Quick Start

Thank you for purchasing the MSI® MAG B560 TOMAHAWK WIFI/ MAG B560
TORPEDO motherboard. This Quick Start section provides demonstration diagrams
about how to install your computer. Some of the installations also provide video
demonstrations. Please link to the URL to watch it with the web browser on your
phone or tablet. You may have even link to the URL by scanning the QR code.

Preparing Tools and Components

Intel® LGA1200 CPU

CPU Fan
Chassis

DDR4 Memory

Power Supply Unit

Graphics Card

Thermal Paste

SATA Hard Disk Drive

SATA DVD Drive

Phillips Screwdriver A Package of Screws

Quick Start 1
 Safety Information
∙∙ The components included in this package are prone to damage from electrostatic
discharge (ESD). Please adhere to the following instructions to ensure successful
computer assembly.
∙∙ Ensure that all components are securely connected. Loose connections may cause
the computer to not recognize a component or fail to start.
∙∙ Hold the motherboard by the edges to avoid touching sensitive components.
∙∙ It is recommended to wear an electrostatic discharge (ESD) wrist strap when
handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is
not available, discharge yourself of static electricity by touching another metal object
before handling the motherboard.
∙∙ Store the motherboard in an electrostatic shielding container or on an anti-static
pad whenever the motherboard is not installed.
∙∙ Before turning on the computer, ensure that there are no loose screws or metal
components on the motherboard or anywhere within the computer case.
∙∙ Do not boot the computer before installation is completed. This could cause
permanent damage to the components as well as injury to the user.
∙∙ If you need help during any installation step, please consult a certified computer
technician.
∙∙ Always turn off the power supply and unplug the power cord from the power outlet
before installing or removing any computer component.
∙∙ Keep this user guide for future reference.
∙∙ Keep this motherboard away from humidity.
∙∙ Make sure that your electrical outlet provides the same voltage as is indicated on
the PSU, before connecting the PSU to the electrical outlet.
∙∙ Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
∙∙ All cautions and warnings on the motherboard should be noted.
∙∙ If any of the following situations arises, get the motherboard checked by service
personnel:
▪▪Liquid has penetrated into the computer.
▪▪The motherboard has been exposed to moisture.
▪▪The motherboard does not work well or you can not get it work according to user
guide.
▪▪The motherboard has been dropped and damaged.
▪▪The motherboard has obvious sign of breakage.
∙∙ Do not leave this motherboard in an environment above 60°C (140°F), it may damage
the motherboard.

2 Quick Start
Case stand-off notification
Before installing the motherboard into the case, install first the necessary mounting
stand-off required for a motherboard on the mounting plate in the case.
To prevent damage to the motherboard, any unnecessary mounting stand-off between
the motherboard circuits and the computer case is prohibited. The Case standoff keep
out zone signs will be marked on the backside of motherboard (as shown below) to
serve as a warning to user.

Quick Start 3
 Installing a Processor
2

⚽⚽
1
https://youtu.be/4ce91YC3Oww

7
4 5 9
6

4 Quick Start
Installing DDR4 memory

⚽⚽
http://youtu.be/T03aDrJPyQs

DIMMA1
DIMMA2 DIMMA2 DIMMA2
DIMMB2 DIMMB1
DIMMB2

Quick Start 5
 Connecting the Front Panel Header

⚽⚽
http://youtu.be/DPELIdVNZUI

-
LED
ER W
+ PO
ED
RL E
OW P
ED
DL
W

HD
RS
WE
PO
W
TS
SE
RE

Power LED Power Switch

+
+
-
-

2 10
RESET SW

JFP1 1 9
HDD LED

Reserved
+

+
-
-

HDD LED Reset Switch

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch JFP1

9 Reserved 10 No Pin

HDD LED -
HDD LED
HDD LED +

POWER LED -
POWER LED
POWER LED +

6 Quick Start
Installing the Motherboard

⚽⚽
https://youtu.be/wWI6Qt51Wnc

Torque:
3 kgf·cm*
2
BAT1

*3 kgf·cm
= 0.3 N·m
= 2.6 lbf·in

Quick Start 7
 Connecting the Power Connectors

⚽⚽
http://youtu.be/gkDYyR_83I4

PCIE_PWR1

ATX_PWR1

CPU_PWR2

CPU_PWR1

8 Quick Start
Installing SATA Drives

⚽⚽
http://youtu.be/RZsMpqxythc
1

2
3

Quick Start 9
 Installing a Graphics Card

⚽⚽
http://youtu.be/mG0GZpr9w_A

3 2

10 Quick Start
Connecting Peripheral Devices
∙∙ MAG B560 TOMAHAWK WIFI

Quick Start 11
 ∙∙ MAG B560 TORPEDO

12 Quick Start
Power On

1 2

Quick Start 13
 NOTE

14 Quick Start
Contents
Quick Start.............................................................................................................. 1
Preparing Tools and Components.......................................................................... 1
Safety Information................................................................................................... 2
Case stand-off notification...................................................................................... 3
Installing a Processor............................................................................................. 4
Installing DDR4 memory......................................................................................... 5
Connecting the Front Panel Header....................................................................... 6
Installing the Motherboard...................................................................................... 7
Connecting the Power Connectors......................................................................... 8
Installing SATA Drives............................................................................................. 9
Installing a Graphics Card..................................................................................... 10
Connecting Peripheral Devices............................................................................. 11
Power On............................................................................................................... 13
Specifications........................................................................................................ 17
Package contents................................................................................................. 24
Block Diagram ..................................................................................................... 25
Rear I/O Panel...................................................................................................... 26
LAN Port LED Status Table................................................................................... 27
Audio Ports Configuration..................................................................................... 27
Realtek Audio Console.......................................................................................... 27
Overview of Components..................................................................................... 31
CPU Socket............................................................................................................ 33
DIMM Slots............................................................................................................. 34
PCI_E1~3: PCIe Expansion Slots........................................................................... 35
JAUD1: Front Audio Connector............................................................................. 35
M2_1~3: M.2 Slots (Key M).................................................................................... 36
SATA1~6: SATA 6Gb/s Connectors........................................................................ 38
JFP1, JFP2: Front Panel Connectors.................................................................... 39
JTPM1: TPM Module Connector............................................................................ 39
CPU_PWR1~2, ATX_PWR1, PCIE_PWR1: Power Connectors.............................. 40
JUSB4: USB 3.2 Gen 2 Type-C Connector............................................................. 41
JUSB3: USB 3.2 Gen 1 Connector......................................................................... 41
JUSB1~2: USB 2.0 Connectors.............................................................................. 42
JTBT1: Thunderbolt Add-on Card Connector....................................................... 42
CPU_FAN1, PUMP_FAN1, SYS_FAN1~5: Fan Connectors................................... 43
JCI1: Chassis Intrusion Connector........................................................................ 44
JBAT1: Clear CMOS (Reset BIOS) Jumper............................................................ 45

Contents 15
 JDASH1 : Tuning Controller connector................................................................. 45
JRGB1~2: RGB LED connectors............................................................................ 46
JRAINBOW1~2: Addressable RGB LED connectors............................................. 47
Onboard LEDs....................................................................................................... 48
EZ Debug LED........................................................................................................ 48
LED_SW1: EZ LED Control.................................................................................... 48
Installing OS, Drivers & MSI Center..................................................................... 49
Installing Windows® 10.......................................................................................... 49
Installing Drivers................................................................................................... 49
MSI Center............................................................................................................. 49
UEFI BIOS.............................................................................................................. 50
BIOS Setup............................................................................................................. 51
Entering BIOS Setup.............................................................................................. 51
BIOS User Guide.................................................................................................... 51
Resetting BIOS....................................................................................................... 52
Updating BIOS........................................................................................................ 52
Intel® Optane™ Memory Configuration............................................................... 54
Troubleshooting .................................................................................................. 55

16 Contents
Specifications
∙∙ Supports 10th Gen Intel® Core™ Processors, 11th Gen
Intel® Core™ Processors, Pentium® Gold and Celeron®
Processors*
CPU
∙∙ Processor socket LGA1200
* Please go to intel.com for compatibility information.

Chipset Intel® B560 Chipset

∙∙ 4x DDR4 memory slots, support up to 128GB*

▪▪Supports 1R 2133/ 2666/ 2933 MHz for 10th Gen Intel®
CPU (by JEDEC & POR)
▪▪Supports 1R 2133/ 2666/ 2933/ 3200 MHz for 11th Gen
Intel® CPU (by JEDEC & POR)
▪▪Max overclocking frequency:
▫▫1DPC 1R Max speed up to 5066 MHz
Memory ▫▫1DPC 2R Max speed up to 4600+ MHz
▫▫2DPC 1R Max speed up to 4266+ MHz
▫▫2DPC 2R Max speed up to 4000+ MHz
∙∙ Supports Dual-Channel mode
∙∙ Supports non-ECC, un-buffered memory
∙∙ Supports Intel® Extreme Memory Profile (XMP)
* Please refer to www.msi.com for more information on compatible memory

∙∙ 2x PCIe x16 slots

▪▪PCI_E1 (from CPU)
▫▫Support up to PCIe 4.0 for 11th Gen Intel® CPU
Expansion Slot ▫▫Support up to PCIe 3.0 for 10th Gen Intel® CPU
▪▪PCI_E2 (from B560 chipset)
▫▫Support up to PCIe 3.0 x4
∙∙ 1x PCIe 3.0 x1 slot (from B560 chipset)

Multi-GPU ∙∙ Supports 2-Way AMD® CrossFire™ Technology

∙∙ 1x HDMI 2.0b with HDR port, supports a maximum

resolution of 4K 60Hz*/**
∙∙ 1x DisplayPort 1.4 port, supports a maximum resolution of
Onboard Graphics
4K 60Hz*/**
* Available only on processors featuring integrated graphics.
** Graphics specifications may vary depending on the CPU installed.

Continued on next column

Specifications 17
 Continued from previous column

∙∙ 6x SATA 6Gb/s ports (from B560 chipset)

∙∙ 3x M.2 slots (Key M)
▪▪M2_1 slot (from CPU)
▫▫Available only on 11th Gen Intel® CPU
▫▫Supports up to PCIe 4.0 x4
▫▫Supports 2242/ 2260/ 2280/ 22110 storage devices
▪▪M2_2* slot (from B560 chipset)
▫▫Supports up to PCIe 3.0 x4
▫▫Supports SATA up to 6Gb/s
Storage
▫▫Supports 2242/ 2260/ 2280 storage devices
▪▪M2_3 slot (from B560 chipset)
▫▫Supports up to PCIe 3.0 x4
▫▫Supports 2242/ 2260/ 2280 storage devices
▫▫Intel® Optane™ Memory Ready**
∙∙ Supports Intel® Smart Response Technology for Intel
Core™ processors
* SATA2 will be unavailable when installing M.2 SATA SSD in the M2_2 slot.
** Before using Intel® Optane™ memory modules, please ensure that you have
updated the drivers and BIOS to the latest version from MSI website.

∙∙ Intel® B560 Chipset

▪▪1x USB3.2 Gen 2x2 20Gbps port (Type-C port on the
back panel)
▪▪1x USB 3.2 Gen 2 10Gbps port (1 Type-C available
through the internal connector)
▪▪6x USB 3.2 Gen 1 5Gbps ports (4 Type-A ports on the
USB
back panel, 2 Type-A ports available through the internal
connector)
▪▪4x USB 2.0 ports on the back panel
∙∙ Hub-GL850G
▪▪4x USB 2.0 ports available through the internal
connectors

Realtek® ALC897 Codec

Audio ∙∙ 7.1-Channel High Definition Audio
∙∙ Supports S/PDIF output

Continued on next column

18 Specifications
 Continued from previous column

∙∙ 1x Realtek® RTL8125B 2.5Gbps LAN controller

LAN ∙∙ 1x Intel® I219V 1Gbps LAN controller (For MAG B560
TORPEDO only)

Intel® Wi-Fi 6E AX210

∙∙ The Wireless module is pre-installed in the M.2 (Key-E)
slot
∙∙ Supports MU-MIMO TX/RX, 2.4GHz/ 5GHz/ 6GHz*
Wireless LAN & (160MHz) up to 2.4Gbps
Bluetooth® ∙∙ Supports 802.11 a/ b/ g/ n/ ac/ ax
∙∙ Supports Bluetooth® 5.2**, FIPS, FISMA
* Wi-Fi 6E 6GHz may depend on every country’s regulations and will be ready in
WIN10 21H1.
** Bluetooth 5.2 will be ready in WIN10 21H1.

∙∙ 1x 24-pin ATX main power connector

∙∙ 1x 8-pin ATX 12V power connector
∙∙ 1x 4-pin ATX 12V power connector
∙∙ 1x 6-pin PCIE power connector
∙∙ 6x SATA 6Gb/s connectors
∙∙ 3x M.2 slots (M-Key)
∙∙ 1x USB 3.2 Gen 2 10Gbps Type-C port
∙∙ 1x USB 3.2 Gen 1 5Gbps connector (supports additional 2
USB 3.2 Gen 1 5Gbps ports)
∙∙ 2x USB 2.0 connectors (supports additional 4 USB 2.0
ports)
Internal Connectors
∙∙ 1x 4-pin CPU fan connector
∙∙ 1x 4-pin water-pump fan connector
∙∙ 5x 4-pin system fan connectors
∙∙ 1x Front panel audio connector
∙∙ 2x System panel connectors
∙∙ 1x Chassis Intrusion connector
∙∙ 1x Clear CMOS jumper
∙∙ 1x TPM module connector
∙∙ 1x TBT connector (supports RTD3)
∙∙ 1x Tuning Controller connector

Continued on next column

Specifications 19
 Continued from previous column

∙∙ 1x EZ LED Control switch

∙∙ 2x 4-pin RGB LED connectors
LED Features
∙∙ 2x 3-pin RAINBOW LED connectors
∙∙ 4x EZ Debug LED

∙∙ 4x USB 2.0 Type-A ports

∙∙ 1x DisplayPort
∙∙ 1x HDMI port
∙∙ 4x USB 3.2 Gen 1 5Gbps Type-A ports
∙∙ 1x USB 3.2 Gen 2x2 20Gbps Type-C port
Back Panel
Connectors ∙∙ 1x 2.5G LAN (RJ45) port
∙∙ 1x 1G LAN (RJ45) port (For MAG B560 TORPEDO only)
∙∙ 2x Wi-Fi Antenna connectors (For MAG B560 TOMAHAWK
WIFI only)
∙∙ 5x audio jacks
∙∙ 1x Optical S/PDIF OUT connector

I/O Controller NUVOTON NCT6687-R Controller Chip

∙∙ CPU/ System/ Chipset temperature detection

Hardware Monitor ∙∙ CPU/ System/ Pump fan speed detection
∙∙ CPU/ System/ Pump fan speed control

∙∙ ATX Form Factor

Form Factor
∙∙ 12 in. x 9.6 in. (30.5 cm x 24.4 cm)

∙∙ 1x 256 Mb flash
∙∙ UEFI AMI BIOS
BIOS Features
∙∙ ACPI 6.2, SMBIOS 3.0
∙∙ Multi-language

Continued on next column

20 Specifications
 Continued from previous column

∙∙ Drivers
∙∙ MSI Center
∙∙ MSI APP Player (BlueStacks)
∙∙ Open Broadcaster Software (OBS)
Software
∙∙ CPU-Z MSI GAMING
∙∙ Intel® Extreme Tuning Utility
∙∙ Google Chrome™, Google Toolbar, Google Drive
∙∙ Norton™ Internet Security Solution

∙∙ MSI Sound Tune

∙∙ Gaming Mode
∙∙ Creator Mode
∙∙ Game Highlights
∙∙ LAN Manager
∙∙ Mystic Light

MSI Center ∙∙ Ambient Link

Features ∙∙ Frozr AI Cooling
∙∙ User Scenario
∙∙ True Color
∙∙ Live Update
∙∙ Monitor
∙∙ Super Charger
∙∙ Speed Up

Continued on next column

Specifications 21
 Continued from previous column

∙∙ Audio
▪▪Audio Boost
▪▪Sound Tune
∙∙ Network
▪▪2.5G LAN
▪▪LAN Manager
▪▪Intel Wi-Fi AX210 (For MAG B560 TOMAHAWK WIFI
only)
Special Features
∙∙ Cooling
▪▪All Aluminum Design
▪▪Extended Heatsink Design
▪▪M.2 Shield Frozr
▪▪K7 thermal pad
▪▪Choke pad
▪▪Pump Fan
▪▪Smart Fan Control

Continued on next column

22 Specifications
 Continued from previous column

∙∙ LED
▪▪Mystic Light
▪▪Mystic Light Extension (RAINBOW/RGB)
▪▪Mystic Light SYNC
▪▪Ambient Link (For MAG B560 TOMAHAWK WIFI only)
▪▪EZ LED Control
▪▪EZ DEBUG LED
∙∙ Performance
▪▪Lightning Gen 4 PCI-E Slot
▪▪Lightning Gen 4 M.2
▪▪Multi GPU-CrossFire Technology
▪▪DDR4 Boost
▪▪Core Boost
▪▪OC Engine
Special Features
▪▪Lightning USB 20G
▪▪USB 3.2 Gen 2 10G
▪▪USB with Type A+C
▪▪Front USB Type-C
▪▪Dual CPU Power
▪▪SUPPLEMENTAL PCIE POWER CONNECTOR
▪▪2oz Copper thickened PCB
∙∙ Protection
▪▪PCI-E Steel Armor
▪▪Pre-installed I/O Shielding
∙∙ Experience
▪▪MSI Center
▪▪Click BIOS 5
▪▪CPU Cooler Tuning

Specifications 23
 Package contents
Please check the contents of your motherboard package. It should contain:

Motherboard MAG B560 TOMAHAWK WIFI/ MAG B560 TORPEDO

User manual 1
Documentation Quick installation guide 1
MSI reward program card 1
Application Driver DVD 1
Cables SATA 6Gb/s cables (2 cables/pack) 1
Wi-Fi antenna (For MAG B560 TOMAHAWK WIFII
1
only)
Case badge 1

Accessories M.2 screw + standoff (2 sets/pack) 1

M.2 screw + standoff (1 set/pack) 1
MAG sticker 1
Product registration card 1

⚠⚠Important
If any of the above items are damaged or missing, please contact your retailer.

24 Package contents
Block Diagram

PCI_E1 CPU
PCIe x16

DDR4 2Channel
DIMM A1/A2
M2_1
DIMM B1/B2

DMI x8

PCI_E2
PCIe x4
PCH USB 3.2 Gen 2x2 20Gbps

USB 3.2 Gen 2 10Gbps

PCI_E3

SATA2 M2_2 USB 3.2 Gen 1 5Gbps

M2_3
USB 2.0

Intel LAN I219V/RTL8125B

USB 2.0
Hub-GL850G

WiFi AX210

SATA1/3/4/5/6
MCU

SPI
TPM

SIO 6687
HD Audio
ALC897

Block Diagram 25
 Rear I/O Panel
∙∙ MAG B560 TOMAHAWK WIFI
Wi-Fi Antenna
connectors
USB 2.0 Audio Ports
2.5Gbps
Type-A LAN
DisplayPort

USB 3.2 USB 3.2 Optical

Gen 1 Gen 2x2 S/PDIF-Out
(5Gbps) (20Gbps)
Type-A Type-C

∙∙ MAG B560 TORPEDO

USB 2.0 Audio Ports

2.5Gbps 1Gbps
Type-A LAN LAN
DisplayPort

USB 3.2 USB 3.2 Optical

Gen 1 Gen 2x2 S/PDIF-Out
(5Gbps) (20Gbps)
Type-A Type-C

26 Rear I/O Panel

LAN Port LED Status Table
Link/ Activity LED Speed LED

Status Description Status Description

Off No link Off 10 Mbps connection

Yellow Linked Green 100/1000 Mbps connection

Blinking Data activity Orange 1/2.5 Gbps connection

Audio Ports Configuration

Channel
Audio Ports
2 4 6 8

Center/ Sub-woofer Out ● ●

Rear Speaker Out ● ● ●

Line-In/ Side Speaker Out ●

Line-Out/ Front Speaker Out ● ● ● ●

Mic In

(●: connected, Blank: empty)

Realtek Audio Console

After Realtek Audio Console is installed. You can use it to change sound settings to get
better sound experience.
Application Enhancement

Device
Selection

Main Volume

Connector Settings Jack Status

Rear I/O Panel 27

 ∙∙ Device Selection - allows you to select a audio output source to change the related
options. The check sign indicates the devices as default.
∙∙ Application Enhancement - the array of options will provide you a complete
guidance of anticipated sound effect for both output and input device.
∙∙ Main Volume - controls the volume or balance the right/left side of the speakers
that you plugged in front or rear panel by adjust the bar.
∙∙ Jack Status - depicts all render and capture devices currently connected with your
computer.
∙∙ Connector Settings - configures the connection settings.

Auto popup dialog

When you plug into a device at an audio jack, a dialogue window will pop up asking you
which device is current connected.

Each jack corresponds to its default setting as shown on the next page.

⚠⚠Important
The pictures above for reference only and may vary from the product you purchased.

28 Rear I/O Panel

Audio jacks to headphone and microphone diagram

Audio jacks to stereo speakers diagram

AUDIO INPUT

Audio jacks to 7.1-channel speakers diagram

AUDIO INPUT

Rear Front

Side Center/
Subwoofer

Rear I/O Panel 29

 Installing antennas
1. Screw the antennas tight to the antenna connectors as shown below.
2. Orient the antennas.

30 Rear I/O Panel

Overview of Components

CPU_PWR2 CPU_FAN1

CPU_PWR1 Processor Socket JRAINBOW1

JRGB2

PUMP_FAN1

ATX_PWR1

JUSB3

JUSB4
M2_1
SYS_FAN1 DIMMB2
DIMMB1
PCI_E1 DIMMA2
DIMMA1

BAT1

M2_2
JBAT1
SATA▼1▲2
PCI_E2
M2_3 SATA▼3▲4

JDASH1 SYS_FAN4
PCI_E3 JTPM1
JCI1

JAUD1 SYS_FAN5
JRGB1 JFP1
JRAINBOW2 JFP2
SYS_FAN2 SATA6
SYS_FAN3 SATA5
LED_SW1 JUSB1

PCIE_PWR1 JUSB2
JTBT1

Overview of Components 31
 Component Contents

Port Name Port Type Page

CPU_FAN1, PUMP_FAN1,
Fan Connectors 43
SYS_FAN1~5

CPU_PWR1~2, ATX_PWR1,
Power Connectors 40
PCIE_PWR1

CPU Socket LGA1200 CPU Socket 33

DIMM Slots Memory slots 34

JAUD1 Front Audio Connector 35

JBAT1 Clear CMOS (Reset BIOS) Jumper 45

JCI1 Chassis Intrusion Connector 44

JDASH1 Tuning Controller connector 45

JFP1, JFP2 Front Panel Connectors 39

JRAINBOW1~2 Addressable RGB LED connectors 47

JRGB1~2 RGB LED connectors 46

JTBT1 Thunderbolt Add-on Card Connector 42

JTPM1 TPM Module Connector 39

JUSB1~2 USB 2.0 Connectors 42

JUSB3 USB 3.2 Gen 1 Connector 41

JUSB4 USB 3.2 Gen 2 Type-C Connector 41

LED_SW1 EZ LED Control 48

M2_1~3 M.2 Slots (Key M) 36

PCI_E1~3 PCIe Expansion Slots 35

SATA1~6 SATA 6Gb/s Connectors 38

32 Overview of Components
CPU Socket

Distance from the center of the

CPU to the nearest DIMM slot.

50.6 mm

Introduction to the LGA1200 CPU

The surface of the LGA1200 CPU has
two notches and a golden triangle to
assist in correctly lining up the CPU for
motherboard placement. The golden
triangle is the Pin 1 indicator.

⚠⚠Important
∙∙ Always unplug the power cord from the power outlet before installing or removing
the CPU.
∙∙ Please retain the CPU protective cap after installing the processor. MSI will deal
with Return Merchandise Authorization (RMA) requests if only the motherboard comes
with the protective cap on the CPU socket.
∙∙ When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink
is necessary to prevent overheating and maintain system stability.
∙∙ Confirm that the CPU heatsink has formed a tight seal with the CPU before booting
your system.
∙∙ Overheating can seriously damage the CPU and motherboard. Always make sure
the cooling fans work properly to protect the CPU from overheating. Be sure to apply
an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to
enhance heat dissipation.
∙∙ Whenever the CPU is not installed, always protect the CPU socket pins by covering
the socket with the plastic cap.
∙∙ If you purchased a separate CPU and heatsink/ cooler, Please refer to the
documentation in the heatsink/ cooler package for more details about installation.
∙∙ This motherboard is designed to support overclocking. Before attempting to
overclock, please make sure that all other system components can tolerate
overclocking. Any attempt to operate beyond product specifications is not
recommended. MSI® does not guarantee the damages or risks caused by inadequate
operation beyond product specifications.

Overview of Components 33
 DIMM Slots

DIMMA1 DIMMB1

Channel A Channel B

DIMMA2 DIMMB2

Memory module installation recommendation

DIMMA1
DIMMA2 DIMMA2
DIMMA2
DIMMB1
DIMMB2 DIMMB2

⚠⚠Important
∙∙ Always insert memory modules in the DIMMA2 slot first.
∙∙ To ensure system stability for Dual channel mode, memory modules must be of the
same type, number and density.
∙∙ Some memory modules may operate at a lower frequency than the marked value
when overclocking due to the memory frequency operates dependent on its Serial
Presence Detect (SPD). Go to BIOS and find the DRAM Frequency to set the memory
frequency if you want to operate the memory at the marked or at a higher frequency.
∙∙ It is recommended to use a more efficient memory cooling system for full DIMMs
installation or overclocking.
∙∙ The stability and compatibility of installed memory module depend on installed CPU
and devices when overclocking.
∙∙ Please refer to www.msi.com for more information on compatible memory.

34 Overview of Components
 PCI_E1~3: PCIe Expansion Slots

PCI_E1: PCIe 4.0 x16 (From CPU)

BAT1

PCI_E2: PCIe 3.0 x4 (From B560 chipset)

PCI_E3: PCIe 3.0 x1 (From B560 chipset)

⚠⚠Important
∙∙ If you install a large and heavy graphics card, you need to use a tool such as MSI
Graphics Card Bolster to support its weight to prevent deformation of the slot.
∙∙ For a single PCIe x16 expansion card installation with optimum performance, using
the PCI_E1 slot is recommended.
∙∙ When adding or removing expansion cards, always turn off the power supply and
unplug the power supply power cable from the power outlet. Read the expansion
card’s documentation to check for any necessary additional hardware or software
changes.

JAUD1: Front Audio Connector

This connector allows you to connect audio jacks on the front panel.

2 10

1 9

1 MIC L 2 Ground

3 MIC R 4 NC

5 Head Phone R 6 MIC Detection

7 SENSE_SEND 8 No Pin

9 Head Phone L 10 Head Phone Detection

Overview of Components 35
 M2_1~3: M.2 Slots (Key M)

⚽⚽Video Demonstration
Watch the video to learn how to Install
M.2 SSD.
https://youtu.be/2UeWMgjwogU
M2_1

M2_2

M2_3

⚠⚠Important
∙∙ Intel® RST only supports PCIe M.2 SSD with UEFI ROM.
∙∙ Intel® Optane™ Memory Ready for M2_3 slot only.

Installing M.2 module

1. Loosen the screws of M.2 SHIELD FROZR heatsink.
2. Remove the M.2 SHIELD FROZR and remove the protective films from the thermal
pads.

1
M2_1

1
M2_2
1

36 Overview of Components
3. Secure the supplied M.2 standoff according to your M.2 SSD length if need.
4. Insert your M.2 SSD into the M.2 slot at a 30-degree angle.
5. Secure the M.2 SSD in place with the supplied M.2 8.5H screw.

⚠⚠Important
∙∙ M.2 SHIELD FROZR heatsink for M2_1 slot is only avaliable for MAG B560
TOMAHAWK WIFI.
∙∙ Skip step 3 and step 5, if you install 22110 M.2 into M2_1 slot or 2280 M.2 into M2_2
slots.

8.5H screw 30º

5
Standoff

6. Put the M.2 SHIELD FROZR heatsink back in place and secure it.

6
6

Overview of Components 37
 SATA1~6: SATA 6Gb/s Connectors
These connectors are SATA 6Gb/s interface ports. Each connector can connect to one
SATA device.

SATA2
SATA1
SATA4
SATA3

SATA5

SATA6

⚠⚠Important
∙∙ Please do not fold the SATA cable at a 90-degree angle. Data loss may result during
transmission otherwise.
∙∙ SATA cables have identical plugs on either sides of the cable. However, it is
recommended that the flat connector be connected to the motherboard for space
saving purposes.
∙∙ SATA2 will be unavailable when installing M.2 SATA SSD in the M2_2 slot.

M.2 & SATA combination table

Slot Available SATA connectors

M2_1 PCIe (M2_1 slot is only available on 11th Gen Intel® CPU)
M2_2 PCIe SATA
M2_3 PCIe (M2_3 slot does not support SATA)
SATA1 ✓ ✓
SATA2 ✓ ─
SATA3 ✓ ✓
SATA4 ✓ ✓
SATA5 ✓ ✓
SATA6 ✓ ✓
(SATA: M.2 SATA SSD, PCIe: M.2 PCIe SSD, ✓: available, ─: unavailable)

38 Overview of Components
JFP1, JFP2: Front Panel Connectors
These connectors connect to the switches and LEDs on the front panel.

Buzzer

+
-
JFP2 1

Speaker

+
-
1 Speaker - 2 Buzzer +

3 Buzzer - 4 Speaker +

Power LED Power Switch

+
+
2 10

-
-
JFP1
1 9
Reserved
+

+
-
-
HDD LED Reset Switch
1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

JTPM1: TPM Module Connector

This connector is for TPM (Trusted Platform Module). Please refer to the TPM security
platform manual for more details and usages.

2 12

1 11

1 SPI Power 2 SPI Chip Select

Master Out Slave In (SPI

3 Master In Slave Out (SPI Data) 4
Data)

5 Reserved 6 SPI Clock

7 Ground 8 SPI Reset

9 Reserved 10 No Pin

11 Reserved 12 Interrupt Request

Overview of Components 39
 CPU_PWR1~2, ATX_PWR1, PCIE_PWR1: Power Connectors
These connectors allow you to connect an ATX power supply.

8 5
CPU_PWR1
4 1

1 Ground 5 +12V

2 Ground 6 +12V

3 Ground 7 +12V

4 Ground 8 +12V

4 3
CPU_PWR2
2 1

1 Ground 3 +12V

2 Ground 4 +12V

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 Ground 15 Ground

12 24 4 +5V 16 PS-ON#

5 Ground 17 Ground

6 +5V 18 Ground
ATX_PWR1
7 Ground 19 Ground

8 PWR OK 20 Res

1 13 9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 Ground

1 3 1 +12V 4 Ground
PCIE_PWR1 2 +12V 5 Ground
4 6 3 +12V 6 Ground

⚠⚠Important
Make sure that all the power cables are securely connected to a proper ATX power
supply to ensure stable operation of the motherboard.

40 Overview of Components
JUSB4: USB 3.2 Gen 2 Type-C Connector
This connector allows you to connect USB 3.2 Gen 2 Type-C connector on the front
panel. The connector possesses a foolproof design. When you connect the cable, be
sure to connect it with the corresponding orientation.

USB Type-C Cable

JUSB4

USB Type-C port on

the front panel

JUSB3: USB 3.2 Gen 1 Connector

This connector allows you to connect USB 3.2 Gen 1 5Gbps ports on the front panel.

10 11

1 20

1 Power 11 USB2.0+

2 USB3_RX_DN 12 USB2.0-

3 USB3_RX_DP 13 Ground

4 Ground 14 USB3_TX_C_DP

5 USB3_TX_C_DN 15 USB3_TX_C_DN

6 USB3_TX_C_DP 16 Ground

7 Ground 17 USB3_RX_DP

8 USB2.0- 18 USB3_RX_DN

9 USB2.0+ 19 Power

10 Ground 20 No Pin

⚠⚠Important
Note that the Power and Ground pins must be connected correctly to avoid possible
damage.

Overview of Components 41
 JUSB1~2: USB 2.0 Connectors
These connectors allow you to connect USB 2.0 ports on the front panel.

2 10

1 9

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 Ground 8 Ground

9 No Pin 10 NC

⚠⚠Important
∙∙ Note that the VCC and Ground pins must be connected correctly to avoid possible
damage.
∙∙ In order to recharge your iPad, iPhone and iPod through USB ports, please install
MSI® Center utility.

JTBT1: Thunderbolt Add-on Card Connector

This connector allows you to connect the add-on Thunderbolt I/O card.

2 16

1 15

1 TBT_FORCE_PWR 2 TBT_S0IX_ENTRY_REQ

3 TBT_CIO_PLUG_EVENT# 4 TBT_S0IX_ENTRY_ACK

5 SLP_S3#_TBT 6 TBT_PSON_OVERRIDE_N

7 SLP_S5#_TBT 8 No Pin

9 Ground 10 SMBCLK_VSB

11 DG_PEWAKE# 12 SMBDATA_VSB

13 TBT_RTD3_PWR_EN 14 Ground

15 TBT_CARD_DET_R# 16 PD_IRQ#

42 Overview of Components
CPU_FAN1, PUMP_FAN1, SYS_FAN1~5: Fan Connectors
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode.
PWM Mode fan connectors provide constant 12V output and adjust fan speed with
speed control signal. DC Mode fan connectors control fan speed by changing voltage.
The auto mode fan connectors can automatically detect PWM and DC mode. However,
you can follow the instruction below to adjust the fan connector to PWM or DC Mode
manually.
SYS_FAN1 CPU_FAN1
PUMP_FAN1

Default fan Max. Max.

Connector
mode current power
CPU_FAN1 PWM mode 2A 24W

PUMP_FAN1 PWM mode 3A 36W

SYS_FAN1~5 DC mode 1A 12W

SYS_FAN4

SYS_FAN2 SYS_FAN3 SYS_FAN5

Switching fan mode and adjusting fan speed

You can switch between PWM mode and DC mode and adjust fan speed in BIOS >
HARDWARE MONITOR.
Select PWM mode or DC mode

There are gradient points of the fan speed that allow you to adjust
fan speed in relation to CPU temperature.

⚠⚠Important
Make sure fans are working properly after switching the PWM/ DC mode.

Pin definition of fan connectors

1 1
PWM Mode pin definition DC Mode pin definition

1 Ground 2 +12V 1 Ground 2 Voltage Control

3 Sense 4 Speed Control Signal 3 Sense 4 NC

Overview of Components 43
 JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.

Normal Trigger the chassis

(default) intrusion event

Using chassis intrusion detector

1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.
2. Close the chassis cover.
3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.
4. Set Chassis Intrusion to Enabled.
5. Press F10 to save and exit and then press the Enter key to select Yes.
6. Once the chassis cover is opened again, a warning message will be displayed on
screen when the computer is turned on.

Resetting the chassis intrusion warning

1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.
2. Set Chassis Intrusion to Reset.
3. Press F10 to save and exit and then press the Enter key to select Yes.

44 Overview of Components
JBAT1: Clear CMOS (Reset BIOS) Jumper
There is CMOS memory onboard that is external powered from a battery located on
the motherboard to save system configuration data. If you want to clear the system
configuration, set the jumpers to clear the CMOS memory.

Keep Data Clear CMOS/

(default) Reset BIOS

Resetting BIOS to default values

1. Power off the computer and unplug the power cord.
2. Use a jumper cap to short JBAT1 for about 5-10 seconds.
3. Remove the jumper cap from JBAT1.
4. Plug the power cord and Power on the computer.

JDASH1 : Tuning Controller connector

This connector is used to connect an optional Tuning Controller module.

2 6

1 5

1 No Pin 2 NC

3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M

5 VCC5 6 Ground

Overview of Components 45
 JRGB1~2: RGB LED connectors
The JRGB connectors allow you to connect the 5050 RGB LED strips 12V.

1 +12V 2 G

3 R 4 B

RGB LED Strip Connection

1
G R B

RGB extension
JRGB cable 5050 RGB LED strips 12V
connector

RGB LED Fan Connection

JRGB connector

1
G R B

RGB LED Fan

System Fan connector

⚠⚠Important
∙∙ The JRGB connector supports up to 2 meters continuous 5050 RGB LED strips
(12V/G/R/B) with the maximum power rating of 3A (12V).
∙∙ Always turn off the power supply and unplug the power cord from the power outlet
before installing or removing the RGB LED strip.
∙∙ Please use MSI’s software to control the extended LED strip.

46 Overview of Components
JRAINBOW1~2: Addressable RGB LED connectors
The JRAINBOW connectors allow you to connect the WS2812B Individually
Addressable RGB LED strips 5V.

1 +5V 2 Data

3 No Pin 4 Ground

Addressable RGB LED Strip Connection

1
+5V
D

JRAINBOW Rainbow RGB LED

connector extension cable WS2812B Individually
Addressable RGB LED strips 5V

Addressable RGB LED Fan Connection

JRAINBOW connector

Addressable RGB LED Fan

System Fan connector

⚠⚠CAUTION
Do not connect the wrong type of LED strips. The JRGB connector and the JRAINBOW
connector provide different voltages, and connecting the 5V LED strip to the JRGB
connector will result in damage to the LED strip.

⚠⚠Important
∙∙ The JRAINBOW connector supports up to 75 LEDs WS2812B Individually
Addressable RGB LED strips (5V/Data/Ground) with the maximum power rating of 3A
(5V). In the case of 20% brightness, the connector supports up to 200 LEDs.
∙∙ Always turn off the power supply and unplug the power cord from the power outlet
before installing or removing the RGB LED strip.
∙∙ Please use MSI’s software to control the extended LED strip.

Overview of Components 47
 Onboard LEDs
EZ Debug LED
These LEDs indicate the debug status of the motherboard.

CPU - indicates CPU is not detected or fail.

DRAM - indicates DRAM is not detected or fail.
VGA - indicates GPU is not detected or fail.
BOOT - indicates the booting device is not detected
or fail.

LED_SW1: EZ LED Control

This switch is used to switch on/ off all the LEDs of motherboard.

LED_OFF LED_ON
(Default)

LED_SW1

48 Onboard LEDs
Installing OS, Drivers & MSI Center
Please download and update the latest utilities and drivers at www.msi.com

Installing Windows® 10
1. Power on the computer.
2. Insert the Windows® 10 installation disc/USB into your computer.
3. Press the Restart button on the computer case.
4. Press F11 key during the computer POST (Power-On Self Test) to get into Boot
Menu.
5. Select the Windows® 10 installation disc/USB from the Boot Menu.
6. Press any key when screen shows Press any key to boot from CD or DVD...
message.
7. Follow the instructions on the screen to install Windows® 10.

Installing Drivers
1. Start up your computer in Windows® 10.
2. Insert MSI® USB Drive into the USB port.
3. Click the Select to choose what happens with this disc pop-up notification, then
select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature
from the Windows Control Panel, you can still manually execute the DVDSetup.exe
from the root path of the MSI USB Drive.
4. The installer will find and list all necessary drivers in the Drivers/Software tab.
5. Click the Install button in the lower-right corner of the window.
6. The drivers installation will then be in progress, after it has finished it will prompt
you to restart.
7. Click OK button to finish.
8. Restart your computer.

MSI Center
MSI Center is an application that helps you easily optimize game settings and smoothly
use content creation softwares. It also allows you to control and synchronize LED
light effects on PCs and other MSI products. With MSI Center, you can customize ideal
modes, monitor system performance, and adjust fan speed.

MSI Center User Guide

If you would like to know more information about MSI Center, please
refer to
http://download.msi.com/manual/mb/MSICENTER.pdf
or scan the QR code to access.

⚠⚠Important
Functions may vary depending on the product you have.

Installing OS, Drivers & MSI Center 49

 UEFI BIOS
MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface)
architecture. The UEFI BIOS firmware infrastructure has many new functions and
advantages that traditional BIOS cannot achieve. It will fully support future PCs and
devices that comply with UEFI firmware architecture.

⚠⚠Important
The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.

UEFI advantages
∙∙ Fast booting - UEFI can directly boot the operating system and save the BIOS self-
test process. And also eliminates the time to switch to CSM mode during POST
∙∙ Supports for hard drive partitions larger than 2 TB.
∙∙ Supports more than 4 primary partitions with a GUID Partition Table (GPT).
∙∙ Supports unlimited number of partitions
∙∙ Supports full capabilities of new devices - new devices may not provide backward
compatibility.
∙∙ Supports secure startup - UEFI can check the validity of the operating system to
ensure that no malware tampers with the startup process.

Incompatible UEFI cases

∙∙ 32-bit Windows operating system - this motherboard supports only 64-bit Windows
10 operating system.
∙∙ Older graphics card - the system will detect your graphics card. When display a
warning message There is no GOP (Graphics Output protocol) support detected in
this graphics card.

⚠⚠Important
We recommend that you to replace with a GOP/UEFI compatible graphics card or
using integrated graphics from CPU for having normal function.

How to check the BIOS mode?

1. Power on your computer.
2. Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter
Boot Menu message appears on the screen during the boot process.
3. After entering the BIOS, you can check the BIOS Mode at the top of the screen.

BIOS Mode: UEFI

50 UEFI BIOS
BIOS Setup
The default settings offer the optimal performance for system stability in normal
conditions. You should always keep the default settings to avoid possible system
damage or failure booting unless you are familiar with BIOS.

⚠⚠Important
∙∙ BIOS items are continuously updated for better system performance. Therefore, the
description may be slightly different from the latest BIOS and should be for reference
only. You could also refer to the HELP information panel for BIOS item description.
∙∙ The BIOS screens, options and settings will vary depending on your system.

Entering BIOS Setup

Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot
Menu message appears on the screen during the boot process.

Function key
F1: General Help list
F2: Add/ Remove a favorite item
F3: Enter Favorites menu
F4: Enter CPU Specifications menu
F5: Enter Memory-Z menu
F6: Load optimized defaults
F7: Switch between Advanced mode and EZ mode
F8: Load Overclocking Profile
F9: Save Overclocking Profile
F10: Save Change and Reset*
F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only).
Ctrl+F: Enter Search page
* When you press F10, a confirmation window appears and it provides the modification
information. Select between Yes or No to confirm your choice.

BIOS User Guide

If you’d like to know more instructions on setting up the BIOS, please
refer to
http://download.msi.com/manual/mb/Intel500BIOS.pdf
or scan the QR code to access.

UEFI BIOS 51
 Resetting BIOS
You might need to restore the default BIOS setting to solve certain problems. There
are several ways to reset BIOS:
∙∙ Go to BIOS and press F6 to load optimized defaults.
∙∙ Short the Clear CMOS jumper on the motherboard.

⚠⚠Important
Be sure the computer is off before clearing CMOS data. Please refer to the Clear
CMOS jumper/ button section for resetting BIOS.

Updating BIOS
Updating BIOS with M-FLASH
Before updating:
Please download the latest BIOS file that matches your motherboard model from MSI
website. And then save the BIOS file into the USB flash drive.
To update BIOS:
1. Insert the USB flash drive that contains the update file into the USB port.
2. Please refer the following methods to enter flash mode.
▪▪Reboot and press Ctrl + F5 key during POST and click on Yes to reboot the
system.

Press <Ctrl+F5> to activate M-Flash for BIOS update.

▪▪Reboot and press Del key during POST to enter BIOS. Click the M-FLASH button
and click on Yes to reboot the system.

3. Select a BIOS file to perform the BIOS update process.

4. When prompted click on Yes to start recovering BIOS.
5. After the flashing process is 100% completed, the system will reboot
automatically.

52 UEFI BIOS
Updating the BIOS with MSI Center
Before updating:
∙∙ Make sure the LAN driver is already installed and the internet connection is set
properly.
∙∙ Please close all other application software before updating the BIOS.
To update BIOS:
1. Install and launch MSI CENTER and go to Support page.
2. Select Live Update and click on the Advanced button.
3. Select the BIOS file and click on the Install button.
4. The installation reminder will appear, then click the Install button on it.
5. The system will automatically restart to update BIOS.
6. After the flashing BIOS process is 100% completed, the system will restart
automatically.

UEFI BIOS 53
 Intel® Optane™ Memory Configuration
Intel® Optane™ memory is a technology which allows the system to access the data
more quickly. It enables the computer to store commonly used data and programs,
and keeps them even after powering off the computer. Before you start to install Intel®
Optane™ memory, please note that it requires Windows 10 64-bit operating system.

Intel® Optane™ Memory User Guide

If you’d like to know more instructions on how to enable or remove
Intel® Optane™ Memory, please refer to
http://download.msi.com/manual/mb/Optane.pdf
or scan the QR code to access.

⚠⚠WARNING
After you enable Intel® Optane™ memory, please note the following to prevent damage
to your operating system.
∙∙ DO NOT set the SATA mode back to AHCI in BIOS.
∙∙ DO NOT revert back to older version of the BIOS.
∙∙ DO NOT remove the Intel® Optane™ memory module.
∙∙ DO NOT replace the CPU that is not supported by Intel® Optane™ Memory.

54 Intel® Optane™ Memory Configuration

Troubleshooting
Before sending the motherboard for RMA Lost BIOS password
repair, try to go over troubleshooting
guide first to see if your got similar ∙∙ Clear the CMOS, but that will cause
symptoms as mentioned below. you to lose all customized settings in the
BIOS.
The power is not on.
There is no audio
∙∙ Connect the AC power cord to an
electrical outlet securely. ∙∙ Adjust the volume.

∙∙ Check if all ATX power connectors ∙∙ Connect the speakers/headphones to

like ATX_PWR1, CPU_PWR1 are audio ports on the motherboard rear IO
connected from the power supply to the panel.
motherboard? ∙∙ Remove secondary speakers/
∙∙ Some power supply units have a power headphones, HDMI cables, USB audio
button on the rear side, make sure the devices.
button is turned on. ∙∙ Test with another known working
∙∙ Check if the power switch cable is speaker or headphone.
connected to JFP1 pin header properly.
There is no network
∙∙ Verify the Clear CMOS jumper JBAT1 is
set to Keep DATA. ∙∙ Make sure the network chipset driver
has been installed.
∙∙ Test with another known working
power supply of equal or greater ∙∙ Verify if the network cable is properly
wattage. connected and make sure the LAN port
LEDs are properly illuminated.
The power is on, but no signal to ∙∙ Verify your TCP/IP settings.
monitor
∙∙ Restart or reset your router.
∙∙ Connect the monitor power cord to a
electrical outlet securely. ∙∙ Test with another known working LAN
cable.
∙∙ Make sure the monitor is turned on.
∙∙ Select different inputs on the monitor. The USB device is not working
∙∙ If 3 long beeps are heard, remove all ∙∙ Make sure your USB drive driver has
memory modules and try to install only been installed.
one memory module in the DIMMA2 slot
first and then restart the computer. ∙∙ Verify if USB device is listed in
Windows® Device Manager.
∙∙ If 1 long 2 short beeps are heard,
remove and reinstall the graphics card ∙∙ Connect the USB device to other USB
and then restart the computer. port on the motherboard rear IO panel.

∙∙ Test with another known working

graphics card.

The computer does not boot after

updating the BIOS
∙∙ Clear the CMOS.
∙∙ Use the secondary BIOS to bootup the
system (Only for motherboard with Dual
BIOS)

Troubleshooting 55
 NOTE

56 Troubleshooting
Regulatory Notices クラスB情報技術装置
この装置は、クラスＢ情報技術装置です。この
FCC Compliance Statement
装置は、家庭環境で使用することを目的とし
ていますが、この装置がラジオやテレビジョン
Note: This equipment has been tested and found to 受信機に近接して使用されると、受信障害を引き起こす
comply with the limits for a Class B digital device, ことがあります。取扱説明書に従って正しい取り扱いを
pursuant to part 15 of the FCC Rules. These limits are して下さい。
designed to provide reasonable protection against VCCI-B
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio C-Tick Compliance
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
Battery Information
which can be determined by turning the equipment European Union:
off and on, the user is encouraged to try to correct the Batteries, battery packs, and
interference by one or more of the following measures: accumulators should not be disposed of as
unsorted household waste. Please use the
yy Reorient or relocate the receiving antenna.
public collection system to return, recycle,
yy Increase the separation between the equipment or treat them in compliance with the local
and receiver. regulations.
yy Connect the equipment into an outlet on a circuit Taiwan:
different from that to which the receiver is 廢電池請回收
connected. For better environmental protection,
yy Consult the dealer or an experienced radio/TV waste batteries should be collected
technician for help. separately for recycling or special
disposal.
Caution: Changes or modifications not expressly
approved by the party responsible for compliance could California, USA:
void the user’s authority to operate the equipment. The button cell battery may contain
perchlorate material and requires special
Tested to comply with FCC standards handling when recycled or disposed of in
FOR HOME OR OFFICE USE California.
For further information please visit:
This device complies with part 15 of the FCC Rules. http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, CAUTION: There is a risk of explosion, if battery is
and (2) this device must accept any interference incorrectly replaced.
received, including interference that may cause
Replace only with the same or equivalent type
undesired operation.
recommended by the manufacturer.
CE Conformity Chemical Substances Information
Products bearing the CE marking comply
In compliance with chemical substances regulations,
with one or more of the following EU
such as the EU REACH Regulation (Regulation EC
Directives as may be applicable:
No. 1907/2006 of the European Parliament and the
RED 2014/53/EU; Low Voltage Directive 2014/35/EU; Council), MSI provides the information of chemical
EMC Directive 2014/30/EU; RoHS Directive 2011/65/EU. substances in products at:
Compliance with these directives is assessed using https://storage-asset.msi.com/html/popup/csr/
applicable European Harmonized Standards. evmtprtt_pcm.html

Environmental Policy
The point of contact for regulatory matters is MSI,
MSI-NL Eindhoven 5706 5692 ER Son.
yy The product has been designed to
KC인증서 enable proper reuse of parts and
yy MAG B560 TOMAHAWK WIFI recycling and should not be thrown
away at its end of life.
상호: (주)엠에스아이코리아
제품명: 메인보드 yy Users should contact the local
모델명: 10-7D15 authorized point of collection
제조년월: 2021년 for recycling and disposing of their end-of-life
R-R-MSI-10-7D15 제조자 및 제조국가: MSI/중국 products.
yy MAG B560 TORPEDO yy Visit the MSI website and locate a nearby distributor
for further recycling information.
상호: (주)엠에스아이코리아
제품명: 메인보드 yy Users may also reach us at gpcontdev@msi.com for
모델명: 20-7D15 information regarding proper Disposal, Take-back,
제조년월: 2021년 Recycling, and Disassembly of MSI products.
R-R-MSI-20-7D15 제조자 및 제조국가: MSI/중국

Regulatory Notices i
 WEEE (Waste Electrical and del medio ambiente, recomienda:
Electronic Equipment) Bajo la directiva 2002/96/EC de la Unión Europea
Statement en materia de desechos y/o equipos electrónicos,
con fecha de rigor desde el 13 de agosto de 2005,
ENGLISH los productos clasificados como “eléctricos y
To protect the global environment equipos electrónicos” no pueden ser depositados
and as an environmentalist, MSI must en los contenedores habituales de su municipio, los
remind you that... fabricantes de equipos electrónicos, están obligados
Under the European Union (“EU”) a hacerse cargo de dichos productos al termino de
Directive on Waste Electrical and Electronic su período de vida. MSI estará comprometido con los
Equipment, Directive 2002/96/EC, which takes effect on términos de recogida de sus productos vendidos en
August 13, 2005, products of “electrical and electronic la Unión Europea al final de su periodo de vida. Usted
equipment” cannot be discarded as municipal wastes debe depositar estos productos en el punto limpio
anymore, and manufacturers of covered electronic establecido por el ayuntamiento de su localidad o
equipment will be obligated to take back such products entregar a una empresa autorizada para la recogida de
at the end of their useful life. MSI will comply with the estos residuos.
product take back requirements at the end of life of NEDERLANDS
MSI-branded products that are sold into the EU. You Om het milieu te beschermen, wil MSI u eraan
can return these products to local collection points. herinneren dat….
DEUTSCH De richtlijn van de Europese Unie (EU) met betrekking
Hinweis von MSI zur Erhaltung und Schutz unserer tot Vervuiling van Electrische en Electronische
UmweltGemäß der Richtlinie 2002/96/EG über producten (2002/96/EC), die op 13 Augustus 2005 in
Elektro- und Elektronik-Altgeräte dürfen Elektro- zal gaan kunnen niet meer beschouwd worden als
und Elektronik-Altgeräte nicht mehr als kommunale vervuiling. Fabrikanten van dit soort producten worden
Abfälle entsorgt werden. MSI hat europaweit verplicht om producten retour te nemen aan het
verschiedene Sammel- und Recyclingunternehmen eind van hun levenscyclus. MSI zal overeenkomstig
beauftragt, die in die Europäische Union in Verkehr de richtlijn handelen voor de producten die de
gebrachten Produkte, am Ende seines Lebenszyklus merknaam MSI dragen en verkocht zijn in de EU. Deze
zurückzunehmen. Bitte entsorgen Sie dieses Produkt goederen kunnen geretourneerd worden op lokale
zum gegebenen Zeitpunkt ausschliesslich an einer inzamelingspunten.
lokalen Altgerätesammelstelle in Ihrer Nähe. SRPSKI
FRANÇAIS Da bi zaštitili prirodnu sredinu, i kao preduzeće koje
En tant qu’écologiste et afin de protéger vodi računa o okolini i prirodnoj sredini, MSI mora da
l’environnement, MSI tient à rappeler ceci... vas podesti da…
Au sujet de la directive européenne (EU) relative aux Po Direktivi Evropske unije (“EU”) o odbačenoj
déchets des équipement électriques et électroniques, ekektronskoj i električnoj opremi, Direktiva 2002/96/
directive 2002/96/EC, prenant effet le 13 août 2005, que EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi
les produits électriques et électroniques ne peuvent koji spadaju pod “elektronsku i električnu opremu” ne
être déposés dans les décharges ou tout simplement mogu više biti odbačeni kao običan otpad i proizvođači
mis à la poubelle. Les fabricants de ces équipements ove opreme biće prinuđeni da uzmu natrag ove
seront obligés de récupérer certains produits en fin proizvode na kraju njihovog uobičajenog veka trajanja.
de vie. MSI prendra en compte cette exigence relative MSI će poštovati zahtev o preuzimanju ovakvih
au retour des produits en fin de vie au sein de la proizvoda kojima je istekao vek trajanja, koji imaju MSI
communauté européenne. Par conséquent vous pouvez oznaku i koji su prodati u EU. Ove proizvode možete
retourner localement ces matériels dans les points vratiti na lokalnim mestima za prikupljanje.
de collecte. POLSKI
РУССКИЙ Aby chronić nasze środowisko naturalne oraz jako
Компания MSI предпринимает активные действия firma dbająca o ekologię, MSI przypomina, że...
по защите окружающей среды, поэтому напоминаем Zgodnie z Dyrektywą Unii Europejskiej (“UE”) dotyczącą
вам, что.... odpadów produktów elektrycznych i elektronicznych
В соответствии с директивой Европейского (Dyrektywa 2002/96/EC), która wchodzi w życie 13
Союза (ЕС) по предотвращению загрязнения sierpnia 2005, tzw. “produkty oraz wyposażenie
окружающей среды использованным электрическим elektryczne i elektroniczne “ nie mogą być traktowane
и электронным оборудованием (директива jako śmieci komunalne, tak więc producenci tych
WEEE 2002/96/EC), вступающей в силу 13 produktów będą zobowiązani do odbierania ich w
августа 2005 года, изделия, относящиеся к momencie gdy produkt jest wycofywany z użycia.
электрическому и электронному оборудованию, MSI wypełni wymagania UE, przyjmując produkty
не могут рассматриваться как бытовой мусор, (sprzedawane na terenie Unii Europejskiej) wycofywane
поэтому производители вышеперечисленного z użycia. Produkty MSI będzie można zwracać w
электронного оборудования обязаны принимать wyznaczonych punktach zbiorczych.
его для переработки по окончании срока TÜRKÇE
службы. MSI обязуется соблюдать требования по Çevreci özelliğiyle bilinen MSI dünyada çevreyi
приему продукции, проданной под маркой MSI korumak için hatırlatır:
на территории EC, в переработку по окончании Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik
срока службы. Вы можете вернуть эти изделия в Malzeme Atığı, 2002/96/EC Kararnamesi altında 13
специализированные пункты приема. Ağustos 2005 tarihinden itibaren geçerli olmak üzere,
ESPAÑOL elektrikli ve elektronik malzemeler diğer atıklar
MSI como empresa comprometida con la protección gibi çöpe atılamayacak ve bu elektonik cihazların

ii Regulatory Notices
üreticileri, cihazların kullanım süreleri bittikten sonra Türkiye EEE yönetmeliği
ürünleri geri toplamakla yükümlü olacaktır. Avrupa Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
Birliği’ne satılan MSI markalı ürünlerin kullanım
süreleri bittiğinde MSI ürünlerin geri alınması isteği ile Україна обмеження на наявність
işbirliği içerisinde olacaktır. Ürünlerinizi yerel toplama
noktalarına bırakabilirsiniz.
небезпечних речовин
Обладнання відповідає вимогам Технічного
ČESKY
регламенту щодо обмеження використання
Záleží nám na ochraně životního prostředí - společnost
деяких небезпечних речовин в електричному та
MSI upozorňuje...
електронному обладнані, затвердженого постановою
Podle směrnice Evropské unie (“EU”) o likvidaci
Кабінету Міністрів України від 3 грудня 2008 № 1057.
elektrických a elektronických výrobků 2002/96/
EC platné od 13. srpna 2005 je zakázáno likvidovat
“elektrické a elektronické výrobky” v běžném
Việt Nam RoHS
komunálním odpadu a výrobci elektronických Kể từ ngày 01/12/2012, tất cả các sản phẩm do công
výrobků, na které se tato směrnice vztahuje, budou ty MSI sản xuất tuân thủ Thông tư số 30/2011/TT-BCT
povinni odebírat takové výrobky zpět po skončení quy định tạm thời về giới hạn hàm lượng cho phép của
jejich životnosti. Společnost MSI splní požadavky na một số hóa chất độc hại có trong các sản phẩm điện,
odebírání výrobků značky MSI, prodávaných v zemích điện tử”
EU, po skončení jejich životnosti. Tyto výrobky můžete
odevzdat v místních sběrnách. Wireless Radio Use
MAGYAR This device is restricted to indoor use when operating
Annak érdekében, hogy környezetünket megvédjük, in the 2.4GHz, 5GHz frequency band.
illetve környezetvédőként fellépve az MSI emlékezteti Cet appareil doit être utilisé à l’intérieur.
Önt, hogy ...
당해 무선설비는 운용중 전파혼신 가능성이 있음.
Az Európai Unió („EU”) 2005. augusztus 13-án hatályba
lépő, az elektromos és elektronikus berendezések この製品は、周波数帯域 2.4GHz, 5GHz で動作していると
hulladékairól szóló 2002/96/EK irányelve szerint きは、屋内においてのみ使用可能です。
az elektromos és elektronikus berendezések NCC無線設備警告聲明
többé nem kezelhetőek lakossági hulladékként,
és az ilyen elektronikus berendezések gyártói 工作頻率2.4GHz, 5GHz該頻段限於室內使用。
kötelessé válnak az ilyen termékek visszavételére 經型式認證合格之低功率射頻電機，非經許可，公司、商
azok hasznos élettartama végén. Az MSI betartja a 號或使用者均不得擅自變更頻率、加大功率或變更原設
termékvisszavétellel kapcsolatos követelményeket 計之特性及功能。
az MSI márkanév alatt az EU-n belül értékesített
低功率射頻電機之使用不得影響飛航安全及干擾合法通
termékek esetében, azok élettartamának végén. Az
信；經發現有干擾現象時，應立即停用，並改善至無干擾時
ilyen termékeket a legközelebbi gyűjtőhelyre viheti.
方得繼續使用。前項合法通信，指依電信法規定作業之無
ITALIANO 線電通信。低功率射頻電機須忍受合法通信或工業、科學
Per proteggere l’ambiente, MSI, da sempre amica della 及醫療用電波輻射性電機設備之干擾。
natura, ti ricorda che….
Products with radio functionality (EMF)
In base alla Direttiva dell’Unione Europea (EU) sullo
Smaltimento dei Materiali Elettrici ed Elettronici, This product incorporates a radio transmitting
Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, and receiving device. For computers in normal
prodotti appartenenti alla categoria dei Materiali use, a separation distance of 20 cm ensures that
Elettrici ed Elettronici non possono più essere eliminati radio frequency exposure levels comply with EU
come rifiuti municipali: i produttori di detti materiali requirements. Products designed to be operated
saranno obbligati a ritirare ogni prodotto alla fine at closer proximities, such as tablet computers,
del suo ciclo di vita. MSI si adeguerà a tale Direttiva comply with applicable EU requirements in typical
ritirando tutti i prodotti marchiati MSI che sono stati operating positions. Products can be operated without
venduti all’interno dell’Unione Europea alla fine del maintaining a separation distance unless otherwise
loro ciclo di vita. È possibile portare i prodotti nel più indicated in instructions specific to the product.
vicino punto di raccolta Restrictions for products with radio functionality
日本JIS C 0950材質宣言 CAUTION: IEEE 802.11x wireless LAN with
5.15–5.35 GHz frequency band is restricted
日本工業規格JIS C 0950により、2006年7月1日以降に販 for indoor use only in all European Union
売される特定分野の電気および電子機器について、製造 member states, EFTA (Iceland, Norway,
者による含有物質の表示が義務付けられます。 Liechtenstein), and most other European
https://storage-asset.msi.com/html/popup/csr/ countries (e.g., Switzerland, Turkey, Republic of
cemm_jp.html Serbia). Using this WLAN application outdoors might
lead to interference issues with existing radio services.
India RoHS Radio frequency bands and maximum power levels
This product complies with the “India E-waste
(Management and Handling) Rule 2011” and prohibits Features :802.11 a/b/g/n/ac/ax, BT
use of lead, mercury, hexavalent chromium, Frequency Range :2.4GHz, 5GHz, 6GHz
polybrominated biphenyls or polybrominated diphenyl
Modulation :FHSS, DSSS, OFDM
ethers in concentrations exceeding 0.1 weight % and
0.01 weight % for cadmium, except for the exemptions Power Output :10, 20, 23
set in Schedule 2 of the Rule. Channel Band Width :1, 5, 20 ,40 , 80, 160MHz

Regulatory Notices iii

 MS-7D15主板产品中有害物质的名称及含量
有害物质
部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE)

印刷电路板组件* ╳ ○ ○ ○ ○ ○

电池** ╳ ○ ○ ○ ○ ○

外部信号连接头 ╳ ○ ○ ○ ○ ○

线材 ╳ ○ ○ ○ ○ ○

本表格依据 SJ/T 11364 的规定编制。

○: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
╳: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求，但所有部件都符合
欧盟RoHS要求。
* 印刷电路板组件: 包括印刷电路板及其构成的零部件。
** 电池本体上如有环保使用期限标识，以本体标识为主。
■ 上述有毒有害物质或元素清单会依型号之部件差异而有所增减。
■ 产品部件本体上如有环保使用期限标识，以本体标识为主。

限用物質含有情況標示聲明書
設備名稱：電腦主機板 型號(型式)：MS-7D15

限用物質及其化學符號
單元 鉛 汞 鎘 六價鉻 多溴聯苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr+6) (PBB) (PBDE)

電路板 ○ ○ ○ ○ ○ ○

電子元件 ─ ○ ○ ○ ○ ○

金屬機構件 ─ ○ ○ ○ ○ ○

塑膠機構件 ○ ○ ○ ○ ○ ○

備考1. “超出0.1 wt %” 及 “超出0.01 wt %” 係指限用物質之百分比含量超出百分比含量基準值。

備考2. “○” 係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3. “─” 係指該項限用物質為排除項目。

Copyright Technical Support

Micro-Star Int’l Co.,Ltd. If a problem arises with your system and no solution
Copyright © 2021 All rights reserved. can be obtained from the user guide, please
contact your place of purchase or local distributor.
The MSI logo used is a registered trademark of Alternatively, please try the following help resources
Micro-Star Int’l Co., Ltd. All other marks and names for further guidance.
mentioned may be trademarks of their respective
owners. No warranty as to accuracy or completeness is yy Visit the MSI website for technical guide, BIOS
expressed or implied. MSI reserves the right to make updates, driver updates, and other information:
changes to this document without prior notice. http://www.msi.com
yy Register your product at: http://register.msi.com
Revision History
Version 1.0, 2020/12, First release.
Version 1.1, 2021/05, Update SATA info
Version 1.2, 2021/09, Update SATA spec

iv Regulatory Notices