Scribd
Upload
19 views2 pages

Eep

The document contains G-code instructions for machining a cylinder workpiece. It defines tool paths for roughing and threading operations using cycles for profiling, threading, and tool changes. The profiling cycle machines a contour with rounded corners on the cylinder. The threading cycle cuts an internal M10 thread.

Uploaded by

Vitor Vidigal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
19 views2 pages

Eep

The document contains G-code instructions for machining a cylinder workpiece. It defines tool paths for roughing and threading operations using cycles for profiling, threading, and tool changes. The profiling cycle machines a contour with rounded corners on the cylinder. The threading cycle cuts an internal M10 thread.

Uploaded by

Vitor Vidigal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

N10 WORKPIECE(,,,"CYLINDER",192,0,-60,-51,34)

N20 G291
N30 G21 G40 G90 G95
N40 G54G0X150Z150
N50 T0301
N60 G96 S200
N70 G92 S2500 M4

N80 G0 X35 Z5
G290
CYCLE62("PESS",1,,)
CYCLE952("DESBASTE",,"",1101331,0.1,0.12,0,1,0.1,0.1,0.1,0.1,0.1,0,1,0,0,,,,,2,2,,,
0,1,,0,12,1100010,1,0,0.1)

T05D1
G291
G96 S190
G92 S2000 M4

G0 X20 Z-31
G1 X10
G0 X20 Z-29
G1 X10
X12
X16 Z-27
X20
G54 G0 X150 Z150
G290
T="THREADING_1.5"
G291
G96 S200
G92 S2200 M4

CYCLE99(0,16,-
30,,1,2,0.9201,0,30,0,4,0,1.5,1110101,4,2,0.3,0.5,0,0,1,0,0.53122,1,,"ISO_METRIC","
M10",102,0)
M30

E_LAB_A_PESS: ;#SM Z:6


;#7__DlgK contour definition begin - Don't change!;*GP*;*RO*;*HD*
G18 G90 DIAM90;*GP*
G0 Z0 X10 ;*GP*
G1 X12 ;*GP*
Z-2 X16 ;*GP*
Z-31 ;*GP*
X22 RND=2 ;*GP*
Z-36 RND=2 ;*GP*
X26 ;*GP*
Z-41 ;*GP*
X29 ;*GP*
Z-43 X32 ;*GP*
Z-50 ;*GP*
X34 ;*GP*
;CON,V64,2,0.0000,11,11,MST:3,2,AX:Z,X,K,I,TRANS:0;*GP*;*RO*;*HD*
;S,EX:0,EY:10,ASE:90;*GP*;*RO*;*HD*
;R,RROUND:0;*GP*;*RO*;*HD*
;LU,EY:12;*GP*;*RO*;*HD*
;LA,EX:-2,EY:16;*GP*;*RO*;*HD*
;LL,EX:-31;*GP*;*RO*;*HD*
;LU,EY:22;*GP*;*RO*;*HD*
;R,RROUND:2;*GP*;*RO*;*HD*
;LL,EX:-36;*GP*;*RO*;*HD*
;R,RROUND:2;*GP*;*RO*;*HD*
;LU,EY:26;*GP*;*RO*;*HD*
;LL,EX:-41;*GP*;*RO*;*HD*
;LU,EY:29;*GP*;*RO*;*HD*
;LA,EX:-43,EY:32;*GP*;*RO*;*HD*
;LL,EX:-50;*GP*;*RO*;*HD*
;LU,EY:34;*GP*;*RO*;*HD*
;#End contour definition end - Don't change!;*GP*;*RO*;*HD*
E_LAB_E_PESS:

You might also like