plug.

a. Inspect oring for tears or damage. Replace if required. Wipe any foreign material from
plug.

b. Install oring and drain plug and tighten to 1421 ftlbs (19.028.5 Nm).
Do not overfill oil tank. Doing so can result in oil carryover
to the air cleaner leading to equipment damage and/or
equipment malfunction. (00190a)

7. Refer to Recommended Engine Oils. Fill oil pan with the correct amount of oil. Use the
proper grade of oil for the lowest temperature expected before next oil change. Use 2.5
quarts 2.4 liters of engine oil for a capacity refill.

8. Check engine oil level using COLD CHECK procedure.

9. Start engine and carefully check for oil leaks around drain plug and oil filter.

10. Check engine oil level using HOT CHECK procedure.

Oil Filter Wrench (Part No. HD42311)
1. Thin oil film ONLY
2. Oil filter
3. Mounting plate
Applying Thin Oil Film

Winter Lubrication

In colder climates, the engine oil should be changed often. If motorcycle is used frequently for
short trips, less than 15 miles 24 kilometers , in ambient temperatures below 60° F 16° C , oil
change intervals should be reduced to 1500 miles 2400 kilometers . Motorcycles used only for
short runs must have a thorough tank flushout before new oil is put in. The tank flushout should
be performed by an authorized dealer or qualified technician.
NOTE:

The further below freezing the temperature drops, the shorter the oil change interval should be.

Water vapor is a normal byproduct of combustion in any engine. During cold weather operation,
some of the water vapor condenses to liquid form on the cool metal surfaces inside the engine. In
freezing weather this water will become slush or ice and, if allowed to accumulate too long, may
block the oil lines and cause damage to the engine.

If the engine is run frequently and allowed to thoroughly warm up, most of this water will become
vapor again and will be blown out through the crankcase breather.

If the engine is not run frequently and allowed to thoroughly warm up, this water will accumulate,
mix with the engine oil and form a sludge that is harmful to the engine.

Transmission Lubrication
Refer to Regular Service Intervals: 2009 Dyna Models. The transmission should be drained
and refilled with fresh lubricant at proper intervals.

The transmission lubricant level should be checked monthly.

Checking and Adding Transmission Lubricant

NOTE:

When checking the transmission lubricant level, the motorcycle should be turned off and leaning
on its jiffy stand on a level surface. Allow a short period of time to equalize lubricant level in the
transmission compartments.

1. Check the transmission lubricant level with engine turned off and motorcycle resting on jiffy
stand on level surface.

2. See Transmission Filler Plug/Dipstick Location. Unscrew and remove transmission
lubricant filler plug with attached dipstick. Wipe dipstick clean.

3. Reinsert dipstick into transmission fill hole. Bottom edge of threaded section of dipstick
should rest on lip of fill hole. Do not screw filler plug in.

4. See Transmission Filler Plug/Dipstick. Remove filler plug and check lubricant level on
dipstick. If necessary, add GENUINE HarleyDavidson FORMULA+ TRANSMISSION AND
PRIMARY CHAINCASE LUBRICANT (Part No. 9985105 quart) and recheck until level is
between lower mark (1) and upper mark (2) on dipstick.
NOTE:

Do not overfill or leakage may occur. The transmission capacity is approximately 32 oz. 0.95
liters .

5. Inspect Oring on drain plug for tears or damage. Replace as required. Wipe any foreign
material from plug.

6. Install filler plug/dipstick and tighten to 2575 inlbs (2.88.5 Nm).

Changing Transmission Lubricant

1. See Transmission Filler Plug/Dipstick Location. Remove transmission filler plug.

When draining or adding lubricant, do not allow dirt, debris
or other contaminants to enter the engine. (00198a)

2. See Oil Pan. Remove transmission drain plug and drain lubricant into a suitable container.
NOTE:

Dispose of transmission lubricant in accordance with local regulations.

3. Inspect oring on drain plug for tears or damage. Replace as required. Wipe any foreign
material from plug.

Do not overtighten filler or drain plug. Doing so could
result in a lubricant leak. (00200b)

4. Install oring and drain plug. Tighten to 1421 ftlbs (19.028.5 Nm). Do not overtighten.

5. Fill the transmission with 32 oz. 0.95 liter of GENUINE HarleyDavidson FORMULA+
TRANSMISSION AND PRIMARY CHAINCASE LUBRICANT (Part No. 9985105) (quart).

6. With motorcycle on a level surface and resting on jiffy stand, check lubricant level.

a. Insert filler plug/dipstick into transmission fill hole but do not thread in.

b. See Transmission Filler Plug/Dipstick. Remove filler plug/dipstick and check
lubricant level on dipstick. Lubricant level should be between upper mark (2) and lower
mark (1). If necessary, add lubricant until level is correct.

7. Install filler plug/dipstick and tighten to 2575 inlbs (2.88.5 Nm).

Transmission Filler Plug/Dipstick Location
1. Lower mark (add lubricant)
2. Upper mark (full)
3. Bottom edge of threaded section
4. Oring
Transmission Filler Plug/Dipstick

1. Engine oil drain plug and oring
2. Transmission drain plug
Oil Pan

Primary Chaincase Lubrication

Lubrication is a major factor in the performance and service life of the clutch components.
Refer to Regular Service Intervals: 2009 Dyna Models. The primary chaincase should be
drained and refilled with fresh lubricant at proper intervals.
NOTE:

Use only GENUINE HarleyDavidson FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE
LUBRICANT (Part No. 9985105 quart) when changing primary chaincase lubricant.

Changing Primary Chaincase Lubricant

1. Run motorcycle until engine is warmed up to normal operating temperature.

When draining or adding lubricant, do not allow dirt, debris
or other contaminants to enter the engine. (00198a)

2. See Removing Chaincase Drain Plug. Remove magnetic drain plug at bottom of primary
chaincase. Drain lubricant into suitable container.
NOTE:

Dispose of lubricant in accordance with local regulations.

3. Clean drain plug. If plug has accumulated a lot of debris, inspect the condition of chaincase
components.

4. Install new oring on drain plug.

5. Install drain plug back into primary chaincase cover. Tighten plug to 1421 ftlbs (19.028.5
Nm).

6. See Clutch Cover. Remove five TORX screws with captive washers (3) to detach clutch
inspection cover (2) from primary chaincase cover.

7. Remove the seal (1). Wipe oil from groove in chaincase cover and mounting surface.

Do not overfill the primary chaincase with lubricant.
Overfilling can cause rough clutch engagement,
incomplete disengagement, clutch drag and/or difficulty in
finding neutral at engine idle. (00199b)

8. Refer to Primary Chaincase Lubricant Refill Capacity. Pour the specified amount of
GENUINE HarleyDavidson FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE
LUBRICANT (Part No. 9985105 quart) in through the clutch inspection cover opening.

Primary Chaincase Lubricant Refill Capacity

ITEM CAPACITY
Primary chaincase lubricant 32 oz 0.95 L wet
40 oz 1.18 L dry

Removing Chaincase Drain Plug
1. Seal
2. Clutch inspection cover
3. Screws with captive washer
Clutch Cover

9. Install clutch inspection cover and new seal as follows:

a. Thoroughly wipe all lubricant from cover mounting surface and groove in chaincase.

b. See Clutch Cover. Position new seal (1) in groove in primary chaincase cover and
press each of the nubs on seal into the groove. The nubs will retain seal in position.

c. See Clutch Cover Torque Sequence. Insert screw (with captive washer) through
clutch inspection cover and carefully thread it into the top cover screw hole.

d. Start the remaining four screws (with captive washers).

e. Alternately tighten screws to 84108 inlbs (9.512.2 Nm) following torque sequence
shown in Clutch Cover Torque Sequence.
Clutch Cover Torque Sequence

Rear Drive Belt: Dyna Models

General

The inner tooth surface of the secondary belt has a thin coating of polyethylene lubricant. During
initial operation, this coating will wear off as it is burnished into the belt fabric. This is a normal
condition and not an indication of belt wear.

Refer to Regular Service Intervals: 2009 Dyna Models. Belt tension is set at the factory and
should be checked after the first 1000 miles 1600 kilometers and at proper intervals thereafter.

Checking Deflection

See Belt Deflection: Dyna Models. Check belt deflection at the loosest spot in the belt with the
transmission in neutral and the motorcycle at ambient temperature. With motorcycle on sidestand
without rider or luggage, use the BELT TENSION GAUGE HD35381 to apply 10 lbs. 4.5 kg of
force at the midpoint of the bottom belt strand.

Belt deflection should be within specification as shown in Belt Deflection: 2009 Dyna Models.
If belt tension adjustment is necessary, see a HarleyDavidson dealer or follow the instructions
given in the applicable Service Manual.

Be sure wheel and brake caliper are aligned. Riding with a
misaligned wheel or brake caliper can cause the brake disc
to bind and lead to loss of control, which could result in
death or serious injury. (00050a)

Check rear brake caliper position on rear brake disc. Disc should run true within brake caliper.

1. Transmission sprocket
2. Rear wheel sprocket
3. Force of 10 lbs (4.5 kg)
4. Belt deflection
Belt Deflection: Dyna Models

Belt Deflection: 2009 Dyna Models

MODELS INCHES MILLIMETERS

FXD, FXDC, FXDF 5/163/8 7.99.5
FXDB, FXDL 1/45/16 6.47.9

Chassis Lubrication

Refer to Regular Service Intervals: 2009 Dyna Models for all maintenance schedules.

Do not switch lubricant brands indiscriminately because
some lubricants interact chemically when mixed. Use of
inferior lubricants can damage the engine. (00184a)

1. Use recommended special purpose grease for steering head bearings. Use a multipurpose
chassis grease for other applications.

2. Remove and lubricate handlebar throttle control grip sleeve with fresh graphite at proper
intervals.
3. Lubricate throttle control cables and clutch control cable at proper intervals.

4. Lubricate front brake hand lever and clutch control hand lever only if necessary.

5. Inspect rear fork pivot shaft bearings.

6. Pack the steering head bearings with fresh grease at proper intervals.

7. Lubricate the jiffy stand mechanism with LOCTITE AEROSOL ANTISEIZE at proper
intervals.
NOTE:

For model specific information regarding the chassis lubrication, refer to the appropriate Service
Manual or see a HarleyDavidson dealer.

Oil Applications

Refer to Regular Service Intervals: 2009 Dyna Models for all control connections and parts.
Vehicle should be oiled at regular intervals, particularly after washing motorcycle or driving in wet
weather.

Front Fork Oil: Dyna Models

Refer to Regular Service Intervals: 2009 Dyna Models. At the scheduled service interval,
see a HarleyDavidson dealer for fork oil replacement. If the fork does not appear to be working
properly or an appreciable amount of oil leakage should develop, see a HarleyDavidson dealer. If
there is insufficient oil in either side of fork, the rebound action will be incorrect.

Fuel Filter

Fuel injected motorcycles have a fuel filter attached to the fuel pump.
NOTE:

For model specific information regarding fuel filter maintenance, refer to the appropriate Service
Manual or see a HarleyDavidson dealer.

Clutch

The clutch control cable must be oiled and adjusted
periodically to compensate for lining wear. See Service
Interval Table. Failure to oil and adjust the clutch control
cable can result in equipment damage. (00203a)

The need for attention to clutch and controls will be indicated by the clutch slipping under load or
dragging when released. In this situation, check the control cable adjustment first. See a Harley
Davidson dealer for proper service.

Hydraulic Lifters
The hydraulic lifters are selfadjusting. They automatically adjust length to compensate for engine
expansion and valve mechanism wear. This keeps the valve mechanism free of lash when the
engine is running.

When starting an engine which has been turned off even for a few minutes, the valve mechanism
may be slightly noisy until the hydraulic units completely refill with oil. If at any time the valve
mechanism becomes abnormally noisy, other than for a short period immediately after engine is
started, it is an indication that one or more of the hydraulic units may not be functioning properly.

Always check the oil supply in the oil tank first since normal circulation of oil through the engine is
necessary for proper operation of the hydraulic units.

If there is oil in the tank, the units may not be functioning properly because of dirt in the oil supply
passages leading to the lifter units. See a HarleyDavidson dealer for service.

Front Fork Bearings

Adjustments to front fork bearings should be performed by
a HarleyDavidson dealer. Improperly adjusted bearings
can adversely affect handling and stability, which could
result in death or serious injury. (00051a)

Refer to Regular Service Intervals: 2009 Dyna Models. Check front fork for proper bearing
adjustment and lubricate bearings at proper intervals.

With motorcycle front end raised off the floor, be sure front fork turns freely without any binding or
interference and that there is no appreciable front to rear fork shake indicating excessive bearing
looseness. Steering head bearings should be adjusted according to Service Manual procedure, if
necessary.

Rear Fork Pivot Shaft

Refer to Regular Service Intervals: 2009 Dyna Models. Check the tightness of the rear fork
pivot shaft fastener at proper intervals.
NOTE:

For model specific information regarding the rear fork pivot shaft, refer to the appropriate Service
Manual or see a HarleyDavidson dealer.

Brakes

Inspect brake pads for wear at service maintenance
intervals. If you ride under adverse conditions (steep hills,
heavy traffic, etc.), inspect more frequently. Excessively
worn brake pads can lead to brake failure, which could
result in death or serious injury. (00052a)
1. Refer to Regular Service Intervals: 2009 Dyna Models. Check brake pads and brake
discs for wear at proper intervals.

2. Check the fluid level in the master cylinder reservoirs at proper intervals.

3. If level is low, clean dirt and debris from reservoir cover before removing.

D.O.T. 4 brake fluid will damage painted and body panel
surfaces it comes in contact with. Always use caution and
protect surfaces from spills whenever brake work is
performed. Failure to comply can result in cosmetic
damage. (00239b)

Direct contact of D.O.T. 4 brake fluid with eyes can cause
irritation. Avoid eye contact. In case of eye contact flush
with large amounts of water and get medical attention.
Swallowing large amounts of D.O.T. 4 brake fluid can
cause digestive discomfort. If swallowed, obtain medical
attention. Use in well ventilated area. KEEP OUT OF
REACH OF CHILDREN. (00240a)

4. Add D.O.T. 4 HYDRAULIC BRAKE FLUID (Part No. 9995399A) if necessary.
NOTE:

Use only D.O.T. 4 HYDRAULIC BRAKE FLUID (Part No. 9995399A) approved for brake system
use and available from your HarleyDavidson dealer.

HarleyDavidson has provided your new motorcycle with the optimum brake pad friction material
available. It is selected to give the best performance possible under dry, wet and high operating
temperature conditions. It exceeds all regulatory requirements currently in effect. However, during
some braking conditions you may experience noise. This is normal for this friction material.

Brakes are a critical safety component. Contact a Harley
Davidson dealer for brake repair or replacement.
Improperly serviced brakes can adversely affect brake
performance, which could result in death or serious injury.
(00054a)

See Brake Friction Material. Visual inspection of brake pads can be made without removing the
caliper. View the lower area of each caliper with a flashlight.

Perform routine scheduled brake maintenance. Lack of
maintenance at recommended intervals can adversely
affect brake performance, which could result in death or
serious injury. (00055a)

Always replace brake pads in complete sets for correct
and safe brake operation. Improper brake operation could
result in death or serious injury. (00111a)
NOTES:

If the brake pad friction material is 0.04 in. 1.02 mm thick or less, the pads must be replaced
immediately.
Always replace brake pads in pairs.

The rear brake outer pad on all models can be measured from the caliper bracket side using a
thin plastic 6.0 in. 152.4 mm rule. Place the rule against the brake disc through the space
alongside the caliper.

The outer surface of the brake pad backing plate should measure 0.04 in. 1.02 mm or more away
from the brake disc.
NOTE:

Replace pads if brake friction material is 0.04 in. 1.02 mm or less above the backing plate.

1. Front brake bottom view
2. Rear brake top view
Brake Friction Material

Tires
See Specifications: 2009 Dyna Models for tire pressures and sizes.

Be sure to keep tires properly inflated.
Follow tire data for correct cold tire inflation pressures.
Check before riding when tires are cold.
Do not overinflate tires.

Do not inflate tire beyond maximum pressure as specified
on sidewall. Over inflated tires can blow out, which could
result in death or serious injury. (00027a)

Check inflation pressure and inspect tread for punctures, cuts, breaks, etc., at least weekly if in
daily use. Check before each trip if used occasionally.

Same as original equipment tires should be used. Other tires may not fit correctly, could adversely
affect handling, and may be hazardous to use.

Tires are a critical safety component. Contact a Harley
Davidson dealer for tire repair or replacement. Improper
tire service can adversely affect stability and handling,
which could result in death or serious injury. (00057a)

Striking an object, such as a curb, can cause internal tire
damage. If an object is struck, remove and inspect both
the inside and outside of the tire. A damaged tire can
adversely affect stability and handling, which could result
in death or serious injury. (00058a)

Tire Replacement

Inspection

See Tire Sidewall Wear Bar Locator. Arrows on tire sidewalls pinpoint location of wear bar
indicators.

Tread wear indicator bars will appear on tire tread surfaces when 1/32 in. 0.8 mm or less of tire
tread remains. See Wear Bar Appearance (Typical). Always replace tires before the tread
wear indicator bars appear.

When To Replace Tires

New tires are needed if any of the following conditions exist:

1. Tread wear indicator bars become visible on the tread surfaces.

2. Tire cords or fabric become visible through cracked sidewalls, snags or deep cuts.

3. A bump, bulge or split in the tire.

4. Puncture, cut or other damage to the tire that cannot be repaired.
Tire Sidewall Wear Bar Locator

Wear Bar Appearance (Typical)
Vehicle Alignment

Isolation Mounted Engine Models

Refer to Regular Service Intervals: 2009 Dyna Models. Vehicle alignment should be
checked at regular intervals. This includes whenever the rear wheel is removed and installed or
when the rear drive belt is adjusted. The stabilizer links and engine mounts should be checked for
wear according to Service Manual procedures at proper intervals.

Vehicle alignment is important. Vehicle stability is adversely affected if wheels are out of
alignment. Major alignment of the front and rear wheel is partially controlled by one stabilizer link
at the top of the engine. See a HarleyDavidson dealer for this service.

Do not change stabilizer link adjustment. Changing
adjustment can adversely affect stability, which could
result in death or serious injury. (00059a)

Only a HarleyDavidson dealer should perform vehicle
alignment. Improper alignment can adversely affect
stability and handling, which could result in death or
serious injury. (00060a)

Shock Absorbers

Refer to Regular Service Intervals: 2009 Dyna Models. Inspect shock absorbers and rubber
bushings for leaks and bushing deterioration at proper intervals.

Spark Plugs

Refer to Regular Service Intervals: 2009 Dyna Models. Check the spark plugs at proper
intervals.

Do NOT pull on any electrical wires. Pulling on electrical
wires may damage the internal conductor causing high
resistance, which may result in minor or moderate injury.
(00168a)

Disconnect spark plug cables from plugs by pulling on the molded connector caps. To reconnect,
simply snapon spark plug cables to tops of spark plugs.

Refer to Ignition System: 2009 Twin Cam Models before servicing spark plugs.
1. Check spark plug type. Only use those spark plugs specified for your model motorcycle.

2. Check spark plug gap against table specifications.

3. Always tighten to the proper torque. Spark plugs must be tightened to the torque specified
for proper heat transfer.
NOTE:

If a torque wrench is not available, tighten plugs finger tight and then tighten an additional one
quarter turn with a spark plug wrench.

Ignition

The engine in your motorcycle has been designed specifically to achieve optimum fuel economy
within exhaust emission controls. Factory programmed ignition characteristics provide maximum
engine performance and driveability.

Air Cleaner

See Air Cleaner Assembly: Dyna Models. The engine air cleaner is a paper/wire mesh air
filter element.

Refer to Regular Service Intervals: 2009 Dyna Models. Remove air cleaner cover and
inspect filter element at proper intervals. Under dusty conditions, inspect more often.

The paper/wire mesh air filter element should be washed in luke warm water with a mild
detergent.

Install baseplate gasket, air filter element, and bracket if removed. Tighten bracket screws to 40
60 inlbs (4.56.8 Nm).

When installing air cleaner cover, apply a drop of LOCTITE THREADLOCKER 243 (blue) to the
threads of the cover screw and tighten to 3660 inlbs (4.16.8 Nm).

Compressed air can pierce the skin and flying debris from
compressed air could cause serious eye injury. Wear
safety glasses when working with compressed air. Never
use your hand to check for air leaks or to determine air
flow rates. (00061a)

Allow filter to either air dry or blow it dry, from the inside, with low pressure air.
Do not use an air cleaner filter oil on the HarleyDavidson paper/wire mesh air filter element.

Install air filter before running engine. Failure to do so can
draw debris into the engine and could result in engine
damage. (00207a)
1. Cover screw
2. Air cleaner cover
3. Filter/bracket screws (3)
4. Filter element
5. Backplate
Air Cleaner Assembly: Dyna Models

Headlamp

See Headlamp Bulbs: Dyna Models. The headlamp assembly uses replaceable quartz
halogen bulb(s).

Refer to Bulb Chart: 2009 Dyna Models for bulbs. See a HarleyDavidson dealer or service
manual for bulb replacement.

When replacement is required, use only the specified
sealed beam unit or bulb, available from a HarleyDavidson
dealer. An improper wattage sealed beam or bulb, can
cause charging system problems. (00209a)

Never touch the quartz bulb. Fingerprints will etch the
glass and decrease bulb life. Grab the bulb with paper or a
clean, dry cloth. Failure to do so could result in bulb
damage. (00210a)

Handle bulb carefully and wear eye protection. Bulb
contains gas under pressure, which, if not handled
carefully, could cause serious eye injury. (00062b)
1. Headlamp assembly (Dyna models except FXDF)
2. Headlamp assembly (FXDF model)
3. Headlamp bulb(s)
4. Position lamp bulb (international models only)
Headlamp Bulbs: Dyna Models

Headlamp Alignment

NOTE:

Vehicles with multiple beam headlamps that are individually aimed should be adjusted so both
lamps converge into one pattern.

1. Verify that front and rear tire inflation pressures are correct and that suspension is adjusted
to the weight of the principal rider. See Specifications.

2. Fill fuel tank or add ballast to equal the weight of the fuel needed.
NOTE:

See Checking Headlamp Alignment. To aid in properly placing the motorcycle, a
perpendicular line (1) can be drawn on the floor. For best results, choose an area with
minimum light.

3. See Checking Headlamp Alignment. Draw a vertical line (2) on the wall.

4. Position motorcycle so that front axle is 25 feet 7.6 meters from wall.
NOTE:

As the weight of the rider will compress the suspension slightly, have a person whose
weight is approximately the same as that of the principal rider sit on the motorcycle.

5. With the vehicle laden and upright, point the front wheel straight forward at wall and
measure the distance (4) from the floor to the center of the HIGH BEAM bulb.

6. Draw a horizontal line (5) through the vertical line on the wall that is 2.1 in. 53.3 mm lower
than the measured bulb centerline.
1. Perpendicular line
2. Vertical line
3. 25 feet (7.6 meters)
4. High beam bulb centerline
5. Horizontal line 2.1 in. (53.3 mm) lower than bulb centerline
Checking Headlamp Alignment

NOTE:

As the weight of the rider will compress the suspension slightly, have a person whose weight is
approximately the same as that of the principal rider sit on the motorcycle.

7. See Checking Headlamp Alignment. Verify headlamp alignment. Turn the ignition switch
to IGNITION and set the headlamp switch to HIGH beam.

a. The center of the hot spot (brightest area of light beam) should be centered where the
two lines intersect.

b. Adjust headlamp alignment if necessary.

Headlamp Adjustment

1. See Headlamp Adjustment: FXDF Models (FXDF) or Headlamp Adjustment (other
models). Loosen horizontal adjusting bolt (2) to adjust headlamp beam side to side. Tighten
bolt to 2530 ftlbs (33.940.7 Nm).

2. Loosen nut on vertical adjusting bolt (1) to adjust headlamp beam up or down. Tighten bolt
to 2530 ftlbs (33.940.7 Nm).
1. Vertical adjusting bolt
2. Horizontal adjusting bolt
Headlamp Adjustment: FXDF Models

1. Vertical adjusting bolt
2. Horizontal adjusting bolt
Headlamp Adjustment

Turn Signal Bulb Replacement: Bullet Style
1. See Lens Cap Notch. Insert a coin or the blade of a small screwdriver into the notch at the
bottom of the lens cap. Carefully twist until the lens cap pops out of the lamp housing.

2. Push in bulb and rotate counterclockwise. Pull bulb from socket.

3. Inspect condition of electrical contacts in socket. If necessary, clean with a small wire brush
and electrical contact cleaner.

4. Coat base of new bulb with ELECTRICAL CONTACT GREASE 9986190 .

5. Orient index pins on new bulb with pin guides inside bulb socket. Push bulb in and turn
clockwise to lock in place.

6. Snap lens cap back into the lamp holder. Rotate lens to position notch at bottom of lamp.

Be sure that all lights and switches operate properly
before operating motorcycle. Low visibility of rider can
result in death or serious injury. (00316a)

7. Turn ignition on and test for proper turn signal operation.
NOTE:

If the turn signal or running lamp will not light after replacing a bulb, check the wiring, the ground
at the socket and/or the switch.

Lens Cap Notch

Tail Lamp: FXDB Model
The FXDB tail lamp is an LED assembly with no replaceable bulbs. The cover on the tail lamp is
not removable. See a dealer or service manual for assembly replacement.

Tail Lamp Bulb Replacement: Standard Style

1. See Tail Lamp Assembly: Standard Style. Make certain ignition switch is turned off.

2. Remove two screws and lens from base.
NOTE:

For ease of bulb removal, the 4Pin multilock connector can be removed from circuit board.

3. Remove (pull) bulb assembly from lens. Remove bulb from socket.

4. Coat base of new bulb with ELECTRICAL CONTACT GREASE (Part No. 9986190). Install
new bulb in socket.

5. Install (push) bulb assembly to lens.

6. If removed connect 4Pin multilock connector to circuit board.

7. Install lens to base with two screws. Tighten screws to 2024 inlbs (2.32.7 Nm).

Be sure that all lights and switches operate properly
before operating motorcycle. Low visibility of rider can
result in death or serious injury. (00316a)

8. Turn ignition on and test for proper tail lamp operation.
1. Lens
2. Base
3. 4pin multilock connector
4. Bulb assembly
Tail Lamp Assembly: Standard Style

Alternator/Voltage Regulator

Charging Rate

The alternator output is controlled and changed to direct current by the voltage regulator.

The voltage regulator increases charging rate when battery is low or lamps are lit.
The voltage regulator decreases charging rate when battery charge is up.

It is possible to overload your motorcycle's charging
system by adding too many electrical accessories. If your
combined electrical accessories operating at any one time
consume more electrical current than your vehicle's
charging system can produce, the electrical consumption
can discharge the battery and cause vehicle electrical
system damage. See a HarleyDavidson dealer for advice
about the amount of current consumed by additional
electrical accessories, or for necessary wiring changes.
(00211b)

A battery voltage LED in the instruments will light up when voltage is either too low or too high.
NOTES:

This unit requires no interval attention. If any electrical system trouble is experienced that
might be traceable to the alternator or voltage regulator, the motorcycle should be taken to a
HarleyDavidson dealer who has the necessary electrical testing equipment to give the
required attention.
For model specific information regarding the voltage regulator, refer to the appropriate
Service Manual or see a HarleyDavidson dealer.

Battery: General

Type

Your motorcycle uses a permanently sealed, maintenancefree, lead/calcium and sulfuric acid
battery. All batteries are shipped precharged and ready to be put into service. Do not attempt to
open the battery for any reason.

Antidotes for Battery Acid

CONTACT TREATMENT
External Flush with water.
Internal Drink large quantities of milk or water,
followed by milk of magnesia, vegetable oil
or beaten eggs. Get immediate medical
attention.
Eyes Flush with water. Get immediate medical
attention.

Batteries contain sulfuric acid, which could cause severe
burns to eyes and skin. Wear a protective face shield,
rubberized gloves and protective clothing when working
with batteries. KEEP BATTERIES AWAY FROM CHILDREN.
(00063a)

Explosive hydrogen gas, which escapes during charging,
could cause death or serious injury. Charge battery in a
wellventilated area. Keep open flames, electrical sparks
and smoking materials away from battery at all times.
KEEP BATTERIES AWAY FROM CHILDREN. (00065a)

Batteries, battery posts, terminals and related accessories
contain lead and lead compounds, and other chemicals
known to the State of California to cause cancer, and birth
defects or other reproductive harm. Wash hands after
handling. (00019e)
Never remove warning label attached to top of battery.
Failure to read and understand all precautions contained
in warning, could result in death or serious injury. (00064a)

1. Contents are corrosive
2. Wear safety glasses
3. Contents are explosive
4. Keep flames away
5. Read instructions
6. Keep away from children
Battery Warning Label

Battery Warning Label
Voltmeter Test

Refer to Voltmeter Test. The voltmeter test provides a general indicator of battery condition.
Check the voltage of the battery to verify that it is in a 100 percent fully charged condition. If the
open circuit (disconnected) voltage reading is below 12.6V, charge the battery and then recheck
the voltage after the battery has set for one to two hours.

Voltmeter Test

READING IN VOLTS PERCENT OF CHARGE
12.7 100
12.6 75
12.3 50
12.0 25
11.8 0

Cleaning and Inspection

Battery top must be clean and dry. Dirt and electrolyte on top of the battery can cause battery to
selfdischarge.

1. Clean battery top.

2. Clean cable connectors and battery terminals using a wire brush or fine grit sandpaper to
remove any oxidation.

3. Inspect and clean the battery screws, clamps and cables. Check for breakage, loose
connections and corrosion.

4. Check the battery posts for melting or damage caused by overtightening.

5. Inspect the battery for discoloration, a raised top or a warped or distorted case. This might
indicate that the battery has been frozen, overheated or overcharged.

6. Inspect the battery case for cracks or leaks.

Charging

Never charge a battery without first reviewing the instructions for the charger being used. In
addition to the manufacturer's instructions, follow these general safety precautions.

Charge the battery if any of the following conditions exist:

Vehicle lamps appear dim.
Electric starter sounds weak.
Battery has not been used for an extended period of time.
Explosive hydrogen gas, which escapes during charging,
could cause death or serious injury. Charge battery in a
wellventilated area. Keep open flames, electrical sparks
and smoking materials away from battery at all times.
KEEP BATTERIES AWAY FROM CHILDREN. (00065a)

1. Perform a voltmeter test to determine the state of charge. If battery needs to be charged,
proceed to the next step.

2. Place the battery on a level surface.

Unplug or turn OFF battery charger before connecting
charger cables to battery. Connecting cables with charger
ON can cause a spark and battery explosion, which could
result in death or serious injury. (00066a)

Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative () cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)

Disconnect negative () battery cable first. If positive (+)
cable should contact ground with negative () cable
connected, the resulting sparks can cause a battery
explosion, which could result in death or serious injury.
(00049a)

Do not reverse the charger connections described in the
following steps or the charging system of the motorcycle
could be damaged. (00214a)

NOTES:
The figures listed in the Amphour table assume that the battery is charging at room
temperature. If warmer than room temperature, use a slightly shorter charging time. If
colder, use a slightly longer charging time.
The use of constant current chargers to charge sealed maintenance free batteries is
not recommended. Any overcharge will cause dryout and premature battery failure. If
a constant current charger is the only type available, do not exceed the charge times
listed in 19 Amp Hour Battery Charging Rates/Times and do not continue
charging the battery if it gets hot. When charging, never exceed 15 volts.

3. Connect the red battery charger lead to positive (+) terminal of the battery.

4. Connect the black battery charger lead to negative () terminal of the battery.
NOTE:

If the battery is still in the vehicle, connect the negative lead to the chassis ground. Make
sure that the ignition and all electrical accessories are turned off.

5. Step away from the battery and turn on the charger.

Unplug or turn OFF battery charger before disconnecting
charger cables from battery. Disconnecting clamps with
charger ON can cause a spark and battery explosion,
which could result in death or serious injury. (00067a)

6. After the battery is fully charged, turn OFF the charger and disconnect the black battery
charger lead to the negative () terminal of the battery.

7. Disconnect the red battery charger lead to the positive (+) terminal of the battery.

8. Mark the charging date on the battery.

19 Amp Hour Battery Charging Rates/Times

READING PERCENT 3 AMP 6 AMP 10 AMP 20 AMP

(VOLTS) OF CHARGE CHARGER CHARGER CHARGER CHARGER

12.7 100
12.6 75 1 hour 55 minutes 30 minutes 15 minutes

50 minutes
12.3 50 3 hours 1 hour 1 hour 30 minutes

40 minutes 50 minutes 5 minutes

12.0 25 5 hours 2 hours 1 hours 45 minutes

15 minutes 40 minutes 35 minutes

11.8 0 7 hours 3 hours 2 hours 1 hour

30 minutes 5 minutes 5 minutes

Storage

Turn engine over a few times to be sure there is no oil in
the crankcase and that all oil has been pumped back into
the oil tank. Stop engine and recheck oil level. Failure to
do so can result in engine damage. (00071a)

Do not allow battery to completely discharge. The
electrolyte in a discharged battery will freeze. The more
discharged a battery is, the more easily it can freeze and
crack the battery case. (00218a)

If the motorcycle will not be operated for several months, such as during the winter season,
remove the battery from the motorcycle and fully charge.

If the motorcycle is to be stored with the battery installed, it will be necessary to connect a battery
tender to maintain charge. See an authorized dealer for more information.

Selfdischarge is a normal condition and occurs continuously. The rate of selfdischarge depends
on the ambient temperature and the battery's state of charge.

Batteries discharge at a faster rate at higher ambient temperatures.
To reduce the selfdischarge rate, store battery in a cool (not freezing), dry place.
Charge the battery every month if stored at temperatures below 60° F 16° C .
Charge the battery more frequently if stored in a warm area above 60° F 16° C .
1. Capacity
2. Months of nonuse
3. Measured at 105° F (40° C)
4. Measured at 77° F (25° C)
Effective Rate of Temperature on Battery
Selfdischarging Rate

Battery: Dyna Models

Disconnection and Removal

Before you can inspect or disconnect your battery you must read the section containing
information about seat removal.

1. See Battery Compartment: Dyna Models. Remove the fastener under the battery cover
on the right side of the motorcycle.

2. Remove battery cover.

3. Remove the negative () cable (black) from battery negative () terminal.

4. Remove battery positive cable (red) from battery positive (+) terminal.
5. Remove the rubber hold down strap and slide the battery out of the battery compartment.

Installation and Connection

Connect the cables to the correct battery terminals. Failure
to do so could result in damage to the motorcycle
electrical system. (00215a)

Do not allow positive (+) battery cable to contact ground
with negative () cable connected. Resulting sparks can
cause a battery explosion, which could result in death or
serious injury. (00069a)

1. Place the fully charged battery into the battery compartment.

Do not overtighten bolts on battery terminals. Use
recommended torque values. Overtightening battery
terminal bolts could result in damage to battery terminals.
(00216a)

2. Insert bolt through battery positive cable (+) (red) into threaded hole of battery positive (+)
terminal.

3. Tighten bolt to 6070 inlbs (6.87.9 Nm).

4. Insert bolt through battery negative cable () (black) into threaded hole of battery negative ()
terminal.

5. Tighten bolt to 6070 inlbs (6.87.9 Nm).

Keep battery clean and lightly coat terminals with
petroleum jelly to prevent corrosion. Failure to do so could
result in damage to battery terminals. (00217a)
6. Apply a light coat of petroleum jelly or corrosion retardant material to both battery terminals.

7. Install battery side cover.

8. Install lower fastener. Tighten to 2040 inlbs (2.264.52 Nm).

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

1. Battery compartment cover
2. Cover fastener
Battery Compartment: Dyna Models

Jump Starting

HarleyDavidson does not recommend jumpstarting a motorcycle. However, there may be
circumstances when it is necessary to do so. Therefore, we suggest jumpstarting be performed
as follows:

Be sure jumper cables touch only appropriate battery
terminals or ground. Allowing jumper cables to touch each
other can result in sparks and a battery explosion, which
could result in death or serious injury. (00072a)

Explosive hydrogen gas, which escapes during charging,
Explosive hydrogen gas, which escapes during charging,
could cause death or serious injury. Charge battery in a
wellventilated area. Keep open flames, electrical sparks
and smoking materials away from battery at all times.
KEEP BATTERIES AWAY FROM CHILDREN. (00065a)

HarleyDavidson motorcycles have a 12 Volt battery. Be
sure the booster vehicle has a 12 Volt system. Failure to
do so could result in vehicle damage. (00220a)

NOTE:

This procedure presumes the BOOSTER battery is in another vehicle.

1. Turn off all unnecessary lamps and accessories.

Positive Cable

2. See Jump Start Cable Connections. Connect one end of a jumper cable to the
DISCHARGED battery positive (+) terminal (1).

3. Connect the other end of the same cable to the BOOSTER battery positive (+) terminal (2).

Negative Cable

Do not connect negative () cable to or near the discharged
battery negative () terminal. Doing so could cause a spark
and explosion, which could result in death or serious
injury. (00073a)

4. Connect one end of a jumper cable to the BOOSTER battery negative () terminal (3).

Do not connect the negative () cable to painted or chrome
parts. Doing so could result in discoloration at the
attachment point. (00221a)

5. Connect other end of the same cable (4) to a safe ground, (away from the DISCHARGED
battery).

6. Start motorcycle.

7. Disconnect cables in reverse order of steps 2, 3, 4, 5. That is: steps 5, 4, 3, 2.
1. Discharged battery positive (+) terminal
2. Booster battery positive (+) terminal
3. Booster battery negative () terminal
4. Ground
Jump Start Cable Connections

Electrical Protection: Dyna Models

Fuses

See Fuse Block: 2009 Dyna Models. The fuse block is under the motorcycle's left side cover,
behind the electrical panel cover. The block contains replaceable fuses.
NOTE:

See Fuse Block: 2009 Dyna Models. Spare fuses are inserted into slots 7 and 8 in the fuse
block. Automotive type ATO fuses are used for replacements.

Fuse Replacement

1. Place the ignition/headlamp key switch in the OFF position.

2. Gently pull left side cover from frame. (No tools are required for this step.)

3. See Fuse Block: 2009 Dyna Models. Remove the fuse and inspect the element.
Always use replacement fuses that are of the correct type
and amperage rating. Use of incorrect fuses can result in
damage to electrical systems. (00222a)

4. Align studs in side cover with grommets in frame and firmly push the side cover into place.

1. Start relay
2. System relay
3. Main fuse (40 amp)
4. ECM module (15 amp)
5. Fuel pump (15 amp)
6. Blank (HDI: Engine Control Fuse)
7. Spare (15 amp)
8. Spare (15 amp)
9. Customer accessory (15 amp)
10. P&A ignition (2 amp max)
11. Battery (15 amp)
12. Accessories (15 amp)
13. Instruments (15 amp)
14. Ignition (15 amp)
15. Lamps (15 amp)
Fuse Block: 2009 Dyna Models

Replacing the Main Fuse

See Main Fuse. All Dyna models have a main fuse to protect the motorcycle wiring. This 40amp
main fuse provides main battery power to the motorcycle. It is located in the fuse holder behind
the motorcycle's left side cover.

1. Gently pull left side cover from frame. (No tools are required for this step.)

2. Grasp and pull the main fuse straight out of the fuse holder.

3. Insert the prongs of the new main fuse in the fuse holder slots.

4. Align studs in side cover with grommets in frame and firmly push the side cover into place.
Main Fuse

Seat: Dyna Models

Removal

1. See Seat: Dyna Models. Remove screw and detach seat mounting bracket from top of
rear fender.
NOTE:

The straps are secured to the fender under the seat by a nut and washer.

2. Raise seat and remove nut and washer from seat straps.

3. Slide seat to the rear of the motorcycle and lift seat.

4. It is not necessary to remove the seat bracket and its fasteners from the seat pan.

Installation

1. Place seat on frame backbone.
NOTE:

There is a tab at the front of the seat that slips under the rear fuel tank mount.

2. Slide seat toward front of motorcycle until the tab locks under the fuel tank mount.

3. See Seat: Dyna Models. Push seat forward until rear fender seat retention nut is centered
in hole of mounting bracket.

4. Install washer and nut to secure seat straps.
5. Install screw and bracket to fender.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

6. Pull up on seat to verify that it is properly secured.

1. Screw
2. Bracket
3. Nylon clip
4. Nut
5. Washer
Seat: Dyna Models

Motorcycle Storage

Placing Motorcycle in Storage

Proper storage is important for the troublefree operation
of your motorcycle. See your Owner's Manual for storage
recommendations or see a HarleyDavidson dealer.
Improper storage procedures can lead to equipment
damage. (00046a)

If the motorcycle will not be operated for several months, such as during the winter season, there
are several tasks which should be performed. These steps will protect parts against corrosion,
preserve the battery and prevent the buildup of gum and varnish in the fuel system.

NOTE:

Make a list of everything you do and fasten it to a handgrip. When you take the motorcycle out of
storage, this list will be your reference/checklist to get your motorcycle in operating condition.

1. Fill fuel tank and add a gasoline stabilizer. Use one of the commercially available gasoline
stabilizers and follow the manufacturer's instructions.

2. Warm motorcycle to operating temperature. Change oil and turn engine over to circulate the
new oil.

3. Check and adjust belt if necessary.

4. Check tire inflation. Adjust to proper inflation pressure.

5. To protect the vehicle's body panels, engine, chassis and wheels from corrosion, follow the
cosmetic care procedures described in the Accessory Maintenance section of this owner's
manual prior to storage.

6. Prepare battery for winter storage. See Battery: General.

7. If the motorcycle is to be stored with security system armed, it will be necessary to connect
a Battery Tender to maintain battery charge. If security system will not be armed and a
Battery Tender is not available, either:

a. Disconnect negative battery cable.

b. Remove main fuse (if applicable).

8. If motorcycle is to be covered, use a material such as light canvas that will breathe. Plastic
materials that do not breathe promote the formation of condensation.
Removing Motorcycle From Storage

The clutch failing to disengage can cause loss of control,
which could result in death or serious injury. Prior to
starting after extended periods of storage, place
transmission in gear and push vehicle back and forth
several times to assure proper clutch disengagement.
(00075a)

1. See Battery: General for proper battery care. Charge and install the battery.

2. Remove and inspect the spark plugs. Replace if necessary.

3. Clean the air cleaner element.

4. Start the engine and run until it reaches normal operating temperature. Turn off engine.

5. Check amount of oil in the oil tank.

6. Check the transmission lubricant level.

7. Check controls to be sure they are operating properly. Operate the front and rear brakes,
throttle, clutch and shifter.

8. Check steering for smoothness by turning the handlebars through the full operating range.

9. Check tire pressure. Incorrect pressure will result in poor riding characteristics and can
affect handling and stability.

10. Check all electrical equipment and switches including the stop lamp, turn signals and horn
for proper operation.

11. Check for any fuel, oil or brake fluid leaks.

General Maintenance

Maintain chrome and aluminum regularly to check that they retain their original shine and luster.
Take care to keep your new HarleyDavidson motorcycle cleaned and waxed as often as possible
to inhibit rust and corrosion.

Cleaning Your Motorcycle: Dyna Models

To aid you in keeping your motorcycle clean, see your HarleyDavidson dealer for cleaning,
polishing and waxing products.

For HarleyDavidson recommended cleaning products, refer to Recommended Cleaning Care
Products: Dyna Models.

Recommended Cleaning Care Products: Dyna Models

PRODUCT PART FRAME BODY WHEELS DENIM

NUMBER PANELS FINISH
HD Sunwash 9465998 Yes Yes Yes No
HD Bug Remover 9465798 Yes Yes Yes No
HarleyGloss 9462798 Yes Yes Yes Yes
Harley Spray Cleaner and Polish 9981799 Yes Yes Yes No
Wheel and Tire Cleaner 9465898 No No Yes No
S100 Total Cycle Cleaner 99760 Yes Yes Yes No
85T
(complete rinse required)
Grease cutting dishwasher detergent. Dilute N/A No No No Yes
per manufacturer's instructions.
Ammonia base glass cleaner N/A No No No Yes
Harley Brite Chrome Cleaner 9468399 For brushed metal surfaces.
Bright Metal Polish 9972589 For polished metal surfaces.

Observe warnings on labels of cleaning compounds.
Failure to follow warnings could result in death or serious
injury. (00076a)

Do not wash brake discs with cleaners containing chlorine
or silicone. Cleaners containing chlorine and silicone can
impair brake function, which could result in death or
serious injury. (00077a)
Do not use pressure washers to clean wheel bearings,
sprocket bearings, steering head bearings and swingarm
pivot bearings. Doing so can result in equipment damage.
(00489b)

Denim Finish

General

If your vehicle has denim (flat or matte) finish please read below.

The Denim finish has qualities which differ from high gloss finishes on all other Harley
Davidson motorcycles. Like denim fabric, Denim paint will burnish or mar with age and use,
thus adding character and personality to the finish of the motorcycle.
If scratched, the color coat of paint does nick/scuff and these marks can not be rubbed out.
If polished, the finish will become less matte and more glossy over time.

How to Clean

1. For heavier deposits:

a. Use grease cutting dishwashing detergent and a clean HD washmitt. (Dilute the
detergent per the instruction provided by its manufacturer.)

b. Rinse thoroughly with clean water.

2. For light deposits, use glass cleaner (ammonia base) and HD Soft Cloth. This helps remove
finger prints and light soil.

3. For final detailing use HD Gloss with HD Soft Cloth.

Leather Care

NOTE:

Many HarleyDavidson accessories and seats are either made of leather or have leather inserts.
Natural materials age differently and require different care than manmade materials. Seat covers
and panels made of leather will gain "character", such as wrinkles, with age. Leather is porous
and organic and each leather product will settle into its own distinct form with use. Your leather
product will mature into its own custom shape and style from the sun, rain and the miles. This
maturing is natural and will enhance the custom quality of your HarleyDavidson motorcycle.

Leather must be periodically cleaned and treated to maintain its appearance and extend its life.
Clean and treat leather once a season or more frequently under adverse conditions.

Do not use bleach or detergents containing bleach on
saddlebags, seats, tank panels or painted surfaces. Doing
so can result in equipment damage. (00229a)

Do not use ordinary soap to clean leather or fur. It could dry or remove the oils from the
leather.
Use ONLY a good quality saddle soap to clean leather. Be sure you rinse saddle soap off
thoroughly before treating leather.
Never try to dry leather quickly, using artificial means. Always let leather dry naturally, at
room temperature.

1. Vacuum or blow dust off.

2. Thoroughly clean leather with a good quality saddle soap, following manufacturer's
directions. Rinse thoroughly with clean sponge or cloth and water. Allow leather to dry.

3. Once leather is dry, treat with a good quality leather treatment, such as LEATHERCARE
(Part No. 9826191).

4. Always allow leather to dry completely before using.

Whitewall Tires

Use a good quality, commercial whitewall cleaner and follow the manufacturer's directions.

Wheel Care

Some vehicle's wheels are aluminum and do not have a protective coating. Other vehicles have
laced wheels with chrome plated rims and zinc or chrome plated spokes. Damage from harsh
chemicals, acid based wheel cleaners, brake dust and lack of maintenance can occur. Regular
washing and the use of a corrosion protectant will help to maintain their original appearance.
HarleyDavidson WHEEL AND TIRE CLEANER (Part No. 9465898) is recommended for
cleaning wheels and tires. Then use HARLEY GLOSS (Part No. 9462798) to protect the wheel
surfaces.
NOTES:

It is imperative that the wheels are cared for weekly to guard against pitting and corrosion.
Corrosion of these components is not considered to be a defect in materials or
workmanship.

HarleyDavidson recommends the following products:

WHEEL AND TIRE CLEANER (Part No. 9465898): cleaner/degreaser for wheels, tires and
engine.
HARLEY GLOSS (Part No. 9462798): all purpose surface protection the provides UV
protection and a gloss finish.

See a HarleyDavidson dealer for cleaning, polishing and waxing products.

Windshields

Polycarbonate windscreens/windshields require proper
attention and care to maintain. Failure to maintain
polycarbonate properly can result in damage to the
windscreen/windshield. (00483d)

Do not clean in hot sun or high temperature.
Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield.

Do not use harsh chemicals including rain sheeting
products on HarleyDavidson windshields. They can cause
dulling or hazing. If you want to use a windshield
protectant on your windshield, try Harley Glaze Polish and
Sealant (00231a)

Do not use benzine, paint thinner, gasoline or any other
type of harsh cleaner on the windshield. Doing so will
damage the windshield surface. (00232a)

NOTES:

To remove minor surface scratches use NOVUS® No. 2 SCRATCH REMOVER (Part No.
9983694T).
Covering the windshield with a clean, wet cloth for approximately 1520 minutes before
washing will make dried bug removal easier.

1. Use mild soap and warm water to wash the windshield.

2. Wipe dry with a soft, clean towel.
NOTE:

To treat your Lexan windshield with water repellent use WINDSHIELD WATER REPELLENT
TREATMENT (Part No. 9984102).

Troubleshooting

Troubleshooting: General

The troubleshooting section of the Owner's Manual is a
guide to diagnose problems. Read the service manual
before performing any work. Improper repair and/or
maintenance could result in death or serious injury.
(00080a)

The following checklist of possible operating troubles and their probable causes will be helpful in
keeping your motorcycle in good operating condition. More than one of these conditions may be
causing trouble and should be carefully checked.
Engine

Starter Does Not Operate or Does Not Turn Engine Over

1. Engine run switch in OFF position.

2. Ignition switch not ON.

3. Discharged battery or loose or corroded connections (solenoid chatters).

4. Clutch lever not squeezed against handlebar or transmission not in neutral.

5. Jiffy stand not in retracted position (required for international models only).

6. Blown fuse.

Engine Turns Over But Does Not Start

1. Fuel tank empty.

2. Discharged battery or loose or broken battery terminal connections.

3. Fouled spark plugs.

4. Spark plug cable connections loose or in bad condition and shorting.

5. Loose or corroded wire or cable connection(s) at coil or battery.

6. Fuel pump inoperative.

7. Blown fuse.

Starts Hard

1. Spark plugs in bad condition, have improper gap, or are partially fouled.

2. Spark plug cables in bad condition and leaking.

3. Battery nearly discharged.

4. Loose wire or cable connection(s) at one of the battery terminals or at coil.

5. Engine oil too heavy (winter operation).

6. Fuel tank vent plugged or fuel line closed off, restricting fuel flow.

7. Water or dirt in fuel system.

8. Fuel pump inoperative.

Starts But Runs Irregularly or Misses
1. Spark plugs in bad condition or partially fouled.

2. Spark plug cables in bad condition and leaking.

3. Spark plug gap too close or too wide.

4. Battery nearly discharged.

5. Damaged wire or loose connection at battery terminals or coils.

6. Intermittent short circuit due to damaged wire insulation.

7. Water or dirt in fuel system or filter.

8. Fuel vent system plugged. See dealer.

9. One or more injectors fouled.

A Spark Plug Fouls Repeatedly

1. Incorrect spark plug.

Preignition or Detonation (Knocks or Pings)

1. Incorrect fuel.

2. Incorrect spark plug for the kind of service.

Overheats

1. Insufficient oil supply or oil not circulating.

2. Heavy carbon deposit from lugging engine. See dealer.

3. Insufficient air flow over cylinder heads during extended periods of idling or parade duty.

Excessive Vibration

1. Rear fork pivot shaft nuts loose. See dealer.

2. Front engine mounting bolts loose. See dealer.

3. Engine to transmission mounting bolts loose. See dealer.

4. Broken frame. See dealer.

5. Front chain or links tight as a result of insufficient lubrication or belt badly worn.

6. Wheels and/or tires damaged. See dealer.

7. Vehicle not properly aligned. See dealer.
Electrical System

Alternator Does Not Charge

1. Module not grounded. See dealer.

2. Engine ground wire loose or broken. See dealer.

3. Loose or broken wires in charging circuit. See dealer.

Alternator Charge Rate is Below Normal

1. Weak battery.

2. Excessive use of addon accessories.

3. Loose or corroded connections.

4. Extensive periods of idling or low speed riding.

Transmission

Transmission Shifts Hard

1. Bent shifter rod. See dealer.

Transmission Jumps Out of Gear

1. Worn shifter dogs in transmission. See dealer.

Clutch Slips

1. Clutch controls improperly adjusted. See dealer.

2. Worn friction discs. See dealer.

3. Insufficient clutch spring tension. See dealer.

Clutch Drags or Does Not Release

1. Clutch controls improperly adjusted. See dealer.

2. Primary chaincase overfilled.

3. Clutch discs warped. See dealer.

Clutch Chatters
1. Friction discs or steel discs worn or warped. See dealer.

Brakes

Brakes Do Not Hold Normally

1. Master cylinder low on fluid. See dealer.

2. Brake line contains air bubbles. See dealer.

3. Master cylinder piston worn. See dealer.

4. Brake pads contaminated with grease or oil. See dealer.

5. Brake pads badly worn. See dealer.

6. Brake disc badly worn or warped. See dealer.

7. Brake fades because of heat build up. Excessive braking or brake pads dragging. See
dealer.

8. Brake drags. Insufficient hand lever free play. See dealer.

Warranties and Responsibilities

Warranty and Maintenance

This Owner's Manual contains your new motorcycle warranty.

It is the owner's responsibility to follow the scheduled mileage intervals as specified; all of the
specified maintenance services must be performed to keep your warranty valid.

1. Make an appointment with a HarleyDavidson dealer for inspection and service just before
you have ridden 1000 miles 1600 kilometers .

2. Bring this Owner's Manual with you when you visit your dealer to have your motorcycle
inspected and serviced.

3. Have the dealer technician sign at the proper mileage interval. The records should be
retained by the owner as proof of proper maintenance.

4. Keep receipts covering any parts, service or maintenance performed. These records should
be transferred to each subsequent owner.

HarleyDavidson dealerships are independently owned and operated and may sell parts and
accessories that are not manufactured or approved by HarleyDavidson. Therefore, you should
understand that we are not and cannot be responsible for the quality, suitability, or safety of any
nonHarleyDavidson part, accessory or design modification, including labor, which may be sold
and/or installed by our dealers.

Keeping It All HarleyDavidson

1. Keep your HarleyDavidson completely HarleyDavidson.

2. Insist that your dealer uses only Genuine replacement parts to keep your HarleyDavidson
motorcycle and its warranty intact.

Exacting design and stringent testing ensure performance and warranty coverage. Again, insist on
Genuine parts for your genuine HarleyDavidson motorcycle.
NOTE:

Installing offroad or competition parts to enhance performance may void all or part of your new
motorcycle warranty. See the HarleyDavidson Limited Warranty in this manual or a Harley
Davidson dealer for details.

Important Moving Information

If you move from your present address, or sell your motorcycle, please fill out and mail the post
card at the back of this manual. This is necessary in the event that the Company needs to contact
the owner concerning information that could affect the safe operation of this motorcycle.

California Evaporative Emission Controls: 2009 Models

All new model year 2009 HarleyDavidson motorcycles sold in the State of California are
equipped with an evaporative emission control system. This system is designed to meet the
CARB regulations in effect at the time of manufacture.

The system requires a small amount of maintenance. Periodic inspection is required to make sure
hoses are properly routed, not kinked or blocked and that all fittings are secure. Mounting
hardware should also be checked periodically for tightness.
EPA Noise Regulations in the United States

EPA noise regulations require that the following statements be included in the Owner's Manual.

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the
following acts or the causing thereof: (1) The removal or rendering inoperative by any person
other than for purposes of maintenance, repair, or replacement of any device or element of design
incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the
ultimate purchaser or while it is in use, or (2) the use of the vehicle after such device or element of
design has been removed or rendered inoperative by any person.

AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED
BELOW.

1. Replacing the muffler(s) and/or the entire exhaust system with parts not certified to be noise
legal for street use.

2. Removing or modifying the muffler internal baffles in any way.

3. Replacing the air intake/cleaner assembly with one not certified to be noise legal for street
use.

4. Modifying the air intake/cleaner assembly in such a way as to make the vehicle no longer
noise legal for street use.

HarleyDavidson recommends that any and all noise related maintenance be done by an
authorized HarleyDavidson dealer using genuine HarleyDavidson parts.

Warranty/Service Information

Any authorized HarleyDavidson dealer is responsible for providing the warranty repair work on
your motorcycle. If you have any questions regarding warranty obligations contact your selling
dealer.

For normal service work or warranty work under the above conditions, you may obtain the name
and location of your nearest U.S. HarleyDavidson dealer by calling 18004909635 (toll free), in
any state except Alaska and Hawaii.
NOTE:

The number shown above is accessible only with a touchtone phone in the United States.

Reporting Safety Defects in United States

Safety defects must be reported to the National Highway Traffic Safety Administration (NHTSA)
and HarleyDavidson.

NHTSA Statement

If you believe that your vehicle has a defect which could cause a crash or could cause injury or
death, you should immediately inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying HarleyDavidson.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA
cannot become involved in individual problems between you, your dealer, or HarleyDavidson.

To contact NHTSA, refer to NHTSA Contacts.

NHTSA Contacts

ITEM DATA
Phone Call the Auto Safety Hot Line tollfree at 1888
DASH2DOT
Mail U.S. Department of Transportation, National
Highway Traffic Safety Administration, Office of
Defects Investigation, NVS210, 400 7th Street
S.W., Washington, D.C. 20590
Web www.nhtsa.dot.gov
site

You can also obtain other information about motor vehicle safety from the hot line.

Owner Transfer Identification Form

When purchasing a preowned HarleyDavidson or Buell, we encourage you to submit an Owner
Transfer Notification Form. It is critical that new owner information is communicated to Harley
Davidson. New owner information is required to be on file with HarleyDavidson to transfer an
Extended Service Plan Contract. HarleyDavidson is also required by the National Traffic and
Motor Vehicle Safety Act to notify all owners in the event of a recall. The form may be obtained at
any HarleyDavidson dealer.

Required Documentation for Imported Motorcycles

If a HarleyDavidson is imported into the United States, additional documentation is required to be
eligible for the United States Manufacturer's Limited Warranty. A HarleyDavidson dealer can
provide a form explaining the requirements.

Limited Motorcycle Warranty

2009 HARLEYDAVIDSON MOTORCYCLE LIMITED WARRANTY

24 Months/Unlimited Miles

HarleyDavidson warrants for any new 2009 HarleyDavidson motorcycle/sidecar that an
authorized HarleyDavidson dealer will repair or replace without charge any parts found under
normal use to be defective in factory materials or workmanship. Such repair and replacement will
be HarleyDavidson's sole obligation and the customer's sole remedy under this warranty.

THERE IS NO OTHER EXPRESS WARRANTY (OTHER THAN THE SEPARATE EMISSIONS
AND NOISE WARRANTIES) ON THE MOTORCYCLE. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE IS LIMITED TO THE
DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.

TO THE FULLEST EXTENT ALLOWED BY LAW, HARLEYDAVIDSON AND ITS DEALERS
SHALL NOT BE LIABLE FOR LOSS OF USE, INCONVENIENCE, LOST TIME, COMMERCIAL
LOSS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may have
other rights which vary from state to state.

The following terms and conditions apply to this warranty:

Duration

1. The duration of this limited warranty is twenty four months, starting from the earlier of (a) the
date of initial retail purchase and delivery from an authorized HarleyDavidson dealer, or (b)
the third anniversary of the last day of the model year of the motorcycle/sidecar. Your dealer
will submit an electronic Sales and Warranty Registration form to initiate your warranty.

2. Any unexpired portion of this limited warranty will be transferred to subsequent owners,
upon the resale of the motorcycle/sidecar during the warranty period.

Owner's Obligations

To obtain warranty service, return your motorcycle/sidecar at your expense within the warranty
period to an authorized dealer. Our dealer should be able to provide warranty service during
normal business hours and as soon as possible, depending upon the workload of the dealer's
service department and the availability of necessary parts.

HarleyDavidson Motor Company, P.O. Box 653, Milwaukee, Wisconsin 53201, U.S.A.

Exclusions

This warranty will not apply to any motorcycle/sidecar as follows:

1. Which has not been operated or maintained as specified in the Owner's Manual.

2. Which has been abused, misused, improperly stored, used "off the highway," or used for
racing or competition of any kind.

3. Which is not manufactured to comply with the laws of the market in which it is registered.

4. Installing offroad or competition parts to enhance performance may void all or part of your
new motorcycle warranty. See a HarleyDavidson dealer for details.

5. Acts of God, war, riot, insurrection, natural disasters, including, but not limited to, nuclear
contamination, lightning, dust storms, hail storms, ice storms, earthquakes, floods, or for
other circumstances out of HarleyDavidson's control.
Other Limitations

This warranty does not cover:

1. Parts and labor for normal maintenance as recommended in the Owner's Manual, or the
replacement of parts due to normal wear and tear including such items as the following:
tires, lubrication, oil and filter change, fuel system cleaning, battery maintenance, engine
tuneup, spark plugs, brake, clutch and chain/belt adjustment (including chain replacement).

2. Cosmetic concerns that arise as a result of owner abuse, lack of proper maintenance or
environmental conditions (except concerns that result from defects in material or
workmanship, which are covered by this warranty for the duration of the warranty period).

3. Any cosmetic condition existing at the time of retail delivery that has not been documented
by the selling dealer prior to retail delivery.

4. Defects or damage to the motorcycle caused by alterations outside of HarleyDavidson
factory specifications.

Important: Read Carefully

1. Our dealers are independently owned and operated and may sell other products. Because
of this, HARLEYDAVIDSON IS NOT RESPONSIBLE FOR THE SAFETY, QUALITY, OR
SUITABILITY OF ANY NONHARLEYDAVIDSON PART, ACCESSORY OR DESIGN
MODIFICATION INCLUDING LABOR WHICH MAY BE SOLD AND/OR INSTALLED BY
OUR DEALERS.

2. This warranty is a contract between you and the manufacturer. It is separate and apart from
any warranty you may receive or purchase from the dealer. The dealer is not authorized to
alter, modify, or in any way change the terms and conditions of this warranty.

3. Any warranty work or parts replacement authorized by the manufacturer will not preclude
the manufacturer from later relying on any exclusion where applicable.

Limited Noise Warranty

2009 HARLEYDAVIDSON MOTORCYCLE NOISE CONTROL SYSTEM LIMITED
WARRANTY

The following warranty applies to the noise control system, is in addition to the MOTORCYCLE
LIMITED WARRANTY and EMISSION CONTROL SYSTEM LIMITED WARRANTY, and applies
only to motorcycles sold in the U.S.

HarleyDavidson Motor Company warrants that this vehicle is designed and built so as to conform
at the time of sale with applicable regulations of the U.S. Environmental Protection Agency (as
tested following F76 DriveBy test procedure) and that it is free from defects in materials and
workmanship which would cause this motorcycle not to meet U.S. Environmental Protection
Agency Standards within 1 year or 3,730 miles (6,000 kilometers) whichever expires first. Any
unexpired portion of this limited warranty will be transferred to subsequent owners, upon the
resale of the motorcycle during the warranty period.
THERE IS NO OTHER EXPRESS WARRANTY (OTHER THAN THE SEPARATE
MOTORCYCLE AND EMISSIONS WARRANTIES) ON THE MOTORCYCLE. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE IS LIMITED
TO THE DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.

The warranty period shall begin on the date the motorcycle is delivered to the first retail purchaser
or, if the motorcycle is placed in service as a demonstrator or company vehicle prior to sale at
retail, on the date it is first placed in service.

THE FOLLOWING ITEMS ARE NOT COVERED BY THE NOISE CONTROL SYSTEM
WARRANTY

1. Failures which arise as a result of misuse, alterations, or accident as specified in the
Owner's Manual.

2. Replacing, removing, or modifying any portion of the NOISE CONTROL SYSTEM
(consisting of the exhaust system and air intake/cleaner assembly) with parts not certified to
be legal for street use.

3. Any motorcycle on which the odometer mileage has been changed so that the mileage
cannot be determined.

4. TO THE FULLEST EXTENT ALLOWED BY LAW, HARLEYDAVIDSON AND ITS
DEALERS SHALL NOT BE LIABLE FOR LOSS OF USE, INCONVENIENCE, LOST TIME,
COMMERCIAL LOSS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.

Other Rights

This warranty gives you specific legal rights, and you may have other rights which vary from state
to state.

Recommendations for Required Maintenance

It is recommended that any noise system maintenance be performed by an authorized Harley
Davidson dealer using genuine HarleyDavidson replacement parts. The maintenance,
replacement or repair of the noise control system may be performed by any other qualified service
outlet or individual. Nongenuine parts may be used only if such parts are certified to comply with
U.S. Environmental Protection Agency Standards.

HarleyDavidson Motor Company, P.O. Box 653, Milwaukee, Wisconsin 53201, U.S.A.

Limited Emission Warranty

2009 HARLEYDAVIDSON EMISSION CONTROL SYSTEM LIMITED WARRANTY

The following warranty applies to the emission control system, is in addition to the LIMITED
MOTORCYCLE WARRANTY and NOISE CONTROL SYSTEM LIMITED WARRANTY, and
applies only to motorcycles sold in the U.S.

HarleyDavidson Motor Company warrants that this vehicle is designed and built so as to conform
at the time of sale with applicable regulations of the U.S. Federal Environmental Protection
Agency, and that it is free from defects in materials and workmanship which would cause this
motorcycle not to meet U.S. Environmental Protection Agency Standards within 5 years or 18,641
miles (30,000 kilometers) whichever expires first. Any unexpired portion of this limited warranty
will be transferred to subsequent owners, upon the resale of the motorcycle during the warranty
period.

THERE IS NO OTHER EXPRESS WARRANTY (OTHER THAN THE SEPARATE
MOTORCYCLE AND NOISE WARRANTIES) ON THE MOTORCYCLE. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE IS LIMITED
TO THE DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.

THE FOLLOWING ITEMS ARE NOT COVERED BY THE EMISSION CONTROL SYSTEM
WARRANTY

1. Failures which arise as a result of misuse, alterations, accident or nonperformance of
maintenance as specified in the Owner's Manual.

2. The replacement of parts (such as spark plugs, fuel and oil filters, etc.) used in required
maintenance.

3. Any motorcycle on which the odometer mileage has been changed so that the mileage
cannot be determined.

4. TO THE FULLEST EXTENT ALLOWED BY LAW, HARLEYDAVIDSON AND ITS
DEALERS SHALL NOT BE LIABLE FOR LOSS OF USE, INCONVENIENCE, LOST TIME,
COMMERCIAL LOSS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.

Other Rights

This warranty gives you specific legal rights, and you may have other rights which vary from state
to state.

Recommendations for Required Maintenance

It is recommended that any emission system maintenance be performed by an authorized Harley
Davidson dealer using genuine HarleyDavidson replacement parts. The maintenance,
replacement or repair of the emissions control system may be performed by any other qualified
service outlet or individual. Nongenuine parts may be used only if such parts are certified to
comply with U.S. Environmental Protection Agency Standards.

HarleyDavidson Motor Company, P.O. Box 653, Milwaukee, Wisconsin 53201, U.S.A.

Maintenance Scheduling

Regular Service Intervals

Regular lubrication and maintenance will help keep your new HarleyDavidson operating at peak
performance. Your HarleyDavidson dealer knows best how to service your motorcycle with
factory approved methods and equipment assuring you of thorough and competent workmanship.
NOTES:

Refer to Regular Service Intervals: 2009 Dyna Models. Regular maintenance interval
operations are required to keep your new motorcycle warranty in force. The use of other
than HarleyDavidson approved parts and service procedures may void the warranty. Any
alterations to the emission system components, such as the exhaust system, may be in
violation of Federal and State laws.
Refer to Owner's Maintenance Records. When servicing your motorcycle, bring this
owner's manual to the dealership and complete information needed in the blank columns
listed.

If you operate your motorcycle under adverse conditions
(severe cold, extreme heat, very dusty environment, very
bad roads, through standing water, etc.), you should
perform the regular maintenance intervals more frequently
to ensure the safe operation of your motorcycle. Failure to
maintain your motorcycle could result in death or serious
injury. (00094a)

Regular Service Intervals: 2009 Dyna Models

ITEM PROCEDURE 1000 5000 10,000 15,000 20,000 25,000 NOTES

SERVICED MI. MI. MI. MI. MI. MI.

1600 8000 16,000 24,000 32,000 40,000

KM KM KM KM KM KM
Engine oil and Replace X X X X X X
filter
Oil lines and Inspect for leaks X X X X X X 1
brake system
Air cleaner Inspect, service as required X X X X X X
Air cleaner Inspect, service as required X X X X X X

Tires Check pressure, inspect X X X X X X
tread
Wheel spokes Check tightness X X X 1, 4
Primary Replace X X X
chaincase
lubricant
Transmission Replace X X
lubricant
Clutch Check adjustment X X X X X X 1
Rear belt and Inspect, adjust belt X X X X X X 1
sprockets
Throttle, brake Check, adjust and lubricate X X X X X X 1
and clutch
controls
Jiffy stand Inspect and lubricate X X X 1
Fuel, lines and Inspect for leaks X X X X X X 1
fittings
Fuel pump filter Replace X 1
Brake fluid Check levels and condition X X X X X X 5
Brake pads Inspect for wear X X X X X X
and discs
Spark plugs Inspect X X X X X X
Replace X
Electrical Check operation X X X X X X
equipment and
switches
Front fork oil Replace 1, 6
Steering head Adjust X X X 1, 2
bearings
Rear fork Inspect every 30,000 miles 48,000 1
bearings kilometers
Critical Check tightness X X X 1
fasteners
Engine mounts Inspect X X 1
and stabilizer
links
Battery Check battery and clean 3
connections
Exhaust Inspect for leaks, cracks, X X X X X X 3
system and loose or missing
fasteners or heat shields
Road test Verify component and X X X X X X
system functions
NOTES: 1. Should be performed by an authorized HarleyDavidson dealer, unless you
have the proper tools, service data and are mechanically qualified.
2. Disassemble, lubricate and inspect every 30,000 miles 48,000 kilometers .

3. Perform annually.

4. Not all vehicles are equipped with spoke wheels. Consult appropriate topic in
service manual.

5. Replace D.O.T. 4 HYDRAULIC BRAKE FLUID and flush system every two
(2) years.

6. Disassemble, lubricate and inspect every 50,000 miles 80,000 kilometers .

Owner's Maintenance Records

SERVICE MILE INTERVAL DATE DEALER TECHNICIAN TECHNICIAN

NUMBER NAME SIGNATURE

1000 MI 1600 KM
5000 MI 8000 KM
10,000 MI 16,000 KM
15,000 MI 24,000 KM
20,000 MI 32,000 KM
25,000 MI 40,000 KM
30,000 MI 48,000 KM
35,000 MI 56,000 KM
40,000 MI 64,000 KM
45,000 MI 72,000 KM
50,000 MI 80,000 KM

Service Literature

Refer to Service Literature: 2009 Dyna Models. Visit any HarleyDavidson dealer or go to
www.harleydavidson.com to purchase a service or parts manual for your motorcycle. Factory
authorized manuals are the most complete and detailed source of information outside of your
HarleyDavidson dealer.

Service Literature: 2009 Dyna Models

DOCUMENT LANGUAGE PART NUMBER

Service Manual English 9948109
Electrical Diagnostics Manual English 9949609
Service and Electrical Diagnostics Manual French 9948109F
Service and Electrical Diagnostics Manual German 9948109G
Service and Electrical Diagnostics Manual Spanish 9948109S
Service and Electrical Diagnostics Manual Italian 9948109I
Parts Catalog English 9943909
Parts Catalog English 9943909

HD Michigan, Inc. Trademark Information

Harley, HarleyDavidson, HD, Bar & Shield, Digital Tech, Digital Technician, Digital Technician II,
Destroyer, Deuce, Dyna, Electra Glide, Evolution, Fat Boy, Glaze, Gloss, HD, HDnet.com, HD,
Harley, Heritage Softail, Heritage Springer, Low Rider, Night Rod, Night Train, Profile, Revolution,
Road Glide, Road King, Rocker, Softail, Sportster, Sun Ray, Sunwash, Tech Link, Twin Cam 88,
Twin Cam 88B, Twin Cam 96, Twin Cam 96B, Twin Cam 103, Twin Cam 103B, Twin Cam 110,
Twin Cam 110B, TourPak, Screamin' Eagle, Softail, Super Guide, Super Premium, SYN3, Ultra
Glide, VRod, VRSC, Wide Glide, and HarleyDavidson Genuine Motor Parts and Genuine Motor
Accessories are among the trademarks of HD Michigan, Inc.

Product Registered Marks

Allen, Amp Multilock, Bluetooth, Brembo, Delphi, Deutsch, Dunlop, Dynojet, Fluke, G.E.
Versilube, Gunk, Hydroseal, Hylomar, Kevlar, Lexan, Loctite, Lubriplate, Keps, K&N, Magnaflux,
Marson ThreadSetter Tool Kit, MAXI fuse, Molex, MPZ, Mulitilock, Novus, Packard, Pirelli,
Permatex, Philips, PJ1, Pozidriv, Robinair, S100, Sems, Snapon, Teflon, Threadlocker, Torca,
Torco, TORX, Tufoil, Tyco, Ultratorch, Velcro, XActo, and XM Satellite Radio are among the
trademarks of their respective owners.

2008 Harley Davidson Nightster 66549
0% (1)
2008 Harley Davidson Nightster 66549
146 pages
Harley-Davidson Road King Classic 105th Anniversary Edition (EFI) Owner - S Manuals
No ratings yet
Harley-Davidson Road King Classic 105th Anniversary Edition (EFI) Owner - S Manuals
188 pages
2016 Harley Davidson Road Glide Owner's Manual
No ratings yet
2016 Harley Davidson Road Glide Owner's Manual
246 pages
H-D Road King 103 Manual
No ratings yet
H-D Road King 103 Manual
177 pages
2019 Softail Parts
No ratings yet
2019 Softail Parts
572 pages
Harley Davidson MX250 - Owners Manual - 1978
100% (1)
Harley Davidson MX250 - Owners Manual - 1978
32 pages
en - US - 1991-1992 HARLEY-DAVIDSON® PARTS CATALOG - SOFTAIL® MODELS - Harley-Davidson SIP
No ratings yet
en - US - 1991-1992 HARLEY-DAVIDSON® PARTS CATALOG - SOFTAIL® MODELS - Harley-Davidson SIP
295 pages
2019 HD Sportster Parts Catalog 94000557 (SIP)
No ratings yet
2019 HD Sportster Parts Catalog 94000557 (SIP)
364 pages
2004 Sportster Models Parts Catalog
No ratings yet
2004 Sportster Models Parts Catalog
265 pages
H-D 2015 Touring Models Parts Catalog
100% (1)
H-D 2015 Touring Models Parts Catalog
539 pages
Harley-Davidson Electra Glide Motorcycle 1970 Owner's Manual - Ebook
No ratings yet
Harley-Davidson Electra Glide Motorcycle 1970 Owner's Manual - Ebook
64 pages
02-04 VICTORY Service Manual 02-04
No ratings yet
02-04 VICTORY Service Manual 02-04
464 pages
2017 Harley Davidson Maintenance Schedules
No ratings yet
2017 Harley Davidson Maintenance Schedules
25 pages
Manual Harley FLHRCI PDF
50% (2)
Manual Harley FLHRCI PDF
20 pages
2008 Harley Davidson Night Rod 28
No ratings yet
2008 Harley Davidson Night Rod 28
137 pages
2003 Harley V-Rod VRSCA Owners Manual 99736-03
100% (1)
2003 Harley V-Rod VRSCA Owners Manual 99736-03
187 pages
Custom CD Creations Offer
No ratings yet
Custom CD Creations Offer
744 pages
Service Manual 2010 HD Sportster Service Manual 99484-10 (Preview)
0% (1)
Service Manual 2010 HD Sportster Service Manual 99484-10 (Preview)
6 pages
2008 Harley Davidson Softail Deluxe 19
No ratings yet
2008 Harley Davidson Softail Deluxe 19
150 pages
'70-'78 Harley-Davidson FL FLH FX FXE FXS Shovelhead Service Manual PDF
No ratings yet
'70-'78 Harley-Davidson FL FLH FX FXE FXS Shovelhead Service Manual PDF
232 pages
2005 Harley Davidson Cvo Fat Boy 66385
No ratings yet
2005 Harley Davidson Cvo Fat Boy 66385
131 pages
Catalogue Screaming Eagle
No ratings yet
Catalogue Screaming Eagle
136 pages
Honda Sabre V65 700 1985 Catalog Folder Staring
100% (2)
Honda Sabre V65 700 1985 Catalog Folder Staring
8 pages
Compensaver Installation Instructions
No ratings yet
Compensaver Installation Instructions
4 pages
MAINT2016 - PDF - en - US - All 2016 Maintenance Service Schedules PDF (Excluding Japan) - Harley-Davidson SIP
No ratings yet
MAINT2016 - PDF - en - US - All 2016 Maintenance Service Schedules PDF (Excluding Japan) - Harley-Davidson SIP
35 pages
FLHTC
100% (1)
FLHTC
282 pages
Harley Davidson 2018 Wiring Diagrams High-Res
No ratings yet
Harley Davidson 2018 Wiring Diagrams High-Res
55 pages
2011 PP
100% (1)
2011 PP
56 pages
Sportster Diagnostic Codes Guide
No ratings yet
Sportster Diagnostic Codes Guide
4 pages
U109110 Binay MM-I Term1 Assignment
No ratings yet
U109110 Binay MM-I Term1 Assignment
21 pages
Puch Service Manuals
No ratings yet
Puch Service Manuals
127 pages
2005 Harley Davidson Sportster 883 66418
100% (1)
2005 Harley Davidson Sportster 883 66418
136 pages
Harley Davidson 1941 78 FL FX Electra Glide Super Glide Parts Catalog
No ratings yet
Harley Davidson 1941 78 FL FX Electra Glide Super Glide Parts Catalog
251 pages
Moto Frame ID Numbers
No ratings yet
Moto Frame ID Numbers
10 pages
Compensaver Oil Delivery System Installation Instructions Revised 08-15
No ratings yet
Compensaver Oil Delivery System Installation Instructions Revised 08-15
5 pages
2005 VRSCB V Rod Owner's Manual
No ratings yet
2005 VRSCB V Rod Owner's Manual
136 pages
Manuals For Harley Davidson
100% (2)
Manuals For Harley Davidson
1 page
2016 Harley-Davidson Dyna Service Manual - Chapter 2 - Chasis
No ratings yet
2016 Harley-Davidson Dyna Service Manual - Chapter 2 - Chasis
144 pages
Big Twin or Kit
100% (1)
Big Twin or Kit
3 pages
1993-94 All Model Parts Catalog Parts
100% (1)
1993-94 All Model Parts Catalog Parts
378 pages
Harley Davidson Shovelhead 1978-1984. Service Manual
No ratings yet
Harley Davidson Shovelhead 1978-1984. Service Manual
410 pages
1998 Harley Savidson FLT Models Parts Catalog
100% (2)
1998 Harley Savidson FLT Models Parts Catalog
584 pages
HD Touring 2016 - Parts
No ratings yet
HD Touring 2016 - Parts
432 pages
2016 Victory Gunner 70482
No ratings yet
2016 Victory Gunner 70482
106 pages
en - US - 2018 HARLEY-DAVIDSON® PARTS CATALOG - SOFTAIL® MODELS - Harley-Davidson SIP
No ratings yet
en - US - 2018 HARLEY-DAVIDSON® PARTS CATALOG - SOFTAIL® MODELS - Harley-Davidson SIP
477 pages
Document Page Numbers Only
75% (4)
Document Page Numbers Only
182 pages
crf300l SERVICE DATA
100% (1)
crf300l SERVICE DATA
4 pages
HD 2008 FLT Police Model Supplement Manual 99483-08SP 2
No ratings yet
HD 2008 FLT Police Model Supplement Manual 99483-08SP 2
126 pages
Triumph Motorcycle Guide
No ratings yet
Triumph Motorcycle Guide
81 pages
Softail 2018 Service Manual Harley Davidson 94000
No ratings yet
Softail 2018 Service Manual Harley Davidson 94000
1 page
Harley Davidson Touring Fork Oil Change - The HERD
No ratings yet
Harley Davidson Touring Fork Oil Change - The HERD
7 pages
Street Triple S
100% (1)
Street Triple S
245 pages
H-D Job Codes 2010
No ratings yet
H-D Job Codes 2010
274 pages
HD Painted Parts PDF
No ratings yet
HD Painted Parts PDF
46 pages
KX125 KX250: Service Manual
No ratings yet
KX125 KX250: Service Manual
242 pages
Harley-Davidson Handlebar Installation Requirements
No ratings yet
Harley-Davidson Handlebar Installation Requirements
165 pages
Serviceinfo Harley Davidson Com Sip Service Document 273141
100% (1)
Serviceinfo Harley Davidson Com Sip Service Document 273141
481 pages
2008 Harley Davidson Dyna Fat Bob 15
No ratings yet
2008 Harley Davidson Dyna Fat Bob 15
123 pages
2008 Harley Davidson Cvo Dyna 8
No ratings yet
2008 Harley Davidson Cvo Dyna 8
86 pages
2008 Harley Davidson 7
No ratings yet
2008 Harley Davidson 7
123 pages
Saarbike - de Shop-Vergaser Tabellen Yamaha - HTM
No ratings yet
Saarbike - de Shop-Vergaser Tabellen Yamaha - HTM
1 page
Fork Fluid Info
No ratings yet
Fork Fluid Info
2 pages
Saarbike - de Shop-Vergaser Tabellen Kawasaki - HTM
No ratings yet
Saarbike - de Shop-Vergaser Tabellen Kawasaki - HTM
1 page
Warning: No Smoking! No Open Flame! While Installing Your Dynojet Kit
No ratings yet
Warning: No Smoking! No Open Flame! While Installing Your Dynojet Kit
2 pages
2003-2013 KTM 950-990 ADV SUPERDUKE SMT SE Shock Absorber
100% (1)
2003-2013 KTM 950-990 ADV SUPERDUKE SMT SE Shock Absorber
79 pages
Warning: No Smoking! No Open Flame! While Installing Your Jet Kit
No ratings yet
Warning: No Smoking! No Open Flame! While Installing Your Jet Kit
2 pages
Motorcycle Exhaust Enthusiasts
No ratings yet
Motorcycle Exhaust Enthusiasts
20 pages
11 Steps To Survival
No ratings yet
11 Steps To Survival
26 pages
Silverado 2000 Gussi VCM
No ratings yet
Silverado 2000 Gussi VCM
7 pages
340 Lca
100% (2)
340 Lca
42 pages
GMStandard Labor Op Codes
No ratings yet
GMStandard Labor Op Codes
3 pages
Sponsor Pitch Deck Revved Up FIN
No ratings yet
Sponsor Pitch Deck Revved Up FIN
11 pages
Nissan Navara Workshop Manual CL
91% (11)
Nissan Navara Workshop Manual CL
22 pages
Disc Brakes
100% (1)
Disc Brakes
33 pages
OPW 19DEF Series Industrial Automatic Nozzle Materials
No ratings yet
OPW 19DEF Series Industrial Automatic Nozzle Materials
1 page
Negotiation 3 - Robert Gibb 2024
No ratings yet
Negotiation 3 - Robert Gibb 2024
54 pages
Grove RT600E
50% (2)
Grove RT600E
20 pages
ENG159753800 Calculations and Loads ALL
No ratings yet
ENG159753800 Calculations and Loads ALL
12 pages
Fast Rescue Boat
No ratings yet
Fast Rescue Boat
2 pages
Man B&W: Main Bearing
No ratings yet
Man B&W: Main Bearing
70 pages
Premium Hydraulic Oils for All-Weather Use
No ratings yet
Premium Hydraulic Oils for All-Weather Use
1 page
Kioti CK3710 (H), CK4210 (H) Tractor Operator's Manual
No ratings yet
Kioti CK3710 (H), CK4210 (H) Tractor Operator's Manual
15 pages
2007 Chevy Colorado Wiring Diagrams
89% (9)
2007 Chevy Colorado Wiring Diagrams
83 pages
2015 Kia Sorento 36481 PDF
100% (1)
2015 Kia Sorento 36481 PDF
543 pages
Cres Cor CCB-120A 2 Door Heated Banquet Cabinet - 120V, 1650W
No ratings yet
Cres Cor CCB-120A 2 Door Heated Banquet Cabinet - 120V, 1650W
2 pages
Englisch Bal - 18100-05-02 LR 1600 - 2 PDF
0% (3)
Englisch Bal - 18100-05-02 LR 1600 - 2 PDF
1,206 pages
Codificaciones y Moods para Volkswagen
No ratings yet
Codificaciones y Moods para Volkswagen
8 pages
PM Clinic Wd600-6r SN 60001 - Up
No ratings yet
PM Clinic Wd600-6r SN 60001 - Up
8 pages
Auto Drive Train Warranty Tscs Vaps Eng Budget
No ratings yet
Auto Drive Train Warranty Tscs Vaps Eng Budget
9 pages
03704A - 2022 - 08 - 10 ИНДЕКС SB EXTRA 300
No ratings yet
03704A - 2022 - 08 - 10 ИНДЕКС SB EXTRA 300
5 pages
Heavy Duty Forklift Tipping Skips
No ratings yet
Heavy Duty Forklift Tipping Skips
2 pages
GR 00
No ratings yet
GR 00
26 pages
Volvo A35d Articulated Hauler - Parts Manual - PDF Download
No ratings yet
Volvo A35d Articulated Hauler - Parts Manual - PDF Download
33 pages
PN3000 and PN4000 Pneumatic Actuators For LE Valve Spares
No ratings yet
PN3000 and PN4000 Pneumatic Actuators For LE Valve Spares
2 pages
Bendix Tu-Flo 600
No ratings yet
Bendix Tu-Flo 600
16 pages
CAN Bus Diagnostics Guide
No ratings yet
CAN Bus Diagnostics Guide
142 pages
B-65452EN 01 Description
100% (2)
B-65452EN 01 Description
460 pages
Technical Data: Reversible Vibratory Plates BPR 70/70 D, BPR 100/80 D
No ratings yet
Technical Data: Reversible Vibratory Plates BPR 70/70 D, BPR 100/80 D
2 pages

2009 Harley Davidson Fat Bob 28

Uploaded by

2009 Harley Davidson Fat Bob 28

Uploaded by

2009

POSITION DESCRIPTION POSSIBLE VALUES

CODE MODEL CODE MODEL

LABEL PART NO. DESCRIPTION LOCATION

DRIVE ITEM NUMBER OF TEETH

ITEM FXD FXDC FXDL FXDB FXDF

ITEM FXD FXDC FXDL FXDB FXDF

ITEM FXD FXDC FXDL FXDB FXDF

MODEL LOAD TIRE PRESSURE (COLD)

MODEL MOUNT SIZE NUMBER

LAMP DESCRIPTION BULBS CURRENT H­D

MODEL LOCATION AND OPERATION SWITCH FUNCTION

STEP ACTION WAIT FOR CONFIRMATION NOTES

STEP ACTION WAIT FOR CONFIRMATION NOTES

GEAR CHANGE MPH KPH

GEAR CHANGE MPH KPH

H­D TYPE VISCOSITY H­D LOWEST AMBIENT COLD WEATHER STARTS

MODELS INCHES MILLIMETERS

READING PERCENT 3 AMP 6 AMP 10 AMP 20 AMP

(VOLTS) OF CHARGE CHARGER CHARGER CHARGER CHARGER

40 minutes 50 minutes 5 minutes

15 minutes 40 minutes 35 minutes

30 minutes 5 minutes 5 minutes

PRODUCT PART FRAME BODY WHEELS DENIM

ITEM PROCEDURE 1000 5000 10,000 15,000 20,000 25,000 NOTES

1600 8000 16,000 24,000 32,000 40,000

SERVICE MILE INTERVAL DATE DEALER TECHNICIAN TECHNICIAN

NUMBER NAME SIGNATURE

DOCUMENT LANGUAGE PART NUMBER

You might also like

LAMP DESCRIPTION BULBS CURRENT HD

HD TYPE VISCOSITY HD LOWEST AMBIENT COLD WEATHER STARTS