Scribd
Upload
373 views4 pages

Technical Specification

This document provides specifications for an elevator including its type, capacity, speed, dimensions, finishes, and functions. The elevator has a capacity of 5000kg, travels at 0.5m/s between two floors, and is powered by a three phase 400V power supply. Interior finishes include steel walls and flooring. Standard functions include full collective operation, terminal floor protection, and overload protection.

Uploaded by

Ck Wong
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
373 views4 pages

Technical Specification

This document provides specifications for an elevator including its type, capacity, speed, dimensions, finishes, and functions. The elevator has a capacity of 5000kg, travels at 0.5m/s between two floors, and is powered by a three phase 400V power supply. Interior finishes include steel walls and flooring. Standard functions include full collective operation, terminal floor protection, and overload protection.

Uploaded by

Ck Wong
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

BASIC INFORMATION CL

Main Feature

1 Elevator Type UN-F5000

2 Quantity 1

3 Capacity 5000kg

4 Speed 0.5m/s

5 Floors/Stops/Openings 2/2/2 (Floor mark: G, 1)

6 Travel Height 9,000mm

8 Standard Code GB

8 Machine Room Location Top of Hoistway

9 Control System VVVF

10 Control Type Simplex Control

11 Motor Type Gearless

12 Power Supply Three Phase 400V/50Hz, Single Phase 240V/50Hz

13 Hoistway Structure Concrete

14 Door Operator Permanent magnet frequency conversion

15 Door Arrangement - Type 4P-CO (Double opening, front: G, rear: 1)

Dimensions

1 Hoistway Size (W*D) 3950mm * 3900mm

2 Car Outer Size (W*D*H) 2500mm * 3600mm * 2500mm

3 Opening Size (W*H) 2400mm * 2400mm

4 Overhead 7000mm

5 Pit 1500mm
Car Interior Finishes

1 Cabin Model U-CR501

2 Cabin Wall (Side & Rear) Power-painting Steel

3 Cabin Wall (Front) Power-painting Steel

4 Cabin Door Power-painting Steel

5 Ceiling Std. of U-CR501

6 Floor Steel Chequer Plate

7 Handrails /

Landing Doors Finishes

Main Floor: Power-painting Steel (EI120)


1 Landing Doors
Typical Floors: Power-painting Steel (EI120)

Main Floor: Power-painting Steel


2 Narrow Jambs
Typical Floors: Power-painting Steel

Main Floor: Without


3 Wide Jambs
Typical Floors: Without

Human Interface

1 COP Qty. 1

2 COP Type U-CF500

3 COP Panel Hairline St. St.

4 COP Display 6.4’’ STN-LCD

5 COP Buttons BS34C

6 Hall Call Type U-ZW500

7 Hall Call Display 4.3’’ STN-LCD

8 Hall Call Buttons BS34C


ELEVATOR FUNCTIONS CL

Standard Functions
1 Full Collective Operation
2 Floor of Lobby
3 Infrared Curtain Door Protection
4 Top of Car Inspection
5 Terminal Floor Protection
6 Over-load Protection
7 Door Open / Close Button
8 Independent Control of Landing Door & Car Door
9 Hall / Car Direction Indication
10 Hall/Car Position Indicator
11 Four Sides Interphone (R＞30M, ICU-5)
12 Emergency Light
13 Alarm Bell
14 Full-load Non Stop
15 Delayed Car Protection
16 Correcting Run
17 Driver Overheat Protection
18 Calls in Opposite Direction Auto-clear
19 Parking Operation
20 Start Equalize
21 Fault Self-diagnosis
22 Shaft Position Self-learning
23 Brake Feedback Inspection
24 Contactor Feedback Inspection
25 Rated Speed Feedback Inspection
26 Cancel Error Calls
27 Door Hold Cancel
28 Parking
Optional Functions (Included)
1 Malaysia Std.
2
3

You might also like