The information in this document is reviewed regularly and any

necessary changes will be incorporated in the next revision.

We welcome any suggestions for improvement.

This manual is for the exclusive use of Electronic Data Devices customers
and distributors. The reproduction, transmission or use of this document
or its contents is not permitted without the expressed written permission of
Electronic Data Devices.

January 2004

P.O. Box 12128

Phone Fax E-mail Website
Odessa, Texas 79768
432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Table of Contents

EDD Contact Information 04

Flow Range Chart 05
Pressure Drop Curves 06
Standard Threaded Meter 07
Installation Drawings 08 - 21
Hex Body Threaded Meter 22
Installation Drawings 23 -27
Cast Body Threaded Meter 28
Installation Drawing 29
Grooved Meter 30
Installation Drawings 31 - 51
Standard Flanged Meters 52
Installation Drawings 53 - 87
1502 Union Meters 88
Installation Drawings 89 - 92
Square Flanged Meters 93
Installation Drawings 94, 95
Standard Meter Repair Kits 96
3/8” - 3” Repair Kit Installation Instructions 97
4” & Up Repair Kit Installation Instructions 98
Between Flange Meters 99
Installation Drawings 100 - 113
4” Long Between Flange Meters 114
Installation Drawings 115 - 119
Between Flange Ring Joint Meters 120
Installation Drawings 121 - 130
Between Flange Repair Kits 131
Between Flange Repair Kit Installation Instructions 132
EDD-600 Totalizer 133
Installation Drawings 134, 135
EDD-340 4 - 20 mA Converter 136
EDD-530 Pulse Output Card 137
Preamplifier Spec Sheet 138
4.0420 FTC Converter Spec Sheet 140
4.303 Magnetic Pickup 142
4.303 Magnetic Pickup Spec Sheet 143
4.304 Magnetic Pickup Spec Sheet 144
4.5015U Magnetic Pickup 145
4.5015U Magnetic Pickup Spec Sheet 146
4.5024 Magnetic Pickup Spec Sheet 147
4.5050 Magnetic Pickup Spec Sheet 148
4.308T800 Magnetic Pickup Spec Sheet 149

P.O. Box 12128

Phone Fax E-mail Website
Odessa, Texas 79768
432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Threaded Turbine Flow Meters

Electronic Data Devices manufactures a complete line of turbine flow meters that are available
with ranges from 0.3 GPM to 5500 GPM covering a wide range of measurement applications.
Our turbine flow meters are manufactured to the highest quality standards and are available with
a wide range of end connections compatible with many applications. Some of the typical appli-
cations include: oilfield waterflood, production, well servicing, pipelines, mining, chemicals, food
and beverage industry, and most other liquid applications.

Threaded meters are available in the sizes below.

All threaded meters have a working pressure of 5000 psi except 3” and 4”, which are 3000 psi.

.37” X 1”-MNPT .75” X 2” MNPT 1” X 1”-MNPT 1.5” X 2” MNPT 3” X 3” FMNPT

.50” X 1” MNPT .87” X 1” MNPT 1” X 2” MNPT 2” X 2” FMNPT 4” X 4” FMNPT
.75” X 1” MNPT .87” X 2” MNPT 1.5” X 1.5” MNPT

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Threaded Turbine Flow Meters

Electronic Data Devices offers a complete line of turbine flow meters that are available with
ranges from 0.3 GPM to 5500 GPM covering a wide range of measurement applications. Our
turbine flow meters are manufactured to the highest quality standards, and are available with a
wide range of end connections compatible with many applications. Some of the typical applica-
tions include: oilfield waterflood, production, well servicing, pipelines, mining, chemicals, food
and beverage industry, and most other liquid applications.

Threaded meters are available in the sizes below.

All threaded meters have a working pressure of 5000psi except 3” and 4”, which are 3000 psi.
.37” X 1”-MNPT .75” X 2” MNPT 1” X 1”-MNPT 1.5” X 2” MNPT 3” X 3” FMNPT
.50” X 1” MNPT .87” X 1” MNPT 1” X 2” MNPT 2” X 2” FMNPT 4” X 4” FMNPT
.75” X 1” MNPT .87” X 2” MNPT 1.5” X 1.5” MNPT

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Threaded Turbine Flow Meters

Electronic Data Devices offers a line of threaded turbine flow meters with cast bodies that are
available with ranges from 0.3 GPM to 50 GPM covering a wide range of measurement applica-
tions. Our turbine flow meters are manufactured to the highest quality standards. Some of the
typical applications include: oilfield waterflood, production, well servicing, pipelines, mining,
chemicals, food and beverage industry, and most other liquid applications.

Threaded meters with a cast meter body are available in 1” x 1” MNPT.

All threaded meters have a working pressure of 5000 psi.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Grooved Turbine Flow Meters

Electronic Data Devices offers a complete line of turbine flow meters that are available with
ranges from 0.3 GPM to 5500 GPM covering a wide range of measurement applications.
Our turbine flow meters are manufactured to the highest quality standards, and are avail-
able with a wide range of end connections compatible with many applications. Some of the
typical applications include: oilfield waterflood, production, well servicing, pipelines, mining,
chemicals, food and beverage industry, and most other liquid applications.

Grooved end turbine flow meters are available in the sizes below. The maximum operating
psi is determined by the victaulic clamp rating.

.37” X 1” .75” X 2” 1” X 1” 2” X 2.5” 6” X 6”

.50” X 1” .87” X 1” 1” X 2” 3” X 3” 8” X 8”
.75” X 1” .87” X 2” 1.5” X 2” 4” X 4” 10” X 10”

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Standard Flanged
Turbine Flow Meters
Electronic Data Devices offers a complete line of turbine flow meters that are available
with ranges from 0.3 GPM to 5500 GPM covering a wide range of measurement applica-
tions. Our turbine flow meters are manufactured to the highest quality standards, and are
available with a wide range of end connections compatible with many applications. Some
of the typical applications include: oilfield waterflood, production, well servicing, pipe-
lines, mining, chemicals, food and beverage industry, and most other liquid applications.

Standard flanged turbine flow meters are available with raised face or ring joint ANSI
B16.5 rated flanges, carbon steel, 304SS or 316SS. Operating pressure will be deter-
mined by the ANSI flange series and ratings. Flanged meters are available with the follow-
ing ratings 150#,300#,600#, 900# and 1500# in the following sizes 1”,1.5”,2”,3”,
4”,6”,8” and 10”.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

1502 Union Turbine Flow Meters

Electronic Data Devices manufactures a line of 1502 union turbine flow meters that are available
with ranges from 5 GPM to 600 GPM covering a wide range of measurement applications. Our
turbine flow meters are manufactured to the highest quality standards. Some of the typical appli-
cations include: oilfield waterflood, production, well servicing, pipelines, mining, chemicals, food
and beverage industry, and most other liquid applications.

1502 union turbine flow meters are available in the following sizes: 1”, 1 1/2”, 2” and 3”.
All union meters have a working pressure of 15000 psi.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Square Flanged
Turbine Flow Meters
Electronic Data Devices offers a line of turbine flow meters that are available with ranges
from 5 GPM to 400 GPM covering a wide range of measurement applications. Our tur-
bine flow meters are manufactured to the highest quality standards. Some of the typical
applications include: oilfield waterflood, production, well servicing, pipelines, mining,
chemicals, food and beverage industry, and most other liquid applications.

Square flanged turbine flow meters are available with raised face 316SS schedule 160
flanges. Operating pressure is 3600 psi. Square flanged meters are available in the fol-
lowing sizes: 1”, 1 1/2” and 2”.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Standard Meter Repair Kits

Electronic Data Devices offers a broad line of turbine flow meter repair kits designed for our
meters and other popular brands. The kits are available for flow ranges of 0.3 to 5000
GPM and fit meter sizes of 3/8” to 10”.

Electronic Data Devices’ repair kits are manufactured to the highest quality standards. The re-
pair kits are manufactured of 316SS and CD4MCu for the rotors. Bearings are tungsten car-
bide and ceramic. The kits are calibrated in pulses per gallon for each kit, and may be used in
a wide range of applications including: oilfield waterflood, production, well servicing, pipe-
lines, mining, chemicals, food and beverage industry and most other liquid applications.

Repeatability: Within + 0.1% of indicated flow throughout the linear flow range.

Accuracy: Within + 1% of the reading Note: 3/8” + 2% of the reading.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

BF Series Turbine Flow Meters

Electronic Data Devices offers a complete line of turbine flow meters that are available with
ranges from 0.3 GPM to 5500 GPM covering a wide range of measurement applications.
Our turbine flow meters are manufactured to the highest quality standards, and are avail-
able with a wide range of end connections compatible with many applications. Some of
the typical applications include: oilfield waterflood, production, well servicing, pipelines,
mining, chemicals, food and beverage industry, and most other liquid applications.

BF series meters are available in the following sizes

All between flange series meters are available for use with 150# - 1500# RF ANSI flanges with
pressure ratings of 275 - 3600 psi.

.75” X 2” 1.5” X 2” 3” X 3” 6” X 6”
1” X 2” 2” X 2” 4” X 4” 8” X 8”

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

4” Long BF Turbine Flow Meters

Electronic Data Devices offers a complete line of between flange turbine flow meters that are
available with ranges from 0.3 GPM to 50 GPM covering a wide range of measurement
applications. Our turbine flow meters are manufactured to the highest quality standards. Some
of the typical applications include: oilfield waterflood, production, well servicing, pipelines,
mining, chemicals, food and beverage industry, and most other liquid applications.

4” long BF meters are available in the sizes below.

The working pressure for the meter is determined by the flanges used. All sizes are compatible
with 150 pound to 1500 pound flanges.

3/8” x 1” x 4” 1/2” x 1” x 4” 3/4” x 1” x 4” 7/8” x 1” x 4” 1” x 1” x 4”

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

Ring Joint
Turbine Flow Meters
Electronic Data Devices offers a line of turbine flow meters that are available with ranges
from 2 GPM to 400 GPM covering a wide range of measurement applications. Our tur-
bine flow meters are manufactured to the highest quality standards. Some of the typical
applications include: oilfield waterflood, production, well servicing, pipelines, mining,
chemicals, food and beverage industry, and most other liquid applications.

Ring joint turbine flow meters are available in the following sizes: 3/4”, 1”, 1 1/2” and
2”. Operating pressure is determined by the rating of the gasket and are available in ei-
ther 1500 series or 2500 series ring joints.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

BF Series Meter Repair Kits

Electronic Data Devices offers a broad line of turbine flow meter repair kits designed for EDD
meters and other popular brands. The kits are available for flow ranges of 0.3 to 5000
GPM. Electronic Data Devices kits fit meter sizes of 3/8” to 10”.

Our repair kits are manufactured to the highest quality standards. The repair kits are manu-
factured of 316SS and CD4MCu for the rotors. Bearings are tungsten carbide and ceramic.
The kits are calibrated in pulses per gallon for each kit. The kits may be used in a wide
range of applications including: oilfield waterflood, production, well servicing, pipelines, min-
ing, chemicals, food and beverage industry and most other liquid applications.

Repeatability: Within + 0.1% of indicated flow throughout the linear flow range.

Accuracy: Within + 1% of the reading Note: 3/8” + 2% of the reading.

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

EDD-600 Totalizer
Electronic Data Devices’ EDD-600 is a self-contained totalizer and flow rate indicator de-
signed to mount directly on the turbine flow meter or remotely mounted with optional
hardware. By using state of the art low power CMOS intergrated circuits and liquid crystal
displays, long battery life is attained.

SPECIFICATIONS
Power 4 C Batteries Battery Life 2 - 4 Years
Flow Rate Digital 6 Digit Flow Rate Units Specified by customer
Totalizer Digital 6 Digit Totalizer Units Specified by customer
Totalizer Reset With optional switch Divisor Capability From 1 - 131071
Accuracy ± 1 Count Mounting Directly on meter
Temperature Range -20° to 155° F Housing Polyester Weatherproof
Input Frequency 0 - 2500 Hz Input Amplitude 20 - 5000 mVpp

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
('''LJLWDO7RWDOL]HU

7KH(''LVDVHOIFRQWDLQHGGLJLWDOWRWDOL]HUGHVLJQHGWRPRXQWGLUHFWO\
RQWKHWXUELQHÀRZPHWHURUUHPRWHO\PRXQWHGZLWKRSWLRQDOKDUGZDUH
7KHWRWDOVDQGÀRZUDWHXQLWVFDQEHVHWWRDQ\LQGXVWU\VWDQGDUGXQLWVRU
EHVHWWRGLIIHUHQWXQLWVIRUHDFKGLVSOD\7KH(''LVHDVLO\UHVHWWDEOH
WR]HURRXWWKHWRWDOXQLWVGLVSOD\HG7KHXQLWLVDYDLODEOHZLWKD1(0$
RU(;3KRXVLQJ,QWULQVLFDOO\VDIH$7(;,(&([)0DQG&6$XQLWVDUH
DYDLODEOH

3RZHU  9'&&FHOO/LWKLXP%DWWHU\
'LVSOD\ /&''LJLWV7RWDOV'LJLWV5DWH
$FFXUDF\ “
7HPSHUDWXUH5DQJH WRR)
,QSXW)UHTXHQF\ +]
%DWWHU\/LIH <HDUV
8QLWV &XVWRPHU6SHFL¿HG
'LYLVRU&DSDELOLW\ 
+RXVLQJ 1(0$RU(;3
2SWLRQV 3XOVH2XWP$RU+DUW
 Electronic Data Devices
Turbine Flow Meters

EDD-340 4-20 mA Converter

The EDD-340 circuit card will accept signal inputs from turbine flow meters or any pulsing
device with acceptable wave forms and signal levels. The card has a 4 - 20 mA output.
The card is 4” x 4” and mounts via 4 standoffs and screws to a backplate. Hookup is via 7
wire compression terminals. The card may be calibrated to any customer specified full scale
output.

Power 24 Vdc or Optional 12 Vdc

Current Pull 50 mA Maximum

Input Frequency 0 - 2500 Hz

Input Amplitude 30 mV - 30 V peak to peak

Accuracy ± 1 Percent

Output 4 - 20 mA into a 250 Ohm Load

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Turbine Flow Meters

EDD-530 Pulse Output Card

The EDD-530 card will accept signal inputs from turbine flow meters or any pulsing device
with acceptable wave forms and signal levels. The output is a dry contact closure or an
optional voltage output. The card is 4” x 4” and mounts via 4 standoffs and screws to a
backplate. Hookup is via 6 wire compression terminals. The card may be calibrated in
any customer specified engineering units up to a maximum divisor of 16383.
Power 12 or 24 Vdc (must spec.)
Divisor Capability 1—16383
Pulse Output Units Specified by customer
Accuracy ± 1 Count
Temperature Range -20° F - 140° F
Input Frequency 0 - 2500 Hz
Input Amplitude 30 mV - 30 V peak to peak
Pulse Output Duration 150 ms or customer specified Note: Circuit Current Pull
12 Vdc - 30mA
Voltage Output Option Discuss with Factory 24 Vdc - 35 mA

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electonic Data Devices
Odessa, Texas USA PREAMPLIFIER
432-366-8699
sales@eddevices.com MAG TYPE
STANDARD AND MICROPOWER

PRODUCT DESCRIPTION
____ PUCK (for ELBY 1/2, 3/4 - Y2)
EDD's mag-preamps are designed to convert low level
sinusoidal signals into stable square wave pulses. They can J unction B ox for 4023
be used with all magnetic VR type pickups, allowing for
greater pickup to target gaps and longer signal transmission
distance. The pucks are built to fit compact “ELBY” and
“Y” type explosion-proof enclosures, refer to bulletin 4001.
For Intrinsically Safe certified see brochure: IS4022, 29
Other J unction B oxes and adapter hardware,
* MICROPOWER versions are available in the ____ and E xplos ion proof U L & CS A cert
____ models for ultra low current draw, ideal for battery
applications.
SPECIFICATIONS
Vs, Supply Voltage: 7.5 (12)to 30 Vdc regulated
3.6 Vdc min., unregulated
* MICROPOWER: 2 to 6 Vdc ____ PUCK (for Y1)
Is, Supply Current: [ 2 mA @ 5 Vdc
[ 4 mA @ 12 Vdc
[10 mA @ 24 Vdc
[20 mA @ 30 Vdc ( OC ) 1 2 3 4 5
*MICROPOWER: [ 0.06 mA
[ 5 mA (Current Loop, 4029)

Vo, Signal Out: 0 - 10 V NPN

@ £ 20m A s ink 0 - 5V NPN
0 – Vs NPN
0 – Vs, NPN, OC, (Open Collector)
0 – Vs, PNP, OC, 50 mA Sourcing
____ only: 4 to 20 mA current sink:
62 mA, 4 to 40 V supply, see page 2 ____ TUBULAR
for wiring diagram & R Load spec.
Input Sensitivity: 30, 12 or 5 mVpp
* MICROPOWER: 12 to 40 mV
C
Frequency Range: 3 Hz to 10 kHz at specified sensitivity
[ 40 kHz at increased signal level,
varies with target size, distance and _B MS3
pickup sensitivity. (Option: [ 100 kHz)
*MICROPOWER: [ 1 Hz to 30 kHz
+
A
Rise/Fall Time (N.L.):. 04 / .18 µs (Nom.)
Distance: 500 ft. max. pickup to preamp
T em perature R ange: -40 o to 221 o F ( -40 o to 105 8 C)
Compliance: CE: EN55011, EN50022-2
____ PUCK (for ELBY 1/2, 3/4 - Y2)
TERMINAL/PIN CONNECTIONS
Digital Opto-Isolated Current Loop
____ & ____: 1. Input Vdc 4. Mag Pickup
2. Common 5. Mag Pickup
3. Pulse out (+)
on ____: 6. Pulse out (-)

____: MS3106A-10SL-3S A: Input Vdc

B: Common
C: Pulse out
OPTIONS: Please contact sales.
For junction boxes & adapters see spec. 4001
For connector cable assemblies, please see spec. 3000
ORDER INFORMATION
____ - x x MAG PREAMP, PUCK ELBY TYPE Junction Box for ____
Output 1 0 - 10V 90010-01 Y1 (1/2-14 NPT)
Signal 2 0 - 5V (TTL Compatible)
5 Selectable ( OC; 0-5V: 0-10V ) Junction Box for ____ & ____
6 0 - Vs, PNP, OC, 50mA (100 mA max) Sourcing 90012-01 ELBY (1/2-14 NPT)
Input 0 30 mVpp
Sensitivity 1 12 mVpp Other Junction Boxes and adapter hardware,
Explosion proof UL & CSA certified, see spec. 4001
____ - x x MAG. PREAMP, PUCK Y1 TYPE
____ - x x MAG. PREAMP, TUBULAR IN-LINE TYPE
Male Threaded & Female Threaded Connectors
____M - x x MAG. PREAMP, TUBULAR IN-LINE TYPE
Male Threaded Connectors, both ends
1 0 - 10V, NPN
Output
Signal 2 0 - 5V, NPN
3 0 - Vs, NPN *
0 - Vs, OC, NPN (Open Collector)*
*OPTIONS AVAILABLE IN MICROPOWER VERSION
4

Input 0 30 mVpp
Sensitivity
1 12 mVpp
2 5 mVpp
4 MICROPOWER 12 to 40 mVpp ONLY*

____ - x x MAG PREAMP,

DIGITAL OPTO-ISOLATED CURRENT LOOP
PUCK ELBY TYPE
Current 1 4 - 20 mA
Sink 2 10 - 50 mA

Input 0 30 mVpp
Sensitivity 1 12 mVpp

WIRING DIAGRAM,
OPTION A AMPLIFIER
Vs -4 POWER SUPPLY
R Load [
.02A
Vs ∴ 12 V [ 400 Ω
24 V [ 1000 Ω

DIGITAL OPTO-ISOLATED
CURRENT LOOP R Load (1/2 W 5%)

WIRING DIAGRAM,
OPTION B AMPLIFIER
POWER SUPPLY

Vs -4
R Load [
.02A
Vs ∴ 12 V [ 400 Ω
24 V [ 1000 Ω

DIGITAL OPTO-ISOLATED R Load (1/2 W 5%)

CURRENT LOOP
4.0420
 EDD FREQUENCY-CURRENT CONVERTER 4.0420
Installatinos must meet the requirements of intrinsically safe systems
for hazardous (classified) locations and must follow details specified
in FMRC engineering control drawing #85049
 Electronic Data Devices
Turbine Flow Meters

4.303 MAGNETIC PICKUP

Electronic Data Devices’ magnetic pickups are manufactured to cover a wide range of
metering applications, including our meters and most others popular brands of meters.

SPECIFICATIONS

DC Coil Resistance 1450 ohms Output Volts 2.5Vpp (turbine meters)

Inductance 800 mh Pole Piece Extended
Magnetization 900 Gauss Construction 303/304 S>S> solid epoxy
Temperature Range -150° to +250°F Connection 2 pins gold plated
Overall length 2.25” Mating Connector MS 3106A-10SL-4S
Thread Size 5/8 X 18 Thread Length 1.13”

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Odessa, Texas USA 4.303
432-366-8699
sales@eddevices.com Digital Magnetic Pick-Up
5/8 - 18 UNF
Product Description

Electronic Data Devices’ Digital 2 PIN magnetic pick-ups feature

high output voltage and great configuration diversity to meet a
wide range of applications.

A sanitary version to NEMA 6, IP65 & IP67 is also offered.

All Models are also available with an optional temperature

probe.

Specifications

DC-C
Coil: Resistance/Inductance/Output Voltage
1500 Ohms/ 800 mH/ 240 Vpp

Magnetization: 950 GAUSS

o o o o
Temperature Range: -100 to 250 F (-73 to 120 C)

Pole Piece: Extended Pole, 0.106 dia. x 0.020 L

Construction: 303/304 Stainless Steel

Solid Epoxy Encapsulation
All standard connectors have gold
plated pins.

Application: For gear pitch range of 24 DP or

coarser depending on pole piece.

CE-C
Compliance: EN55011, EN50022-2

Options: For different lenght, material of con

struction, configuration, special pole
piece type, thread size, hermetically
sealed, precision custom magnetiza
tion, intergal temperature sensor, con
nector and/or cable termination,
please contact factory.

PIN Out

A +Voltage
B -Ground

Connector Type Pick-up Part Number: 4.303

WIre Lead Pick-up Part Number: 4.303L
Connector Part Number: MS3106-10SL-4S
Page 1 of 1
 Electronic Data Devices
Odessa, Texas USA 4.304
432-366-8699
sales@eddevices.com Digital Magnetic Pick-Up
5/8 - 18 UNF
Product Description

Electronic Data Devices’ Digital 2 PIN magnetic pick-ups feature

high output voltage and great configuration diversity to meet a
wide range of applications.

A sanitary version to NEMA 6, IP65 & IP67 is also offered.

All Models are also available with an optional temperature

probe.

Specifications

DC-C
Coil: Resistance/Inductance/Output Voltage
1500 Ohms/ 800 mH/ 240 Vpp

Magnetization: 950 GAUSS

o o o o
Temperature Range: -100 to 250 F (-73 to 120 C)

Pole Piece: Extended Pole, 0.106 dia. x 0.020 L

Construction: 303/304 Stainless Steel

Solid Epoxy Encapsulation
All standard connectors have gold
plated pins.

Application: For gear pitch range of 24 DP or

coarser depending on pole piece.

CE-C
Compliance: EN55011, EN50022-2

Options: For different lenght, material of con

struction, configuration, special pole
piece type, thread size, hermetically
sealed, precision custom magnetiza
tion, intergal temperature sensor, con
nector and/or cable termination,
please contact factory.

PIN Out

A +Voltage
B -Ground

Connector Type Pick-up Part Number: 4.304

WIre Lead Pick-up Part Number: 4.304L
Connector Part Number: MS3106-10SL-4S
Page 1 of 1
 Electronic Data Devices
Turbine Flow Meters

4.5015U MAGNETIC PICKUP

Electronic Data Devices’ magnetic pickups are manufactured to cover a wide range of
metering applications, including our meters and most others popular brands of meters.

SPECIFICATIONS

Supply Voltage 7.5 to 30 Vdc Signal Output 0 - 10 V

Frequency Range 3 - 10 kHz Pole Piece Extended
Magnetization 900 Gauss Input Sensitivity 30 mVpp
Temperature Range -40° to +250°F Connection 3 pins gold plated
Overall length 3.0” Mating Connector MS 3106A-10SL-3S
Thread Size 5/8 X 18 UNF Thread Length 1.75”

P.O. Box 12128 Phone Fax Email Website

Odessa, Texas 79768 432-366-8699 432-366-1106 rkw@eddevices.com www.eddevices.com
USA
 Electronic Data Devices
Odessa, Texas USA 4.5015U
432-366-8699
sales@eddevices.com Digital Magnetic Pick-Up
5/8 x 18 UNF
Product Description

Electronic Data Devices’ Digital 3 PIN magnetic pick-up

produces a digital frequency output directly proportional to
speed. The internal amplifier provides for constant pulse
shaping, signal amplitude, logic-level output, improved
signal-to-noise ratio, usable at lower RPM’s and greater air
gap between the sensor and the actuator.

MICROPOWER wersions are available for ultra low current

draw, ideal for battery appliactions.

A sanitary version to NEMA 6, IP65 & IP67 is also offered.

All Models are also available with an optional temperature

probe.

Specifications

Vs, Supply Voltage: 7.5 (12) to 30 Vdc regulated

3.6 Vdc min., unregulated
MICROPOWER: 2 to 6 Vdc

Is, Supply Current: < 2 mA @ 5 Vdc

<4 mA @ 12 Vdc
<10 mA @ 24 Vdc
<20 mA @ 30 Vdc (OC)
MICROPOWER: < 0.06 mA

Vo, Signal Out: 0 - 10 V, NPN

@ < 20 mA sink 0 - 5 V, NPN
0 - Vs, NPN
0 - Vs, NPN, OC (Open Collector)

Input Sensitivity: 30, 12 or 5 mVpp

MICROPOWER: 12 - 40 mV

Frequency Range: < 3 Hz to 10 kHz

< 40 kHz at increased signal level,
varies with target size, distance and
pick-up sensitivity.
(Option: <100 kHz)
MICROPOWER: <1 Hz to 30 kHz

Rise/Fall Time: 0.04 / 0.16 µs

PIN Out
o o o o
Temperature Range: -40 to 248 oF (-40 to
o
120 C)
(Option: -45 to 140 C)
A +Voltage
Magetization: Standard: > 900 GAUSS B -Ground
Low Mag: 250 GAUSS, typ. C Signal Output Square Wave
Sensor Body: 303 Stainless Steel

Connector Type Pick-up Part Number: 4.5015U

WIre Lead Pick-up Part Number: 4.5015L
Connector Part Number: MS3106A-10SL-3S
Page 1 of 1
 Electronic Data Devices
Odessa, Texas USA 4.5024
432-366-8699
sales@eddevices.com Digital Magnetic Pick-Up
11/16 - 24 UNEF-2A
Product Description

Electronic Data Devices’ Digital 3 PIN magnetic pick-up

produces a digital frequency output directly proportional to
speed. The internal amplifier provides for constant pulse
shaping, signal amplitude, logic-level output, improved
signal-to-noise ratio, usable at lower RPM’s and greater air
gap between the sensor and the actuator.

MICROPOWER wersions are available for ultra low current

draw, ideal for battery appliactions.

A sanitary version to NEMA 6, IP65 & IP67 is also offered.

All Models are also available with an optional temperature

probe.

Specifications

Vs, Supply Voltage: 7.5 (12) to 30 Vdc regulated

3.6 Vdc min., unregulated
MICROPOWER: 2 to 6 Vdc

Is, Supply Current: < 2 mA @ 5 Vdc

<4 mA @ 12 Vdc
<10 mA @ 24 Vdc
<20 mA @ 30 Vdc (OC)
MICROPOWER: < 0.06 mA

Vo, Signal Out: 0 - 10 V, NPN

@ < 20 mA sink 0 - 5 V, NPN
0 - Vs, NPN
0 - Vs, NPN, OC (Open Collector)

Input Sensitivity: 30, 12 or 5 mVpp

MICROPOWER: 12 - 40 mV

Frequency Range: < 3 Hz to 10 kHz

< 40 kHz at increased signal level,
varies with target size, distance and
pick-up sensitivity.
(Option: <100 kHz)
MICROPOWER: <1 Hz to 30 kHz

Rise/Fall Time: 0.04 / 0.16 µs

PIN Out
o o o o
Temperature Range: -40 to 257 oF (-40 to
o
125 C)
(Option: -45 to 140 C)
A +Voltage
Magetization: Standard: > 900 GAUSS B -Ground
Low Mag: 250 GAUSS, typ. C Signal Output Square Wave
Sensor Body: 303 Stainless Steel

Connector Type Pick-up Part Number: 4.5024

WIre Lead Pick-up Part Number: 4.5024L
Connector Part Number: MS3106A-10SL-3S
Page 1 of 1
 Electronic Data Devices
Odessa, Texas USA 4.5050
432-366-8699
sales@eddevices.com Digital Magnetic Pick-Up
5/8 - 18 UNF
Product Description

Electronic Data Devices’ Digital 2 PIN magnetic pick-ups feature

high output voltage and great configuration diversity to meet a
wide range of applications.

A sanitary version to NEMA 6, IP65 & IP67 is also offered.

All Models are also available with an optional temperature

probe.

Specifications

DC-C
Coil: Resistance/Inductance/Output Voltage
3000 Ohms/ 1500 mH/ 290 Vpp

Magnetization: 600 GAUSS

o o o o
Temperature Range: -150 to 330 F (-101 to 165 C)

Pole Piece: Extended Pole, 0.106 dia. x 0.020 L

Construction: 303/304 Stainless Steel

Solid Epoxy Encapsulation
All standard connectors have gold
plated pins.

Application: For gear pitch range of 24 DP or

coarser depending on pole piece.

CE-C
Compliance: EN55011, EN50022-2

Options: For different lenght, material of con

struction, configuration, special pole
piece type, thread size, hermetically
sealed, precision custom magnetiza
tion, intergal temperature sensor, con
nector and/or cable termination,
please contact factory.

PIN Out

A +Voltage
B -Ground

Connector Type Pick-up Part Number: 4.5050

WIre Lead Pick-up Part Number: 4.5050L
Connector Part Number: MS3106-10SL-4S
Page 1 of 1
 Electronic Data Devices
Odessa, Texas USA 4.302T800
432-366-8699
sales@eddevices.com Magnetic Speed Sensor
High Temperature
Product Description

Electronic Data Devices’ high temperature

magnetic pick-ups are suited for adverse
temperature conditions.

Specifications

DC-C
Coil: Resistance/Inductance:
As tabulated in product
details below.

Magnetization:
Standard: 900 GAUSS, typ.
Low Mag: 300 GAUSS, typ.

Temperature Range:
o o
8HT: -450 to +850 F
o o
(-270 to +458 C)

Pole Piece:
Flush and extended are available.

Construction:
303/304 Stainless Steel, Blindshell CF
(closed face) design.
Solid Ceramic Encapsulation
Mica-Glass Insulated Lead Wires, 22AWG

Application:
For gear pitch range of 24 DP or coarser
depending on pole piece.
Options

For different length, material construction, configuration,

special pole piece, thread size, hermetically sealed, precision
custom magnetization, please contact factory.

Part Number 4.302T800, R or H

Lead Wires L 36”
Thread 3/4 - 20 UNEF
Thread Length (A) 1.9” (46 mm)
Shell Length (L) 3.12” (79 mm)
Coil Resistance 160 Ohms
(Inductance) (140 mH)
Pole Diameter 0.106”
Pole Length 0.020”

Page 1 of 1