EP 300
Epoxy Bonding Agent
Features
Excellent bond strength
Non-Shrink
Forms a structural bond between new and old concrete
Can be applied to damp surfaces
Compatible with fresh cement or concrete products
Excellent adhesion to most substrates
ARDEX ENDURA (INDIA) PRIVATE LIMITED
Corporate Office & Regd. Office: 73/1B,
Byregowda Indl. Estate, Srigandhanagar,
Hegganahalli, Peenya 2nd Stage,
Bangalore - 560 091, Karnataka, INDIA.
Tel: +91-80-2836 1672 / 2836 1673
Fax: +91-80-2836 2078
E-mail: customercare@ardexendura.com
EP 300
Epoxy Bonding Agent
DESCRIPTION PROPERTIES Observe personal hygiene, particularly
EP 300 is an un-pigmented two component, The values shown are typical of results washing the hands after work has been
polyamide epoxy bonding agent. It is obtained in the laboratory at 27 ± 1ºC. completed or at any interruption whilst work
specifically designed for bonding new render Actual performance values obtained on site is in progress. Care should be taken when
or concrete to aged or old concrete may vary from those quoted. removing gloves to avoid contaminating the
substrates. It acts as a high strength insides. In case of accidents seek medical
bonding bridge between old and new PHYSICAL PROPERTIES advice.
concrete. EP 300 @ 27 ± 1ºC
EP 300 is a good bonding agent for tiles, DISPOSAL/SPILLAGE
Appearance Off white colour,
bricks, concrete blocks, repairing potholes Spillage of any of the accelerating admixer
with brushable
and spalled concrete, etc. product should be removed with plenty of
consistency
water. Disposal of such product or empty
SURFACE PREPARATION Pot life 4 - 5 hours packaging should be in accordance with
The surface to be treated must be clean and local waste disposal authority regulations.
structurally sound, free from oil, grease, Mixed density 1.35 - 1.40 g/cc
laitance, dust and other barrier materials. Initial cure 48 hours For further information please refer to the
All previous coatings should be removed. Product Safety Data Sheet.
Full cure 7 days
Use a suitable degreser to remove polish, Time between the coats 24 hours CONDITIONS OF SALE
wax, grease, oil and similar contamination 2 Sold subject to the Company's conditions
substances prior to the EP 300. Bond strength > 2.0 N/mm
of sale which are available on request.
After 1 day
MIXING & APPLICATION Compressive strength 76.0 N/mm2 NOTE
Individual contents of EP 300 should be After 7 days The information supplied in this datasheet is
thoroughly stirred before being mixed BS 6319-Part-2 based upon extensive experience and is
together. The entire content of the Part A given in good faith in order to help you. Our
should be poured into a larger mixing vessel Flexural strength 50.0 N/mm2 Company policy is one of continuous
to incorporate the Part B. Finally the part B BS 6319-Part-3 Research and Development; we therefore
is added to the same vessel. Mix all the two 2 reserve the right to update this information
Tensile strength > 13.0 N/mm
materials with spiral mixing paddle in a slow at any time without prior notice. We also
BS 6319-Part-7
speed drill, continue until a consistant guarantee the consistent high quality of our
2
homogenous mix is achieved. One or more Shear strength Test > 5.0 N/mm products; however as we have no control
packs can be mixed simultaneously to BS 6319-Part-4 over site conditions or the execution of the
ensure a quick rate of installation. work, we accept no liability for any loss or
COVERAGE ESTIMATES damage which may arise as a result thereof.
The mixed material should be applied to the Pack Size Coverage
prepared surface without delay using a
brush. Only apply the Bonding Bridge to an 5kg Approximately 10m²/kit
area to which the new render or concrete Part A 4kg
can be placed while the bonding bridge Part B 1kg
remains tacky state. Immediately following
application of the EP 300, place the new NOTE: The coverage figure is based on a flat
render or concrete and finish as required. level surface, additional material should be
Repeat the process until the full area to be allowed for where the surface is rough or
treated is complete. uneven.
LIMITATIONS STORAGE AND SHELF LIFE
EP 300 should be applied whilst the surface EP 300 has a shelf life of 12 months if kept
temperature is between 10º - 35ºC. The in a dry, store between 5ºC and 30ºC in the
product will cease to cure below 10ºC, but original unopened containers. The product
will recommence curing when the should be protected from frost, away from
temperature rises above 10ºC. Curing time direct sunlight and sources of heat. BRANCHES
Ÿ AHMEDABAD 079 26425310 Ÿ KOLKATA 033 23452581
will also be adversely affected in situations Ÿ AURANGABAD 9881249293 Ÿ LUCKNOW 0522 4043251
PRECAUTIONS
where relative humidity is > 85%. Ÿ BANGALORE 080 22230138 Ÿ LUDHIANA 0161 2532170
In case of contact with the eyes, rinse Ÿ BANGALORE 080 65681338 Ÿ MANGALORE 0824 2442176
Good ventilation should be provided during Ÿ BHUBANESHWAR 9937091799 Ÿ MUMBAI 022 65133299
immediately with plenty of water and seek
curing cycle. Ÿ CALICUT 0495 2333065 Ÿ PUNE 020 64781879
medical advice and after contact with the Ÿ CHENNAI 044 24748673 Ÿ RAIPUR 0771 6539055
Ÿ DELHI 011 32092369 Ÿ RAILA 9509764756
skin wash immediately with plenty of soap
CLEANING Ÿ ERNAKULAM 0484 2341044 Ÿ RAJKOT 9328286287
EP 300 can be removed from tools and and water (do not use solvents). Prolonged Ÿ GOA 0832 2750992 Ÿ SALEM 0427 2211454
Ÿ GUWAHATI 9864277661 Ÿ TRICHY 0431 6454649
equipment by using ARDEX ENDURA RTC 100 contact with the skin should be avoided, Ÿ HUBLI 0836 2236919 Ÿ TRIVANDRUM 0471 2558648
immediately after use. Any hardened material will especially where the user has an allergic Ÿ HYDERABAD 040 27550293 Ÿ VIJAYAWADA 0866 3254587
06/12
Ÿ INDORE 0731 4021148 Ÿ VISAKAPATNAM 0891 6469499
need to be removed mechanically. reaction to epoxide materials. Always wear Ÿ JAIPUR 0141 2392993
gloves and eye/face protection is necessary.
