INTERNATIONAL ISO

STANDARD 9244

Second edition
2008-06-15
AMENDMENT 1
2016-03-01

Earth-moving machinery — Machine

safety labels — General principles
AMENDMENT 1
Engins de terrassement — Étiquetage de sécurité de la machine —
Principes généraux
AMENDEMENT 1
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

Reference number
ISO 9244:2008/Amd.1:2016(E)

© ISO 2016
ISO 9244:2008/Amd.1:2016(E)


iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

COPYRIGHT PROTECTED DOCUMENT

© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org

ii  © ISO 2016 – All rights reserved

 ISO 9244:2008/Amd.1:2016(E)


Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
iTeh STANDARD PREVIEW
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
(standards.iteh.ai)
ISO 9244-1:2008/Amd. 1 was prepared by ISO/TC 127, Earth-moving machinery, Subcommittee SC 2,
Safety, ergonomics and general requirements.
ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

© ISO 2016 – All rights reserved  iii

 iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016
 ISO 9244:2008/Amd.1:2016(E)

Earth-moving machinery — Machine safety labels —

General principles
AMENDMENT 1
Page 7, 4.7.3
Replace 4.7.3 and Figure 5, including the figure title, with the following:
4.7.3 Communicating “do not” messages
4.7.3.1 Hazard avoidance pictorials are often used to communicate, in graphical form, one or more of
the following types of “do not” messages:
— a specific action that should not be taken, because taking the action can result in a hazardous
situation;
— a specific location that should be avoided, because being in the location can result in a hazardous
situation;
— a specific activity that should be avoided, because engaging in the activity can result in a hazardous
situation. iTeh STANDARD PREVIEW
4.7.3.2 The “do not” messages are(standards.iteh.ai)
communicated graphically by means of a red diagonal cross placed
over the pictorial for the action that should not be taken, the location that should be avoided, or the
activity that should be avoided. TheISO red9244:2008/Amd
diagonal cross is shown in Figure 5. The red diagonal cross
1:2016
is the safety-related application of IEC 60417-6287, which has the general meaning of negation in
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
accordance with IEC 80416-1. 8d08b77dd738/iso-9244-2008-amd-1-2016

Figure 5 — Red diagonal cross

4.7.3.3 Sizing of the red diagonal cross depends on how it is used with a particular pictorial. It is
important that the red diagonal cross is sufficiently large to be easily recognized, but care shall be
taken to avoid obscuring any critical detail of the pictorial. The red diagonal cross may be placed over

© ISO 2016 – All rights reserved  1

ISO 9244:2008/Amd.1:2016(E)


the entire pictorial or over only the portion of the pictorial that represents the specific action, location,
or activity to be avoided.
4.7.3.4 The red prohibition symbol (circle with diagonal bar; see also D.9.2) may be used to communicate
a “do not” message, provided that the requirements of ISO 3864-1, ISO 3864-2, and ISO 3864-3 for
prohibition safety signs are adhered to.

Page 8, 4.7.5
Replace 4.7.5 and Figure 7, including the figure title, with the following:
4.7.5 Combined pictorials
In specific circumstances, a hazard description pictorial and a hazard avoidance pictorial may be
combined in a single panel. An example is shown in Figure 7.

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

Figure 7 — Combined pictorial in a single panel

2  © ISO 2016 – All rights reserved

 ISO 9244:2008/Amd.1:2016(E)


Page 10, Table 1

Replace Table 1, including the table title, with the following:

Table 1 — Colour regions: chromaticity coordinates and luminance factor of ordinary materials
Corner points of colour region
CIE Standard illuminant D65 Luminance factor
Colour CIE 2° standard colorimetric observer β
region 1 2 3 4 Minimum Maximum
x 0,705 0,592 0,574 0,663
Red 0,07 0,20
y 0,295 0,291 0,351 0,337
x 0,603 0,538 0,508 0,563
Orange 0.21
y 0,397 0,382 0,412 0,436
x 0,475 0,538 0,470 0,427
Yellow 0,45 0,70
y 0,525 0,462 0,424 0,472
x 0,350 0,295 0,285 0,340
White 0,75
y 0,360 0,305 0,315 0,370
x 0,385 0,300 0,260 0,345
Black 0,03
y 0,355 0,270 0,310 0,295

Page 11, 5.3.4

iTeh STANDARD PREVIEW
Revise 5.3.4 to read as follows:
(standards.iteh.ai)
5.3.4 The diagonal cross specified ISO in 4.7.3 shall be red.
9244:2008/Amd See Annex D for more information.
1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

© ISO 2016 – All rights reserved  3

ISO 9244:2008/Amd.1:2016(E)


Page 33, Annex B

Replace Figure B.13 with the following:

Figure B.13
iTeh — Do not jump start
STANDARD engine
PREVIEW
Page 34, Annex B (standards.iteh.ai)
Replace Figure B.15 with the following: ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

Figure B.15 — Do not ride on fender

4  © ISO 2016 – All rights reserved

 ISO 9244:2008/Amd.1:2016(E)


Replace Figure B.16 with the following:

Figure B.16 — Do not reach into crushing area

Replace Figure B.17 with the following:

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 9244:2008/Amd 1:2016
https://standards.iteh.ai/catalog/standards/sist/49ad7fdb-605e-46dd-9441-
8d08b77dd738/iso-9244-2008-amd-1-2016

Figure B.17 — Do not stand under bucket

© ISO 2016 – All rights reserved  5