Router>en HQ#

Router#conf t %SYS-5-CONFIG_I: Configured from

Enter configuration commands, one per line. console by console
End with CNTL/Z.
Router(config)#hostname HQ HQ#copy run start
HQ(config)#int fa0/0 Destination filename [startup-config]?
HQ(config-if)#ip address 192.168.1.129 Building configuration...
255.255.255.192 [OK]
HQ(config-if)#no shutdown HQ#exit

HQ(config-if)#
%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol

on Interface FastEthernet0/0, changed state
to up Router>en
Router#conf t
HQ(config-if)#exit Enter configuration commands, one per line.
HQ(config)#int s0/0/0 End with CNTL/Z.
HQ(config-if)#ip address 192.168.1.225 Router(config)#hostname B1
255.255.255.252 B1(config)#int fa0/0
HQ(config-if)#no shutdown B1(config-if)#ip address 192.168.1.1
255.255.255.128
%LINK-5-CHANGED: Interface B1(config-if)#no shutdown
Serial0/0/0, changed state to down
HQ(config-if)#exit B1(config-if)#
HQ(config)#int s0/0/1 %LINK-5-CHANGED: Interface
HQ(config-if)#ip address 192.168.1.229 FastEthernet0/0, changed state to up
255.255.255.252
HQ(config-if)#clock rate 64000 %LINEPROTO-5-UPDOWN: Line protocol
HQ(config-if)#no shutdown on Interface FastEthernet0/0, changed state
to up
%LINK-5-CHANGED: Interface
Serial0/0/1, changed state to down B1(config-if)#exit
HQ(config-if)#exit B1(config)#int S0/0/0
HQ(config)#line console 0 B1(config-if)#ip address 192.168.1.226
HQ(config-line)#password cisco 255.255.255.252
HQ(config-line)#login B1(config-if)#clock rate 64000
HQ(config-line)#exit B1(config-if)#no shutdown
HQ(config)#line vty 0
HQ(config-line)#password cisco B1(config-if)#
HQ(config-line)#login %LINK-5-CHANGED: Interface
HQ(config-line)#exit Serial0/0/0, changed state to up
HQ(config)#enable secret class
HQ(config)#exit B1(config-if)#exit
B1(config)# B2(config)#int S0/0/0
%LINEPROTO-5-UPDOWN: Line protocol B2(config-if)#ip address 192.168.1.226
on Interface Serial0/0/0, changed state to up 255.255.255.252
B2(config-if)#clock rate 64000
B1(config)#line console 0 B2(config-if)#no shutdown
B1(config-line)#password cisco
B1(config-line)#login B2(config-if)#
B1(config-line)#exit %LINK-5-CHANGED: Interface
B1(config)#line vty 0 Serial0/0/0, changed state to up
B1(config-line)#password cisco
B1(config-line)#login B2(config-if)#exit
B1(config-line)#exit B2(config)#
B1(config)#enable secret class %LINEPROTO-5-UPDOWN: Line protocol
B1(config)#exit on Interface Serial0/0/0, changed state to up
B1#
%SYS-5-CONFIG_I: Configured from B2(config)#line console 0
console by console B2(config-line)#password cisco
B2(config-line)#login
B1#copy run start B2(config-line)#exit
Destination filename [startup-config]? B2(config)#line vty 0
Building configuration... B2(config-line)#password cisco
[OK] B2(config-line)#login
B1#exit B2(config-line)#exit
B2(config)#enable secret class
B2(config)#exit
B2#
%SYS-5-CONFIG_I: Configured from
Router>en console by console
Router#conf t
Enter configuration commands, one per line. B2#copy run start
End with CNTL/Z. Destination filename [startup-config]?
Router(config)#hostname B2 Building configuration...
B2(config)#int fa0/0 [OK]
B2(config-if)#ip address 192.168.1.1 B2#exit
255.255.255.128
B2(config-if)#no shutdown

B2(config-if)#
%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol

on Interface FastEthernet0/0, changed state
to up

B2(config-if)#exit