WIRTGEN AMERICA

RHINO PARTS

ROAD AND MINERAL TECHNOLOGIES www.wirtgenamerica.com

TABLE OF CONTENTS
THE ROTATION SYSTEM 4

RHINO CUTTER BITS 5

RHINO CUTTER DRUMS 12

Cutter Drum Specifications Table 13

QUICK-CHANGE TOOLHOLDER SYSTEMS 15

HT11 Quick-Change Toolholder System 17

LONG-LIFE EJECTORS 20

RHINO CONVEYOR BELTS 21

Conveyor Belt Specifications Table 22

RHINO TOOLS 25

2|3
THE ROTATION SYSTEM

Our re-designed Rhino Spring Clip and Rhino Ring improve rotation, reduce cutter
bit wear and make installation easier – all resulting in more savings for you.
The Rhino Spring Clip has a rounder shape, bi-directional retaining tabs, reduced
gap size and is made from thicker material. The Rhino Ring has a larger outside
diameter, smaller inside diameter and larger cone size.

Improved durability
due to optimized Faceted body design
carbide metal tips for efficient operation

Reduced gap size for

reliable bit retention Improved circular
and for proper fit shape results in
with bit shank, proper fit around bit
holder bore and shank and into holder
Rhino Ring to reduce
contamination
Bi-directional
retaining tabs
Thicker material for centrally located away
reliable bit retention from load bearing end
even in extremely prevents spring clip
abusive applications from jamming under
washer
Larger outer diameter
improves holder Smaller inner diameter
protection and compresses spring
prevents formation clip for easier
of ridges or burrs installation and
on holder face reduces contamination

Larger cone, top and Surface coating for

bottom, positively ease of installation
centers bit in holder and removal
bore and prevents
oblong bore wear
 RHINO CUTTER BITS

WM1/13
8x15 LG
Application: Concrete and Hard Asphalt
Characteristics: Mini concrete cutter bit

28
- Cylindrical carbide tip
26 - 13 mm (1/2 inch) shank

55
- 200 bits per bucket
Machines: Small Class Milling Machines
13
Carbide Weight:
9.01 g

WM4/13
8.5 Application: Asphalt
16

16 Characteristics: Mini asphalt cutter bit

28

- Extended carbide tip

26 - 13 mm (1/2 inch) shank
55

- 200 bits per bucket

Machines: Small Class Milling Machines

13
Carbide Weight:
19.68 g

W1-10R
10x25 LG
Application: Concrete and Hard Asphalt
Characteristics: Concrete cutter bit
48

- Cylindrical carbide tip

30
- Puller groove
88

- Long sleeve
- D = 45 anti-wear plate
45 - 50 bits per bucket
4

20 Machines: Small and Middle Class

Carbide Weight:
24.59 g Milling Machines

W1-10-NR
10 x 25 LG
Application: Concrete and Hard Asphalt
Characteristics: Strong, ultra-high, penetrating
48

cutter bit
30 - Cylindrical carbide tip
88

- Puller Groove
- Long sleeve
45 - D = 45 anti-wear plate
- 50 bits per bucket
4

20
Carbide Weight:
24.59 g Machines: Small and Middle Class
Milling Machines

4|5
RHINO CUTTER BITS

W1-13R
13x25 LG
Application: Concrete and Hard Asphalt
Characteristics: Robust concrete cutter bit

48
- Large cylindrical carbide tip
33
- Heavy-duty body

88
- Long sleeve
- D = 45 anti-wear plate
45 - 50 bits per bucket

4
Carbide Weight:
20 Machines: Middle and Large Class
38.78 g Milling Machines

W4ER
8.5
16

16
Application: Asphalt
Characteristics: Universal cutter bit
48

- Extended carbide tip

30
- Puller groove
88

- Long sleeve
- D = 45 anti-wear plate
45 - 50 bits per bucket
4

20 Machines: Small Class Milling Machines

Carbide Weight:
19.68 g

W5ER
9.5
16

17.5
Application: Asphalt
Characteristics: Universal cutter bit
48

- Robust, extended carbide tip

34
- Puller groove
88

- Long sleeve
- D = 45 anti-wear plate
45 - 50 bits per bucket
4

20
Carbide Weight: Machines: Middle and Large Class
23.40 g Milling Machines

W5LEHR
9.5
17.5

Application: Asphalt
17.2
49.5

Characteristics: Universal cutter bit

- Robust, extended carbide tip
34
- Puller groove
90

- Long sleeve
- D = 45 anti-wear plate
45 - 50 bits per bucket
4

20
Carbide Weight: Machines: Middle and Large Class
26.50 g Milling Machines
W6R
10.5

17.5
Application: Asphalt
19
Characteristics: Universal cutter bit for high

48
horsepower requirements
34 - Robust carbide tip

88
- Puller groove
- Long sleeve
45 - D = 45 anti-wear plate
- 50 bits per bucket

7
20
Carbide Weight:
30.17 g Machines: Middle and Large Class
Milling Machines

W6AOCR
11.5
18

19
Application: Asphalt, Concrete, Asphalt Over
Concrete
49

Characteristics: Universal cutter bit for high

35 horsepower requirements
89

- Stout carbide tip

- Heavy-duty body
45 - Long sleeve
- D = 45 anti-wear plate
7

20
Carbide Weight: - 50 bits per bucket
36.37 g Machines: Middle and Large Class
Milling Machines
W6AOCLR
11.5
Application: Asphalt
21

19
Characteristics: Universal cutter bit for high
50.5

horsepower requirements
35 - Robust extended carbide tip
90

- Puller groove
- Long sleeve
45
- D = 45 anti-wear plate
- 50 bits per bucket
7

20
Carbide Weight: Machines: Middle and Large Class
41.00 g Milling Machines

W6SR
10.5
17.5

19
Application: Stabilizing/Recycling, Abrasive
Asphalt
48

Characteristics: Large, long-life body bit for high

37 horsepower requirements
88

- Robust carbide tip

- Large, long-life body
- Long sleeve
45
- D = 45 anti-wear plate
7

20 - 40 bits per bucket

Carbide Weight:
30.17 g Machines: Stabilizers, Middle and Large
Class Milling Machines

6|7
RHINO CUTTER BITS

W6SGR

10
19 Application: Stabilizing
Characteristics: Large, long-life body bit for

41
37 abusive “stabilizing” requirements
- Stout carbide tip

80
- Large, long-life body
- Long sleeve
45 - D = 45 anti-wear plate

7
20 - 40 bits per bucket
Carbide Weight:
22.89 g Machines: Stabilizers

W6ER
10.5
19.6

Application: Asphalt
19
Characteristics: Strong, high-penetration bit for
48

exceptional milling efficiency

34
- Robust extended carbide tip
88

- Puller groove
- Long sleeve
45 - D = 45 anti-wear plate
- 50 bits per bucket
4

20
Carbide Weight:
32.87 g Machines: Middle and Large Class
Milling Machines

W7ER
11
20.5

Application: Asphalt
20.5
Characteristics: Strong, high-penetration bit for
48

exceptional milling efficiency

34 - Large extended carbide tip
88

- Puller groove
- Long sleeve
45 - D = 45 anti-wear plate
- 50 bits per bucket
4

20
Carbide Weight:
41.50 g Machines: Middle and Large Class
Milling Machines

W7HLL
11
20.5

Application: Asphalt
20.5
Characteristics: Strong, high-penetration bit for
48

exceptional milling efficiency

34 - Large extended carbide tip
88

- Heavy-duty body
- Long sleeve
45 - D = 45 anti-wear plate
- 50 bits per bucket
7

20
Carbide Weight:
41.50 g Machines: Middle and Large Class
Milling Machines
W8ER
11.5
Application: Asphalt

23
22
Characteristics: Large cutter bit for extreme,

48
high horsepower requirements
34
- Very large, extended carbide tip

88
- Heavy-duty body
- Long sleeve
45 - D = 45 anti-wear plate
- 50 bits per bucket

7
20
Carbide Weight:
48.37 g Machines: Large Class Milling Machines

W1-13/22R
13x25 LG Application: Concrete and Hard Asphalt
Characteristics: Large, long-life body bit for high
53

horsepower requirements
40
- Cylindrical carbide tip
92

- Large, long-life body

- Long sleeve
45 - D = 45 anti-wear plate
- 40 bits per bucket
7

22
Carbide Weight:
38.78 g Machines: Large Class Milling Machines
with 22mm holders

W1-17/22R
17x28.5 LG Application: Concrete and Hard Asphalt
Characteristics: Large, long-life body bit for high
51

horsepower requirements
40
- Very large cylindrical carbide tip
92

- Large, long-life body

- Long sleeve
45 - D = 45 anti-wear plate
- 40 bits per bucket
7

22
Carbide Weight:
73.69 g Machines: Large Class Milling Machines
with 22mm holders

8|9
RHINO CUTTER BITS

W6-22XR
10.5

17.4
Application: Stabilizing/Recycling

51 (Compressed)
19
Characteristics: Large, long-life body bit for high
horsepower requirements

91.5
- Robust carbide tip
- Body shield
44.5 - Long sleeve
- D = 45 anti-wear shield
22.5 - 40 bits per bucket
Carbide Weight:
30.17 g Machines: Stabilizers/Recyclers

W6SG-22XR 10
43.5 (compressed)
19 Application: Stabilizing
Characteristics: Large, long-life body bit for
abusive “stabilizing” requirements
- Stout carbide tip
84

- Body shield
44.5 - Long sleeve
- D = 45 anti-wear shield
22.5 - 40 bits per bucket
Carbide Weight:
22.89 g Machines: Stabilizers

W6AOC-22XR
11.5
18
51.5 (Compressed)

19
Application: Stabilizing/Recycling
Characteristics: Large, long-life body bit for
abusive “stabilizing” requirements
- Stout carbide tip
92

- Body shield
44.5
- Long sleeve
- D = 45 anti-wear shield
22.5 - 40 bits per bucket
Carbide Weight:
36.37 g Machines: Stabilizers

W8-22XR
11.5
20

Application: Stabilizing/Recycling
51 (compressed)

22
Characteristics: Large, long-life body bit for high
horsepower requirements
91.5

- Large carbide tip

- Body shield
44.5
- Long sleeve
- D = 45 anti-wear shield
22.5 - 40 bits per bucket
Carbide Weight:
43.61 g Machines: Stabilizers/Recyclers
W6SG-25R

10
19
Application: Stabilizing
Characteristics: Large bit for abusive “stabilizing”

64
applications

113.1
43
- Stout carbide tip
- Large body
- 25 mm (1 inch) shank
60 - 20 bits per bucket

9.1
Carbide Weight:
25.5 Machines: Stabilizers
22.89 g

W8-25R
11.5
20

21.6
Application: Stabilizing/Recycling
Characteristics: Large bit for high horsepower
64

requirements
113.2

43 - Very large, extended carbide tip

- Large body
- 25 mm (1 inch) shank
60 - 20 bits per bucket
9.1

Carbide Weight:
25.5 Machines: Stabilizers/Recyclers
43.61 g

W1-15-25R
15
Application: Recycling
24

Characteristics: Large bit for high horsepower

64

requirements
113.2

43 - Robust cylindrical carbide tip

- Large body
- 25 mm (1 inch) shank
60 - 20 bits per bucket
9.1

Carbide Weight:
25.5 Machines: Recyclers
47.82 g

W1-19-25R
19
Application: Recycling
29

Characteristics: Large bit for high horsepower

64

requirements
113.2

43
- Robust cylindrical carbide tip
- Large body
- 25 mm (1 inch) shank
60 - 20 bits per bucket
9.1

Carbide Weight:
25.5 Machines: Recyclers
84.00 g

10 | 11
RHINO CUTTER DRUMS

Wirtgen Heavy-Duty Weld Blocks

• 11 pounds of abrasion-resistant steel
• Inter-linking design for strength and seamless auger flight to
protect leading surfaces from wear and to minimize drag

Wirtgen Heavy-Duty Holders

• Quick-change, bolt-in design
• 4 pounds of abrasion-resistant steel
• Designed to shield weld block from wear
• Long bore (61.7-mm) extends holder life
• Both 20-mm and 22-mm holders fit into standard weld block
• Holder blanks available to modify cutting pattern

Wirtgen Heavy-Duty Kicker Plates

• Quick-change, bolt-in design
• Abrasion-resistant steel alloy containing mixed carbides

Extended Cutter Drum Life With Rhino Heavy-Duty Cutter Bits

• Heavy-duty Rhino washer with cone, 45-mm
• Extended spring clip
• Abrasion-resistant body
• Highest quality carbide tip
PART NO. DESCRIPTION WIDTH (IN)
CAT
40000131 PR450 HT-ELEV, TRIPLE WRAP (GRBOX END: 8" PIN LOC WLD HOLDERS) 73.63
40000243 PM465 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 79.00
40000242 PM465 HT-ELEV, TRIPLE WRAP, FINE 5/16" (8mm) SP, SINGLE STRIKE 79.00
40000132 PM565 / PM565B HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 84.00
40000248 PM565B HT-ELEV, TRIPLE WRAP, FINE 7/16" (8mm) SP SINGLE STRIKE 84.00
CMI
40000133 PR450 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 73.63
40000134 PR525 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP WITH ADAPTER RINGS 84.38
40000135 PR500 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, SAME AS PR800/7/L 85.63
40000136 PR800/7/L HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, HD (THICKER SHELL) 85.63
40000137 PR800/7/L HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 85.63
40000138 PR800/7/S HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 84.50
40000142 PR800/7/12 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 84.38
40000144 PR1000 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 150.00
40000145 PR1050 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 150.00
40000146 RS500/650 PULVERIZER, HT-ELEV, BOLT ON END RINGS, 5/8" (15mm) SP 120.00
40000147 RS500/650/800 PULVERIZER, HT-ELEV, BOLT ON END RINGS, 16 HOLE GB BOLT FL 96.00
40000368 RS500/650/800 PULVERIZER, HT-ELEV, BOLT ON END RINGS, 20 HOLE GB BOLT FL 96.00
40000148 RS500/650/800 STABILIZER, HT-ELEV, BOLT ON END RINGS, 16 HOLE GB BOLT FL 96.00
40000367 RS500/650/800 STABILIZER, HT-ELEV, BOLT ON END RINGS, 20 HOLE GB BOLT FL 96.00
40000149 RS500/650 HT-2 BOLT ON END RING SET, LH (FOR 10513, 10564) NA
40000150 RS500/650 HT-2 BOLT ON END RING SET, RH (FOR 10513, 10564) NA
40000151 RS500/650 HT-2 BOLT ON END RING SET, LH (FOR LARGE 10718) NA
40000152 RS500/650 HT-2 BOLT ON END RING SET, RH (FOR LARGE 10718) NA
40000153 RS500/650 HT-2 SPACER & BASE ASSY, PULV. DRUM (FOR 10513) NA
40000154 RS500/650 HT-2 SPACER & BASE ASSY, END RING (FOR 10496-A01-L & R) NA
40000155 RS500/650 HT-2 SPACER & BASE ASSY, STAB. DRUM (FOR 10564) NA
40000156 RS500/650 HT-ELEV BOLT ON END RING SET, LH (FOR 10781, 10830) NA
40000157 RS500/650 HT-ELEV BOLT ON END RING SET, RH (FOR 10781, 10830) NA
40000158 RS500/650 HT-ELEV SPACER & BASE ASSY, STAB. DRUM (FOR 10781) NA
40000159 RS500/650 HT-ELEV SPACER & BASE ASSY, END RING (FOR 10830-A01-L & R) NA
40000160 RS500/650 HT-ELEV SPACER & BASE ASSY, PULV. DRUM (FOR 10830) NA
40000161 RR500/800, W50 GEARBOX MOUNTING RING NA
40000162 PR525 GEARBOX SPACER RING NA
40000163 PR525 STUB SHAFT SPACER RING NA

12 | 13
RHINO CUTTER DRUMS

PART NO. DESCRIPTION WIDTH (IN)

ROADTEC
40000164 RX45 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 78.00
40000165 RX50 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 78.00
40000194 RX50B HT-ELEV, TRIPLE WRAP, 5/8 (15mm) SP 86.00
40000166 RX60 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 86.00
40000167 RX60B / RX60C HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 86.00
40000168 RX68 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 98.00
40000169 RX68B HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, SPECIAL 102 INCH WIDE 102.00
40000170 RX70 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, BOLT-IN STUB SHAFT BELOW 150.00
40000171 RX70 BOLT-IN STUB SHAFT NA
40000172 RX80 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 150.00
40000244 RX900 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 86.00
INGERSOLL-RAND
40000174 MT7000E HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, W/ STUB SHAFT & ADPTR 77.50
40000175 ***MT7500 / PC2200 HT-ELEV, TRIPLE WRAP, FINE 3/16" (5mm) SP 86.50
40000176 MT7500 / PC2200 HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, W/ STUB SHAFT 86.50
BARBER GREENE
40000177 RX40, HT-ELEV, TRIPLE WRAP, 3/4" (19mm) SP, 1.5" THICK SHELL 75.00
40000178 RX40, HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP, 1.5" THICK SHELL 75.00
MISC
40000180 BOMAG STABILIZER DRUM, HT-ELEV, 5/8" (15mm) SP, W/ STUB SHAFT 79.00
40000109 BARTMILL 500BT HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 36.00
40000121 BARTMILL 500BT HT-ELEV, TRIPLE WRAP, 5/8" (15mm) SP 24.00
40000181 BARTMILL 500BT STUB SHAFT NA
*** MT7500/PC2200 PRIOR TO S/N 5080S WILL REQUIRE STUB SHAFT 58939844.
 QUICK-CHANGE TOOLHOLDER SYSTEM
The original Wirtgen quick-change toolholder system —
the standard of quality and economy
Optimized systems for picks and toolholders
Toolholders are highly stressed components.
Almost the entire engine power is converted into
cutting performance via the toolholders. When
cutting through extremely hard materials, a
toolholder must withstand up to five million load
cycles during its service life and guarantee
optimum rotation of the picks. That is why Wirtgen
engineers attach particular importance to using
extremely wear-resistant materials and optimally
designed toolholder systems.
Wirtgen – setting standards in
toolholder systems
Instead of welding the toolholders onto
the drum as in older machines,
Wirtgen’s concept was to develop
holders which could be replaced
quickly and easily. The first generation
of Wirtgen quick-change toolholders
was ready for series production in
1992 and ensured that worn or
damaged toolholders could be
replaced in a matter of minutes: on site
and without requiring any cut-off or
welding machines. The cash value of
this advantage was immediately
appreciated by the contractors. In
addition to being easy to replace, the
Wirtgen quick-change toolholder
systems are characterized by a long
service life, thanks to the elimination of
welds and the use of high-quality
materials. The success of Wirtgen’s
unique quick-change toolholder
systems is due not only to the detailed
theoretical analysis and computer
simulations, but also to exhaustive
Wirtgen's quick-change toolholder systems (HT11 shown here) set practical tests by customers on
new standards for quick bit changes and accurate positioning of the innumerable sites and in extreme
toolholders: on-site replacement is a simple matter.
special jobs.

14 | 15
QUICK-CHANGE TOOLHOLDER SYSTEM
Top quality manufacturing
The operating costs of road milling
machines and recyclers are largely
determined by the service life of
the tools subject to wear, meaning
the bits and the toolholders.
Consequently, these parts must
meet the highest quality
requirements. Manufacturing by
the forging method makes it
possible to process quality
materials at relatively low cost and
achieve extremely high component
Forging process for the upper part of the quick-change toolholder.
strengths. Tight tolerances are
maintained by subsequent
machining to make the precision
components required for milling
applications such as fine milling.
Subsequent heat treatment and
hardening of the toolholders is of
critical importance. Special
methods are used for this step as
well, in order to obtain high
hardness for low wear, and the
necessary toughness. Only in this
way can a long service life be
achieved under the highly dynamic
loads generated by the milling High-precision, automatic machining of the upper part of the quick-change
toolholder.
process.
 HT11 QUICK-CHANGE TOOLHOLDER SYSTEM
Convenient replacement, fast servicing Upper part HT11-R for improved tool rotation
With the HT11 quick-change toolholder system, Optimum rotation of the cutting tools is often
Wirtgen has engineered a field-proven solution impaired by material soiling the toolholder’s drill
for road milling machines and recyclers making hole. With the upper part type HT11-R, the fine
the operation and servicing of the machines particles of milled material are flushed from the
more convenient, faster and thus more drill hole via a recess at the back of the upper
profitable. Enlarging the contact surface of the part. The bit is essentially prevented from
upper part to completely cover that of the sticking in the bore and the bit can be used for
bottom part ensures a tight fit between the two. a significantly longer period of time due to the
A seal prevents dirt particles from entering the improved rotation. Easier access with the
gap between the upper part and the bottom Wirtgen ejector tools makes life even simpler.
part during the milling operation.

16 | 17
HT11 QUICK-CHANGE TOOLHOLDER SYSTEM
Strong Retaining Bolt:
The retaining bolt in the HT11 quick-
change system is significantly larger
than the one used in the HT3 quick-
change toolholder system. The
M30x2 thread is now combined with a
17 mm hexagonal socket drive which
reliably transfers the necessary
torque of 500 Nm. The conical stud
can transmit enormous clamping
forces and thus minimizes loosening
of the upper part.
HT11 HT3

Bottom Part Covered by Upper Part:

Enlarging the contact surface of the
upper part to completely cover that of
the bottom part ensures an
absolutely even and tight fit between
the two. As a result when the upper
part needs to be quickly replaced on
a job site, the bottom part requires
only minimal cleaning which allows
for quicker and easier part changes.

Seal Between Upper & Bottom Parts:

During the milling process fine dirt
particles combine with water and enter
the gap between the upper and bottom
parts. Occasionally this can cause the
shank of the upper part to jam into the
bottom part making it more difficult to
replace the upper part. In the HT11
quick-change toolholder system, the
bore in the bottom part is protected
against contamination by a seal. This
seal optimizes the position of the upper
part in the bottom part and further
reduces the time required to change
parts.
The HT11 quick-change
toolholder system simplifies
operation and maintenance
of the milling drum:
In designing the HT11 quick-
change toolholder system,
priority was given to simple
operational and reliable Hexagon Plug HT11
maintenance techniques after Part No: 158508
rough use on the job. The result is
simple components that Retainer Screw
HT11 M30x2
guarantee long service life for all Torque 500 Nm
wear parts and the entire milling Part No: 158501

drum. As with the HT3 quick-

change tool-holder system,
just a few parts are needed to
equip a wide variety of milling
drums.

Bottom Part Sealing HT11

Part No: 158509
Dummy Upper Part HT11
Part No: 194755

Toolholder HT11-R Toolholder HT11-R D22 Toolholder HT11-R D25

for shaft diameter D20 for shaft diameter D22 for shaft diameter D25
Part No: 187002 Part No: 199001 Part No: 199002

18 | 19
LONG-LIFE EJECTORS

Long-Life Ejectors:
Strategically placed
ejectors on the milling
drum help to transfer
milled asphalt from the
cutter drum to the
conveyor. Specially
blended carbide
surfaces extend the life
of these ejectors.

Ejector Width 150 Ejector Width 250 mm

mm Part No: 44097

Ejector Width 150 mm Ejector Width 250 mm

Part No: 2140636 Part No: 2140635
 RHINO CONVEYOR BELTS

Fabric
• 3 plies of a durable, synthetic fabric resulting in a 240 lb per inch of width working tension.
• Offers flexibility to operate on small pulleys at high speeds
• Provides increased resistance to gouging, puncturing, and impact at loading points
• Has excellent fastener holding ability
Covers
• Features a 3/16” thick top cover and a 1/16” thick bottom cover
• Made of a durable yet flexible rubber compound designed to withstand the harsh effects of
abrasion, gouging, and weathering
Cleats
• Fully molded into the belt cover: That is, the cleats and cover are one unit. This proven
production method prevents cleats from peeling away from the cover, which can take
place when uncured cleats are vulcanized to a cured belt cover.
• Aggressive 1” high cleats spaced at 10” apart increase production capacity, withstand
abrasion, enhance belt life, and protect the top cover of the belt.
• 1” high integrally molded rubber side curbs are available.
Splice
• Conventional styles of conveyor belting usually fail in the splice area, which is typically
the weakest part of the belt. Our special splicing techniques developed from years of
experience result in a virtually seamless joint that withstands even the toughest
applications.
• Tests show that the Rhino splice is up to 40% stronger than conventional splices in
standard rubber belting.
• Rhino’s one-piece construction, where cleats, cover, fabric, and splice are manufactured as a
single unit, provides the industry’s most durable and productive belt.

20 | 21
RHINO CONVEYOR BELTS
MACHINE BELT POSITION BELT DIMENSION PART NUMBER
CAT
PR450 PICK-UP 30” WIDE X 15’ 1” LONG 40000074
PR450 DISCHARGE 30” WIDE X 50’ 1” LONG 40000075
PM465 PICK-UP 30” WIDE X 18’ 5” LONG 40000118
PM465 DISCHARGE 30” WIDE X 49’ 9” LONG 40000119
PM565 PICK-UP 36” WIDE X 25’ 5” LONG 40000076
PM565 DISCHARGE 30” WIDE X 50’ LONG 40000077
PM565NEW & 201 PICK-UP 39” WIDE X 25’ LONG 40000203
PM565NEW DISCHARGE 36” WIDE X 55’ 6’ LONG 40000279
CMI
PR500 PICK-UP 30” WIDE X 28’ LONG 40000115
PR500 DISCHARGE 30” WIDE X 56’ LONG 40000116
PR525 PICK-UP 36” WIDE X 20’ 9” LONG 40000122
PR525 DISCHARGE 36” WIDE X 49’ 5” LONG 40000079
PR525/7 PICK-UP 36” WIDE X 23’ LONG 40000280
PR750B PICK-UP 36” WIDE X 20’ 4” LONG 40000185
PR750B DISCHARGE 36” WIDE X 58’ LONG 40000184
PR800 PICK-UP 36” WIDE X 28’ 1” LONG 40000080
PR800 DISCHARGE 30” WIDE X 54’ LONG 40000081
PR800 PICK-UP 42” WIDE X 28’ 1” LONG 40000082
PR800 DISCHARGE 36” WIDE X 54’ LONG 40000083
PR800 DISCHARGE 42” WIDE X 55’ 5” LONG 40000187
PR1000 PICK-UP 48” WIDE X 20’ 4” LONG 40000123
PR1000 DISCHARGE 48” WIDE X 57’ 6” LONG 40000124
PR1050 PICK-UP 48.5” WIDE X 30’ 11” LONG 40000084
PR1050 DISCHARGE 48” WIDE X 55’ 5” LONG 40000085
INGERSOLL-RAND
MT6520/PC2000 PICK-UP 24” WIDE X 26’ LONG 40000086
MT6520/PC2000 DISCHARGE 24” WIDE X 43’ 6” LONG 40000087
MT7500/PC2200 VANNER EDGE PICK-UP 39.38” WIDE X 23’ 2” LONG 40000088
MT7500/PC2200 VANNER EDGE DISCHARGE 31.5” WIDE X 52’ 6” LONG 40000089
ROADTEC
RX25D PICK-UP 24” WIDE X 22’ 9” LONG 40000106
RX25D DISCHARGE 24” WIDE X 41’ 5” LONG 40000107
RX45 PICK-UP 32” WIDE X 23’ LONG 40000090
RX45 DISCHARGE 32” WIDE X 49’ 1” LONG 40000091
RX50 PICK-UP 36” WIDE X 26’ 6” LONG 40000098
MACHINE BELT POSITION BELT DIMENSION PART NUMBER
RX50 DISCHARGE 36” WIDE X 48’ 11” LONG 40000093
RX50B PICK-UP 34” WIDE X 21’ 11” LONG 40000283
RX50B DISCHARGE 34” WIDE X 51’ LONG 40000414
RX50W/60/70 PICK-UP 42” WIDE X 26’ 4” LONG 40000092
RX50W/60/70 DISCHARGE 36” WIDE X 48’ 11” LONG 40000093
RX60B PICK-UP 42” WIDE X 26’ 4” LONG 40000092
RX60B DISCHARGE 42” WIDE X 50’ 5” LONG 40000099
RX100 PICK-UP 60” WIDE X 28’ 3” LONG 40000100
RX100 DISCHARGE 54” WIDE X 49’ 1” LONG 40000101
RX700 PICK-UP 36” WIDE X 24’ 9” LONG 40000397
RX700 DISCHARGE 36” WIDE X 53’ 3” LONG 40000398
RX900 PICK-UP 42” WIDE X 28’ 4” LONG 40000339
RX900 DISCHARGE 42” WIDE X 53’ 3” LONG 40000396
BITELLI
200 PICK-UP 31.5” WIDE X 17’ 8” LONG 40000094
200 DISCHARGE 30” WIDE X 54’ LONG 40000081
102C NA 21.5” WIDE X 21’ 8” LONG 40000252
BARBER GREENE
RX40 PICK-UP 24” WIDE X 16’ LONG 40000096
RX40 DISCHARGE 24” WIDE X 48’ LONG 40000097
BARTMILL
300BT - 1/2” CLEETS, MECH SPLICE REQU. N/A 24” WIDE X 17’ LONG 40000103
50B - 1/2” CLEETS, MECH SPLICE REQU. N/A 24” WIDE X 28’ LONG 40000105
CUSTOM
42” WIDE X 67’ LONG N/A N/A 40000188
42” WIDE X 54’ 5” LONG N/A N/A 40000186
36” WIDE X 22’ 9” LONG N/A N/A 40000183
36” WIDE X 28’ 9” LONG N/A N/A 40000128
30” WIDE X 17’ 2” LONG N/A N/A 40000129
30” WIDE X 48’ 4” LONG N/A N/A 40000130
39.5” WIDE X 23’ 5” LONG N/A N/A 40000449
31.5” WIDE X 19’ 4” LONG N/A N/A 40000457
31.5” WIDE X 20’ 2” LONG N/A N/A 40000450
48” WIDE X 30’ 11” LONG N/A N/A 40000195
42” WIDE X 55’ 0” LONG N/A N/A 40000196
42” WIDE X 26’4” LONG N/A N/A 40000197
42” WIDE X 54’ 8” LONG N/A N/A 40000198

22 | 23
RHINO CONVEYOR BELTS
MACHINE BELT POSITION BELT DIMENSION PART NUMBER
RHINO BELTING BY THE FOOT
23.5” WIDE N/A N/A 40000377
24” WIDE N/A N/A 40000378
30” WIDE N/A N/A 40000379
36” WIDE N/A N/A 40000380
42” WIDE N/A N/A 40000381
48” WIDE N/A N/A 40000382
FLEXCO 550 MEGALOY MECHANICAL SPLICE
24” LONG N/A N/A 40000383
30” LONG N/A N/A 40000284
36” LONG N/A N/A 40000384
42” LONG N/A N/A 40000385
48” LONG N/A N/A 40000386
SPLICE INSTALLATION TOOL KIT (TEMPLATE, BORING BIT, WRENCH, BOLT BREAKERS)
24” WIDE N/A N/A 40000387
30” WIDE N/A N/A 40000388
36” WIDE N/A N/A 40000389
42” WIDE N/A N/A 40000390
48” WIDE N/A N/A 40000391
*Add "B" to end of part number for belt with free ends and mechanical splice (550 Megaloy Mechanical Splice)
**Add "C" to end of part number for belt with free ends for vulcanizing in field (Length = Std Length + Width)
 RHINO TOOLS
Rapid replacement of cutter
bits: Bit changes require
machine stoppages. Worn bits
must be driven out and
replaced. Rhino offers the 3/4” Extension
Part No: 40000259
highest quality tools designed
to minimize down time: manual
Hexagon Socket,
ejector drifts and extractors,
17 mm for HT2 & HT11
copper hammers for driving in
Part No: 40000260
the new bits, and pneumatic
tools for changing bits.

Assembly tools for quick- Ratchet 3/4”

change toolholder systems: Part No: 40000261
Special tools are required for
milling drums with quick-
change toolholders. High
quality tools have been Hexagon Socket,
carefully selected by Rhino. 14 mm for HT3
Part No: 40000262
Assembly tools for Surface
Miners: Special snap ring
pliers are available from Rhino
for installing and removing the Torque Wrench
safety snap rings. up to 700 Nm
Part No: 40000278

Adapter for
Thread Cutter
Assembly Pliers Safety Collars Part No: 40000267
for Safety Collar for Surface Miner Tools
Part No: 40000263 Part No: 40000264

Thread Cutter
for HT3 M 24 x 2
Part No: 40000265

for HT11 M 30 x 2
Part No: 40000266

24 | 25
RHINO TOOLS

Cutter Bit Profile Ejector Drift

Gauge for Bits
Part No: 40000392 Part No: 40000315

Extractor for Ejector Drift for Ejector Drift for Copper Hammer
Cutter Bits Cutter Bits Miniature Cutter Bits for Driving
Part No: 40000268 Part No: 40000269 Part No: 40000270 in the Cutter Bits
Part No: 40000271

Pneumatic Hammer Set Pneumatic Ejector Drift

with Driver & Ejector Drift for Cutter Bits
Part No: 40000272 Part No: 40000273

Pneumatic Driver
for Cutter Bits
Accessories Included Part No: 40000274
 Torque Wrench
Part No: 40000245

Toolholder HT01
for shaft diameter D20
Part No: 40000458
Bucket: 20 pieces
Wirtgen Drum
Maintenance Manual
Part No: PTWA2001

Toolholder HT02
for shaft diameter D20
Part No: 40000459
Bucket: 25 pieces

26 | 27
Wirtgen America
6030 Dana Way
Antioch, TN 37013

Illustrations are without obligation. Subject to technical changes. – No. WI-PPRA 02/11 © by Wirtgen America. 2011 Printed in USA
Phone: (615) 501-0600
Fax: (615) 501-0691

www.wirtgenamerica.com

E-mail:
rhino@wirtgenamerica.com