MASTERTOP® 1110M

Water-based epoxy floor and wall coating for concrete and masonry surfaces

Description of Product Advantages

MASTERTOP 1110M is a two-component, • Moisture tolerant
water dispersible, epoxy resin coating, • Economical
designed to seal and protect concrete and • Easy application
cementitious floors and walls. • Solvent-free, non-tainting
• Easily cleaned
Primary Uses • Dust-free surface
MASTERTOP 1110M gives good general
• Ease of maintenance
protection for concrete surfaces and
• Good bond to dense surfaces
provides an easily cleaned, non-dusting
finish in numerous industrial and commercial
Packaging
applications. The system is free of organic
MASTERTOP 1110M is supplied in a 5kg
solvents and will not taint foodstuffs.
unit.
MASTERTOP 1110M can be successfully
Colours
applied to damp concrete surfaces making it
MASTERTOP 1110M is available in the
particularly suitable for wet process
following colours: light grey; dark grey; dust
industries, where a dry substrate may be
grey; red; blue beige; green and white
difficult or impossible to obtain.

MASTERTOP 1110M offers good resistance Typical Properties

Pot Life: 20°C 1 hour
to a wide range of chemicals and aggressive
Specific gravity: (varies with 1.35-1.45g/cm³
liquids, but as in all corrosive situations, a
colour)
full analysis of operating and exposure
Max. service temperature: 60°C
conditions is required, followed by reference Min. recoat time: 10 hours at 25°C
to chemical resistance data, to ensure Max. recoat time: 48 hours at 25°C
product suitability. D.F.T.: 75-100 microns per
coat
MASTERTOP 1110M can also be applied to
act as a combined sealer/coating/curing Hygiene
membrane provided that the concrete has From all available information it has been
hardened sufficiently. found that MASTERTOP 1110M shows a
minimal risk of tainting foodstuffs during and
MASTERTOP 1110M is used extensively in after complete cure has taken place.
the following application areas as a sealing
coat and wearing surface to epoxy toppings Application Procedure
and screeds: Preparation:
• Dairies MASTERTOP 1110M can be applied to a
• Abattoirs clean, dry or damp but not wet, substrate
• Fish and meat processing plants free from dust, dirt, oil, grease and other
• Warehousing contaminants. A clean surface will ensure
• Soft drink and beverage production improved adhesion between substrate and
• Manufacturing and food processing coating.
• Bakeries The method of surface preparation will be
• Wash and changing room walls dictated by the size of area to be treated,
• Pharmaceutical factories location and degree of contamination.
• Industrial and commercial kitchens
MASTRTOP® 1110M

New construction: Substrates that are porous should be primed

Floors to be coated or overlaid should be at using MASTERTOP 1110M diluted with up
least 7 days old unless water-reducing to 10% by volume of water per 4kg pack.
admixtures have been incorporated. (Consult Coverage will be approximately 5-
MBT’s Technical Services Department for 7m²/kg/coat.
advice). The removal of laitance and
contaminants is best achieved by Mixing should be as described above.
mechanical means, such as vacuum Application should be by short haired roller
recovery shot blasting. or airless spray.

Existing concrete: Coating application:

All contamination must be removed and a Apply 2 coats of MASTERTOP 1110M at
sound clean substrate exposed. Mechanical 5-8m²/kg/coat and allow at least 6-8 hours
means of preparation are preferred followed but no more than 48 hours between coats.
by the removal of dust and other loose
debris using an industrial vacuum. In areas Apply the second coat at right angles to the
of deeply penetrating contamination by oils, first. MASTERTOP 1110M should be
greases and fats, hot compressed air allowed to cure for 48 hours prior to
treatment followed by impregnation with a receiving light traffic. Full cure is achieved
low viscosity sealer / primer is the after 7 days. As with all water-based
recommended treatment. systems, good ventilation and air movement
is required to assist drying, especially in
Prior to application, MASTERTOP 1110M damp conditions.
should be stored under cover and protected
from extremes of temperature which will Slip-Resistant Coatings
cause inconsistent workability and cure Where slip resistance is required,
times of the mixed material. During MASTERTOP SLIP-RESISTANT
application in cold conditions, correct AGGREGATE NO. 1 (SRA NO. 1M) is
conditioning is essential; but application broadcast into the wet base coat, to
should be halted if the ambient temperature saturation. Leave overnight to dry then
is likely to fall below 10°C. Consideration remove excess aggregate by sweeping or
should be given to the substrate or base vacuuming, before applying the topcoat.
slab, as it is likely to be considerably colder When a slip-resistant finish is applied in
than the ambient air temperature. areas that will be wet and/or suffer from
chemical spillage, a primer coat must always
Mixing: be applied.
MASTERTOP 1110M is a two-component
product consisting of base and reactor Consumption:
components. The base component should BASE COAT 6.5-7m²/kg
be mixed before use to redistribute any AGGREGATE 1.5-2kg/m²
settlement that may have occurred during TOP COAT 5-6m²/kg
storage.
Coverage will vary according to the nature of
To the pre-mixed base add the complete the substrate. All calculated usages assume
contents of the reactor container. Using a constant thickness on a regular substrate.
slow speed drill with a suitable mixing Failure to achieve the required surface
attachment, mix for 1-2 minutes until a regularity will lead to additional material
uniform streak free consistency is achieved. being used.
MASTERTOP 1110 M is supplied in
preweighed units; at no time should packs
be split.

Priming:
MASTERTOP® 1110M

Storage Quality Statement

Store under cover, out of direct sunlight and All products manufactured by MBT Egypt, or
protect from extremes of temperature. In imported from MBT affiliate companies
tropical climates, the product must be stored world-wide, are manufactured to procedures
in air-conditioned environment. certified to conform to the quality
management systems described in the
Failure to comply with the recommended ISO 9000 series.
storage conditions may result in premature
deterioration of the product or packaging. 12/04 MBT-EG
For specific storage and disposal advice,
consult MBT's Technical Services * Properties listed are only for guidance and are not a
Department. guarantee of performance.

Shelf Life
Up to 12 months if stored in unopened
containers according to manufacturer’s
instructions.

Safety Precautions
As with all chemical products, care should be
taken, during use and storage, to avoid
contact with eyes, mouth, skin and foodstuffs
(which can also be tainted with vapour until
product has fully cured or dried). Treat
splashes to skin and eyes immediately. If
accidentally ingested, seek medical
attention. Re-seal containers after use. For
further information, refer to the material
safety data sheet.

Note
Field service, where provided, does not
constitute supervisory responsibility. For
additional information, contact your local
MBT representative.

MBT reserves the right to have the true

cause of any difficulty determined by
accepted test methods.

MBT, Egypt Tel.: +202 3453483/4 Whilst any information contained herein is true, accurate and
94 Shehab St. Mohandessin Fax: +202 3453481 Sales represents our best knowledge and experience, no warranty is given
Giza – Egypt Fax: +202 3453482 Admin. or implied with any recommendations made by us, our
Factory: Sadat City, Piece 118 Tel.: +2048 2604842 representatives or distributors, as the conditions of use and the
Zone 4 Fax: +2048 2604757 competence of any labour involved in the application are beyond our control.

Certificate No. 158171

008

email: enquire.egypt@degussa.com, website: www.mbt-egypt.com

As all MBT technical datasheets are updated on a regular basis, it is the user’s responsibility to obtain the most recent issue. Most recent issue is available on the website at
www.mbt-egypt.com