. . ..

,
( ~

..

• •

• TM

TAITO G NET

Instruction Manual
ACaution
- To-use this machine safely and correctly, read this manual carefully and make
sure·you fully understand the contents before using the machine.

- After reading this manual, keep it in a designated place so that it can be

referenced by others anytime.

TAITO CORPORATION®
G2500879A
- .

•
 • •
CORRECTlON
T here are two e rrors in the In struction M anual. P lease refer to the followings.

P -22 _ After installing the G card (game) correctly. turn ON the power

[X] switch of the enclosure.

(If the G card is not installed correctly, start the installation again
from the beginning.)

_ After installing the G card (game) correct ly. turn ON the power
switch of the enclosure.
(I f the G card is not installed correctly, start the install ation again
from the beginning.)

[0]
-In the event the "G card" is inserted improperly, a system error
occu rs and game can not be played. Make sure the NG card- is
inserted into the game(mother) boa rd properly.
(Error messages- Page28)
•
P -28 Screen display Contents Treatment
• This error occurs when il1akes
COIN ERROR one second or longer for the co in Read the instruction manual 01
inserted into the enclosure to pass
the enclosure.
through the micro-switch inside
the rejedar.

SERVICE SW ERROR • The service switch inside the

er.closure is lumed ON by being

[X] caughl due 10 damage.

• The harness connected to the

Read the instruction manual 01
the enclosure.

•
service switch is ShOrted.

nLT Read the instruction manual 01

• The lilt sensor is functioning.
the enclosure.

Screen display Conlel'lta Treatment

• This error occurs when jtlakes
COIN ERROR one second or longer for Ihe coin Read the instruction manual 01
inserted Into the enclosure 10 pass
the enclosure.
Ihrough Ihe mjcro-sw~ch Inside
the rejecter

SERVICE SW ERROR • The service switctllnside the

enclosure is tumed ON by being
caught due to damage. Read the instruction manual of

[0] • The harness connected to the

service switch is shoned.
the enclosure.

TILT Read the instruction manual of

• The tilt sensor is lunctioning.
the enclosure

• The game PC board caonoI read • Check ~ the G card (game) is

SYSTEM ERROR the program trom the G card inserted securely.
(game). (tnstaltation - Page 22)
 P -29 •
T-. POss'ble cause Treatment
· The game PC board cannot read
the program from the G card · Check jf the G card (game) is inserted s9rurely.
(game). (Installation - Page 22)

• The G can! is bfoken due to · Aaplace the G card.

The game PC board shock or statiC electricity.
repealS resetting.
· The power voltage is not • Adjust the switching power voltage.
appropriate. (lflStaliatioo - Page 23)

· The edge connector is badly · Remove dirt on the edge connec10r lennioal side

""""""'.
· The hamass is diSalnnectad
using a dean and soft doth.

· Replace the harness .

or shorted.
· The sound level setting on the main · Tum Ihe sound level adjusting dial clockwise to
The sound level PC board is saito lower volume , lull vojume , (Nama of each parts- Page 11 )
is low .
• The sound level on the enclosure · Tum the sound level adjusting dial inside the

[X ]
side is S9I to lower YOIume. enclosure.
· The power vonage Is I10l • Adjust the switching power voltage .
appropriate. (Installation - Page 23)
The system · The enclosure power is comeded
sometimes rasels by the same power line to the
or the screen stops · Change lhe power supply 10 the enclosure.
vending machine. fflfrigeralOf,
displayin g. or air conditioner.
· The game PC board is broken
· Replace Ihe game PC board.
due 10 shock or stalic electricity.
· The power is not supplied to the · Insert the pllJg alter turning OFF the power switch.
power pk.tg of the enclosure. Then, tum ON the power switch again.
• The JAMMA harness is not · Insert the JAMMA harness securely after checking

•
cooneded correctly. the comeCIor direction.
· The JAMMA harness is
· Replace the JAMMA harness.
di sconnected or shorted.
· The harness speCifications are
NO operation is · Replace it with lhe correct harness.
not appropriate.
pertOlTrled.
, The power voltage Is root .14ost the switching power voltage.
appropriate. (Instanation - Page 23)
· The game PC board is
broken due to shock or static • Replace'the game PC board.
ejectricit~.

, Replace the fuse after d1ei::kng if the harness

· The ruse is blown off. shorts with the game PC board Of other
components.

T",""" Possible cause Treatment

· The power voltage Is not · Adjust the switching power voltage.
appropriate. (Instaltatior"l - Page 23)
The game PC board · The edge COlYlector Is badly • Remove dirt on the edge COMeclor lenninat side
repeats resetting . conl"lOCled. using a dean and soft dolh.
· The harness is dscOMeCled
, Replace the harness.
or shorIed.

•
• The soond level setting on the main · Tum the sound levej adjus~ng dial dockwise!o
The soUl"ld level PC board is set to lower volume. 1wlt IIOlume. (Name 01 each parts- Pege II)
is low.
· The soond level on the enclosure · Tum the sound level adjusting dial imide the
side is set to lower volume. enclosure.
· The power voltage is not , Adjust the switching power voltage.
IlPClnJprlate. (Installation - Page 23)
The s~stem · The enclosure power is connllC1ed

[0 ] sometimes resets
or the screen SlopS
displaying.
by the same power line 10 lhe
vending machine, re1rigerator,
Of air cooditioner.
· Change the power supply to the enclosure.

, The game PC board is bfl)ken

due 10 shock or SIalic electricity. • Replace the game PC board.

· The power is nOl supplied to the · Inserl the plug alter turning OFF the power switch.
power plug 01 the endosure. Then, tum ON the power switch again.
· The JAMMA hamess is not · Insert the JAMMA harness se<:urety after checking
connected COlTectly. the connector direction.

• The JAMMA halTless is

, Replace the JAMMA harness.
disconnected Of Shorted.
· The harness spec~ications are
No operation is · Replace it with Ihe correc1 harness.
not appropriate.
pertormed.
• The power voltage Is not • Acijust the switching power voltage.
appropriate. (Installalion - Page 23)
· The game PC board is
broken due to shock or Sialic · Replace the game PC board.
electricity.
, Replace the lusa alter ched<ing ~ the harness
• The fuse is blown ott. Shorts w ith the game PC board Of oIher
components.
 face

Thank you very much for purchasing ou r "TA ITO G NET" game machine .

Purpose of this instruction manual:

This manual includes handling methods and precautions for using the "TAITO G NEr (hereafter referred to as
"mother PC boa rd ") correctly. For details about the "TAl TO G CARD" (hereafter referred to as "G card"), see
the separated game instruction manual for the "TAITO G CARD."
(Thi s product does nol include the G card (game) and its instruction manuaL)
Read this manual carefu lly and keep it in a safe place so that it ca n be used as a reference al any time. If you
loose thi s manual, contact our dealers to obtain a new o ne .

For contact:
Fo r inquiries about problems, contact the dealer whe re yo u purchased you r "T A ITO G NET: aft er c he cking the
model name desc ribed on the product.

Model name

Contents of this instruction manual:

The contents of this manual are as follows:
• Introduction :Collection of the safety information which are described in each chapter of this manual
• Chapter 1 : In stallation
• Chapter 2 :Ope ration checks
• Chap ter 3 . 5 : Maintenance

1
 ..
ortant information for safe

This manual use th e fo ll owing definitio ns to explain the safe l y inf o rmat ion. Read them ca refu lly and b e su re to
follow all cau tions and warnings.

Definition of personnel in this manual:

We use the following definitions for game -machine personnel in th is manual:

• Management staff
S tall who operate and maintain amuseme nt sites o r shops unde r the supervision of the owners of
amusement game machine.

• Arcade maintenance man

Persons who have exper i ences in arcade-game mach i ne main tenance and regu lar ly carry oul the
insta llation . assembly and maintenance chec ks of games, and who r eplace paris and consumable items
under supervision of the game owne rs or the shop management staff.

• Engineer
Persons who work for amusement game machine manu f acturers and are responsible for the design,
product inspection, and maintenance of amusement game machi nes, or those who have knowledge of
electrical, electronic , and mechanical engin eering that is equiva lent to the knowledge of an enginee ring
high school graduate , and who regularly main ta in and repai r amuseme nt game machines.

• Player .
Persons who play games at facilities and shops whe re arcade am'u sement game machines are installed.

• Gallery
Persons who look at games at facilities and shops where arcade amusement game machines are installed.

Explanation of the safety symbols:

In this manual, deg rees of dange r and damage cased by mishandling are classi fied by use of the folio i
labels and symbols.

Indicates a situation that may lead to death or serious injury if not

handled properly.

Indicates a situation that may lead to personal injury, or damage to

the parts or the machine if not handled properly.

Indicates important parts of the procedures that should be

followed carefully. Indicates possible situations thaI may occur
when working with this machine.

[. ____0______. .) Indicales prohibilions ( "Oon'IS" ).

2
,. •

Cautions for safety

• Product overview

AcAuTION
• Be care ful not to injure you rself on the soldered side of the
game (m other) PC board when working with it.

• Make sure to turn OFF the powe r switch before pulling out or
putting in the connector or the G card from the game (mother)
PC board , or changing the DIP switches settings.

• The game (mother) PC board may be damaged by a static

electricity, since it consists of preCision parts.

•
• 00 nol drop the game (mother) PC board, give it a slrong
shock on, or touch il with wei hands .
If may cause a problem or accident.

• Make sure to tum OFF the power switch before changing the
sound between stereophonic and monophonic.

• If you adjust the output voltage of the switching regulator

higher than the standard value, the game (mother) PC board
or the G card may be damaged.

• Do not measure pOints using a tester, even if the game

(mother) PC board is obviously defective.

• Before inserting a G card, make su re to turn O FF the power

switch Ii rst, and then insert it into the G card insert slot slow ly
and securely while making sure of the direction . Otherwise, it
may cause a problem or accident.

• Do not make the G card insert slot we t or dirty. It may cause a

problem or accident.

• Never insert cards other than the G card into the G card

•
insert sloUt may cause a problem or accident.

• Do not d rop the G card,give it a strong shock on, or touch or

disassemble it with wet hands. It may cause a problem or
accident.

3
 ,,

• Installation

ACAUTION
• Make sure to follow the installation requirements.

• Turn OFF the power switch althe game machine before

installation.

• Before removing the game (mother) PC board from the game

machine, turn OFF the pawe', switch.

• Be careful not to injure yourself on the soldered side of the

game (mother) PC board during installation.

• Make sure to turn OFF the power switch before pulling out or
putting in the connector or the G card from the game (mother)

•
PC board, or changing the DIP switches settings.

• The game (mother) PC board may be damaged by a stal ic

electricity, since it consists of precision parts.

• Do not drop the game (mother) PC board, give it a strong

shock on, or touch it with wet hands. If may cause a problem
or accident.

• Before inserting a G card, make sure to turn OFF the power

switch first, and then insert It into the G card insert slot slowly
and securely while making sure of the direction. Otherwise, it
may cause a problem or accident. Inserting it forcibly may
cause a problem.

• Do not make the G card insert slot wet or dirty. It may cause a
problem or accident.

• Make sure to adjust the voltage.

• If you adjust the output voltage o f the switching regulator

higher than the standard value, the game (mother) PC board
or the G card may be damaged.

• Never insert cards other than the G card into the G card
insert slot.it may cause a problem or accident.

• Do not drop the G card,give it a strong shock on, or touch or

disassemble it with wet hands. It may cause a problem or
accident.
•
• Do not connect P and P1 connectors used for our EGRET 29
game machine. It may cause a problem or accident.

4
..

• Maintenance

ACAUTION
• Use 01 parts other than genuine Taito parts in the
maintenance will be regarded as unauthorized modification .
We will nol repair any modified machines. Never modify the
machine. II may cause a problem or accident.

• Turn OFF the power switch of the enclosure before

performing maintenance. .

• Before removing the game (mother) PC board from the

enclosure, turn OFF the power switch.

• Maintenance 01 the game (mother) board should be

performed by arcade maintenance men.

• • Be careful not to injure yourself on the soldered side 01 the

game (mother) PC board when working with it. .

• Make sure to lurn OFF the power switch before pulling out or
pulling in the connector or the G card from the game (mother)
PC board, or changing the DIP switches settings.

• The game (mother) PC board may b e damaged by a static

electricity, since it consists of precision parts.

• Do not drop the game (mother) PC board, give 11 a strong

shock on, or louell it with wet hands. It may cause a problem
or accident.

•
5
 ntents
Preface
Purpose 01 this Instruction manual ..• 1

For contact .......... .... ... . . .. 1

Contents of this Instruction manual . . .. ...................... 1

Important information for safety

Definition of personnel in this manual: . .............. ... .. ................. ... 2
· Management staff
· Arcade maintenance man
· Engineer
· Player
· GaUery

Explanation of the safety symbols ..................... ................... . .... 2

Contents
Cautions lor salety .....
· Product overview
· Installation
· Maintenance
............................................................... 3

•
Product Overview .... ......................................... 8
· "TA lTO G NET- game machine
· Instruction manual
• Handling the package carlon boxes
• Handling this product

•
6
 Name of each part ... . ......... 11
· Edge connector
, 3P and 4P connectors
· Exteri or speaker OulpullerminaJ
· External video outpullerminal
· DIP switch
· Sound level adjusting dial
· Changeover switch between stereophonic and monophonic sound
· G c ard insert s lot

Product specification Jist

Chapter 1: Insta llation

1·1 . Installation requirements 16

1·2. In stallation .... ........... " .. .... ...... ........... . . .......... .... ... .... .. ............. ... 17

• Chapter 2: Operation checks

2-1 . Supplying the power ...

2·2. How to lurn the power OFF ..

.. .... 25

.25

2·3. S tart check .... ........... . . .. 25

Chapter 3: Maintenance

Chapter 4: Disposal

Chapter 5: Troubleshooting
5- 1. Error message _ ....................... . ................................................. ... 28

5-2. Troubleshooting ..... ........... ..... ...... ....... ......... ................. . ...29

•
7
 "'~"'uct Ov
Checking the packed items
Make sure thaI all Hems are delivered be f ore installation . II there is any sho rted . or missed item , contact the
dealer whe re you purchased the game machine .

Mother PC board
(M43 *0337 A)
•
TA.lTa

TRWJNET
'- •.
~- '-'~ ~- I
Instruction Manual

E\;:-:::-'- 1
Instruction manual
(G2SOO879A)
•
8
..

• " TAITO G NET" game machine

This machine cons isIs 01 a mother PC board (a SEtI 01 the main PC board and the Fe PC boa rd). II
cannot function withoullhe G card (game) .
By installing the G card (game), the mother PC board becomes Ihe game PC board. By installing this
game PC board into the enclosure, the game machine wililunction. [This product does nOI include Ihe
G card (game).]

• Instruction manual
This manual includes handling methods and ca ut ions lor using the mot her PC boa rd game mac hi ne
safely and appropriately. Keep this manual in a sale place so that it can be used as a reference at any
lime. II you lose t his manua l, contac t the dealer where you pu rchased the machine.

• Handling the package carton boxes

Mother PC board is packaged in carlon boxes for p rotection at delivery.
Keep the package boxes in a sale place so that it can be used again when storin g or transporting the

•
boards l or repairs .

•
 .,

• Handling th is product N
This product is an arcade use mother PC board consis ting 01 precision parts.
Be sure to handle it carefully.

ACAUTION
• Be careful not to injure yourself on the soldered side of the
game (mother) PC board when working with it.

• Make sure 10 turn OFF the power switch before pulling out or
putting in the connector or the G card from the game (mother)
PC board, or changing the DIP switches settings.

• The game (mother) PC board may be damaged by a static

electricity, since it consists of precision parts.

• Do not drop the game (mother) PC board, give it a strong

shock on, or touch it with wet hands. If may cause a problem
or accident.

• Make sure to turn OFF the power switch before changing the
sound between stereophon ic and monophonic.
•
• If you adjustlhe output voltage of the switching regulator
higher than the standard value, the game (mother) PC board
or the G card may be damaged.

• Do not measure points using a tester. even if the game

(mother) PC board is obviously defective .

• Betore inserting a G card, make sure to turn OFF the powe r

switch first, and then insert it into the G card insert slot slowly
and securely while making sure 01 the direction. Otherwise, it
may cause a problem or accident.

• Do nol make the G card insert slot wet or dirty. It may cause a
problem or accident.

• Never insert cards other than the G card into the G card insert

•
stoUt may cause a problem or accident.

• Do not drop the G card,giv8 it a slrong shock on, or louch or

disassemble it with wet hands. It may cause a problem or
· accident.

10
, .

Name of each part

• Fe PC board

Main PC board
A·set of the main PC board an d Fe PC board is referred to as th e mother PC board .

11
 "

• Edge connector
An edge connector is used to con nect the game PC board electrically to the outside.

•
• 3P and 4P connectors
3P and 4P (;onn61;Io r::; afe im,lalleo UI1 Ihl;;l Iliaill PC uoald.

External drawings Terminal No. Description

1 Coin counter 3
2 Coin lockout 3
\ 2 3< S, 1 S "0,"2 " " "
3 Coin switch 3
raeJjo 0 0 0 0 0 0 0 0 0 0 0 00 01 4 Start switch 3
(Top View) 5 Control 1 UP
6 Control 2 DOWN
7 Control 3 LEFT

, ~ 3' S
[!fJ 10
e 78"0"'1'3""
00 0 000 0 0 0 0 0 00

(Top View)
01
•
9
10
11
12
13
Conlrol4 RIGHT
Control 5 PUSH1
Control 6 PUSH 2
Control 7 PUSH 3
Control 8 SPARE
Control 9 SPARE
•
14 HN HOLDt
15 GND

12
 • Exterior speaker output terminal
This lerminal is used 10 out put sound t rom the power amplifier which is mounted on the main PC board.

External drawings Terminal No. Description

1 2 3 4 1 Lett speaker .)
1
0000
1 2 Left speaker -)
i SPEAKER ! 3 Right speaker (-)
(Top View) 4 Right speaker (+)
,

• External video output terminal

T his terminal is used to output the video image signal to an external compons.nt.

External drawings Terminal No. Description

1 Video RED
'23456 2 Video GREEN
10000 001

•
3 Video BLUE
~ 4 Video SYNC
(Top View) 5 GND
,
• Fsc (3.S8MHz)

• DIP switch
T he DIP switches are used to enter the test mode.
For details about how to set and operate the test mode , see the instruction manual of the G card (game).
(This product does nol include th e instruction manual of the G card (game). )

~u----------~
. There are two methods to stan the test moda: A method which uses the
lest switch on the enclosure and a method which uses the DIP switches
on the mother PC board.
When using the test switch on the enclosure, refer to the instruction
manuat of the enclosure and start the lest mode.

• e(
1 2 3 4

OFF
Operate No.4 only.

13
 • .,

• Sound level adju sting dial

This is a ha rdware sound level adjusting dial Installed on the main PC board.

External drawings Function

~
~ H~
The sound lavel is raised by turning the
sound leval adjusting dial to the right,
Low
sound level sound level as viewed Irom above the main PC
board, and lowered by turning illo the
SPUK:£R VOlVIoIE
left.
(Top View)

• Changeover switch between stereophoni c and monopho nic sound

This switch is used to change the sound 'output be"tween monophonic sound and stereophonic sound.
The switch has been set at monophonic sound when shipped.

ACAUTION
Make sure to turn OFF the power switch before changing the
sound between stereophonic and monophonic.
•
~g ----------~
. Use the "exterior speaker output terminal- to output the stereo sound.

Extemal drawings Function

When setting the changeover switch to
stereophonic sound, the 2 channel
signals from the edge connector emit
[l"![] the sounds of the left and righl speakers

•
~ iWClNOi of the enclosure, respectively. When
selling tile changeover switch to
4 I monophonic sound, the sound signal ,
Stereophonic Monophonic
sound sound
from tile edge connector emits the same
sound fro m the lert and right speakers.
I.
(Top View)

14
"

• G card insert slot

In this system, the game PC board can b e started by inserting
the G card (game) lnlo the G card insert
slol.

Product specification list

Item Specific ation data

Rated input voltage 5V DC (4A Of more)
(curlen!)
12VOC (2A or more)
Raled consumption power Approx. 30W
Weight Approx. 650 (9)
External dimensions 265 (widlilj X 70 (heigh1) X 27() (depth) m m

•
L{)
CD
N

~W::2~~
• I 265 I

15
 Chapter 1 Installation

• 1-1. Installation
requirements ACAUTION
Make sure to follow the installation requirements .

. For how to install the enclosure , see the instruction manual for the
enclosure .

~g----------~
. For detai ls about the G ca rd , see th e game instruction manual for the
-T AlTO G CARD."

Ins talli he mother PC boa rd into an en closure wh ich meets the follow ing
requirements.

An enclosure in which the game PC board based on the JAMMA

sta n dard can be insta lled.

· An enclosure which is equipped w ith a switched powe r supply co mp lying

with the requirements of this produ ct spec ificati o ns .

· Has enough space to install the game PC board.

· Monitor's sync hrono us frequency is 15 KHz.

· The operat ion system must meet the following requirements .

Nameoll Ihe edge connector terminal

Name lP side 2P side
a-directional;oy Slick (up ) l P CONT ROLLEl UP 2P CQNTR OLL E 1 UP
8-directiona l joy stick (down) IP CONTROLLE2 DOWN 2P CONTAOLLE2 DO WN
a-directional joy stick (Iell) lP CONTR OLLE3 LEFT 2P CONTROLLEJ LE FT
8-directional joy stick (rig hI) 1P CONTAOtLE4 RIGHT 2P CONTROLLE4 RIGHT
5 1afl bullon ST AAT SW I STAAT SW2
BunonA 1P CONTAOLLE5 PUSHI 2P CONTROlLE5 PUSHI
ButtonB 1P CONTROLLES PUSH2 2P CONTROLLE6 PU SH 2
B ul10nC I P CONTROLL E7 PUSH J 2P CONI ROlLE 7 PUSH)

16
 Chapter 1 Installation

• 1-2. Installation
ACAUTION
• Turn OFF the power switch of the game machine before
installation.

• Before removing the game (mother) PC board from the game

machine, turn OFF the power switch.

• Be carefu l not to injure yourself on the soldered side of the

game (mother) PC board during installation.

•
• Make sure to turn OFF the power switch before pulling out or
putting in the connector or the G card from the game (mother)
PC board, or changing the DIP switches settings.

• The game (mother) PC board may be damaged by a stafic

electricity, since it consists of precision parts.

• Do not drop the game (mother) PC board, give it a strong

shock on. or touch it with wet hands. If may cause a problem
or accident.

• Never insert cards other than the G card into the G card
insert slot.it may cause a problem or accident.

• Do not drop the G card,give it a strong shock on, or touch or

disassemble it with wet hands. It may cause a problem or
accident.

•
• Do not connect P and Pl connectors used for our EGRET 29
game machine. It may cause a prob lem or accident.

17
 Chapter 1 Installation

~ g----------~
. For how to install the en clos ure, see the instruction manua l for the
enclosure.

~ g----------~
. For details about the G card, see the game instruction man ual for the
"TAlTO G CARD."

EGRET 29 game machine

Make sure to disconnect.

"P1 "

. . Turn OFF the power sw itch of the enclosure .

. . Open the game PC board outlet of the enclosure .

. . If another game PC boa rd is already insta lled, remove it.

18
 --~

Chapter 1 Installation

. . Install the mother PC boa rd on the game PC board mounting plate of

the enclosu re.
(When screwing the system PC board on the enc losu re , install it by
tightening screws allour Ress Lock mounting holes.)

-:::::::--''-' ::::-- :::::O>;r Sc few in .

• > Mother PC board

).:( Game PC board fixing

plate of the enclosure

. . Co nnect the JAMMA harness inside the enclos ure to the mother PC
board 's edge connector.

~ g--------------~
. Install the mother PC board so th at the harness and other parts will not
touch the game PC board .

• Mother PC board

JAMMA harness

19
 . . Install the G card (game) in the mother PC boa rd.
[The G card (game) is not included w ith this product.]

ACAUTION
• Before inserting a G card, make sure to turn OFF the powe r
switch first, and then insert it into the G card insert slot slowly
and securely while making sure of the direction. Otherwise, it
may cause a problem or accident. Inserting it forcibly may
cause a prob lem .

• Do not make the G card insert slot wet or dirty. It may cause _
a problem or accident.

1. Insert the G card (game) into the mother PC board .

Insert the G card (game)
G card (game ) aligning the groove .

,
Mother PC boa rd

2. The mother PC board will be a game PC board after install ing

the G card (game).

Game PC boa rd

20
 •

Chapter 1 Installation

• How to insert the G ca rd (game)

Insert the G ca rd into the groove to the end .

•
Game label side

• How to pull out the G ca rd (game)

• 2. When the G card (game)

comes oul a little, pull
it out by a hand .

1. Push he re.

21
r

Chapter 1 Installation

. . Check that the G card (game) is installed correct/yo

PUSh in Ihe G ca'~ 10 the eM

wilen the pin awears as sr>own
in Ihe livu re.

The G ca'" lQarne) is ~'Sla lled correctly wnen 'l oS ,nserleO

10 lhe en<l ""thout deviation

)( U

)( :,,"1::<
U
~=~=_
~
...
. ,~I [~.:o:~,.,,,, ~ TheGca ra(g ame)is insla liedSlantw is.OoMl 1"s€ n "
lO,e,OI)-
fle.n Slall il again

The G CJI d (game) , 1,<Ie" Irom Ihe groove. Do n01 in~" f1 il

lorClb/y
ReU1 slai l il aga,"
•
O~a
)( fr ---"¥itt TM G card Igame-I laces
insen
j" 1M oppos ile dl(ectlon Do flOI
il l orcibly_C t.e, " the S,de and reInstal l " aoa ,n

. . After installing the G card (game) correctly, turn ON the power switch of
the enclosure.
(If the G card is not instaJJed correctly, start the installation again from
the beginning.)

. . Adjust the supply power voltage to the game PC board with the reference
voltage.

•
ACAUTION
Make sure to adjust the voltage.

22
 •

Chapter 1 Installation

ACAUTION
If you adjust the output voltage of the switching regulator
higher than the standard value, the game (mother) PC board
or the G card may be damaged .

Edge co n ne c tor
termi na l N o. Reference
vo lt age
-
+
,
•
3 5V
Parts 5V
4 2
mounte d
s ide 6 1 '2V
6 2 ,2V
C A 5V
Soldered 0 B 5V
si de F A '2V
F B '2V

Make sure to adjust the power voltage of the switching power

supply so thaI the voltage between edge connect or NO. 1 and
NO. 3 is 5 V .

•
Ad'us! the volta e to SV .

23
 Chapter 1 Installation

~ T urn O F F the power sw itch of the enc losu re .

CII Close the game P C board outle t of the enclosu re.

24
~ Operation checks)
•

• 2-1. Supplying the power .. Turn OFF the power switch of the enclosure.

tfa Co nn ect th e enclosure power plug to power outlet.

. . Turn ON the enclosu r e powe r swi tch .

• 2-2. How to turn the . . Turn OFF th e enclosure power switch

power OFF

• 2-3 . Start check The game wiH not start if the G card (game) is nol installed in the mothe r PC
board .

•
For details of the start check , see the instruction manual for the G card
(game).
[This p roduct does not inc lude the instruction manual for the G card
(game ).)

25
 •

Chapter 3 Maintenance

ACAUTION
• Use of parts other than genuine Taito parts in the
maintenance will be regarded as unauthorized modification.
We will not repair any modified machines.Never modify the
machine. It may cause a problem or accident.

• Turn OFF the power switch of the enclosure before

performing maintenance.

• Before removing the game (mo ther) PC board from the

enclosure, turn OFF the power switch.

• Maintenance of the game (mother) boa rd should be

performed by arcade maintenance men.

• Be ca reful not to injure yourself on the soldered side of the

game (mother) PC board when working with it.
•
• Make sure to turn OFF the P9wer switch before pulling out or
putting in the connector or the G card from the game (mother)
PC board, or changing the DIP swi tches settings.

• The game (mother) PC board may be damaged by a static

electricity, since it consists of precision parts.

• Do not drop the game (mother) PC board, give it a strong

shock on, or touch it with wet hands. It may cause a problem
or accident.

When you do not use th e mothe r PC board , put it in the package b ox

and keep it in safe place .
Do not keep the mother PC board in locat ions shown be l ow .
· Location where it wHI be exposed to direct sunlight.
· Location with high humidity.
· Location with much dust.
· Unstab l e locat ion
· Location subject 10 vibra ti on, sta tic electricity, or electromag-
netic wave .

26
 •

) Chapter4 DisDCJsal

When disposing of the mothe r PC board the owner must take responsibility for
handling it as industrial waste.
The mot her PC board is protected by packing materials whe n shipped. Follow
the instructions of the local authorities when disposing of Ihese packing materials .

27
 •

ChapterS Troubleshootin

5-1. Error message

Screen display Contents Treatment

• This e fror occurs when it takes
COIN ERROR one second or longer for the coin Read the instruction manual of
inserted into the enclosure to pass
the enclosure.
through the micro-switch inside
the rejecter.

SERV ICE SW ERROR • The service switch inside the

enclosure is turn ed ON by being
caught due to damage. Read the instruction manual of

• The harness connected to the

service switch is shorted.
the enclosure.

•
TILT • The tilt sensor is functioning. Read the instruction manual of
the enclosure.

28
 •

Chapter 5 Troubleshooting

5-2. Troubleshooting

Trouble Possible cause Treatment

· The game PC board cannot read

the program from the G card · Check if the G card (game) is inserted secure ly.
(game). (Installation -* Page 22)

· The G card is broken due to · Replace the G card .

The game PC board shock or static electricity .
repeats resetting .
The power voltage is not · Adjust the switching power voltage .
appropriate. (Installation""'" Page 23)

•
· The edge connector is badly · Remove dirt on the edge con nector terminal side
connected . using a clean and soft cloth.

o The harness is disconnected

· Replace the harness.
or shorted.

· The sound level setting on the main · Turn the sound level adjusting dial clockwise to
The sound level PC board is set to fower vofume . full volume. (Name of each parts-+ Page 11)
is low.
· The sound fevel on the enclosure · Turn the sound level adjusting dial inside the
side is set to lower volume. enclosure.

· The power voltage is not · Adjust the switching power voltage.

appropriate . (Installation -~ Page 23)

The system · The enclosure power is connected

sometimes resets by the same power line to the
· Change the power supply to the enclosure.
or the screen stops vending machine, refrigerator,
displaying. or air conditioner.

· The game PC board is broken

· Replace the game PC board.
due to shock or static electricity.

•
· The power is not supplied to the · Insert the plug after turning OFF the power switch.
power plug of the enclosure . Then, turn ON the power switch again.

· The JAMMA harness is not · Insert the JAMMA harness securely after checking
connected correctly. the connector direction.

· The JAM MA harness is

· Replace the JAMMA harness.
disconnected or shorted

· The harness spec ifications are

· Replace it with the correct harness
No operation is not appropriate.
periormed.
· The power voltage is not · Adjust the switching power vo ltage
appropriate. (Installation -- Page 23 )

· The game PC board is

broken due to shock or static · Replace the game PC board.
electric ity .

· Replace the fuse after checking if the harness

The fuse is blown off. shorts with the game PC board or other
components.

29
 •

TAITO CORPORATION®
©TAITO CORP. 1998 PRINTED IN JAPAN